Manual. 30C and 45C Load Push and Load Push/Pull. cascad& Cascade is a Registered Trademark of Cascade Corporation

Transcription

1 b * Service Manua 30C and 45C Load Push and Load Push/Pu Seria Numbers through Manua Number R-2 cascad& Cascade is a Registered Trademark of Cascade Corporation

2 Contents Page Number INTRODUCTION. Section INSTALLATION INSTRUCTIONS, Section Load Push and Load Push/Pu (Non-Sideshifting) 3-2 Load Push and Load Push/Pu (Sideshifting) PERIODIC MAINTENANCE, Section TROUBLESHOOTING, Section Hosing Diagrams and Schematics Non-sideshifting begins Sideshifting without Soenoid begins Sideshifting with Soenoid begins Sideshifting with Adjustabe Patens begins Sideshifting with Sheet Retainer begins Sideshifting Patens begins Troubeshooting the Push/Pu Circuit Troubeshooting the Sideshift Circuit Troubeshooting the Adjustabe Paten Circuit Troubeshooting the Sheet Retainer Circuit Troubeshooting the Sideshifting Paten Circuit Troubeshooting the (Eectric) Hydrauic Facepate Stop Group SERVICE, Section Attachment Remova and Instaation Facepate and Pantograph Arms Disassemby Service and Reassemby Gripper Mechanism Disassemby Vave Remova and Instaation Disassemby and Inspection Cyinders Remova Genera Procedures Service Junction Bock Remova and Instaation Soenoid Vave Remova and Instaation Service Patens Remova and Instaation & 49 Inspection & 49 Manua/Eectric(Hydrauic) FacepateStopGroups Remova and Instaation. Adjustment.. Sheet Retainer Mechanism Remova and Instaation Form 5181 Rev. 1 i

3 Section 1 Introduction This service manua provides the instaation instructions, periodic maintenance requirements, troubeshooting procedures, service procedures, and standard abor times for Cascade s C-series oad push and oad push/pu. Truck System Requirements Truck Reief Vave Setting: 2000 psi, maximum. Voume: 30C: 3-5 GPM 45C: 5-7 GPM Recommended hose and fitting size: No. 6 (% inch, I.D.). Truck carriage must conform to the industria Truck Association (ITA) dimensiona standards as shown in the chart at the right. Make sure the truck carriage is cean and the notches are undamaged. In order to conform to industry standard practice, the hoses shoud be connected to the truck auxiiary vave as indicated by the chart at the right. Specia Instructions Definitions WARNING A statement preceded by A WARNING is information that shoud be acted upon to prevent bodiy injury. A WARNING is aways inside a rued box. CAUTION A statement preceded by CAUTION is information that shoud be acted upon to prevent machine damage. IMPORTANT A statement preceded by IMPORTANT is information that possesses specia significance. NOTE A statement preceded by NOTE is information that wi make your job easier. s -1 1 A Mounting Cass I I Cass III Dimension A (in.1 Min. Max Function, in Motion of the operator s hand sequence of Attachment when actuating the truck auxiocation to the Movement iary contro hande whie facing operator the oad. Adjust Sideshift Push/Pu Patens Sheet Retain Sideshift Patens Sideshift Right Rearward or Up Sideshift Left Forward or Down Pu (rearward) Rearward or Up Push (forward) Forward or Down Patens In Rearward or Up Patens Out Forward or Down Retain Rearward or Up Reease Forward or Down Sideshift Right] Rearward or Up Sideshift Left Forward or Down 3-1 Form 5181 Rev. 1

4 Section 2 Instaation Instructions 2.1 Load Push and Load Push/Pu (Non-Sideshifting) WARNING NOTE: Sideshiftina Load Push and Load Push/Pu Instaation begins with paragraph 2.2 A truck/attachment WARNING: Rated capacity of the combination is a responsibiity of the origina truck manufacturer and may be ess than shown on the attachment namepate. Consut the truck namepate Prior to Instaation 0 Connect a suitabe hoist chain (minimum ifting capacity: 1000 Ibs.) through the facepate to the frame and ift the attachment onto a baet. WARNING: Do not ift the attachment by the facepate. The facepate may and chains to ift Remove the the frame ower mounting hooks I QUICK DISCONNECT n I attachment or persona injury Remove the ower mounting hooks. IMPORTANT: On Quick Disconnect hooks, side the pin out from one hook and rotate to the position shown. Hoses 0 Insta Cascade Attachment Instaation Kit No. C OR Pumb No. 6 (minimum) hoses to the truck junction bock. CONNECT TO OJUNCTIO; BLOCK 1 L Function \ CAUTION: To prevent contamination of thesequence or check vave, fush the truck hoses by connecting them togetherand actuating the push/pu ever for 30 seconds in both directions to carry foreign matter to reservoir fiter. Junction Bock 0 Fush hoses To Truck Junction Bock Instaation (Non-Sideshifting) 0 Center the ift truck behind the attachment. 0 Insta the hoses to the sequence vave. Do not pinch, twrst, or otherwise damage the hoses. NOTE: Make certain the centering ug on the attachment engages a notch on the upper fork bar on the truck. Form 5181 Rev

5 Section 2 Instaation Instructions Instaation (Non-Sideshifting Cont.) 0 Raise the truck carriage into position on the attachment and tft the attachment 1 to 2 inches off the foor. 0 Insta the ower mounting hooks and tighten the capscrews to a torque of ft.-bs. NOTE: The hooks shoud contact the truck carriage ower crossbar. The ova hoes on the hook aow you to move them up or down to attain a maximum cearance shown. (Quick Disconnect Units: turn both hooks up and reinsta the pin.) Truck Carriage Lower Crossbar max Raise carriage into position, Lift attachment 1-2 inches off the paet. QUICK DISCONNECT Prior to Operation WARNING: Keep personne cear of unit when first extending facepate. Air insta ower mounting hook and tighten to a torque of ft..bs OLD DESIGN Turn the hooks up NEW DESIGN and insta the pin. Retighten the bots to a torque of 6070 ft.-bs. Remove air from the system by extending the facepate fuy, and keeping it there for seconds with the contro vave actuated. NOTE: This shoud correct an irreguary extending facepate. If it does not, retract the facepate and repeat the process a second time. Operate the unit through severa compete cyces and make sure a functions operate smoothy and correcty. PUSH/PULL UNITS: The gripper jaw shoud open prior to the facepate extension when the contro hande IS pushed forward The gripper jaw shoud cose competey prior to facepate retraction when the contro hande is pued back. 3-3 Form 5181 Rev. 2

