V30 INSTALLATION, OPERATION, MAINTENANCE & PARTS

Transcription

1 OWNER'S MANUAL V30 INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice All ratings specified are based on structural factors only, not vehicle capacities or capabilities Hilltop Drive FORM NO Ooltewah, Tennessee / 04 Phone (423) FAX (423) PRICE $25.00

2 LIMITED WARRANTY MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in material and workmanship for a period of twelve (12) months from date placed in service, but in no event shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve (12) months from date placed in service, whichever is earlier. MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or alterations have been made unless authorized by MILLER. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages concerning or relating to any product or parts, whether based on negligence, strict liability, breach of contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss resulted from any general or particular requirement which MILLER knew or had reason to know about at the time of sale. MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted under applicable law, pass on to the purchaser such manufacturer's or seller's warranty. MILLER, whose policy is one of continuous improvement, reserves the right to improve its products through changes in design or materials as it may deem desirable without being obligated to incorporate such changes in products previously sold. This warranty is not intended to cover or include the following items, which are set forth by way of example and not limitation: A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to weather, road conditions, road treatments, etc. B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure to provide reasonable and necessary maintenance, or uses for which the equipment was not designed or intended. C. Alterations or modifications that affect performance, operation or reliability. D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts. IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY OTHER IMPROPER USE. Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee SERIAL NUMBER Telephone (423)

3 Section VI - PARTS This Section is provided by the manufacturer for the purpose of ordering any component part of the VULCAN V30 that may be required when part replacement is necessary. Be certain to use only original equipment replacement parts for warranty purposes as well as for keeping your VULCAN V30 in its original state and optimum operating capacities. When ordering replacement or spare parts be sure to provide the following information to the manufacturer s Parts Department. 1. Manual Number & Date of Publication 2. Manual Page Number 3. Page Title 4. Reference Number of Part Desired 5. Part Number 6. Part Description 7. Quantity of Part Desired Providing this information will help ensure that the correct parts will be delivered to you in an expedient manner without delay. Should additional information be required for repair or replacement of certain components, contact your Manufacturer Authorized Representative. The Manufacturer reserves the right, without notice or obligation, to improve or modify their products, which may change the specifications, models and feature availability. VI-1

