MD616T INSTALLATION, OPERATION, MAINTENANCE & PARTS

Transcription

1 OWNER'S MANUAL MD616T INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice. All ratings specified are based on structural factors only, not vehicle capacities or capabilities. Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee FORM NO / 99 Phone (423) FAX (423) PRICE $25.00

2 LIMITED WARRANTY MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in material and workmanship for a period of twelve (12) months from date placed in service, but in no event shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve (12) months from date placed in service, whichever is earlier. MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or alterations have been made unless authorized by MILLER. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages concerning or relating to any product or parts, whether based on negligence, strict liability, breach of contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss resulted from any general or particular requirement which MILLER knew or had reason to know about at the time of sale. MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted under applicable law, pass on to the purchaser such manufacturer's or seller's warranty. MILLER, whose policy is one of continuous improvement, reserves the right to improve its products through changes in design or materials as it may deem desirable without being obligated to incorporate such changes in products previously sold. This warranty is not intended to cover or include the following items, which are set forth by way of example and not limitation: A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to weather, road conditions, road treatments, etc. B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure to provide reasonable and necessary maintenance, or uses for which the equipment was not designed or intended. C. Alterations or modifications that affect performance, operation or reliability. D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts. IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY OTHER IMPROPER USE. Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee SERIAL NUMBER Telephone (423)

3 Section VI - PARTS This Section is provided by the manufacturer for the purpose of ordering any component part of the HOLMES MD 616T that may be required when part replacement is necessary. Be certain to use only original equipment replacement parts for warranty purposes as well as for keeping your HOLMES MD 616T in its original state and optimum operating capacities. When ordering replacement or spare parts be sure to provide the following information to the manufacturer s Parts Department. 1. Manual Number & Date of Publication 2. Manual Page Number 3. Page Title 4. Reference Number of Part Desired 5. Part Number 6. Part Description 7. Quantity of Part Desired Providing this information will help ensure that the correct parts will be delivered to you in an expedient manner. Should additional information be required for repair or replacement of certain components, contact your Wrecker Manufacturer Authorized Representative. The Manufacturer reserves the right, without notice or obligation, to improve or modify their products, which may change the specifications, models and feature availability. VI-

4 84" C.A. BODY ASSEMBLY VI-2

5 84" C.A. BODY ASSEMBLY SPRING, PLUNGER RING, SNAP 1" HANDLE, PLUNGER "T" MUD FLAP LIGHT, RED GROMMET, LIGHT MOUNTING W/PLUG MARKER, SEALED RED MARKER, SEALED YELLOW 9 FT FLEXIBLE TRIM HOLD BACK, DOOR CHECK LIGHT, WHITE BACK-UP CLAMP LATCH, TOOL COMPARTMENT DOOR CHAIN, SAFETY HINGE, DOOR DOOR, TOOL BOX (ORDER BY SIZE) SCREW, #8-32 RD HD SCREW, 1/4"-20 X 1/2" HEX HD CAP SCREW, 1/4"-20 x 3/4" HEX HD CAP SCREW, 1/4"-20 X 1" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SCREW, 3/8"-16 X 1-1/2" HEX SKT SET SCREW, 1/2"-13 X 1-1/2" HEX HD CAP SCREW, 5/8"-11 X 2-1/4" HEX HD CAP NUT, #8-32 KEPS NUT, 1/4"-20 HEX NYLOK NUT, 1/4" "J" TINNERMAN NUT, 3/8"-16 NYLOK HEX NUT, 3/8"-16 HEX NYLOK NUT, LOCK 1/2" NUT, 5/8"-11 HEX NYLOK WASHER, LOCK 1/4" PIN, ROLL PIN, ROLL RIVET, 1/4" ROD PLUNGER RUBBER FENDER BAR, MUD FLAP SPADE BLADE ANGLE, FRONT MOUNTING ANGLE, REAR MOUNTING MUD GUARD MUD GUARD, CONTROL CROSS SHAFT, UPPER SPADE SHAFT, LOWER SPADE ANGLE, TAILGATE MOUNTING RETAINING STRIP INNER SPADE TUBE (HYDRAULIC) SPADE, MANUAL REAR SPADE PAD BODY WELDMENT, 84" C.A SPADE PAD PIN ASSEMBLY VI-

