DATA SHEET LC-D CONTACTORS

Transcription

1 Issued November 2009 DATA SHEET LC-D CONTACTORS Based on Shneider MKTED205103EN Catalogue

2 Charateristis 5 d Contator type LC1 D09 D18 D25 D38 D40 D50 D95 D115 and D150 DT20 and DT25 DT32 and DT40 Environment Rated insulation voltage (Ui) Conforming to IEC , V overvoltage ategory III, degree of pollution: 3 Conforming to UL, CSA V 600 Rated impulse withstand voltage (Uimp) Conforming to IEC kv 6 8 Conforming to standards IEC , , NFC , VDE 0660, BS 5424, JEM EN , EN GL, DNV, PTB, RINA Produt ertifiations UL, CSA Complies with SNCF, Sihere Trennung reommendations Separation insulation Conforming to VDE 0106 part 101 and (draft 2/89) V 400 Degree of protetion (1) (front fae only) Conforming to VDE 0106 and IEC Power onnetion Coil onnetion Protetion against diret finger ontat IP 2X Protetion against diret finger ontat IP 2X Protetive treatment Conforming to IEC TH Ambient air temperature around the devie Storage C Operation C Permissible C , for operation at U Maximum operating altitude Without derating m 3000 Operating positions (2) Without derating in the following positions a/ a Positions that are not permissible For ontators LC1 D09 to D38 Flame resistane Conforming to UL 94 V1 Conforming to IEC C 960 Shok resistane (3) 1/2 sine wave = 11 ms Vibration resistane (3) Hz Contator open 10 gn 8 gn 8 gn 8 gn 6 gn Contator losed 15 gn 15 gn 10 gn 10 gn 15 gn Contator open 2 gn Contator losed 4 gn 4 gn 4 gn 3 gn 4 gn (1) Protetion provided for the abling.s.a.'s indiated on the next page and for onnetion by able. (2) For other operating positions, please onsult your Regional Sales Offie. (3) Without hange of ontat states, in the most unfavourable diretion (oil energised at Ue). Based on Shneider MKTED205103EN Catalogue Page 1 of 44

3 Charateristis (ontinued) 5 d Contator type LC1 D09 and D12 DT20 and DT25 D18 (3P) D25 (3P) D32 D38 D18 and D25 (4P) DT32 and DT40 Power iruit onnetions Connetion by able Tightening torque Srew lamp terminals Connetor 2 inputs Flexible able without able end Flexible able with able end Solid able without able end D40 Srew lamp terminals D50 and D65 Connetor 1 input D80 and D95 D115 and D150 Connetor 2 inputs 1 ondutor mm ondutors mm ondutor mm ondutors mm ondutor mm ondutors mm Srewdriver Philips N 2 N 2 N 2 N 2 N 2 Flat srewdriver Ø Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Ø 8 Ø 6 Ø 8 Ø 6 Ø 8 Key for hexagonal headed srew 4 4 Tightening torque N.m Spring terminal onnetions (1) Flexible able without able end 1 ondutor mm (4: DT25) 2 ondutors mm (exept DT25) Connetion by bars or lugs Bar ross-setion 3 x 16 5 x 25 Lug external Ø mm (2) Ø of srew mm M3.5 M3.5 M4 M4 M3.5 M5 M6 M6 M8 Srewdriver Philips N 2 N 2 N 2 N 2 N 2 N 2 N 3 Flat srewdriver Ø Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Ø 8 Ø 8 Ø 8 Key for hexagonal headed srew Tightening torque N.m Control iruit onnetions Connetion via able (tightening via srew lamps) Flexible able without able end Flexible able with able end Solid able without able end 1 ondutor mm ondutors mm ondutor mm ondutors mm ondutor mm ondutors mm Srewdriver Philips N 2 N 2 N 2 N 2 N 2 N 2 N 2 N 2 N 2 Flat srewdriver Ø Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Tightening torque N.m Spring terminal onnetions (1) Flexible able 1 ondutor mm without able end 2 ondutors mm Connetion by bars or lugs Lug external Ø mm Ø of srew mm M3.5 M3.5 M3.5 M3.5 M3.5 M3.5 M3.5 M3.5 M3.5 Srewdriver Philips N 2 N 2 N 2 N 2 N 2 N 2 N 2 N 2 N 2 Flat srewdriver Ø Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Ø 6 Tightening torque N.m (1) If able ends are used, hoose the next size down (example: for 2.5 mm 2, use 1.5 mm 2 ) and square rimp the able ends using a speial tool. (2) To onnet ables with a.s.a. > 4mm 2 and up to 10 mm 2, it is essential to use speial onnetors, sold in bags of 100 (referene: LAD 96180). Based on Shneider MKTED205103EN Catalogue Page 2 of 44

4 Charateristis (ontinued) 5 d Contator type LC1 D09 (3P) Pole harateristis Rated operational urrent (Ie) (Ue y 440 V) DT20 D098 D12 (3P) DT25 D128 D18 (3P) DT32 D188 In AC-3, θ y 60 C A In AC-1, θ y 60 C A 25 (1) (1) (1) (1) 40 Rated operational voltage (Ue) Up to V Frequeny limits Of the operating urrent Hz Conventional thermal urrent θ y 60 C A 25 (1) (1) (1) (1) 40 (Ith) Rated making apaity Conforming to IEC (440 V) Rated breaking apaity (440 V) Conforming to IEC Permissible short time rating No urrent flowing for preeding 15 minutes with θ y 40 C Protetion by fuses against short-iruits (U y 690 V) For 1 s A For 10 s A For 1 min A For 10 min A Without thermal overload relay, gg fuse type 1 A type 2 A With thermal overload relay A See pages 6/16 and 6/17, for am or gg fuse ratings orresponding to the assoiated thermal overload relay Average impedane per pole At Ith and 50 Hz mω Power dissipation per pole for the above operational urrents Control iruit harateristis, a.. supply AC-3 W AC-1 W Rated ontrol iruit voltage 50/60 Hz V (U) Control voltage limits 50 or 60 Hz oils Operational Drop-out 50/60 Hz oils Operational U on 50 Hz and U on 60 Hz at 60 C Drop-out U at 60 C Average onsumption at 20 C and at U a 50 Hz Inrush 50 Hz oil VA Cos ϕ /60 Hz oil VA 70 Sealed 50 Hz oil VA Cos ϕ /60 Hz oil VA 7 a 60 Hz Inrush 60 Hz oil VA Cos ϕ /60 Hz oil VA 70 Sealed 60 Hz oil VA Cos ϕ /60 Hz oil VA 7.5 Heat dissipation 50/60 Hz W 2 3 Operating time (2) Mehanial durability in millions of operating yles Closing "C" ms Opening "O" ms or 60 Hz oil 50/60 Hz oil on 50 Hz 15 D25 (3P) DT40 D258 Maximum operating rate at ambient temperature y 60 C In operating yles per hour 3600 (1) Versions with spring terminal onnetions: 16 A for LC1 D093 and LC1 D123 (20 A possible with 2 x 2.5 mm 2 ables in parallel), 25 A for LC1 D183 to LC1 D323 (32 A possible for LC1 D183 onneted with 2 x 4 mm2 ables in parallel; 40 A possible for LC1 D253 and LC1 D323 onneted with 2 x 4 mm2 ables in parallel). (2) The losing time "C" is measured from the moment the oil supply is swithed on to initial ontat of the main poles. The opening time "O" is measured from the moment the oil supply is swithed off to the moment the main poles separate. Based on Shneider MKTED205103EN Catalogue Page 3 of 44

