Direct Operated 2 Port Solenoid Valve For Water, Oil, Steam, Air

Transcription

1 CAT.ES0- A Direct Operated Port Solenoid Valve For Water, Oil, Steam, Air New Series VX// Reduction of power consumption ( specification) W. W W W. W 0. W Low power consumption type: 0. W (Held at V) New VX Series now on sale!

2 Solenoid valves for various fluids used in a wide variety of Improvement of corrosion resistance Special magnetic material adopted Enclosure: Equivalent to IP Flame resistance UL9V-0 conformed Flame resistant mold coil material Low noise construction Special construction enables to reduce the metal noise. ( specification) Improvement of maintenance performance Maintenance is performed easily due to the threaded assembly. Direct Operated Port Solenoid Valve For Water, Oil, Steam, Air Reduction of power consumption ( specification) VX: W. W VX: W W VX:. W 0. W Low power consumption type: 0. W (Held at V) With mounting threads on the bottom A dedicated bracket is available. Installation example Bracket For orifice s ø, ø, ø., and ø New Series VX// VX VX VX mmø mmø Orifice. mmø mmø mmø 0 mmø Port /, / /, / / /, / / Material Body Seal Brass Stainless steel NBR FKM EPDM PTFE VX VX VX mmø Orifice mmø. mmø mmø Port /, / /, / /, / Material Body Seal Brass Stainless steel NBR FKM EPDM PTFE Manifold Base material: Aluminum Base material: Brass Base material: Stainless steel VX VX VX mmø Orifice mmø. mmø mmø Port (Common SUP type) IN port OUT port / / / Body Aluminum Brass Stainless steel Material Base Aluminum Brass Stainless steel Seal NBR FKM EPDM PTFE Features

3 applications New VX Series variations Pilot Operated Port VXD// For Air, Water, Oil Pilot Operated Port for Zero Differential Pressure VXZ/ For Air, Vacuum, Water, Oil Direct Operated Port VX// For Air, Vacuum, Water, Steam, Oil Valve type Port N.C./N.O. / to A to 0 A Orifice mmø 0 to 0 Pilot Operated Port VXP// For Steam (Air, Water, Oil) Valve type N.C./N.O. Port / to Water Hammer Relief, Pilot Operated Port VXR// For Water, Oil Orifice mmø 0 to Valve type Port Orifice mmø N.C./N.O. / to /. to C.O. Pilot Operated Port for High Pressure VXH For Air, Water, Oil Valve type Port N.C./N.O. / to A to 0 A Orifice mmø 0 to 0 Port for Dust Collector (Solenoid type, Air Operated type) VXF/, VXFA/ For Air Valve type N.C./N.O. Port / to Orifice mmø 0 to 0 Air Operated / Port VXA/, VXA/ For Air, Vacuum, Water, Oil Valve type N.C. Port / to / Orifice mmø 0 The VX series has been renewed as the new VX series, with a new construction Valve type N.C. Port / to / Orifice mmø 0 to 0 VXA/ VXA/ Valve type N.C./N.O. C.O. Port / to / / to / Orifice mmø to 0. to Features

4 Solenoid Valves Flow Characteristics (How to indicate flow characteristics). Indication of flow characteristics Indication of the flow characteristics in specifications for equipment such as solenoid valve, etc. is depending on Table (). Table () Indication of Flow Characteristics Corresponding equipment Equipment for pneumatics Equipment for controlling process fluids Indication by international standard C, b Av Other indications S Cv Cv Standards conforming to ISO : 99 IS B 90: 000 IS B 90: 000 Equipment: IS B,,, 9, ANSI/(NFPA)T..: 990 IEC0--: 99 IS B 00: 99 Equipment: IS B,,. Equipment for pneumatics. Indication according to the international standards () Standards conforming to ISO : 99 : Pneumatic fluid powercomponents using compressible fluids Determination of flow-rate characteristics IS B 90: 000 : Pneumatic fluid powercomponents using compressible fluids How to test flow-rate characteristics () Definition of flow characteristics Flow rate characteristics are indicated as a result of a comparison between sonic conductance C and critical ratio b. Sonic conductance C : Values which divide the passing mass flow rate of an equipment in a choked flow condition by the product of the upstream absolute and the density in the standard condition. Critical ratio b : It is the ratio which will turn to the choke flow (downstream /upstream ) when it is smaller than this values. (critical ratio) Choked flow : It is the flow in which the upstream is higher than the downstream and where sonic speed in a certain part of an equipment is reached. Gaseous mass flow rate is in proportion to the upstream and not dependent on the downstream. (choked flow) Subsonic flow : Flow greater than the critical ratio Standard condition : Air in a temperature state of 0 C, absolute 0. MPa (= 00 kpa = bar), relative humidity %. It is stipulated by adding the abbreviation (ANR) after the unit depicting air volume. (standard reference atmosphere) Standard conforming to: ISO : 990 Pneumatic fluid powerstandard reference atmosphere, IS B 9: 000: Pneumatic fluid powerstandard reference atmosphere () Formula of flow rate It can be indicated by the practical unit as following. When P + 0. b, choked flow P Q = 00 x C (P + 0.) () + t When P + 0. > b, subsonic flow P + 0. P + 0. b P Q = 00 x C (P + 0.) () b + t Q : Air flow rate [dm /min (ANR)], dm (Cubic decimeter) of SI unit are also allowed to described by l (liter). dm = l. Front matter

5 C : Sonic conductance [dm /(s bar)] b : Critical ratio [] P : Upstream [MPa] P : Downstream [MPa] t : Temperature [ C] Note) Formula of subsonic flow is the elliptic analogous curve. Flow characteristics curve is indicated in the Graph () For details, please use SMC s Energy Saving Program. Example) Obtain the air flow rate for P = 0. [MPa], P = 0. [MPa], t = 0 [ C] when a solenoid valve is performed in C = [dm /(s bar)] and b = According to formula, the maximum flow rate = 00 x x ( ) x = 00 [dm /min (ANR)] Pressure ratio = = Based on the Graph (), it is going to be 0. if it is read by the ratio as 0. and the flow ratio to be b = 0.. Hence, flow rate = Max. flow x flow ratio = 00 x 0. = 0 [dm /min (ANR)] Flow rate ratio b = P Equipment C, b P Q Pressure ratio (P + 0.) / (P + 0.) Graph () Flow characteristics line () Test method By attaching a test equipment with the test circuit indicated in Fig. () while maintaining to a certain amount which does not let the upstream go down below 0. MPa, measure the maximum flow to be saturated in the first place. Next, measure this flow rate at 0%, 0%, 0%, 0% and the upstream and downstream. And then, obtain the sonic conductance C from this maximum flow rate. Besides that, substitute each data of others for the formula of subsonic flow in order to find b, then obtain the critical ratio b from that average. Pressure gauge or convertor Pressure control equipment ød d Thermometer d ød Differential gauge or differential converter ød Flow control valve Air supply Filter Shut off valve 0d 0d d 0d d Flow meter Pipe for measuring temperature Equipment for test Pipe for measuring in the upstream side Pipe for measuring in the downstream side Fig. () Test circuit based on ISO, IS B 90 Front matter

