CENTURY 1060S / SDU3 INSTALLATION, OPERATION, MAINTENANCE & PARTS

Transcription

1 CENTURY L E G E N D A R Y L E A D E R S H I P OWNER'S MANUAL 1060S / SDU3 INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice All ratings specified are based on structural factors only, not vehicle capacities or capabilities. CENTURY Miller Industries Towing Equipment Inc Hilltop Drive FORM NO Ooltewah, Tennessee / 2006 Phone (423) FAX (423) PRICE $25.00

2 LIMITED WARRANTY MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in material and workmanship for a period of twelve (12) months from date placed in service, but in no event shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve (12) months from date placed in service, whichever is earlier. MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or alterations have been made unless authorized by MILLER. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages concerning or relating to any product or parts, whether based on negligence, strict liability, breach of contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss resulted from any general or particular requirement which MILLER knew or had reason to know about at the time of sale. MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted under applicable law, pass on to the purchaser such manufacturer's or seller's warranty. MILLER, whose policy is one of continuous improvement, reserves the right to improve its products through changes in design or materials as it may deem desirable without being obligated to incorporate such changes in products previously sold. This warranty is not intended to cover or include the following items, which are set forth by way of example and not limitation: A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to weather, road conditions, road treatments, etc. B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure to provide reasonable and necessary maintenance, or uses for which the equipment was not designed or intended. C. Alterations or modifications that affect performance, operation or reliability. D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts. IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY OTHER IMPROPER USE. Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee SERIAL NUMBER Telephone (423)

3 Section VI - PARTS This Section is provided by the manufacturer for the purpose of ordering any component part of the 1060S Recovery Unit and SDU/3 Underlift that may be required when part replacement is necessary. Be certain to use only original equipment replacement parts for warranty purposes as well as for keeping your 1060S Recovery Unit and SDU/3 Underlift in its original state and optimum operating capacities. When ordering replacement or spare parts be sure to provide the following information to the manufacturer s Parts Department. 1. Manual Number & Date of Publication 2. Manual Page Number 3. Page Title 4. Reference Number of Part Desired 5. Part Number 6. Part Description 7. Quantity of Part Desired Providing this information will help ensure that the correct parts will be delivered to you in an expedient manner. Should additional information be required for repair or replacement of certain components, contact your Wrecker Manufacturer Authorized Representative. The Manufacturer reserves the right, without notice or obligation, to improve or modify their products, which may change the specifications, models and feature availability. VI-

4 SUBFRAME ASSEMBLY VI-2

5 SUBFRAME ASSEMBLY SCREW, 1/2"-13 X 1-1/4" HEX HD CAP LOCKWASHER, 1/2" HELICAL OUTER TUBE REINFORCEMENT PLATE, WRAPPER TIE PLATE, WRAPPER SIDE REINFORCEMENT, OUTER TUBE SUBFRAME WELDMENT "D" RING KIT "D" RING, TOWING ROLL PIN, 3/8" X 2-1/2" 7 2 GA0215 PIN, "D" RING MOUNTING HARDWARE KIT (Not Shown) SCREW, 7/8"-9 X 3" HEX HD CAP NUT, 7/8"-9 HEX NYLOK MOUNTING KIT (Not Shown) ANGLE, 5" X 5" X 3/8" X 20' JACK LEG BRACKET, LEFT JACK LEG BRACKET, RIGHT BOOM / TAILGATE BUMPER KIT SLIDE PAD, BUMPER SCREW, 3/8"-16 X 3/4" FL HD SKT SAFETY CHAIN ASSEMBLY KIT SAFETY CHAIN - SYSTEM NUT, 5/8"-11 HEX NYLOK WASHER, 5/8" FLAT MODULAR MOUNTS KIT LOCKWASHER, 1/2" HELICAL ZP SCREW, 1/2"-13 X 1-1/4" HEX HD CAP GR MODULAR MOUNTS KIT (cont'd) TOOLBOX MOUNTING PAD TOOLBOX MOUNTING WASHER PLATE, SS REAR WASHER JACK COVER KIT, ROTATOR SCREW, 1/4"-20 X 1" HEX HD CAP NUT, 5/16"-18 "J" TINNERMAN LOCKWASHER, 1/4" HELICAL SCREW, 5/16"-18 X 1" HEX HD CAP SS LOCKWASHER, 5/16" HELICAL COVER, LT CHAIN BOX COVER, RT CHAIN BOX COVER, JACK MOUNTING ANGLE (Not Shown) SIDE "D" RING ASSEMBLY WASHER, HEAVY "D" RING SHAFT "D" RING, TOWING LOCKING PIN W/ CHAIN ROLL PIN, 3/8" X 2-1/2" 36 1 GA0215 PIN, "D" RING ACCESS COVER KIT NUT, 5/16"-18 "J" TINNERMAN SCREW, 5/16"-18 X 1" HEX HD CAP SS SCREW, 3/8"-16 X 1-1/2" HEX HD CAP SS LOCKWASHER, 5/16" HELICAL LOCKWASHER, 3/8" HELICAL 316 SS COVER, FRONT FLOOR PLATE FLOOR PLATE, REAR FLOOR PLATE, CENTER FLOOR PLATE, CENTER FRONT FLOOR PLATE, LEFT FRONT FLOOR PLATE, RIGHT FRONT COVER PLATE VI-

6 BODY ASSEMBLY VI-4

7 BODY ASSEMBLY 1 97 FT DOOR SEAL (Not Shown) ANGLE, MUDFLAP MOUNTING LEFT ANGLE, MUDFLAP MOUNTING RIGHT LIMIT SWITCH TOOL COMPARTMENT, LEFT TOOL COMPARTMENT, RIGHT SUPPORT STRAP MUDFLAP KIT MUDFLAP BAR, MUDFLAP MUDFLAP MOUNTING HARDWARE KIT SCREW, 3/8"-16 X 1-1/4" HEX HD CAP NUT, 3/8"-16 HEX NYLOK RUBBER FENDER KIT FT RUBBER FENDER WELL MATERIAL RIVET, 1/4" RETAINING STRIP, RUBBER FENDER DRIP RAIL KIT (Not Shown) DRIP RAIL EXTRUSION, 104" SCREW, #8-32 X 3/4" RD HD SLOTTED FRONT OUTRIGGER COVER KIT (Not Shown) SCREW, 3/8"-16 X 1-1/2" HEX HD CAP NUT, 3/8"-16 HEX NYLOK NUT, 3/8"-16 HEX JAM WASHER, 3/8" FLAT SCREW, 3/8"-16 X 2" SKT SET MOUNTING ANGLE, OUTRIGGER COVER FRONT OUTRIGGER COVER WELDMENT SS WIRE ROPE, 3/4" 6 X 37 IWRC GLASS TUBE LEV-O-GAGE II (Not Shown) CENTURY NAMEPLATE " ALUMINUM SADDLE BOX (Not Shown) FT DOOR SEAL SCREW, 5/16"-18 X 1" HEX HD CAP SCREW, 5/8"-11 X 2" HEX HD CAP SCREW, 1/2"-13 X 2" HEX HD CAP NUT, 1/2"-13 HEX NYLOK NUT, 5/8"-11 HEX NYLOK WASHER, 5/16" FLAT LOCKWASHER, 5/16" HELICAL WASHER, 1/2" FLAT SCREW, 3/8"-16 X 1" HEX HD CAP SS LOCKWASHER, 3/8" HELICAL SS BRACKET, CHAIN RACK ANGLE, MOUNTING FRAME MOUNTING FRAME WELDMENT TOOL BOX, 36" AL TUNNEL (ADJ. SHELVES) LIGHT PYLON KIT (Not Shown) BASIC ROTATOR LIGHT PYLON W/ROTARY JUNCTION BOX, 10 POLE ROTARY CONTACT ASSEMBLY, 16 CIRCUIT SCREW, 1/4"-20 X 1" HEX HD CAP NUT, 1/4"-20 HEX NYLOK SUPPORT, JUNCTION BOX " LIGHT PYLON KIT LICENSE PLATE BRACKET LICENSE PLATE ILLUMINATOR LIGHT, 3-BAR SCREW, 1/2"-13 X 1-1/2" HEX HD CAP NUT, 1/2"-13 HEX NYLOK " LIGHT PYLON WELDMENT PYLON MOUNTING BRACKET WELDMENT VI-5

