CENTRAL PARK - 4 Leg Swing Set

Transcription

1 CENTRAL PARK - 4 Leg Swing Set Mode #: Assembed dimensions are 134" x 93" x 74". Aow 6-12 ft of cearance around the perimeter of the swing set area when fuy assembed. OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS, CARE, MAINTENANCE AND USER'S GUIDE WARNING! Pease read this entire instruction and assemby manua competey before proceeding. You must foow a safety instructions whie using this equipment. The surface area where this swing set is set up must be eve and free of a debris. This set is designed to be anchored into the ground and is not to be set up on any hard surfaces such as concrete, hardened soi, or asphat. Proper surfacing under and surrounding the set adds to the safety eve such as sand or much. Read a cautionary statements on the foowing pages before using this equipment and save this instruction manua. DO NOT ALLOW CHILDREN TO PLAY ON THIS GYM SET UNSUPERVISED! CONSTANT ADULT SUPERVISION IS REQUIRED. Do not use when raining or during any incement weather (i.e. rain, seet, snow, ice, high winds, thunderstorms. or ightening). DO NOT ALLOW CHILDREN TO JUMP ON OR CLIMB UP ON THIS SET'S TOP BAR. For warranty detais and registration card see the back page of this manua. FOLLOW ALL ASSEMBLY INSTRUCTIONS AS WRITTEN IN THIS MANUAL Pease retain saes receipt for warranty purposes. DO NOT RETURN THE SET TO THE STORE. If repacement parts or customer service is needed pease contact XDP Recreation by emai at service@xdp-recreation.com or by caing between 8:00am and 5:00pm (Eastern Standard Time), Monday - Friday. This gym is designed to be used safey by up to six (6) chidren, ages 3 years to 8 years, with weight capacity of 100 bs per chid or tota combined weight imit of 600 bs for a six (6) chidren. This pay gym is designed for backyard use ony and is NOT intended for paygrounds, schoos, day care faciities, nurseries or other pubic paces. Foow a assemby instructions carefuy and as directed in this manua. This gym conforms to a safety requirements by ASTM for Home Payground equipment when propery assembed using the instructions encosed. Adut assemby is required. Contains sma parts. For proper stabiity and safety this gym set shoud be instaed with ground anchors. It is highy recommended that you seek the opinion from a oca icensed contractor on the best way to secure the swing set in your ocation. IF NEEDED, GROUND ANCHORS CAN BE BOUGHT FROM THE STORE YOU PURCHASED THIS SET AT OR BY PURCHASING FROM DO NOT XDP RETURN RECREATION'S TO RETAILER WEBSITE AT WHERE PURCHASED. XDP RECREATION LLC, 5910 SHILOH ROAD EAST, UNIT 108, ALPHARETTA, GEORGIA 30005

2 IMPORTANT - INSTRUCTIONS AND WARNINGS WARNING READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT AGE LIMIT This product is designed to be used by up to six (6) chidren between the ages of 3 to 8. Maximum user weight is 100 pounds (45 kg) each with a combined maximum weight of 600 pounds (272kg). The pay set is designed for chidren over three (3) years of age up to (8) years of age. Use by smaer chidren can resut in entrapment or serious injury. On-site adut supervision is required at a times for chidren of a ages. Do not aow use by chidren with any physica condition that may affect his/her abiity to use this equipment safey. Do not aow chidren to use the equipment in a manner other than intended. BEFORE YOU BEGIN Carefuy read a instructions in this manua before assembing and using this product. The unit must be assembed by aduts. Heavy duty working goves must be worn to avoid injuries during assemby. Chidren must not use the equipment unti it is propery assembed and anchored. Adut supervision is required during the use of this equipment at a times. Unpack a parts. Take a compete inventory of a parts and hardware using the parts and hardware ists in the foowing pages. If any parts are missing, do not return to the store. Pease ca customer service to-free number isted on the cover page for assistance. Store the product back in the origina box and do not begin to insta unti a parts are obtained. LOCATION OF PLAY SET The equipment must be paced more than six (6) feet (1.8 meters) from any structures or obstructions, incuding but not imited to buidings, fence, garage, trees, aundry ines, eectrica wires. Chidren can be seriousy injured running or swinging into obstaces. The pay set must be instaed on eve ground. Uneven ground must be eveed prior to instaation. Instaation on soping or uneven ground wi put stress on the joints, causing the unit to become oose and unstabe which may resut in serious injuries. Remove any tripping hazards from the safe pay area, such as roots, tree stumps, rocks, andscaping, sprinker heads, rairoad ties, pumbing and eectrica connections. It is highy recommended that you seek the opinion from a oca icensed contractor on the best way to secure the swing set in your ocation. Windy conditions: it is possibe for the product to be bown about by a high wind. if you anticipate high winds, the frame shoud be secured to the ground with the use of an Anchor kit. If you anticipate severe winds, the product shoud be moved to a shetered ocation or competey disassembed. Anchor kits can be ordered directy from XDP RECREATION at or by caing

