30 Electric ding. IMPORTANT: Read and save these instructions. ALL RANGES CAN TIP INJURY TO PERSONS COULD RESULT SEE INSTALLATION INSTRUCTIONS

Transcription

1 Part No ALL RANGES CAN TIP INJURY TO PERSONS COULD RESULT INSTALL ANTI-TIP DEVICE PACKED WITH RANGE SEE INSTALLATION INSTRUCTIONS 30 Eectric ding IMPORTANT: Read and save these instructions. IMPORTANT: Instaer: Leave Instaation Instructions with the homeowner. Homeowner: Keep Instaation Instructions and anti-tip bracket tempate for future reference. Save Instaation Instructions for oca eectrica inspector s use.

2 Before you start... Read eectrica and carpentry instructions. Cabinet opening Proper instaation is your responsibiity. A auaified technician must insta this range. Make dimensions sure you have everything necessary for-correct instaation. It is the customer s responsibiity to make sure that the has been propery prepared and that the instaation cearances SDecified on the mode/seria ratina pate are met. The mode/seria rating pate is Iotated on the oven frame behind the door. Check ocation where range wi be instaed. The range shoud be ocated for convenient use in the kitchen. Recessed instaations must provide compete encosure of the sides and rear of range. ALL OPENINGS IN THE WALL OR FLOOR WHERE RANGE IS TO BE INSTALLED MUST BE SEALED. 16 upper cabinet to IMPORTANT: Some cabinet and buiding materias are not designed to withstand the heat produced by the oven for baking and sef-ceaning. Check with your buider or cabinet suppier to make sure that the materias used wi not discoor, deaminate or cearance from sustain other damage. both sides of It is the customer s responsibiity: wa or other To contact a quaified eectrica instaer. combustibe materia. To assure that the eectrica instaation is adequate and in conformance with Nationa Eectrica Code, I ANSVNFPA 70 - atest edition*, and a oca codes and ordinances. 25 depth 24 base cabinet depth 36 height opening width /,d receptace or junction box - 6 to 22 from either cabinet, d 7 max. from foor. y required between cutout and cabinet door or hinge. Product dimensions d;rp hande \ cooktop height Injury Hazard To eiminate the risk of burns or fire, avoid instaing cabinet storage above the cooking surface. If cabinets are aready instaed, reduce the hazard of reaching over a heated cooking surface by instaing a range hood. The range hood shoud extend a minimum of 5 inches out from the bottom front of the cabinets. Reaching over a heated cooking surface coud resut in a serious burn. Mobie home instaation The instaation of this range must conform to the Manufactured Home Construction and Safety Standards, Tite 24 CFR, Part 3280 (formery the Federa Standard for Mobie Home Construction and Safety, Tite 24, HUD, Part 280); or when such standard is not appicabe, the Standard for Manufactured Homes Instaations (Manufactured Home Sites, Communities and Setups), ANSI A225.1/NFPA 501A, or with oca codes*. When this range is instaed in a mobie home, it must be secured to the foor during transit. Any method of securing the range is adequate as ong as it conforms to the standards isted above. Four-wire power suppy cabe must be used in a mobie home instaation. The appiance wiring wi need to be revised. See four-wire eectrica connection, Pane B. Copies of the standards isted may be obtained from: Nationa Fire Protection Association Batterymarch Park Quincy, Massachusetts Important: Observe a governing codes and ordinances. Grounded eectrica outet is required. See Eectrica requirements, Pane B. Cabinet opening dimensions that are shown must be used. Do Not pinch the power suppy cord between the range and the wa. Do Not sea range to side cabinets. Note: 24 min. when bottom of wood or meta cabinet is protected by not ess than /4 fame retardant miboard covered with not ess than No. 26 MSG sheet stee, (0.4 mm) stainess stee, auminum or copper. 