6 . Section 2 Instaation Instructions 2.2 Load Push and Load Push/Pu (Sideshifting) Truck Preparation Skip Steps 1 through 4 if the unit is equipped with Quick Disconnect mounting hooks. TO ATTACH THE SIDESHIFT CYLINDER ANCHOR BRACKET: 0 Position the cardboard tempate*in the center notch of the truck Mark the two ines shown and remove the tempate. CAUTION: Correct anchor bracket positioning is crucia for proper sideshift cyinder operation. Pace tempate in center notch. *@ If the tempate is not avaiabe use the dimensions shown beow to ocate the bracket. 0 Position the cyinder anchor bracket on the marks and wed the bracket in pace using AWS E7018 rod. Preheat to % and wed the bottom and sides of the bracket with a 0.40 inch fiet wed. Mark both ines BRACKET LOCATION BRACKET LOCATION (A modes except Sheet Sav ) (Sheet Sav ) If tempate is ;ing, use these ensions to If temoate is racket Centerine of Use AWS E7018 rod. Preheat to F inch fiet weds, bottom and sides. Use AWS E7018 rod. Preheat to F inch fiet weds, bottom and sides. Form 5181 Rev. 2

7 Section 2 Instaation Instructions Truck Preparation (Cont.) Insta specia contro knob TO INSTALL THE CONTROL KNOB (Soenoid Units Ony): Remove the existing knob from the auxiiary vave contro hande and insta the specia knob as shown. If the contro hande is not threaded, wed on the specia adapter suppied with the specia knob. NOTE: It may be necessary to saw off a portion of the contro hande to achieve a comfortabe ength. CAUTION: Secure the cabe assemby to the contro hande so the cabe wi not be pinched at the truck cow when the hande is actuated.! threads Jam Nut (tighten to secure knob) Specia Adapter (discard if not Auxiiary Truck Vave Contro Insta contro knob pacard If the contro knob has 1 button, then the two-function side of the contro knob pacard shoud be showing. When the contro knob has 2 buttons then the three-function side of the pacard shoud be showing. Fit the dimpe on the pacard into the recess on the knob and insta the snap ring. When the contro knob has 3 buttons the three-function side of the pacard shoud be showing. Fit the dimpe on the pacard into the recess on the knob and insta the snap ring. ALL UNITS PERFORM THE Pace the sideshifting bearing segments in the notches of the truck carriage as shown. Appy a ibera coating of graphite base grease to the bearing segments. t-a-t-a-- 32-in. carriage: A=Qin. min.-16in. max. 36-in. carriage: A=14in. min.-17in. max. Locate a bearing segment on each side of the carriage srde pates as near as the [p notches permit To Truck Junction 0 To Truck Junction Bock% CAUTION: Fush the truck hoses by connecting them together and actuating the sideshift and push/pu ever for 30 seconds in both directions. 0 Fush hoses Instaation (Sideshifting) WARNING 0 Connect a suitabe hoist through the facepate to the frame and ift the attachment upright onto a paet. WARNING by the facepate. The facepate may attachment or persona injury may 0 Insta the two ower bearing strips on the attachment and coat them with a graphite base grease. 0 Remove the ower mounting hooks, (Quick Disconnect Units: pu out the retaining pin and rotate to the position shown.) and position the hooks as shown. Insta the bearing strips Form 5181 Rev. 1

8 Section 2 Instaation Instructions Instaation (Sideshifting Cont.) 0 Center the ift truck behind the attachment and raise the truck carriage into positron on the attachment. Lift the attachment 1 to 2 inches off the paet. f- I I Center the truck behind attachment and raise the carriage into position. II r Lift attachment 1-2 inches off the paet Lower Crossbar 0 insta the ower mounting hooks and tighten the capscrews to a torque of ft.-bs. NOTE: The hooks shoud not contact the truck carriage ower crossbar.the ova hoes on the hook aow you to move the hook up or down to attain a cearance between the minimum and maximum cearance shown. (Quick Disconnect Units: turn both hooks up and remsta the pin.) I QUICK DISCONNECT Insta ower mounting hook and OLD DESIGN Turn the hooks UP NEW DESIGN tighten to a and insta the pin. toraueof I Retighten the bots o ft.-b 1 a torque ft.-bs Remove cyinder rod end pins 0 Remove the push/pu cyinder rod end pins. Manuay pu the facepate away from the frame. 0 Insta the sideshift cyinder rod to the anchor bracket. Push the facepate back against the frame and reinsta the push/pu cyinder rod end pins. Insta sideshift cyinder rod to anchor bracket Form 5181 Rev

9 Section 2 Instaation Instructions Instaation (Sideshifting Cont.) TO INSTALL THE HOSES TO THE JUNCTION BLOCK: IMPORTANT: On soenoid operated attachments your junction bock may be mounted on the opposite side from the one shown. You can remove the tubes from the vave and reinsta them on the opposite side of the vave. You must aso reverse the hoses, fittings, eectric cabe and diodes iustrated in grey. grey can be reversed (moved to opposite side of vave) if junction bock is mounted on opposite side. 0 First push the attachment 4 inches (4 = ½ sideshift cyinder stroke) away from the junction bock. NOTE: Open both fittings on the sideshift cyinder to aow the rod to Remove the reusabe fittings from the attachment hoses and cut the hoses to ength as shown. (See the encosed instruction sheet on reusabe fittings.) Reinsta the fittings and attach the hoses to the junction bock. Position the hose guards to prevent the hoses from being scuffed by the frame. NOTE: If two junction bocks are used then repeat Steps 8, 9, and 10 for the other side. nd h 3-7 c J- Reinsta fittings and connect hoses to junction bock. Position hose guards to prevent scuffing of hoses during sideshifting. Form 5181 Rev. 1