3 Do not insta your pay set over hard surface, e.g. asphat, concrete, packed earth, tie or brick foor. A fa onto a hard surface can resut in serious injury or death to the user. The foowing is a ist of recommended ground covers from the Consumer Product Safety Commission: SUGGESTED MATERIAL UNCOMPRESSED DEPTH Doube Shredded Bark Much 9 Uniform Wood Chips 12 Fine Grave 12 Fine Sand 12 The Consumer Product Safety Commission s Outdoor Home Payground Safety Handbook recommends to insta and maintain the payground equipment over at east 9 inches of wood chips, much or shredded rubber (for equipment up to 8 feet high) or sand or pea grave (for equipment no more than 5 feet high) as shock absorbing materia. Dirt and grass, which are the most prevaent surfaces under home payground equipment, do not adequatey protect chidren from serious head injuries. Insta protective surfacing at east six feet in a directions from pay equipment. For swings, the surface shoud extend, in back and front, twice the height of the suspending bar. You shoud consut a oca contractor about ways to secure the product in your ocation. Do not insta your pay set over hard surface, e.g. asphat, concrete, packed earth, tie or brick foor. Pease refer to the CONSUMER PRODUCT SAFETY COMMISSION S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK for detaied guideines to prevent injuries from fas and other hazards on pubic and home paygrounds. SELECT PROTECTIVE SURFACING: One of the most important things you can do to reduce the ikeihood of serious head injury s is to insta shock-absorbing protective surfacing under and around your pay equipment. The Protective surfacing shoud be appied to a depth that is suitabe for the equipment height in accordance with ASTM F1292. NOTE: DO NOT insta home payground equipment over concrete, asphat, or any other hard surface. A Fa onto a hard surface can resut in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and environmenta factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are generay not adequate protective surfacing. Ground Leve equipment such as Sand-Box, activity wa, payhouse or other equipment that has no eevated pay surface does not need any protective surfacing. WARNINGS ON ANCHORING It is highy recommended the product be anchored into the ground to prevent movement and to make the swing set more stabe during use. Some consumers want an anchoring system that aows the product to be moved to different ocations. Other consumers want to keep their swing set in a permanent ocation. It is highy recommended that you seek the opinion from a oca icensed contractor on the best way to secure the swing set in your ocation. The best way to anchor a product is to create a concrete footing and use that as a base for an anchor. Whatever method you prefer for your ocation, an anchoring system for this product shoud be used at a times. 2