5 5 5 D32 D38 D40 D50 D65 D80 D95 D115 D (1) See pages 24514/2 and 24514/3, for am or gg fuse ratings orresponding to the assoiated thermal overload relay U at 55 C U at 55 C U at 55 C U at 55 C U on 50 Hz and U on 60 Hz at 60 C U on 50 Hz and U on 60 Hz at 55 C U on 50/60 Hz at 55 C U at 60 C U at 55 C U at 55 C Based on Shneider MKTED205103EN Catalogue Page 4 of 44

6 Charateristis (ontinued) 5 d Contator type d.. ontrol iruit harateristis LC1 D09 D38 LC1 DT20 DT40 LC1 or LP1 D40 D65 LC1 or LP1 D80 LC1 D95 LC1 D115 and LC1 D150 Rated ontrol V iruit voltage (U) Rated insulation voltage Conforming to IEC V 690 Conforming to UL, CSA V 600 Control voltage limits Operational Standard oil Wide range oil Average onsumption at 20 C and at U Average operating time at U (1) U at 60 C U at 55 C U at 55 C U at 55 C Drop-out U at 60 C U at 55 C U at 55 C Inrush W to 365 Sealed W Closing "C" ms 63 ± 15 % Opening "O" ms 20 ± 20 % Nota : The aring time depends on the iruit swithed by the poles. For all normal 3-phase appliations, the aring time is less than 10 ms. The load is isolated from the supply after a time equal to the sum of the opening time and the aring time. Time onstant L/R (L/R) ms Mehanial durability at U In millions of operating yles Maximum operating rate at ambient temperature y 60 C In operating yles per hour Low onsumption ontrol iruit harateristis Rated insulation voltage Conforming to IEC V 690 Conforming to UL, CSA V 600 Maximum voltage Of the ontrol iruit on 250 Average onsumption d.. at 20 C and at U Operating time (1) at U and at 20 C Wide range oil ( U) Inrush W 2.4 Sealed W 2.4 Closing "C" ms 77 ± 15 % Opening "O" ms 25 ± 20% Voltage limits (θ y 60 C) of the ontrol iruit Operational 0.7 to 1.25 U Drop-out U Time onstant L/R (L/R) ms 40 Mehanial durability In millions of operating yles 30 Maximum operating rate At ambient temperature y 60 C ops/h 3600 (1) The operating times depend on the type of ontator eletromagnet and its ontrol mode. The losing time "C" is measured from the moment the oil supply is swithed on to initial ontat of the main poles. The opening time "O" is measured from the moment the oil supply is swithed off to the moment the main poles separate. Based on Shneider MKTED205103EN Catalogue Page 5 of 44

7 Charateristis (ontinued) 5 d Charateristis of auxiliary ontats inorporated in the ontator Mehanially linked ontats Mirror ontat Conforming to IEC Conforming to IEC Rated operational voltage (Ue) Up to V 690 Rated insulation voltage (Ui) Conforming to IEC V 690 Conforming to UL, CSA V 600 Conventional thermal urrent (Ith) Frequeny of the operational urrent For ambient temperature y 60 C A 10 Eah ontator has 2 N/O and N/C ontats mehanially linked on the same movable ontat holder The N/C ontat on eah ontator represents the state of the power ontats and an be onneted to a PREVENTA safety module Hz Minimum swithing apaity U min V 17 λ = 10 8 I min ma 5 Short-iruit protetion Conforming to gg fuse: 10 A IEC Rated making apaity Conforming to IEC , I rms A a: 140, : 250 Short-time rating Permissible for 1 s A ms A ms A 140 Insulation resistane MΩ > 10 Non-overlap time Operational power of ontats onforming to IEC Guaranteed between N/C and N/O ontats ms 1.5 on energisation and on de-energisation a.. supply, ategories AC-14 and AC-15 d.. supply, ategory DC-13 Eletrial durability (valid for up to 3600 operating yles/hour) Eletrial durability (valid for up to 1200 operating yles/hour) on an indutive load suh as the oil of an eletromagnet: on an indutive load suh as the oil of an eletromagnet, making urrent (os ϕ 0.7) = 10 times the power broken without eonomy resistor, the time onstant inreasing with the (os ϕ 0.4). load. V V million operating yles VA W million operating yles VA W million operating yles VA W AC-15 DC-13 Millions of operating yles ,8 0,7 0,6 0,5 0,4 0,3 Millions of operating yles ,8 0,7 0,6 0,5 0,4 0,3 440 V 250 V 125 V 48 V 24 V 0,2 0,2 0,1 0,1 0,2 0,3 0,4 0,6 0, ,5 0,7 0, Current broken in A 0,1 0,1 0,2 0,3 0,4 0,6 0, ,5 0,7 0, Current broken in A Based on Shneider MKTED205103EN Catalogue Page 6 of 44