6 Solenoid Valves Flow Characteristics (How to indicate flow characteristics). Effective area S () Standards conforming to IS B 90: 000: Pneumatic fluid powercomponents using compressible fluids Determination of flow rate characteristics Equipment standards: IS B : port solenoid valve for pneumatics IS B : port solenoid valve for pneumatics IS B : port, port solenoid valve for pneumatics IS B 9: Silencer for pneumatics IS B : Fittings of flexible joint for pneumatics () Definition of flow characteristics Effective area S: is the cross-sectional area having an ideal throttle without friction deduced from the calculation of the changes inside an air tank or without reduced flow when discharging the compressed air in a choked flow, from an equipment attached to the air tank. This is the same concept representing the easy to run through as sonic conductance C (effective area). () Formula of flow rate When P , choked flow P + 0. Q = 0 x S 9 (P + 0.) () + t When P + 0. > 0., subsonic flow P Q = 0 x S (P + 0.) (P P) () + t Conversion with sonic conductance C: S =.0 x C () Q :Air flow rate[dm /min(anr)], dm (cubic decimeter) of SI unit is good to be described by l (liter), too. dm = l S : Effective area [mm ] P : Upstream [MPa] P : Downstream [MPa] t : Temperature [ C] Note) Formula for subsonic flow () is only applicable when the critical ratio b is the unknown equipment. In the formula by sonic conductance C (), it is the same formula when b = 0.. () Test method By attaching the equipment for testing with the test circuit shown in Fig. (), discharge air into the atmosphere until the inside the air tank goes down to 0. MPa (0. MPa) from an air tank filled with compressed air of a certain (0. MPa) which does not go down below 0. MPa. At this time, measure the discharging time and the residual inside the air tank which had been left until it turned to be the normal values, and then determine the effective area S by using the following formula. The volume of air tank should be selected within the specified range by corresponding to the effective area of the equipment being tested. In the case of IS B,,, 9,, the values are in parentheses and the coefficient of formula is.9. V Ps S =. log0 () () t P + 0. T S : Effective area [mm ] V : Air tank capacity [dm ] t : Discharging time [s] Ps : Pressure inside air tank before discharging [MPa] P : Residual inside air tank after discharging [MPa] T : Temperature inside air tank before discharging [K] Pressure control equipment Thermometer Air supply Filter Shut off valve Pressure switch Control circuit Pressure gauge or convertor Timer (Clock) Pressure recorder Solenoid valve Power supply Equipment for test Rectifier tube in the upstream side Fig. () Test circuit based on IS B 90 Rectifier tube in the downstream side Front matter

7 . Flow coefficient Cv factor The United States Standard ANSI/(NFPA)T..:990: Pneumatic fluid powerflow rating test procedure and reporting method for fixed orifice components defines the Cv factor of flow coefficient by the following formula which is based on the test conducted by the test circuit analogous to ISO. Q Cv = () P (P + Pa). T P : Pressure drop between the static tapping ports [bar] P : Pressure of the upstream tapping port [bar gauge] P : Pressure of the downstream tapping port [bar gauge]:p = P P Q : Flow rate [dm /s standard condition] Pa : Atmospheric [bar absolute] T : Test conditions of the upstream absolute temperature [K] is < P + Pa =. ± 0. bar absolute, T = 9 ± K, 0.0 bar P 0. bar. This is the same concept as effective area A which ISO stipulates as being applicable only when the drop is smaller than the upstream and the compression of air does not become a problem.. Equipment for process fluids () Standards conforming to IEC0--: 99: Industrial process control valves. Part : Flow capacity, Section Three-Test procedures IS B 00: 99: Test method for the flow coefficient of a valve Equipment standards: IS B : Regulator for water IS B : Solenoid valve for steam IS B : Solenoid valve for fuel oil () Definition of flow characteristics Av factor: Value of the clean water flow rate represented by m /s which runs through a valve (equipment for test) when the difference is Pa. It is calculated using the following formula. ρ Av = Q () P Av : Flow coefficient [m ] Q : Flow rate [m /s] P : Pressure difference [Pa] ρ : Density of fluid [kg/m ] () Formula of flow rate It is described by the known unit. Also, the flow characteristics line shown in the Graph (). In the case of liquid: P Q =.9 x 0 Av (9) G Q : Flow rate [l/min] Av : Flow coefficient [m ] P : Pressure difference [MPa] G : Relative density [water = ] In the case of saturated aqueous vapor: Q =. x 0 Av P(P + 0.) (0) Q : Flow rate [m /s] Av : Flow coefficient [m ] P : Pressure difference [Pa] P : Relative density [MPa]: P = P P P : Relative density [MPa] Front matter

8 Solenoid Valves Flow Characteristics (How to indicate flow characteristics) Conversion of flow coefficient: Av = x 0 Kv = x 0 Cv () Here, Kv factor: Value of the clean water flow rate represented by the m /h which runs through the valve at to 0 C, when the difference is bar. Cv factor (Reference values): It is the figures representing the flow rate of clean water by US gal/min which runs through the valve at 0 F, when the difference is lbf/in (psi). Values of pneumatic Kv are different from Cv because the testing method is different from each other. Saturated aqueous vapor flow rate Q0 [kg/h] (when Av = x 0 [m ]) Ex. P = 0.MPa P = 0.MPa P = 0.MPa Upstream P = 0.MPa P = MPa P = 0.MPa P = 0.MPa P = 0.MPa Ex Water flow rate Q0 [l /min] (When < when Av = x 0 [m ]) Pressure difference P [MPa] Graph () Flow characteristics line Example ) Obtain the difference when water [l/min] runs through the solenoid valve with an Av = x 0 [m ]. Since Q0 = / = 0. [ /min], according to the Graph (), if reading P when Q0 is 0., it will be 0.0 [MPa]. Example ) Obtain the flow rate of saturated aqueous vapor when P = 0. [MPa], P = 0.00 [MPa] with a solenoid valve with an Av =. x 0 [m ]. According to the Graph (), if reading Q0 when P is 0. and P is 0.00, it is 0. [kg/h]. Hence, the flow rate Q = 0. x. =.0 [kg/h]. Front matter

