DCV MONOBLOCK AND MODULAR VALVES. Technical Catalogue

Transcription

1 CV MONOLOCK N MOLR VLVES echnicl Ctlogue July 216

2 i echnicl informtion INROCION Red this instructions crefully efore instlltion. ll opertions must e crried out y qulified personnel following the instructions. he user must periodiclly inspect, sed on the conditions of use nd the sustnces used, the presence of corrosion, dirt, the stte of wer nd correct function of the vlves. OIL VISCOSIY CCORING O EMERRE E mm²/s HYRLIC FLI se only minerl oil (HL, HL) ccording to IN se of other different fluids my dmge the good opertion of the vlve ISO VG 1 ISO VG 68 ISO VG 6 ISO VG 32 VISCOSIY he oil viscosity must e in the rnge of 1 mm²/s to 5 mm²/s. Recommended oil viscosity 6 mm 2 /s (32 mm 2 /s for Crtridge vlves) le 1: ISO viscosity grdes ISO VG 22 Viscosity grde verge kinemtic viscosity C Kinemtic-viscosity limits C min. mx. ISO VG ISO VG ISO VG ISO VG C F ISO VG ISO VG ISO VG = Vlues used in the chrt Oil viscosity ccording to temperture CONVERSION LE SS / E / mm²/s SS E mm²/s CONMINION Oil contmintion is the min cuse of fults nd mlfunction in hydrulic systems. rsive prticles in the fluid erode or lock moving prts, leding to system mlfunction. he vlves we re offering do not require filtering chrcteristics ny higher thn those needed for usul hydrulic components such s pumps, motors, etc. However, ccurte filtering does gurntee reliility nd long life to ll the system s hydrulic prts. Relile performnce nd long working life for ll oil-pressure prts is ssured y mintining the level of fluid contmintion within the limits specified in the dt sheet of the vlve. Hydrulic fluid must lso e clened properly efore filling the hydrulic circuit, especilly when commissioning new system, s this is when the oil contmintion generlly peks due to its flushing effect on the components, nd the running-in of the pump. Mximum contmintion level is required on dtsheet of the vlve ccording to ISO 6:1999. In the following tle there is the correspondence etween ISO 6:1999 nd old stndrd NS 1638 for informtion purpose: he stndrd ISO 6:1999 defines the contmintion level with three numers tht relte with the numer of prticles of verge dimension equl or greter thn μm, 6 μm e 1 μm, in 1 ml of fliuid. In following tle there is reference to reccomended contmintion level nd correspondence with old NS 1638 stndrd. 2 IE/CV-INFO/3-216