8 Charateristis 5 Auxiliary ontat bloks without dust and damp proteted ontats for d ontators Contat blok type LAD N or LAD C LAD T and LAD S LAD R LAD 8 Environment Conforming to standards IEC , NF C , VDE 0660, BS 4794, EN Produt ertifiations UL, CSA Protetive treatment Conforming to IEC TH Degree of protetion Conforming to VDE 0106 Protetion against diret finger ontat IP 2X Ambient air temperature around the devie Storage C Operation C Permissible for operation at U C Maximum operating altitude Without derating m 3000 Connetion by able Spring terminal onnetions Phillips N 2 and Ø 6 mm Flexible or solid able with or without able end Flexible or solid able without able end mm 2 Min: 1 x 1, max: 2 x 2.5 mm 2 Max. 2 x 2.5 Instantaneous and time delay ontat harateristis Number of ontats 1, 2 or Rated operational voltage Up to V 690 (Ue) Rated insulation voltage (Ui) Conforming to IEC V 690 Conforming to UL, CSA V 600 Conventional thermal For ambient temperature y 60 C A 10 urrent (Ith) Frequeny of the Hz operational urrent Minimum swithing apaity U min V 17 I min ma 5 Short-iruit protetion Conforming to IEC and VDE gg fuse A 10 Rated making apaity Conforming to I rms A a: 140 ; : 250 IEC Short-time rating Permissible for 1 s A ms A ms A 140 Insulation resistane MΩ > 10 Non-overlap time Guaranteed between N/C and N/O ontats ms 1.5 (on energisation and on de-energisation) Overlap time Guaranteed between N/C and ms 1.5 N/O ontats on LAD C22 Time delay Ambient air temperature for C (LAD T, R and S ontat bloks) operation Auray only valid for setting Repeat auray ± 2 % ± 2 % range indiated on the front fae Drift up to 0.5 million + 15 % + 15 % operating yles Drift depending on 0.25 % per C 0.25 % per C ambient air temperature Mehanial durability In millions of operating yles Operational power of ontats See page 9 Based on Shneider MKTED205103EN Catalogue Page 7 of 44

9 Charateristis (ontinued) 5 Auxiliary ontat bloks with dust and damp proteted ontats for d ontators Contat blok type L DX L DZ L DY Proteted Non proteted Environment Conforming to standards IEC , VDE 0660 Produt ertifiations UL, CSA Protetive treatment Conforming to IEC TH Degree of protetion Conforming to VDE 0106 Protetion against diret finger ontat IP 2X Ambient air temperature Storage and operation C Connetion Phillips N 2 and Ø 6 mm Flexible or solid able with or without able end mm 2 Min: 1 x 1, max: 2 x 2.5 Number of ontats Contat harateristis Rated operational voltage Up to V (Ue) Rated insulation voltage (Ui) Conforming to IEC V Conforming to UL, CSA V 600 Conventional thermal urrent (Ith) For ambient temperature y 40 C A 10 Maximum operational urrent ma (Ie) Frequeny of the Hz operational urrent Minimum swithing apaity U min V I min ma Short-iruit protetion Conforming to IEC A 10 gg fuse Rated making apaity Conforming to IEC , I rms A a: 140; : 250 Short-time rating Permissible for 1 s A ms A ms A 140 Insulation resistane MΩ > 10 > 10 > 10 > 10 Mehanial durability In millions of operating yles Materials and tehnology used for dust and damp proteted ontats Silver - Single break Silver - Single break Gold - Single break with rossed bars Based on Shneider MKTED205103EN Catalogue Page 8 of 44

10 Charateristis (ontinued) 5 Auxiliary ontat bloks with dust and damp proteted ontats for d ontators Rated operational power of ontats (onforming to IEC ) a.. supply, ategories AC-14 and AC-15 Eletrial durability (valid for up to 3600 operating yles/hour) on an indutive load suh as the oil of an eletromagnet: making urrent (os ϕ 0.7) = 10 times the power broken (os ϕ 0.4). V million operating yles VA million operating yles VA million operating yles VA Millions of operating yles ,8 0,7 0,6 0,5 0,4 0,3 0,2 0,1 0,1 0,2 0,3 0,4 0,6 0, ,5 0,7 0, Current broken in A d.. supply, ategory DC 13 Eletrial durability (valid for up to 1200 operating yles/hour) on an indutive load suh as the oil of an eletromagnet, without eonomy resistor, the time onstant inreasing with the load. V million operating yles W million operating yles W million operating yles W Millions of operating yles V 125 V 48 V 24 V 1 0,8 0,7 0,6 0,5 0,4 0,3 440 V 0,2 0,1 0,1 0,2 0,3 0,4 0,6 0, ,5 0,7 0, Current broken in A Based on Shneider MKTED205103EN Catalogue Page 9 of 44

11 Charateristis 5 Control modules, oil suppressor modules and mehanial lath bloks for d ontators Environment Conforming to standards IEC Produt ertifiations UL, CSA Protetive treatment Conforming to IEC TH Degree of protetion Conforming to VDE 0106 Protetion against diret finger ontat IP 2X Ambient air temperature around the devie Storage C Operation C Permissible for operation at U C Auto-Man-Stop ontrol modules Reommendation The Auto - Man seletor swith must only be operated with the Start - Stop ( O I ) swith in position O Rated insulation voltage Conforming to IEC V 250 Rated operational voltage Conforming to IEC V 250 Protetion Against eletri shoks kv 2 Built-in protetion Contator oil suppression By varistor Indiation By integral LED Illuminates when the ontator oil is energised Eletrial durability In operating yles Suppressor modules Module type LA4 DA, LAD 4RC LA4 DB, LAD 4T LA4 DC LA4 DE, LAD 4V Type of protetion RC iruit Bidiretional peak Diode Varistor limiting diode Rated ontrol iruit voltage (U) V a a or a or Maximum peak voltage 3 U 2 U U 2 U Natural RC frequeny 24/48 V Hz /127 V Hz /240 V Hz /415 V Hz 150 Mehanial lath bloks (1) Mehanial lath blok type LA6 DK10 LAD 6K10 LA6 DK20 For mounting on ontator LC1 D40 D65, LP1 D65 LC1 D09 D38, DT20 DT40 Produt ertifiations UL, CSA UL, CSA Rated insulation voltage Conforming to IEC V Rated ontrol iruit voltage a 50/60 Hz and V Power required For unlathing a VA W Maximum operating rate In operating yles/ hour On-load fator 10 % 10 % Mehanial durability at U In millions of operating yles LC1 D80 D150 LP1 D80 and LC1 D115 (1) Unlathing an be manually operated or eletrially ontrolled (pulsed). The LA6 DK or LAD 6K lath oil and the LC1 D operating oil must not be energised simultaneously. The duration of the LA6 DK or LAD 6K and LC1 D ontrol signals must be u 100 ms. Based on Shneider MKTED205103EN Catalogue Page 10 of 44

12 Charateristis 5 Eletroni serial timer module for d ontators Module type LA4 DT (On-delay) Environment Conforming to standards IEC Produt ertifiations UL, CSA Protetive treatment Conforming to IEC TH Degree of protetion Conforming to VDE 0106 Protetion against diret finger ontat IP 2X Ambient air temperature around the devie Storage C Operation C For operation at U C Rated insulation voltage (Ui) Conforming to IEC V 250 Cabling Phillips n 2 and Ø 6 mm Flexible or solid ondutor with or without able end mm 2 Min: 1 x 1, max: 2 x 2.5 Control iruit harateristis Built-in protetion On input By varistor Contator oil suppression By varistor Rated ontrol iruit voltage V a or (U) Permissible variation U Type of ontrol By mehanial ontat only Timing harateristis Timing ranges s 0.1 2; ; Repeat auray 0 40 C ± 3 % (10 ms minimum) Reset time During time delay period ms 150 After time delay period ms 50 Immunity to mirobreaks During time delay period ms 10 After time delay period ms 2 Minimum ontrol pulse duration ms Indiation of time delay By LED Illuminates during time delay period Swithing harateristis (solid state type) Maximum power dissipated W 2 Leakage urrent ma < 5 Residual voltage V 3.3 Overvoltage protetion 3 kv; 0.5 joule Eletrial durability In millions of operating yles 30 Funtion diagram LA4 DT On-delay eletroni timers U supply - Time delay output Contator oil Red LED t Based on Shneider MKTED205103EN Catalogue Page 11 of 44

