CH-45 OWNER'S MANUAL PARTS

Transcription

1 OWNER'S MANUAL CH-45 PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice All ratings specified are based on structural factors only, not vehicle capacities or capabilities. Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee FORM NO MAY 2000 Phone (423) FAX (423) PRICE $25.00

2 LIMITED WARRANTY MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in material and workmanship for a period of twelve (12) months from date placed in service, but in no event shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve (12) months from date placed in service, whichever is earlier. MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or alterations have been made unless authorized by MILLER. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages concerning or relating to any product or parts, whether based on negligence, strict liability, breach of contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss resulted from any general or particular requirement which MILLER knew or had reason to know about at the time of sale. MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted under applicable law, pass on to the purchaser such manufacturer's or seller's warranty. MILLER, whose policy is one of continuous improvement, reserves the right to improve its products through changes in design or materials as it may deem desirable without being obligated to incorporate such changes in products previously sold. This warranty is not intended to cover or include the following items, which are set forth by way of example and not limitation: A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to weather, road conditions, road treatments, etc. B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure to provide reasonable and necessary maintenance, or uses for which the equipment was not designed or intended. C. Alterations or modifications that affect performance, operation or reliability. D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts. IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY OTHER IMPROPER USE. Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee SERIAL NUMBER Telephone (423)

3 OWNER, USER AND OPERATOR: Challenger appreciates your choice of our wrecker for your application. Our number one priority is user safety which is best achieved by our joint efforts. We feel that you can make a major contribution to safety if you, as the equipment owner and operator: 1. Comply with Federal, State, and Local Regulations. 2. Read, Understand, and Follow the Instructions in this Manual. 3. Use Good, Safe Work Practices in a Common Sense Way. 4. Only have Authorized and Trained Operators running the Wrecker. Also contained in this manual is a Parts Section for your Wrecker. Use of other than Factory or Factory Authorized Parts will render the Warranty void MILLER INDUSTRIES TOWING EQUIPMENT INC. All rights reserved. Reproduction or use, without express permission, of editorial or pictorial content, in any manner, is prohibited. i

4 TABLE OF CONTENTS Section Vl - PARTS SUBFRAME ASSEMBLY... VI-2 & VI-3 BODY ASSEMBLY.... VI-4 & VI-5 BOOM ASSEMBLY... VI-6 & VI-7 UNDERLIFT ASSEMBLY.... VI-8 & VI-9 UNDERLIFT HYDRAULICS.... VI-10 & VI-11 BOOM HYDRAULICS... VI-12 & VI-13 PUMP, VALVE & FILTER HYDRAULICS... VI-14 & VI-15 WINCH HYDRAULICS & AIR FREE SPOOL.... VI-16 & VI-17 LEFT CONTROL ASSEMBLY... VI-18 & VI-19 RIGHT CONTROL ASSEMBLY... VI-20 & VI-21 REAR SPADE HYDRAULICS...VI-22 HYDRAULIC CYLINDERS....VI-23 thru VI-25 GLAD HAND KIT VI-26 LIFT ADAPTERS VI-27 KING PIN & 5TH WHEEL ADAPTER....VI-28 LIGHT KIT...VI-29 thru VI-33 ii

5 Section VI - PARTS This Section is provided by the manufacturer for the purpose of ordering any component part of the CHALLENGER CH-45 Wrecker that may be required when part replacement is necessary. Be certain to use only original equipment replacement parts for warranty purposes as well as for keeping your CHALLENGER CH-45 Wrecker in its original state and optimum operating capacities. When ordering replacement or spare parts be sure to provide the following information to the manufacturer s Parts Department. 1. Manual Number & Date of Publication 2. Manual Page Number 3. Page Title 4. Reference Number of Part Desired 5. Part Number 6. Part Description 7. Quantity of Part Desired Providing this information will help ensure that the correct parts will be delivered to you in an expedient manner without delay. Should additional information be required for repair or replacement of certain components, contact your Wrecker Manufacturer Authorized Representative. The Manufacturer reserves the right, without notice or obligation, to improve or modify their products, which may change the specifications, models and feature availability. VI-1

