15 SERIES 2 & 3 CAR CARRIERS

Transcription

1 OWNER S MANUAL 15 SERIES 2 & 3 CAR CARRIERS INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice All ratings specified are based on structural factors only, not vehicle capacities or capabilities. Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee FORM NO Rev. 6/05 Phone (423) FAX (423) PRICE $25.00

2 LIMITED WARRANTY MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original purchaser that each new MILLER Carrier will be free from defects in material and workmanship for a period of one (1) year from the date of purchase. The purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event shall such notification be received by MILLER later than twelve (12) months from date of delivery. The obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at our factory, or at a point designated by us, of such part or parts as shall appear to us upon inspection to be defective in material or workmanship. New or remanufactured parts will be used for any replacement. This warranty does not obligate MILLER to bear the cost of labor or transportation charges in connection with the replacement or repair of any parts found to be defective, nor shall it apply to a product upon which repairs or alterations have been made unless authorized by us. MILLER shall in no event be liable for any incidental or consequential damages or contingent arising out of the failure of any parts or products to operate properly. NO IMPLIED, EXPRESS, OR STATUTORY WARRANTY OTHER THAN STATED HEREIN IS MADE OR AUTHORIZED TO BE MADE BY OR FOR US, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. MILLER makes no warranty, express or implied, as to finished products manufactured or supplied by another manufacturer or supplier by MILLER to purchaser, including, but not limited to, any vehicle to which a MILLER product may be affixed or accessories or wire rope (cable), and expressly disclaims any implied warranties of merchantability or fitness for a particular purpose as to such equipment or products. This language shall in no way affect or diminish the rights of purchaser to rely on such warranties as are extended by such manufacturers or suppliers. MILLER, whose policy is one of continuous improvement, reserves the right to improve its product through changes in design or materials as it may deem desirable without being obligated to incorporate such changes in products of prior manufacture. IT IS EXPRESSLY UNDERSTOOD THAT THERE IS NO IMPLIED WARRANTY THAT MILLER CARRIERS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PERSONS OR OTHER IMPROPER USE. THIS WARRANTY IS NOT TRANSFERABLE. SERIAL NUMBER

3 Section VI - PARTS This Section is provided by the manufacturer for the purpose of ordering any component part of the 15 Series Car Carrier that may be required when part replacement is necessary. Be certain to use only original equipment replacement parts for warranty purposes as well as for keeping your 15 Series Car Carrier in its original state and optimum operating capacities. When ordering replacement or spare parts be sure to provide the following information to your carrier manufacturer authorized representative. 1. Manual Number & Date of Publication 2. Manual Page Number 3. Page Title 4. Reference Number of Part Desired 5. Part Number 6. Part Description 7. Quantity of Part Desired Providing this information will help ensure that the correct parts will be delivered to you in an expedient manner without delay. Should additional information be required for repair or replacement of certain components, contact Miller Industries, Hermitage, PA, Phone: , FAX The Manufacturer reserves the right, without notice or obligation, to improve or modify their products, which may change the specifications, models and feature availability. VI-1

4 ALUMINUM BED ASSEMBLY FULL SIDE VI-2

5 ALUMINUM BED ASSEMBLY FULL SIDE REF. NO. PART NO. REQ D NUMBER DESCRIPTION 1 1 * CARRIER BED WELDMENT WINCH - 4 TON WORM SPACER, WINCH BRACKET WINCH FRAME - 4 TON WORM WINCH CABLE ASSEMBLY 6 1 * CAB PROTECTOR WELDMENT - SPECIFY CHASSIS COVER PLATE ANTI-TILT PLATE HOSE TRAY HOSE TRAY BEARING PAD KIT BEARING PAD KIT - 21 THRU HOSE CLAMP WELDMENT LIGHT 2.5" AMBER REFLEX LED (MCL59AB) LIGHT 2.5" RED REFLEX LED (MCL509RB) LIGHT 2.5" GROMMET A MARKER LIGHT, AMBER BED FILLER PLATE x 5/8" BHSCS SS ROLLER PIN WELDMENT ROLLER TRAY MAT FRONT SAFETY CHAIN ASSEMBLY - 5/16" x KEY HOLE PLATE /8-16 x 1-1/4" CARRIAGE HEAD BOLT SS /8-16 HEX NUT SS /8 LOCK WASHER SS * CONTACT DISTRIBUTOR FOR ADDITIONAL INFORMATION VI-3