13 Charateristis 5 Interfae modules for d ontators Environment Conforming to standards IEC Produt ertifiations UL, CSA Protetive treatment Conforming to IEC TH Degree of protetion Conforming to VDE 0106 Protetion against diret finger ontat IP 2X Ambient air temperature around the devie Storage C Operation C Permissible for operation at U C Other harateristis Module type LA4 DFBQ LA4 DFB LA4 DFE LA4 DLB LA4 DLE LA4 DWB With relay With relay With relay With relay + override Solid state Rated insulation voltage Conforming to V IEC Rated operational voltage Conforming to IEC V Indiation of input state By integral LED whih illuminates when the ontator oil is energised Input signals Control voltage (E1-E2) V Permissible variation V Current onsumption at 20 C ma for 5 V 15 for 24 V State 0 guaranteed for U V < 2.4 < 2.4 < 4.8 < 2.4 < 4.8 < 2.4 I ma < 2 < 2 < 1.3 < 2 < 1.3 < 2 State 1 guaranteed for U V Built-in protetion Against reverse polarity By diode Of the input By diode Eletrial durability In millions of operating yles at 220 A/240 V Maximum immunity ms to mirobreaks Power dissipated At 20 C W Diret mounting without ontator Mounting with abling adapter LAD 4BB Total operating time at U (of the ontator) Cabling With oil a V LC1 D40 D150 a V LC1 D40 D115 a V LC1 D40 D150 With oil a V LC1 D09 D38, DT20 DT40 LC1 D09 D38, DT20 DT40 a V LC1 D09 D38, DT20 DT40 The operating times depend on the type of ontator eletromagnet and its ontrol mode. The losing time "C" is measured from the moment the oil supply is swithed on to initial ontat of the main poles. The opening time "O" is measured from the moment the oil supply is swithed off to the moment the main poles separate. LC1 D09 D38, LC1 D40 D65 LC1 D80 and D95 DT20 DT40 With LA4 DF, LA4 DL C ms "O" ms Phillips N 2 and Ø 6 mm mm 2 Min: 1 x 1; max: 2 x 2.5 Flexible or solid able with or without able end Based on Shneider MKTED205103EN Catalogue Page 12 of 44

14 Referenes 5 For motor ontrol up to 75 kw at 400 V, in ategory AC-3 Control iruit: a.., d.. or low onsumption LC1 D09pp LC1 D25pp 3-pole ontators for onnetion by srew lamp terminals or onnetors Standard power ratings of 3-phase motors Hz in ategory AC-3 (θ y 60 C) 220 V 380 V 660 V 230 V 400 V 415 V 440 V 500 V 690 V 1000 V Rated operational urrent in AC V up to Instantaneous auxiliary ontats Basi referene, to be ompleted by adding the voltage ode (2) Fixing (1) Weight (3) kw kw kw kw kw kw A kg LC1 D09pp LC1 D12pp LC1 D18pp LC1 D25pp LC1 D32pp LC1 D38pp LC1 D40pp LC1 D50pp LC1 D65pp LC1 D80pp LC1 D95pp LC1 D115pp LC1 D150pp pole ontators for onnetion by lugs or bars In the referenes seleted above, insert a figure 6 before the voltage ode. Example: LC1 D09pp beomes LC1 D096pp Aessories Auxiliary ontat bloks and add-on modules: see pages 23 to LC1 D95pp LC1 D115pp (1) LC1 D09 to D38: lip-on mounting on 35 mm 5 rail AM1 DP or srew fixing. LC1 D40 to D95 a: lip-on mounting on 35 mm 5 rail AM1 DP or 75 mm 5 rail AM1 DL or srew fixing. LC1 D40 to D95 : lip-on mounting on 75 mm 5 rail AM1 DL or srew fixing. LC1 D115 and D150: lip-on mounting on 2 x 35 mm 5 rails AM1 DP or srew fixing. (2) Standard ontrol iruit voltages (for other voltages, please onsult your Regional Sales Offie): a.. supply Volts LC1 D09 D150 (D115 and D150 oils with integral suppression devie fitted as standard)) 50/60 Hz B7 D7 E7 F7 FE7 M7 P7 U7 Q7 V7 N7 R7 LC1 D40 D Hz B5 D5 E5 F5 FE5 M5 P5 U5 Q5 V5 N5 R5 S5 60 Hz B6 E6 F6 M6 U6 Q6 R6 d.. supply Volts LC1 D09 D38 (oils with integral suppression devie fitted as standard) U U JD BD CD ED ND SD FD GD MD UD RD LC1 D40 D95 U U JD BD CD ED ND SD FD GD MD UD RD U U JW BW CW EW SW FW MW LC1 D115 and D150 (oils with integral suppression devie fitted as standard) U U BD ED ND SD FD GD MD UD RD Low onsumption Volts LC1 D09...D38 (oils with integral suppression devie fitted as standard) U U AL JL ZL BL EL FL ML UL For other voltages between 5 and 690 V, see pages 31 to 36. (3) The weights indiated are for ontators with a.. ontrol iruit. For d.. or low onsumption ontrol iruit, add kg for ontators LC1 D09 to D38, kg for ontators LC1 D40 to D65 and 1 kg for ontators LC1 D80 and D95. Based on Shneider MKTED205103EN Catalogue Page 13 of 44