6 SUBFRAME ASSEMBLY VI-2

7 SUBFRAME ASSEMBLY 1 REF CYLINDER, REAR SPADE CENTER BONDED MOUNT (BE0102) WASHER, SPECIAL (BE0103) 4 REF CYLINDER, BOOM ELEVATION RAMP PAD SCREW, 1/4"-20 X 3/4" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" FL HD SKT SCREW, 3/8"-16 X 1-1/2" HEX SKT SET SCREW, 1/2"-13 X 5" HEX HD CAP SCREW, 1/2"-13 X 1-3/4" HEX HD CAP SCREW, 1/2"-13 X 5-1/2" HEX HD CAP SCREW, 5/8"-11 X 4-1/2" HEX HD CAP SCREW, 3/4"-10 X 3-1/2" HEX HD CAP SCREW, 3/4"-10 X 2-1/2" HEX HD CAP GR SCREW, 3/4"-10 X 6-1/2" HEX HD CAP NUT, 3/8"-16 NYLOK HEX NUT, 1/2"-13 NYLOK HEX NUT, 3/4"-10 NYLOK HEX NUT, 3/4"-10 NYLOK HEX GR LOCKWASHER, 1/4" HELICAL WASHER, 5/8" FLAT LOCKWASHER, 5/8" HELICAL SHAFT, LOWER JACK SHAFT, UPPER SPADE COVER, SPADE TUBE PIN, SPADE PAD PIN, LIFT CYLINDER FRONT BODY MTG TUBE SPADE PAD SPADE, LEFT INNER SPADE, RIGHT INNER PIVOT PIN WELDMENT, LIFT CYLINDER SUBFRAME WELDMENT BOOM PIVOT BRACKET SAFETY CHAIN ASSEMBLY (NOT SHOWN) SAFETY CHAIN, SYSTEM 10, 1/2" x 14' SCREW, 1/2"-13 X 1-3/4" HEX HD CAP NUT, 1/2"-13 NYLOK HEX WASHER, 1/2" FLAT VI-3

8 BODY ASSEMBLY VI-4

9 BODY ASSEMBLY 1 28 FT RUBBER FENDER MUDFLAP DOOR CHECK, 11" LIGHT BAR, DELUXE (OPTIONAL) LEFT TOOL COMPARTMENT, 156" C.B RIGHT TOOL COMPARTMENT, 156" C.B BACK UP ALARM (NOT SHOWN) SCREW, 1/4"-20 X 3/4" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SCREW, 3/4"-10 X 2-1/2" HEX HD CAP GR CLIP, 1/4" TINNERMAN NUT, 3/8"-16 NYLOK HEX NUT, 3/4"-10 NYLOK HEX GR WASHER, 1/4" FLAT RIVET, 1/4" MUDFLAP MTG ANGLE, LEFT MUDFLAP MTG ANGLE, RIGHT BAR, MUDFLAP RETAINING STRIP, FENDER TAILGATE MOUNTING ANGLE MOUNTING PLATE MOUNTING PLATE SPACER, REAR FRAME BRACKET SWITCH PANEL, RIGHT CONTROL PANEL, RIGHT GUAGE PANEL CONTROL PANEL VERTICAL SUPPORT, L.H VERTICAL SUPPORT, R.H MOUNTING BRACKET TOP CHANNEL CHALLENGER NAMEPLATE KIT VI-5

