440 SERIES / DFT 400

Transcription

1 OWNER'S MANUAL 440 SERIES / DFT 400 INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice. All ratings specified are based on structural factors only, not vehicle capacities or capabilities. Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee FORM NO / 94 Phone (423) FAX (423) PRICE $25.00

2 LIMITED WARRANTY MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in material and workmanship for a period of twelve (12) months from date placed in service, but in no event shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve (12) months from date placed in service, whichever is earlier. MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or alterations have been made unless authorized by MILLER. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages concerning or relating to any product or parts, whether based on negligence, strict liability, breach of contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss resulted from any general or particular requirement which MILLER knew or had reason to know about at the time of sale. MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted under applicable law, pass on to the purchaser such manufacturer's or seller's warranty. MILLER, whose policy is one of continuous improvement, reserves the right to improve its products through changes in design or materials as it may deem desirable without being obligated to incorporate such changes in products previously sold. This warranty is not intended to cover or include the following items, which are set forth by way of example and not limitation: A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to weather, road conditions, road treatments, etc. B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure to provide reasonable and necessary maintenance, or uses for which the equipment was not designed or intended. C. Alterations or modifications that affect performance, operation or reliability. D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts. IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY OTHER IMPROPER USE. Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee SERIAL NUMBER Telephone (423)

3 Section VI - PARTS This Section is provided by the manufacturer for the purpose of ordering any component part of the HOLMES 440 Wrecker that may be required when part replacement is necessary. Be certain to use only original equipment replacement parts for warranty purposes as well as for keeping your HOLMES 440 Wrecker in its original state and optimum operating capacities. When ordering replacement or spare parts be sure to provide the following information to the manufacturer's Parts Department. 1. Manual Number & Date of Publication 2. Manual Page Number 3. Page Title 4. Reference Number of Part Desired 5. Part Number 6. Part Description 7. Quantity of Part Desired Providing this information will help ensure that the correct parts will be delivered to you in an expedient manner without delay. Should additional information be required for repair or replacement of certain components, contact your Wrecker Manufacturer Authorized Representative. The Manufacturer reserves the right, without notice or obligation, to improve or modify their products, which may change the specifications, models and feature availability. VI-1

4 440B BODY ASSEMBLY (Continued on Page VI-4) VI-2

5 440B BODY ASSEMBLY (Continued on Page VI-5) 1 8 FT SPONGE, 3/4" X 1/8" W/ ADHBK GREASE FITTING, ALEMITE /16" X 10' CHAIN ASSEMBLY MUDFLAP, BLACK W/ RWL (GO138B) LATCH, TOOL COMPARTMENT DOOR BACK UP ALARM LIGHT, SEALED RED, STOP & TURN LIGHT, SEALED WHITE, BACKUP LIGHT, SEALED MARKER, RED LIGHT, SEALED MARKER, AMBER GROMMET, MARKER LIGHT GROMMET, TAILLIGHT HINGE, DOOR SCREW, #8-32 X 1/2" RD HD PHILLIPS SCREW, #10-32 X 1" RD HD MCH SCREW, 1/4-20 X 1-1/4" HEX HD CAP SCREW, 1/4"-20 X 3/4" TYPE "F" THD CUT SCREW, 1/4-20 X 3/4" HEX HD CAP SCREW, 1/4-20 X 1" HEX HD CAP SCREW, 5/16"-18 X 1" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SCREW, 1/2"-13 X 1-1/5" HEX HD CAP NUT & STAR WASHER, #8-32 HEX NUT, #10-32 NYLOK HEX NUT, 1/4"-20 NYLOK HEX VI-3

6 440B BODY ASSEMBLY (Continued from Page VI-2) VI-4

7 440B BODY ASSEMBLY (Continued from Page VI-3) CLIP, 1/4" "U" TYPE TINNERMAN NUT, 3/8"-16 NYLOK HEX NUT, 1/2"-13 NYLOK HEX WASHER, 1/4" FLAT LOCKWASHER, 1/4" HELICAL LOCKWASHER, 5/16" HELICAL WASHER, 3/8" FLAT WASHER, 1/2" FLAT GUARD, CONTROL STATION BAR, MUDFLAP MUDFLAP MOUNTING ANGLE, RIGHT MUDFLAP MOUNTING ANGLE, LEFT ACCESS COVER, FILTER BRACKET, MARKER LIGHT STORAGE TUBE WELDMENT LT CHAIN BOX WELDMENT RT CHAIN BOX WELDMENT BODY WELDMENT B 60 C.A BA0259 PIN, "D" RING 45 2 BA0283 "D" RING 46 2 GR400 RUBBER CATCH, HOOD, HD 8" 47 1 HB73 ANGLE, DOOR SPLASH GUARD 48 2 HD0106 SPRING PIN, 1/4" X 1-3/4" 49 1 HF56 SMALL DOOR WELDMENT VI-5

