P/N X-SERIES GAUGE AEMnet CAN
|
|
- Magdalene Ellis
- 5 years ago
- Views:
Transcription
1 Instruction Manua P/N X-SERIES GAUGE AEMnet CAN STOP! - READ THIS BEFORE INSTALL OR USE! WARNING: THIS INSTALLATION MAY REQUIRE WELDING OR INTEGRATION INTO A VEHICLE'S ELECTRICAL SYSTEM. DAMAGE TO SENSITIVE ELECTRONICS, FIRE, OR EXPLOSION MAY OCCUR IF PROPER PRECAUTION IS NOT TAKEN. IF THERE IS ANY DOUBT, DO NOT ATTEMPT THE INSTALLATION AND CONSULT A PROFESSIONAL. NOTE: IT IS THE RESPONSIBILITY OF THE ENGINE TUNER TO ULTIMATELY CONFIRM THE CALIBRATION USE FOR ANY PARTICULAR ENGINE IS SAFE FOR ITS INTENDED USE. AEM HOLDS NO RESPONSIBILITY FOR ANY ENGINE DAMAGE THAT RESULTS FROM THE MISUSE OF THIS PRODUCT. Features -/6" / 5mm outer diameter mounting 6 AEMnet channes supported Supported devices: Infinity ECU, Series ECU, EMS- 4, 4 Channe UEGO, X-Series UEGO, VDM Auto-hides channes from devices that aren't present Abiity to hide/show channes from devices that are present Peak reca for each channe US or Metric / SI dispay modes Back beze / facepate suppied; Siver/white avaiabe as optiona purchase Locking connectors Auto-dimming Supports vehice / system votages up to 6V KIT CONTENTS PN 0-03 INST, X-SERIES AEMNET CAN GAUGE GAUGE ASSY, X-SERIES AEMNET CAN GAUGE NUT, KNURLED, M4x0.7 () BRACKET, X-SERIES GAUGE RUBBER BAND, X-SERIES GAUGE CABLE, X-SERIES GAUGE PWR/IO CAN *OPTIONAL* ACCESSORIES PN 30-03ACC BEZEL, X-SERIES SILVER FACEPLATE, X-SERIES AEMNET, WHITE AEM Performance Eectronics, 05 6th Street Unit A, Hawthorne, CA Phone: (30)
2 AEMnet CAN Wiring Instaation Diagram Pin DOCUMENT NUMBER: 0-03 Connector A - Power / IO Coor RED Switched V Power BLACK Power Ground GREEN AEMnet-/ CANL WHITE AEMnet+/ CANH NC NC 07 AEM Performance Eectronics
3 AEMnet CAN Operation The PAGE button may be depressed to scro through the avaiabe AEMnet channes; an abbreviation of each channe name wi be briefy dispayed after each button press. The inner numeric LEDs and outer ring LED dispay the currenty seected channe reading. Channes wi ony be present in the channe ist if the corresponding AEMnet device is presenty connected to the bus, powered, and transmitting. Pease reference the AEMnet Channe description tabe further on in this document. PAGE and PEAK buttons are ocated on the face of the gauge and are used to perform various functions, described beow. Dispay or cear stored peak vaue Press the PEAK button; the peak (highest) reading of the currenty seected channe wi be dispayed and the outer LED wi fash. The peak vaue wi be retained across power cyces. Whie the peak vaue is being dispayed, depress and hod the PEAK button for three seconds unti "CLr" appears to cear the peak vaues. This operation wi cear the peak vaues of ALL channes. Wi be dispayed to confirm the peak vaue has been reset The gauge wi return to norma dispay mode a few seconds after the ast button press Change channe dispay units US / SI (metric) Change wideband O dispay units / Lambda The gauge shoud be in its norma dispay mode, The gauge shoud be in its norma dispay mode, showing a showing the current parameter reading. wideband/oxygen sensor channe reading. Depress and hod the PAGE button for three Depress and hod the PAGE button for three seconds unti seconds unti US or SI appears. US or SI appears. Press the PAGE button to togge between US or SI Press the PAGE button to togge between or Lambda (metric) modes. modes. This setting wi appy to a channes EXCEPT This setting wi appy to a wideband O channes. wideband O channes. The gauge wi return to norma dispay mode a few seconds The gauge wi return to norma dispay mode a few after the ast button press. seconds after the ast button press. Hide or show channes If mutipe AEMnet devices are present on the bus, the channe ist can grow to be quite ong, up to 6 channes. This can make it time consuming to scro through and find a specific channe to dispay. A hide/show feature is avaiabe to remove infrequenty viewed channes from the channe ist. Depress both the PAGE and PEAK buttons to dispay "HidE" and begin seecting which channes to hide/show in the channe ist. Use the PAGE button to scro through the channe ist and the depress the PEAK button to togge between hide and show. The gauge wi return to norma dispay mode a few seconds after the ast button press. A outer LEDs iuminated = SHOW DOCUMENT NUMBER: 0-03 A outer LEDs off = HIDE 07 AEM Performance Eectronics
4 AEMnet CAN Facepate / Beze Instaation The gauge kit is suppied assembed with a back facepate and back beze. An accessory kit is avaiabe (for purchase through AEM deaers) which incudes an optiona siver beze and white facepate. Pease reference the Optiona Accessories section earier in the document for the appropriate part numbers. Contact your deaer or visit for more information. The facepate may be reversibe, dispaying aternative scaings on either side. Reference the Operation section of this manua for detais on how to switch the dispay mode when reversing the facepate. Disassemby is required to change the facepate, fip/reverse the facepate, or change the beze of the gauge. The foowing diagram wi provide famiiarization with the major components of the gauge prior to beginning the procedure. Item DOCUMENT NUMBER: 0-03 Qty 3 Lens Beze Facepate Diffuser Light Guide Button Mounting Stud (M4 x 0.7) Assemby Screw Mounting Bracket Brass Thumb Screw (M4 x 0.7) Printed Circuit Board (PCB) 07 AEM Performance Eectronics