6 ALUMINUM BED ASSEMBLY REMOVABLE RAIL VI-4

7 ALUMINUM BED ASSEMBLY REMOVABLE RAIL REF. NO. PART NO. REQ D NUMBER DESCRIPTION 1 1 * CARRIER BED WELDMENT WINCH - 4 TON WORM SPACER, WINCH BRACKET WINCH FRAME - 4 TON WORM WINCH CABLE ASSEMBLY 6 1 * CAB PROTECTOR WELDMENT - SPECIFY CHASSIS COVER PLATE ANTI-TILT PLATE HOSE TRAY HOSE TRAY REAR REMOVABLE RAIL - STEEL (19 THRU 21 6) MID REMOVABLE RAIL - STEEL (19 THRU 21 6) 12 2 * FRONT REMOVABLE RAIL - STEEL LYNCH PIN BEARING PAD KIT - 17 THRU BEARING PAD KIT - 21 THRU HOSE CLAMP WELDMENT LIGHT 2.5" AMBER REFLEX LED (MCL59AB) TRAY MATS LIGHT 2.5" GROMMET LED MARKER LIGHT, AMBER (RECT) LED MARKER LIGHT, RED (RECT) J-BAR J-BAR MOUNTING BRACKET (RR ONLY) FRONT SAFETY CHAIN ASSEMBLY - 5/16" X KEY HOLE PLATE /8-16 x 1-1/4" CARRIAGE HEAD BOLT SS /8-16 HEX NUT SS /8 LOCK WASHER SS * CONTACT DISTRIBUTOR FOR ADDITIONAL INFORMATION VI-5

8 STEEL BED ASSEMBLY TUBE SIDE VI-6

9 STEEL BED ASSEMBLY TUBE SIDE REF. NO. PART NO. REQ D NUMBER DESCRIPTION 1 1 * CARRIER BED WELDMENT TON WINCH ASSEMBLY SPACER, WINCH BRACKET WINCH FRAME - 4 TON WORM WINCH CABLE ASSEMBLY 6 1 * CAB PROTECTOR WELDMENT -SPECIFY CHASSIS COVER PLATE ANTI-TILT PLATE HOSE TRAY HOSE TRAY BEARING PAD - REFER TO SUBFRAME SECTION LIGHT 2.5" AMBER REFLEX LED (MCL59AB) LIGHT 2.5" RED REFLEX LED (MCL509RB) LIGHT 2.5" GROMMET LED MARKER LIGHT, AMBER (RECT.) STORAGE TRAY MAT - ALL STEEL BODIES FRONT SAFETY CHAIN ASSEMBLY - 5/16" x JUNCTION BOX * CONTACT DISTRIBUTOR FOR ADDITIONAL INFORMATION VI-7

10 STEEL BED ASSEMBLY REMOVABLE RAIL VI-8

11 STEEL BED ASSEMBLY REMOVABLE RAIL REF. NO. PART NO. REQ D NUMBER DESCRIPTION 1 1 * CARRIER BED WELDMENT TON WINCH ASSEMBLY SPACER, WINCH BRACKET WINCH FRAME - 4 TON WORM WINCH CABLE ASSEMBLY 6 1 * CAB PROTECTOR WELDMENT -SPECIFY CHASSIS COVER PLATE ANTI-TILT PLATE HOSE TRAY HOSE TRAY REAR REMOVABLE RAIL - STEEL (19 THRU 21 6) MID REMOVABLE RAIL - STEEL (19 THRU 21 6) 12 2 * FRONT REMOVABLE RAIL - STEEL LYNCH PIN BEARING PAD KIT BEARING PAD KIT - 21 * BEARING PAD KIT HOSE CLAMP WELDMENT LIGHT 2.5" AMBER REFLEX LED (MCL59AB) LIGHT 2.5" RED REFLEX LED (MCL509RB) LIGHT 2.5" GROMMET FRONT SAFETY CHAIN ASSEMBLY - 5/16" x JUNCTION BOX * CONTACT DISTRIBUTOR FOR ADDITIONAL INFORMATION VI-9