6 108" C.A. BODY ASSEMBLY VI-4

7 108" C.A. BODY ASSEMBLY SPRING, PLUNGER RING, SNAP 1" HANDLE, PLUNGER "T" LIGHT, STOP & TURN (BUILT BEFORE 4/94) LIGHT, BACK-UP (BUILT BEFORE 4/94) MUDFLAP LIGHT, RED GROMMET, LIGHT MOUNTING W/PLUG MARKER, SEALED RED MARKER, SEALED YELLOW FLEXIBLE TRIM HOLDBACK, DOOR CHECK LIGHT, WHITE BACK-UP CLAMP LATCH, TOOL COMPARTMENT DOOR CHAIN, SAFETY HINGE, DOOR DOOR, TOOL BOX (ORDER BY SIZE) SCREW, #8-32 RD HD SCREW, 1/4"-20 X 1/2" HEX HD CAP SCREW, 1/4"-20 x 3/4" HEX HD CAP SCREW, 1/4"-20 X 1" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SCREW, 3/8"-16 X 1-1/2" HEX SKT SET SCREW, 1/2"-13 X 1-1/2" HEX HD CAP SCREW, 5/8"-11 X 2-1/4" HEX HD CAP NUT, #8-32 KEPS NUT, 1/4"-20 HEX NYLOK NUT, 1/4" "J" TINNERMAN NUT, 3/8"-16 NYLOK HEX NUT, 3/8"-16 HEX NYLOK NUT, LOCK 1/2" NUT, 5/8"-11 HEX NYLOK WASHER, LOCK 1/4" PIN, ROLL RIVET, 1/4" PIN, ROLL PIN, PLUNGER RUBBER FENDER BAR, MUDFLAP SPADE BLADE ANGLE, FRONT MOUNTING ANGLE, REAR MOUNTING MUD GUARD MUD GUARD, CONTROL CROSSROD SHAFT, UPPER SPADE SHAFT, LOWER SPADE ANGLE, TAILGATE MOUNTING RETAINING STRIP INNER SPADE TUBE (HYDRAULIC) SPADE, MANUAL REAR SPADE PAD BODY WELDMENT, 108" C.A SPADE PAD PIN ASSEMBLY VI-5

8 UNDERLIFT ASSEMBLY VI-6

9 UNDERLIFT ASSEMBLY GREASE FITTING COMPRESSION SPRING, CROSSBAR BALL, 1-3/16" DIA. STEEL SLIDE PAD BUSHING "O" RING, PIVOT PIN 7 REF LIFT CYLINDER 8 REF TILT CYLINDER, LEFT REF TILT CYLINDER, RIGHT THRUST WASHER, 1/8" THRUST WASHER, 1/16" SCREW, 5/16"-18 X 2-1/2" HEX HD CAP SCREW, 3/8"-24 X 5/8" HEX HD CAP SCREW, 3/8"-24 X 5/8" BUTTON HD SKT SCREW, 5/8"-11 X 2-1/2" HEX HD CAP SCREW, 5/8"-11 X 2" HEX HD CAP SCREW, 5/8"-11 X 2-1/4" HEX HD CAP SCREW, 5/8"-11 X 4-1/2" SKT HD CAP NUT, 5/16"-18 NYLOK HEX NUT, 3/8"-16 NYLOK HEX NUT, 5/8"-11 NYLOK HEX LOCKWASHER, 3/8" EXT. TOOTH WASHER, 5/8" X 1-3/4" FLAT LOCKWASHER, 5/8" HELICAL STOP BLOCK, 2ND STAGE STOP PLATE PIN, EXTEND CYLINDER, BASE END SPACER PAD PIVOT PIN, TOP HALF PIVOT PIN, BOTTOM HALF PIN, UPPER LINK & LIFT CYLINDER SPACER, DETENT SPRING BOOM WELDMENT, 2ND STAGE BOOM WELDMENT, 3RD STAGE CROSSBAR WELDMENT OUTER BOOM WELDMENT FRAME WELDMENT 37 9 DE496 SCREW, 3/8"-16 X 3-3/4" HEX HD CAPP 38 1 HD55 IN, CYLINDER BASE 39 2 HD58 UPPER LINK ARM WELDMENT 40 4 HD59 BEARING, LINK UPPER 41 2 HD67B PIN, UPPER LINK 42 4 HD68B PIN, LOWER LINK 43 1 HD86 EXTEND CYLINDER PIN WELDMENT 44 1 HD89 RETAINING RING, 1-5/16" 45 REF. HD130 CYLINDER, BOOM EXTENSION VI-7