5 AEMnet CAN 5 Gauge Disassemby STEP - Remove the three assemby screws (8) using a # Phiips head screwdriver. Separate the beze () and cup (7) from the rest of the assemby. If you have purchased the optiona accessory kit, the siver beze may be repaced for the existing beze at this time STEP - Separate the PCB () from the remaining components STEP 3 - Side the ight guide (5) upward to remove it, the buttons may fa out at this time - take care not to ose them STEP 4 - As you separate the remaining components, diffuser (4), facepate (3), ens (), note the order in which they were assembed. The facepate (3) may now be reversed to dispay an aternate scaing or repaced for a different coor as incuded in the optiona accessory kit DOCUMENT NUMBER: AEM Performance Eectronics
6 AEMnet CAN 6 Gauge Assemby STEP - Pace the ight guide (5) on a fat surface (back side up) and side the buttons (6) into the sots STEP - Stack the diffuser (4), facepate (3), and ens () in order, over the buttons, and on to the ight guide STEP 3 - Reassembe the PCB and dispay stack with the beze, making sure screw hoes are aigned through the entire assemby STEP 4 - Reassembe and tighten screws to in-b (previousy assembed beze) or 3 in-b (new beze). Do not over-tighten! DOCUMENT NUMBER: AEM Performance Eectronics
7 AEMnet CAN Gauge Instaation Instaation using suppied bracket Instaation w ithout bracket, using rubber band A -/6" (5mm) hoe is required to mount the X-Series gauge. A bracket and thumbscrews are provided to faciitate instaation into a pane or gauge pod. In some cases, the gauge cup may be pushed into a mounting hoe causing an interference fit strong enough to retain the gauge; the suppied rubber band may be fit to the gauge to create a tighter fit in mounting hoes sighty arger than 5mm. It is, however, recommended that gauges be mounted securey using the suppied bracket to ensure they never become oose and cause a hazard during vehice operation. Note: The gauge is not water-proof and shoud not be instaed in a ocation with exposure to water or snow. Damage caused by water ingress wi not be covered under warranty. AEMnet Channes Dispay Labe AF.Fb AFr. AFr. ALt batt bst.d bst.t CUt.S CYL. CYL. CYL. CYL. CYL. CYL. CYL.3 CYL.3 CYL.3 CYL.4 CYL.4 CYL.4 CYL.5 CYL.5 CYL.5 CYL.6 CYL.6 Inj LambdaFB Lambda Lambda Atitude Battery Vots Boost Contro Duty Boost Target SparkCut [RPM] Lambda Lambda Lambda Lambda Lambda Lambda Lambda 3 Lambda 3 Lambda 3 Lambda 4 Lambda 4 Lambda 4 Lambda 5 Lambda 5 Lambda 5 Lambda 6 Lambda DOCUMENT NUMBER: 0-03 US ft V rpm SI m V kpa rpm Source VDM 4 Channe UEGO set on MODE 4 Channe UEGO set on MODE 3 4 Channe UEGO set on MODE 6 4 Channe UEGO set on MODE 4 Channe UEGO set on MODE 4 4 Channe UEGO set on MODE 6 4 Channe UEGO set on MODE 4 Channe UEGO set on MODE 3 4 Channe UEGO set on MODE 6 4 Channe UEGO set on MODE 4 Channe UEGO set on MODE 4 4 Channe UEGO set on MODE 7 4 Channe UEGO set on MODE 4 Channe UEGO set on MODE 3 4 Channe UEGO set on MODE 7 4 Channe UEGO set on MODE 4 Channe UEGO set on MODE 4 07 AEM Performance Eectronics
8 AEMnet CAN CYL.6 CYL.7 CYL.7 CYL.8 CYL.8 E.SPd EtH G.Lat G.Lon G.SPd GEAr Ign.r Ign.t InJ.d LoAd o- o- o-3 o-4 o-5 o-6 o-7 o-8 Pbro PbSt PCLt PFUE POIL PPAn SLIP SPd tab tclt tiat toil ttrn tps Lambda 6 Lambda 7 Lambda 7 Lambda 8 Lambda 8 Engine Speed FexContent Latera Acceeration Inine Acceeration Vehice Speed Gear Cacuated Knock FB (max) Ignition Timing Primary Inj Duty Load Lambda Lambda Lambda 3 Lambda 4 Lambda 5 Lambda 6 Lambda 7 Lambda 8 Baro Press MAP Cooant Pressure Fue Pressure Oi Pressure Crankcase Pressure TC_SipMeasured Vehice Speed Airbox Temp Cooant Temp Intake Air Temp Oi Temp Trans Temp Throtte rpm g g mph n/a deg deg inhg mph mph rpm g g kph n/a deg deg kpa kpa bar bar bar kpa kph kph 4 Channe UEGO set on MODE 7 4 Channe UEGO set on MODE 4 Channe UEGO set on MODE 3 4 Channe UEGO set on MODE 4 Channe UEGO set on MODE 4 VDM VDM VDM EMS Series / EMS-4 FAQ / Troubeshooting I instaed my gauge correcty and the dispay just shows "CAn" The gauge is not detecting the expected AEMnet/CAN traffic. Pease check that you have other AEMnet enabed devices connected to the bus, propery terminated, and powered on. For custom instaations, refer to the Bosch CAN.0b specification for proper wiring and termination techniques. What pins are used in the connector? To popuate optiona extras, use JST P/N SPUD-00T-P0.5 terminas for -6 AWG wire. For support, contact AEM Technica Support at or gentech@aemeectronics.com DOCUMENT NUMBER: AEM Performance Eectronics