12 TILT FRAME ASSEMBLY BEZEL TYPE LH RH TAIL LIGHT HOUSING FASTENER KIT (ONE SIDE) PART QTY NUMBER DESCRIPTION HORIZONTAL S.S VERTICAL S.S HORIZONTAL BLK VERTICAL BLK /8-16 x 1-1/4 CARR. HD. BOLT SS /8-16 HEX NUT SS /8 LOCK WASHER SS BEZEL FASTENER KIT (ONE SIDE) PART QTY NUMBER DESCRIPTION /4-20 x 3/4 RHMS SS /4-20 LUG NUT Z /4 LOCK WASHER SS ITEMS 25, 26, SUBFRAME END CAPS VI-10

13 TILT FRAME ASSEMBLY REF. NO. PART NO. REQ D NUMBER DESCRIPTION TILT FRAME - W/L * TILT FRAME - D/S T/B NWL TAIL LIGHT HOUSING (RH) TAIL LIGHT MTG. BRACKET (RH) ALL SERIES TAIL LIGHT HOUSING (LH) TAIL LIGHT MTG. BRACKET (LH) ALL SERIES L-ARM STORAGE TUBE BRACKET 7 1 PLATE, LIGHT MOUNTING (RH) - See page PLATE, LIGHT MOUNTING (LH) - See page LIGHT 6" OVAL RED LED LIGHT 6" OVAL REVERSE LED LIGHT 6" GROMMET LIGHT 2.5" RED REFLEX LED (MCL59RB) LIGHT 2.5" GROMMET LED LICENSE PLATE ILLUMINATOR LIGHT CONTROL BOX W/BASE AND WIRE TOW LIGHT SOCKET BACK-UP ALARM BACK-UP ALARM GROMMET MODEL JUNCTION BOX CONTROL STA. DECAL, 5 SPOOL (LH) CONTROL STA. DECAL, 5 SPOOL (RH) SAFETY PIN (1-1/4" x 14" CR) SAFETY PIN HDW. ( ) CYLINDER PAD L CONTROL BOX HOOD WELDMENT (LH) R CONTROL BOX HOOD WELDMENT (RH) CONTROL BOX SUPP. CHANNEL (LONG) ITEMS #25, 26, 27 COMPLETE MUD FLAP MTG. BRACKET, STD. LONG (RH) MUD FLAP MTG. BRACKET, STD. LONG (LH) BAR, MUD FLAP SUPPORTS (S.S.) 31 2 * MUDFLAP 24" x 24" MOUNTING FRAME PIN, PIVOT (HINGE) PIN, LIFT CYL & BED EXTENDED SNAP RING 1-1/4" CYLINDER MTG. CROSSMEMBER-TILT FRAME MOUNTING BRACKET TILT CYLINDER PIN TILT PIVOT WELDMENT SUBFRAME END CAP SAFETY CHAIN BEARING PAD KIT - (10 SERIES) VI-11