10 BOOM ASSEMBLY VI-6

11 BOOM ASSEMBLY GREASE FITTING SHEAVE, 10" SLIDE PAD, BOOM BOTTOM COMPRESSION SPRING BUSHING, 3-1/2" O.D. X 3" I.D. X 2-1/2" 6 REF> CYLINDER, EXTEND SNAP RING, INTERNAL SCREW, 3/8"-16 X 3/4" HEX HD CAP SCREW, 3/8"-16 X 1-1/2" HEX HD CAP SCREW, 3/8"-16 X 3" HEX HD CAP SCREW, 3/8"-16 X 4" HEX HD CAP SCREW, 5/8"-11 X 1" HEX HD CAP NUT, 3/8"-16 NYLOK HEX NUT, 1/2"-13 NYLOK HEX lockwasher, 3/8" HELICAL WASHER, 1/2" FLAT WASHER, 5/8" X 1-3/4" FLAT LOCKWASHER, 5/8" HELICAL COTTER PIN, 1/8" X 3/4" SS ROLL PIN, 1/2" X 1-1/4" BOTTOM, CABLE GUIDE SHAFT, SHEAVE SLIDE PAD TOP SPACER, OUTER BOOM PIVOT PIN, BOOM PIVOT ROD SPRING CHANNEL PIN, TILT CYLINDER BASE PIN, EXTEND CYLINDER (BASE) PIN, EXTEND CYLINDER (ROD) PLATE, FLAPPER DP 45,000 LB. WINCH BOOM END SWIVEL, LEFT BOOM END SWIVEL, RIGHT CABLE GUIDE SPRING PIN INNER BOOM WELDMENT TENSIONER MOUNTING PLATE TENSIONER BRACKET OUTER BOOM WELDMENT VI-7

12 UNDERLIFT & TOWER ASSEMBLY VI-8

13 UNDERLIFT & TOWER ASSEMBLY SNAP RING, 1" GREASE FITTING COMPRESSION SPRING, CROSSBAR STEEL BALL, 1-3/16" DIA OBLONG LINK 6 REF CYLINDER, BOOM EXTENSION SLIDE PAD SLIDE PAD O-RING, PIVOT PIN SPRING 11 REF CYLINDER, FOLD BUSHING, 3.5" O.D. X 3" I.D. X 2.5" SPRING 13 REF CYLINDER, TILT BUSHING, PIVOT PIN WASHER, THRUST WASHER, THRUST SCREW, #10 TYPE "U" DRIVE SCREW, 3/8"-16 X 3/4" HEX HD CAP SCREW, 3/8"-24 X 3/4" HEX HD CAP GR SCREW, 3/8"-24 X 5/8" FLAT SKT HD SCREW, 1/2"-13 X 1" HEX HD CAP SCREW, 1/2"-13 X 1-1/4", SKT HD CAP SCREW, 1/2"-13 X 3" HEX HD CAP GR SCREW, 1/2"-13 X 5" HEX HD CAP SCREW, 5/8"-11 X 4-1/2" SKT HD CAP NUT, LOCK 1/2" LOCKWASHER, 3/8" EXT. TOOTH LOCKWASHER, 3/8" LOCKWASHER, 1/2" HELICAL LOCKWASHER, 5/8" PLATE, STOP, OUTER BOOM PLATE, STOP SHAFT, INNER BOOM CYLINDER SHAFT, OUTER BOOM CYLINDER PAD, SLIDER PIN PIN, TILT CYLINDER BASE PIN, TILT CYLINDER ROD SPACER, DETENT SPRING PIN, PIVOT, TOP HALF PIN, PIVOT, BOTTOM BAR, RETRACT 43 REF TEE HANDLE BOOM, 2ND STAGE 45 REF FORK ADAPTER, L.H. (SHOWN) 46 REF FORK ADAPTER, R.H BOOM, OUTER UNDERLIFT TOWER PIN, FOLD CYLINDER TOWER PIVOT PIN PIN, UNDERLIFT PIVOT CROSSBAR BOOM, 3RDSTAGE 54 REF PIN, RETAINER VI-9