4 SUBFRAME ASSEMBLY VI-2

5 SUBFRAME ASSEMBLY KIT, 'D' RING 'D' RING 2 2 BA0259 PIN, 'D' RING 3 2 HD0106 SPRING PIN, 1/4" X 1-3/4" SUBFRAME WELDMENT BODY INSTALLATION KIT SCREW, 1/2"-13 X 1-1/4" HEX HD CAP GR SCREW, 1/2"-13 X 4" HEX HD CAP GR NUT, 1/2"-13 HEX NYLOK WASHER, 1/2" SAE HARDENED LOCKWASHER, 1/2" HELICAL SCREW, 1/2"-13 X 4-1/2" HEX HD CAP TOOLBOX MOUNTING PAD TUBE, BOX MOUNTING BRACKET, BODY TUBE WASHER, 1/2" ID X 2" OD X.150 FLAT BOOM PIVOT ASSEMBLY GREASE FITTING, SCREW, 5/16" NC X 1-3/4" HEX HD CAP GR SCREW, 5/8"-11 X 2-1/2" HEX HD CAP GR NUT, 5/16"-18 HEX NYLOK NUT, 5/8"-11 HEX NYLOK WASHER, 5/16" FLAT WASHER, 5/8" FLAT PLATE, WASHER RETAINING RING PLATE PIVOT BLOCK WELDMENT, LH PIVOT BLOCK WELDMENT, RH BEARING, 2-1/2" SPHERICAL PLAIN LIFT CYLINDER ASSEMBLY GREASE FITTING, 1/4"-28 STRAIGHT SCREW, 3/8"-16 X 7/8" HEX HD CAP GR SHIM, 1-1/2" ID X 2-1/8" OD X 1/8" WASHER, 3/8" FLAT LOCKWASHER, 3/8" HELICAL PIN WELDMENT, LIFT CYLINDER CYLINDER, BOOM LIFT JACK ASSEMBLY 34 2 HD0106 SPRING PIN, 1/4" X 1-3/4" GREASE FITTING, 1/4"-28 STRAIGHT LYNCH PIN SCREW, 5/16"-18 X 1" HEX HD CAP GR WASHER, 5/16" FLAT LOCKWASHER, 5/16" HELICAL ROLL PIN, 3/8" X 3" PIN, RETAINING RETAINING RING, 1-1/4" NOM HEAVY DUTY SNAP RING, 1-1/4" NOM INTERNAL PIN, UPPER TILT CYLINDER PIN, EXTENSION CYLINDER PIN, SPADE EXTENSION CYLINDER (ROD) COVER, JACK INNER SPADE WELDMENT FLIPPER WELDMENT, SPADE CYLINDER, JACK LEG BOOM WEAR PAD ASSEMBLY NUT, 5/16"-18 HEX NYLOK SCREW, 5/16"-18 X 1-1/2" FL HD SKT BOOM GUIDE PAD, BODY ASSY LH BOOM GUIDE PAD, BODY ASSY RH REAR TRAY ASSEMBLY NUT, #8-32 HEX NYLOK SS SCREW, #8-32 X 1/2" FL HD PH MACH SCREW, 5/16"-18 X 1" HEX HD CAP GR WELDNUT, 5/16" WASHER, 10 SAE FLAT WASHER, 1/4" FLAT LOCKWASHER, 5/16" HELICAL PLATE, BOX DOOR REAR TRAY WELDMENT PIANO HINGE, 12" LONG CHAIN BOX ASSEMBLY PANEL, CHAIN BOX LH PANEL, CHAIN BOX RH SAFETY CHAIN KIT CHAIN ASSEMBLY, 5/16" G7 X 12' SCREW, 3/8"-16 X 1-1/4" HEX HD CAP NUT, 3/8"-16 HEX NYLOK WASHER, 3/8" FLAT COVER PLATE ASSEMBLY SCREW, 1/4"-20 X 1" HEX HD CAP SS WASHER, 1/4" FLAT SS LOCKWASHER, 1/4" HELICAL SS COVER PLATE VI-3

6 BODY ASSEMBLY VI-4

7 BODY ASSEMBLY LH BODY ASSEMBLY, SS SPLASH GUARD ASSEMBLY, LH SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SS SCREW, 3/8"-16 X 4-1/2" HEX HD CAP SS WASHER, 3/8" FLAT 316 SS NUT, 3/8"-16 HEX NYLOK SS SPLASH GUARD WELDMENT, LH FENDER KIT, LH SCREW, 1/4"-20 X 1" HEX HD CAP SS WASHER, 1/4" FLAT SS NUT, 1/4"-20 HEX NYLOK SS FENDERETTE PANEL WELDMENT, LH FENDER KIT, RH SCREW, 1/4"-20 X 1" HEX HD CAP SS WASHER, 1/4" FLAT SS NUT, 1/4"-20 HEX NYLOK SS FENDERETTE PANEL WELDMENT, RH RH BODY ASSEMBLY, SS SPLASH GUARD ASSEMBLY, RH SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SS SCREW, 3/8"-16 X 4-1/2" HEX HD CAP SS WASHER, 3/8" FLAT 316 SS NUT, 3/8"-16 HEX NYLOK SS SPLASH GUARD WELDMENT, RH LIGHT KIT, VULCAN V LIGHT, RED 45 STT LED LIGHT, AMBER 45 TURN LED LIGHT, RED LED RECTANGULAR 4" X 1" BASE MOUNT FOR LIGHT, BLACK LIGHT, RED LED RECTANGULAR 2" X 6" LIGHT, AMBER LED RECTANGULAR 4" X 1.18" INTERIOR & COMPARTMENT LIGHT W/SWITCH BODY RUBBER KIT, V FT DECORATIVE TRIM FT RUBBER SEAL FT RUBBER STRIP MUD FLAP KIT, V SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SS SCREW, 3/8"-16 X 1-1/2" HEX HD CAP SS WASHER, 3/8" FLAT 316 SS NUT, 3/8"-16 HEX NYLOK SS MUD FLAP, RUBBER MUD GUARD, LH MUD GUARD, RH MUD FLAP BRACKET, LH MUD FLAP BRACKET, RH BACK UP STRIP, MUD FLAP " SS TUNNEL BOX ASSEMBLY CABLE TIE JUNCTION BOX, 10 POLE BOX KIT FOR SS TUNNEL BOX INTERIOR & COMPARTMENT LIGHT W/SWITCH FT RUBBER SEAL WIRING HARNESS, TUNNEL BOX LIGHT " SS TUNNEL BOX 48 4 GV57 RUBBER GROMMET " SS TUNNEL BOX ASSEMBLY CABLE TIE JUNCTION BOX, 10 POLE SS SPACER BOX KIT, 36" TUNNEL INTERIOR & COMPARTMENT LIGHT W/SWITCH FT RUBBER SEAL WIRING HARNESS, TUNNEL BOX LIGHT " SS TUNNEL BOX 56 4 GV57 RUBBER GROMMET VI-5