14 WHEEL LIFT & SLIDE-IN TIRE RESTRAINT ASSEMBLY VI-12

15 WHEEL LIFT & SLIDE-IN TIRE RESTRAINT ASSEMBLY REF. NO. PART NO. REQ D NUMBER DESCRIPTION OUTER BOOM WELDMENT INNER BOOM WELDMENT WHEEL LIFT CYLINDER PIN PIN, EXTEND CYLINDER PIVOT PIN, LIFT CYLINDER WELDMENT WHEEL LIFT CYLINDER BEARING PAD, NYLATRON (INNER BOOM) BEARING PAD (UHMW) 3/16 x 2-3/8 x /8-16 x 1" ALLEN HD SET SCREW Z /8-16 HEX JAM NUT Z INNER CROSSBAR WELDMENT /8-16 x 3/4" BUTTON HEAD CAP SCREW WASHER, PIVOT PIN RETAINER GREASE FITTING, STRAIGHT O-RING 1" ID x 1-1/4" OD x 1/8" PIVOT PIN, W/L CROSSBAR BALL, CHROME 1" (GRADE 16) SPACER, CROSSBAR DETENT SPRING, DIE PIPE PLUG PIVOT PIN (REAR)-EXTEND CYLINDER ENCAPSULATING CAGE, INNER L OUTER XTUBE ASSEMBLY (LH) R OUTER XTUBE ASSEMBLY (RH) L-ARM STRAP, RATCHET PIVOT ASSEMBLY ENCAPSULATING CAGE (TOP) STINGER STOP BLOCK BEARING PAD VI-13

16 HYDRAULICS VI RETURN

17 HYDRAULICS REF. NO. PART NO. REQ D NUMBER DESCRIPTION OIL RESERVOIR WINCH MOTOR, 4 TON WINCH MOTOR, 5/6 TON 3 1 * PTO PUMP (15 GPM) BED TILT CYLINDER LOCK VALVE HYD. FITTING 3/4" MORB x 3/4" FP WHEEL LIFT LOCK VALVE CYLINDER, WHEEL LIFT UP/DN CYLINDER, BED TILT VALVE BODY, 5 SPOOL CYLINDER, WHEEL LIFT EXTEND CYLINDER, BED EXTEND SIGHT GLASS CAP, OIL RESERVOIR 15 * SKUFF JACKET HYDRAULIC FITTING 8MJ-16MB HYDRAULIC FITTING 1" HOSE BARB MB HYDRAULIC FITTING 6MJ-8MB 90 DEG HYDRAULIC FITTING 8MJ-8MJ HYDRAULIC FITTING 8MJ-8MP 90 DEG HYDRAULIC FITTING 6MJ-6MP 45 DEG HYDRAULIC FITTING 6MJ-6MB 90 DEG HYDRAULIC FITTING 4FP-4FP-4MP BRANCH "T" HEX BUSHING 3/8" x 1/4" (151157X) HYDRAULIC FITTING 6MJ-4MP 90 DEG LOCK ON STEM, 3/4" MALE NPT HOSE RETURN 3/4" x 20 LONG HOSE SUCTION 1" x 11 LONG HYDRAULIC FITTING 1" HOSE BARB MP HYDRAULIC FITTING 1" 90 DEG. STREET ELL HOSE 4M2T-6FJX-6FJX 1/4 x HOSE 4M3K 6FJX-6FJX 1/4 x HOSE 4M3K 6FJX-6FJX 1/4 x HOSE 8M3K 8FJX-8FJX 1/2 x HOSE 4M3K 6FJX-6FJX 1/4 x HOSE 8M3K 8FJX-8FJX 1/2 x HOSE 8M3K 8FJX-8FJX 1/2 x HYDRAULIC FITTING 6MJ-6MB HYDRAULIC FITTING 8MJ-10MB HYDRAULIC FITTING 6MJ-8MB IMMERSION FILTER ASSY IMMERSION FILTER ELEMENT 42 2 * WINCH HOSES * CONTACT DISTRIBUTOR FOR ADDITIONAL INFORMATION VI-15