10 Section 2 Instaation Instructions Instaation (Sideshifting The eectric cabe eading from the attachment shoud be tied to the hoses to prevent scuffing of the cabe during attachment sideshifting. See the eectric schematic to compete instaation of the cabe. 7.5 Amp r Wires eading from the diode Cabe Green (ground) k-- w Owner-supped Wiring TWO-FUNCTION (One-button contro knob) Compete instaation Of the cabe and contro knob. I -I I Wiring Compete instaation of the cabe and contro knob. THREE-FUNCTION (Two-button contro knob) \ V Doide Gre\en (ground) Retainer c \ 1 i Wemd : Vave I\ II [ I \ Prior to Operation Remove air from the system by extending the facepate fuy, and keeping it there for o-20 seconds with the truck vave actuated. NOTE: This shoud correct an irreguary extended facepate. If it does not, retract the facepate and repeat the process a second time. Aso sideshift the attachment severa times to force air from the sideshift cyinder to the truck reservoir. Operate the unit through severa compete cyces and make sure a functions operate smoothy and correcty. PUSH/PULL UNITS: The gripper jaw shoud open prior to the facepate extension when the contro hande is pushed forward The gripper jaw shoud cose competey prior to facepate retraction when the contro hande is pued back. 75Amp Owner supped Red Back \ \ Compete instaation of the cabe and contro knob MREE.FUNCTION (Twmbutton contro knob) sheet SW Form 5181 Rev

11 Section 3 Periodic Maintenance Hour Maintenance Every time the ift truck is serviced or every 100 hours of truck operation, whichever comes frrst, compete the foowing maintenance procedures. c] Inspect the paten shims at the bottom of the frame. Tighten the bots and readjust the shims as shown in paragraph 5.7-1, If necessary. 0 Inspect the facepate roers and reated parts for sufficient ubrication. If necessary, ubricate with Dubois FGG-2 food industry grease, Cascade part no. C Inspect the hoses mounted in the pantograph arms. They shoud be mounted securey and without hose droop. Check for hose wear and kinking at the primary and secondary arm connections. Repace kinked or worn hoses Hour Maintenance After each 500 hours of ift truck operation, in addition to the 100-hour maintenance procedures, perform the foowing procedures. q Inspect a bearings and shims at the pivot points for excessive wear. Repace if necessary. q Tighten the capscrews that secure the arm pivot pins to a torque of ft.-b. 0 Lubricate the facepate roers and guides with Dubois FGG-2 food industry grease, Cascade part no. C Inspect the bots securing the gripper pad. Tighten if necessary. IMPORTANT After competing any service procedure, aways test each function through 5 compete cyces. First test the attachment empty to beed excess air trapped in the system. Then test each function with a oad to make sure the attachment operates correcty before returning it to the job. 0 AWARNING: Tighten the paten hook capscrews to a torque of ft.-b. 0 Tighten the mounting hook capscrews to a torque of ft.-b Hour Maintenance After each 1000 hours of ift truck operations, in addition to the 100-hour and 500-hour maintenance procedures, perform the foowing procedure. jj Check the sideshift bearing strips and segments for excessive wear. Repace if necessary. Keep the bearing strips and segments we ubricated with Dubois FGG-2 food industry grease, Cascade part no. C On sheet retainer modes check the carrier assemby bearing segments for excessive wear. Repace if necessary. Keep the bearing strips and segments we ubricated with Dubois FGG-2 food industry grease. Cascade Part no. C Hour Maintenance After each 2000 hours of ift truck operation, in addition to the 100-hour, 500-hour, and 1000-hour maintenance procedures, perform the foowing procedure. q Repace a arm bushings and thrust washers. 3-9 Form 5181 Rev. 1

12 Section 4 Troubeshooting 4.1 Genera Procedures WARNING: Before servicing any hydrauic component, reieve pressure in the system. Extend the facepate 18 to 24 inches, turn the truck off, and open the truck auxiiary vaves severa times in both directions. After competing any service procedure, aways test the function through severa cyces. First test the attachment empty to beed air trapped in the system to the truck tank. Then test the attachment with a oad to be sure it operates correcty before returning it to the job. Stay cear of the oad whie testing. Do not raise the oad more than 3 inches off the foor whie testing Truck System Requirements Pressure: Your ift truck must suppy sufficient hydrauic pressure to hande the heaviest oad. PRESSURE MUST NOT EXCEED 2000 PSI. Voume: 30C: 3-5 GPM 45C: 5-7 GPM Toos Required In addition to a norma seection of hand toos and two engths of No. 6 hose, you wi need: A pressure gauge capabe of measuring presure to 2500 psi. (Cascade P/N ). A No. 6 swive nut run tee (37 JIC) suitabe for mounting the gauge. A meta pug (No. 6,37 JIC, mae) for pugging hose fittings. A neede shutoff vave, rated for 2500 psi service. (Recommended suppier for neede shutoff vaves: Marsh Instrument Co., Skokie. i.). Votmeter (or test ight) for soenoid equipped attach ments. Ohmmeter for soenoid equipped attachments. Assembe the hydrauic test instruments as shown. Neede \No. 6, 37O Fared Femae Fitting / NOTE: Make sure the arrow points in this direction. D&in Hose Form5181 Rev

13 Section 4 Troubeshooting Get A The Facts Before You Begin Working On The Attachment It is important that you gather a the facts regarding the probem before you begin service procedures. The best way is to tak with the operator. Ask for a compete description of the mafunction. The foowing guideines wi hep you decide where to begin your troubeshooting procedures. A. Push/Pu Circuit 0 Facepate wi not extend or retract. 0 Facepate extends and retracts uneveny. 0 Facepate operates sowy. 0 Gripper bar wi not ower or raise. Gripper bar is not sequenced with the push/pu function. 0 Gripper bar wi not hod the sip sheet when puing oad onto patens. If you encounter one of these probems, refer to paragraph 4.3 B. Sideshift Circuit 0 Attachment wi not sideshift. 0 Attachment sideshifts sowy. If you encounter one of these probems, refer to paragraph 4.4. C. Adjustabe Paten Circuit 0 Patens wi not move. Patens move very sowy. If you encounter one of these probems refer to paragraph 4.5. D. Sheet Retainer Circuit Sheet retainer bar wi not move. Sheet retainer wi not hod sip sheet when pushing oad off patens. Sheet Retainer bar moves sowy. If you encounterone of these probems refer to paragraph 4.6. E. Sideshifting Paten Circuit Paten wi not sideshift. Paten sideshifts sowy. If you encounter one of these probems refer to paragraph Form 5181 Rev. 1

14 . Section 4 Troubeshooting 4.2 Pumbing 4.2- Hosing Diagram- Load Push (Non-Sideshifting) FACEPLATE RETRACT PRESSURE - RETURN YZZZZZZ.... SLAVE - NOTE: For facepate EXTEND, reverse the coors shown. Truck Auxiiary Vave Circuit Schematic-Load Push (Non-Sideshifting) Reief Vave Truck Hydrauic Pump Form 5181 Rev