9 AEMnet CAN Specifications Dimensions Suppy Votage Suppy Current (3.8V) Operating Temperature diameter (beze) diameter (cup) depth (inc. beze) depth (cup ony) min max nomina min max (6V Suppy).40 -/ / / 85 in in in in VDC VDC ma / / Month Limited Warranty Advanced Engine Management Inc. w arrants to the consumer that a AEM High Performance products w i be free from defects in materia and w orkmanship for a period of tw eve () months from date of the origina purchase. Products that fai w ithin this -month w arranty period w i be repaired or repaced at AEM s option, w hen determined by AEM that the product faied due to defects in materia or w orkmanship. This w arranty is imited to the repair or repacement of the AEM part. In no event sha this w arranty exceed the origina purchase price of the AEM part nor sha AEM be responsibe for specia, incidenta or consequentia damages or cost incurred due to the faiure of this product. Warranty caims to AEM must be transportation prepaid and accompanied w ith dated proof of purchase. This w arranty appies ony to the origina purchaser of product and is non-transferabe. A impied w arranties sha be imited in duration to the said -month w arranty period. Improper use or instaation, accident, abuse, unauthorized repairs or aterations voids this w arranty. AEM discaims any iabiity for consequentia damages due to breach of any w ritten or impied w arranty on a products manufactured by AEM. Warranty returns w i ony be accepted by AEM w hen accompanied by a vaid Return Merchandise Authorization (RMA) number. Product must be received by AEM w ithin 30 days of the date the RMA is issued. UEGO oxygen sensors are considered w ear items and are not covered under w arranty. Pease note that before AEM can issue an RMA for any eectronic product, it is first necessary for the instaer or end user to contact the EMS tech ine at to discuss the probem. Most issues can be resoved over the phone. Under no circumstances shoud a system be returned or a RMA requested before the above process transpires. AEM w i not be responsibe for eectronic products that are instaed incorrecty, instaed in a non-approved appication, misused, or tampered w ith. Any AEM eectronics product can be returned for repair if it is out of the w arranty period. There is a minimum charge of $50.00 for inspection and diagnosis of AEM eectronic parts. Parts used in the repair of AEM eectronic components w i be extra. AEM w i provide an estimate of repairs and receive w ritten or eectronic authorization before repairs are made to the product DOCUMENT NUMBER: AEM Performance Eectronics
P/N X-SERIES GAUGE VOLTAGE 8 TO 18V
Instruction Manual P/N 30-0303 X-SERIES GAUGE VOLTAGE 8 TO 8V STOP! - READ THIS BEFORE INSTALL OR USE! WARNING: THIS INSTALLATION REQUIRES WELDING AND INTEGRATION INTO A VEHICLE'S ELECTRICAL SYSTEM. DAMAGE
More informationP/N X-SERIES GAUGE GPS SPEEDOMETER
Instruction Manual P/N 333 XSERIES GAUGE GPS SPEEDOMETER STOP! READ THIS BEFORE INSTALL OR USE! WARNING: THIS INSTALLATION MAY REQUIRE WELDING OR INTEGRATION INTO A VEHICLE'S ELECTRICAL SYSTEM. DAMAGE
More informationP/N X-SERIES GAUGE OIL / TRANS / WATER TEMP 300F / 150C
Instruction Manual P/N 30030 XSERIES GAUGE OIL / TRANS / WATER TEMP 300F / 50C STOP! READ THIS BEFORE INSTALL OR USE! WARNING: THIS INSTALLATION MAY REQUIRE WELDING OR INTEGRATION INTO A VEHICLE'S ELECTRICAL
More informationP/N X-SERIES GAUGE EGT 1800F / 1000C
Instruction Manual P/N 300305 XSERIES GAUGE EGT 800F / 000C STOP! READ THIS BEFORE INSTALL OR USE! WARNING: THIS INSTALLATION REQUIRES WELDING AND INTEGRATION INTO A VEHICLE'S ELECTRICAL SYSTEM. DAMAGE
More informationP/N GPS MODULE
Instruction Manual P/N 30-2207 GPS MODULE STOP! - READ THIS BEFORE INSTALL OR USE! WARNING: THIS INSTALLATION MAY REQUIRE WELDING OR INTEGRATION INTO A VEHICLE'S ELECTRICAL SYSTEM. DAMAGE TO SENSITIVE
More informationP/N VEHICLE DYNAMICS MODULE
Instruction Manual P/N 0-220 VEHICLE DYNAMICS MODULE STOP! - READ THIS BEFORE INSTALL OR USE! WARNING: THIS INSTALLATION MAY REQUIRE WELDING OR INTEGRATION INTO A VEHICLE'S ELECTRICAL SYSTEM. DAMAGE TO
More informationPolaris RZR XPT CD-7 Plug & Play Harness Kit
30-2216 Polaris RZR XPT CD-7 Plug & Play Harness Kit AEM Performance Electronics AEM Performance Electronics, 2205 126th Street Unit A, Hawthorne, CA 90250 Phone: (310) 484-2322 Fax: (310) 484-0152 http://www.aemelectronics.com
More informationP/N CHANNEL CAN SENSOR MODULE
Instruction Manual P/N 30-2226 6 CHANNEL CAN SENSOR MODULE STOP! - READ THIS BEFORE INSTALL OR USE! WARNING: THIS INSTALLATION MAY REQUIRE WELDING OR INTEGRATION INTO A VEHICLE'S ELECTRICAL SYSTEM. DAMAGE
More informationP/N Water/Methanol Injection V2 Nozzle Kit Includes T-Fitting, Hose, 250cc, 500cc, & 1000cc Jets STOP!
Instruction Manual P/N 30-3312 Water/Methanol Injection V2 Nozzle Kit Includes T-Fitting, Hose, 250cc, 500cc, & 1000cc Jets STOP! THIS PRODUCT HAS LEGAL RESTRICTIONS. READ THIS BEFORE INSTALLING/USING!
More informationP/N Water/Methanol Injection V2 1-Gallon Tank With Conductive Fluid Level Sensor* STOP!
Instruction Manual P/N 30-3325 Water/Methanol Injection V2 1-Gallon Tank With Conductive Fluid Level Sensor* STOP! THIS PRODUCT HAS LEGAL RESTRICTIONS. READ THIS BEFORE INSTALLING/USING! THIS PRODUCT MAY
More information25-30XBK HONDA ADJUSTABLE FUEL PRESSURE REGULATOR
Read and understand these instructions BEFORE attempting to install this product. Do not smoke while working on the fuel system. Keep open flames or sparks away from your work area. Be sure to relieve
More informationP/N INST, X-SERIES UEGO GAUGE. Bosch LSU4.9
Instruction Manual P/N 3-3 X-SERIES UEGO GAUGE Bosch LSU4.9 STOP! - READ THIS BEFORE INSTALL OR USE! WARNING: THIS INSTALLATION MAY REQUIRE WELDING OR INTEGRATION INTO A VEHICLE'S ELECTRICAL SYSTEM. DAMAGE
More informationP/N Water/Methanol Injection V2 Standard Controller Internal MAP with 35psi Max STOP!