14 UNDERLIFT HYDRAULICS VI-10

15 UNDERLIFT HYDRAULICS CONNECTOR, 6MJ-8MB BRANCH TEE, 6MJ-6MJ-4MP ELBOW, 6MJ-6MP CONNECTOR, 6MJ-6MP HOSE ASSEMBLY, 18" ELBOW, 6MJ-8MP CONNECTOR, 6MJ-6MB ELBOW, 6MJ-6MB DOUBLE HOLDING VALVE HOLDING VALVE INLINE ORIFICE HOSE ASSEMBLY, 18" TUBE ASSEMBLY ADAPTER, 8MJ-6MJ 15 REF CYLINDER, FOLD 16 4 PR CLAMPING UNIT SPLIT BUSHING STACKING NUT, SKT HD BULKHEAD UNION W/NUT HOSE ASSEMBLY, 50" 21 REF CYLINDER, TILT 22 REF CONTROL VALVE, VDP11DDC HOSE ASSEMBLY, 10" HOSE ASSEMBLY, 78" HOSE ASSEMBLY, 108" TEE, 8MJ-8MJ-8MB HOSE ASSEMBLY, 88" HOSE ASSEMBLY, 35" HOSE ASSEMBLY, 12" CONNECTOR, 8MB-6FB HOSE ASSEMBLY, 30" HOSE ASSEMBLY, 48" 33 REF CYLINDER, EXTEND HOSE ASSEMBLY, 24" HOSE ASSEMBLY, 37" HOSE ASSEMBLY, 27" SCREW, 5/16"-18 X 3/4" HEX HD CAP VI-11

16 BOOM HYDRAULICS VI-12

17 BOOM HYDRAULICS CONNECTOR, 8MJ-8MB GREASE FITTING HOSE CLAMP, 8" HOSE ASSEMBLY, 46" HOSE ASSEMBLY, 45" CONNECTOR, 6MJ-8MB ELBOW, 8MJ-8Mb HOLDING VALVE CONNECTOR, 6MJ-10MB ELBOW, 8MJ-6MP90 11 REF CONTROL VALVE, VDP12CDD HYDRAULIC TUBING WIRE TIE, 29-3/4" (NOT SHOWN) BULKHEAD RUN TEE, 8MJ-BLKHD-8MJ BULKHEAD UNION, 8MJ-8BLKHD LIFT CYLINDER TEE, 8MJ-8MJ-8FJX ELBOW, 8MJ-4MP EXTEND CYLINDER CONNECTOR, 8MJ-6MP HOSE ASSEMBLY, 45" HOSE ASSEMBLY, 48" HOSE ASSEMBLY, 50" HOSE ASSEMBLY, 33" HOSE ASSEMBLY, 33" SCREW, 1/4"-20 X 2-1/4" RD HD SLOTTED NUT, 1/4"-20 HEX WASHER, 1/4" FLAT LOCKWASHER, 1/4" HELICAL MOUNTING BRACKET, CHECK VALVE VI-13

18 PUMP, VALVE & FILTER HYDRAULICS VI-14

19 PUMP, VALVE & FILTER HYDRAULICS ELBOW, 8MJ-10MB RETURN LINE FILTER ASSEMBLY BUSHING, 1-1/4" X 1" CLAMP, HOSE, 1" - 2-1/4" HOSE BARB, 2", 32C4-32MP PIPE PLUG, 3/4" NPT 7 15 FT SUCTION HOSE, 2" ELBOW, 12MJ-12MP BARB, 24C4-24MP FT SUCTION HOSE, 1-1/2" PIPE BUSHING, 2" NPT TO 1-1/2" NPT ELBOW, 12MJ-12MB ELBOW FLANGE, 32-32FL90 W/ FLANGE KIT HOSE ASSEMBLY, 150" ELBOW, 6MJ-6FJX HYDRAULIC PUMP, OPPOSITE ENGINE FILTER ASSEMBLY, SPIN-ON ELBOW, 8MJ-12FL O-RING FLANGE KIT, 12FH BALL VALVE, BRONZE HOSE ASSEMBLY, 131" ADAPTER, 8FJ-6MJ RUN TEE, 8MJ-8FJX-8MJ ELBOW, 16MJ-12MB GAUGE, HYDRAULIC PRESSURE CENTER BONDED MOUNT SPECIAL WASHER FLANGE FITTING, 24-24fl CONTROL VALVE, VDP12CDD PIPE NIPPLE, 2" X 4" AIR SHIFT PTO (NOT SHOWN) SIGHT GAUGE CONNECTOR, 6MJ-4FP CONTROL VALVE, VDP11DDC TEE, 12MJ-12FJX-12MJ ADAPTER, 12FJ-6MJ HOSE ASSEMBLY, 120" ELBOW, 12MJ-20FL90 W/ FLANGE KIT HOSE CLAMP, 2-1/2" INSULATED ELBOW, 16MJ-16MP HOSE ASSEMBLY, 50" HOSE ASSEMBLY, 36" FILLER CAP SCREW, 1/4"-20 X 3-1/2" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SCREW, 3/8"-16 X 2-1/2" HEX HD CAP SCREW, 1/2"-13 X 1-1/4" HEX HD CAP NUT, 1/4"-20 HEX NYLOK NUT, 3/8"-16 HEX NYLOK WASHER, 1/4" FLAT LOCKWASHER, 3/8" HELICAL LOCKWASHER, 1/2" HELICAL GASKET, CLEANOUT & FILLER COVER RESERVOIR WELDMENT, LEFT RESERVOIR WELDMENT, RIGHT FILLER PIPE WELDMENT RESERVOIR SUPPORT WELDMENT VI-15