18 CONTROL & CROSSROD ASSEMBLY VI-16

19 CONTROL & CROSSROD ASSEMBLY REF. NO. PART NO. REQ D NUMBER DESCRIPTION CONTROL KNOB, BLUE SB/B - TILT, SP CONTROL KNOB, RED, PRIMARY WINCH BRACKET, CONTROL HANDLE CONTROL KNOB, GRAY W/L EXT/UP-DW SPOOL CONTROL VALVE SPRING, ANTI-RATTLE END CAP, CONTROL HANDLE ROD /8-16 x 3/4" HHCS GR5 Z /8-16 x 4" HHCS GR5 Z /8-16, J-NUT TINNERMAN /8-16 NYLON LOCK NUT Z /8-16 HEX JAM NUT Z /16" SAE FLAT WASHER Z /8" LOCK WASHER Z /16" x 1" CLEVIS PIN Z BOWTIE - Z ROD, CONT. HANDLE 5 SPOOL UHMW ANGLE CONTROL HANDLE (FWD. INNER) LONG CONTROL HANDLE (FWD. OUTER) LONG CONTROL HANDLE (REAR INNER) LONG CONTROL HANDLE (REAR OUTER) LONG CONTROL ROD WELDMENT CONTROL ROD LINK CONTROL ROD WELDMENT (ANTI-TILT) CONTROL HANDLE WELDMENT (CTR) LONG VI-17

20 4-TON HYDRAULIC WINCH VI-18

21 4-TON HYDRAULIC WINCH REF. NO. PART NO. REQ D NUMBER DESCRIPTION LEVER COUPLING DRUM YOKE SCREW GASKET KEY SCREW KEY SHAFT CLUTCH HOUSING BUSHING SCREW SPRING BALL SPACER PLUG HOUSING PLUG REDUCER DRAG BRAKE SPRING SCREW CAP BEARING WORM SEAL HUB GEAR WASHER SCREW GASKET COVER SCREW CAP ADAPTER SCREW KEY SHAFT KEY CLUTCH TORSION SPRING * TON WORM WINCH ASSEMBLY * When ordering specify winch serial number. VI-19

22 WINCH CLUTCH CONTROL REF. NO. PART NO. REQ D NUMBER DESCRIPTION GREASE FITTING, "T" HANDLE ADJUSTING YOKE SCREW, 5/16"-18 x 1/2" SQ HD SET SCREW, 3/8"-16 x 1" HEX HD CAP NUT, 3/8"-16 NYLOK NUT, 1/2"-13 JAM WASHER, 1/2" FLAT PIN, 1/2" x 1-1/2" CLEVIS PIN, 1/8" x 1-1/4" COTTER PIN, 5/32" x 1" ROLL MOUNTING ANGLE CONTROL ROD BELL CRANK WINCH CLUTCH CONTROL ASSEMBLY VI-20

23 BED LOCK ASSEMBLY REF. NO. PART NO. REQ D NUMBER DESCRIPTION BED LOCK WELDMENT BED LOCK HOLD-DOWN MOUNTING BRACKET BOLT, 1/2-13 x 1-1/2 HHCS ZP GRADE NYLON LOCK NUT, 1/2-13 ZP FLAT WASHER, 1/2 ZP BOLT, HHCS 5/8-11 x 2 ZP GRADE NUT, 5/8-11 NYLON LOCK ZP FLAT WASHER 5/8 ZP CARRIAGE BOLT 5/8-11 x 1-3/4 ZP GRADE BED LOCK ASSEMBLY VI-21

24 CABLE TENSIONER ASSEMBLY (STANDARD 4-TON WINCH) 7 REF. NO. PART NO. REQ D NUMBER DESCRIPTION TENSIONING SPRING SCREW, 3/8"-16 x 1" HEX HD CAP SCREW, 3/8"-16 x 3-1/2" HEX HD CAP WASHER, 3/8" FLAT NUT, 3/8"-16 HEX NYLOK ROLL PIN, 3/8" x 1" TENSIONING PLATE CABLE TENSIONER BRACKET CABLE TENSIONER ASSEMBLY VI-22

25 CABLE ROLLER ASSEMBLY REF. NO. PART NO. REQ D NUMBER DESCRIPTION CABLE ROLLER ASSEMBLY SCREW, 1/2"-13 x 1-1/4" HEX HD NUT, 1/2"-13 NYLOK CABLE ROLLER GUIDE WELDMENT DOCK STABILIZER REF. PART NO. NUMBER DESCRIPTION DOCK STABILIZER WELDMENT VI-23