3 echnicl informtion le 2: Reccomnded contmintion level. Oil filtrtion recommendtions ype of system Clenliness clss recommended ype of vlve NS 1638 ISO 6 : 1999 ( * ) Systems or components operting t HIGH RESSRE > 25 r (36 psi) HIGH Y CYCLE LICIONS Systems or components with LOW dirt tolernce Systems or components operting t MEIM / HIGH RESSRE Systems nd components with moderte dirt tolernce Systems or components operting t LOW RESSRE < 1 r (15 psi) LOW Y CYCLE LICIONS Systems nd components with GOO dirt tolernce solute filtrtion micron rting ( ) 18 / 16 / / 17 / / 18 / * Contmintion clss NS 1638: it is determined y counting the totl prticles of different size rnges contined in 1 ml of fluid. solute filtrtion: it is chrcteristic of ech filter, it refers the size (in micron) of the lrgest spericl prticle wich my pss through the filter. WORKING EMERRES mient temperture rnge: -25 C to +6 C Fluid temperture rnge (NR sels): -25 C to +8 C herml shocks cn ffect the performnce nd the expected life of the product, hence it is necessry to protect the product from these conditions. ELECRICL OWER SLY he comintion of permnent overvoltge nd very hot tempertures cn stress the solenoid. herefore lwys good het dissiption nd voltge level hs to e ssured. INSLLION he feet of the vlve must lwys nd perfectly rest on plne surfce. o not tmper the tie rod nuts (control vlves) to void dmging the distriutor. Oserve the size of the fitting threds. o not use solvents to void dmging the ruer prts of the vlves. SE N MINENNCE Oserve the functionl limits indicted in the technicl ctlogue On periodic sis nd sed on the conditions of use, check for clenliness, stte of wer or frctures nd correct performnce of the vlve. If the O-rings re dmged, replce them with those supplied y the mnufcturer. o ssure the est working conditions t ll time, check the oil nd replce it periodiclly (fter the first 1 working hours nd then fter every 2 working hours or t lest once every yer). ttention: ll instlltion nd mintennce intervention must e performed y qulified stff. i SELS O-rings mde in crylonitrile utdiene (NR) re normlly fitted on the vlves. he ckup rings tht protect the O-rings re lso mde in NR, or sometimes FE. oth the O-rings nd the ckup rings re suitle for the working tempertures mentioned ove. For different tempertures, contct our sles deprtment. RNSOR N SORGE he vlve must e hndled with cre to void dmge cused y impct, which could compromise its efficiency. In the cse of storge, keep the vlves in dry plce nd protect ginst dust nd corrosive sustnces. When storing for periods of more thn 6 months, fill the vlve with preserving oils nd sel it. CONVERSION CHR ype SI units lterntive units Conversion fctor Force Newton (N) [kgm/s²] Kilogrm force (kgf) 1 kgf = 9.87 N pound force (lf) [lf/s²] 1 lgf =.8 N millimeter (mm) [1 m] inch (in) 1 in = 25. mm Length meter (km) [1 m] yrd (yd) [3ft] 1 m = yd kilometer (km) [1 m] mile (mile) [176 yd] 1 mile = 1.69 km orque Newton meter (Nm) pound force.feet (lf.ft) 1 lf.ft = Nm ower kilowtt (kw) [1 Nm/s] horsepower (hp) 1 kw = 1.31 hp metric horsepower (CV) 1 kw = 1.36 CV r 1 M = 1 r ressure Megscl (M) [ N/mm²] psi (lf/ln²) 1 M = 15 psi ton/f/ln² 1 ton/f/ln² = 15.5 M Flow rte liter/min (l/min) K gl/min 1 K gl/min =.56 l/min S gl/min 1 S gl/min = l/min Celsius ( C) Frenheit ( F) 1 F = 1.8 C+32 emperture F C IE/CV-INFO/