8 SDU/3 ASSEMBLY VI-6

9 SDU/3 ASSEMBLY INSTALLATION SDU/2 FIX & ROT GREASE FITTING, 1/4" SNAP RING, EXTERNAL 2" GREASE FITTING, 1/4" SCREW, 3/4"-10 X 2-1/2" HEX HD CAP GR8 GD SCREW, 7/8"-9 X 3" HEX HD CAP GR8 GOLD NUT, 3/4"-10 NYLOK HEX ZP NUT, 7/8"-9 NYLOK HEX GR8 ZP PIN, MAIN PIVOT PLATE, PIVOT MOUNTING SHIM PLATE, PIVOT MOUNTING SHIM TILT CYLINDER MOUNTING BRACKET SUPPORT, LEFT PIVOT WELDMENT SUPPORT, RIGHT PIVOT WELDMENT 14 1 UK0126 PIN, TILT CYLINDER BASE END UNDERLIFT SDU/3 ASSY SNAP RING, 1" GREASE FITTING, 1/4"-28 STRAIGHT SNAP RING, EXTERNAL 2" GREASE FITTING, STR 1/8" NPT 19 6 FT HOSE, 3/8" OD SYNFLEX SLIDE PAD, BOOM SIDE CYLINDER, FOLD SLIDE PAD, SDU/2 U/L CYLINDER, TILT SDU/ SCREW, 3/8"-16 X 1" HEX HD CAP GR5 ZP SCREW, 1/2"-13 X 4-1/2" HEX HD CAP GR5 ZP SCREW, 5/8"-11 X 1" HEX HD CAP GR8 ZP NUT, 1/2"-13 NYLOK HEX ZP LOCKWASHER, 5/8" HELICAL ZP SHIM, SIDE PLATE, OUTER BOOM PIN PIN, PIVOT PIN, TILT CYLINDER PIN, FOLD CYLINDER PIN, LIFT CYLINDER MAST, SDU/3 OUTER WELDMENT MAST-SDU/3 INNER WELDMENT CONNECTOR-MALE 3/8TUBEX BULKHEAD COUPLING-1/8 P ELBOW-1/4NPT X 3/8TUBE SCREW, 3/8"-16 X 1" NC FLAT UNDERLIFT SDU/3 ASSY (cont d) UPPER WEAR PAD, RECOVERY 42 1 HC0159 CYLINDER, LIFT 43 2 HD0152 SNAP RING, 3" INTERNAL CROSSBAR ASSEMBLY, 5" COMP. SPRING, CROSSBAR, FI STEEL BALL, 1-3/16" DIA O-RING, PIVOT PIN THRUST WASHER, 1/8" THK THRUST WASHER, 1/16" THK SCREW, 5/8"-11 X 4-1/2" SKT HD CAP LOCKWASHER, 5/8" HELICAL ZP SPACER, DETENT BALL SPRING PIN, TOP HALF PIVOT PIN, BOTTOM HALF PIVOT CROSSBAR WELDMENT BOOM, SDU/3 HORTZ ASSY GREASE FITTING, 1/4"-28 STRAIGHT SLIDE PAD, HORIZ BOOM NYL SLIDE PAD, HORIZ BOOM BUSHING, STINGER CYLINDER, EXTEND SCREW, 3/8"-16 X 1-1/2" HEX SKT SET SCREW, 3/8"-24 X 3/4" HEX HD CAP GR5 ZP SCREW, 1/2"-13 X 1-1/4" SOCKET HD SCREW, 3/8"-24 X 5/8" BUTTON HEAD NUT, 3/8"-16 NYLOK HEX ZINC LOCKWASHER, 3/8" EXT. TOOTH PLATE, STOP PLATE, STOP BAR, RETRACT SHAFT, EXTEND CYLINDER SHAFT, EXTEND CYLINDER ND STAGE BOOM WELDMENT OUTER BOOM WELDMENT INNER BOOM ASSEMBLY BUSHING, PIVOT PIN DRIVE SCREW, #10 X 1/2" RD HD PAD, SLIDER INNER BOOM WELDMENT VI-7

10 SDU/3 LIFT & EXTEND HYDRAULICS (HUSCO) VI-8

11 SDU/3 LIFT & EXTEND HYDRAULICS (HUSCO) INSTALLATION, SDU/2 FIXED & ROTATOR HOSE ASSEMBLY, 24" CAP ADAPTER BULKHEAD RUN TEE HOSE ASSEMBLY, 75" HOSE TENSION KIT (NOT SHOWN) EYE BOLT, 1/4"-20 X 1-1/ SCREW, 1/2"-13 X 3-3/4" HEX HD CAP GR5 ZP NUT, 1/4"-20 HEX ZP NUT, 1/4"-20 NYLOK HEX ZP NUT, 1/2"-20 NYLOK PLATED WASHER, 1/4" FLAT ZP BRACKET, BULKHEAD PULLEY, HOSE TENSIONER BRACKET, HOSE TENSIONER PULLEY WASHER, HOSE TENSIONER PULLEY ANGLE, NYLON SHEAVE 16 2 AWS-1011-A SPRING CLAW UNDERLIFT ASSEMBLY, SDU/ HOSE CLAMP, 8" ELBOW, 6MJ-6MB HOSE ASSEMBLY, 24" UNDERLIFT ASSEMBLY, SDU/3 (cont'd) HOSE ASSEMBLY, 141" FT BLACK SKUFF JACKET SJ16 (NOT SHOWN) CONNECTOR, 4MB-6FB HOLDING VALVE, 4000 PSI SAE TUBE ASSY, 3/8" OD X.035" W X 3" SCREW, 1/4"-20 X 2" HEX HD CAP GR5 ZP NUT, 1/4"-20 NYLOK HEX ZP WASHER, 1/4" FLAT ZP MOUNTING BRACKET, CHECK VALVE RUN TEE, 6MJ-6MB-6MJ 30 1 HC0159 UNDERLIFT LIFT CYLINDER HORIZONTAL BOOM ASSEMBLY, SDU/ ELBOW, 6MJ-8MB UNDERLIFT EXTEND CYLINDER PROPORTIONAL CONTROL VALVE KIT CONNECTOR, 6MJ-8MB CONNECTOR, 6MJ-6MB CONNECTOR, 8MB-6FB VALVE, PROPORTIONAL CONTROL VALVE, PROPORTIONAL CONTROL VI-9

