Contactors. Motor Starters and Protectors. Overload Relays. Soft Start Module ATS Replacement Parts. Wiring Systems.

Transcription

1 Table of Contents Setion 18 TeSys IEC Contators and Starters Contators TeSys D Contators (p. 18-4) TeSys D 18-4 TeSys D Reversing 18-6 TeSys F 18-5 TeSys D and F Aessories 18-8 TeSys K TeSys K Aessories Motor Starters and Protetors TeSys F Contators (p. 18-5) GV7 Manual Motor Starters and Protetors (p ) TeSys F1700, F2100 TeSys U GV2, GV3, GV7 Manual Motor Protetors Enlosed D-Line GV Aessories LS1D Fuse Blok Overload Relays TeSys D 18-4 TeSys F 18-5 TeSys D and F Aessories TeSys K TeSys K Aessories TeSys T Motor Management System Setion 16 Soft Start Module ATS Replaement Parts TeSys D Coils TeSys F Coils TeSys F Contat Tips, et GV3P (p.18-33) LUB 2 (p ) GV2P21 (p.18-33) Wiring Systems GV-Line Bus Bars TeSys D Quikfit AK Dimensions Dimensions For more information on lighting, definite purpose (DP), and elevator ratings for TeSys D and TeSys F ontators, refer to atalog 8502CT9901. For more information on mahine safety appliations using TeSys D and TeSys F ontators, refer to atalog MKTED208051EN-US. See our website, for UL 508A short iruit ratings (SCCR) Shneider Eletri 18-1 This doument provided by Barr-Thorp Eletri Co., In

2 3-Pole Contators TeSys D AC and DC Contators Refer to 8502CT Table 18.1: TeSys D Contators Interpretation of the LC D Full Voltage, Non-Reversing 1 Full Voltage, Reversing 2 TeSys D 3 Pole Contators, A Contator AC-3 Full Load Amperes (FLA) 9 A FLA A FLA A FLA A FLA A FLA A FLA A FLA A FLA A FLA A FLA A FLA 150 Everlink Power Connetion (40 65 A only) A No Everlink Power Connetion (9 32 A, A) Blank Termination Options (hoose one) Srew Termination Blank Spring Terminations s 3 Ring Tongue Terminations t 6 Slip-on Terminations (9 12 A only) 9 Coil Voltage (hoose one) AC Coils (50/60 Hz) DC Coils (standard) DC Coils low onsumption available for 9 38 A only 12 V J7 12 V JD 5 V AL 21 V Z7 21 V ZD 12 V JL 24 V B7 24 V BD 21 V ZL 36 V C7 36 V CD 24 V BL 42 V D7 48 V ED 48 V EL V E7 ND 72 V SL s t Note: For spring terminal versions of LC1D09 LC1D65A, add 3 to the atalog number prior to adding the voltage ode (for example, LC1D12G7 beomes LC1D123G7, and LC1D40AG7 beomes LC1D40A3G7. Note that A spring terminals are only on the ontrol terminations and not on power terminations). There is no harge for this modifiation. For ring tongue versions of LC1D09 LC1D65A and LC1DT20 LC1DT80A, add 6 to the atalog number prior to adding the voltage ode (for example, LC1D09G7 beomes LC1D096G7, and LC1D50AG7 beomes LC1D50A6G7). There is no harge for this modifiation. Use this table only to interpret urrent atalog numbers. Some ombinations are not available. 60 V EE7 72 V SD 96 V DL 100 V K7 110 V FD 110 V FL 110 V F7 125 V GD 220 V ML 115 V FE7 220 V MD 250 V UL 120 V G7 250 V UD 127 V FC7 440 V RD 200 V L7 208 V LE7 220 V M7 230 V P7 240 V U7 277 V W7 380 V Q7 400 V V7 415 V N7 440 V R7 480 V T7 500 V S7 575 V SC7 600 V X7 660 V Y5 (50 Hz only) Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