Instruction Manual P/N 30-3304 Water/Methanol Injection V2 Standard Controller Internal MAP with 35psi Max STOP! THIS PRODUCT HAS LEGAL RESTRICTIONS. READ THIS BEFORE INSTALLING/USING! THIS PRODUCT MAY
More informationINSTALLATION AND MAINTENANCE MANUAL for ST400-C339 SOLENOID VALVE
04666358 Edition 2 February, 1999 INSTALLATION AND MAINTENANCE MANUAL for ST400-C339 SOLENOID VALVE. IMPORTANT SAFETY INFORMATION ENCLOSED. READ THIS MANUAL BEFORE OPERATING VALVE. IT IS THE RESPONSIBILITY
More informationFord EV6 Injector Adapter Harness User Manual
Ford EV6 Injector Adapter Harness User Manual 30-3805- THIS PRODUCT IS LEGAL IN CALIFORNIA FOR RACING VEHICLES ONLY AND SHOULD NEVER BE USED ON PUBLIC HIGHWAYS. AEM Performance Electronics AEM Performance
More informationGM Stepper Idle Adapter User Manual
GM Stepper Idle Adapter User Manual 30-3805-07 THIS PRODUCT IS LEGAL IN CALIFORNIA FOR RACING VEHICLES ONLY AND SHOULD NEVER BE USED ON PUBLIC HIGHWAYS. AEM Performance Electronics AEM Performance Electronics,
More informationUSER INSTRUCTIONS USER INSTRUCTIONS. Innovative Car Alarm. Thatcham M.I.R.R.C. Evaluation No: TC2-1065/0199
USER INSTRUCTIONS USER INSTRUCTIONS Innovative Car Aarm Thatcham M.I.R.R.C. Evauation No: TC2-1065/0199 IMPORTANT WARNING The Cobra 7928/26/HF Aarm Immobiiser is a Category 1 MIRRC Thatcham isted security
More informationINSTRUCTION MANUAL LITHIUM-ION POLYMER MINI JUMP STARTER (KIT SET) SC POWER SCB22
INSTRUCTION MANUAL LITHIUM-ION POLYMER MINI JUMP STARTER (KIT SET) Technica Specifications SCB22 Battery Type: Lithium-Ion Poymer Battery Capacity: 2200 mah (12V DC) Crancking Ampere: 220 A Peak Current:
More informationGM Throttle Body Adapter Harness User Manual
GM Throttle Body Adapter Harness User Manual 30-3809-01 THIS PRODUCT IS LEGAL IN CALIFORNIA FOR RACING VEHICLES ONLY AND SHOULD NEVER BE USED ON PUBLIC HIGHWAYS. AEM Performance Electronics AEM Performance
More informationANTILOCK BRAKE SYSTEM
SECTION 4F ANTILOCK BRAKE SYSTEM Caution: Disconnect the negative battery cabe before removing or instaing any eectrica unit or when a too or equipment coud easiy come in contact with exposed eectrica
More informationClamping devices. CLAMPEX clamping elements offer new possibilities as a shaft-hub-connection:
Keyess camping devices Camping devices Genera description: CLAMPEX are keyess camping devices designed to transmit torque via friction on mating components. These designs produce high transmittabe torque
More informationModel TWS. Swirl Diffusers
Mode TWS Swir Diffusers Mode TWS Advanced Air s new range of high performance TWS ceiing swir diffusers have been designed to deiver the high air change rates required to meet the demand of high oads.
More informationP/N X-Series Wideband UEGO AFR Gauge w/ OBD CAN Integration
Instruction Manual P/N 0-0 X-Series Wideband UEGO AFR Gauge w/ OBD CAN Integration Bosch LSU.9 STOP! - READ THIS BEFORE INSTALL OR USE! WARNING: THIS INSTALLATION MAY REQUIRE WELDING OR INTEGRATION INTO
More informationMulti-Input Water/Methanol Injection Harness
Multi-Input Water/Methanol Injection Harness 30-3324 WARNING: Improper installation and/or adjustment of this product can result in major engine/vehicle damage! Use of this injection system requires proper
More informationUse the emergency flashers if the vehicle malfunctions or is involved in an accident. ITO51P101
Emergency fashers Use the emergency fashers if the vehice mafunctions or is invoved in an accident. Press the switch to fash a the turn signa ights. To turn them off, press the switch once again. ITO51P101
More informationTK35UE 2018 Flashlight
TK35UE 2018 Fashight Technica Parameters ANSI/PLATO FL1 Genera Mode Fash Mode Turbo High Med Low Eco Strobe SOS Output Tactica Mode Outdoor Mode 3200 2000 1000 350 100 20 3200 100 1h 30min 2h 3h 40min
More informationFlex Fuel Sensor Kit (Barbed) Flex Fuel Sensor Kit (-6AN)
0-00 Flex Fuel Sensor Kit (Barbed) 0-0 Flex Fuel Sensor Kit (-6AN) THIS PRODUCT IS LEGAL IN CALIFORNIA FOR RACING VEHICLES ONLY AND SHOULD NEVER BE USED ON PUBLIC HIGHWAYS. AEM Performance Electronics
More informationInstallation Instructions for AEM Serial Gauge
Installation Instructions for 30-4300 AEM Serial Gauge WARNING: This installation is not for the electrically or mechanically challenged! Use this gauge with EXTREME caution! If you are! uncomfortable
More informationPart Number Analog EGT Gauge
Part Number 30-5131 Analog EGT Gauge Figure 1. Wiring Schematic AEM EGT Gauge Parts 1 x 35-5131(B/W) EGT Gauge Assembly 1 x 30-2065 EGT Sensor Thermocouple w/mount 1 x 35-4302 Install Kit (6 Butt Connectors)
More informationUser Manual. 12 Volt Battery Charger THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS READ ENTIRE INSTRUCTION BEFORE USE
User Manua 12 Vot Battery Charger Pus Battery maintainer and Rejuvenator THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS READ ENTIRE INSTRUCTION BEFORE USE Mode No. 60134 / 60138 1 WARNING
More informationOil Pressure Display Gauges Part numbers: Analog Oil/Fuel SAE Pressure Gauge psi Analog Oil SAE Pressure Gauge.