12 SDU/3 LIFT & EXTEND HYDRAULICS (PARKER) VI-10

13 SDU/3 LIFT & EXTEND HYDRAULICS (PARKER) INSTALLATION SDU/2 FIXED & ROTATOR HOSE ASSEMBLY, 24" CAP ADAPTER BULKHEAD RUN TEE HOSE ASSEMBLY, 75" HOSE TENSION KIT (NOT SHOWN) /4-20 X 1.12 EYE BOLT /2-13X3.75 HHCS GR5 ZP /4-20 HEX NUT ZP /4-20 NYLOK HEX NUT ZP /2-20 NYLOK NUT PLATED /4 FLATWASHER ZP BRACKET, BULKHEAD PULLEY, HOSE TENSIONER BRACKET, HOSE TENSIONER PULLEY WASHER, HOSE TENSIONER PULLEY ANGLE, NYLON SHEAVE 16 2 AWS-1011-A SPRING CLAW CONTROL VALVE ASSEMBLY, SDU/ CONNECTOR, 6MJ-8MB CONNECTOR, 6MJ-6MBL CONTROL VALVE ASSEMBLY, SDU/2 (cont'd) CONNECTOR, 8MB-6FB CONTROL VALVE, 4 SPOOL PARKER UNDERLIFT ASSEMBLY, SDU/ HOSE CLAMP, 8" ELBOW, 6MJ-6MB HOSE ASSEMBLY, 24" HOSE ASSEMBLY, 141" FT BLACK SKUFF JACKET SJ16 (NOT SHOWN) CONNECTOR, 4MB-6FB HOLDING VALVE, 4000 PSI SAE TUBE ASSY, 3/8" OD X.035" W X 3" SCREW, 1/4"-20 X 2" HEX HD CAP GR5 ZP NUT, 1/4"-20 NYLOK HEX ZP WASHER, 1/4" FLAT ZP MOUNTING BRACKET, CHECK VALVE RUN TEE, 6MJ-6MB-6MJ 34 1 HC0159 UNDERLIFT LIFT CYLINDER HORIZONTAL BOOM ASSEMBLY, SDU/ ELBOW, 6MJ-8MB UNDERLIFT EXTEND CYLINDER VI-11

14 SDU/3 TILT & FOLD HYDRAULICS (HUSCO) VI-12

15 SDU/3 TILT & FOLD HYDRAULICS (HUSCO) INSTALLATION SDU/2 FIXED & ROTATOR CONNECTOR, 6MJ-8MB ELBOW, 6MJ-8MB CONNECTOR, 6MJ-6MB BRANCH TEE, 6MJ-6MJ-6MB ELBOW, 6MJ-6FJX VALVE, DOUBLE HOLDING HOSE ASSEMBLY, 24" HOSE ASSEMBLY, 18" HOSE ASSEMBLY, 46" CONNECTOR, 4MB-6FB VALVE, HOLDING 4000 PSI SAE SCREW, 1/4"-20 X 2" HEX HD CAP GR5 ZP NUT, 1/4"-20 NYLOK HEX ZP WASHER, 1/4" FLAT ZP MOUNTING BRACKET, CHECK VALVE UNDERLIFT SDU/3 ASSY HOSE CLAMP, 7" ELBOW, 6MJ-6MB INLINE ORIFICE HOSE ASSEMBLY, 18" HOSE ASSEMBLY, 108" FT BLACK SKUFF JACKET SJ UNDERLIFT FOLD CYLINDER UNDERLIFT TILT CYLINDER SCREW, 1/4"-20 X 2" HEX HD CAP GR5 ZP NUT, 1/4"-20 NYLOK HEX ZP WASHER, 1/4" FLAT ZP PROPORTIONAL CONTROL VALVE KIT CONNECTOR, 6MJ-8MB CONNECTOR, 6MJ-6MB CONNECTOR, 8MB-6FB VALVE, PROPORTIONAL CONTROL VALVE, PROPORTIONAL CONTROL VI-13

16 SDU/3 TILT & FOLD HYDRAULICS (PARKER) VI-14

17 SDU/3 TILT & FOLD HYDRAULICS (PARKER) INSTALLATION SDU/2 FIXED & ROTATOR CONNECTOR, 6MJ-8MB ELBOW, 6MJ-8MB CONNECTOR, 6MJ-6MB BRANCH TEE, 6MJ-6MJ-6MB ELBOW, 6MJ-6FJX VALVE, DOUBLE HOLDING HOSE ASSEMBLY, 24" HOSE ASSEMBLY, 18" HOSE ASSEMBLY, 46" CONNECTOR, 4MB-6FB VALVE, HOLDING 4000 PSI SAE SCREW, 1/4"-20 X 2" HEX HD CAP GR5 ZP NUT, 1/4"-20 NYLOK HEX ZP WASHER, 1/4" FLAT ZP MOUNTING BRACKET, CHECK VALVE CONTROL VALVE ASSEMBLY, SDU/ CONNECTOR, 6MJ-8MB CONNECTOR, 6MJ-6MBL CONNECTOR, 8MB-6FB CONTROL VALVE, 4 SPOOL PARKER UNDERLIFT SDU/3 ASSY HOSE CLAMP, 7" ELBOW, 6MJ-6MB INLINE ORIFICE HOSE ASSEMBLY, 18" HOSE ASSEMBLY, 108" FT BLACK SKUFF JACKET SJ UNDERLIFT FOLD CYLINDER UNDERLIFT TILT CYLINDER SCREW, 1/4"-20 X 2" HEX HD CAP GR5 ZP NUT, 1/4"-20 NYLOK HEX ZP WASHER, 1/4" FLAT ZP VI-15

18 SDU/3 LIFT ADAPTERS VI-16

19 SDU/3 LIFT ADAPTERS TRAILER BALL, 2" 2 1 HD1259 SAFETY SNAP PIN 3 1 VA0662 PIVOT PIN WELDMENT STANDARD FORK KIT, SDU FORK, SHORT 3" OPENING FORK, SHORT 4-1/2" OPENING FORK, MEDIUM 3" OPENING FORK, MEDIUM 4-1/2" OPENING FORK, LONG 3" OPENING FORK, LONG 4-1/2" OPENING FORK, OFFSET REAR AXLE FORK, MEDIUM ROUND AXLE ALUM T HANDLE, 5/8" X 1-1/4" COTTER PIN, 1-1/4" HAIR PIN BOLT, MODIFIED HDU CHAIN ADAPTER, RT HDU CHAIN ADAPTER, LT PIVOT SPRING LIFT BRACKET FORK ADAPTER, LEFT FORK ADAPTER, RIGHT RETAINER PIN ASSEMBLY RETAINER PIN, SPRING LIFT PINTLE HOOK KIT PINTLE HOOK SCREW, 1/2"-13 X 1-1/4 HEX HD CAP GR5 ZP LOCKWASHER, 1/2" HELICAL ZP DECAL, SAFETY CHAIN WARNING TH WHEEL & KING PIN ADAPTER RETAINER PIN ASSEMBLY TRAILER BALL KIT SCREW, 1/2"-13 X 1-1/4 HEX HD CAP GR5 ZP LOCKWASHER, 1/2" HELICAL ZP TRAILER BALL BRACKET WELDMENT VI-17

20 ROTATOR PINLOCK ASSEMBLY VI-18

21 ROTATOR PINLOCK ASSEMBLY 1 25 FT PLASTIC TUBING, 1/4 O.D. BLK ADJUSABLE CLEVIS, 3/8" AC AIR CYLINDER, 1.5 BORE / 1.71 STROKE NYLON SPACER, 5/16" THK X 5/16"ID NUT, 3/8"-24 HEX ZP NUT, 7/16"-20 HEX JAM PL COTTER PIN, 3/32" X 1" COTTER PIN, 1/8" X 3/4" COTTER PIN CLEVIS PIN, 1/4" X 1-3/4" ZP CLEVIS PIN, 5/16" X 1-3/4" ZP CLEVIS PIN, 5/16" X 1-3/8" ZP WASHER, 5/16 FLAT 316SS ALLTHREAD CONNECTOR RETAINING PIN, HOUSE LOCK BAR LINK, PIN LOCK BAR LEVER, PIN LOCK HOUSE LOCK COVER WELDMENT CLEVIS WELDMENT PIN LOCK WELDMENT BRASS ELBOW, 1/4T-1/8MP VI-19