9 () Test method By attaching the equipment for testing with the test circuit shown in Fig. () and running water at to 0 C, measure the flow rate with a difference of 0.0 MPa. However, the difference needs to be set with a large enough difference so that the Reynolds number does not go below a range of x 0. By substituting the measurement results for formula () to figure out Av. Thermometer Test range Pressure tap Equipment for test Pressure tap Throttle valve in the upstream side Flow meter d d Throttle valve in the downstream side 0d 0d Fig. () Test circuit based on IEC0--, IS B 00 Front matter

10 Flow Characteristics Note) Use this graph as a guide. In the case of obtaining an accurate flow rate, refer to front matter pages to. For Air Downstream of valve (P) MPa VX VX VX VX VX VX VX Upstream of valve P.0 MPa ,000,00 00,000, , Flow rate Q l/min (ANR) 0.9 Subsonic Critical Sonic ø ø ø. ø ø ø0 ø0 How to read the graph The sonic range to generate a flow rate of 00 l/min (ANR) is P 0. MPa for a ø orifice (VX ), and P 0. MPa for a ø. orifice (VX). For Saturated Steam Downstream of valve (P) MPa [] (9) [] () [] () [] (0) [0] () [] () [] () [] () [0] () [] (0) Upstream of valve P.0 MPa Subsonic Critical Sonic VX VX VX VX VX 0 VX VX Flow rate Q kg/h ø ø ø. ø ø ø0 ø0 Front matter Figures inside [ ] indicate the saturated steam holding heat (kcal/kg). Figures inside ( ) indicate the saturation temperature ( C). How to read the graph The sonic range to generate a flow rate of kg/h is P 0. MPa for ø. orifice (VXS), P 0. MPa for ø orifice (VXS), and P 0. MPa for ø orifice (VXS). The holding heat differs somewhat depending on the P, but at kg/h it is approximately 900 kcal/h.

11 Flow Characteristics Note) Use this graph as a guide. In the case of obtaining an accurate flow rate, refer to front matter pages to. For Water Flow rate Q l/min VX 0-0 ø0 0 0 VX 0- ø0 VX ø VX 0 ø VXø. VXø VXø (0.00) (0.00) 0.0 (0.0) 0.0 (0.0) Pressure differential P = (P P) MPa How to read the graph When a water flow of l/min is generated, lp 0.0 MPa for a valve with ø orifice (VX,, ). Front matter

12 Applicable Fluid Check List Direct Operated Port Solenoid Valve Series VX// All Options (Single Unit) Option symbol A B C D E G H K L M N P Q S V Note ) Note ) Note ) Fluid Name and Option Fluid (Application) Seal material NBR FKM EPDM PTFE FKM EPDM NBR FKM EPDM PTFE FKM FKM FKM EPDM PTFE PTFE FKM Note ) L, M, V options are for non-lube treatment. Note ) Contact SMC regarding manifold type. Ethyl alcohol Caustic soda (% ) Gas oil Silicon oil Steam system (Steam) (Max. C) Steam system (Condensation) (Max. 99 C) Medium vacuum (up to 0. Pa.abs) Parachloroethylene Helium Non-leak (0 Pa m /s) Heated water (Max. 99 C) Body, Shading coil material Brass/Copper Stainless steel/silver Brass/Copper Option symbol and body material Brass B A A S E V A V V E Stainless steel H H Q P M H M M P Note ) The leakage amount (0 Pa m /s) of V, M options are values when differential is 0. MPa. Note ) If using for other fluids, contact SMC. Coil insulation type B H B H B Note High corrosive spec., Oil-free Non-leak, Oil-free Steam (Max. C) Non-leak, Oil-free Front matter 9

13 Glossary of Terms Pressure Terminology. Maximum operating differential The maximum differential (the difference between the inlet and outlet ) which is allowed for operation, with the valve closed or open. When the downstream is 0 MPa, this becomes the maximum operating.. Minimum operating differential The minimum differential (differential between the inlet and the outlet ) required to keep the main valve fully opened.. Maximum system The maximum that can be applied inside the pipelines (line ). (The differential of the solenoid valve unit must be less than the maximum operating differential.). Proof The which must be withstood without a drop in performance after returning to the operating range. (value under the prescribed conditions) Others. Material NBR: Nitrile rubber FKM: Fluoro rubber Trade names: Viton, Dai-el, etc. EPDM: Ethylene propylene rubber PTFE: Polytetrafluoroethylene resin Trade names: Teflon, Polyflon, etc.. Oil-free treatment The degreasing and washing of wetted parts.. Passage symbol In the IS symbol ( ) IN and OUT are in a blocked condition ( ), but actually in the case of reverse (OUT>IN), there is a limit to the blocking. ( ) is used to indicate that blocking of reverse is not possible. Electrical Terminology. Apparent power (VA) Volt-ampere is the product of voltage (V) and current (A). Power dissipation (W): For, W = V/A cosθ. For, W = V/A. (Note) cosθ shows power factor. cosθ = 0.. Surge voltage A high voltage which is momentarily generated in the shut-off unit by shutting off the power.. Degree of protection A degree defined in the IS C 090: Waterproof test of electric machinery/appliance and the degree of protection against the intrusion of solid foreign objects. IP: Dusttight, Low jetproof type Low jetproof type means that no water intrudes inside an equipment that could hinder from operating normally by means of discharging water for minutes in the prescribed manner. Take appropriate protection measures, since a device is not usable in an environment where a water drop is splashed. Front matter 0