8 DFT 400 WHEEL LIFT ASSEMBLY VI-6

9 DFT 400 WHEEL LIFT ASSEMBLY GREASE FITTING, ALEMITE SPRING, DETENT GREASE FITTING, ALEMITE BALL, DETENT CLAMP SLIDE PAD, NYLATRON BUSHING BUSHING SLIDE PAD, NYLATRON SCREW, 3/8"-16 X 1-1/2" HEX SKT SET SCREW, 3/8"-16 X 7/8" HEX HD CAP SETSCREW, 3/8"-16 X 1/2" ALLEN HD NUT, 1/4"-20 HEX NUT, 3/8"-16 NYLOK HEX NUT, 3/8"-16 HEX JAM 16 * WHEEL LIFT MOUNTING SPACER SCREW, 1/2"-13 X 1" HEX HD CAP SHAFT, CYLINDER SPACER SHAFT, EXTEND CYLINDER HOSE GUARD THRUST WASHER UPPER SHAFT WELDMENT, BOOM SHAFT WELDMENT, ARM SHAFT, LIFT CYLINDER PIN, CROSSTUBE PIVOT CROSSTUBE, INNER WELDMENT UPPER ARM WELDMENT LOWER SHAFT WELDMENT, BOOM OUTER BOOM WELDMENT INNER BOOM WELDMENT FRAME WELDMENT UPPER ARM ASSY - INCLUDES ITEMS 8 & WHEEL LIFT MOUNTING HARDWARE SCREW, 5/8"-11 X 2" HEX HD CAP SCREW, 5/8"-11 X 2-1/4" HEX HD CAP NUT, 5/8"-11 NYLOK HEX WASHER, 5/8" FLAT VI-7

10 DFT 400 WHEEL LIFT HYDRAULICS VI-8

11 DFT 400 WHEEL LIFT HYDRAULICS SPOOL VALVE CONNECTOR, 6MJ-8MB ELBOW, 8MJ-10MB HOSEBARB, 12C4-12MP 5 4 FT HOSE, 3/4" RETURN CLAMP, HOSE 1" GREASE FITTING, ALEMITE CLAMP, HOLDING VALVE ELBOW, 6MJ-4MP BRANCHTEE, 6MJ-6MJ-4MP ELBOW, 6MJ-6MP HOSE ASSEMBLY, 120" ELBOW, 12MB-12FP TEE, 6MJ-6MJ-6MJ GREASE FITTING, ALEMITE HOSE, LIFT CYLINDER, 45" CONNECTOR, 6MJ-6MP HOSE ASSEMBLY, 18" HOSE ASSEMBLY, 81" CONNECTOR, 6MJ-6MB ELBOW, 6MJ-6FJX HOLDING VALVE, 4000 PSI CYLINDER, EXTEND VALVE, RESTRICTOR TEE, 6MJ-6MJ-6MP HOSE ASSEMBLY, 18" HOSE ASSEMBLY, 35" CYLINDER, LIFT CYLINDER, TILT, L.H CYLINDER, TILT, R.H FT SKUFF JACKET SCREW, 1/4"-20 X 2" RD HD SLOTTED SCREW, 3/8"-16 X 4" HEX HD CAP NUT, 3/8"-16 NYLOK HEX NUT, 1/4"-20 HEX WASHER, 1/4" FLAT LOCKWASHER, 1/4" HELICAL BRACKET, CHECK VALVE MOUNTING VI-9