Oil Pressure Display Gauges Part numbers: 30-5133 - Analog Oil/Fuel SAE Pressure Gauge. 0-100psi 30-5135 - Analog Oil SAE Pressure Gauge. 0-150psi AEM's Analog style Oil Pressure Gauges feature quick response
More informationPart Number AEM 4-CH WIDEBAND UEGO CONTROLLER
Part Number 30-2340 AEM 4-CH WIDEBAND UEGO CONTROLLER FIGURE 1. WIRING DIAGRAM AEM Performance Electronics 2205 126 th Street Unit A, Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152 http://www.aemelectronics.com
More informationAny switch configuration
Series L2 Rotary Cam es Attractive design, reiabe operation and high quaity for any appication up to 25 Amps TIP! Sprecher + Schuh s comprehensive ine of L2 rotary cam switches are avaiabe for a contro
More informationFenix TK65R Flashlight
BrightGuy.com is an authorized Fenix Distributor Fenix TK65R Fashight 1. Cataput action bet cip 2. Quick-reease button Technica Parameters ANSI/PLATO Genera Mode Fash Mode FL1 Turbo High Med Low Eco Strobe
More informationPart Number Analog Style 15 PSI Fuel/Boost Pressure Gauge. NOTE: Faceplate Configuration Instructions Included on Separate Sheet
Part Number 30-5144 Analog Style 15 PSI Fuel/Boost Pressure Gauge NOTE: Faceplate Configuration Instructions Included on Separate Sheet AEM Oil/Fuel Pressure Gauge Parts 1 x 35-5144 Pressure Gauge Assembly
More information30 Electric ding. IMPORTANT: Read and save these instructions. ALL RANGES CAN TIP INJURY TO PERSONS COULD RESULT SEE INSTALLATION INSTRUCTIONS
Part No. 9752387 ALL RANGES CAN TIP INJURY TO PERSONS COULD RESULT INSTALL ANTI-TIP DEVICE PACKED WITH RANGE SEE INSTALLATION INSTRUCTIONS 30 Eectric ding IMPORTANT: Read and save these instructions. IMPORTANT:
More informationENGINE CONTROL (22R E)
ENGINE CONTRO (R E) I5 IGNITION S STARTER REAY [R/ NO. ] P N AM ST 5 IG 7 7 C 5 E 4 Y C (FOOR SHIFT) 80A AT P PARK/NEUTRA POSITION S AM (COUMN SHIFT) (NEUTRA START S) I4 C FUSE OX [R/ NO. ] 5 7 I C Y Y
More informationVS235XR / VS255XR. Rechargeable backup battery capability 3-channel transmitter With rolling code & code learning technology. STANDARD FEATURES l
VS235XR / VS255XR Sef-Contained, RF Remote-Controed Vehice Security System Rechargeabe backup battery capabiity 3-channe transmitter With roing code & code earning technoogy CBA STANDARD FEATURES RF Remote
More informationENGINE CONTROL (22R E)
ENGINE CONTRO (R E) SYSTEM OUTINE THE ENGINE CONTRO SYSTEM UTIIZES A MICROCOMPUTER AND MAINTAINS OVERA CONTRO OF THE ENGINE, TRANSMISSION, ETC.. AN OUTINE OF ENGINE CONTRO IS GIVEN HERE.. INPUT SIGNA ()
More informationS.B. 469 for information on GM applications). Both styles are shown in Figure 1. Figure 1
NO: 4263132 SERVICE BULLETIN DATE: January X,1993 Supersedes: S.B. 426R dated 11/7/89 SUBJECT: ZERO-CLEARAN CE GOVERNOR WEIGHT RETAINER ASSEMBLIES In June 1988, Stanadyne introduced a zero-cearance Eastomer
More information10 Ch Peak & Hold Injector Driver PN
Installation Instructions 10 Ch Peak & Hold Injector Driver PN 30-2710 WARNING: installation is not for the electrically challenged! Use this product with extreme caution! If you are uncomfortable with
More informationPart Number cc/min Water/Methanol Injection Flow Gauge
Part Number 30-5141 500 cc/min Water/Methanol Injection Flow Gauge Figure 1. Wiring Schematic This product is legal in California for racing vehicles only and should never be used on public highways. AEM
More informationP/N X-SERIES INLINE WIDEBAND Bosch LSU4.9
Instruction Manual P/N 30-0310 X-SERIES INLINE WIDEBAND Bosch LSU4.9 STOP! - READ THIS BEFORE INSTALL OR USE! WARNING: THIS INSTALLATION MAY REQUIRE WELDING OR INTEGRATION INTO A VEHICLE'S ELECTRICAL SYSTEM.
More informationOwner s Manual & Service Records
Owner s Manua & Service Records Owner s Record A correspondence reating to service probems may be addressed to: SERVICE DEPARTMENT, BAJAJ USA 525 ECCLES AVENUE SOUTH SAN FRANCISCO, CA 94080 Notice: The
More informationOperating instructions CI24RP.. CI30RP..
Operating instructions en CI24RP.. CI30RP.. Tabe of Contents Congratuations.................................................................................. 3 Safety and warning information......................................................................