14 Direct Operated Port Solenoid Valve Series VX// For Water, Oil, Steam, Air Single Unit Solenoid Coil Coil: Class B, Class H Rated Voltage 00 V, 00 V, 0 V, 0 V, 0 V, 0 V, V, V, V Material Body Seal Electrical Entry Grommet Conduit DIN terminal Conduit terminal Valve Normally closed (N.C.) Normally open (N.O.) Brass, Stainless steel NBR, FKM, EPDM, PTFE VX VX VX mmø mmø. mmø mmø mmø 0 mmø Port,,, Orifice VX VX VX mmø mmø. mmø mmø Orifice Port,,, Manifold Valve Normally closed (N.C.) Normally open (N.O.) Base Common SUP type, Individual SUP type (Base material Aluminum only) Solenoid Coil Coil: Class B, Class H Material Body Base Seal Electrical Entry Grommet Conduit DIN terminal Conduit terminal Aluminum, Brass, Stainless steel Aluminum, Brass, Stainless steel NBR, FKM, EPDM, PTFE Manifold VX mmø mmø. mmø mmø Orifice (Common SUP type) Port IN port OUT port VX, VX Rated Voltage 00 V, 00 V, 0 V, 0 V, 0 V, 0 V, V, V, V

15 Direct Operated Port Solenoid Valve Series VX// For Water, Oil, Steam, Air Standard Specifications Valve specifications Coil specifications Valve construction Withstand Body material Seal material Enclosure Environment Allowable voltage fluctuation Allowable leakage voltage Coil insulation type Solenoid Coil Specifications MPa Electrical entry, Grommet with surge (GS) has a rating of IP0. Direct operated poppet.0 Brass, Stainless steel NBR, FKM, EPDM, PTFE Dusttight, Low jetproof (equivalent to IP) Location without corrosive or explosive gases 00 V, 00 V, 0 V, 0 V, 0 V, 0 V, V V, V ±0% of rated voltage ±0% or less of rated voltage ±% or less of rated voltage Class B, Class H Specification VX VX VX Specification Frequency (Hz) 0 VX 0 0 VX 0 0 VX 0 Power consumption (W). 0. Apparent power (VA) Inrush Holding Temperature rise (C ) Note) 0 Temperature rise (C ) Note) Note) The values are for an ambient temperature of 0 C and at the rated voltage. How to order solenoid coil assembly VX0 Series VX VX VX Note ) 00 V 0/0 Hz 00 V 0/0 Hz 0 V 0/0 Hz 0 V 0/0 Hz V V 0 V 0/0 Hz V 0/0 Hz 0 V 0/0 Hz N G Note ) Refer to the table () for the available combinations. G -Grommet GS- With grommet surge T -With conduit terminal TS - With conduit terminal and surge TL - With conduit terminal and light TZ - With conduit terminal, surge and light C- Conduit type H Valve/Material Symbol Coil insulation Note ) Class B Class H Valve N.C. N.O. DIN terminal or not available. Electrical entry D -DIN Connector DS - DIN with surge voltage suppressor DL - DIN with light DZ - DIN with surge suppressor and light DO- For DIN (without connector) DIN type is available with class B insulation only. Refer to the table () for the available combinations between each electrical option (S, L, Z) and rated voltage. Specification VX VX VX Specification Frequency (Hz) 0 VX 0 0 VX 0 0 VX 0 Power consumption (W). 0. Apparent power (VA) Inrush Holding 0 Temperature rise (C ) Note) 0 Temperature rise (C ) Note) Note) The values are for an ambient temperature of 0 C and at the of rated voltage. Name plate part no. AZ-T-VX Clip part no. (For N.C.) For VX: VX0N-0 For VX: VX0N-0 For VX: VX0N-0 Table () Rated Voltage Electrical Option Class B S L S / Voltage symbol Valve model Enter by referring to How to Order (Single Unit). Voltage 00 V 00 V 0 V 0 V 0 V V 0 V V V With surge voltage suppressor With light Z With light and surge voltage suppressor With surge voltage suppressor Clip Name plate Solenoid coil Class H L With light spec. is not available. Z With light and surge voltage suppressor

16 Series VX// For Water /Single Unit /Valve Specifications N.C. N.O. Passage symbol Passage symbol Port (A) (A) (0A) (A) Orifice (mmø) VX0-0 VX0-0. VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0. VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 0 VX0-0 VX0-0 VX0-0 VX0-0. VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 0 VX0-0 VX0-0 0 VX0-0 Max. operating differential (MPa) Flow characteristics Av x 0 - m Cv converted Max. system (MPa) Note) Weight (g) Note) Weight of grommet type. Add 0 g for conduit type, 0 g for DIN terminal type, and 0 g for conduit terminal type respectively. Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system. Port (A) (A) (0) Orifice (mmø)... VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 Max. operating differential (MPa) Flow characteristics Av x 0 - m Note) Weight of grommet type. Add 0 g for conduit type, 0 g for DIN terminal type, and 0 g for conduit terminal type respectively. Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system Cv converted Max. system (MPa) Note) Weight (g) Operating Fluid and Ambient Temperature Tightness of Valve (Leakage Rate) Power source Note) With no freezing Operating fluid temperature ( C) Solenoid valve option (symbol), G, L E, P to 0 to 99 to 0 Ambient temperature ( C) 0 to 0 0 to 0 Seal material NBR, FKM, EPDM Leakage rate (With water ) 0. cm /min or less

17 Direct Operated Port Solenoid Valve Series VX// For Water/Single Unit How to Order (Single Unit) Refer to the table () Solenoid valve option Refer to the table () Z Table () Port/Orifice Size Solenoid valve (Port ) Option symbol G E P L Suffix Oil-free specification 00 V 0/0 Hz 00 V 0/0 Hz 0 V 0/0 Hz 0 V 0/0 Hz V Seal material NBR EPDM FKM VX 0 VX Orifice Refer to the table () Port Refer to the table () Thread type T F N Select because the solenoid valve option L is the oil-free treatment. Body, Shading coil material Brass, Copper Stainless steel, Silver Brass, Copper Stainless steel, Silver Stainless steel, Silver Rc NPTF G NPT Refer to the table () Refer to page for ordering coil only. VX VX VX Port no. (Port ) Port no. (Port ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) Solenoid valve (Port ) Table () Solenoid Valve Option ( mmø) VX 0 ( ) VX VX 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) Dimensions page (Single unit) V 0 V 0/0 Hz V 0/0 Hz 0 V 0/0 Hz ( mmø) Orifice symbol (diameter) (. mmø) ( mmø) ( mmø) Coil insulation type B H B ( mmø) Note Orifice symbol (diameter) ( mmø) (. mmø) Heated water ( only) High corrosive, Oil-free (0 mmø) (mmø) 0 G 0 G G -Grommet GS- With grommet surge T -With conduit terminal TS - With conduit terminal and surge TL - With conduit terminal and light TZ - With conduit terminal, surge and light Table () Bracket Part No. Part no. VX 0 VX0N-A VX 0 VX 0 VX 0 VX 0 Bracket None B With bracket Refer to the table () if a bracket is ordered separately. Table () Rated Voltage Electrical Option Class B S L Z / Voltage With surge Voltage With With light and voltage surge voltage symbol suppressor light suppressor 00 V 00 V 0 V 0 V 0 V V 0 V V V / C- Conduit Electrical entry D -DIN Connector DS - DIN with surge voltage suppressor DL - DIN with light DZ - DIN with surge and light DO- For DIN (without connector) DIN type is available with class B insulation only. Refer to the table () for the available combinations between each electrical option (S, L, Z) and rated voltage. Class H S L Voltage With surge Voltage With voltage symbol suppressor light 00 V 00 V 0 V 0 V 0 V V 0 V V V spec. is not available. VX0N-A VX0N-A-L Z With light and surge voltage suppressor For Water For Steam For Oil For Air