22 3-STAGE RECOVERY BOOM ASSEMBLY VI-20

23 3-STAGE RECOVERY BOOM ASSEMBLY SLEW RING, 1060S WRECKER MOUNTING KIT SCREW, 1"-8 X 3" SKT HD CAP SCREW, 1"-8 X 3" HEX HD CAP GR8 ZP SCREW, 1"-8 X 6-1/2" HEX HD CAP GR8 ZP WASHER, 1-1/16" X 2" X 1/8" FLAT ZP WASHER, 1-1/16" X 2-1/2" X 1/8" FLAT ZP WRECKER FRAME ASSEMBLY, 1060S SCREW, 1/4"-20 X 3/4" HEX HD CAP GR5 ZP SCREW, 1/2"-13 X 6" HEX HD CAP GR5 ZP NUT, 1/2"-13 NYLOK HEX ZP WASHER, 1/4" FLAT ZP LOCKWASHER, 1/4" HELICAL SHAFT, BOOM PLATE, ACCESS COVER ANGLE, MOUNTING LOCK WELDMENT WRECKER FRAME WELDMENT, 1060S STAGE BOOM ASSEMBLY GREASE FITTING,1/4"-28 STRAIGHT SLIDE PAD, BOOM BOTTOM SLIDE PAD, BOOM SIDE SLIDE PAD, BOOM SIDE INNER BOOM SLIDE PAD SLIDE PAD, 3/4" x 1" x 4" SLIDE PAD SCREW, 1/4"-20 X 3/4" HEX HD CAP GR5 ZP SCREW, 3/8"-16 X 3/4" HEX HD CAP GR5 ZP SCREW, 3/8"-16 X 1" HEX HD CAP GR5 ZP SCREW, 3/8"-16 X 3-1/2" HEX HD CAP GR5 ZP SCREW, 3/8"-16 X 7/8" HEX HD CAP GR5 ZP SCREW, 5/8"-11 X 1" HEX HD CAP GR5 ZP NUT, 3/8"-16 NYLOK HEX ZP WASHER, 1/4" FLAT ZP LOCKWASHER, 1/4" HELICAL ZP LOCKWASHER, 3/8" HELICAL ZP LOCKWASHER, 5/8" HELICAL ZP SHIM, SIDE PLATE, OUTER BOOM SHAFT, CYLINDER PIVOT PAD, SHIM WEAR TOP SPACER PLATE, SLIDE PAD SUPPORT SHIM, SLIDE PAD CABLE TIE BACK WELDMENT STAGE BOOM ASSEMBLY (cont'd) SECOND STAGE BOOM WELDMENT, 3 STAGE OUTER BOOM WELDMENT, 3 STAGE THIRD STAGE BOOM WELDMENT, 3 STAGE STAGE EXTENSION SYSTEM ASSEMBLY SNAP RING, PP SHAFT, EXTEND CYLINDER SCREW, 5/8" NC X 1-1/2" HEX HD CAP PL GR BOOM SWIVEL KIT ROLL PIN, 1/2" X 1-1/4" ZP BOOM SWIVEL ASSEMBLY WINCH CABLE STOW KIT SCREW, 5/8"-11 X 4" HEX HD CAP GR5 ZP NUT, 5/8"-11 NYLOK HEX ZP WELDLESS CHAIN LINK, 5/8" CABLE TIE BACK SPRING, 1" "D" RINGS, INNER & OUTER GREASE FITTING, 1/4"-28 STRAIGHT ROLL PIN, 3/8" X 1-3/4" ZP TOWING "D" RING PIN, "D" RING PIN, "D" RING LIFT CYLINDER KIT, GREASE FITTING, 1/4"-28 STRAIGHT CYLINDER, BOOM LIFT SCREW, 3/8"-16 X 4-1/2" HEX HD CAP GR8 ZP NUT, 3/8"-16 NYLOK HEX ZP SHAFT, LIFT CYLINDER PIVOT WINCH CABLE SUPPORT WING SCREW, 3/8"-16 X 1-1/4" HEX HD CAP GR5 ZP SCREW, 3/8"-16 X 7/8" HEX HD CAP GR5 ZP LOCKWASHER, 3/8" HELICAL ZP CABLE WING, LONG 1040 & 1040B CABLE WING, MEDIUM 1040 & 1040B WINCH KIT, DP50K SSPD WKR ROT WINCH, DP S50 50K SINGLE SPD SCREW, 3/4"-10 X 3-1/2" HEX HD CAP GR8 ZP SCREW, 3/4"-10 X 5" HEX HD CAP GR5 ZP NUT, 3/4"-10 NYLOK HEX GR8 ZP WASHER, 3/4" FLAT ZP ANGLE, WINCH MOUNTING VI-21

24 3-STAGE EXTENSION SYSTEM ASSEMBLY VI-22

25 3-STAGE EXTENSION SYSTEM ASSEMBLY STAGE EXTENSION SYSTEM ASSEMBLY GREASE FITTING,1/4"-28 STRAIGHT SHEAVE, 10" DIA. X 1-1/2" BORE EXTEND CABLE ASSEMBLY RETRACT CABLE ASSEMBLY BOOM EXTEND CYLINDER, 1060S 3-STAGE SCREW, 1/2"-13 X 3/4" HEX HD CAP GR SCREW, 5/8"-11 X 2-1/4" HEX HD CAP GR5 ZP NUT, 5/8"-11 NYLOK HEX ZP NUT, 1-1/4"-12 HEX JAM NUT, 1-1/4"-12 HEX GR8 PL LOCKWASHER, 1/2" HELICAL ZP WASHER, 1-1/4" SAE HARDENED PL PIN, EXTEND CABLE PIN, RETRACT CABLE SHAFT, RETRACT SHEAVE WELDMENT 16 4 HD0167 SNAP RING, 1-3/8" EXTERNAL EXTEND SHEAVE SUBASSEMBLY GREASE FITTING,1/4"-28 STRAIGHT SHEAVE, 10" DIA. X 1-1/2" BORE SCREW, 1/2"-13 X 1-1/4" HEX HD CAP GR5 ZP SCREW, 1/2"-13 X 1-1/2" HEX HD CAP GR5 ZP SCREW, 1/2"-13 X 3/4" HEX HD CAP GR NUT, 1/2"-13 NYLOK HEX ZP LOCKWASHER, 1/2" HELICAL ZP ROD, EXTEND SHEAVE SPACER BAR, KICK SHAFT, EXTEND SHEAVE WELDMENT EXTEND SHEAVE BRACKET WELDMENT VI-23