More informationCruzPro UWSD-10. Ultrasonic 3D Wind Speed/Direction Sensor with NMEA 0183/RS422 Output. Other CruzPro Products
emai: info@cruzpro.com website: www.cruzpro.com Other CruzPro Products Wind Speed/Direction Dispay Depthsounders/w Kee Offset, Deep/Shaow/Anchor Drag Aarms PC Based DSP Fishfinder for Windows98, XP, 2000,
More information65E CONTROL SERIES CONTROLS. Instruction Manual. For DC Input Variable Speed Controls. P.0. Box W. 106th Street Zionsville, Indiana 46077
65E CONTROL ERIE CONTROL Instruction Manua For C Input Variabe peed Contros P.0. Box 0 5000 W. 06th treet Zionsvie, Indiana 46077 Phone (37) 8735 Fax (37) 87305 www.dartcontros.com LT65E (0704) A5376A
More informationInstallation Instructions for: Channel Thermocouple Amplifier
Installation Instructions for: 30-2204 4 Channel Thermocouple Amplifier WARNING: This installation is not fo r the electrically or mechanically challenged! Use this sensor with EXTREME caution! If you
More information<AN002.doc> DALF Application Note #002. Dalf/Simple-H Hookup. Revision 0.02 May 04, 2007
DALF Appication Note #002 Daf/Simpe-H Hookup Revision 0.02 May 04, 2007 Embedded Eectronics Page 1 5/4/2007 Tabe of Contents 1 APPLICATION NOTE SYNOPSIS...2 2 HOOKUP...2 3 PICTURE (DURING TEST)...3
More informationOur policy is one of continuous research and development. We therefore reserve the right
Tubing & Hose Metric Nyon, Poyurethane, Poyester Reinforced PVC, Meta Braided Rubber, Copper, Doube Wa Brazed Stee Avaiabe in a variety of different types to suit a wide range of appications A tubing can
More informationTABLE OF CONTENTS WARRANTY
65E CONTROL ERIE CONTROL Instruction Manua For C Input Variabe peed Contros P.0. Box 0 5000 W. 06th treet Zionsvie, Indiana 46077 Phone (37) 8735 Fax (37) 87305 www.dartcontros.com LT65E (090) A5376 TABLE
More informationENGINE CONTROL (2RZ-FE) SYSTEM OUTLINE
ENGINE CONTRO (RZ-FE) SYSTEM OUTINE THE ENGINE CONTRO SYSTEM UTIIZES A MICROCOMPUTER AND MAINTAINS OVERA CONTRO OF THE ENGINE, TRANSMISSION, ETC. AN OUTINE OF ENGINE CONTRO IS GIVEN HERE.. INPUT SIGNA
More informationEC Series GMS200C. Generator Set Specification. Your Partner for Power. Page of 5
EC Series Generator Set Specification Your Partner for Power Page - 1 - of 5 3-Phase, 50Hz@1500RPM Prime Power Standby Power Votage kw kva Amps 380 160 200 303.9 400 160 200 288.7 415 160 200 278.2 440
More informationGXL SERIES. DC 2-wire type Micro-size Inductive Proximity Sensor. High performance in micro-size design. Versatile mounting. Reduced wiring operation
777 PHOTO PHOTO DC -wire Micro-size Inductive Proximity SERIES Reated Information Genera terms and conditions... F-17 Gossary of terms... P.16~ seection guide... P.77~ Genera precautions... P. Conforming
More informationInternal MAP Water/Methanol Injection Controller ,
Internal MAP Water/Methanol Injection Controller 30-3304, 30-3306 WARNING: Improper installation and/or adjustment of this product can result in major engine/vehicle damage! Use of this injection system
More informationOptional Modes of Operation Pump Control Brake Control - Smart Motor Brake, Accu-stop and Slow Speed with Braking
Controers The Inteigent Controer with extensive starting and stopping configurations up to 1000HP (3-wire), 1400HP (6-wire) The Softstarter Controer provides inteigence, unmatched performance, fexibiity,
More informationCENTRAL PARK - 4 Leg Swing Set
CENTRAL PARK - 4 Leg Swing Set Mode #: 94444 Assembed dimensions are 134" x 93" x 74". Aow 6-12 ft of cearance around the perimeter of the swing set area when fuy assembed. OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS,
More informationInstallation Instructions for: EMS P/N Honda S2000
Installation Instructions for: EMS P/N 30-6052 2000-2005 Honda S2000! WARNING: This installation is not for the tuning novice nor the PC illiterate! Use this system with EXTREME caution! The AEM EMS System
More informationInstallation Instructions for: DT2-AF2 Dual Channel & DT2-AF1 Single Channel Wide Band O2 Sensor Controller for A/F (Lambda) Measurement
Installation Instructions for: DT2-AF2 Dual Channel & DT2-AF1 Single Channel Wide Band O2 Sensor Controller for A/F (Lambda) Measurement WARNING: This installation is not for the electrically or mechanically
More informationInstallation Instructions for NS No Sensor Gauge-Type UEGO Controller
Installation Instructions for 30-4110NS No Sensor Gauge-Type UEGO Controller WARNING: This installation is not for the electrically or mechanically challenged! Use this sensor with EXTREME caution! If
More informationManual. 30C and 45C Load Push and Load Push/Pull. cascad& Cascade is a Registered Trademark of Cascade Corporation
b * Service Manua 30C and 45C Load Push and Load Push/Pu Seria Numbers 667310 through 672356 0 Manua Number 667444 R-2 cascad& Cascade is a Registered Trademark of Cascade Corporation Contents Page Number
More informationSTEPPER DRIVE : E-5042
54, Annapurna Industria Estate, Tiak oad, E L E C T O N I C S Introduction The E-5042 is a fuy digita stepper drive deveoped with advanced DSP contro agorithm based on the atest motion contro technoogy.
More informationAluminium Fixed Blade Return Grilles Series
Auminium Fixed Bade Return Gries 4900 Series Auminium Fixed Bade Return Gries Modes 5145H and 51FH Return Gries have fixed horizonta bades (parae to width/first specified dim.) spaced on 19mm centres with
More informationInstallation Instructions for AEM Tru Boost Boost Controller Gauge
Installation Instructions for 30-4350 AEM Tru Boost Boost Controller Gauge AEM s Tru Boost boost controller gauge is a stand-alone boost controller that features a three digit LED digital readout with
More informationP/N Polaris RZR XP Turbo AEM Infinity Plug and Play Harness STOP!