30 min. cearance between the top of the cooking patform and the bottom of an unprotected wood or meta cabinet. Toos needed for instaation: Phiips c fat-bade screwdriver or Eectrica requirements ai * Eectrica Shock Hazard Eectricay ground range. Faiure to foow this instruction coud resut in death, fire or eectrica shock. If codes permit and a separate grounding wire is used, it is recommended that a quaified eectrician determine that the grounding path is adequate. Do Not ground to a gas pipe. Check with a quaified eectrician if you are not sure range is grounded. Do Not have a fuse in the neutra or grounding circuit. Ony a power suppy cord kit rated at 250 vots, 40 amperes and investigated for use with ranges shoud be used. Do Not pug the pigtai power cord into a ive wa receptace before the cord is permanenty connected to the termina bock. Anti-tip bracket: The foor anti-tip bracket MUST be instaed. To insta the anti-tip bracket shipped with the range, see Pane C and the anti-tip bracket tempate. PI A four-wire or three-wire, singe-phase,. 120/240-vot, 60.Hz; 50.amp, AC-ony, eectrica suppy (or four-wire or three-wire 120/208-vot if specified on the mode/seria rating pate) is required on a separate 40.ampere circuit, fused on both sides of the ine. A time-deay fuse or circuit breaker is recommended. The mode/seria rating pate is ocated on the oven frame behind the door. /B./ THE RANGE MUST BE CONNECTED WITH COPPER WIRE ONLY. hand or eectric dri wood foor: /6 dri bit concrete/ceramic foor: 3/16 carbide-tipped masonry dri bit Parts suppied for instaation: Pane A screws pastic anchors Bracket must be securey mounted to sub-foor. Thickness of fooring may require onger screws to anchor the bracket to sub-foor.

3 4-wire wa 3-wire wa receptace receptace (14-50R) (1 o-50r) Figure 1 Figure 2 Four-wire instaation is recommended n requirement for mobie homes: This E appiance is manufactured with ground connected to cabinet. The ground must be revised so the green grounding wire of the four-wire power suppy cord is connected to the cabinet. When a four-wire receptace of NEMA type 14-50R is used (See Figure ), a matching U.L.-isted, four-wire, 250~vot, 40-ampere, range power suppy cord (pigtai) must be used. This cord contains four copper conductors with ring terminas on the appiance end, terminating in a NEMA Type 14-50P pug on the suppy end. The fourth (grounding) conductor must be identified by a green or green/yeow cover and the neutra conductor by a white cover. Cord shoud be Type SRD or SRDT with a U.L.- isted strain reief and be at east four feet ong. The MINIMUM conductor sizes for the copper four-wire power suppy cord are: 40-ampere circuit 2, No.-8 conductors 1, No.-10 white neutra 1, No.-8 green grounding JD.I Three-wire instaation if a four-wire system is not avaiabe: Loca codes may permit the use of a U.L.-isted, 250-vot, 40-ampere range power suppy cord (pigtai). This cord contains three, No.-10 copper wires and matches a three-wire receptace of NEMA Type o-50r, shown in Figure 2. Connectors on the appiance end must be ring terminas. A U.L.-isted strain reief must be used to connect the power suppy cord to the range. E- This range shoud be connected directy to n the fused disconnect or circuit breaker box - through fexibe, armored or non-metaic sheathed, copper cabe (with grounding wire). Locate the junction box to aow two to three feet of sack in the ine so that the range can be moved if servicing is ever necessary. Do Not cut the conduit. A U.L.-isted conduit connector must be provided at each end of the power suppy cabe (at the range and at the junction box). Wire sizes and connections must conform to the requirements of the Nationa Eectrica H Code, ANSVNFPA 70 - atest edition (*, see E Pane A) and a oca codes and ordinances for the kiowatt rating of the range (40-amperes). IG I 1 I The wiring diagram is aso ocated on the. back of the range. Now start... with range in kitchen. 1 Excessive Weight Hazard Use two or more peope to move and insta range. Faiure to foow this instruction coud resut in back or other injury. When moving range, side range onto cardboard or hardboard to prevent damaging the foor covering. L- Put on safety gasses and goves. Remove shipping materias, tape and protective fim H from range. Keep cardboard bottom and shipping base under range. Remove oven racks and parts package from inside oven. Take four cardboard corners from the carton. Stack one cardboard corner on top of another. Repeat with other two corners. Pace them engthwise on the foor behind the range - to support the range when it is aid on its back. Firmy grasp the range and genty ay it on its back on the cardboard corners. / Pu cardboard shipping base firmy to remove. 