15 Section 4 Troubeshooting Hosing Diagram -Load Push/Pu (Non-Sideshifting) a.. 13 Gripper FACEPLATE RETRACT PRESSURE RETURN Z-...,,.:,.,... :,...::i: SLAVE NOTE: For facepate EXTEND, reverse the coors shown. Push/Pu Auxiiary Vave circuit Schematic-Load Push/Pu (Non-Sideshifting) Grtpper Cyinder Hydrauic Pump 3-13 Form 5181 Rev. 0

16 Section 4 Troubeshooting Hosing Diagram- Load Push (Sideshift without Soenoid) NOTE: Attachment has four junction bocks. SIDESHIFT RIGHT AND FACEPLATERETRACT PRESSURE - RETURN :,:::::::::::,::Lii::::-.::.::::(:::. SLAVE - NOTE: For GdeshiftLEFT and facepate EXTEND, reverse the coors shown. Hose Ree ATTACHMENT JUNCTION BLOCKS \ Sideshift. vave -. Vave ATTACHMENT JUNCTION BLOCKS Circuit Schematic Truck Vave Vave --d Hydrauic Pump Form 5181 Rev

17 Section Troubeshooting Hosing Diagram- Load Push (Sideshift without Soenoid) NOTE: Attachment has one junction bock. StDESHFT RIGHT AND FACEPLATERETRACT PRESSURE RETURN ---..i.iiii:, :..:._.:.: :,: _, a...i SLAVE - Truck Junction Bock ATTACHMENT. - JUNCTION BLOCK NOTE: For sideshift LEFT and facepate EXTEND, reverse the coors shown. Sequence Vave Push/Pu Cyinder Truck Junction Bock -Hose Ree Auxiiary Circuit Schematic-Load Push (Sideshift without Soenoid) Sideshift Auxiiary Truck Vave Push/Pu Auxiiary Truck Vave Truck Reief Vave A Truck Hydrauic Pump I 3-15 Form 5181 Rev. 0

18 Section 4 Troubeshooting Hosing Diagram -Load Push/Pu (Sideshift without Soenoid) NOTE: Attachment has four iunction bocks. > - Gr~ooer Push/Pu Cy I inder FACEPLATERETRACT PRESSURE RETURN SLAVE m ATTACHMENT JUNCTION BLOCKS rc: NOTE: For facepate EXTEND,,everse the coors shown. Sideshift Auxiiary Vave JC I Push/Pu Cyinder SIDESHIFT RIGHT PRESSURE RETURN *....>...../i.,..., ~...,.~~.:.:., ATTACHMENT JUNCTION BLOCKS NOTE: For sideshift LEFT reverse the coors shown. ush/pu yinder Hose Ree Sideshift Vave Form 5181 Rev

19 Section 4 Troubeshooting Hosing Diagram -Load Push/Pu (Sideshift without Soenoid) NOTE: Attachment has one junction b ock. n Gripper FACEPLATERETRACT ATTACHMENT JUNCTION BLOCK PRESSURE - RETURN u,.,.. :...:...:...:i.: :.::::.. SLAVE - NOTE: For facepate EXTEND, reverse the coors shown. Seque ce Vave -Push/Pu Cyinder Sideshift Auxiary Vave Truck Junction. Bock Vave SIDESHIFT RIGHT PRESSURE - RETURN ATTACHMENT JUNCTION BLOCK NOTE: For sideshift LEFT reverse the coors shown. Seqdence Vave Push/Pu Cvinder Vave 3-17 Form 5181 Rev. 0

20 Section 4 Troubes hooting e Circuit Schematic-Load Push/Pu (Sideshift without Soenoid) Gripper Cyinders Sideshift Auxiiary Vah NOTE: s ome attachments have one attachment junction bock and use truck unction bocks. Form 5181 Rev a

21 Section 4 Troubeshooting Hosing Diagram- Load Push (Sideshift with Soenoid) FACEPLATERETRACT PRESSURE RETURN SLAVE _.....,...._... :r.: ip81 Soenoid In EXT- Vave gj /Pu der NOTE: For facepate EXTEND, reverse the coors shown. Truck Auxiiary Vave SIDESHIFT RIGHT PRESSURE R ET U R N iiiii ii=iiii:i^i:i:=:::.:~ :==i In EXT NOTE: For sideshift LEFT, reverse the coors shown. Soenoid Vave ush/pu Minder Truck Auxiiary Vave 3-19 Form 5181 Rev. 0

22 Section Troubeshooting Circuit Schematic-Load Push (Sideshift with Soenoid) Push/Pu Sideshift Cyinder Sequence Vave I r II I Soenoid Vave Truck Hydrauic Pump Form 5181 Rev

23 Section 4 Troubeshooting Hosing Diagram- Load Push/Pu (Sideshift with Soenoid) FACEPLATE RETRACT PRESSURE RETURN 33=--=+..,,..:.: SLAVE - NOTE: For facepate EXTEND, revem the coors shown. Truck Auxiiary Vave SIDESHIFT RIGHT PRESSURE IO RETURN /m EXT NOTE: For sidashift LEFT reverse the coors shown. Soenoid Vave Ish/Pu imier Sideshift Cyinder fi\ Truck Auxiiary Vave 3-21 Form 5181 Rev. 0

24 Circuit Schematic-Load Push/Pu (Sideshift with Soenoid) Section 4 Troubeshooting Gripper Cyinders Sequence Vave Sideshift Cyinder 1 In EXT Soenoid Vave Truck Auxiiary Vave I I Truck Reief Vave w Truck Hydrauic Pomp Form 5181 Rev

25 Section 4 Troubeshooting Hosing Diagram-Load Push/Pu (Hydrauicay Adjustabe Patens) Push/Pu FACEPLATE RETRACT, and PLATENS POSJTIONED WIDE PRESSURE RETURN SLAVE./,,..::...,; :,,: NOTE: For facepate EXTEND, and patens positioned NARROW, reverse the coors shown. Cvinder p \ Truck Auxiiary Vave _ Grimer inders SIDESHIFT RIGHT PRESSURE RETURN..:.: i..: :.::,: ::::.:. ::: NOTE: For sideshift LEFT, reverse the coors shown. Sequence Vave iruck Junction Bock Truck Auxiiary Vave r eideshift Cyinder 3-23 Form 5181 Rev, 0