8 RECOVERY BOOM ASSEMBLY VI-6

9 RECOVERY BOOM ASSEMBLY GREASE FITTING, 1/4"-28 STR SHEAVE, 8" TIE DOWN STRAP, 15" SNAP RING, 1-1/4" RETAINING RING, 3-1/2" EXTERNAL GREASE FITTING, 1/8" STR FT SYNFLEX HOSE, 3/8" WIRE ROPE, 1/2" X 150' SCREW, 1/4"-20 X 5/8" HEX HD CAP SCREW, 1/4"-20 X 2" HEX HD CAP SCREW, 5/16"-18 X 1-1/4" HEX HD CAP SCREW, 3/8"-16 X 1" HEX HD CAP SCREW, 3/8"-16 X 5/8" HEX HD CAP SCREW, 3/8"-24 X 5/8" HEX HD CAP SCREW, 1/2"-13 X 1-1/2" HEX HD CAP SCREW, 1/2"-13 X 2-1/4" HEX HD CAP SCREW, 5/8"-11 X 2" HEX HD CAP NUT, 1/4"-20 HEX NYLOK NUT, 1/2"-13 HEX NUT, 1/2"-13 HEX NYLOK NUT, 5/8"-11 HEX NYLOK WASHER, 1/4" FLAT LOCKWASHER, 1/4" HELICAL WASHER, 5/16" FLAT WASHER, I.D. X O.D. X WASHER, 3/8" FLAT LOCKWASHER, 3/8" HELICAL LOCKWASHER, 1/2" HELICAL WASHER, 1/2" FLAT CONNECTOR, 3/8" TUBE X 1/8" NPT BULKHEAD COUPLING, 1/8" ELBOW, 1/4" NPT X 3/8" TUBE RETAINING RING, 1-1/4" NOM HEAVY DUTY FLANGE BEARING NYLATRON PAD FRONT PIN REAR PIN PIN, MAIN BOOM PIVOT PLATE, PAD CAGE PLATE, PAD CAGE LUBRICATOR MOUNTING PLATE WASHER PLATE, 14K CABLE WING PIN WELDMENT PIN WELDMENT BOOM WELDMENT, MAIN RECOVERY BRACKET WELDMENT INNER BOOM WELDMENT SHEAVE WELDMENT, SWIVEL GUIDE WELDMENT BOOM EXTENSION CYLINDER CYLINDER, BOOM LIFT WINCH, 15K DP NYLATRON PAD SCREW, 1/2"-13 X 3" HEX HD CAP FULL THRD VI-7