10 UNDERLIFT HYDRAULICS VI-8

11 UNDERLIFT HYDRAULICS VALVE, 4 SPOOL CONNECTOR, 6MJ-8MB ELBOW, 8MJ-10MB HOSEBARB, 12C4-12MP CLAMP, HOSE 1" GREASE FITTING HOSE ASSEMBLY, 91" H.P BRANCH TEE, 6MJ-6MJ-4MP ELBOW, 6MJ-6MP CLAMP, CHECK VALVE RETAINING, 7" ELBOW, STREET, 12MB-12FP TEE, 6MJ-6MJ-6MJ HOSE ASSEMBLY, 18" CONNECTOR, 6MJ-6MB BLACK HOSE "SKUFF" JACKET ELBOW, 6MJ-6MB FT RETURN HOSE, 3/4" VALVE, 5 SPOOL HOLDING VALVE, 3000 PSI HOSE ASSEMBLY, 45" LIFT CYLINDER TILT CYLINDER, LEFT TILT CYLINDER, RIGHT TUBE ASSEMBLY, LIFT CYLINDER HOSE ASSEMBLY, 104" HOSE ASSEMBLY, 75" HOSE ASSEMBLY, 111" SCREW, 1/4"-20 X 1-3/4" RD HD SCREW, 3/8"-16 X 4" HEX HD CAP NUT, 1/4"-20 NYLOK HEX NUT, 3/8"-16 NYLOK HEX BRACKET, HOLDING VALVE 33 1 HD130 CYLINDER, BOOM EXTEND VI-

12 OUTER CROSSTUBE & LIFT ADAPTERS VI-10

13 OUTER CROSSTUBE & LIFT ADAPTERS GREASE FITTING KNOB, "L" BAR LOCK CONTROL SPRING, PLUNGER PIN EXTENSION, TIRE RESTRAINT TIRE RESTRAINT BOLT, 5/8"-11 X 4-1/2" CARRIAGE NUT, 3/8"-16 HEX JAM NUT, 5/8"-11 HEX NYLOK WASHER, 5/8" FLAT PIN, 3/16" X 1" ROLL PIN, 5/32" X 1" ROLL PIN, PLUNGER HANDLE, "T" BRACKET, RESTRAINT ASSEMBLY PIVOT HANDLE, L.H. PLUNGER PIN HANDLE, R.H. PLUNGER PIN CROSSBAR, LEFT OUTER CROSSBAR, RIGHT OUTER ADAPTER, L.H. LIFT FORK OFFSET ADAPTER, R.H. LIFT FORK OFFSET RESTRAINT, TIRE MEDIUM FORK, SHORT (3" OPENING) FORK, MEDIUM (3" OPENING) FORK, LONG (3" OPENING) VI-11