Instruction Manual 206 Polaris RZR XP Turbo AEM Infinity Plug and Play Harness STOP! THIS PRODUCT HAS LEGAL RESTRICTIONS. READ THIS BEFORE INSTALLING/USING! THIS PRODUCT MAY BE USED SOLELY ON VEHICLES
More informationInstallation Instructions for: EMS P/N Acura NSX
Installation Instructions for: EMS P/N 30-1042 1991-94 Acura NSX! WARNING: This installation is not for the tuning novice nor the PC illiterate! Use this system with EXTREME caution! The AEM EMS System
More informationASSEMBLY AND INSTALLATION
ASSEMBY AND INSTAATION STRAIGT AND EVE GUARDRAIING (using Tpes 10, 15, 20, 21, 25 & 26) Where: = distance between centres of uprights I = ength of horizonta tube = distance from ground to centre ine of
More informationGXL SERIES. DC 2-wire type Micro-size Inductive Proximity Sensor. High performance in micro-size design. Reduced wiring operation. Versatile mounting
1 DC -wire Micro-size Inductive Proximity SERIES Reated Information Genera terms and conditions... F- Gossary of terms... P.176~ guide... P.71~ Genera precautions... P.179~ PHOTO PHOTO IGHT FOW PARTICUAR
More informationBody Length: 21.5cm. Overall Height: 8.5cm. Main Rotor Dia: 19cm. Name Quantity Name Quantity. Helicopter 1 Remote Control!
CONGRATULATIONS ON OWNING THE. SPEED master mini RIC HELICCPTERI THE ULTIMATE INDOOR OUTDOOR MINI HELICOPTER IMPORTANT: For ages 14+ ony! This product is not a toy. To ensure safety, this manua must be
More informationRule No. 16 SERVICE CONNECTIONS, METERS, AND CUSTOMER S FACILITIES
SOUTHERN CALIFORNIA WATER COMPANY Revised Ca. P.U.C. Sheet No. 3450-W SAN DIMAS, CALIFORNIA 91773-9016 Canceing Revised Ca. P.U.C. Sheet No. 3293-W Page 1 of 7 A. Genera 1. Utiity s Responsibiity a. (1)
More informationEP Series WPS150S. Generator Set Specification. Super Quiet, Superior Life! Page of 5
EP Series Generator Set Specification Super Quiet, Superior Life! Page - 1 - of 5 3-Phase, 50Hz@1500RPM Prime Power Standby Power Votage kw kva Amps 380 120 150 227.9 400 120 150 216.5 415 120 150 208.7
More informationLinear Slot Diffusers Series
Linear Sot iffusers 5000 Series Linear Sot iffusers 5000 Series The Series 5000 Linear Sot Ceiing iffuser has been speciay designed to provide both the unobtrusive appearance required for architectura
More information!ijl The way to reaity tty
J4?? s.!!ij The way to reaity tty N 547 W Jackson Bvd. Chicago, L 6066 (32) 322-6900 TTY# -32-322-6774 Date: October 20, 207 To: ALL BDDERS From: Brenda Resendez, Senior Buyer Subject: ADDENDUM No. Metra
More informationN1VS VARIABLE SPEED AIR HANDLERS
(0500) TECHNICAL SPECIFICATIONS VARIABLE SPEED AIR HANDLERS FOR USE WITH SPLIT SYSTEM COOLING AND HEAT PUMP 600-2000 CFM BLOWERS 2-5 TON COILS OPTIONAL1 & 3 Ø ELECTRIC HEATERS DESCRIPTION These variabe
More informationPRECISION PUMP APPLICATOR
User s Manua nstaation & Operating nstructions PRECSON PUMP APPLCATOR For Box, Junior, and Custom Appicators For questions and/or product support contact the TW ROCOL North America Customer Service Department
More informationvw-wi://rl/a.en-gb.a wi:: xml?xsl=3
Page 1 of 13 Removing and instaing turbocharger 1 contro unit -J724- - vehices with 3.0 tr. engine Specia toos and workshop equipment required t Tester -VAS 6395/1- t Connection ead -VAS 6395/4-2- t Open-end
More informationP/N Toyota Supra MKIV Twin Turbo 2JZ-GTE AEM Infinity PnP Harness STOP!
Instruction Manual 1993-1998 Toyota Supra MKIV Twin Turbo 2JZ-GTE AEM Infinity PnP Harness STOP! THIS PRODUCT HAS LEGAL RESTRICTIONS. READ THIS BEFORE INSTALLING/USING! THIS PRODUCT MAY BE USED SOLELY
More informationInstallation Instructions for: EMS P/N Acura Integra Acura 2.3CL Honda Accord Honda Civic
Installation Instructions for: EMS P/N 30-6050 00-01 Acura Integra 98-99 Acura 2.3CL 98-02 Honda Accord 99-00 Honda Civic! WARNING: This installation is not for the tuning novice nor the PC illiterate!
More informationGODREJ & BOYCE MFG. CO. LTD.
GODREJ & BOYCE MFG. CO. LTD. POCKET GUIDE FOR FORKLIFT TRUCK OPERATORS MATERIAL HANDLING EQUIPMENT DIVISION GODREJ & BOYCE MFG. CO. LTD. TO ALL FORKLIFT TRUCK OPERATORS Dear Friends, This booket is speciay
More informationInstallation Instructions for / Universal Water/Methanol Injection Kit
Installation Instructions for 30-3000 / 30-3001 Universal Water/Methanol Injection Kit WARNING: This installation is not for the electrically or mechanically challenged! Use this system with EXTREME caution!