4 WEATHER CONDITIONS DO NOT use this equipment if the swing seat, side or any parts are wet. Use the pay set ony when the parts are cean and dry. If the equipment is wet, the user coud sip and suffer injuries. Pease be aware of weather conditions when using the equipment. If it is too windy, users coud ose contro and suffer injuries. The payground equipment must be propery anchored, stored away or restricted from use during incement weather such as heavy winds or severe weather storms. You shoud consut a oca contractor about ways to anchor the product in your ocation. WARNING STATEMENTS Observing the foowing statements and warnings reduces the ikeihood of serious or fata injury. DO NOT aow more than one chid to pay on the individua swing or side component at any one time. DO NOT aow chidren to stand on the side, swing seats or gide ride. The gide ride is made for ony two users at a time. DO NOT aow chidren to wak too cose to moving parts. ALWAYS keep a safe distance to avoid being struck by other chidren whie paying on swings, sides, trapeze, and gide ride etc. DO NOT aow chidren to hang upside down on trapeze bar! DO NOT aow chidren to twist the swing chains or oop them over the top support bar as this may reduce the strength of the chain. DO NOT swing empty seats as this may cause injuries. Chidren shoud not wak cose to, in front of, behind, or between moving items. DO NOT CLIMB on the Equipment when the Equipment is wet. DO NOT attached items to the equipment that are not specificay designed for use with the equipment, such as, but not imited to, Jump Ropes, Cothesine, pet eashes, cabes, and chain as they may cause a stranguation hazard. Dress Chidren with we-fitting and fu foot encosing footwear. Exampes of in-appropriate footwear are: CLOGS, fip fops, and sandas. ALWAYS guide chidren to sit in the center of swinging parts, with their fu weight paced in the seat center and hoding on to the swing chains. DO NOT aow chidren to jump off the equipment whie it is in motion. ALWAYS come to a fu stop before dismounting. ALWAYS dress chidren appropriatey for proper pay, e.g. wear we-fitted rubber soe shoes, and remove oose or sharp items such as jewery, hair accessories, scarves which may become entanged in the equipment or cause injuries. ALWAYS make sure chidren remove their bike or other sports hemets before paying on the payground. DO NOT aow chidren to side down the side head first. DO NOT aow chidren to cimb onto swing or jump to/from different pay areas of the equipment. ALWAYS return safey to the ground before approaching another pay area. DO NOT aow chidren to cimb on structura parts (e.g. egs, top bar). These are structura components and are not designed for pay. ALWAYS check the side or other parts exposed to the body for extreme heat from the sun before aowing chidren to use the equipment. ALWAYS prevent access and secure from any unauthorized use when there is no adut supervision. DO NOT aow pets or other animas near the equipment to prevent damage or injuries. Adequate overhead cearance is essentia. A minimum of 24 ft (7.3 meters) from ground eve is recommended. Provide cearance for wires, tree imbs, and other possibe hazards. Use the swing set in a we-it area. Artificia iumination may be required for shady areas. 3

5 INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION DO NOT use the equipment if any bots or nuts are missing or oose. ALWAYS check to ensure the equipment and a parts are we secured and stabe before each use. ALWAYS cear the pay area of any rocks, sharp objects, or any materias that coud be potentiay hazardous to users. DO NOT attach items to the equipment that are not specificay designed for use with the equipment, incuding, but not imited to, jump ropes, cothesine, pet eashes, cabes and chains as they may cause choke hazards. The stee and pastic parts used in your product are subject to norma wear. Gradua deterioration of the materia wi occur, the speed of which wi depend on the eve of exposure to UV rays, airborne poution, outdoor weather conditions such as rain and wind and the amount of use. You must inspect the equipment prior to every use. This incudes, but is not imited to inspecting the set for cracks, excess wear, missing parts, oose connections, and for overa integrity. When the set shows any signs of weakness, you must stop using the pay set immediatey, propery store the set or restrict access by users unti the condition is resoved. Verify that the chains are secured at both ends and tightened, so that there is no oose chain hanging that can resut in choking hazard. When conducting inspections, it is recommended that you use the Suggested Genera Maintenance Checkist and Routine Inspection and Maintenance Issues checkists provided by the US Consumer Product Safety Commission, a copy of which is contained in this user manua. CARE & MAINTENANCE INSTRUCTIONS Inspect a nuts and bots twice monthy during the usage season for tightness and tighten as required. It is particuary important that this procedure is foowed at the beginning of each season. Oi a metaic moving parts monthy during the usage period. Sand rusted areas on meta tubing and repaint using a nonead-based paint meeting the requirements of Tite 16 CFR Part Check swing seats and chains monthy during usage season for deterioration. Repacements shoud be made in accordance with the manufacturer s instructions. Check a coverings for bots and sharp edges twice monthy during usage season to be certain that they are in pace and repace when necessary. It is especiay important to do this at the beginning of each new season. Do not use when the temperature drops beow 32 degrees F (0 degrees C); remove and store the pastic swing seats and side indoors. 4

6 ANCHORING (NOTE:ANCHORS ARE NOT INCLUDED-MUST BE PURCHASED SEPARATELY) There are different ways of anchoring the equipment, depending on the type of ground on which the equipment is to be instaed. Make sure that a anchors are beow ground eve to prevent tripping. You shoud consut your oca contractor to decide the most appropriate way to anchor the equipment in your ocation. The foowing anchoring options may be considered: Corkscrew Anchoring (Corkscrew Anchors not incuded) If your soi is hard (cay, etc.), the corkscrew method may be suitabe. Be sure that the swing set is ocated on eve ground. Twist the corkscrew anchor into the ground unti ony the end with the hook is above the ground and next to the eg. Insert the hook into the bottom opening of the eg. Ensure that the hook is secured onto the eg opening. Concrete Anchoring (Materias not incuded) If the swing set is set up on grounds with sandy soi (soft) condition, it must be anchored with concrete footing (concrete not incuded) Be sure that the swing set is assembed and paced on eve ground Dig hoes around swing eg tube, as shown in drawing in the next page. As you dig deeper, enarge the diameter of the hoe to fix the cement Pace 2 inches of brick or grave underneath the eg, as shown in drawing in the next page Use about 45 bs. of concrete per eg Cover the concrete with dirt and protective surface materia Aow 6-7 days for the concrete to dry propery 5