18 Series VX// For Water /Manifold Solenoid Valve for Manifold/Valve Specifications N.C. N.O. Passage symbol Passage symbol Common SUP type Common SUP type Orifice (mmø). VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 Max. operating differential (MPa) Flow Max. system Max. operating Orifice Flow characteristics differential (MPa) characteristics Av x 0 - m Cv converted (MPa) (mmø) Av x 0 - m Cv converted. 0. VX-00 VX VX VX VX VX VX VX VX Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system. Max. system (MPa) Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system..0 Operating Fluid and Ambient Temperature Tightness of Valve (Leakage Rate) Power source Note) With no freezing Operating fluid temperature ( C) Solenoid valve option (symbol), G, L E, P to 0 to 99 to 0 Ambient temperature ( C) 0 to 0 0 to 0 Seal material NBR, FKM, EPDM Leakage rate (With water ) 0. cm /min or less

19 Refer to the table () Solenoid valve option Refer to the table ()-) How to Order Manifold Bases VVX VVX VVX Port (Out port) Suffix Z Oil-free specification Select because the solenoid valve option L is the oil-free treatment. Rc/ Rc/ All IN ports are Rc /. Manifold base Blanking plate part no. For VX: VVX-A For VX: VVX-A For VX: VVX-A How to Order Manifold Assemblies (Example) Enter the valve and blanking plate to be mounted under the manifold base part number. Example VVXC set VX-G... sets VVX-A... set VX G VX G C 0 Thread type Seal material F E NBR FKM EPDM Station n How to Order (Solenoid Valve for Manifold) T F N Rc NPTF G NPT Direct Operated Port Solenoid Valve Series VX// For Water/Manifold Orifice Refer to the table () 00 V 0/0 Hz 00 V 0/0 Hz 0 V 0/0 Hz 0 V 0/0 Hz V Number of manifolds 0 stations 0 stations 0 Refer to the table () Refer to page for ordering coil only. Suffix Z Oil-free specification Base, Seal material Refer to the table ()-(). is the symbol for mounting. Add an in front of the part numbers for solenoid valves, etc. to be mounted. V 0 V 0/0 Hz V 0/0 Hz 0 V 0/0 Hz Table () Port/Orifice Size Solenoid valve VX VX VX Electrical entry Table () Solenoid Valve Option Solenoid valve Base, Seal material option symbol () symbol () G E P L C S CE SE SF G -Grommet GS-With grommet surge Refer to the table () for the available combinations between each electrical option (S, L, Z) and rated voltage. Orifice symbol (diameter) ( mmø) ( mmø) (. mmø) Body, Base material Brass Stainless steel Brass Stainless steel Stainless steel Seal material NBR EPDM FKM ( mmø) Coil insulation type B Table () Rated Voltage Electrical Option Class B Class H S L Z S L / Voltage With surge With With light and With surge With Voltage voltage surge voltage voltage symbol suppressor light suppressor suppressor light 00 V 00 V 0 V 0 V 0 V V 0 V V spec. is not V available. C- Conduit D -DIN DS - DIN with surge T -With conduit terminal TS -With conduit terminal and DL - DIN with light surge DZ - DIN with surge TL - With conduit terminal and light and light TZ - With conduit DO- For DIN (without terminal, surge connector) and light DIN type is available with class B insulation only. H B Note Heated water ( only) High corrosive, Oil-free Z With light and surge voltage suppressor For Water For Steam For Oil For Air Enter the product s part number in order, counting the st station from the left in the manifold arrangement, when viewing the individual port in front. Dimensions page (manifold)

20 Series VX// For Oil /Single Unit /Valve Specifications N.C. N.O. Passage symbol Passage symbol Port (A) (A) (0A) (A) Orifice (mmø) VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 Max. operating differential (MPa) Flow characteristics Av x 0 - m Cv converted Max. system (MPa) Note) Weight (g) Note) Weight of grommet type. Add 0 g for conduit type, 0 g for DIN terminal type, and 0 g for conduit terminal type respectively. Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system. Port (A) (A) (0) Orifice (mmø)... VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 Max, operating differential (MPa) Flow characteristics Av x 0 - m Cv converted Max. system (MPa).0 Note) Weight (g) Note) Weight of grommet type. Add 0 g for conduit type, 0 g for DIN terminal type, and 0 g for conduit terminal type respectively. Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system. Operating Fluid and Ambient Temperature Tightness of Valve (Leakage Rate) Power source Operating fluid temperature ( C) Solenoid valve option (symbol) A, H D, N Note) to 0 Note) to 0 Note) to 0 Note) Dynamic viscosity: 0 mm /s or less Ambient temperature ( C) 0 to 0 0 to 0 Seal material FKM Leakage rate (With oil ) 0. cm /min or less