4 Generl specifictions i MIN CHRCERISI ll the production VS revini wnt to e high qulity production. Infct the project of ech single vlve nd the choice of the etter mterils, mchined with the highest tecnologies nd under the strongest controls in ech process, llow highest chrcteristics nd numerous pplictions descried in the following pges. Furthermore: 1. ll the csting re mde in Shell-Moulding, in specil grphite cst iron. his kind of cst iron is in higt resistnce, nd it llows to hve, with the sme externl overll dimensions, igger internl gllery, nd lower pressure drops; 2. ll spools re mde in high resistnce steel, nichel plted, rdil lnced nd with specil notches in order to hve etter sensiility; 3. ll springs re mde in high resistence steel. ressure setting springs re pressed efore testing;. mx tolernce of spool housing is 2 micron; 5. internl lekge t 12 r, 5 C nd oil 3 cst is eetwen 1 nd 2 cm³/min, depending from the kind of spool nd the kind of vlve. Fetures Circuit Min relief v. ort relief vlves hreds Spool stroke GENERL CONIION OF WORK Mx working temperture -25 C +8 C Suggested working temperture +3 C +6 C Mx ck pressure Mx contmintion level Fluid oil Kinemtic viscosity 2 r (29 SI) NS 1638 clss 9 (19/16 ISO-6) Minerl oil 1 6 mm²/s Filtrtion Spool re ville with different metering, mrine protected, Viton sels, specil spring, etc. MONOLOCK VLVES MOLR VLVES CV 2 CV CV 3 CV 5 CV 8 CV MG Mx section N.o Mx flow l/min GM Mx pressure R psi rllel Series ndem irect iloted Overlod nti cvittion Comined - 3/8 1/2 3/ 1 3/8 1/2 3/8 1/2 3/ S 1/2 3/ 1 3/8 3/8 1/2 ISO 228/1 3/8 1/2 3/ Cvity ISO /2 3/8 (3) 1/2 (3) 3/ (3) 1 3/8 3/8 1/2 3/ 1/2 3/ () 1/2 3/ 3/ 1 3/ -16NF 1 1/16-12N SE ISO 263 Cvity - (Stndrd) 9/16-18NF (SE 6) 9/16-18NF (SE 6) (SE 8) 7/8-1NF (SE 1) 3/ -16NF (SE 8) 7/8-1NF (SE 1) 3/ -16NF (SE 8) 7/8-1NF (SE 1) 9/16-18NF (SE 6) 9/16-18NF (SE 6) 7/8-1NF (SE 1) 7/8-1NF (SE 1) (SE 12) 7/8-1NF (SE 1) 1 1/16-12N (SE 12) 7/8-1NF (SE 1) 1 1/16-12N (SE 12) (3) 7/8-1NF (SE 1) (1-3) 1 1/16-12N (SE 12) 1 5/16-12N (SE 16) 1 5/16-12N (SE 16) 9/16-18NF 7/8-1NF 9/16-18NF (SE 6) (SE 6) (3) 3/ -16NF (SE 1) (3) 1 1/16-12N 1 5/16-12N (SE 16) (SE 8) (SE 12) () 3/ -16NF 1 1/16-12N (SE 8) (SE 12) mm ± 5 ± 5 ± 5 ± 5 ± 7 ± 8 inch ±.2 ±.2 ±.2 ±.2 ±.28 ±.31 th position mm inch Series mm ±.5 ±.5 ± 5.5 ± 8 inch ±.18 ±.18 ±.22 ±.31 threds villes on request threds villes on requestsolo only for outlet side (3) inlet section with top output () output section with stndrd upper thred + crry over (see pge 61) IE/CV-INFO/3-216 hreds villes on request

5 Moile vlves CV OVERLL IMENSIONS 22 [.87] 1,5 [.57] 3 [1.3] 17 [.67] 12 [.7] 11,5 [.5] 29,5 [1.16] 37 [1.6] C 37 [1.6] 3 [1.18] 1 17 [.67] 19 [.75] 25 [.98] 3 [1.3] 53,5 [2.11] 17 [.67] [.7] [3,19] 1,5 [1.63] 15 [.13] 29 [8.23] 22 [.87] 21 [.83] 62 [2.] 1 [1.61] [1.73] Overlod vlve (optionl) 2,8 [.82] MONOLOCK M1 Ø8,5 [.33] 12 [.7] 62,5 [2.6] 23 [.91] 89 [3.5] 5 [1.77] ª OS. mm [inch] ype C mm [inch] mm [inch] Weight kg [l] Mx flow l/min [GM] Mx pressure R [psi] CV /1 12 [.2] 73 [2.87] 3.57 [7.85] CV /2 139 [5.7] 11 [.33] 5.5 [11.99] CV /3 CV / 176 [6.93] 213 [8.39] 17 [5.79] 18 [7.2] 7.3 [16.6] 9.15 [2.13] 7 [18.5] [58] CV /5 25 [9.8] 221 [8.7] 11. [2.2] CV /6 287 [11.3] 258 [1.16] [28.27] IE/CV-MONOLOCK/