7 FRAME LEG 12-5/8 CONCRETE 5 2 BRICK OR GRAVEL BED Note: The maximum fa height for this product is 4 feet. The minimum ground cearance between the bottom of the suspended pays and the paying or ground surface must be 8 inches. You must maintain a minimum of 8 inches of ground cearance. 8 WARNING Pease propery anchor the swing set to minimize the risk of injury or death. If the swing set is used without proper anchoring, it may be dangerous and may tit over. 6

8 CARE AND MAINTENANCE CHECKLIST AT THE BEGINNING OF EACH PLAY SEASON: n Tighten a hardware. n Lubricate a metaic moving parts per manufacturer s instructions. n Check a protective coverings on bots, pipes, edges, and corners. Repace if they are oose, cracked, or missing. n Check a moving parts incuding swing seats and chains for wear, rust or other deterioration. Repace as needed. n Check meta parts for rust. If found, sand and repaint using a non-ead paint meeting the requirements of 16 CFR n Reinsta any pastic parts, such as swing seats or any other items that were removed for the cod season. n Rake and check depth of oose fi protective surfacing materias to prevent compaction and to maintain appropriate depth. Repace as needed. TWICE A MONTH DURING PLAY SEASON: n Tighten a hardware. n Check a protective coverings on bots, pipes, edges and corners. Repace if they are oose, cracked or missing. n Rake and check depth of oose fi protective surfacing materias to prevent compaction and to maintain appropriate depth. Repace as needed. ONCE A MONTH DURING PLAY SEASON: n Lubricate a metaic moving parts per manufacturer s instructions. n Check a moving parts incuding swing seats and chains for wear, rust or other deterioration. Repace as needed. n Rake and check depth of oose fi protective surfacing materias to prevent compaction and to maintain appropriate depth. Repace as needed. AT THE END OF EACH PLAY SEASON: n At the end of each pay season or when the temperature drops beow 32 degrees F (0 degrees C). n Remove pastic swing seats and other items as specified by the manufacturer and take indoors or do not use. n Rake and check depth of oose fi protective surfacing materias to prevent compaction and to maintain appropriate depth. Repace as needed. As a genera rue, maintenance shoud be performed at any time it is deemed necessary. DISPOSAL INSTRUCTIONS u Pease use care when disassembing the equipment, when it is no onger in operationa condition. Wear heavy duty working goves to avoid injuries. u Fuy disassembe the entire swing and side sets before disposa. Do not eave partiay disassembed parts in areas accessibe by chidren. u Shoud you wish to recyce the stee tubing, pease take the frame to your oca recycing center. u A pastic parts can be recyced, take it to your oca recycing center. Do not et chidren pay with any disassembed parts meant for disposa, such as chains, side, tubing, bots, nuts, screws, etc. u A rusted parts, bots must be propery disposed of in trash bin. Do not reuse. Owners sha be responsibe for maintaining the egibiity of the warning abes. 7

9 TOOLS NEEDED Pease prepare the foowing toos prior to assembing this equipment. Specia Socket Wrench (Incuded) Tape Measure (Not incuded) Hammer (If you intend to insta anchor, this is needed) Wrench (Incuded) Wrench (Not Incuded) Big Aen Wrench (Incuded) Fat Head and Phiips Head Screwdriver (Not incuded) Medium Aen Wrench (Incuded) Sma Aen Wrench (Not Incuded) 8