141 n Use an adjustabe wre the eveing egs four c E Pace cardboard or hardboard in front of range. Stand range back up onto cardboard or hardboard. L Eectrica Shock Hazard Disconnect power to the junction box before making connection. Eectricay ground range. Faiure to foow these instructions coud resut in death, fire or eectrica shock. This range must be connected to a grounded, metaic, permanent wiring system, or a grounding connector shoud be connected to the grounding termina or wire ead on the range. cover -6- Remove the termina bock cover ocated on. the back of range. /71 Depending on your eectrica suppy, make. the four-wire or three-wire connection to the range foowing the Power suppy cord method or Direct wire method instructions. knockout opening, for 40- ampere power suppy cord Figure 3 J knockout opening for power s,ubppdy 1. Disconnect the power suppy. 2. Remove the knockout for the 40-ampere power suppy cord. 3. Assembe a U.L.-isted strain reief in the opening. 4. Insert the power suppy cord through the strain reief, aowing enough sack to easiy attach the wiring to the termina bock. 5. Use ony ring-type terminas to connect the power suppy. To secure the power suppy cord, use the 3/8 brass nuts attached to the knockout opening. Be sure nuts are instaed tight. 6. Compete eectrica connection according to your type eectrica suppy ( Four-wire eectrica connection or Three-wire eectrica connection ). Four-wire eectrica connection: I grounding - ink Y3 Screw Figure 4 Use this method for mobie homes and whenever four-wire instaation is required. 7. Remove the grounding-ink screw from the range frame. Save the grounding-ink screw. Bend up the grounding ink so that it does not contact the range. See Figure 4. green grounding wire Figure 5 8. Connect the green grounding wire from power suppy cord to the range using the grounding-ink screw. The grounding wire must be attached first and must not contact any other termina. See Figure 5. siver- reief, 3. Connect the neutra (center wire) wire to the center, siver-coored termina screw on the termina bock using the brass nuts that are attached to the termina bock cover. See Figure Connect the other two wires to the outer terminas on the termina bock. See Figure 6.. Do Not oosen the factory instaed nuts aready on the termina. Tighten nuts with 3/8 nut driver for proper eectrica connection. 12. Tighten the strain reief screws. 13. Repace the termina bock cover. and 40-ampere Three-wire eectrica connection: siver- ine /r --- \ U.L.-isted strain reief and 40-ampere range power suppy cord Figure 7 Use this method ONLY if oca codes PERMIT connecting cabinet-grounding conductor to neutra wire of power suppy cord. 7. Use the brass termina nuts attached to the termina bock cover to connect the neutra wire (center wire) to the siver-coored termina screw on the termina bock. See Figure Connect the other two wires to outer termina screws on the termina bock. See Figure Do Not oosen factory-instaed nuts aready on the termina. Tighten nuts with 3/8 nut driver for proper eectrica connection. O.Tighten the strain reief screws..reinsta the termina bock cover. 1. Disconnect the power suppy. 2. Remove the knockout for the power suppy cabe. 3. Assembe a U.L.-isted conduit connector in the power suppy cabe opening. 4. Strip outer covering back 3 inches from end, exposing the wires. Strip the insuation back 1 inch from the end of each wire. 5. Form the bare wire into a U shaped hook. 6. Insert the power suppy 7=i 3 cabe through the conduit connector, aowing enough -m sack to easiy attach the wiring termina bock. 1 -WI 7. Compete eectrica connection according to your type eectrica suppy ( Four-wire eectrica connection or Three-wire eectrica connection ). b R Pane B