26 PTO Beacon Flash Work Up Work Down Section VI - PARTS (cont d) OPTIONAL DASHBOARD PANEL Ignition (Red) Power UP Switch Panel (backside) Battery High Amp Circuit Breaker From Factory Harness Marker Left Turn Right Turn Back Up Auxilary Power Protector 10 position Junction Box Battery Left Turn Right Trun Back Up 40A 20A 20A 20A VI-24

27 HYDRAULIC CYLINDERS REF. NO. PART NO. REQ D NUMBER DESCRIPTION CYLINDER, BED EXTEND SEAL KIT, BED EXTEND REF. NO. PART NO. REQ D NUMBER DESCRIPTION CYLINDER, BED TILT SEAL KIT, BED TILT VI-25

28 HYDRAULIC CYLINDERS REF. NO. PART NO. REQ D NUMBER DESCRIPTION CYLINDER, WHEEL LIFT EXTEND SEAL KIT, WHEEL LIFT EXTEND REF. NO. PART NO. REQ D NUMBER DESCRIPTION CYLINDER, W/L UP/DOWN SEAL KIT, W/L UP/DOWN VI-26

29 LIGHT KIT REF. PART NO. NUMBER DESCRIPTION LIGHT 6" OVAL RED LED LIGHT 6" OVAL REVERSE LED LIGHT 6" OVAL GROMMET REF. PART NO. NUMBER DESCRIPTION LIGHT 6" OVAL RED LED LIGHT 6" OVAL REVERSE LED LIGHT 6" OVAL GROMMET VI-27

30 LIGHT KIT REF. PART NO. NUMBER DESCRIPTION LED LIGHT, AMBER MARKER, RECTANGULAR (COMPLETE) LED LIGHT, RED MARKER, RECTANGULAR (COMPLETE) REF. PART NO. NUMBER DESCRIPTION A LIGHT, AMBER MARKER, RECTANGULAR (COMPLETE) R LIGHT, RED MARKER, RECTANGULAR (COMPLETE) VI-28

31 LIGHT KIT REF. PART NO. NUMBER DESCRIPTION LIGHT 3/4" RED 3 PACK LED W/GROMMET VI-29

32 OPTIONAL LIGHTING ACCESSORIES REF. NO. PART NO. REQ D NUMBER DESCRIPTION SPOT LIGHT W/GASKET GROMMET, RUBBER #10-24 x 1" MACHINE SCREW NUT, 3/8"-16 HEX NYLOK RUBBER CUSHION "T" BOLT ADAPTER VI-30

33 X

34 OPTIONAL OUTER CROSSTUBE & 3-WAY PIVOT TIRE RESTRAINT ASSEMBLY /4 VI-31

35 OPTIONAL OUTER CROSSTUBE & 3-WAY PIVOT TIRE RESTRAINT ASSEMBLY REF. NO. PART NO. REQ D NUMBER DESCRIPTION OUTER XTUBE ASSY. LH(PIVOT) (COMPLETE) OUTER XTUBE ASSY. RH(PIVOT) (COMPLETE) RESTRAINT TIRE, LH (PIVOT) RESTRAINT TIRE, RH (PIVOT) NYLON POLY-COAT STRAP (PIVOT) END PL, LH (CSTG) PIVOT END PL, RH (CSTG) PIVOT PIN ASSEMBLY PIN, PIVOT /8" INTERNAL TOOTH L/W Z /8-16 x 3/4" FLAT HD. CAP SCREW PLUG, DRY-OUT HOLE GREASE FITTING STRAIGHT ALIGNMENT PIN T HANDLE (ALUMINUM) ANGLE STYLE SPRING, PIVOT PIN, PLUNGER /32 x 1" TENSION PIN Z TARP STRAP C L-ARM STORAGE TUBE (BLACK) - NOT SHOWN C L-ARM STORAGE TUBE (GALV) - NOT SHOWN VI-32