21 Direct Operated Port Solenoid Valve Series VX// For Oil/Single Unit Refer to the table () Solenoid valve option Refer to the table () Z Suffix Oil-free specification Orifice Refer to the table () Port Refer to the table () Thread type T F N VX 0 0 G VX 0 G Rc NPTF G NPT G -Grommet GS- With grommet surge C- Conduit Bracket None B With bracket Refer to the table () if a bracket is ordered separately. Electrical entry For Water For Steam For Oil Option symbol A H D N 00 V 0/0 Hz 00 V 0/0 Hz 0 V 0/0 Hz 0 V 0/0 Hz V Refer to the table () Table () Port/Orifice Size Refer to page for ordering coil only. Solenoid valve (Port ) VX VX VX Port no. (Port ) Port no. (Port ) 0 ( ) 0 ( ) Table () Solenoid Valve Option Seal material FKM 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) Solenoid valve (Port ) ( mmø) VX 0 ( ) VX VX 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) Body, Shading coil material Brass, Copper Stainless steel, Silver Brass, Copper Stainless steel, Silver V 0 V 0/0 Hz V 0/0 Hz 0 V 0/0 Hz ( mmø) Coil insulation type The additives contained in oil are different depending on the type and manufacturers, so the durability of the seal materials will vary. For details, please consult with SMC. Dimensions page (Single unit) Orifice symbol (diameter) (. mmø) ( mmø) ( mmø) B H ( mmø) Orifice symbol (diameter) ( mmø) (. mmø) T -With conduit terminal TS - With conduit terminal and surge TL - With conduit terminal and light TZ - With conduit terminal, surge and light D -DIN Connector DS - DIN with surge voltage suppressor DL - DIN with light DZ - DIN with surge and light DO- For DIN (without connector) DIN type is available with class B insulation only. Refer to the table () for the available combinations between each electrical option (S, L, Z) and rated voltage. (0 mmø) ( mmø) Table () Rated Voltage Electrical Option Class B S L Z / Voltage With surge Voltage With With light and voltage surge voltage symbol suppressor light suppressor 00 V 00 V 0 V 0 V 0 V V 0 V V V / Table () Bracket Part No. Part no. VX 0 VX0N-A VX 0 VX 0 VX 0 VX 0 Class H S L Voltage With surge Voltage With voltage symbol suppressor light 00 V 00 V 0 V 0 V 0 V V 0 V V V spec. is not available. VX0N-A VX0N-A-L Z With light and surge voltage suppressor For Air

22 Series VX// For Oil /Manifold Solenoid Valve for Manifold/Valve Specifications N.C. N.O. Passage symbol Passage symbol Common SUP type Common SUP type Orifice (mmø). VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 Max. operating differential (MPa) Flow Max. system Max. operating Orifice Flow characteristics differential (MPa) characteristics Av x 0 - m Cv converted (MPa) (mmø) Av x 0 - m Cv converted. 0. VX-00 VX VX VX VX VX VX VX VX Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system. Max. system (MPa) Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system..0 Operating Fluid and Ambient Temperature Tightness of Valve (Leakage Rate) Power source Operating fluid temperature ( C) Solenoid valve option (symbol) A, H D, N Note) to 0 Note) to 0 Note) to 0 Note) Dynamic viscosity: 0 mm /s or less Ambient temperature ( C) 0 to 0 0 to 0 Seal material FKM Leakage rate (With oil ) 0. cm /min or less 9

23 Direct Operated Port Solenoid Valve Series VX// For Oil/Manifold How to Order (Solenoid Valve for Manifold) Refer to the table () Solenoid valve option Refer to the table ()-) Z Suffix Oil-free specification VX VX Orifice Refer to the table () 00 V 0/0 Hz 00 V 0/0 Hz 0 V 0/0 Hz 0 V 0/0 Hz V Refer to the table () Refer to page for ordering coil only. V 0 V 0/0 Hz V 0/0 Hz 0 V 0/0 Hz G G Electrical entry G -Grommet C- Conduit GS-With grommet surge D -DIN DS - DIN with surge T -With conduit terminal TS -With conduit terminal and DL - DIN with light surge DZ - DIN with surge TL - With conduit terminal and light and light TZ - With conduit DO- For DIN (without terminal, surge connector) and light DIN type is available with class B insulation only. Refer to the table () for the available combinations between each electrical option (S, L, Z) and rated voltage. For Water For Steam For Oil For Air How to Order Manifold Bases VVX VVX VVX Port (Out port) Rc/ Rc/ All IN ports are Rc /. Manifold base Blanking plate part no. For VX: VVX-A-F For VX: VVX-A-F For VX: VVX-A-F How to Order Manifold Assemblies (Example) Enter the valve and blanking plate to be mounted under the manifold base part number. Example VVXCF set VXA-G... sets VVX-A-F... set Thread type T F N CF 0 Rc NPTF G NPT Seal material: FKM Station n Number of manifolds 0 stations 0 stations 0 Suffix Z Oil-free specification Base, Seal material Refer to the table ()-(). is the symbol for mounting. Add an in front of the part numbers for solenoid valves, etc. to be mounted. Enter the product s part number in order, counting the st station from the left in the manifold arrangement, when viewing the individual port in front. Table () Port/Orifice Size Solenoid valve VX VX VX Table () Solenoid Valve Option Solenoid valve option symbol () A H D N Orifice symbol (diameter) ( mmø) ( mmø) (. mmø) Base, Seal Body, Base material symbol () material CF SF CF SF Brass Stainless steel Brass Stainless steel Seal material FKM ( mmø) Table () Rated Voltage Electrical Entry Electrical Option Class B Class H S L Z S L Z / Voltage With surge With With light and With surge With With light and Voltage voltage surge voltage voltage surge voltage symbol suppressor light suppressor suppressor light suppressor 00 V 00 V 0 V 0 V 0 V V 0 V V spec. is not V available. B H only The additives contained in oil are different depending on the type and manufacturers, so the durability of the seal materials will vary. For details, please consult with SMC. Coil insulation type Note Dimensions page (manifold) 0

24 Series VX// For Steam /Single Unit /Valve Specifications N.C. N.O. Passage symbol Passage symbol Port (A) (A) (0A) (A) Orifice (mmø) VX0-0 VX0-0. VX0-0 VX0-0 VX0-0 VX0-0. VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 0 VX0-0 VX0-0 VX0-0. VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 0 VX0-0 VX0-0 0 VX0-0 Max. operating differential (MPa) Flow characteristics Av x 0 - m Cv converted Max. system (MPa) Note) Weight (g) Note) Weight of grommet type. Add 0 g for conduit terminal type. Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system. Port (A) (A) (0) Orifice (mmø)... VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 Max, operating differential (MPa) Flow characteristics Av x 0 - m Cv converted Max. system (MPa).0 Note) Weight (g) Note) Weight of grommet type. Add 0 g for conduit terminal type. Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system. Operating Fluid and Ambient Temperature Tightness of Valve (Leakage Rate) Power source Operating fluid temperature ( C) Solenoid valve option (symbol) S, Q Ambient temperature ( C) 0 to 0 Seal material PTFE Leakage rate (With air ) 00 cm /min or less