6 Moile vlves CV CHRCERISIC RESSRE RO FLOW CRVES Inlet pressure drop etween spool in centrl position MONOLOCK psi r N.o sections l/min S.GM Inlet pressure drop etween () spool in working position psi r ( 6) 1 ( 1) N.o sections l/min S.GM Inlet pressure drop etween () spool in working position psi r ( 1) N.o sections ( 6) l/min S.GM Metering curves re different for ech typee of spool. herefore prticulr curves re supplied on request he curves re otined using stndrd doule cting spool (cod. S1) with oil t 5 C nd viscosity 36 mm² / s 8 IE/CV-MONOLOCK/3-216

7 Ordering code Model Inlet section Working sections (repet for ny section) Outlet section hreds CV / * IS* * (*) S V(*) W* Xn * F* escription ge Size: CV2 CV N.o working sections 5-7 Inlet type 11 Vlves rrngement 12 Min relief vlve setting 12 Spools 13 Control side 1 ositioning / Control side 19 Service port vlves 2 Overlod vlve setting 2 Hnd lever 2 Working section repeted for n. times 2 Outlet 25 hreds 25 MONOLOCK Optionl fields. Not specify if not required. Service port vlves optionl, is required specil monolock ody. HYRLIC SCHEME V Working sections Outlet section IS S S S 1 Side (ositioning / Control) Inlet section Side (Control) Inlet section Working sections Outlet section IE/CV-MONOLOCK/

8 Ordering code ORERING COE EXMLE MONOLOCK CV/3 IS S1 1 V1(15) W2 X2 S1 1 W2 S F CV/3 - CV 3 sections monolock IS - op inlet - irect min relief vlve + Solenoid dump vlve 2V N. Open - Vlve setting 2 R S1 - Spool, 3 position, doule cting 1 - Spool control side - Spool control side, 3 pos. spring centred spool, detent in V1(15) - Overlod vlve in position - Setting 15 r W2 - Stndrd hndle lever X2 - Working section repeted for n. 2 times S1 - Spool, 3 position, doule cting 1 - Spool control side - Spool control cp side, 3 pos. spring centred spool, detent in W2 - Stndrd hndle lever S - op outlet F - 1/2 S threds 1 IE/CV-MONOLOCK/3-216

9 Inlet sections Inlet type CV/* IS* * (*) S V W* Xn * F* IS* Inlet type IS escription op inlet (stndrd) rwing IS S S S 1 MONOLOCK ISL Side inlet ISL S S S 1 On request. RIGH inlet section with top inlet (I). Contct our sles deprtment. On request. RIGH inlet section with side inlet (IL). Contct our sles deprtment. IE/CV-MONOLOCK/

10 Inlet sections Vlves rrngement Min relief vlve setting (r) Vlves choice MONOLOCK 58 [2.28] CV/* IS * * (*) S V W* Xn * F* * (*) * (*) Vlves rrngements nd min relief vlve setting * * * CV CV2 rrngements Specify pressure relief vlve setting (from 2 to r). In the order it is suggested specify the flow rte. 7,75 [2.79] 63,5 [2.5] 63 [2.8] 7,27 [2.77] 21 [.83] 53,5 [2.11] 2 1,5 1 [1.61] 17,5 [.69] [.79] [.6] 58,5 [2.3] CV2 CV 1 S irect min relief vlve Vlve set with plug S Solenoid dump vlve 12V work NORMLLY OEN Solenoid dump vlve 2V work NORMLLY OEN Solenoid dump vlve 26V work NORMLLY OEN Solenoid dump vlve 3V work NORMLLY OEN Solenoid dump vlve 12V work NORMLLY CLOSE Solenoid dump vlve 2V work NORMLLY CLOSE Solenoid dump vlve 26V work NORMLLY CLOSE Solenoid dump vlve 3V work NORMLLY CLOSE lug - Stndrd (position selectet with IS or ISL) ressure guge connection G 1/ (replce the plug selected with IS or ISL) Include lock (CV ) nd specil monolock ody S (3) Solenoid fetures 12 Vdc 2 Vdc 26 Vdc 3 Vdc Nominl power 17 W 2 W 2 W 17 W Connector IN 365 ISO rotection degree I65 mient temperture C (3) (3) 12 IE/CV-MONOLOCK/3-216