4 Four-wire eectrica connection: ing ew 8. Remove the grounding-ink screw from the range frame. Save the grounding-ink screw. Bend up the grounding ink so that it does not contact the range. See Figure 8. bare wire from powe suppi cabe groundingink screw 9. Connect the bare grounding wire from power suppy cabe to the range using the grounding-ink screw. The grounding wire must be attached first and must not contact any other termina. See Figure 9 Tip Over Hazard Connect anti-tip bracket to the range. Reconnect anti-tip bracket, if the range is moved. Do not push down on the open oven door. Foow the instaation instructions. Do not et chidren cimb onto the oven door. Faiure to foow these instructions can resut in death, burns, or other injury. Line up hoes in anti-tip. bracket with hoes in foor. Use the screws provided to fasten anti-tip bracket to foor. NOTE: Anti-tip bracket must be mounte securey to the sub foor. Depending on the thickness of your fooring, onger screws may be necessary to anchor the bracket to the sub foor. Longer screws are avaiabe from your oca hardware store. Move range cose to cabinet opening.. Pug power suppy cord into grounded outet or connect power suppy cabe to junction box. See Eectrica requirements, panes A and B for detais. 88:88 shoud appear in the cock dispay. Remove cardboard or hardboard from under range. Carefuy move range siver-coored bare wire from power suppy cab connector and Figure 10 wg:r suppy IO. Connect the neutra wire (white wire) to the center, siver-coored termina screw on the termina bock using the brass nuts that are attached to the termina bock cover. See Figure 10. I. Connect the other two wires to the outer terminas on the termina bock. See Figure Do NOT oosen the factory instaed nuts aready on the termina. Tighten nuts with 3/8 nut driver for proper eectrica connection. 13. Tighten the ocking ring and camping screws of the conduit connector. 14. Repace the termina bock cover. Three-wire eectrica connection: Use this method ONLY if oca codes PERMIT connecting cabinet-grounding conductor to neutra wire of power suppy cabe. 3. Use the brass termina nuts attached to the knockout opening to connect the neutra wire (white wire) to the siver-coored termina screw on the termina bock. See Figure. 3. Connect the other two wires to outer termina screws on the termina bock. See Figure. IO.Do Not oosen factory-instaed nuts aready on the termina. Tighten nuts with 318 nut driver for proper eectrica connection. I1.Tighten the ocking ring and camping screws of the conduit connector. 12,Reinsta the termina bock cover. 1 Excessive Weight Hazard Use two or more peope to move and insta range. Faiure to foow this instruction can resut in back or other injury Firmy grasp the range and genty ay it on its back on the cardboard corners. Pu cardboard bottom and shipping base firmy to remove. E 0 n Pace cardboard or hardboard in front of range. Stand range back up onto cardboard or hardboard. Eectrica Shock Hazard Take specia care when driing hoes into the foor. Eectrica wires or pumbing may be ocated beneath foor. Locate the eectrica circuits that coud be affected by the instaation of this bracket and turn off power to these circuits. Faiure to foow these instructions may resut in death, fire or eectrica shock. II 1 =I I 1 Pace the anti-tip bracket tempate on the foor in the I I cab/net opening so that the eft edge is against cabinets and the top edge is against the rear wa, moding or cabinet. If opening is deeper than 25 inches, measure and mark a distance 25 inches in from front of opening and aign tempate with mark (or subtract 25 inches from depth and add the difference to the corresponding dimension). If is not fush to the side of cabinet opening, aign the eft side of the tempate to aow for the overhang. Tape the range anti-tip bracket tempate in pace. f i 25 over 24 cabinet Countertop overhangs cabinet side. A = Difference between irth II Contact a quaified foor covering instaer for the best procedure of driing mounting hoes through your type foor covering. Before moving, side range onto cardboard or hardboard. To mount anti-tip. bracket to wood foor, use the anti-tip bracket tempate to mark where to drifmounting hoes. Use a dri with a 8 dri bit to dri the two hoes. Remove tempate from foor. To mount anti-tip bracket to concrete or ceramic foor, use the anti-tip bracket tempate to mark where to dri mounting hoes. Use a dri with a 3/16 masonry dri bit to dri the two hoes. Remove tempate from foor. Tap pastic anchors into mounting hoes in foor with hammer. and Press on front of storage drawer and reease to open. Pu open to first stop position7 Lift front of drawer to cear white whees in drawer guides. Remove drawer - and set it aside