10 Part ist for main frame assemby A1 LEFT TOP BAR 1 A2 MIDDLE TOP BAR 1 A3 RIGHT TOP BAR 1 A4 TOP SECTION LEG 4 A5 BOTTOM SECTION LEG WITH FOAM 4 A6 CROSS BAR (WITH TWO HOLES) 1 A7 CROSS BAR (WITH FOUR HOLES) 1 Hardware used for main frame assemby B1 BOLT 5/16"x2-1/2" 12 B2 BOLT 5/16"x2-3/4" 4 B3 NYLON NUT 5/16" 16 B4 PLASTIC CAP (WITH ARC WASHER) 16 B5 ARC WASHER 5/16" 12 B6 WASHER 5/16" 4 Bracket used for gide ride assemby L3 BRACKET 1 L4 BRACKET CLAMP 1 L5 REINFORCING STEEL SPACER 2 N3R BOLT 5/16"x1" 2 N7 NYLON NUT 5/16" 2 9

11 Part ist for gide ride assemby L1-N TOP SECTION HANGER 2 L2-N BOTTOM SECTION HANGER 2 L3-N GLIDE SEAT SUPPORT 2 M1 TUBE CAP(PRE-ASSEMBLED) 2 M2 M3 SMALL NYLON BEARING (PRE-ASSEMBLED) LARGE NYLON BEARING (PRE-ASSEMBLED) 2 4 M4 GLIDE SEAT 2 M5 FOOTREST 2 Hardware used for gide ride assemby N1 BOLT 1/4"x1-1/2" 4 N2R BOLT 1/4"x1-3/4" 2 N4 SCREW 0.22"x3/4" 4 N5 J-BOLT 2 N6 SPRING WASHER (sma) 8 N8 CAP BOLT 1/4"x1/2" 2 N9 CAP NUT 1/4" 8 N10 NUT 1/4" 2 N11 SPRING WASHER (arge) 2 N12 SPRING WASHER (medium) 4 N13 BOLT 1/4 x1-3/8" 4 N14 ARC WASHER5/16" 8 10

12 Part ist for swing seat assemby J1 J3 PVC COVERED CHAIN (PRE-ASSEMBLED) EYE BOLT WITH ATTACHMENT BOLT (PRE-ASSEMBLED) 4 8 K1 SWING SEAT 2 Hardware used for swing seat assemby J6 NYLON NUT 5/16" 8 J7 WASHER5/16" 4 J8 PLASTIC CAP (WITH ARC WASHER) 4 J9 PLASTIC CAP (WITH FLAT WASHER) 4 Part ist for trapeze assemby P1 TRAPEZE 1 T3 RUBBER CAP (PRE-ASSEMBLED) 2 S1 EYEBOLT WITH CHAIN (PRE-ASSEMBLED TO TRAPEZE) 2 Hardware used for trapeze assemby S3 PLASTIC CAP (WITH ARC WASHER) 2 P4 NYLON NUT 5/16" 2 11

13 Part ist for side assemby X1-N SLIDE SUPPORT (WITH OPENING) 1 X2-N SLIDE SUPPORT 1 X3-N SLIDE LEG TUBE 2 X4-N SLIDE TOP SUPPORT BAR 1 X5-N SLIDE FRONT SUPPORT 1 X6 SLIDE LADDER STEPS 2 Y2 SLIDE 1 Hardware used for side assemby Y1 PLASTIC CONNECTOR 2 Z1 BOLT 1/4"x1-1/2" 6 Z2 BOLT 1/4"x4-1/2" 2 Z3 SPRING WASHER 4 Z4 CAP NUT 1/4" 10 Z5 CAP BOLT 1/4"x1/2" 4 Z6 SPRING WASHER (sma) 20 Z7 BOLT 1/4"x3" 2 Z8 BOLT 1/4"x2-1/4" 4 12

14 ASSEMBLY INSTRUCTIONS Ø Pace the payground equipment on eve ground and not ess than 6ft (1.8m) from any structure or obstruction such as a fence, garage, house, overhanging branches, aundry ine, or eectrica wires. Ø Do not insta the payground equipment over concrete, asphat, packed earth, or any other hard surface; a fa onto a hard surface can resut in serious injury or death to the equipment user. Ø Adequate overhead cearance is essentia. A minimum cearance from ground eve sha be recommended. Provide cearance for wires, tree imbs, and other possibe hazards. Ø Use the swing set in a we-ighted area. Artificia iumination may be required for shady areas. Ø Secure the swing set against unauthorized and unsupervised use. Ø The owner and supervisors of the swing set are responsibe to make a users aware of practices specified in the use instructions. TIGHTENING NUTS & BOLTS Ø For ease of instaation, do not over-tighten the nuts and bots when you are first putting the equipment together. some possibe adjustments during instaation. This wi aow for Ø Once you have finished assembing each component of the pay set, make sure to go back over each step and propery tighten a nuts, bots and pastic caps. Check the entire unit to ensure a parts are propery assembed before aowing chidren to use the payground equipment. 13