12 WRECKER ASSEMBLY B VI-10

13 WRECKER ASSEMBLY B SNAP RING, 1" GREASE FITTING, ALEMITE WINCH, HLC-246, LEFT REAR BEARING PAD, NYLATRON CYLINDER, BOOM EXTENSION SCREW, 1/4"-20 X 1/2" HEX HD CAP SCREW, 5/16"-18 X 1" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SCREW, 3/8"-16 X 3-1/2" HEX HD CAP SCREW, 3/8"-16 X 7/8" HEX HD CAP SCREW, 5/8"-11 X 1-3/4" HEX HD CAP NUT, 3/8"-16 NYLOK HEX NUT, 5/8"-11 NYLOK HEX LOCKWASHER, 1/4" HELICAL LOCKWASHER, 5/16" HELICAL LOCKWASHER, 3/8" HELICAL WASHER, 5/8" FLAT PIN, EXTEND CYLINDER PIVOT SHAFT, EXTEND CYLINDER, OUTER BOOM PAD RETAINER, BOLT-ON COVER, BOOM PIN, BOOM PIVOT INNER BOOM, SINGLE OUTER BOOM WELDMENT B WINCH BUCKET B BOOM END SWIVEL ASSEMBLY 27 4 BK518 PIN, BOOM CYLINDER 28 4 BK519 HAIR PIN, BOOM CYLINDER PIN 29 2 IT27B CYLINDER, BOOM ELEVATION VI-11

14 WRECKER HYDRAULICS B VI-12

15 WRECKER HYDRAULICS B 1 REF VALVE, 3-SPOOL, CONTROL VALVE, 3-SPOOL, CONTROL CONNECTOR, 8MJ-8MP CONNECTOR, 8MJ-8MB CONNECTOR, 6MJ-8MB ELBOW, 8MJ-10MB HOSEBARB, 12C4-12MP CLAMP, HOSE 1" MOTOR, CHAR-LYNN HYDRAULIC FILTER ASSEMBLY, RETURN LINE ELBOW, 6MJ-4MP ELBOW, STREET 4MP-4FP BRANCHTEE, 6MJ-6MJ-4MP FITTING, H.P.C.O HOSE ASSEMBLY, 120" LONG ELBOW, 12MB-12FP ELBOW, 8MJ-8MB MALE CONNECTOR, 6MJ-4MP ELBOW, 6MJ-8MB HOSE ASSEMBLY, H.P.C.O ELBOW, 8MJ-12MB ELBOW, 6MJ-6MB FT HOSE, 3/4" RETURN ELBOW, 6MJ-6FJX HOLDING VALVE, 4000 PSI 26 REF CYLINDER, EXTEND CONNECTOR, 8MJ-12MB HOSE ASSEMBLY, 15" LONG HOSE ASSEMBLY, 65" LONG HOSE ASSEMBLY, 131" LONG TEE, 6MJ-6MJ-6FJX HOSE ASSEMBLY, 20" LONG HOSE ASSEMBLY, 80" LONG SCREW, 1/2"-13 X 1-1/4" HEX HD CAP LOCKWASHER, 1/2" HELICAL 36 4 GR247 HOSE ASSEMBLY, 30" LONG 37 REF. IT27B CYLINDER, BOOM ELEVATION VI-13

16 WRECKER ASSEMBLY B VI-14

17 WRECKER ASSEMBLY B SNAP RING, 1" GREASE FITTING, ALEMITE WINCH, HLC-246, RIGHT REAR WINCH, HLC-246, LEFT REAR BEARING PAD, NYLATRON CYLINDER, BOOM EXTENSION SCREW, 1/4"-20 X 1/2" HEX HD CAP SCREW, 5/16"-18 X 1" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SCREW, 3/8"-16 X 3-1/2" HEX HD CAP SCREW, 3/8"-16 X 7/8" HEX HD CAP SCREW, 5/8"-11 X 1-3/4" HEX HD CAP NUT, 3/8"-16 NYLOK HEX NUT, 5/8"-11 NYLOK HEX LOCKWASHER, 1/4" HELICAL LOCKWASHER, 5/16" HELICAL LOCKWASHER, 3/8" HELICAL WASHER, 5/8" FLAT PIN, EXTEND CYLINDER PIVOT SHAFT, EXTEND CYLINDER, OUTER BOOM PAD RETAINER, BOLT-ON COVER, BOOM PIN, BOOM PIVOT INNER BOOM, DUAL OUTER BOOM WELDMENT B WINCH BUCKET B BOOM END SWIVEL ASSEMBLY 27 4 BK518 PIN, BOOM CYLINDER 28 4 BK519 HAIR PIN, BOOM CYLINDER PIN 29 2 IT27B CYLINDER, BOOM ELEVATION VI-15