10 UNDERLIFT ASSEMBLY VI-8

11 UNDERLIFT ASSEMBLY GREASE FITTING,1/4"-28 STRAIGHT SCREW, 3/8"-16 X 1" HEX HD CAP GR SCREW, 3/8"-16 X 3" HEX HD CAP GR NUT, 3/8"-16 HEX NYLOK WASHER, 3/8" FLAT LOCKWASHER, 3/8" HELICAL RETAINING RING, 1-1/2" HEAVY DUTY PIN, STINGER PIN, FOLD CYLINDER BASE PIN WELDMENT CYLINDER, UNDERLIFT FOLD UNDERLIFT BOOM ASSEMBLY GREASE FITTING,1/4"-28 STRAIGHT SCREW, 3/8"-16 X 3/4" HEX HD CAP GR SCREW, 1/2"-20 X 1-1/4" HEX HD CAP GR LOCKWASHER, 3/8" HELICAL LOCKWASHER, 1/2" HELICAL WASHER, 1/2" FLAT RETAINING RING, 1-1/4" NOM HEAVY DUTY RETAINING RING, 1-1/4" NOM INT NYLATRON PAD FRONT PIN PIN, UNDERLIFT EXT (ROD) PLATE, CROSSBAR POSITIONING BAR, SPACER PLATE, U/L PAD CAGE U/L OUTER BOOM WELDMENT U/L INNER BOOM WELDMENT CYLINDER, UNDERLIFT EXTEND CROSSBAR ASSEMBLY SCREW, 3/8"-16 X 1-1/2" HEX SKT SET NUT, 3/8"-16 HEX NYLOK WASHER, 3/8" FLAT LOCKWASHER, 3/8" HELICAL CROSSBAR ASSEMBLY (cont'd) CROSSBAR END ASSEMBLY, LH CROSSBAR END ASSEMBLY, RH SCREW, 3/8"-16 X 1" HEX HD CAP GR DIE SPRING BALL, 1" CHROME RETAINING RING, 1-1/2" HEAVY DUTY PIN WELDMENT, CROSSBAR PIVOT CROSSBAR WELDMENT SPACER, CROSSBAR DIE SPRING CROSSBAR KIT, V GREASE FITTING, 1/4"-28 STRAIGHT WASHER, 5/8" FLAT ROLL PIN, 3/16" X 1" SLIDE LOCK HANDLE KNOB ASSEMBLY RUBBER HAND GRIP SCREW, 5/8"-11 X 1-1/2" HEX HD CAP GR FRONT STOP PIN ASSEMBLY SCOOP RETAINING PIN SCOOP WASHER SCOOP BRACKET WELDMENT, LH SCOOP BRACKET WELDMENT, RH OUTER CROSSTUBE, LT OUTER CROSSTUBE, RT CAR RETAINER KIT SCREW, 1/2"-13 X 6" HEX HD CAP WASHER, 1/2" FLAT WHEEL SPACER WELDMENT LIGHT WHEEL RETAINER, LH LIGHT WHEEL RETAINER, RH WHEEL RETAINER, LH WHEEL RETAINER, RH VI-9

12 RECOVERY BOOM HYDRAULICS VI-10

13 RECOVERY BOOM HYDRAULICS RECOVERY BOOM ASSEMBLY CONNECTOR, 6MJ-6MB HOSE ASSEMBLY, 44" BOOM EXTENSION CYLINDER LIFT CYLINDER CONNECTOR, 6MJ-6MB HOSE ASSEMBLY, 24" HOSE ASSEMBLY, 24" BULKHEAD RUN TEE, 6MJ-6BLKHD-6MJ W/NUT CYLINDER, BOOM LIFT MANUAL VALVE ASSEMBLY CONNECTOR, 6MJ-10MB HOSE ASSEMBLY, 44" HOSE ASSEMBLY, 29" BULKHEAD BRACKET WELDMENT (N.S.) VALVE, P70 VI-11