15 STEP 1 Assembe the top bar frame of the swing set Ø Connect A1, A2 and A3 secure with B1, B3, B4 and B5 as shown beow. Note: A round hoes shoud be facing up and concave hoes facing down. B3 B3 B4 B4 A1 B5 A2 B5 A3 B1 B1 14

16 STEP 2 Assembe the support egs of swing set Ø Connect A1 to A4 and secure using B1, B5, B4 and B3 as shown beow. Ø Repeat the above step for the right side of the swing set (A3 and A4, A5). A1 B1 B5 B5 B1 A4 A4 B3 B4 A5 A5 15

17 STEP 3 Assembe the support egs of swing set Ø Connect A4 to A5 and secure using B1, B5, B4 and B3 as shown beow. Ø Repeat the above step for the right side of the swing set (A3 and A4, A5). A4 A4 B1 B5 B4 B3 A5 B4 B3 B5 B1 A5 16

18 STEP 4 Attach the crossbar to the support egs. Ø Attach A6 to the outer side of A5 and secure using B2, B6, B4 and B3. A1 A4 A4 B2 B6 B3 B4 A5 A6 B3 B4 B2 B6 A5 17

19 Ø Attach A7 to the outer side of A5 and secure using B2, B6, B4 and B3. A3 A4 A4 B3 B4 B6 B2 B3 B4 A7 A5 A5 B6 B2 18

20 STEP 5 - Gide Ride assemby Ø Attach L4 and L3 to A3 using N3R, L5 and N7 as shown. Use specia socket wrench and screw driver to tighten N3R and N7. N3R L4 A3 L3 L5 L5 N7 N7 USE SPECIAL SOCKET WRENCH AND SCREW DRIVER TO TIGHTEN N7. 19

21 STEP 6 Gide ride assemby (continued) Ø Insert L1-N (straight end) into L2-N and secure with N14,N6,N9 and N13 on both sides. Ø Repeat the above steps on the other side N9 N6 L1-N N14 N14 N13 L2-N 20

22 STEP 7 Gide ride assemby (continued) Ø Insert L2-N (straight end) into M5 and secure with N4 and N12 on both sides. Ø Attach M1 to the top of L1-N (curved end). Aign hoes and insert M2. Ø Attach L1-N to L3 on both sides and secure with N2R and N10. N10 L3 N10 M1 N2R N2R L1-N L1-N M2 L2-N L2-N N4 N12 L2-N M5 N12 N4 21

23 STEP 8 Gide ride assemby (continued) Ø Attach L3-N to L2-N on both sides and secure with N5, M3, N11 and N8. Concave hoes face up L1-N L2-N N5 Round hoes M3 N11 N8 face down N11 M3 N8 L3-N N5 22

24 STEP 9 Gide ride assemby (continued) Ø Attach M4 to L3-N and secure with N1, N6 and N9. N1 L1-N M4 L2-N L3-N N1 N6 L3-N M4 N9 M5 N6 N9 23

25 STEP 10 - Swing Seat assemby Ø Connect swing set chains to the top bar by inserting J3 through A1, A3 and securing with J8 and J6 as shown in Diagram A. Ø Connect swing seat to the chains by inserting J3 through K1 and secure with J7, J9 and J6 as shown in Diagram B. Ø Repeat the above steps to assembe A3 in the same manner as A1. J6 J8 DIAGRAM A J8 J6 A1 or A3 J3 J3 J1 J1 J3 DIAGRAM B J3 J1 J1 J3 J3 K1 J7 J6 J9 J6 J7 J9 24

26 STEP 11 - Trapeze Assemby Ø Insert S1 (which is pre-assembed with P1) through the hoe on A2. Ø Secure using S3 and P4 as shown in the diagram beow. P4 P4 S3 A2 S3 S1 S1 P1 NOTE: 1. Do not over-tighten the nuts and bots at every step. 2. Do not snap in the cover of pastic cap unti you have finished the assemby of each step and went back to tighten a of the nuts and bots. 25