18 WRECKER HYDRAULICS B VI-16

19 WRECKER HYDRAULICS B 1 REF VALVE, 3-SPOOL, CONTROL VALVE, 4-SPOOL, CONTROL CONNECTOR, 8MJ-8MP CONNECTOR, 8MJ-8MB CONNECTOR, 6MJ-8MB ELBOW, 8MJ-10MB HOSEBARB, 12C4-12MP CLAMP, HOSE 1" MOTOR, CHAR-LYNN HYDRAULIC FILTER ASSEMBLY, RETURN LINE ELBOW, 6MJ-4MP ELBOW, STREET 4MP-4FP BRANCHTEE, 6MJ-6MJ-4MP FITTING, H.P.C.O HOSE ASSEMBLY, 120" LONG ELBOW, 12MB-12FP ELBOW, 8MJ-8MB MALE CONNECTOR, 6MJ-4MP ELBOW, 6MJ-8MB HOSE ASSEMBLY, H.P.C.O ELBOW, 8MJ-12MB ELBOW, 6MJ-6MB FT HOSE, 3/4" RETURN ELBOW, 6MJ-6FJX HOLDING VALVE, 4000 PSI 26 REF CYLINDER, EXTEND CONNECTOR, 8MJ-12MB HOSE ASSEMBLY, 15" LONG HOSE ASSEMBLY, 65" LONG HOSE ASSEMBLY, 131" LONG TEE, 6MJ-6MJ-6FJX HOSE ASSEMBLY, 20" LONG HOSE ASSEMBLY, 80" LONG SCREW, 1/2"-13 X 1-1/4" HEX HD CAP LOCKWASHER, 1/2" HELICAL 36 4 GR247 HOSE ASSEMBLY, 30" LONG 37 REF. IT27B CYLINDER, BOOM ELEVATION VI-17

20 OUTER CROSSTUBE & TIRE RESTRAINT ASSEMBLY VI-18

21 OUTER CROSSTUBE & TIRE RESTRAINT ASSEMBLY CROSSTUBE, LEFT OUTER, W/ BASKET STRAP HOOKS (COMPLETE) CROSSTUBE, RIGHT OUTER, W/ BASKET STRAP HOOKS (COMPLETE) GREASE FITTING, ALEMITE KNOB SPRING, PLUNGER PIN STRAP, 9" RUBBER NUT, 1/4"-20 NYLOK HEX NUT, 3/8"-16 JAM HEX WASHER, 1/4" FLAT PIN, 3/16" X 1" ROLL PIN, 5/32" X 1" ROLL PIN, PLUNGER HANDLE, TEE HANDLE, LEFT PLUNGER HANDLE, RIGHT PLUNGER TIRE RESTRAINT, LEFT, W/ BASKET STRAP SLOT TIRE RESTRAINT, RIGHT, W/ BASKET STRAP SLOT CROSSTUBE, LEFT OUTER CROSSTUBE, RIGHT OUTER " NYLON POLY COAT STRAP VI-19

22 HYDRAULIC WINCH VI-20

23 HYDRAULIC WINCH BEARING CAP BEARING CAP JAW CLUTCH COVER DRUM "Y" GEAR L.H. 46: HOUSING, CLUTCH HOUSING, GEAR KEY KEY KEY LEVER, SHIFTER SHAFT, SHIFTER SHAFT, DRUM "Y" WORM L.H. 46: YOKE BALL, POPPET BEARING, BALL BUSHING BUSHING SCREW, 1/4-20 X 3/4" HEX HD CAP SCREW, 1/4-20 X 7/8" HEX HD CAP SCREW, 3/8-16 X 3/4" HEX HD CAP SCREW, 1/4-20 X 1-1/4" SKT HD LESS SET SCREW, 3/8-16 X 3/8" SOC HD LESS SET SCREW, 1/4-20 X 1/2" SQ HD SET SCREW, 5/16-18 X 1/2" SQ HD SET LOCKWASHER, 3/8 MED SECT DRAG BRAKE GASKET GASKET KEY, BARTH KEY, BARTH FITTING, LUBE FITTING, RELIEF REDUCER PIPE PLUG PLASTIC PLUG OIL SEAL OIL SEAL SPRING, POPPET SPRING THRUST WASHER THRUST WASHER VI-21