14 UNDERLIFT HYDRAULICS VI-12

15 UNDERLIFT HYDRAULICS RECOVERY BOOM ASSEMBLY CONNECTOR, 6MJ-6MB HOSE ASSEMBLY, 18" ADAPTER, 8MJ-6MJ HOSE ASSEMBLY, 75" CYLINDER, UNDERLIFT TILT TUBE ASSEMBLY, UNDER BOOM CLAMP SET, 4-TUBE UNDERLIFT BOOM ASSEMBLY CONNECTOR, 6MJ-6MB CYLINDER, UNDERLIFT EXTEND MANUAL VALVE ASSEMBLY CONNECTOR, 6MJ-10MB HOSE ASSEMBLY, 44" VALVE, P70 VI-13

16 PUMP, VALVE & FILTER HYDRAULICS VI-14

17 PUMP, VALVE & FILTER HYDRAULICS HOSE ASSEMBLY, 150" 2 28 FT SUCTION HOSE, 1-1/4" ID 100R HOSE ASSEMBLY, 120" PUMP, BI-ROTATIONAL KIT, PUMP FITTINGS HOSE CLAMP, 7/8" TO 2-3/4" ELBOW, 8MJ-12MB ADAPTER, 16MB-12FB HOSE BARB, 20HOSE-16MB SCREW, 1/2"-13 X 1-1/2" HEX HD CAP GR LOCKWASHER, 1/2" HELICAL KIT - HYD. TANK PARTS ELBOW, 16MB-16FB NIPPLE, 1" NPT X 3" LG NIPPLE, COMBINATION 1" NPT X 1-1/4" BARB 14 2 HC1338 BALL VALVE, 1" BRASS HYD. TANK ASSEMBLY ELBOW, 8MJ-12MP PIPE PLUG, 3/4" MAGNETIC SCREW, 5/16"-18 X 1" HEX HD CAP BREATHER CAP IMMERSION FILTER ASSEMBLY HYD. TANK WELDMENT MANUAL VALVE ASSEMBLY ELBOW, 8MJ-10MB HOSE ASSEMBLY, 53" CONNECTOR, 8MJ-10MB ELBOW, 8MJ-8MB HOSE ASSEMBLY, 25" CONNECTOR, 10MB-8FB SCREW, 3/8"-16 X 1" HEX HD CAP GR SCREW, 3/8"-16 X 1-1/2" HEX HD CAP GR NUT, 3/8"-16 NYLOK HEX WASHER, 3/8" FLAT PANEL - VALVE MOUNTING PANEL - VALVE COVER (NOT SHOWN) VALVE BRACKET WELDMENT VALVE, P70 VI-15

18 WINCH HYDRAULICS VI-16

19 WINCH HYDRAULICS 1 20 FT PLASTIC TUBING, 1/4" O.D FT CONVOLUTED LOOM, 1/4" MANUAL VALVE ASSEMBLY VALVE, SOLENOID AIR CONTROL HOSE ASSEMBLY, 72" CONNECTOR, 8MJ-10MB BREATHER VENT, 1/8 MP ELBOW, 1/4T-1/8MPX VALVE, P RECOVERY BOOM ASSEMBLY ELBOW, 8MJ-8MB BUSHING, HEX (BRASS) 4MP-2FP ELBOW, 1/4T-1/8MPX WINCH, 15K DP 15J VI-17

20 SPADE HYDRAULICS VI-18

21 SPADE HYDRAULICS HYDRAULIC TUBING ASSEMBLY ADAPTER, 8MJ-6MJ SCREW, 1/4"-20 X 1" HEX HD CAP (N.S.) NUT, 1/4"-20 HEX NYLOK (N.S.) WASHER, 1/4" FLAT (N.S.) HYDRAULIC TUBE ASSEMBLY TUBE CLAMP SET, 1/2" TUBE CLAMP SET, 1/2" BULKHEAD BRACKET WELDMENT (N.S.) JACK ASSEMBLY ADAPTER, 6MJ-6MBL CYL, HYD - JACKLEG HYD HOSE, 12" MANUAL VALVE ASSEMBLY ELBOW, 6MJ-6MB CONNECTOR, 6MJ-10MB HOSE ASSEMBLY, 44" HOSE ASSEMBLY, 29" CONNECTOR, 10MB-6FB VALVE, P70 VI-19