3 2, 3, and 4 Pole Contators TeSys F AC and DC Contators Refer to 8502CT9901 Table 18.2: TeSys F Contators Interpretation of the LC F Full Voltage, Non-Reversing 1 Full Voltage, Reversing 2 TeSys F 2, 3, and 4 Pole Contators A Contator AC-3 Full Load Amperes (FLA) 115 A FLA A FLA A FLA A FLA A FLA A FLA A FLA A FLA A FLA A FLA A FLA 800 of Poles 2 Poles (400 A, 500 A, and 630 A only) 2 3 Poles (all sizes) Blank 4 Poles (all sizes exept 800 A) 4 Termination Options Purhase Lugs Separately Coil Voltage (hoose one, noting the ontator size it an be used on) Blank AC Coils For use on: AC Coils For use on: 24 V (50 Hz) B5 LC1F115 F V P7 LC1F1700, F V (60 Hz) B6 LC1F115 F V (50 Hz) U5 LC1F115 F V ( Hz) B7 LC1F225 F V (60 Hz) U6 LC1F115 F V (50 Hz) D5 LC1F115 F V ( Hz) U7 LC1F115 F V (50 Hz) E5 LC1F115 F V U7 LC1F1700, F V (60 Hz) E6 LC1F115 F V (50 Hz) W5 LC1F115 F V ( Hz) E7 LC1F115 F V ( Hz) W7 LC1F115 F V (50 Hz) F5 LC1F115 F V W7 LC1F1700, F V (60 Hz) F6 LC1F115 F V (50 Hz) Q5 LC1F115 F V F7 LC1F1700, F V (60 Hz) Q6 LC1F115 F V ( Hz) F7 LC1F115 F V ( Hz) Q7 LC1F115 F V (50 Hz) FE5 LC1F115 F V Q7 LC1F1700, F V ( Hz) FE7 LC1F115 F V (50 Hz) V5 LC1F115 F V (60 Hz) G6 LC1F115 F V ( Hz) V7 LC1F115 F V G7 LC1F1700, F V V7 LC1F1700, F V ( Hz) G7 LC1F115 F V (50 Hz) N5 LC1F115 F V ( Hz) F7 LC1F500 F V ( Hz) N7 LC1F115 F V (60 Hz) G6 LC1F115 F V N7 LC1F1700, F V ( Hz) G7 LC1F115 F V (50 Hz) R5 LC1F115 F /208 V (60 Hz) L6 LC1F115 F V ( Hz) R7 LC1F115 F /208 V ( Hz) L7 LC1F265 F V R7 LC1F1700, F V ( Hz) L7 LC1F115 F /480 V (60 Hz) Q6 LC1F115 F V (50 Hz) M5 LC1F115 F V ( Hz) N7 LC1F V (60 Hz) M6 LC1F115 F V (50 Hz) S5 LC1F115 F V ( Hz) M7 LC1F115 F V ( Hz) S7 LC1F115 F V M7 LC1F1700, F V S7 LC1F1700, F V (50 Hz) P5 LC1F115 F V ( Hz) X7 LC1F500 F V ( Hz) P7 LC1F115 F V (60 Hz) Y6 LC1F115 F225 DC Coils For use on: 24 V BD LC1F115 F V ED LC1F115 F V FD LC1F115 F V FD LC1F1700, F V FW LC1F V GD LC1F115 F V GD LC1F1700, F V MD LC1F265 F V UD LC1F1700, F /240 V MW LC1F V UD LC1F115 F /400 V QW LC1F V RD LC1F1700, F V RD LC1F115 F Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