20 WINCH HYDRAULICS & AIR FREE SPOOL VI-16

21 WINCH HYDRAULICS & AIR FREE SPOOL VALVE, SOLENOID AIR CONTROL RUBBER GROMMET BULKHEAD UNION, 3/4" JIC 4 10 FT AIR HOSE, 1/4" O.D CONNECTOR, 4TB-4MP 6 10 FT CONVOLUTED LOOM, 3/8" TEE UNION, 4TB-4TB-4TB BREATHER VENT, 1/8" MP ELBOW, 1/4" TUBE X 1/8" MP CONNECTOR, 10MJ-10MB CLAMPING UNIT STACKING NUT, SKT HD SPLIT BUSHING, 1" CONNECTOR, 10MJ-8MB HOSE ASSEMBLY, 46" HOSE ASSEMBLY, 48" HOSE ASSEMBLY, 81" HOSE ASSEMBLY, 89" HOSE ASSEMBLY, 105" HOSE ASSEMBLY, 117" WINCH, DP MODEL S50-50K, SINGLE SPEED SCREW, #10-32 X 1/2" RD HD PHIL SCREW, 5/16"-18 X 3/4" HEX HD CAP SCREW, 3/4"-10 X 2-1/2" HEX HD CAP NUT, 3/4" HEX NYLOK LOCKWASHER, #10 HELICAL ANGLE - WINCH MOUNTING ANGLE - WINCH MOUNTING ANGLE - WINCH MOUNTING ANGLE - WINCH MOUNTING 31 2 GX263 ELBOW, 10MJ-10MB90 VI-17