36 Section V I- PARTS (cont'd) AUTOGRIP II COMPONENTS REF NO PART NO. REQ'D NUMBER DESCRIPTION OUTER BOOM WELDMENT INNER BOOM WELDMENT WHEEL LIFT HINGE PIN BEARING PAD, NYLATRON LOWER LIFT CYLINDER PIN (W/L) UPPER LIFT CYLINDER PIN (W/L) BEARING PAD, NYLATRON NUT, 3/8"-16 HEX NYLOK /8-11" x 2" HEX HD BOLT NUT, 5/8-11" HEX NYLOCK GREASE FITTING, STRAIGHT EXTEND CYLINDER MTG. PIN, 0.980" x 6-11/16" H BEARING PAD, NYLATRON ROD END KEEPER PIN SCREW, 3/8"-16 x 1-1/4" HEX HD CAP SCREW, 3/8"-16 x 2-1/2" HEX HD CAP A9 3/8" x 1 ROUND HEAD BOLT /8" FLAT WASHER VI-33

37 Section VI - PARTS (cont'd) AUTOGRIP II COMPONENTS REF NO PART NO. REQ'D NUMBER DESCRIPTION CROSSBAR WELDMENT CL WHEEL RETAINER - LEFT CR WHEEL RETAINER - RIGHT WHEEL RETAINER CYLINDER PIN ARM PIVOT PIN L WHEEL SPACER - LEFT R WHEEL SPACER - RIGHT HOSE GUARD SCREW-PLUG CROSSBAR DETENT CROSSBAR PIN SNAP RING INCH INTERNAL L WHEEL RETAINER CYLINDER - LEFT R WHEEL RETAINER CYLINDER - RIGHT L-ARM CYLINDER END BLOCK T-PIN 5/8 x AUTOGRIP ARM CHAIN /16 x 1-1/4 SHOULDER SHCS 1/4-20 UNC /4-20 UNC NYLON LOCK NUT A5 3/8 ALLEN BOLT /8 NYLON LOCK NUT /4 NYLON LOCK NUT CHAIN CLEVIS /16 x 1 SHOULDER SHCS 1/4-20 UNC /4-20 UNC NYLON LOCK NUT /16 FLAT WASHER I SNAP-RING INCH INTERNAL BASKET TIRE STRAP - AUTO BASKET TIRE STRAP - TRUCK VI-34

38 OPTIONAL CAB RACK ASSEMBLY VI-35

39 OPTIONAL CAB RACK ASSEMBLY REF PART # DESCRIPTION QPU FRAME-GM KODIAK, INTERNATIONAL FRAME-INTERNATIONAL 4400, KENWORTH 1 FREIGHTLINER FL FRAME-FORD F STEEL DECK-STANDARD STEEL DECK-SETBACK ALUMINUM DECK-STANDARD ALUMINUM DECK-SETBACK L HINGE PLATE-LEFT R HINGE PLATE-RIGHT CYLINDER BRACKET HINGE PIN L LIFT CYLINDER-LEFT R LIFT CYLINDER-RIGHT CYLINDER PIN-TOP CYLINDER PIN-BOTTOM L INT'L/FORD FRONT MOUNTING BRACKET-LEFT M2L FREIGHTLINER M2 FRONT MTG BRACKET-LEFT KWL KENWORTH FRONT MOUNTING BRACKET-LEFT R INT'L/FORD FRONT MTG BRACKET-RIGHT M2R FREIGHTLINER M2 FRONT MTG BRKT-RIGHT KWR KENWORTH FRONT MOUNTING BRACKET-RIGHT L REAR MOUNTING BRACKET-LEFT GENERIC L2 REAR MGT BRKT-LEFT LARGE INT'L FUEL TANK M2L REAR MOUNTING BRACKET-LEFT M R REAR MOUNTING BRACKET-RIGHT GENERIC M2R REAR MOUNTING BRACKET-RIGHT M SAFETY CHAIN HOOK PLANETARY WINCH WINCH CABLE 3/8 x 62 FT ALUMINUM BEZEL GROMMET-MARKER LIGHT A MARKER LIGHT-AMBER GROMMET-TURN SIGNAL TURN SIGNAL-AMBER BOLT 3/4-10 UNC x 3 GRADE NYLON LOCK NUT 3/4-10 UNC FLAT WASHER 3/4 8 VI-36