15 Referenes 5 For motor ontrol up to 15 kw at 400 V, in ategory AC-3 Control iruit: a.., d.. or low onsumption LC1 D123pp 3-pole ontators for onnetion by spring terminals Standard power ratings of 3-phase motors 50/60 Hz in ategory AC-3 (θ y 60 C) 220 V 380 V 660 V 230 V 400 V 415 V 440 V 500 V 690 V Rated operational urrent in AC V up to Instantaneous auxiliary ontats Basi referene, to be ompleted by adding the voltage ode (2) Fixing (1) Weight (3) kw kw kw kw kw kw A kg LC1 D093pp LC1 D123pp LC1 D183pp LC1 D253pp (4) 1 1 LC1 D323pp pole ontators for onnetion by Faston onnetors These ontators are fitted with Faston onnetors: 2 x 6.35 mm on the power poles and 1 x 6.35 mm on the oil and auxiliary terminals. It is possible to make 2 x 6.35 mm onnetions to the oil terminals by using a double Faston onnetor, referene: LA9 6180, to be ordered separately (sold in lots of 100). For ontators LC1 D09 and LC1 D12 only, in the referenes seleted above, replae the figure 3 before the voltage ode with a figure 9. Example: LC1 D093pp beomes LC1 D099pp. Aessories Auxiliary ontat bloks and add-on modules: see pages 23 to 30. (1) LC1 D09 to D32: lip-on mounting on 35 mm 5 rail AM1 DP or srew fixing. (2) Standard ontrol iruit voltages (for other voltages, please onsult your Regional Sales Offie): a.. supply Volts LC1 D09 D32 50/60 Hz B7 D7 E7 F7 FE7 M7 P7 U7 Q7 V7 N7 R7 d.. supply Volts LC1 D09 D32 (oils with integral suppression devie fitted as standard) U U JD BD CD ED ND SD FD GD MD UD RD Low onsumption Volts LC1 D09...D32 (oils with integral suppression devie fitted as standard) U U AL JL ZL BL EL FL ML UL For other voltages between 5 and 690 V, see pages 31 to 36. (3) The weights indiated are for ontators with a.. ontrol iruit. For d.. or low onsumption ontrol iruit, add kg for ontators LC1 D09 to D32. (4) Must be wired with 2 x 4 mm 2 ables in parallel on the upstream side. On the downstream side, outgoing terminal blok LAD 331 may be used (Quikfit tehnology). Based on Shneider MKTED205103EN Catalogue Page 14 of 44

16 Referenes 5 For ontrol in ategory AC-1, 25 to 200 A Control iruit: a.., d.. or low onsumption pole ontators for onnetion by srew lamp terminals or onnetors Non indutive loads maximum urrent (θ y 60 C) utilisation ategory AC-1 Number of poles Instantaneous auxiliary ontats Basi referene, to be ompleted by adding the voltage ode (1) Fixing (2) Weight (3) LC1 D12pp A LC1 D09pp or LC1 D12pp LC1 D18pp LC1 D25pp LC1 D32pp or LC1 D38pp LC1 D40pp LC1 D50pp or LC1 D65pp (4) LC1 D80pp or LC1 D95pp (4) LC1 D115pp or LC1 D150pp (5) pole ontators for onnetion by lugs or bars In the referenes seleted above, insert a figure 6 before the voltage ode. Example: LC1 D09pp beomes LC1 D096pp. kg pole ontators for onnetion by Faston onnetors These ontators are fitted with Faston onnetors: 2 x 6.35 mm on the power poles and 1 x 6.35 mm on the oil terminals. It is possible to make 2 x 6.35 mm onnetions to the oil terminals by using a double Faston onnetor, referene: LAD 99635, to be ordered separately (sold in lots of 100). For ontators LC1 D09 and LC1 D12 only, in the referenes seleted above, insert a figure 9 before the voltage ode. Example: LC1 D09pp beomes LC1 D099pp. LC1 D123pp 3-pole ontators for onnetion by spring terminals LC1 D093pp (6) or LC1 D123pp (6) LC1 D183pp (5) or LC1 D253pp (7) or LC1 D323pp (7) Aessories Auxiliary ontat bloks and add-on modules: see pages 23 to 30. (1) See note (1) page 16. (2) LC1 D09 to D38 and LC1 DT20 to DT40: lip-on mounting on 35 mm 5 rail AM1 DP or srew fixing. LC1 D40 to D95 a: lip-on mounting on 35 mm 5 rail AM1 DP or 75 mm 5 rail AM1 DL or srew fixing. LC1 or LP1 D40 to D95 : lip-on mounting on 75 mm 5 rail AM1 DL or srew fixing. LC1 D115 and D150: lip-on mounting on 2 x 35 mm 5 rails AM1 DP or srew fixing. (3) The weights indiated are for ontators with a.. ontrol iruit. For d.. or low onsumption ontrol iruit, add kg for ontators LC1 D09 to D38, kg for ontators LC1 D40 to D65 and 1 kg for ontators LC1 D80 and D95. (4) Seletion aording to the number of operating yles. (5) 32 A with 2 x 4 mm 2 ables onneted in parallel. (6) 20 A with 2 x 2.5 mm 2 ables onneted in parallel. (7) 40 A with 2 x 4 mm 2 ables onneted in parallel. Based on Shneider MKTED205103EN Catalogue Page 15 of 44

17 Referenes 5 For ontrol in ategory AC-1, 20 to 200 A Control iruit: a.., d.. or low onsumption pole ontators for onnetion by srew lamp terminals or onnetors Non indutive loads maximum urrent (θ y 60 C) utilisation ategory AC-1 Number of poles Instantaneous auxiliary ontats Basi referene, to be ompleted by adding the voltage ode (1) Fixing (2) Weight (3) LC1 DT20pp A LC1 DT20pp LC1 D098pp LC1 DT25pp LC1 D128pp LC1 DT32pp LC1 D188pp LC1 DT40pp LC1 D258pp LC1 D40004pp or LP1 D40004pp LC1 D40008pp or LP1 D40008pp LC1 D65004pp or LP1 D65004pp LC1 D65008pp or LP1 D65008pp LC1 D80004pp or LP1 D80004pp LC1 D80008pp or LP1 D80008pp LC1 D115004pp pole ontators for onnetion by lugs or bars In the referenes seleted above, insert a figure 6 before the voltage ode (exept LC1 D65ppp and LP1 D65ppp). Example: LC1 DT20pp beomes LC1 DT206pp. 4-pole ontators for onnetion by spring terminals LC1 DT LC1 D LC1 DT LC1 D LC1 DT LC1 D LC1 DT LC1 D Aessories Auxiliary ontat bloks and add-on modules: see pages 23 to 30. (1) Standard ontrol iruit voltages (for other voltages, please onsult your Regional Sales Offie): a.. supply Volts LC1 D09...D150 and LC1 DT20...DT40 (oils with integral suppression devie fitted as standard) 50/60 Hz B7 D7 E7 F7 FE7 M7 P7 U7 Q7 V7 N7 R7 LC1 D40...D Hz B5 D5 E5 F5 FE5 M5 P5 U5 Q5 V5 N5 R5 S5 60 Hz B6 E6 F6 M6 U6 Q6 R6 d.. supply Volts LC1 D09...D38 and LC1 DT20...DT40 (oils with integral suppression devie fitted as standard) U U JD BD CD ED ND SD FD GD MD UD RD LC1 or LP1 D40...D80 U U JD BD CD ED ND SD FD GD MD UD RD U U JW BW CW EW SW FW MW LC1 D115 (oils with integral suppression devie fitted as standard) U U BD ED ND SD FD GD MD UD RD Low onsumption Volts LC1 D09...D38 and LC1 DT20...DT40 (oils with integral suppression devie fitted as standard) U U AL JL ZL BL EL FL ML UL For other voltages between 5 and 690 V, see pages 31 to 36. (2) See note (2) page 15 (3) The weights indiated are for ontators with a.. ontrol iruit. For d.. or low onsumption ontrol iruit, add kg and for ontators LC1 D80, 1 kg. kg Based on Shneider MKTED205103EN Catalogue Page 16 of 44