14 WRECKER ASSEMBLY VI-12

15 WRECKER ASSEMBLY GREASE FITTING GREASE FITTING PAD, BOOM SLIDE RING, RETAINING WINCH, H-600 LT WINCH, H-600 RT WINCH, CABLE ASSEMBLY SCREW, 1/4"-20 X 5/8" HEX HD CAP SCREW, 3/8"-16 X 3" HEX HD CAP SCREW, 7/16"-14 X 1-1/4" HEX HD CAP SCREW, 5/8"-11 X 2-1/4" HEX HD CAP NUT, 3/8"-16 HEX NYLOK NUT, 5/8"-11 HEX NYLOK LOCKWASHER, 1/4" LOCKWASHER, 7/16" WASHER, 5/8" FLAT PIN, ROLL RETAINER, SLIDE PAD SHAFT, BOOM PIVOT SHAFT, LIFT CYLINDER SHAFT, LIFT CYLINDER SHAFT, EXTEND CYLINDER SHAFT, EXTEND CYLINDER SHIM, WINCH MTG DIPSTICK, RESE0RVOIR BOOM, OUTER BOOM, INNER FRAME, 716 WRECKER SWIVEL ASSEMBLY, BOOM END LEFT SWIVEL ASSEMBLY, BOOM END RIGHT VI-13

16 BOOM ELEVATION HYDRAULICS CONNECTOR, 6MJ-8MB GREASE FITTING CYLINDER, BOOM LIFT HOSE ASS'Y, 42" VI-14

17 BOOM EXTENSION HYDRAULICS VALVE, CONTROL, 4 SPOOL CONNECTOR, 6MJ-8MB GREASE FITTING ELBOW, 6MJ-6MP HOSE ASSY, 64" CYLINDER, EXTENSION HOSE ASSY, 140" VI-15

18 WINCH MOTOR HYDRAULICS CONNECTOR, 8MJ-8MB ELBOW, 8MJ-10MB HOSE ASSY, MOTOR, 53" CONNECTOR, 8MJ-10MB MOTOR, HYD., CHAR-LYNN, # ELBOW, 8MJ-8FJX SCREW, 1/2"-13 X 1.25" SOCKET HEAD CAP LOCKWASHER, 1/2", HELICAL VI-16

19 WINCH CLUTCH CONTROL Section VI - PARTS (cont'd) HYDRAULIC WINCH ASSEMBLY SPRING, CLUTCH "T" HANDLE YOKE, ADJUSTABLE SCREW, 5/16"-18 X 1/2" SQ HD SET WASHER, 1/2" FLAT HD PIN, 1/2" X 1-1/2" COTTER PIN, 1/8" X 1-1/4" COTTER PIN, 5/32" X 1" ROLL BELL CRANK - WINCH CONTROL ROD, WINCH CONTROL MTG. CHANNEL - WINCH CONTROL VI-17

20 HYDRAULIC WINCH ASSEMBLY VI-18

21 HYDRAULIC WINCH ASSEMBLY ADAPTER SPRING, FLAT BUSHING BUSHING PLATE, CAM CLUTCH, JAW COVER COVER, BRAKE SHOE, DRAG BRAKE DRUM, GEAR, R.H HOUSING, BRAKE HOUSING, CLUTCH HOUSING, GEAR HUB, GEAR HUB, BRAKE KEY, SQ. END KEY, SQ. END KEY, RD. END KEY, RD. END KEY, BARTH PLATE, RETAINER SHAFT, DRUM, SHAFT, SHIFTER SHIFTER, HANDLE SPACER, DRUM SHIP STRAP WORM, R.H YOKE BALL, POPPET BALL, BRAKE BEARING, BALL BEARING, THRUST BUSHING BUSHING, COVER, ADAPTER CAP SCREW, 5/16-18 NC X 1" HEX HD GR CAP SCREW, 5/16-18 NC X 3/4" HEX HD GR. 5 NYLOK H/P CAP SCREW, 5/16-18 NC X 1" LG HEX HD GR. 5 NYLOK H/P CAP SCREW, 3/8-16 NC X 1-1/4" LG HEX HD GR CAP SCREW, 3/8-24 NF X 1" LG HEX HD GR. 5 NYLOK H/P CAP SCREW, 7/16-14 NC X 3/4" LG HEX HD GR CAP SCREW, 1/2-13 NC X 3/4" LG HEX HD C.P. GR CAP SCREW, 1/2-20 NF X 1-3/4" LG HEX HD GR.5 ALL-THD CAP SCREW, 5/16-18 NC X 1" LG HEX SOC HD CAP SCREW, 5/16-18 NC X 1" LG SOC BUTTON HD ND STRIP SCREW, POPPET 1/2-20 NF HD LESS DR SLOT SET SCREW, 3/8-16 NC X 1/2" LG HEX SOC HD SET SCREW, 5/16-18 NC X 1/2" LG SQ HD SET SCREW, 5/16-18 NC X 3/4" LG SQ HD NUT, JAM 1/2-20 NF HEX LOCKWASHER, 5/16" MED SECT LOCK WASHER, 3/8" MED SECT WASHER, FLAT 3/8" ALUM GASKET GASKET GASKET FITTING, LUBE FITTING, RELIEF QUAD, RING "O"-RING REDUCER PLUG, PIPE PLATE THREAD, SEAL SPRING SPRING SPRING SPRING WASHER, THRUST SPACER, BRAKE DISC VI-19