24 CONTROL & CROSSROLD ASSEMBLY VI-22

25 CONTROL & CROSSROLD ASSEMBLY GROMMET, SPLIT PLASTIC KNOB, CABLE "IN-OUT" (RED) KNOB, WRECKER BOOM "UP-DN" (BLACK) KNOB, WRECKER BOOM "IN-OUT" (BLACK) KNOB W/L "TILT" (GRAY) KNOB, W/L "IN-OUT" (GRAY) KNOB, W/L "UP-DN" (GRAY) SCREW, 1/4"-20 X 3/4" HEX HD CAP CLIP, 1/4" TINNERMAN NUT, 3/8"-16 HEX JAM ESLOK NUT, 3/8"-16 HEX JAM LOCKWASHER, 1/4" HELICAL CLEVIS PIN, 5/16" X 5/8" COTTERLESS COTTER PIN, 3/16" X 1-1/4" COTTER PIN, 1/8" X 3/4" EXTENSION, CONTROL ROD LONG EXTENSION, CONTROL ROD SHORT ANGLE, CROSSROD BEARING CROSSROD - W/L CROSSROD - WRECKER CROSSROD - TILT CHANNEL, CROSS ROD BEARING LEVER, CONTROL ARM, CROSS CONTROL CONTROL ROD, SHORT CONTROL ROD, MEDIUM CONTROL ROD, LONG VI-23

26 WINCH CLUTCH CONTROL SPRING, COMPRESSION "T" HANDLE ADJUSTING YOKE SCREW, 5/16"-18 X 1/2" SQ HD SET SCREW, 3/8"-16 X 1" HEX HD CAP SCREW, 3/8"-16 X 2-1/2" HEX HD CAP NUT, 3/8"-16 JAM WASHER, 3/8" LOCK WASHER, 1/2" FLAT PIN, 1/2" X 1-1/2" CLEVIS PIN, 1/8" X 1-1/4" COTTER PIN, 5/32" X 1" ROLL MOUNTING CHANNEL WELDMENT, BELL CRANK CONTROL ROD, SINGLE WINCH CONTROL ROD, DUAL WINCH VI-24

27 BOOM END SEWIVEL " SHEAVES NAP RING, 2-1/2" DIA EXT GREASE FITTING "U" BOLT, 3/8" SCREW, 1/4"-20 X 1/2" HEX HD CAP NUT, 3/8"-16 HEX NYLOK NUT, 3/8"-16 HEX JAM LOCKWASHER, 1/4" HELICAL RETAINER, SHEAVE SHAFT SHAFT, SHEAVE WASHER-SPACER CABLE GUIDE BOOM END SWIVEL VI-25

28 HYDRAULIC CYLINDERS - WHEEL LIFT HYDRAULIC CYLINDER, LIFT (COMPLETE) SEAL KIT, LIFT CYLINDER HYDRAULIC CYL., TILT (COMPLETE) L.H HYDRAULIC CYL., TILT (COMPLETE) R.H SEAL KIT, TILT CYLINDER HYDRAULIC CYL., EXTEND (COMPLETE) SEAL KIT, EXTEND CYLINDER VI-26

29 HYDRAULIC CYLINDERS - WHEEL LIFT 1 1 IT27B HYDRAULIC CYLINDER, LIFT (COMPLETE) 2 1 IT97 SEAL KIT, LIFT CYLINDER HYDRAULIC CYL., EXTEND (COMPLETE) SEAL KIT, EXTEND CYLINDER VI-27

30 LIGHT KIT HOUSING BULB PIVOT SCREW LOCKWASHER NUT MOUNTING BRACKET MOUNTING SCREW LIGHT, BACKUP (COMPLETE) LIGHT, SEALED RED, STOP & TURN LIGHT, SEALED WHITE, BACKUP TAIL LIGHT GROMMET & PLUG KIT VI-28

31 LIGHT KIT (cont'd) LIGHT, SEALED MARKER, RED LIGHT, SEALED MARKER, AMBER GROMMET MOUNTING KIT W/PLUG VI-29

32 LIGHTING ASSESSORIES VI-30

33 LIGHTING ASSESSORIES LICENSE PLATE HOLDER RUBBER GROMMET LICENSE PLATE ILLUMINATOR WRECKER SPECIAL LIGHT SPOTLIGHT W/GASKET SCREW, #10-32 X 3/4" SELF-TAPPING SCREW, 1/4"-20 X 1-1/2" HEX HD CAP SCREW, 1/4"-20 X 3/4" PAN HD SCREW, 1/4"-20 X 3/4" THD CUT HEX HD SCREW, 3/8"-16 X 1-1/2" HEX HD CAP NUT, 1/4"-20 HEX PLAIN NUT, 1/4"-20 NYLOK HEX NUT, 3/8"-16 HEX HD NYLOK LOCKWASHER, 1/4" WASHER, 3/8" FLAT ANGLE, PYLON BASE REINFORCING GASKET, PYLON BASE - 33" PYLON GASKET, PYLON BASE - 36" PYLON GASKET, PYLON BASE - 40" PYLON GASKET, PYLON BASE - 42" PYLON GASKET, PYLON BASE - 45" PYLON "T" BOLT ADAPTER LIGHT MOUNTING PYLON - 33" LIGHT MOUNTING PYLON - 36" LIGHT MOUNTING PYLON - 40" LIGHT MOUNTING PYLON - 42" LIGHT MOUNTING PYLON - 45" BRACKET, LICENSE PLATE MOUNTING VI-31