27 Side assemby STEP 12 - Side assemby Ø Insert X5-N into the base of Y2. Ø Secure using Z8, Z6 and Z4. Ø Attach X4-N to Y2. Ø Note: Make sure that the bot hoes face up. Y2 X4-N Z6 Z8 Bot hoe faces up. Z4 Z6 X5-N Z8 NOTE: 1.Do not over-tighten the nuts and bots at every step. 2.Do not snap in the cover of pastic cap unti you have finished the assemby of each step and went back to tighten a of the nuts and bots. 26

28 STEP 13 - Side assemby (continued) Ø Attach X6 to X1-N and X2-N. Ø Secure each side using Z1, Z6 and Z4. Ø Attach X3-N to X1-N and X2-N. Ø Aign hoes and hod in position. Narrow side (Direction as shown beow) X2-N Wide side faces the front direction of the side X1-N Z4 Z6 Z1 X6 Z6 X3-N Z4 Z1 Z6 Z6 X3-N NOTE: 1.Do not over-tighten the nuts and bots at every step. 2.Do not snap in the cover of pastic cap unti you have finished the assemby of each step and went back to tighten a of the nuts and bots. 27

29 STEP 14 - Side assemby (continued) Ø Secure the two sides of the side using Z2, Z6 and Z4, in the sequence shown in the diagram. Ø Attach X4-N to X1-N and X2-N; Secure using Z1, Z6, Z3 and Z5 as shown in the enarged diagram. X4-N X2-N Z1 X1-N Z6 Z2 Z6 Z3 Z4 Z5 Z6 Y2 X1-N Z2 Z6 X3-N NOTE: 1.Do not over-tighten the nuts and bots at every step. 2.Do not snap in the cover of pastic cap unti you have finished the assemby of each step and went back to tighten a of the nuts and bots. 28

30 STEP 15 - Side assemby (continued) Ø Fit Y1 in between X1-N and A6; Secure using Y1, Z7, Z6 and Z3, Z5 A3 X1-N Z5 Z3 Y1 Z3 Z5 Z7 Z6 A6 A5 A5 NOTE: 1.Do not over-tighten the nuts and bots at every step. 2.Do not snap in the cover of pastic cap unti you have finished the assemby of each step and went back to tighten a of the nuts and bots. 29

31 Congratuations! You have now competed the swing set assemby. Pease make sure to thoroughy check a parts and hardware to make sure a bots and nuts are we secured before using the payground equipment. WARNING - Do not et chidren use the payground equipment unti it is propery assembed and anchored. 30

32 Dear Customer: Thank you for your purchase of an XDP Recreation swing set. By foowing the instruction manua, reading a safety and assemby instructions, and propery anchoring your swing set in the ground, your kids wi safey enjoy hours of fun. Detaied beow is our warranty covering your purchase. Pease be sure to read it and contact us in the event you need service or parts. DO NOT RETURN THE SET TO THE STORE YOU PURCHASED IT. Sincerey, XDP Recreation LLC MANUFACTURER'S LIMITED WARANTY What does this Limited Warranty cover? This warranty covers your XDP Recreation product for one hundred and eight (180) days against defects in materia, workmanship, and rust on painted parts which compromise the structura integrity of the product when used for the purpose intended, norma outdoor conditions, and provided it is assembed correcty as iustrated in this manua and receives the proper care and maintenance. NOTE: Surface rust is not covered under this warranty. Who does this Limited Warranty Cover? This warranty is extended ony to the origina purchaser with a receipt and is not transferrabe. What wi XDP Recreation do? They wi provide a repacement part at no charge for any part found defective during the warranty period. What does this warranty NOT cover? This imited warranty does not cover XDP Recreation products which: fai due to (1) norma wear; (2) abuse and misuse; (3) improper maintenance; (4) unauthorized repairs or incorrect parts use; or (5) are used for commercia or other income producing purposes. How do you obtain service? A warranty repairs must be authorized by XDP Recreation Customer Service Assistance Department before repairs are made. IMPORTANT: There is NO NEED to return the entire unit to the store where it was purchased! In order to obtain quick service provided by this warranty, you may ca or emai the detais using the beow contact: Customer Support: 8:00 AM to 5:00 PM Monday through Friday (Eastern Standard Time) Or emai us at service@xdp-recreation.com or via fax at Further info can be found at REGISTER YOUR PURCHASE PLEASE VISIT OUR WEBSITE at to register your purchase using the manufacturer date code found on the abe on the swing set. There aso is a short on-ine survey which you can fi out to compete the registration. 31