22 PUMP & FILTER HYDRAULICS VI-20

23 PUMP & FILTER HYDRAULICS ELBOW, 8MJ-10MB HOSE BARB, 12C4-12MP CLAMP, HOSE 1" FILTER ASSY, PARKER FILTER ELEMENT, SPIN-ON HOSE ASSY, HI PRESSURE 91" STREET ELBOW, 90, 1" CLAMP, HOSE, 1" - 2-1/4" PIPE PLUG, 3/4" STREET ELBOW, 1-1/2" HOSE BARB, 24C4-24MP FT SUCTION HOSE, 1-1/2" PIPE NIPPLE, 1-1/2" X 3" ELBOW, 12MB-12FP PUMP, TP16-150A-2N ELBOW, 8MJ-12MB HOSE, 3/4" RETURN VALVE, BRONZE BALL FLANGE FITTING VI-21

24 CONTROLS & CROSSRODS VI-22

25 CONTROLS & CROSSRODS GROMMET, SPLIT PLASTIC KNOB, WINCH CABLE IN-OUT KNOB, BOOM UP-DOWN KNOB, JACK UP-DOWN KNOB, BOOM EXTEND IN-OUT KNOB, WHEEL LIFT TILT UP-DOWN KNOB, WHEEL LIFT EXTEND IN-OUT KNOB, WHEEL LIFT LIFT UP-DOWN SCREW, 1/4"-20 X 1/2" HEX HD CAP CLIP, 1/4" "U" TYPE TINNERMAN NUT, 3/8"-16 HEX ESLOK JAM NUT, 3/8"-16 HEX JAMLOCK WASHER, 1/4" HELICAL PIN, 5/16" X 5/8" CLEVIS COTTERLESS PIN, 3/16" X 1-1/2" COTTER PIN, 1/8" X 3/4" COTTER EXTENSION, CONTROL ROD CROSS ROD, WHEEL LIFT CROSS ROD, WRECKER CROSS ROD, WHEEL LIFT CONTROL LEVER CHANNEL, CONTROL ROD BEARING ANGLE, CONTROL ROD BEARING CROSS ROD, CONTROL CROSS ROD, TILT ARM, CROSS CONTROL SHIFTER ROD, SHORT SHIFTER ROD, MEDIUM SHIFTER ROD, LONG VI-23