26 2-STAGE RECOVERY BOOM ASSEMBLY VI-24

27 2-STAGE RECOVERY BOOM ASSEMBLY GREASE FITTING SNAP RING WIRE ROPE, 6 X 37 IWRC, 3/4" X 250 FT SLIDE PAD, BOOM BOTTOM SLIDE PAD, BOOM SIDE ANCHOR SHACKLE, 1-1/2" SLIDE PAD, INNER BOOM BOOM LIFT CYLINDER SLEW RING WINCH, DP S50-50K (Not Shown) SLIDE PAD, BOOM SIDE BOOM EXTEND CYLINDER SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SCREW, 3/8"-16 X 1" HEX HD CAP SCREW, 3/8"-16 X 3-1/2" HEX HD CAP SCREW, 3/8"-16 X 7/8" HEX HD CAP SCREW, 3/8"-16 X 4-1/2" HEX HD CAP SCREW, 5/8"-11 X 4" HEX HD CAP SCREW, 1/2"-13 X 6" HEX HD CAP SCREW, 5/8"-11 X 1" HEX HD CAP SCREW, 3/4"-10 X 5" HEX HD CAP SCREW, 1"-8 X 3" SKT HD CAP SCREW, 1"-8 X 3" HEX HD CAP SCREW, 1"-8 X 6-1/2" HEX HD CAP NUT, 3/8"-16 HEX NYLOK NUT, 1/2"-13 HEX NYLOK NUT, 5/8"-11 HEX NYLOK NUT, 3/4"-10 NYLOK HEX LOCKWASHER, 3/8" HELICAL LOCKWASHER, 5/8" HELICAL WASHER, 1-1/16 X 2 X 1/8" HARDENED WASHER, 1-1/16 X 2-1/2 X 1/8" HARDENED ROLL PIN, 1/2" X 1-1/4" ROLL PIN, 3/8" X 1-3/4" SHIM, SIDE PLATE, OUTER BOOM SHAFT, LIFT CYLINDER PIVOT SHAFT, BOOM PIVOT CABLE WING, MEDIUM TOP SPACER, OUTER BOOM PLATE, ACCESS COVER (Not Shown) SHAFT, EXTEND CYLINDER, ROD END SHAFT, EXTEND CYLINDER, BASE END CABLE WING, LONG "D" RING PIN, INNER BOOM "D" RING PIN, OUTER BOOM ANGLE, WINCH MOUNTING (Not Shown) SHAFT, LIFT CYLINDER LOWER PIVOT LOCK WELDMENT RECOVERY FRAME WELDMENT, 1060S OUTER BOOM WELDMENT INNER BOOM WELDMENT BOOM SWIVEL ASSEMBLY WELDLESS CHAIN LINK, 5/8" SPRING, CABLE TIE-BACK 55 4 MM12B RING, TOWING VI-25

28 3-STAGE RECOVERY BOOM HYDRAULICS VI-26

29 3-STAGE RECOVERY BOOM HYDRAULICS HYDRAULIC ROTARY SWIVEL ASSEMBLY HYDRAULIC SWIVEL CONNECTOR, 8MJ-8MB HOSE ASSEMBLY, LIFT CYLINDER, 64" EXTENDED CONNECTOR, 8MJ-8MBL HOSE ASSEMBLY, 30" LIFT CYLINDER KIT, CONNECTOR, 8MJ-8MB GREASE FITTING HOSE CLAMP, 8" HOSE ASSEMBLY, 45" ELBOW, 8MB-8TB ELBOW, 8MJ-8MB EXTENDED CONNECTOR, 8MJ-8MBL RUN TEE, 8MJ-8MJ-8FJX HOSE ASSEMBLY, 34" HOLDING VALVE HOSE ASSEMBLY, 41" BRANCH TEE, 8MB-8TB-8TB CYLINDER, BOOM LIFT SCREW, 3/8"-16 X 2-1/4" HEX HD CAP NUT, 3/8"-16 NYLOK HEX MOUNTING BRACKET, CHECK VALVE HYDRAULIC TUBE, ELEVATION CYLINDER HYDRAULIC TUBE, ELEVATION CYLINDER STAGE EXTENSION SYSTEM ASSEMBLY ELBOW, 8MJ-8MB CYLINDER, BOOM EXTEND 1060S 3-STAGE VI-27

30 2-STAGE RECOVERY BOOM HYDRAULICS VI-28

31 2-STAGE RECOVERY BOOM HYDRAULICS CONNECTOR, 8MJ-8MB GREASE FITTING HOSE CLAMP, 8" HOSE ASSEMBLY, 45" HOSE ASSEMBLY, 53" HOSE ASSEMBLY, 53" CONNECTOR, 8MJ-8MJ (Not Shown) ELBOW, 8MB-8TB ELBOW, 8MJ-8MB EXTENDED CONNECTOR, 8MJ-8MBL HOSE ASSEMBLY, 30" RUN TEE, 8MJ-8MJ-8FJX CYLINDER, BOOM LIFT HYDRAULIC SWIVEL HOLDING VALVE BRANCH TEE, 8MB-8TB-8TB CYLINDER, BOOM EXTEND SCREW, 3/8"-16 X 2-1/4" HEX HD CAP NUT, 3/8"-16 NYLOK HEX MOUNTING BRACKET, CHECK VALVE HYDRAULIC TUBE, ELEVATION CYLINDER HYDRAULIC TUBE, ELEVATION CYLINDER VI-29

32 WINCH HYDRAULICS & AIR FREE SPOOL VI-30

33 WINCH HYDRAULICS & AIR FREE SPOOL HYDRAULIC ROTARY SWIVEL ASSEMBLY ELBOW, 8MJ-8MB REDUCER, 8MB-4FP HYDRAULIC SWIVEL HOSE ASSEMBLY, 105" HOSE ASSEMBLY, 117" ELBOW, 1/4" T - 1/4" MP BRASS CONNECTOR, 1/4" T - 1/4" MP BRASS WINCH KIT, DP50K SSPD WKR ROT CONNECTOR, 8MJ-8MB RUBBER GROMMET ELBOW, 8MJ-8MB FT PLASTIC TUBING, 1/4" O.D. BLACK CABLE TIE, 4" FT CONVOLUTED LOOM, 1/4" WINCH, DP S50 50K SINGLE SPD ELBOW, 1/4" T - 1/4" MP BRASS AIR TENSIONER KIT FT PLASTIC TUBING, 1/4" O.D. BLACK CABLE TIE, 4" FT CONVOLUTED LOOM, 1/4" SCREW, 1/4"-20 X 3/4" THRD CUT HEX BULKHEAD BRACKET PLATE, HPDC MOUNTING ELBOW, 1/4" T - 1/4" MP BRASS VI-31

34 RECOVERY BOOM FRAME HYDRAULICS (HUSCO) VI-32

35 RECOVERY BOOM FRAME HYDRAULICS (HUSCO) HOSE ASSEMBLY, 53" HOSE ASSEMBLY, 65" HOSE ASSEMBLY, 41" HOSE ASSEMBLY, 50" HYDRAULIC ROTARY SWIVEL ASSEMBLY CONNECTOR, 8MJ-8MB ELBOW, 8MJ-8MB EXTENDED CONNECTOR, 8MJ-8MBL HOSE ASSEMBLY, 30" PLUG, 8MB HEX SKT (Not Shown) ELBOW, 8MJ-8MB90LL HYDRAULIC SWIVEL SCREW, 5/8"-11 X 2-3/4" HEX HD CAP NUT, 5/8"-11 NYLOK HEX PLANETARY GEAR REDUCER WITH BRAKE & MOTOR CONNECTOR, 8MJ-10MB HYDRAULIC MOTOR PLANETARY GEAR REDUCER BRAKE, SWING DRIVE SCREW, 1/2"-13 X 1" HEX HD CAP SCREW, 1/2"-13 X 1-1/2" SKT HD CAP GR PLANETARY GEAR REDUCER WITH BRAKE & MOTOR (cont'd) SCREW, 5/8"-11 X 2-1/2" HEX HD CAP LOCKWASHER, 1/2" HELICAL LOCKWASHER, 5/8" HELICAL 23 1 IC209 ADAPTER, 6MJ-4MB SWING VALVE KIT CONNECTOR, 8MJ-10MB HOSE ASSEMBLY, 15" HOSE ASSEMBLY, 22" SWING CONTROL VALVE NUT, 1/4"-20 NYLOK HEX SCREW, 1/4"-20 X 4-1/2" HEX HD CAP 30 1 HC1291 FITTING, 4MJ-4MB STR THR PROPORTIONAL CONTROL VALVE KIT CONNECTOR, 8MJ-8MB EXTENDED CONNECTOR, 8MJ-8MBL CONNECTOR, 10MJ-10MB CONNECTOR, 10MJ-8MB CONNECTOR, 8MB-10FB VALVE, PROPORTIONAL CONTROL VALVE, PROPORTIONAL CONTROL VI-33