26 Section 4 Troubeshooting Circuit Schematic-Load Push/Pu (Hydrauicay Adjustabe Patens) Gripper Cyinders 37 ; 7-k -- r, ) I I Con,,O r.. Sideshift Cyinder In EXT r--+-f, Hose Ree Soenoid Paten Positioner Cyinder 1 r-1 I Truck Hydrauic Pump Form 5181 Rev

27 Section 4 Troubeshooting L Hosing Diagram-Load Push/Pu (Sheet Retainer-Sheet Sav ) Push/Pu Cyinder / Soenoid Vave FACEPLATE RETRACT PRESSURE RETURN.::?:::::::.:..:A....,... :i L = SLAVE - Sequence Vave In In Note: For facepate EXTEND, reverse the coors shown. In A EXT Sheet Retainer Sideshift Junction Rock Gripper Cyinder Truck Auxiiary Vave Soenoid / Vave SIDESHIFT RIGHT PRESSURE - RETURN iiiiiii.i:..i_::i:.:,:::,:,:,::::,: :. NOTE: For facepate EX reverse the coors shown. In In \ \\\\ Push/Pu Cyinder Sheet Retainer Junction Bock Gripper Cyinder Truck Auxiia Vave 3-25 Form 5181 Rev. 1

28 . Section 4 Troubeshooting Circuit Schematic-Load Push Pu (Sheet Retainer/Sheet Sav ) Sheet Retainer ( 1, In RET I-- Soenoid Vave Gripper Cyinders C Sideshift Cyinder I I c4, r.e I Sequence Vave In EXT Vave Truck Auxiiary Vave r-1 I Truck Reief Vave +i?@ Truck Hydrauvz Pump Form 5181 Rev

29 Section 4 Troubeshooting Hosing Diagram- Load Push/Pu (Sideshifting Patens) NOTE: Attachment has one junction bock. Grtpper FACEPLATE RETRACT ATTACHMENT JUNCTION BLOCK PRESSURE RETURN ::,... :. :.::,::.:. SLAVE NOTE: For facepate EXTEND, reverse the coors shown. SIDESHIFT PRESSURE RET R N RIGHT.?!!%Y:i i.j;j ::: 2.:/ ATTACHMENT JUNCTION BLOCK NOTE: For sideshift LEF reverse the coors shown Form 5181 Rev. 1

30 . Section 4 Troubeshooting Circuit Schematic-Load (Sideshifting Patens) Push/Pu Push/Pu Cy I I nders Gripper Cvnders C ^^ LL Sequence Vave Truck Reief Vave Truck Pump Hydrauic #NOTE. Some attachments have one attachment unction bock and use truck junction bocks. Form 5181 Rev

31 Section 4 Troubes hooting 4.3 Troubeshooting the Push/Pu Circuit There are six potentia probems that coud affect push/pu operation. InsuffIcient hydrauic pressure Externa eaks Defective soenoid (on soenoid-equipped attachments) Worn or defective cyinder seas Vave assemby mafunction Kinked suppy hoses Before proceeding with a test, determine whether the push function, pu function, or the gripper function is at faut. Then foow the check ist under the probem function (paragraph 4.3-1, 4.3-2, or 4.3-3) to isoate the probem area. In a cases, make sure the truck is deivering sufficient hydrauic pressure. A pressure drop of no more than 100 psi beow the truck reief vave setting at the auxiiary vave port is OK. If the pressure is not as specified, refer to the truck service manua for adjustment or service procedures. Pressure must not exceed 2000 psi Push Function Pressure Test 1. At the attachment vave assemby, disconnect the suppy hose that eads to the base end of the right-hand push/pu cyinder (as viewed from the driver s seat). Pug the cyinder suppy hose with a No. 6 meta pug. 2. Connect a pressure gauge with a neede shutoff vave and drain ine to the vave fitting (refer to paragraph for an iustration of the gauge arrangement). Put the drain ine in an empty container. 3. Open the neede vave no more than ½ to 1 fu turn. Start the truck and et it ide. 4. Operate the truck push ever for 4 to 5 seconds, then cose the neede vave tighty. Aow the gauge to reach and hod fu truck reief pressure for 2 or 3 seconds, then reease the push ever. Observe the pressure gauge and note the foowing: If the gauge does not reach the specific tiuck pressure (a 100 psi oss is OK), one of the foowing is responsibe. Interna Or Externa Leaks Refer to the accompanying diagram and check a areas that coud have externa eaks. Repair as required and operate the attachment to determine if the probem has been soved. Defective Push/Pu Soenoid (on attachments so equipped) Refer to paragraph 4.4-1, steps 3, 4 and 5 for soenoid tests. Shutte In The Vave Assemby Is Not Shifting Refer to Section 5.3 for vave inspection and servicing procedures. The Pioted Check Vave Or Reief Vave In The Vave Assemby Is Defective Refer to Section 5.3 for vave inspection and servicing procedures. If the gauge does reach truck pressure (a 100 psi oss is 0K);the foowing is responsibe for a mafunctioning push circuit. Gripper Cyinders Check Truck System Pressure Here PUSH FUNCTION Push/Pu Cyinders TEST Assemby Junction I I Bock 3-29 Form 5181 Rev. 0

32 Section 4 Troubeshooting a Push/Pu Cyinder Is Defective When the facepate extends uneveny with the right side out farther than the eft, suspect the eft-hand cyinder: vice versa for the right-hand cyinder. To further check the cyinders, insta a drain ine to the base end port and appy pressure to retract the cyinder. A steady oi stream after fu retraction indicates a bypass of oi at the seas or compensator vave. Refer to Section 5.4 for cyinder inspection and servicing procedures. Suspect Left Cyinder Pu Function Pressure Test 1. At the vave assemby, disconnect the suppy hose that eads to the rod end of the eft-hand push/pu cyinder (as viewed from the driver s seat). Pug the cyinder suppy hose with a No. 6 meta pug. 2. Connect a pressure gauge with a neede shutoff vave and drain ine to the vave fitting (refer to paragraph for an iustration of the gauge arrangement). Put the drain ine in an empty container. 3. Open the neede vave no more than /z to 1 fu turn. Start the truck and et it ide. 4. Operate the truck pu ever for 4 to 5 seconds, then cose the neede vave tighty. Aow the gauge to reach and hod fu truck reief pressure for 2 or 3 seconds, then reease the pu ever. Observe the pressure gauge and note the foowing: If the gauge does not reach the specific truck pressure (a 100 psi oss is OK), one of the foowing IS responsibe. Interna Or Externa Leaks Refer to the accompanying diagram and check a areas that coud have externa eaks. Repair as required and operate the attachment to determine if the probem has been soved. Defective Push/Pu Soenoid (on attachments so equipped) Refer to paragraph 4.4-1, steps 3, 4 and 5 for soenoid tests. Shutte in The Vave Assemby Is Not Shifting Refer to Section 5.3 for vave inspection and servicing procedures. The Pioted Check Vave Or Reief Vave In The Vave Assemby Is Defective Refer to Section 5.3 for vave inspection and servicing procedures. If the gauge does reach truck pressure (a 100 psi oss is OK), the foowing is responsibe for a mafunctioning pu circuit, Push/Pu Cyinder Is Defective When the facepate extends uneveny with the right side out farther than the eft, suspect the eft-hand cyinder; vice versa for the right-hand cyrnder. To further check the cyinders, insta a drain ine to the base end port and appy pressure to retract the cyinder. A steady oi stream after fu retraction indicates a bypass of oi at the seas or compensator vave. Refer to Section 5.4 for cyinder inspection and servicing procedures. I \ \ I / Right Side extends farther PULL FUNCTION TEST Suspect Left Cyinder / Right Side extends farther Form 5181 Rev