11 Working sections Spool CV/* IS * * (*) S V W* Xn * F* IS S S S 1 MONOLOCK S Spool escription Symol escription Symol S1 S1G 3 position, doule cting S9 3 positions, single cting in - open S2 3 positions, doule cting, - Lc locked - nd open S1 3 positions, single cting in - open S3 3 positions, doule cting, - Lc locked - nd locked S11 3 positions, doule cting regenertive in (not stndrd) S SG 3 positions, doule cting, - nd open S36 3 positions, doule cting regenertive in (not stndrd) S5 S5G 3 positions, doule cting, - open - locked S12 positions, doule cting with th flot position S6 S6G 3 positions, doule cting, - locked - open S23 2 positions with function ded mn (unctivted) in position ; working position in S7 3 positions, single cting in S2 2 positions with function ded mn (unctivted) in position ; working position in S8 3 positions, single cting in S27 2 positions with function ded mn (unctivted) in position ; working position in S28 2 positions with function ded mn (unctivted) in position ; working position in SG = Extr metering IE/CV-MONOLOCK/

12 Working sections Spool control side CV/* IS * * (*) S V W* Xn * F* MONOLOCK IS S S S 1 Spool control side escription rwing 1 1 Stndrd hndle C C 1 1 mm inch CV M CV M Hndle t 18 C 2 2 C 2 2 mm inch CV M CV M Without hndle C mm inch CV Ø C CV Hydrulic control - Mx pilot pressure 35 r 58 psi mm inch CV / S CV / S Hydrulic lever control 53 C C C mm inch CV / S = luminium version (only CV) 1 IE/CV-MONOLOCK/3-216

13 Working sections Spool control side escription rwing Sfety hndle locked in neutrl position Sfety hndle locked in position CV CV CV CV MONOLOCK Security hndle locked in position 7 7 CV CV Security hndle locked in position nd CV CV Security hndle locked in th position 9 9 ª CV CV ny positions detented lever CV = luminium version (only CV) IE/CV-MONOLOCK/

14 Working sections Spool control side escription rwing Cloche control with fulcrum on upstrem section 1 1 MONOLOCK 1 (CX) Cloche control with fulcrum on downstrem section 1 1 L L mm inch CV CV (CX) L L mm inch CV CV Cloche control with fulcrum turned 18 on the downstrem section (CX) L CV CV L Cloche control with fulcrum turned 18 on the upstrem section (CX) L CV CV L Flexile cle control 1 M6 M16x1.5 CV CV (CX) code required to use on 2th section Cle supplied on request. Lenght cle nd control, contct our commercil dept 16 IE/CV-MONOLOCK/3-216

15 Working sections Spool control side escription Spool stroke djustment in rwing Spool stroke djustment in, hndle t 18 mm inch CV CV mm inch CV CV MONOLOCK Stndrd hndle with microswitch in nd rotection degree: I67 Nominl rting:.1 1 / 25VC Minimum rting: 1 m / VC Operting temperture: C Cle length: 5 cm [19.69 inch] mm inch CV CV Stndrd hndle with microswitch in rotection degree: I67 Nominl rting:.1 1 / 25VC Minimum rting: 1 m / VC Operting temperture: C Cle length: 5 cm [19.69 inch] mm inch CV CV Stndrd hndle with microswitch in rotection degree: I67 Nominl rting:.1 1 / 25VC Minimum rting: 1 m / VC Operting temperture: C Cle length: 5 cm [19.69 inch] mm inch CV CV Stndrd hndle with microswitch in th position rotection degree: I67 Nominl rting:.1 1 / 25VC Minimum rting: 1 m / VC Operting temperture: C Cle length: 5 cm [19.69 inch] ª 2 2 mm inch CV CV = luminium version (only CV) IE/CV-MONOLOCK/