22 LEFT CONTROL ASSEMBLY VI-18

23 LEFT CONTROL ASSEMBLY REMOTE CONTROL ASSEMBLY CONTROL KNOB, W/L (UP/DOWN) CONTROL KNOB, (IN/OUT) CONTROL KNOB, BOOM (UP/DOWN) CONTROL KNOB, JACK (UP/DOWN) CONTROL KNOB, BOOM (IN/OUT) CONTROL CABLE, 96" CONTROL CABLE, 104" GREASE FITTING, 1/4"-28 X CONTROL KNOB, TILT (UP/DOWN) CONTROL KNOB, W/L EXTEND (IN/OUT) ADJUSTABLE CLEVIS CONTROL CABLE, 114" SCREW, 1/4"-20 X 3/4" HEX HD CAP SCREW, 5/16"-18 X 1-1/4" HEX HD CAP SCREW, 5/16"-18 X 2-1/2" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" HEX HD CAP NUT, 1/4"-20 HEX NYLOK NUT, 5/16"-18 "J" TINNERMAN NUT, 5/16"-18 HEX NYLOK NUT, 5/16"-24 HEX NUT, 3/8"-16 HEX NYLOK NUT, 3/8"-16 HEX JAM WASHER, 1/4" FLAT WASHER, 5/16" INTERNAL TOOTH WASHER, 3/4" FLAT (SPECIAL) CLEVIS PIN, 5/16" X 1" COTTER PIN, 1/16" X 3/4" CLAMP, SHAFT CONTROL BOX PLATE, SHAFT SUPPORT PIN, CONTROL BOX SUPPORT, CONTROL (LEFT) SUPPORT, CONTROL (RIGHT) CONTROL CABLE CONNECTOR CONTROL FRAME WELDMENT CONTROL HANDLE WELDMENT REMOTE CONTROL ASSEMBLY / WIRE CONNECTOR, SPADE ELBOW, 4TB-4MP / AIR HOSE, 1/4" O.D. (FT.) 39 2 / CONNECTOR, 4TB-4MP 40 2 / BRASS PLUG, 4MP CABLE SEALING GRIP HEX PIPE BUSHING CONVOLUTED LOOM, 3/8" X 8" / CABLE TIE, 4" 18 LB / BREATHER VENT, 2MP / ELBOW, 4TB-2MP AIR SOLENOID VALVE (8) AIR SOLENOID VALVE (14) CIRCUIT BREAKER, HI-AMP WATERPROOF 49 1 / TERMINAL BLOCK POWER PAL, 15 POSITION POWER PAL, 8 POSITION 52 8 / ELECTRICAL CABLE, 16/10 SO (FT.) 53 4 / AIR CYLINDER AIR FILTER/REGULATOR AIR LUBRICATOR MOUNTING BRACKET 57 2 / SCREW, #8-32 X 3/4" RD HD SLOTTED 58 4 / SCREW, 1/4"-20 X 1-1/4" HEX HD CAP 59 2 / SCREW, 1/4"-20 X 2" HEX HD CAP 60 2 / HEX NUT & STAR WASHER, # / NUT, 1/4"-20 HEX NYLOK 62 4 / NUT, 7/16"-20 HEX JAM 63 2 / WASHER, 1/4" FLAT 64 4 / CLEVIS PIN, 5/16" X 5/8" COTTERLESS SUPPORT, SOLENOID VALVE (8) SUPPORT, SOLENOID VALVE (14) 66 4 / CLEVIS WELDMENT 67 1 HA0132 GAUGE, PSI VI-19

24 RIGHT CONTROL ASSEMBLY VI-20

25 RIGHT CONTROL ASSEMBLY CONTROL KNOB, (IN/OUT) CONTROL KNOB, BOOM (UP/DOWN) CONTROL KNOB, JACK (UP/DOWN) CONTROL KNOB, BOOM (IN/OUT) CONTROL CABLE, 104" GREASE FITTING, 1/4"-28 X ADJUSTABLE CLEVIS CONTROL CABLE, 114" SCREW, 5/16"-18 X 1-1/4" HEX HD CAP SCREW, 5/16"-18 X 2-1/2" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" HEX HD CAP NUT, 5/16"-18 "J" TINNERMAN NUT, 5/16"-18 HEX NYLOK NUT, 5/16"-24 HEX NUT, 3/8"-16 HEX NYLOK NUT, 3/8"-16 HEX JAM WASHER, 5/16" INTERNAL TOOTH WASHER, 3/8" FLAT WASHER, 3/4" FLAT (SPECIAL) CLEVIS PIN, 5/16" X 1" COTTER PIN, 1/16" X 3/4" CLAMP, SHAFT CONTROL BOX PIN, CONTROL BOX SUPPORT, CONTROL (LEFT) SUPPORT, CONTROL (RIGHT) CONTROL FRAME WELDMENT CONTROL HANDLE WELDMENT VI-21

26 REAR SPADE HYDRAULICS CONNECTOR, 6MJ-8MB CONNECTOR, 6MJ-6MB HOSE CLAMP, 5/8" INSULATED (NOT SHOWN) 4 REF CONTROL VALVE, VDP12CDD CONNECTOR, 8MB-6FB HYDRAULIC CYLINDER HOSE ASSEMBLY, 136" VI-22

27 HYDRAULIC CYLINDERS BOOM ELEVATION CYLINDER (COMPLETE) SEAL KIT, BOOM ELEVATION CYLINDER BOOM EXTENSION CYLINDER (COMPLETE) SEAL KIT, BOOM EXTENSION CYLINDER VI-23

28 HYDRAULIC CYLINDERS UNDERLIFT TILT CYLINDER (COMPLETE) SEAL KIT, UNDERLIFT TILT CYLINDER UNDERLIFT EXTEND CYLINDER (COMPLETE) SEAL KIT, UNDERLIFT EXTEND CYLINDER VI-24