33 Section 4 Troubeshooting., Gripper Function If the gripper bar is not functioning propery, one of the foowing is responsibe. A pantograph WARNING: Disconnect Push/Pu cyinder rod and pins (see diagram 5.4-) from arm prior to testing to avoid possibe in advertant facepate retraction. The Gripper Bar Is Mechanicay Jammed Inspect for bent or broken hardware and repace where necessary. Kinked Suppy Hose Check the hoses from the vave to the cyinders for any kinks. Repace hoses if either is kinked. Worn Cyinders Seas Extend the facepate. Disconnect the hose at the eft hand push/pu cyinder rod end. Pug or cap the open ports and hoses. Insta a drain ine on the rod ends of the gripper cyinders and appy pressure to extend the cyinders. A steady stream of oi, after fu extension, indicates a bypass at the seas. Refer to Section 5.4 for cyinder inspection and servicing procedures. Pioted Check Vave In The Vave Assemby Is Defective Remove the gripper function tubing at the vave and repace with the pressure gauge and drain hose assemby. Appy pressure to extend the gripper cyinders. If the gauge does not regrster a pressure reading, remove and repace the gripper check vave. See paragraph for service procedures If the gauge registers a ow pressure reading, check for kinked hoses. gauge and drain Drain hose Ca Cascade s Service Department If you have carefuy and accuratey competed this check ist and you sti have not soved to probem, ca us. Our Service Department is open from 10:00 AM to 8:00 PM Eastern time. Ca (to free) In Oregon, (For ocations outside the U.S., contact your oca Cascade branch.) 3-31 Form 5181 Rev. 1

34 4 Troubeshooting Section. Q 4.4 Troubeshooting the 7.5 Amp Sideshift Circuit There are four potentia probem areas that coud affect sideshift operations. Insufficient truck hydrauic pressure Damaged sideshift bearing strips and segments Defective soenoid (on soenoid-equipped attachments) Worn or defective cyinders seas To isoate the probem area, compete the check ist in the foowing sequence Sideshift Troubeshooting Check List 1. To check for ow hydrauic pressure deivered by the truck hydrauic system to the attachment insta the pressure gauge in either ine eading to the sideshift cyinder. Operate the contro hande. A pressure drop of no more than 100 psi beow the truck reief vave setting at the auxiiary vave port is OK. If the pressure is not as specified, refer to the truck service manua for adjustment or service procedures. Pressure must not exceed 2000 psi. If the gauge does not register pressure or the push/pu circuit functions instead of the sideshift, perform the foowing tests: / \ 2. On soenoid-equipped attachments, check for oose connections in a eectrica wiring (from the contro button, to the truck s ignition switch, to the soenoid). 3. To test for votage at the soenoid disconnect the eectrica eads at the soenoid. Then, using a votmeter or a test ight, make sure there is votage at the eads when the sideshift button is depressed. Fuse 7.5 Amp ~~~~mn P If there is no votage to the soenoid, begin troubeshooting the eectrica circuit for shorts (be sure to incude the sideshift switch in the contro hande in 7.5 Amp your tests). If there is votage to the soenoid when the sideshift button is depressed, test for coi continuity To test for coi continuity, check the soenoid coi by pacing an ohmmeter test ead on each soenoid termina If there is current through the ohmmeter, but the soenoid does not cick when the sideshift button is depressed, the soenoid spoo is jammed and the soenoid vave shoud be repaced. If there is no current through the ohmmeter, the coi is defective and shoud be repaced. 5. Inspect the sideshift bearing strips and segments for excessive wear. Repace if necessary. Keep the bearing strips and segments we ubricated with Dubois FGG-2 food industry grease, Cascade part no. C The sideshift cyinder seas may be worn. Insta a drain ine in the base end of the cyinder and appy pressure to retract the cyinder. A steady stream of oi after fu retraction indicates a bypass at the seas. Refer to Section.514 for cyinder inspection and servicing procedures. Form 5181 Rev. 1 Wiring Remanning wires 1 are back / TWO-FUNCTION Onebutton contro knob} k- Green > (ground) 1*1, ma Contro Q m Soenoid Knob Red \ Owner-suppied Wiring THREE-FUNCTION (Two-button contro knob) (ground) Ca Cascade s Service Department If you have carefuy and accuratey competed this check ist and you sti have not soved the probem, ca us. Our Service Department is open from 10:00 AM to 8:00 PM Eastern time. Ca 80& (to free) In Oregon, I (For ocations outside the US., contact your oca Cascade branch.) 3-32