36 RECOVERY BOOM FRAME HYDRAULICS (PARKER) VI-34

37 RECOVERY BOOM FRAME HYDRAULICS (PARKER) HOSE ASSEMBLY, 53" HOSE ASSEMBLY, 65" CONNECTOR, 8MJ-10MB EXTENDED CONNECTOR, 8MJ-8MBL CONTROL VALVE, VDP12CDD CONTROL VALVE, VDP12CDCD CONNECTOR, 10MJ-10MB CONNECTOR, 10MJ-10MBL CONNECTOR, 10MB-8FB HOSE ASSEMBLY, 41" HOSE ASSEMBLY, 50" HYDRAULIC ROTARY SWIVEL ASSEMBLY CONNECTOR, 8MJ-8MB ELBOW, 8MJ-8MB EXTENDED CONNECTOR, 8MJ-8MBL PLUG, 8MB HEX SKT (Not Shown) ELBOW, 8MJ-8MB90LL HYDRAULIC SWIVEL SCREW, 5/8"-11 X 2-3/4" HEX HD CAP NUT, 5/8"-11 NYLOK HEX PLANETARY GEAR REDUCER & HYDRAULIC MOTOR ASSEMBLY CONNECTOR, 8MJ-10MB PLANETARY GEAR REDUCER & HYDRAULIC MOTOR ASSEMBLY(cont'd) PLANETARY GEAR BOX PINION GEAR (Not Shown) HYDRAULIC MOTOR GEARBOX BRAKE SCREW, 1/2"-13 X 1" HEX HD CAP SCREW, 1/2"-20 X 1-3/4" SKT HD CAP SCREW, 5/8"-11 X 2-1/2" HEX HD CAP LOCKWASHER, 1/2" HELICAL LOCKWASHER, 5/8" HELICAL PINION RETAINER (Not Shown) 31 1 IC209 ADAPTER, 6MJ-4MB SWING VALVE KIT CONNECTOR, 8MJ-10MB HOSE ASSEMBLY, 30" HOSE ASSEMBLY, 15" HOSE ASSEMBLY, 22" SWING CONTROL VALVE NUT, 1/4"-20 NYLOK HEX SCREW, 1/4"-20 X 4-1/2" HEX HD CAP 39 1 HC1291 FITTING, 4MJ-4MB STR THR VI-35

38 PUMP, VALVE & FILTER HYDRAULICS (HUSCO) VI-36

39 PUMP, VALVE & FILTER HYDRAULICS (HUSCO) HOSE ASSEMBLY, 30" HOSE ASSEMBLY, 107" HOSE ASSEMBLY, 131" GAUGE, FLUSH MOUNT, 6000 PSI CONNECTOR, 6MJ-4FP PISTON PUMP, PARKER OUTRIGGER CONTROL VALVE KIT CONNECTOR, 6MJ-8MB ELBOW, 8MJ-10MB CONNECTOR, 8MJ-10MB HOSE ASSEMBLY, 91" HOSE ASSEMBLY, 92" OUTRIGGER CONTROL VALVE PISTON PUMP KIT HOSE CLAMP, 1" - 2-1/4" HOSE BARB, 2" FT SUCTION HOSE, 2" BRANCH TEE, 6MJ-6MJ-6MB ELBOW, 32-32FL90 W/ FLANGE KIT HOSE ASSEMBLY, 18" CLAMP, 2-1/2" INSULATED (Not Shown) ELBOW, 16MJ-20FL90 W/ FLANGE KIT HOSE ASSEMBLY, 120" BRACKET, HOSE (Not Shown) 23 2 IC209 ADAPTER, 4MB-6MJ FILTER CONVERSION OIL TANK KIT ELBOW, 8MJ-12MP CONNECTOR, 6MJ-4MP HOSE ASSEMBLY, 131" PIPE PLUG, 2" SQ HD TANK KIT BARB, 16C4-16MP FT SUCTION HOSE, 1" 16C RETURN LINE FILTER ASSEMBLY TANK KIT (cont'd) STREET ELBOW, 1" SIGHT GAGE, TYPE S BALL VALVE, BRONZE CENTER BONDED MOUNT SPECIAL WASHER PIPE NIPPLE, 2" X 4" REDUCER BUSHING, 1-1/2 MP TO 1 FP PIPE PLUG, 3/4" NPT MAGNETIC BUSHING, 1-1/2 MP TO 1-1/4 FP FILLER CAP FILTER ASSEMBLY, PARKER COVER PLATE GASKET, CLEANOUT & FILLER COVER RESERVOIR WELDMENT HOSE CLAMP, HS /4" PROPORTIONAL CONTROL VALVE KIT CONNECTOR, 12FJ-8MJ HOSE ASSEMBLY, 18" CONNECTOR, 6MJ-6MB ELBOW, 6MJ-6MB ELBOW, 6MJ-6FJX ADAPTER, 12MJ-10MB ELBOW, 12MJ-10MB BENT TUBE, SWIVEL 16C2-16FJX CONNECTOR, 6MJ-6MBL TEE, 12MJ-12FJX-12MJ ADAPTER, 12FJ-6MJ CONTROL VALVE, PROPORTIONAL CONNECTOR, 16MJ-10MB HOSE ASSEMBLY, 12" HOSE ASSEMBLY, 24" CONTROL VALVE, PROPORTIONAL 62 1 GB330 TEE, 12MJ-12MJ-12MJ 63 2 IC209 ELBOW, 4MB-6MJ IC212 STRAIGHT ADAPTER, 4MB-6MJ VI-37