16 Working sections Spool control side escription rwing MONOLOCK Hndle 18 with microswitch in nd rotection degree: I67 Nominl rting:.1 1 / 25VC Minimum rting: 1 m / VC Operting temperture: C Hndle 18 with microswitch in rotection degree: I67 Nominl rting:.1 1 / 25VC Minimum rting: 1 m / VC Operting temperture: C Cle length: 5 cm [19.69 inch] Cle length: 5 cm [19.69 inch] mm inch CV CV mm inch CV CV Hndle 18 with microswitch in rotection degree: I67 Nominl rting:.1 1 / 25VC Minimum rting: 1 m / VC Operting temperture: C Cle length: 5 cm [19.69 inch] mm inch CV CV Hndle 18 with microswitch in th position rotection degree: I67 Nominl rting:.1 1 / 25VC Minimum rting: 1 m / VC Operting temperture: C Cle length: 5 cm [19.69 inch] ª 2 2 mm inch CV CV = luminium version (only CV) 18 IE/CV-MONOLOCK/3-216

17 Working sections ositioning / Control side CV/* IS * * (*) S V W* Xn * F* IS S S S MONOLOCK ositioning / Control side escription rwing positions, spring centred spool 1 1 CV CV positions, spring centred spool, detent in nd 2 2 CV CV positions, spring centred spool, detent in 3 3 CV CV positions, spring centred spool, detent in CV CV positions, spring centred spool, detent in th position ª ª ª 5 5 CV CV = luminium version (only CV) IE/CV-MONOLOCK/

18 Working sections ositioning / Control side escription rwing MONOLOCK positions, spring centred spool, sensitive th position, without detent ª 3 positions, spring centred spool, detent in - - ª 6 6 CV CV CV CV positions ( - ), spring centred spool 8 8 CV CV positions ( - ), spring centred spool 9 9 CV CV positions ( - ), spring centred spool, detent in 1 1 CV CV positions ( - ), spring centred spool, detent in CV CV positions free (without spring) CV CV = luminium version (only CV) 2 IE/CV-MONOLOCK/3-216

19 Working sections ositioning / Control side escription rwing rerrnged for doule control ON-OFF pneumtic control - ilot pressure 5-1 r psi Electroidrulic ON-OFF control. Voltge 12Vdc with pressure reducing vlve - ilot pressure 2 r 29 psi mm inch CV M6 CV M8 mm inch CV /8 S CV /8 S CV MONOLOCK CV G 1/8 3.5 [1.36] Connector wires 3 cm rotection degree I65 mient temperture C Nominl power 1 W Electroidrulic ON-OFF control. Voltge 12Vdc without pressure reducing vlve - ilot pressure 2 r 29 psi G 1/8 CV CV G 1/8 Connector wires 3 cm rotection degree I65 mient temperture C Nominl power 1 W Electroidrulic ON-OFF control. Voltge 2Vdc with pressure reducing vlve - ilot pressure 2 r 29 psi CV CV G 1/8 3.5 [1.36] Connector wires 3 cm rotection degree I65 mient temperture C Nominl power 1 W Electroidrulic ON-OFF control. Voltge 2Vdc without pressure reducing vlve - ilot pressure 2 r 29 psi G 1/8 CV CV G 1/8 Connector wires 3 cm rotection degree I65 mient temperture C Nominl power 1 W. = luminium version (only CV) Vlid only for the first section with electroidrulic control. For proper opertion it is required pressure of 8 r (116 psi) mesured t the input or 1. IE/CV-MONOLOCK/