35 Section 4 Troubeshooting 4.5 Troubeshooting the Hydrauicay Adjustabe Paten Circuit There are three potentia probem areas that coud affect the adjustabe paten operations. Insufficient truck hydrauic pressure Defective soenoid Worn or defective cyinder seas To isoate the probem area, compete the check ist in the foowing sequence. 7.5 Amp Fuse Adjustabe Paten Troubeshooting Check List To check for ow hydrauic pressure deivered by the truck hydrauic system to the attachment insta the pressure gauge in either ine eading to the adjustabe paten cyinder. Operate the contro hande. A pressure drop of no more than 100 psi beow the truck reref vave setting at the auxiiary vave port is OK. If the pressure is not as specified, refer to the truck service manua for adjustment or service procedures. Pressure must not exceed 2000 psi. If the gauge does not register pressure or the push/pu circuit functions instead of the adjustabe patens, perform the foowing tests: 2. Check for oose connections in a eectrica wiring (from the contro button, to the truck s ignition switch, to the soenoid). 3. To test for votage at the soenoid disconnect the eectrica eads at the soenoid. Then, using a votmeter or a test ight, make sure there is votage at the eads when the adjustabe paten button is depressed. If there is no votage to the soenoid, begin troubeshooting the eectrica circuit for shorts (be sure to incude the adjustabe paten switch in the contro hande in your tests). If there is votage to the soenoid when the adjustabe paten button is depressed, test for coi continuity. 4. To test for coi continuity, check the soenoid coi by pacing an ohmmeter test ead on each soenoid termina. If there is current through the ohmmeter, but the soenoid does not cick when the adjustabe paten button is depressed, the soenoid spoo is jammed and the soenoid vave shoud be repaced. If there is no current through the ohmmeter, the coi is defective and shoud be repaced. 5. The adjustabe paten cyinder seas may be worn. Extend the facepate. Disconnect the hose at the eft hand push/pu cyinder rod end. Pug or cap the open ports and hoses. Insta a drain ine as shown in the iustration and appy pressure to extend the cyinder. A steady stream of oi after fu extension indicates a bypass at the seas. Refer to Section 5.4 for cyinder inspection and servicing procedures. Owner-suppied Wiring THREE-FUNCTION (Two-button contro knob) I VIEWED FROM FRONT OF ATTACHMENT Ca Cascade s Service Department If the probems isted in this Section do not correspond to the probem you have, or if the procedures outined here have not soved your probem, do not proceed. Ca a Cascade Service Representative at (to-free), or in Oregon ca Cascade s Service Department is open between 10:00 AM and 8:00 PM Eastern time. Ca (to free) In Oregon, (For ocations outside the U.S., contact your oca Cascade branch.) Form 5181 Rev. 1

36 Section 4 Troubeshooting 4.6 Troubeshooting the Sheet Retainer Circuit There are three potentia probem areas that coud affect the sheet retainer operations. 0 Insufficient truck hydrauic pressure 0 Defective soenoid 0 Worn or defective cyinder seas To isoate the probem area, compete the check ist in the foowing sequence Sheet Retainer Troubeshooting Check List 1. To check for ow hydrauic pressure deivered by the truck hydrauic system to the attachment, insta the pressure gauge in either ine eading to the sheet retainer cyinder. Operate the contro hande. Form 5181 Rev. 1 A pressure drop of no more than 100 psi beow the truck reief vave setting at the auxiiary vave port is OK. If the pressure is not as specified, refer to the truck service manua for adjustment or service procedures. Pressure must not exceed 2000 psi. If the gauge does not register pressure or the push/pu circuit functions instead of the sheet retainer, perform the foowing tests: Check for oose connections in a eectrica wiring (from the contro button, to the trucks ignition switch, to the soenoid). To test for votage at the soenoid disconnect the eectrica eads at the soenoid. Then, using a votmeter or a test ight, make sure there is votage at the eads when the sheet retainer button is depressed. If there is no votage to the soenoid, begin troubeshooting the eectrica circuit for shorts (be sure to incude the sheet retainer switch in the contro hande in yourtests). 0 If there is votage to thesoenoid when the sheet retainer button is depressed, test for coi continuity. To test for coi continuity, check the soenoid coi by pacing an ohmmeter test ead on each soenoid termina. 0 If there is current through the ohmmeter, but the soenoid does not cick when the sheet retainer button is depressed, the soenoid spoo is jammed and the soenoid vave shoud be repaced. 0 If there is no current through the ohmmeter, the coi is defective and shoud be repaced. The sheet retainer cyinder seas may be worn. Extend the facepate. Disconnect the hose at the eft hand push/pu cyinder rod end. Pug or cap the open ports and hoses. Insta a drain ine as shown in the iustration and appy pressure to extend the cyinder. A steady stream of oi afterfu extension indicates a bypass at the seas. Refer to Section 5.4 for cyinder inspection and servicing procedures. - _ d VIEWED FROM FRONT OF ATTACHMENT Compete instaation of the cabe and contro knob. Ca Cascade s Service Department z-green 7 Red If the probems isted in this Section do not correspond to the probem you have, or if the procedures outined here have not soved your probem, do not proceed. Ca a Cascade Service Representative at (to-free), or in Oregon ca Cascade s Service Department IS open between 10:00 AM and 8:00 PM Eastern time. Ca (toi free) In Oregon, (For ocations outside the U.S., contact your oca Cascade branch.) 3-34

37 Section Troubeshooting Troubeshooting the (Eectrica) Hydrauic Facepate Stop Groups There are four potentia areas that coud effect the eectrica facepate stop operations. Defective soenoid 7.5 Amp Fuse -L Defective imit switch a Improper tmit switch actuator adjustment A 1 T y+ rj,, + ] Back 0 Fauty eectrica connection Green (ground11 To isoate the probem area, compete the check ist in the White foowing sequence. Red Push/Pu 4) -, Sideshift Cabe Stop Group Troubeshooting Check List 1. Check for oose connections in a eectrica wiring from the contro button, to the trucks ignition switch, to the soenoid). 2. To test for votage at the soenoid disconnect the eectrica eads at the soenoid. Then, using a votmeter or a test ight, make sure there is votage at the eads when the stop button IS depressed. 0 If there is no votage to the soenoid, begin troubeshooting the eectrica circuit for shorts (be sure to incude the stop switch in the contro hande in your tests). If there is votage to the soenoid when the stop button is depressed, test for coi continuity. 3. To test for coi continuity. check the soenoid coi by pacing an ohmmeter test ead on each soenoid termina. If there is current through the ohmmeter, but the soenoid does not cick when the stop button is depressed, the soenoid spoo is jammed and the soenoid vave shoud be repaced. 0 If there is no current through the ohmmeter, the coi is defective and shoud be repaced. Contro Knob - Owner-&pied Wiring TWO-FUNCTION (Two-button contro knob) 3-35 Form 5181 Rev. 1