40 PUMP, VALVE & FILTER HYDRAULICS (PARKER) VI-38

41 PUMP, VALVE & FILTER HYDRAULICS (PARKER) ELBOW, 8MJ-10MB HOSE BARB, 12C4-12MP BARB, 16C4-16MP CLAMP, HOSE, 1" RETURN LINE FILTER ASSEMBLY HOSE ASSEMBLY, 115" STREET ELBOW, 90, 3/4" CLAMP, HOSE, 1" - 2-1/4" HOSE BARB, 2" PIPE PLUG, 3/4" NPT MALE FT SUCTION HOSE, 2" HOSE ASSEMBLY, 120" BARB, 24C4-24MP FT SUCTION HOSE, 1-1/2" STREET ELBOW, 90, 1" PIPE BUSHING, 2" NPT-1-1/2" NPT SIGHT GAGE, TYPE S ELBOW, 12MJ-12MB ELBOW, 8MJ-12MB HOSE ASSEMBLY, 91" CONTROL VALVE, VDP12DDDDDD H.P.C.O. ADAPTER ELBOW, 16MB-12FR HYDRAULIC PUMP, OPPOSITE ENGINE HOSE ASSEMBLY, 107" SPIN-ON FILTER ASSEMBLY ELBOW, 8MJ-12FL "O" RING FLANGE KIT, 12FH BALL VALVE, BRONZE HOSE ASSEMBLY, 106" STREET ELL, 2" 45 DEG REDUCER BUSHING, 20MP-16FP "O"-RING CONNECTOR, 16MJ-12MB BENT TUBE, SWIVEL 16C2-16FJX GAUGE, FLUSH MOUNT, 6000 PSI CENTER BONDED MOUNT (Not Shown) SPECIAL WASHER (Not Shown) FLANGE FITTING, 24FL-24HOSE HOSE ASSEMBLY, 106" CONTROL VALVE, VDP12CDD CONTROL VALVE, VDP12CDCD PIPE NIPPLE, 2" X 4" CONNECTOR, 6MJ-4FP TEE, 12MJ-12FJX-12MJ ADAPTER, 12FJ-6MJ HOSE ASSEMBLY, 120" ELBOW, FLANGE 24-32FL90 W/ FLANGE KIT ELBOW, 12MJ-20FL90 W/ FLANGE KIT CONTROL VALVE CLAMP, 2-1/2" INSULATED (Not Shown) FILLER CAP SCREW, #10-32 X 1" RD HD MACH SCREW, 3/8"-16 X 1-1/4" HEX HD CAP (N.S.) SCREW, 3/8"-16 X 4-1/2" HEX HD CAP (N.S.) SCREW, 3/8"-16 X 4" HEX HD CAP (N.S.) SCREW, 3/8"-16 X 2-1/2" HEX HD CAP (N.S.) SCREW, 1/2"-13 X 1-1/4" HEX HD CAP NUT, #10-32 NYLOK HEX NUT, 3/8"-16 NYLOK HEX LOCKWASHER, 3/8" HELICAL LOCKWASHER, 1/2" HELICAL SPACER, CONTROL VALVE COVER PLATE GASKET, CLEANOUT & FILLER COVER SDU VALVE BRACKET WELDMENT RESERVOIR WELDMENT VI-39

42 LEFT CONTROL ASSEMBLY (HUSCO) VI-40

43 LEFT CONTROL ASSEMBLY (HUSCO) FUNCTION AIR ASSEMBLY AIR CYLINDER, 1.5 BORE X 1.71 STROKE SCREW, 1/4"-20 X 1-1/4" HEX HD CAP NUT, 1/4"-20 NYLOK HEX ZP NUT, 7/16"-20 HEX JAM PL CLEVIS PIN, 5/16" X 5/8" CLEVIS WELDMENT LEFT CONTROL ASSEMBLY (10 HANDLE) CONTROL CABLE, 96" CONTROL CABLE, 84" GAUGE, FLUSH MOUNT 6000 PSI CONTROL CABLE, 104" GREASE FITTING, 1/4" SCREW, 1/4"-20 X 3/4" HEX HD CAP GR5 ZP NUT, 1/4"-20 NYLOK HEX ZP NUT, 5/16"-24 HEX ZP NUT, 3/8"-16 HEX JAM ZP CLEVIS PIN, 5/16" X 1" ZP COTTER PIN, 1/16" X 3/4" SHAFT CLAMP, CONTROL BOX SPACER TUBE, 1-1/4" OD CONTROL HANDLE PIN (10,11,12) PLATE, SUPPORT SHAFT CLEVIS WELDMENT CONTROL FRAME WELDMENT (10,11,12 HND) CONTROL HANDLE ASSEMBLY, SHORT CONTROL HANDLE WELDMENT BEARING BR. FLG.752 X.879x KNOB, DECAL & PANEL KIT (10 HANDLE) KNOB, RED (IN-OUT) KNOB, BOOM (UP-DOWN) KNOB, BOOM (IN-OUT) KNOB, TILT (UP-DOWN) KNOB, SWING (CW-CCW) KNOB, UNDERLIFT (IN-OUT) KNOB, UNDERLIFT (UP-DOWN) KNOB, FOLD (UP-DOWN) PLUG, 2-1/2" PLUG, 7/8" SCREW, #6-32 X 1/2" RD HD PH SS KNOB, DECAL & PANEL KIT (cont'd) SCREW, 1/4"-20 X 3/4" MACH SCREW SCREW, 1/4"-20 X 3/4" THRD CUT HEX SCREW, 5/16"-18 X 1" RD MACH HD SS SCREW, 5/16"-18 X 2-1/2" HEX HD CAP GR5 ZP NUT, 1/4"-20 NYLOK HEX ZP NUT, 1/4" "J" TYPE TINNERMAN NUT, 5/16"-18 "J" TINNERMAN NUT, 3/8"-16 HEX JAM ZP NUT, HEX 6-32 SS DECAL PLATE, THROTTLE PLATE, BOOM CENTER CONTROL PANEL DECAL, SWING CONTROL PANEL DECAL, WRECKER CONTROL PANEL DECAL, SDU/ CONTROL PANEL DECAL, DRAG DECAL, LT FRONT OUTRIGGER (UP-DOWN) DECAL, RT FRONT OUTRIGGER (UP-DOWN) DECAL, LT REAR OUTRIGGER (UP-DOWN) DECAL, RT REAR OUTRIGGER (UP-DOWN) DECAL, FRONT OUTRIGGER (IN-OUT) DECAL, REAR OUTRIGGER (IN-OUT) DECAL, POWER DECAL, WINCH SPEED DECAL, WINCH AIR FREE SPOOL DECAL, FRONT WINCH FREE SPOOL DECAL, REAR WINCH FREE SPOOL DECAL, CONTROL CABLE SPEED PANEL, WINCH FREE SPOOL PANEL, GAUGE (10,11,12 HANDLE) PLATE, CONTROL (11 HANDLE) CONTROL PANEL WELDMENT SWITCH, McGILL PROPORTIONAL CONTROL KIT W/ DW ROTARY SELECT SWITCH OPERATOR PUSH BUTTON OPERATOR W/MTG (BLUE) PROPORTIONAL CONTROL VALVE KIT CLEVIS PIN, 3/16" X 3/4" ZP VALVE LINK WELDMENT (HUSCO) VI-41