20 Working sections ositioning / Control side escription rwing Electroidrulic ON-OFF control. Voltge 12Vdc - ilot pressure 2 r 29 psi CV MONOLOCK 19 (3) 1 1 Electroidrulic ON-OFF control. Voltge 2Vdc - ilot pressure 2 r 29 psi CV Connector wires 3 cm rotection degree I65 mient temperture C Nominl power 1 W CV (3) 1 1 CV Connector wires 3 cm rotection degree I65 mient temperture C Nominl power 1 W ON-OFF electro pneumtic control. Voltge 12Vdc - ilot pressure 5-1 r psi Ø6 CV Ø6 CV Connector IN 365- ISO6952 rotection degree I65 mient temperture -2 + C Nominl power 8 W ON-OFF electro pneumtic control. Voltge 2Vdc - ilot pressure 5-1 r psi Ø6 CV Ø6 CV Connector IN 365- ISO6952 rotection degree I65 mient temperture -2 + C Nominl power 8 W ON-OFF electro pneumtic control. Voltge 26Vdc - ilot pressure 5-1 r psi Ø6 CV Ø6 CV Connector IN 365- ISO6952 rotection degree I65 mient temperture -2 + C Nominl power 8 W ON-OFF electro pneumtic control. Voltge 28Vdc - ilot pressure 5-1 r psi Ø6 CV Ø6 CV Connector IN 365- ISO6952 rotection degree I65 mient temperture -2 + C Nominl power 8 W (3) Vlid only for the section following the first one 22 IE/CV-MONOLOCK/3-216

21 Working sections ositioning / Control side escription rwing Micro-switch in nd rotection degree: I67 Nominl power:.1 1 / 25VC Minimum power: 1 m / VC Operting temperture: C Micro-switch in rotection degree: I67 Nominl power:.1 1 / 25VC Minimum power: 1 m / VC Operting temperture: C Cle length: 5 cm [19.69 inch] CV CV MONOLOCK Cle length: 5 cm [19.69 inch] Micro-switch in rotection degree: I67 Nominl power:.1 1 / 25VC Minimum power: 1 m / VC Operting temperture: C CV Cle length: 5 cm [19.69 inch] etent with djustle utomtic hydrulic relese in nd 29 CV Spool stroke djustment in mm inch CV CV Flexile cle control M16x1.5 M6 CV CV = luminium version (only CV) Cle supplied on request. Lenght cle nd control, contct our commercil dept IE/CV-MONOLOCK/

22 Working sections Service port vlves (optionl field) CV/* IS * * (*) S V(*) W* Xn * F* Service port vlves optionl, is required specil monolock ody. Omit for stndrd version (without vlves, without prerrnged for vlve) V Service port vlves escription rwing MONOLOCK V1 (*) Overlod vlve in position IS V S S S V IS V2 (3) nti-cvittion vlve in S S S V IS V rerrnged for usiliry vlve in with plug S S S Specify the relief vlve setting (from 2 to 35 r). uring the order it is suggested to specify the flow rte. For service port vlves or prerrnged for port vlve with plug in nd/or port plese contct our commercil deprtment. (3) Only for CV2 CV/* IS * * (*) S V W* Xn * F* Hndle lever (optionl field) Working section repeted for n. times (optionl filed) W* Hndle lever escription rwing W1 Stndrd CV 2 For cloche control use W2 M8 215 W2 Stndrd CV M IE/CV-MONOLOCK/3-216

23 Outlet sections Outlet CV/* IS * * (*) S V W* Xn * F* * Outlet op outlet Side outlet MONOLOCK S IS L IS S S S S S S HCO nd top outlet HCO nd side outlet HCO HCO S2 IS S S S HCO L2 IS S S S HCO hreds CV/* IS * * (*) S V W* Xn * F* F* hreds escription CV2 ----HCO CV ----HCO F3 3/8 S F 1/2 S F31 9/16-18NF (SE 6) F32 3/ - 16NF (SE 8) F33 7/8-1NF (SE 1) hreds villes on request IE/CV-MONOLOCK/

24 V..S. REVINI S.r.l Vi Mtteotti, 7 6 Ozzno Emili (ologn) - Itly el Fx sles@vpsrevini.com Code OC66 - Rev. 3 revini Fluid ower S.p.. Vi Moscov, Reggio Emili - Itly el Fx uidpower.com info@revinifl uidpower.com