26 LIGHTING ACCESSORIES VI-24

27 LIGHTING ACCESSORIES LICENSE PLATE HOLDER RUBBER GROMMET LICENSE PLATE ILLUMINATOR WRECKER SPECIAL LIGHT SPOTLIGHT W/GASKET SCREW, #10-32 X.75" SELF-TAPPING SCREW, 1/4"-20 X 1.5" HEX HD CAP SCREW, 1/4"-20 X.75" PAN HD SCREW, 1/4"-20 X.75" THD CUT HEX HD SCREW, 3/8"-16 X 1.5" HEX HD CAP NUT, 1/4"-20 HEX PLAIN NUT, 1/4"-20 NYLOK HEX NUT, 3/8"-16 HEX HD NYLOK WASHER, LOCK, 1/4" WASHER, FLAT, 3/8" ANGLE, PYLON BASE REINFORCING GASKET, PYLON BASE, 22" PYLON GASKET, PYLON BASE, 26" PYLON GASKET, PYLON BASE, 29" PYLON GASKET, PYLON BASE, 33" PYLON GASKET, PYLON BASE, 36" PYLON GASKET, PYLON BASE, 40" PYLON GASKET, PYLON BASE, 42" PYLON GASKET, PYLON BASE, 45" PYLON ADAPTER, "T" BOLT LIGHT MOUNTING PYLON, 22" LIGHT MOUNTING PYLON, 26" LIGHT MOUNTING PYLON, 29" LIGHT MOUNTING PYLON, 33" LIGHT MOUNTING PYLON, 36" LIGHT MOUNTING PYLON, 40" LIGHT MOUNTING PYLON, 42" LIGHT MOUNTING PYLON, 45" BRACKET, LICENSE PLATE MOUNTING VI-25

28 HYDRAULIC CYLINDERS - WRECKER CYLINDER, BOOM LIFT (COMPLETE) KIT, BOOM LIFT CYLINDER SEAL CYLINDER, BOOM EXTEND (COMPLETE) KIT, BOOM EXTEND CYLINDER SEAL VI-26

29 HYDRAULIC CYLINDERS - UNDERLIFT CYLINDER, LIFT (COMPLETE) KIT, UNDERLIFT CYLINDER SEAL 1 1 HD130 CYLINDER, UNDERLIFT EXTEND (COMPLETE) 2 1 HD163 KIT, UNDERLIFT EXTEND CYLINDER SEAL VI-27

30 HYDRAULIC CYLINDERS - UNDERLIFT CYLINDER, LT TILT CYLINDER, RT TILT KIT, UNDERLIFT TILT CYL. SEAL (TEXAS) KIT, UNDERLIFT TILT CYL. SEAL (SOUTHERN) VI-28

31 BOOM END SWIVEL ASSEMBLY BOOM SWIVEL ASSEMBLY, LEFT (COMPLETE) BOOM SWIVEL ASSEMBLY, RIGHT (COMPLETE) GREASE FITTING SHEAVE, 8" DIA X 1-1/2" RIM SCREW, 3/8"-16 X 3" HEX HD CAP SCREW, 3/8"-16 X 2-1/2" HEX HD CAP NUT, 3/8"-16 NYLOK HEX CABLE GUIDE, BOTTOM SHAFT, SHEAVE CABLE GUIDE WELDMENT SWIVEL WELDMENT, LEFT SWIVEL WELDMENT, RIGHT VI-29

32 VERNIER THROTTLE CONTROL STOP COLLAR #516 (HD1255) THROTTLE CONTROL CABLE, 20' KIT, THROTTLE ATTACHMENT VI-30

33 REAR JACK HYDRAULICS VALVE, CONTROL, 4 SPOOL HOSE ASSY, 81-1/2" ELBOW, 6MJ-6FJX FITTING, 45, 8FP-8FP NIPPLE, BLACK PIPE, 1/2" SCH 80, 4-1/2" LG VALVE, CONTROL, 5 SPOOL CYLINDER, SPADE CONNECTOR, 6MJ-8MP VI-31

34 LIGHT KIT LIGHT, SEALED RED (STOP & TURN) LIGHT, SEALED CLEAR (BACKUP) TAIL LIGHT GROMMET & PLUG KIT MARKER LIGHT, SEALED RED MARKER LIGHT, SEALED AMBER GROMMET MOUNTING KIT W/PLUG VI-32

35 LIGHT KIT LICENSE PLATE ILLUMINATOR BULB, LICENSE PLATE ILLUMINATOR BAR, 3 - LIGHT LENS, 3 - LIGHT BAR BULB, MARKER LIGHT VI-33

36 NOTES

37 NOTES

38 Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee (423)