More informationS I G N E X T R U S I O N S & S Y S T E M S. Kit Includes: LED s. Power Supply. Clear Plastic (Not Included) 1/2 Opening. Cap Screw Part #5940
3032 Waker Ridge Dr. NW Grand Rapids, MI To Free: (877) 784-0405 Fax: (1) 784-0411 Wa Mount Tension Frame (Mi Finish) Cover Screw Part #5215 1 4-1/8 1-1/ Fexibe Face (Not Incuded) Mounting Hardware (Not
More informationLastec Articulator. Owner s Manual
Lastec Articuator Mode 325EFD-CE Owner s Manua Manua Part Number: Man-325EFD-CE Lastec A Division of Wood-Mizer Products, Inc. 8180 West 10th Street Indianapois, Indiana 46214 Phone (317) 808-0703 Fax
More informationThread Direction R = Right hand L = Left hand (Not Available for Micro Series) (Refer to leadscrew. Code. availability)
Kerk onventiona s: FW Series Free Wheeing Kerk FW Series conventiona stye, without anti-backash function. The Kerk FW Series genera purpose free-wheeing nut is for appications not requiring anti-backash
More informationReady for the future. ST 1082 mobile column lifts capacity kg
Ready for the future ST 1082 mobie coumn ifts capacity 8.200 kg Two hard and fast aws appy in today s maintenance and repair faciities: time is money and an agreement is an agreement. This is why more
More informationOperating instructions Maintenance instructions
Operating instructions Maintenance instructions Origina operating instructions BPR 45/55 D - BPR 55/65 D S/N 101 692 14... / S/N 101 692 33... / S/N 101 692 16... / S/N 101 692 34... Reversibe Vibrating
More informationOperating instructions Maintenance instructions
Operating instructions Maintenance instructions Origina operating instructions S/N 101 692 26 1434 > / S/N 101 692 35... Reversibe Vibrating Pate Cataogue No. 008 067 61 12/2012 Foreword 1 Foreword BOMAG
More information&OPERATOR S MANUAL BCIOOO BAGGER CART. +-I HONDA DEALER: PLEASE GIVE THIS PUBLICATION TO YOUR CUSTOMERl-+- I I I I I I I I I I I I I I I I I I I I
&OPERATOR S MANUAL BCIOOO BAGGER CART I I I I I I I I I I I I I I I I I I I I +-I HONDA DEALER: PLEASE GIVE THIS PUBLICATION TO YOUR CUSTOMER-+- -- A FEW WORDS ABOUT SAFETY Your safety and the safety
More informationManagement. Telematics for the Working Fleet. Innovative tools forfleet
Innovative toos forfeet Management Teematics for the Working Feet Track driving every second Compare drivers and vehices Retrieve vehice info wireessy ISO 9001 CERTIFIED COMPANY D AV I S I N S T R U M
More informationInstruction Manual P/N Wideband Ethanol Boost Gauge P/N Wideband Ethanol Boost Gauge
Instruction Manual P/N 30-4910 Wideband Ethanol Boost Gauge P/N 30-4911 Wideband Ethanol Boost Gauge! WARNING: This installation is not for the electronic novice or the PC illiterate! Use this system with
More informationFor use anywhere. Many convenient features
Controers IN-rai mounted softstarters up to 85A. Larger softstarter frame sizes up to 480A (400HP @480V) Sprecher + Schuh IN-rai mounted Controers can be direct connected to CA7 contactors to provide isoation
More informationRotary Cam Switches. Rotary Cam Switches
Rotary Cam es Series... 2 Hande Assembies... 8 Accessories... 12 Circuit Diagrams, Technica Information & Dimensions (Onine)... 13 Series R-Line Rotary Cam es... 24 Handes and Accessories... 27 Circuit
More informationInstallation Instructions for Gauge-Type UEGO Controller
Installation Instructions for 30-4100 Gauge-Type UEGO Controller WARNING: This installation is not for the electrically or mechanically challenged! Use this sensor with EXTREME caution! If you are! uncomfortable
More informationInstallation Instructions for: EMS P/N Eclipse Turbo, Talon Tsi, Laser RS Galant VR4
Installation Instructions for: EMS P/N 30-6300 1990-1994 Eclipse Turbo, Talon Tsi, Laser RS Galant VR4! WARNING: This installation is not for the tuning novice nor the PC illiterate! Use this system with
More informationProcyon 1. Product # Type Date Project Name Project Location Prepared By. Construction. Optical System. Product Applications. l l l. l l l.
Product # Type Date Project Name Project Location Prepared By Construction Housing is ow copper die-cast auminum, heavy duty, structuray rigid and vibranty dissipating heat for onger umen maintenance ife-hours.
More information* NOTE: Legal in California only for racing vehicles which may never be used upon a highway
Read and understand these instructions BEFORE attempting to install this product. Failure to follow installation instructions and not using the provided hardware may damage the intake tube, throttle body
More informationOperating instructions Maintenance instructions
Operating instructions Maintenance instructions Origina operating instructions BW 100 AD-4 / BW 120 AD-4 / BW 125 AD-4 BW 100 AC-4 / BW 120 AC-4 / BW 125 AC-4 S/N 101 880 06... > / S/N 101 880 16... >
More informationTD3 Series UNIQUE LIGHTING SOLUTIONS RETROFIT INSTALLATION GUIDE TD3-1-UN-65 TD3-3-UN-65
TD3-1-UN-65 TD3-3-UN-65 RETROFIT INSTALLATION GUIDE UNIQUE LIGHTING SOLUTIONS WARNING Retrofit instaation must ony be performed by a icensed eectrician. To prevent death, injury or damage to property this
More informationSuper-G Slim Module System - Suspension
Super-G Sim Modue System - Suspension ate: Project: mm (3 9/16") IRECT 2 9/16" 65mm L3SGS-SUS-SYS CE R OP Artice # Mounting istribution iffuser Intake profie LE Votage Eectrica Finishes Type / Product
More informationLintra-Lite Actuators Series A44000, Rodless Cylinders Double Acting
Section 11 Lintra-Lite Actuators Series A44000, Rodess Cyinders Doube Acting LINTRA -LITE Series A44000 Rodess Cyinders Series A44000 Features...ACT-11-2 Series A44000 Specifications...ACT-11-3 Series
More informationP/N Nissan Silvia SR20DET AEM Infinity PnP Harness STOP! THIS PRODUCT HAS LEGAL RESTRICTIONS. READ THIS BEFORE INSTALLING/USING!
Instruction Manual 1994-1996 Nissan Silvia SR20DET AEM Infinity PnP Harness STOP! THIS PRODUCT HAS LEGAL RESTRICTIONS. READ THIS BEFORE INSTALLING/USING! THIS PRODUCT MAY BE USED SOLELY ON VEHICLES USED
More information