29 HYDRAULIC CYLINDERS CYLINDER, UNDERLIFT FOLD (COMPLETE) SEAL KIT, UNDERLIFT FOLD CYLINDER CYLINDER, REAR SPADE (COMPLETE) SEAL KIT, REAR SPADE CYLINDER VI-25

30 GLAD HAND KIT RECEPTACLE BOOT GLAD HAND COUPLING GLAD HAND PLUG BULKHEAD CONNECTOR ADAPTER, 1/4" NPM X 3/8" SYN. HOSE HD 7-WAY TRAILER CONNECTOR SCREW, 1/4"-20 X 1" HEX HD CAP NUT, 1/4"-20 HEX NYLOK WASHER, 1/4" FLAT WASHER, 5/16" FLAT AIR HOSE, 3/8" X 48" SYNFLEX VI-26

31 LIFT ADAPTERS FORK, SHORT (3" OPENING) FORK, SHORT (4-1/2" OPENING) FORK, MEDIUM (3" OPENING) FORK, MEDIUM (4-1/2" OPENING) FORK, LONG (3" OPENING) FORK, LONG (4-1/2" OPENING) FORK, OFFSET REAR AXLE (6" OPENING) HAIR PIN COTTER, 1-1/4" MODIFIED BOLT TEE HANDLE CHAIN HOOK ADAPTER, R.H CHAIN HOOK ADAPTER, L.H RISER BRACKET SPRING LIFT BRACKET OFFSET FORK ADAPTER, LT OFFSET FORK ADAPTER, RT RETAINER PIN ASSEMBLY RETAINER PIN, SPRING LIFT BRACKET VI-27

32 KING PIN ADAPTER KING PIN ADAPTER WELDMENT FIFTH WHEEL ADAPTER (COMPLETE) ROLL PIN, 3/8" X 1-1/2" 3 2 HD1259 SNAPPER PIN 4 1 VA0660 FIFTH WHEEL PIVOT PLATE WELDMENT 5 1 VA0661 PULL PIN WELDMENT 6 1 VA0662 PIVOT PIN WELDMENT PINTLE HOOK KIT (COMPLETE) PINTLE HOOK (NOT SHOWN) SCREW, 1/2"-13 X 1" HEX HD CAP LOCKWASHER, 1/2" HELICAL TH WHEEL, KING PIN ADAPTER & PINTLE HOOK BRACKET WELDMENT RETAINING PIN ASSEMBLY VI-28

33 LIGHT KIT LIGHT, STOP & TURN ( COMPLETE) LIGHT, BACK-UP (COMPLETE) SCREW, #8-32 x 3/4" RD HD SLOTTED VI-29

34 LIGHT KIT REF. PART NO. NUMBER DESCRIPTION LIGHT BAR ASSEMBLY (COMPLETE) BULB, MARKER LIGHT LENS, 3-LIGHT BAR REF. PART NO. NUMBER DESCRIPTION LIGHT, TURN (COMPLETE) BEZEL MOUNTING SCREW CHROME BEZEL LENS & BULB ASSEMBLY GROMMET & PLUG KIT VI-30

35 LIGHT KIT REF. PART NO. NUMBER DESCRIPTION LIGHT, FLOOD (COMPLETE) REF. PART NO. NUMBER DESCRIPTION LIGHT, DOME (COMPLETE) VI-31

36 LIGHT KIT REF. PART NO. NUMBER DESCRIPTION GROMMET & PLUG, MARKER LIGHT SEALED MARKER LIGHT, RED SEALED MARKER LIGHT, AMBER REF. PART NO. NUMBER DESCRIPTION BRACKET, LICENSE PLATE LICENSE PLATE ILLUMINATOR (COMPLETE) BULB, LICENSE PLATE ILLUMINATOR VI-32

37 LIGHT KIT REF. PART NO. NUMBER DESCRIPTION LIGHT, AMBER MARKER (COMPLETE) VI-33

38 NOTES

39 NOTES

40 Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee (423)