22 MANUAL CONTROL ASSEMBLY VI-20

23 MANUAL CONTROL ASSEMBLY CONTROL KNOB, (IN/OUT) CONTROL KNOB, BOOM (UP/DOWN) CONTROL KNOB, JACK (UP/DOWN) CONTROL KNOB, BOOM (IN/OUT) GREASE FITTING, 1/4"-28 X CONTROL KNOB, TILT (UP/DOWN) CONTROL KNOB, W/L EXTEND (IN/OUT) CONTROL KNOB, FOLD (UP/DOWN) SCREW, 5/16"-18 X 1-1/4" HEX HD CAP SCREW, 3/8"-16 X 1-3/4" HEX HD CAP NUT, 5/16"-18 HEX NUT, 3/8"-16 HEX JAM LOCKWASHER, 3/8" HELICAL CONTROL ASSEMBLY, LH MANUAL SCREW, 1/4"-20 X 1" HEX HD CAP NUT, 1/4"-20 HEX NYLOK SWITCH, MCGILL CONTROL CABLE, 6 FT CONTROL CABLE, 7 FT CONTROLS PIN, 12-3/4" CONTROLS PIN, 8-3/4" RETAINING BLOCK FRONT CONTROL BRACKET REAR CONTROL BRACKET 24 8 HD0900 BEARING ROD END, 1/4" CONTROL HANDLE ASSEMBLY FLANGED BEARING CONTROL HANDLE WELDMENT MANUAL VALVE ASSEMBLY CLEVIS, DUAL CONTROL CABLE VI-21

24 ELECTRIC CONTROL ASSEMBLY CONTROL PANEL ASSEMBLY SCREW, 1/4"-20 X 3/4" RD HD PH SS NUT, 1/4"-20 HEX NYLOK SCREW, 1/4"-20 X 1" HEX HD CAP SS WASHER, 1/4" FLAT SS NUT, 1/4"-20 HEX SS SWITCH, MCGILL DECAL, REMOTE PANEL, INTERFACE BOX CONTROL PANEL JOYSTICK MOUNTING PLATE ANGLE, RH SWITCH SWITCH ASSEMBLY (12) JOYSTICK CONTROL, DECAL, UP-OUT DECAL, IN-DOWN DECAL, FRONT WINCH DECAL, REAR WINCH KIT, CONTROL WIRING ASSEMBLY RELAY, SEALED & SKIRTED JUNCTION BOX, 18 PIN SCREW, 1/4"-20 X 1" RD HD PH NUT, 1/4"-20 HEX NYLOK LOCKWASHER, 3/8" EXT TOOTH VI-22

25 HYDRAULIC CYLINDERS CYLINDER, JACK LEG -- SEAL KIT, JACK LEG CYLINDER CYLINDER, BOOM EXTENSION -- SEAL KIT, BOOM EXTENSION CYLINDER CYLINDER, UNDERLIFT EXTEND -- SEAL KIT, UNDERLIFT EXTEND CYLINDER CYLINDER, BOOM LIFT -- SEAL KIT, BOOM LIFT CYLINDER CYLINDER, UNDERLIFT FOLD -- SEAL KIT, UNDERLIFT FOLD CYLINDER VI-23

26 LIFT FORKS & HOLDERS FORK, SHORT (3" OPENING) FORK, MEDIUM (3" OPENING) FORK, LONG (3" OPENING) FORK HOLDER WELDMENT, LH FORK HOLDER WELDMENT, RH VI-24