34 FOLD DOWN LIGHT BAR BRACKET SCREW, 3/8"-16 X 1" HEX HD CAP NUT, 5/16"-18 HEX NUT, 3/8"-16 HEX NYLOK WASHER, 5/16" FLAT LOCKWASHER, 5/16" HELICAL COTTER PIN, 1/8" X 3/4" ROD, CONNECTING TEE BOLT - FOLD DOWN LIGHT BRACKET L.H. TOP HINGE ASSEMBLY R.H. BOTTOM HINGE ASSEMBLY L.H. BOTTOM HINGE ASSEMBLY R.H. TOP HINGE ASSEMBLY VI-32

35 OPTIONAL PTO PANEL SWITCH PANEL HOUSING SCREW, #10-32 X 3-3/8", MTG LOCKWASHER, #10 EXT TOOTHE WASHER, #10 FLAT NUT, # JAM NUT ACTUATOR DISK PTO CABLE, 14 FT (*SPECIFY MAKE & MODEL OF TRUCK) PTO KNOB FUSE, 30 AMP SWITCH, LARGE ROCKER SWITCH, SMALL ROCKER PTO LIGHT SWITCH RING CONNECTOR SPADE CONNECTOR VI-33

36 TOW SLING ADAPTERS SPRING, PLUNGER GREASE FITTING SCREW, 5/16"-18 X 1-1/4" SELF-TAPPING SCREW, 3/8"-16 X 1-1/4" RD HD CARRIAGE NUT, 3/8"-16 HEX NYLOK ROLL PIN PIN, PLUNGER TOW SLING BELT GRIP PLATE BELT RETAINER TEE HANDLE CHAIN KEEPER, LEFT CHAIN KEEPER, RIGHT INNER ADJUSTMENT TUBE, LEFT INNER ADJUSTMENT TUBE, RIGHT MOUNTING BRACKET "J" HOOK ASSEMBLY VI-34

37 WHEEL LIFT ATTACHMENTS BALL, TRAILER, 2" CHROME SCREW, 3/4"-10 X 5-1/2" HEX HD CAP LOCKWASHER, 3/4" HELICAL TOWBALL BRACKET SCREW, 1/2"-13 X 1-1/2" HEX HD CAP NUT 1/2"-13 NYLOK HAIR PIN COTTER OUTRIGGER BLADE SPADE ATTACHMENT SPADE PIN VI-35

38 PUMP & RESERVOIR HYDRAULICS HOSEBARB, 12C4-12MP BARB, 16C4-16MP 3 4 FT HOSE, 3/4" RETURN 4 9 FT HOSE, 1" SUCTION CLAMP, HOSE 1" RETURN LINE FILTER ASSEMBLY CLAMP, HOSE 1-1/2" INSULATED PIPE PLUG, 3/4" MALE HOSE ASSEMBLY, 120" HOSEBARB, 1" FJIX X 1" HYD CONN, 8MJ-16MB HYD CONN, 16MJ-16MB PIPE NIPPLE, 3/4" X 12" ELBOW, 45 STREET, 1" FILLER CAP ASSEMBLY SCREW, #10-32 X 1/2" THD CUT PHILLIPS HD SCREW, 3/8"-16 X 1-1/2" HEX HD CAP CLIP, 3/8", "J" TYPE TINNERMAN FLATWASHER, 3/8" LOCKWASHER, 3/8" EXT TOOTH RESERVOIR WELDMENT 22 1 HC1338 GATE VALVE, 1" BRASS 23 1 IT74 PIPE NIPPLE, 1" X 6" VI-36

39 WIRING KIT FRONT HARNESS & JUNCTION BOX REAR HARNESS - FI/4400/ WORK LIGHT HARNESS BACK UP ALARM HARNESS POLE SOCKET & HARNESS VI-37

40 THROTTLE CONTROL THROTTLE CONTROL, 16' - 60 C.A THROTTLE CONTROL, 18' - 84 C.A KIT, THROTTLE, FORD & CHEVY VI-38

41 NOTES

42 Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee (423)