38 . Section 4 Troubeshooting Stop Group Troubeshooting Check List (Cont.) + 4. To test for votage at the imit switch disconnect the eads at the switch. Then using a votmeter or a test ight, make sure there is votage at the eads when the stop button on the contro knob is pressed. If there is no votage at the imit switch, begin troubeshooting the eectrica circuit for shorts (be sure to incude the stop switch in the contro hande in your tests). If there is votage to the imit switch when the stop button is depressed, test for coi continuity. 5. To test for imit switch continuity, check the switch by pacing an ohmmeter test ead on each imit switch ead If there is no current through the imit switch and the actuator wire is rotated to activate the switch, the imit switch is defective and shoud be repaced. 7.5 Amp Fuse Cabe Soenoid Owner-suppied Wfrinb? Limit Switch THREE-FUNCTION (Three-button contro knob).o Ca Cascade s Service Department If you have carefuy and accuratey competed this check ist and you sti have not soved to probem, ca us. Our Servrce Department is open from 10:00 AM to 8:00 PM Eastern time. Ca (to free) In Oregon, (For ocatrons outsrde the U.S., contact your oca Cascade branch.) Form 5181 Rev

39 Section 5 Service 5.1 Attachment Remova and Instaation Fuy extend the facepate. Lower the attachment onto a paet Remove the ower mounting hooks. For reassemby tighten the capscrews to a torque of ft.-bs. Quick Disconnect Hooks: Pu the pin as far as it wi go, rotate the hooks down and reinsta pin as shown. Disconnect, tag, and cap the attachment hoses at the truck junction bock(s). NOTE: Some units wi have truck hoses attached to junction bocks on the attachment. Disconnect and cap these. Disconnect the sideshift cyinder, if equipped, from the truck carriage anchor bracket. Disconnect the eectrica connection at the truck, on soenoid mounted attachments. Lower the truck carriage and back away from the attachment. Quick Disconnect Units: Tit the mast fuy forward before owering the carriage and backing away from the attachment. For reinstaation, reverse the above procedures, making sure tab in upper hook propery engages notch in upper truck carriage bar. Fuy Extend the Faceoate 6 Lower Attachment onto a Paet b Remove Mounting QUICK DISCONNECT UNITS n Lower Hooks Lower Carriage A II I Form 5181 Rev. 1

40 1 Section 5 Service 5.2 Facepate and Pantograph Arms 5.2- Disassemby 0 Remove the cotter pin and pin from the ink on the backside of the Remove the cotter pin and casteated nut that join the secondary arms together. Remove the pin. 0 Disconnect the four gripper hose ends from the tubing on the top primary arm. Disconnect the gripper hose ends from the gripper cyinder fittings. Cap the hose ends and tag for reassemby. 0 Attach a hoist chain to the facepate. 0 Remove the capscrews and pins which hod the secondary arms to the primary arms. 0 Twist each secondary arm towards the facepate center to remove them from the channes on the backside of the Attach a hoist to the frame assemby if the attachment was removed from the truck. 0 Remove the capscrews and pins from the rod end of the push/pu cyinders. 0 Remove the frame capscrews and pins that hod the pantograph arms to the frame. Attach a hoist chain if attachment was removed from truck nemove and Dins Attach hoist chain Top Primary Arm Tubing Remove capscrews and pins Remove cotter pin Secondary Arm.o Twist each arm toward center Remove cotter pin and pin from ink Form 5181 Rev

41 Section 5 Service Service and Reassemby 0 Inspect a shims, and washers and repace any that are scored or worn uneveny. 0 Inspect the Tefon bushings for wear. Repace the bushings if the coating is scored or worn through. 0 Reassemby is the reverse of the disassemby procedures. Appy grease to pins before reassemby. CAUTION: Shim the primary arms at the bottom to position each cevis as shown. Shim the top of the primary arms to provide,030 inch maximum cearance as shown. Shim the secondary arm at the bottom to provide,030 inch maximum cearance as shown. 0 After reassemby and instaation on the truck, extend and retract the facepate 5 times to beed excess air that may be trapped in the system. If the facepate extends at an ange after beeding excess air, and the cyinders are not defective (see paragraph 4.3- and 4.3-Z). use the foowing procedure to correct the misaignment. NOTE: If any major component (frame, facepate pantograph arm, etc.) has been repaced, use this procedure to correct the misaignment. a. Fuy extend the facepate with the eccentric pin at a neutra positron (the etter N shoud be next to the capscrew). b. Measure the distance between the facepate and the frame on both sides. The measurements shoud be equa within % inch. If the measurements differ by more than % inch the pin opposite the ongest measurement shoud be moved to the R (Retract) positron as foows. c. Remove the capscrew and eyebot. Insert a meta rod and sowy turn the pm around unti the R is near the capscrew. c. Insert the eyebot and tighten the capscrew to a torque of ft.-bs. e. If sti misaigned beyond % inch, turn pin opposite shortest measurement to E position, near the capscrew. Ghim primary arms 1 ci=-~= here IO provide L L measurement NEUTRAL FRONT OF ATTACHMENT CAM POSITION y Arm k II Shim sect Dndary arms at botrom to provide Gripper Mechanism Disassemby 0 Remove the cotter pins and pins retaining the gripper cyinder rods to the gripper bar. 0 Remove a the capscrews hoding the gripper jaw to facepate.the channe is now free. 0 Remove, tag, and pug the hoses at the gripper cyinders. 0 Remove the nut retaining the cyinderto the facepate and pu out the cyinder. 0 Reassemby is the reverse of disassemby. Remove cottwpin 3-39 Form 5181 Rev. 2

42 Section 5 Service a 5.3 Vave, Load Push and Load Push/Pu Remova Extend the facepate. Remove, tag and pug a tubing at the vave. 0 Remove the two capscrews and ockwashers retaining the vave and spacer (45C ony) to the attachment frame. Spacer (45C ony) Disassemby and Inspection 0 Remove both springs, spacers, and bas from the bore. Inspect the bas and ba seats for nicks or wear. Repace the vave body if the seat is deepy nicked or scored. Aways repace a Remove the hex head pugs at either end of the vave to remove the shutte. Remove the adaptor pugs and check cartridges. Repace the seas. 0 Remove the reief cartridge. Repace the Seas. 0 Cean the vave with sovent and inspect a bores for nicks or wear. Repace the vave body if any bore is deepy nicked or scored. Repace the shutte if deepy Remove adapter and nicked or scored. check cartridges and 0 Reassembe the bas, spacer and springs ast. Reseat repace seas, back-up the ba by sharpy tapping it into its seat with a brass iings and o-rings. punch prior to instaation of spacers and Seas and cartridges may vary from those shown. Remove both hex pugs to remove shutte Cean body with sovent and inspect for nicks or wear. See Instruction 6 for reassemby Remove a components and inspect bores for nicks or wear Form 5181 Rev. 2