25 Direct Operated Port Solenoid Valve Series VX// For Steam/Single Unit How to Order (Single Unit) Refer to the table () Solenoid valve option Refer to the table () Z Suffix Oil-free specification 00 V 0/0 Hz 00 V 0/0 Hz 0 V 0/0 Hz 0 V 0/0 Hz Orifice Refer to the table () Port Refer to the table () Thread type T F N Rc NPTF G NPT Refer to the table () Refer to page for ordering coil only. VX 0 0 VX 0 0 V 0/0 Hz V 0/0 Hz 0 V 0/0 Hz G -Grommet GS- With grommet surge T -With conduit terminal TS - With conduit terminal and surge TL - With conduit terminal and light TZ - With conduit terminal, surge and light G G C- Conduit Bracket None B With bracket Refer to the table () if a bracket is ordered separately. Electrical entry For Water For Steam For Oil For Air Table () Port/Orifice Size Solenoid valve (Port ) VX VX VX Port no. (Port ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) Solenoid valve (Port ) VX VX Port no. (Port ) Table () Solenoid Valve Option Option Seal material symbol S PTFE Q Solenoid coil:, Class H only ( mmø) VX 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) Body material Brass Stainless steel ( mmø) Orifice symbol (diameter) (. mmø) ( mmø) ( mmø) Coil insulation type H ( mmø) Orifice symbol (diameter) ( mmø) (. mmø) Refer to the table () for the available combinations between each electrical option (S, L, Z) and rated voltage. (0 mmø) ( mmø) Table () Rated Voltage Electrical Option Class H S L Z / Voltage With surge Voltage With With light and voltage surge voltage symbol suppressor light suppressor Table () Bracket Part No. Part no. VX 0 VX0N-A VX 0 VX VX0N-A 0 VX 0 VX 0 00 V 00 V 0 V 0 V 0 V V 0 V V V spec. is not available. VX0N-A-L Dimensions page (Single unit)

26 Series VX// For Steam /Manifold Solenoid Valve for Manifold/Valve Specifications N.C. N.O. Passage symbol Passage symbol Common SUP type Common SUP type Orifice (mmø). VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 Max. operating differential (MPa) Flow characteristics Av x 0 - m Cv converted (mmø) Av x 0 - m Cv converted Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system. 0.. Max. system (MPa).0 Orifice. VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 Max. operating differential (MPa) Flow characteristics Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system Max. system (MPa).0 Operating Fluid and Ambient Temperature Tightness of Valve (Leakage Rate) Power source Operating fluid temperature ( C) Solenoid valve option (symbol) S, Q Ambient temperature ( C) 0 to 0 Seal material PTFE Leakage rate (With air ) 00 cm /min or less

27 Direct Operated Port Solenoid Valve Series VX// For Steam/Manifold How to Order (Solenoid Valve for Manifold) Refer to the table () Solenoid valve option Refer to the table ()-() Z Suffix Oil-free specification VX G VX G Orifice Refer to the table () 00 V 0/0 Hz 00 V 0/0 Hz 0 V 0/0 Hz 0 V 0/0 Hz Refer to the table () Refer to page for ordering coil only. 0 V 0/0 Hz V 0/0 Hz 0 V 0/0 Hz Electrical entry G -Grommet C- Conduit GS-With grommet surge T -With conduit terminal TS - With conduit terminal and surge TL - With conduit terminal and light TZ - With conduit terminal, surge voltage suppressor and light Refer to the table () for the available combinations between each electrical option (S, L, Z) and rated voltage. For Water For Steam For Oil For Air How to Order Manifold Bases VVX VVX VVX Port (Out port) Rc/ Rc/ All IN ports are Rc /. Manifold base Blanking plate part no. For VX: VVX-A-P For VX: VVX-A-P For VX: VVX-A-P Suffix How to Order Manifold Assemblies (Example) Z Oil-free specification Enter the valve and blanking plate to be mounted under the manifold base part number. Example VVXCP set VXS-G... sets VVX-A-P... set CP 0 Thread type T F N Rc NPTF G NPT Seal material: PTFE Number of manifolds 0 stations 0 stations 0 Base, Seal material Refer to the table ()-(). is the symbol for mounting. Add an in front of the part numbers for solenoid valves, etc. to be mounted. Table () Port/Orifice Size Solenoid valve VX VX VX Table () Solenoid Valve Option Solenoid valve option symbol () S Q Orifice symbol (diameter) ( mmø) ( mmø) (. mmø) Base, Seal material symbol () CP SP Body, Base material Brass Stainless steel Station n Dimensions page (manifold) ( mmø) Seal material PTFE Table () Rated Voltage Electrical Option Class H S L Z / Voltage With surge Voltage With With light and voltage surge voltage symbol suppressor light suppressor 00 V 00 V 0 V 0 V 0 V V 0 V V spec. is not V available. Coil insulation type H Enter the product s part number in order, counting the st station from the left in the manifold arrangement, when viewing the individual port in front.

28 Series VX// For Air /Single Unit (Inert gas, Non-leak, Medium vacuum) /Valve Specifications N.C. When the fluid is air. Please select the VCA series when using air because it is specifically designed for it. (The VCA series is limited to air to improve its function and service life.) N.O. Passage symbol Passage symbol Max. operating Orifice Flow Port differential (MPa) characteristics (mmø) C[dm /(s bar)] b Cv (A) (A) (0A) (A) VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX0-0 VX Note) Weight of grommet type. Add 0 g for conduit type, 0 g for DIN terminal type, 0 g for conduit terminal type respectively. Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system..... Max. system (MPa) Note) Weight (g) Port (A) (A) (0) Orifice (mmø)... VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 VX-0 Max. operating differential (MPa) C[dm /(s bar)] Flow characteristics b Note) Weight of grommet type. Add 0 g for conduit type, 0 g for DIN terminal type, 0 g for conduit terminal type respectively. Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system Cv Max. system (MPa) Note) Weight (g) Operating Fluid and Ambient Temperature Tightness of Valve (Leakage Rate) Power source Operating fluid temperature ( C) Solenoid valve option (symbol), G V, M 0 Note) to 0 0 Note) to 0 0 Note) to 0 0 Note) to 0 Note) Dew point temperature: 0 C or less Ambient temperature ( C) 0 to 0 0 to 0 Leakage rate Seal material Note) Non-leak, Air Medium vacuum NBR, FKM cm /min or less 0 Pa m /sec or less Note) Value on option V, M (non-leak, medium vacuum)