44 LEFT CONTROL ASSEMBLY (PARKER) VI-42

45 LEFT CONTROL ASSEMBLY (PARKER) CONTROL KNOB, IN-OUT CONTROL KNOB, BOOM UP-DOWN CONTROL KNOB, JACK UP-DOWN CONTROL KNOB, BOOM IN-OUT CONTROL CABLE, 96" CONTROL CABLE, 84" CONTROL CABLE, 79" CONTROL CABLE, 104" GREASE FITTING, 1/4"-28 X ADJUSTABLE CLEVIS CONTROL KNOB, SWING CW-CCW CONTROL KNOB, UNDERLIFT IN-OUT CONTROL KNOB, UNDERLIFT UP-DOWN CONTROL KNOB, FOLD UP-DOWN SCREW, 1/4"-20 X 3/4" HEX HD CAP SCREW, 5/16"-18 X 2-1/2" HEX HD CAP NUT, 1/4"-20 HEX NYLOK NUT, 5/16"-18 "J" TINNERMAN NUT, 5/16"-18 HEX NYLOK NUT, 5/16"-24 HEX NYLOK NUT, 3/8"-16 HEX JAM WASHER, 1/4" FLAT WASHER, 3/4" FLAT (SPECIAL) CLEVIS PIN, 5/16" X 1" COTTER PIN, 1/16" X 3/4" CLAMP, SHAFT CONTROL BOX PLATE, SHAFT SUPPORT TUBE, SPACER PIN, CONTROL BOX CONTROL HANDLE WELDMENT CONTROL FRAME WELDMENT LEFT & RIGHT CONTROL LINK KIT SCREW, 5/16"-24 X 1-1/4" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" HEX HD CAP NUT, 5/16"-24 HEX NUT, 5/16"-24 HEX NYLOK NUT, 3/8"-16 HEX NYLOK LOCKWASHER, 5/16" INT. TOOTH PLATE, CONTROL (NOT SHOWN) PLATE, CONTROL (NOT SHOWN) CONTROL CABLE CONNECTOR SDU REMOTE CONTROL ASSEMBLY WIRE CONNECTOR, SPADE ELBOW, 4TB-4MP FT AIR HOSE, 1/4" O.D CONNECTOR, 4TB-4MP BRASS PLUG, 4MP CABLE SEALING GRIP HEX PIPE BUSHING CONVOLUTED LOOM, 3/8" X 8" CABLE TIE, 4" 18 LB BREATHER VENT, 2MP ELBOW, 4TB-2MP AIR SOLENOID VALVE (6) CIRCUIT BREAKER, HI-AMP WATERPROOF TERMINAL BLOCK 55 8 FT ELECTRICAL CABLE, 16/10 SO AIR FILTER/REGULATOR AIR LUBRICATOR MOUNTING BRACKET BREATHER VENT POWER PAL, 8 POSITION AIR CYLINDER SCREW, #8-32 X 3/4" RD HD SLOTTED SCREW, 1/4"-20 X 1-1/4" HEX HD CAP SCREW, 1/4"-20 X 2" HEX HD CAP HEX NUT & STAR WASHER, # NUT, 1/4"-20 HEX NYLOK NUT, 7/16"-20 HEX JAM WASHER, 1/4" FLAT CLEVIS PIN, 5/16" X 5/8" COTTERLESS SUPPORT, SOLENOID VALVE CLEVIS WELDMENT 72 1 HA0132 GAUGE, PSI VI-43

46 FRONT OUTRIGGER ASSEMBLY VI-44

47 FRONT OUTRIGGER ASSEMBLY SNAP RING, 1" GREASE FITTING SNAP RING, 2" EXTERNAL SLIDE PAD, BOOM BOTTOM EXTEND CYLINDER SPADE CYLINDER SCREW, 3/8"-16 X 1-1/2" HEX SKT SET SCREW, 5/8"-11 X 1" HEX HD CAP NUT, 3/8"-16 NYLOK HEX LOCKWASHER, 5/8" HELICAL SHAFT, EXTEND CYLINDER OUTER BOOM SHAFT, JACK CYLINDER, LOWER SHAFT, OUTRIGGER ARM TO PAD SHAFT, JACK CYLINDER, UPPER SHAFT, EXTEND CYLINDER BASE FRONT OUTRIGGER PAD WELDMENT FRONT OUTRIGGER BEAM WELDMENT FRONT OUTRIGGER VERT TUBE WELDMENT VI-45

48 FRONT OUTRIGGER HYDRAULICS (HUSCO) VI-46

49 FRONT OUTRIGGER HYDRAULICS (HUSCO) CONNECTOR, 6MJ-8MB HOSE CLAMP, INSULATED 1" (Not Shown) ELBOW, 6MJ-4MP CONNECTOR, 6MJ-4MP HOSE CLAMP, 1/2" CABLE TIE (Not Shown) ADAPTER, 6MJ-6MBL HOSE ASSEMBLY, 131" CONNECTOR, 8MB-6FB HOSE ASSEMBLY, 73" HOSE ASSEMBLY, 66" HOSE ASSEMBLY, 82" HOSE ASSEMBLY, 141" HOSE ASSEMBLY, 75" HOSE ASSEMBLY, 96" FT BLACK SKUFF JACKET (Not Shown) EXTEND CYLINDER VERTICAL CYLINDER OUTRIGGER CONTROL VALVE HYDRAULIC TUBING SADDLE CLAMP, 2-1/2" PIPE FITTING, 6FB-8MP ORIFICE CONNECTOR, 6MJ-6MBR-3/64 VI-47

50 FRONT OUTRIGGER HYDRAULICS (PARKER) VI-48

51 FRONT OUTRIGGER HYDRAULICS (PARKER) HOSE CLAMP, INSULATED 1" (Not Shown) ELBOW, 6MJ-4MP CONNECTOR, 6MJ-4MP HOSE CLAMP, 1/2" CONTROL VALVE, VDP12DDDDDD CONNECTOR, 6MJ-10MB CABLE TIE (Not Shown) ADAPTER, 6MJ-6MBL HOSE ASSEMBLY, 131" HOSE ASSEMBLY, 73" HOSE ASSEMBLY, 66" HOSE ASSEMBLY, 82" HOSE ASSEMBLY, 141" HOSE ASSEMBLY, 75" HOSE ASSEMBLY, 96" FT BLACK SKUFF JACKET EXTEND CYLINDER SPADE CYLINDER HYDRAULIC TUBING SADDLE CLAMP, 2-1/2" PIPE FITTING, 6FB-8MP VI-49

52 REAR OUTRIGGER ASSEMBLY VI-50

53 REAR OUTRIGGER ASSEMBLY SNAP RING, 1" CYLINDER, SPADE HYD TWIN CYLINDER ASSY, REAR OUTR SCREW, 1/4"-20 X 3/4" HEX HD CAP SCREW, 3/8"-16 X 1" HEX HD CAP SCREW, 3/8"-16 X 1-1/2" HEX SKT SET NUT, 3/8"-16 NYLOK HEX LOCKWASHER, 1/4" HELICAL LOCKWASHER, 3/8" HELICAL SHAFT, JACK CYLINDER, UPPER SHAFT, JACK CYLINDER, LOWER SHAFT, UPPER SPADE SHAFT, UPPER SPADE COVER, OUTER HORIZ OUTRIGGER SPACER, TOP SPACER, BOTTOM SHIM, BOTTOM OUTER OUTRIGGER WELDMENT, LH REAR OUTER OUTRIGGER WELDMENT, RH REAR ND STAGE BOOM WELDMENT RD STAGE OUTRIGGER BOOM WELDMENT OUTRIGGER PAD, INTERMEDIATE REAR OUTRIGGER PAD PIN, REAR OUTRIGGER PAD ASSY DRIVE SCREW, #10 X 1/2" RD HD CHAIN, SASH 20" LONG PIN WELDMENT, REAR OUTRIGGER PAD -- 1 HD1259 PIN, SNAPPER KIT, SPADE & BLADE, ROT. REAR. OUTRIGGER SCREW, 1/2"-13 X 1-1/2" HEX HD CAP NUT, 1/2"-13 NYLOK HEX BLADE, REAR OUTRIGGER SPADE SPADE WELDMENT, REAR OUTRIG SHORT PIN ASSY, JACK PAD VI-51

54 REAR OUTRIGGER HYDRAULICS (HUSCO) VI-52

55 REAR OUTRIGGER HYDRAULICS (HUSCO) CONNECTOR, 6MJ-8MB ELBOW, 8FP-8FP NIPPLE, BLACK PIPE 1/2" HOSE ASSEMBLY, 183" HOSE ASSEMBLY, 240" ELBOW, 6MJ-6MB CONNECTOR, 6J-8MP CLAMPING UNIT SOCKET HD STACKING NUT SPLIT BUSHING, 1" FT BLACK SCUFF JACKET, SJ SPADE CYLINDER OUTRIGGER CONTROL VALVE TWIN CYLINDER ASSY, REAR OUTRIGGER SCREW, 5/16"-18 X 3/4" HEX HD CAP GR5 VI-53