18 Referenes 5 Reversing ontators for motor ontrol up to 75 kw at 400 V, in ategory AC-3 Horizontally mounted, pre-assembled Control iruit: a.., d.. or low onsumption LC2 D12pp LC2 D50pp 3-pole reversing ontators for onnetion by srew lamp terminals or onnetors Pre-wired power onnetions Standard power ratings of 3-phase motors 50/60 Hz in ategory AC-3 Operational urrent in AC V 380 V 660 V (θ y 60 C) 440 V up to 230 V 400 V 415 V 440 V 500 V 690 V 1000 V Instantaneous auxiliary ontats per ontator Contators supplied with oils Basi referene, to be ompleted by adding the voltage ode (2) Fixing (1) Weight (3) kw kw kw kw kw kw kw A kg With mehanial interlok, without eletrial interloking LC2 D09pp (4) LC2 D12pp (4) LC2 D18pp (4) LC2 D25pp (4) LC2 D32pp (4) LC2 D38pp (4) LC2 D40pp LC2 D50pp LC2 D65pp LC2 D80pp LC2 D95pp With mehanial interlok and eletrial interloking LC2 D115pp LC2 D150pp pole reversing ontators for onnetion by lugs or bars For reversing ontators LC2 D09 to LC2 D38, LC2 D115 and LC2 D150, in the referenes seleted above, insert a figure 6 before the voltage ode. Example: LC2 D09pp beomes LC2 D096pp. Aessories Auxiliary ontat bloks and add-on modules: see pages 23 to 30. (1) LC2 D09 to D38: lip-on mounting on 35 mm 5 rail AM1 DP or srew fixing. LC2 D40 to D95: lip-on mounting on 35 mm 5 rail AM1 DP or 75 mm 5 rail AM1 DL or srew fixing. LC2 D115 and D150: lip-on mounting on 2 x 35 mm 5 rails AM1 DP or srew fixing. (2) Standard ontrol iruit voltages (for other voltages, please onsult your Regional Sales Offie): a.. supply Volts LC2 D09 D150 (D115 and D150 oils with integral suppression devie fitted as standard)) 50/60 Hz B7 D7 E7 F7 FE7 M7 P7 U7 Q7 V7 N7 R7 LC2-D40 D Hz B5 D5 E5 F5 FE5 M5 P5 U5 Q5 V5 N5 R5 S5 60 Hz B6 E6 F6 M6 U6 Q6 R6 d.. supply Volts LC2 D09 D38 (oils with integral suppression devie fitted as standard) U U JD BD CD ED ND SD FD GD MD UD RD Low onsumption Volts LC2 D09...D38 (oils with integral suppression devie fitted as standard) U U AL JL ZL BL EL FL ML UL For other voltages between 5 and 690 V, see pages 31 to 36. (3) The weights indiated are for ontators with a.. ontrol iruit. For d.. or low onsumption ontrol iruit, add kg (LC2 D09 D38). (4) For reversing ontators with eletrial interloking pre-wired at the fatory, add suffix V to the referenes seleted above. Example: LC2 D09P7 beomes LC2 D09P7V. Based on Shneider MKTED205103EN Catalogue Page 17 of 44

19 Referenes 5 Reversing ontators for motor ontrol up to 15 kw at 400 V, in ategory AC-3 Horizontally mounted, pre-assembled Control iruit: a.., d.. or low onsumption pole reversing ontators for onnetion by spring terminals Pre-wired power onnetions Mehanial interlok, without eletrial interloking. LC2 D123pp Standard power ratings of 3-phase motors 50/60 Hz in ategory AC V 380 V 660 V 230 V 400 V 415 V 440 V 500 V 690 V Operational urrent in AC-3 (θ y 60 C) 440 V up to Instantaneous auxiliary ontats per ontator Contators supplied with oils Basi referene, to be ompleted by adding the voltage ode (2) Fixing (1) Weight (3) kw kw kw kw kw kw A kg LC2 D093pp LC2 D123pp LC2 D183pp LC2 D253pp LC2 D323pp pole reversing ontators for onnetion by Faston onnetors All power onnetions are to be made by the ustomer. These ontators are fitted with Faston onnetors: 2 x 6.35 mm on the power poles and 1 x 6.35 mm on the oil terminals. It is possible to make 2 x 6.35 mm onnetions to the oil terminals by using a double Faston onnetor, referene: LAD 99635, to be ordered separately (sold in lots of 100). For ontators LC2 D09 and LC2 D12 only, replae the digit 3 with a 9 in the referenes seleted above. Example: LC2 D093pp beomes LC2 D099pp. Aessories Auxiliary ontat bloks and add-on modules: see pages 23 to 30. (1) LC2 D09 to D32: lip-on mounting on 35 mm 5 rail AM1 DP or srew fixing. (2) Standard ontrol iruit voltages (for other voltages, please onsult your Regional Sales Offie). a.. supply Volts LC2 D09 D32 50/60 Hz B7 D7 E7 F7 FE7 M7 P7 U7 Q7 V7 N7 R7 d.. supply Volts LC2 D09 D32 (oils with integral suppression devie fitted as standard) U U JD BD CD ED ND SD FD GD MD UD RD Low onsumption Volts LC2 D09...D32 (oils with integral suppression devie fitted as standard) U U AL JL ZL BL EL FL ML UL For other voltages between 5 and 690 V, see pages 31 to 36. (3) The weights indiated are for reversing ontators with a.. ontrol iruit. For d.. or low onsumption ontrol iruit, add kg. Based on Shneider MKTED205103EN Catalogue Page 18 of 44