on a protected surface. )17 Look under range (a. fashight may be needed) to check that eft rear eveing eg is engaged in the anti-tip bracket. If eveing eg is not propery engaged, remove and v reposition the anti-tip bracket to u insure that the eveing eg fits propery in the anti-tip bracket. Pace rack in oven. Pace e rack, first side to side; then front to back. If the range is not eve, pu range forward unti the rear eveing eg is removed from the anti-tip bracket. Adjust the eveing egs up or down. Then side range back into position. Check that eveing eg is engaged in anti-tip bracket. NOTE: Oven must be eve for satisfactory baking conditions. PI Insert. storage drawer into side rais on sides of drawer opening. Lift front of drawer sighty and push firmy to cose drawer. Push in and. turn each 120 surface unit contro knob to HI position. Check the operation of the cooktop eements and indicator ights. OFF 12 Press the Cock Set button. TIME, HR. AND MIN wi ight up in the dispay. 0:OO wi appear and the : wi be fashing. Press the number buttons for the correct time of day. Press Stat-t/Enter button to start the cock. )22/ Check the operation of the oven eement.. Press the BAKE button. 350 wi appear In the temperature dispay. The ON, Bake Eement, Outer Broi Eement and Oven Cavity symbos wi ight up in the dispay. Press the Start/Enter button. The bottom eement shoud gow red and the indicator ight shoud be on. The upper eement shoud become hot but not gow red. The oven indicator ight goes off when the oven is preheated. Press Cance/OFF button. B- Check the operation of the broi eement.. Press the BROIL button. 500 wi appear in the temperature dispay. The ON, Inner and Outer Broi Eements and Oven Cavity symbos wi ight up in the dispay. Press the Start/Enter button. The top eement shoud gow red and the indicator ight shoud be on. Press the Cance/OFF button. Pane C

5 If range does not operate... Check that the circuit breaker is not tripped or the house fuse bown. Check that power suppy cord is pugged into wa receptace. NOTE: Refer to Use and Care Guide for operating instructions and ceaning instructions. Injury Hazard Because of the weight and size of this range, two or more peope are required to move it. A ranges can tip. Do Not step, ean or sit on the range drawer or door. The anti-tip device packed with range must be instaed. See Instaation Instructions. Faiure to foow these instructions coud resut in injury. For ceaning and maintenanck... If removing the range is necessary for ceaning or maintenance, disconnect the eectrica suppy. If eectrica suppy is inaccessibe, ift the range sighty at the front and pu the range away from the wa. Pu the range out ony as far as necessary to disconnect the eectrica suppy ine. Remove the range to compete ceaning or maintenance. Move range back into operating position. Remove drawer. Leve the range. Reconnect the eectrica suppy. Make sure that eft rear eveing eg is engaged in the anti-tip bracket. If you need assistance... The KitchenAid Consumer Assistance Center wi answer any questions about operating or maintaining your range not covered in the Instaation Instructions. The KitchenAid Consumer Assistance Center is open 24 hours a day, 7 days a week. Just dia the ca is free within the continenta United States. When you ca, you wi need the range mode number and seria number. Both numbers can be found on the mode/seria rating pate ocated on the oven frame behind the door. If you need service... In the event that your KitchenAid appiance shoud need service, ca the deaer from whom you purchased the appiance or a KitchenAidauthorized service company. A KitchenAidauthorized service company is isted in the Yeow Pages of your teephone directory under Appiances - Househod - Major - Service and Repair. You can aso obtain the service company s name and number by diaing, free within the continenta United States, the KitchenAid Consumer Assistance Center teephone number, A specia operator wi te you the name of your nearest KitchenAid-authorized service company. Maintain the quaity buit into your KitchenAid appiance - ca a KitchenAid-authorized service company. Part No Registered Trademark of KitchenAid. KCtchenAid HOME APPLIANCES Prepared by KitchenAid, Benton Harbor, Michigan Printed in Canada