27 V30 PARTS SHIP KIT SAFETY WALK, 18" X 20' NAME PLATE, VULCAN BODY WIRING KIT, V30 SS CABLE TIE JUNCTION BOX, 10 POLE BULLET CONNECTOR, VINYL WIRING HARNESS, BODY WIRING HARNESS, FRONT MARKER WIRING HARNESS, BODY EXTENSION WIRING HARNESS, STOP & TURN WIRING HARNESS, MARKER SCHEMATIC, TOOLBOX WIRING SCHEMATIC, TOOLBOX WIRING 9 6 GV57 RUBBER GROMMET CONTROL PANEL KIT, V30 MANUAL 10 FT PLASTIC TUBING, 1/4 O.D. BLACK NIPPLE, 4MP-4MP HEX AIR FILTER/REGULATOR COMBO AIR LUBRICATOR MOUNTING BRACKET UNION, CONVERSION 1/4" X 6MM CONNECTOR, 1/4" TUBE X 1/4" MP PANEL, LH CONTROL SCHEMATIC, LH CONTROL WIRING DECAL, LH REAR LOWER DECAL, LH REAR UPPER DECAL, LH FRONT LOWER DECAL, LH FRONT UPPER PLASTIC TUBING, AIR LINE 6 MM 1 HA0132 GAUGE, PSI VI-25

28 3016 COMMON PARTS SHIP KIT SHIP KIT, 3014 COMMON PARTS LICENSE PLATE BRACKET CABLE TIE, 15-1/4" BLACK LICENSE PLATE ILLUMINATOR LIGHT, 3 BAR TIE DOWN STRAP, 15" SKUFF PAD, SAFETY CHAIN CABLE TIE DECAL, SAFETY CHAIN WARNING DECAL, RETRACT CAUTION DECAL, DANGER WHEEL LIFT ASSEMBLY HOSE MOUNTING HARDWARE KIT CABLE TIE, 15-1/4" BLACK CLAMP, 1" HOSE INSULATED CLAMP, 1-1/2" HOSE SCREW, 1/4"-20 X 1-1/2" RD HD SLOTTED NUT, 1/4"-20 HEX WASHER, 1/4" FLAT LOCKWASHER, 1/4" HELICAL DASH MOUNT CABLECN HARDWARE KIT SCREW, 1/4"-20 X 3/4" MACH NUT, 1/4"-20 HEX LOCKWASHER, 1/4" HELICAL SWITCH PANEL, MASTER ON/OFF BACK UP ALARM KIT 22 2 FT WIRE, 16 GA RED CONNECTOR, WIRE HEAT SHRINK TUBE, 1/4" BACK UP ALARM SCREW, 1/4"-20 X 1-1/4" HEX HD CAP NUT, 1/4"-20 HEX NYLOK INSTALL. INSTRUCTION, BACK UP ALARM VI-26

29 3016 COMMON PARTS SHIP KIT (cont'd) PLASTIC PLUG, 2-3/4" CHASSIS INSTALLATION KIT SCREW, 5/8"-11 X 2" HEX HD CAP NUT, 1/2"-13 HEX NYLOK NUT, 5/8"-11 HEX NYLOK WASHER, 1/2" FLAT WASHER, 5/8" EX THK FLAT CHASSIS INSTALLATION SHEET MOUNTING ANGLE, CENTER BODY FRONT MOUNT REAR MOUNTING BRACKET, FORD REAR MOUNTING BRACKET, STERLING SCREW, 1/2"-13 X 2-1/4" HEX HD CAP BODY INSTALLATION KIT SCREW, 1/2"-13 X 1-1/4" HEX HD CAP SCREW, 1/2"-13 X 4" HEX HD CAP NUT, 1/2"-13 HEX NYLOK WASHER, 1/2" FLAT LOCKWASHER, 1/2" HELICAL WASHER, 1/2" ID X 2" OD X SCREW, 1/2"-13 X 4-1/2" HEX HD CAP TOOLBOX MOUNTING PAD BOX MOUNTING TUBE BRACKET, BODY TUBE VI-27

30 NOTES

31 8503 Hilltop Drive Ooltewah, Tennessee (423)