20 Referenes 5 Changeover ontator pairs for ontrol in ategory AC-1, 20 to 200 A, horizontally mounted, pre-assembled Control iruit: a.., d.. or low onsumption pole hangeover ontator pairs for onnetion by srew lamp terminals or onnetors Pre-wired power onnetions LC2 DT20 to LC2 DT40: mehanial interlok without eletrial interloking. LC2 D40 to LC2 D80: order separately 2 auxiliary ontat bloks LAD Np1 to obtain eletrial interloking between the 2 ontators (see page 24). For eletrial interloking inorporated in the mehanial interlok, please onsult your Regional Sales Offie. LC2 D115: mehanial interlok with integral, pre-wired eletrial interloking. LC2 DT20pp Utilisation ategory AC-1 Non indutive loads Maximum rated operational urrent (θ y 60 C) Instantaneous auxiliary ontats per ontator Contators supplied with oil Basi referene, to be ompleted by adding the voltage ode (1) Fixing (2) Weight A kg LC2 DT20pp LC2 DT25pp LC2 DT32pp LC2 DT40pp LC2 D40004pp LC2 D65004pp LC2 D80004pp LC2 D115004pp pole hangeover ontator pairs for onnetion by lugs or bars LC2 DT206pp LC2 DT256pp LC2 DT326pp LC2 DT406pp LC2 D LC2 D650046pp LC2 D800046pp LC2 D pp Aessories Auxiliary ontat bloks and add-on modules, see pages 23 to 30. (1) See note (1) on next page. (2) LC2 DT20 to DT40: lip-on mounting on 35 mm 5 rail AM1 DP or srew fixing. LC2 D65 and D80: lip-on mounting on 35 mm 5 rail AM1 DP or 75 mm 5 rail AM1 DL or srew fixing. LC2 D115: lip-on mounting on 2 x 35 mm 5 rails AM1 DP or srew fixing. Based on Shneider MKTED205103EN Catalogue Page 19 of 44

21 Referenes 5 Changeover ontator pairs for ontrol in ategory AC-1, 20 A, horizontally mounted, pre-assembled Control iruit: a.., d.. or low onsumption 4-pole hangeover ontator pairs for onnetion by spring terminals Pre-wired power onnetions Utilisation ategory AC-1 Non indutive loads Maximum rated operational urrent (θ y 60 C) Instantaneous auxiliary ontats per ontator Contators supplied with oil Basi referene, to be ompleted by adding the voltage ode (1) Fixing (2) Weight A kg LC2 DT203pp Aessories Auxiliary ontat bloks and add-on modules, see pages 23 to 30. (1) Standard ontrol iruit voltages (for other voltages, please onsult your Regional Sales Offie). a.. supply Volts LC2 DT20 DT40 50/60 Hz B7 D7 E7 F7 FE7 M7 P7 U7 Q7 V7 N7 R7 LC2 D65 D Hz B5 D5 E5 F5 FE5 M5 P5 U5 Q5 V5 N5 R5 S5 60 Hz B6 E6 F6 M6 U6 Q6 R6 d.. supply Volts LC2 DT20 DT40 (oils with integral suppression devie fitted as standard) U U JD BD CD ED ND SD FD GD MD UD RD Low onsumption Volts LC2 DT20...DT40 (oils with integral suppression devie fitted as standard) U U AL JL ZL BL EL FL ML UL For other voltages between 5 and 690 V, see pages 31 to 36. (2) Clip-on mounting on 35 mm 5 rail AM1 DP or srew fixing. Based on Shneider MKTED205103EN Catalogue Page 20 of 44

22 Referenes 5 Component parts for assembling reversing ontators for motor ontrol or low speed - high speed starters For 3-pole reversing ontators for motor ontrol Contators with srew lamp terminals or onnetors Horizontally mounted, assembled by ustomer Using 2 idential Set of power onnetions Mehanial interlok ontators (1) Referene Weight Kit referene Weight kg kg Inluding mehanial interlok and an eletrial interloking kit for the ontators LC1 D09 D38 LAD 9R1V (2) LA9 D4002 Inluding mehanial interlok with integral eletrial interloking LC1 D40 D65 LA9 D LA9 D LC1 D80 and D95 (a) LA9 D LA9 D LC1 D80 and D95 () LA9 D LA9 D LC1 D115 and D150 LA9 D LA9 D LA9 D6569 Inluding mehanial interlok without eletrial interloking LC1 D09 D38 LAD 9R1 (2) with srew lamp terminals or onnetors LC1 D09 D32 (3) with spring terminal onnetions LC1 D40 D65 LA9 D LA9 D LC1 D80 and D95 (a) LA9 D LA9 D LC1 D80 and D95 () LA9 D LA9 D LA9 D8069 For low speed - high speed starter Desription For ontators with onnetions Referene Weight kg Connetion kit enabling reversing of low and high speed diretions, using a reversing ontator and a 2N/O + 2N/C main pole ontator Srew lamps or onnetors LAD 9PVGV Power onnetion module with spring terminal onnetions Outgoing terminal blok with spring terminal onnetions LAD 3PVGV LAD 3PVGV LAD 9R1 (1) To order the 2 ontators: see pages 13 and 14. (2) Inluding mehanial interlok. (3) To build a reversing ontator with spring terminal onnetions, the following omponents must be ordered: - 1 mehanial interlok LAD 9V2, - 1 upstream power onnetion kit and 1 downstream power onnetion kit. Upstream power onnetion kit LAD 9V10: installed in the Quikfit system with power onnetion module LAD 34. (If module LAD 34 is not used, replae LAD 9V10 with LAD 9V12). Downstream power onnetion kit LAD 9V11: installed in the Quikfit system with outgoing terminal blok LAD 331. (If module LAD 331 is not used, replae LAD 9V11 with LAD 9V13). Based on Shneider MKTED205103EN Catalogue Page 21 of 44

23 Referenes 5 Component parts for assembling hangeover ontator pairs for distribution For 4-pole hangeover ontator pairs (3-phase distribution + neutral) Contators with srew lamp terminals or onnetors Horizontally mounted, assembled by ustomer Using 2 idential Set of power onnetions Mehanial interlok ontators (1) Referene Weight Kit referene Weight kg kg Inluding mehanial interlok and an eletrial interloking kit for the ontators LC1 DT20 DT40 LAD T9R1V (2) LA9 D4002 Inluding mehanial interlok with integral eletrial interloking LC1 D65004 LA9 D LA9 D LC1 D80004 LA9 D LA9 D LP1 D80004 LA9 D LA9 D LC1 D LA9 D LA9 D LA9 D50978 Inluding mehanial interlok without eletrial interloking LC1 DT20 DT40 LAD-T9R1 (2) with srew lamp terminals or onnetors LC1 DT203 DT403 (3) with spring terminal onnetions LC1 or LP1 D65004 LA9 D6570 (4) LA9 D LC1 D80004 LA9 D8070 (4) LA9 D LP1 D80004 LA9 D8070 (4) LA9 D LA9 D6570 For 3-pole hangeover ontator pairs Inluding mehanial interlok with integral eletrial interloking LC1 D115 and D150 LA9 D LA9 D LA9 D8070 (1) To order the 2 ontators: see pages 16 and 17. (2) Inluding mehanial interlok. (3) To build a hangeover ontator pair with spring terminal onnetions, the following omponents must be ordered in addition to the 2 ontators: - 1 mehanial interlok LAD 9V2, - 1 downstream power onnetion kit LAD 9V9. (4) Order 2 ontat bloks LAD Np1 to build the eletrial interlok, see page 24. Based on Shneider MKTED205103EN Catalogue Page 22 of 44