29 Direct Operated Port Solenoid Valve Series VX// For Air/Single Unit How to Order (Single Unit) Refer to the table () Solenoid valve option Refer to the table () Z Suffix Oil-free specification 00 V 0/0 Hz 00 V 0/0 Hz 0 V 0/0 Hz 0 V 0/0 Hz V Orifice Refer to the table () Port Refer to the table () Thread type T F N Select because the solenoid valve options V, M are the oil-free treatment. Option symbol G V M Rc NPTF G NPT Refer to the table () Table () Port/Orifice Size Refer to page for ordering coil only. Solenoid valve (Port ) VX VX VX Port no. (Port ) Port no. (Port ) 0 ( ) 0 ( ) Table () Solenoid Valve Option NBR FKM 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) Solenoid valve (Port ) Brass Stainless steel Brass Stainless steel VX 0 0 VX 0 ( mmø) VX 0 ( ) VX VX 0 ( ) 0 ( ) 0 ( ) 0 ( ) 0 ( ) Seal material Body material V 0 V 0/0 Hz V 0/0 Hz 0 V 0/0 Hz ( mmø) Please select the VCA series when using air because it is specifically designed for it. (The VCA series is limited to air to improve its function and service life.) B Orifice symbol (diameter) (. mmø) ( mmø) ( mmø) Coil insulation type ( mmø) Orifice symbol (diameter) ( mmø) (. mmø) Note Non-leak (0 Pam /sec), Oil-free, Medium vacuum (0. Pa.abs) G -Grommet GS- With grommet surge T -With conduit terminal TS - With conduit terminal and surge TL - With conduit terminal and light TZ - With conduit terminal, surge and light G G C- Conduit Bracket None B With bracket Refer to the table () if a bracket is ordered separately. Electrical entry D -DIN Connector DS - DIN with surge voltage suppressor DL - DIN with light DZ - DIN with surge and light DO- For DIN (without connector) DIN type is available with class B insulation only. Refer to the table () for the available combinations between each electrical option (S, L, Z) and rated voltage. Table () Rated Voltage Electrical Entry Electrical Option Class B (0 mmø) ( mmø) S Voltage With surge Voltage voltage symbol suppressor 00 V 00 V 0 V 0 V 0 V V 0 V V V / Table () Bracket Part No. Part no. VX 0 VX 0 VX 0 VX 0 VX 0 L With light VX0N-A VX0N-A VX0N-A-L Z With light and surge voltage suppressor For Water For Steam For Oil For Air Dimensions page (Single unit)

30 Series VX// For Air /Manifold (Inert gas, Non-leak, Medium vacuum) Solenoid Valve for Manifold/Valve Specifications N.C. N.O. Passage symbol Passage symbol Common SUP type Common SUP type Individual SUP type Individual SUP type Orifice (mmø). VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 Max. operating differential (MPa) Flow characteristics C[dm /(s bar)] b Cv Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system Max. system (MPa).0 Orifice (mmø). VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 VX-00 Max. operating differential (MPa) Flow characteristics C[dm /(s bar)] b Cv Refer to Glossary of Terms on front matter 0 for details on the max. operating differential and the max. system Max. system (MPa).0 Operating Fluid and Ambient Temperature Tightness of Valve (Leakage Rate) Power source Operating fluid temperature ( C) Solenoid valve option (symbol), G V, M 0 Note) to 0 0 Note) to 0 0 Note) to 0 0 Note) to 0 Note) Dew point temperature: 0 C or less Ambient temperature ( C) 0 to 0 0 to 0 Leakage rate Seal material Note) Non-leak, Air Medium vacuum NBR, FKM cm /min or less 0 Pa m /sec or less Note) Value on option V, M (non-leak, medium vacuum)

31 Refer to the table () Solenoid valve option Refer to the table () 00 V 0/0 Hz 00 V 0/0 Hz 0 V 0/0 Hz 0 V 0/0 Hz V VX 00 G VX 00 G Orifice Refer to the table () Refer to the table () How to Order Manifold Bases VVX VVX VVX Port (Out port) Rc/ Rc/ All IN ports are Rc /. Z Manifold base Blanking plate part no. For VX: X0-00 For VX/: VX0-00 Seal material V 0 V 0/0 Hz V 0/0 Hz 0 V 0/0 Hz How to Order Manifold Assemblies (Example) Enter the valve and blanking plate to be mounted under the manifold base part number. Example VVX set VX-00-G... sets VV set F Suffix Oil-free specification Select because the solenoid valve option V is the oil-free treatment. 0 Thread type T F N Rc NPTF G NPT Direct Operated Port Solenoid Valve Series VX// For Air/Manifold How to Order (Solenoid Valve for Manifold) Refer to page for ordering coil only. NBR FKM Station n Suffix Z Oil-free specification Base V Number of manifolds 0 stations 0 stations 0 Common SUP type Individual SUP type is the symbol for mounting. Add an in front of the part numbers for solenoid valves, etc. to be mounted. Enter the product s part number in order, counting the st station from the left in the manifold arrangement, when viewing the individual port in front. G -Grommet GS- With grommet surge T -With conduit terminal TS - With conduit terminal and surge TL - With conduit terminal and light TZ - With conduit terminal, surge voltage suppressor and light Table () Port/Orifice Size Solenoid valve VX VX VX Table () Solenoid Valve Option Option symbol V Orifice symbol (diameter) ( mmø) ( mmø) (. mmø) Body, Base material Aluminum Seal material NBR FKM Coil insulation type B ( mmø) Note Non-leak specification Please select the VCA series when using air because it is specifically designed for it. (The VCA series is limited to air to improve its function and service life.) Table () Rated Voltage Electrical Option Class B S L Z / Voltage With surge Voltage voltage With With light and surge voltage symbol suppressor light suppressor 00 V 00 V 0 V 0 V 0 V V 0 V V V Dimensions page (manifold) C- Conduit Electrical entry D -DIN DS - DIN with surge voltage suppressor DL - DIN with light DZ - DIN with surge and light DO- For DIN (without connector) DIN type is available with class B insulation only. Refer to the table () for the available combinations between each electrical option (S, L, Z) and rated voltage. For Water For Steam For Oil For Air