24 Presentation 5 d ontators and reversing ontators Instantaneous auxiliary ontat bloks See page opposite for mounting possibilities aording to the ontator type and rating. Based on Shneider MKTED205103EN Catalogue Page 23 of 44

25 Referenes 5 d ontators and reversing ontators Instantaneous auxiliary ontat bloks Instantaneous auxiliary ontat bloks for onnetion by srew lamp terminals For use in normal operating environments In order to mount an LAD 8N on an LC1 D40 to D95, a set of shims must be ordered separately, see page 30 Clip-on mounting (1) Number of ontats per blok Composition Referene Weight kg Front 1 1 LAD N LAD N LAD N LAD N LAD N LAD N LAD N LAD N LAD N LAD N inl. 1 N/O & 1 N/C 2 2 LAD C make before break Side LAD 8N LAD 8N LAD 8N For terminal referening onforming to EN Front, on 3P ontators and 4P ontators 20 to 60A LAD N11G LAD N22G Front, on 4P ontators LAD N11P to 200A LAD N22P With dust and damp proteted ontats, for use in partiularly harsh industrial environments Front 2 2 L DX L DX L DX L DY20 (2) L DZ L DZ Instantaneous auxiliary ontat bloks for onnetion by lugs This type of onnetion is not possible for bloks with 1 ontat or bloks with dust and damp proteted ontats. For all other instantaneous auxiliary ontat bloks, add the figure 6 to the end of the referenes seleted above. Example: LAD N11 beomes LAD N116. Instantaneous auxiliary ontat bloks for onnetion by spring terminals This type of onnetion is not possible for LAD 8, LAD N with 1 ontat or bloks with dust and damp proteted ontats. For all other ontat bloks, add the figure 3 to the end of the referenes seleted above. Example: LAD N11 beomes LAD N113. Instantaneous auxiliary ontat bloks for onnetion by Faston onnetors This type of onnetion is not possible for LAD 8, LAD N with 1 ontat or bloks with dust and damp proteted ontats. For all other ontat bloks, add the figure 9 to the end of the referenes seleted above. Example: LAD N11 beomes LAD N119. (1) Maximum number of auxiliary ontats that an be fitted Contators Instantaneous auxiliary ontats Time delay Type Number of poles and size Side mounted Front mounted 1 ontat 2 ontats 4 ontats a 3P LC1 D09 D38 1 on LH side and 1 or 1 or 1 LC1 D40 D95 (50/60 Hz) 1 on eah side or 2 and 1 or 1 or 1 LC1 D40 D95 (50 or 60 Hz) 1 on eah side and 2 and 1 or 1 or 1 LC1 D115 and D150 1 on LH side and 1 or 1 or 1 4P LC1 DT20 DT40 1 on LH side and 1 or 1 or 1 LC1 D40 D80 1 on eah side or 1 or 1 or 1 or 1 LC1 D115 1 on eah side and 1 or 1 or 1 or 1 3P LC1 D09 D38 1 or 1 or 1 LC1 D40 D95 2 and 1 or 1 or 1 LC1 D115 and D150 1 on LH side and 1 or 1 or 1 4P LC1 DT20 DT40 1 or 1 or 1 LC1 D40 D80 2 and 1 or 1 or 1 LC1 D115 1 on eah side and 1 or 1 or 1 LC (3) 3P LC1 D09 D38 1 4P LC1 DT20 DT40 1 (2) Devie fitted with 4 earth sreen ontinuity terminals. (3) LC: low onsumption. Front mounted Based on Shneider MKTED205103EN Catalogue Page 24 of 44

26 Referenes 5 d ontators and reversing ontators Time delay auxiliary ontat bloks Mehanial lath bloks Time delay auxiliary ontat bloks for onnetion by srew lamp terminals Maximum number of auxiliary ontat bloks that an be fitted per ontator, see page 24. Sealing over to be ordered separately, see page 30. LAD T0 and LAD R0: with extended sale from 0.1 to 0.6 s. LAD S2: with swithing time of 40 ms ± 15 ms between opening of the N/C ontat and losing of the N/O ontat. Clip-on mounting Number of Time delay Referene Weight ontats Type Setting range per blok kg Front 1 N/O + 1 N/C On-delay s LAD T s LAD T s LAD T s LAD S LAD T Off-delay s LAD R s LAD R s LAD R Time delay auxiliary ontat bloks for onnetion by lugs Add the figure 6 to the end of the referenes seleted above. Example: LAD T0 beomes LAD T06. Time delay auxiliary ontat bloks for onnetion by spring terminals Add the figure 3 to the end of the referenes seleted above. Example: LAD T0 beomes LAD T03. LA6 DK Time delay auxiliary ontat bloks for onnetion by Faston onnetors Add the figure 9 to the end of the referenes seleted above. Example: LAD T0 beomes LAD T LAD Tp3 LA6 DK Mehanial lath bloks (1) Clip-on mounting Unlathing ontrol For use on ontator Front Manual or eletri LC1 D40 D65 (3 P a or ) LC1 D40 and D65 (4 P a) LP1 D40 and D65 (4 P ) Basi referene, Weight to be ompleted by adding the voltage ode (2) kg LA6 DK10p LC1 D80 D150 (3 P a) LA6 DK20p LC1 D80 and D115 (3 P ) LC1 D80 (4 P a) LC1 D80 & D115 (4 P a) LP1 D80 & LC1 D115 (4 P ) LC1 D09 D38 (a or ) LC1 DT20 DT40 (a or ) LAD 6K10p (1) The mehanial lath blok must not be powered up at the same time as the ontator. The duration of the ontrol signal for the mehanial lath blok and the ontator should be: u 100 ms for a ontator operating on an a.. supply u 250 ms for a ontator operating on a d.. supply (2) Standard ontrol iruit voltages (for other voltages, please onsult your Regional Sales Offie): Volts 50/60 Hz, 24 32/36 42/48 60/ / / / /415 Code B C E EN K F M U Q Based on Shneider MKTED205103EN Catalogue Page 25 of 44