4 Contators & Overload Relays LC1D09 LC1D093 LC1D40A LC1D115 LRD22 LRD3 E CCN NLDX LR43364 Class Table 18.3: TeSys D Non-reversing Refer to 8502CT9901 TeSys D Contators 3 or 4 Pole, Srew Terminal Connetions Maximum Current Maximum Horsepower Ratings Utilization Categories Single-Phase Three-Phase Indutive Resistive AC3 AC1 (A) (A) No. of Poles Instantaneous Auxiliary Contats a LRD01 LR3D LRD02 LR3D LRD03 LR3D LRD04 LR3D D09 D32 LRD05 LR3D LRD06 LR3D LRD07 LR3D LRD08 LR3D08 LRD1508 LR3D1508A1 4 6 LRD10 LR3D10 LRD1510 LR3D1510A D09 D32 LRD12 LR3D12 LRD1512 LR3D1512A D09 D32 LRD14 LR3D14 LRD1514 LR3D1514A D12 D32 LRD16 LR3D16 LRD1516 LR3D1516A D18 D32 LRD21 LR3D21 LRD1521 LR3D1521A D25 D32 LRD22 LR3D D25 D32 LRD1522 LR3D1522A D25 D32 LRD32 LR3D D25 D32 LRD1530 LR3D1530A D25 D32 LRD1532 LR3D1532A D32 LRD35 LR3D D40A-D65A f LRD313 LR3D313 LRD313L D40A-D65A f LRD318 LR3D318 LRD318L D40A-D65A f LRD325 LR3D325 LRD325L D40A-D65A f LRD332 LR3D332 LRD332L D40A-D65A f LRD340 LR3D340 LRD340L D40A-D65A f LRD350 LR3D350 LRD350L D40A-D65A f LRD365 LR3D365 LRD365L D40-D80 g LRD3322 LR3D3322 LR2D3522 LR3D D40-D80 g LRD3353 LR3D3353 LR2D3553 LR3D D40-D80 g LRD3355 LR3D3355 LR2D3555 LR3D D50-D80 g LRD3357 LR3D3357 LR2D3557 LR3D D50-D80 g LRD3359 LR3D3359 LR2D3559 LR3D D65 D80 LRD3361 LR3D3361 LR2D3561 LR3D D65 D80 LRD3363 LR3D3363 LR2D3563 LR3D D80 LRD D115 D150 LRD D115 D150 LRD D150 LRD4369 f Overload relays with Everlink termination diret mount to D40A to D65A only. g Diret mount to old D2 style D40 to D65 (no Everlink terminations) and to D80 only. TeSys D ontator aessories pages 18-8 to TeSys D overload relay aessories page TeSys D replaement oils page Dimensions pages to TeSys T pages N.O. N.C. N.O. N.C. 115 V hp 230 V hp 200 V hp 230 V hp 460 V hp 575 V hp AC Coils DC Coils 3 LC1D09 de LC1DT LC1D LC1D12 de LC1DT LC1D LC1D18 d LC1DT LC1D LC1D25 d LC1DT LC1D LC1D32 d LC1D40A LC1DT60A LC1D50A LC1D65A LC1DT80A LC1D LC1D80004 b LC1D80008 b LC1D LC1D LC1D a Complete the atalog number by adding the oil voltage ode from Table on page 18-6 (for example, LC1D09G7). b For DC version of these devies, replae the C with a P (for example, LC1D80004 beomes LP1D80004 ). This applies only to 80 A, 4-pole devies. For ring tongue versions of LC1D09 LC1D65A and LC1DT20 LC1DT80A, add 6 to the atalog number prior to adding the voltage ode (for example, LC1D09G7 beomes LC1D096G7 and LC1D50AG7 beomes LC1D50A6G7). There is no harge for this modifiation. d For spring terminals versions of LC1D09 LC1D65A, add 3 to the atalog number prior to adding the voltage ode (for example, LC1D12G7 beomes LC1D123G7 and LC1D40AG7 beomes LC1D40A3G7. Note that A spring terminals are only on the ontrol terminations and not on power terminations). Ring tongue terminations have a 10% adder to list prie. e For slip-on onnetor versions of LC1D09 and LC1D12 only, add 9 to the atalog number prior to adding the voltage ode (for example, LC1D09G7 beomes LC1D099G7). There is no harge for this modifiation. Table 18.4: Current Setting Range (A) TeSys D Overload Relays Ambient Compensated, Bimetalli, Diret Mounting For Diret Mounting to LC1... Class 10 with Single-Phase Sensitivity Class 10 without Single-Phase Sensitivity Class 20 with Single-Phase Sensitivity Class 20 without Single-Phase Sensitivity Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

5 Contators & Overload Relays TeSys F Non-reversing Refer to 8502CT9901 LC1F115 LC1F1700, F2100 E CCN NLDX LR43364 Class Table 18.5: TeSys D Overload Relays Solid State Current Setting Range (A) For Diret Mounting Beneath Contator LC1 Class 10 Class D115 D150 LR9D5367 LR9D D115 D150 LR9D5369 LR9D Table 18.6: TeSys F Contators 2, 3, and 4 Pole Standard power ratings of 3-phase motors 50/60 Hz in ategory AC-3 Maximum Current a 200 V / 208 V 220 V / 240 V 460 V / 480 V 575 V / 600 V AC-3 AC-1 of Poles Panel Mounting HP HP HP HP A A with Srews LC1F LC1F LC1F LC1F LC1F LC1F Current Rated LC1F LC1F LC1F LC1F LC1F LC1F LC1F LC1F LC1F LC1F LC1F LC1F LC1F LC1F LC1F Current Rated LC1F LC1F LC1F Current Rated LC1F , LC1F , a Complete the part number by adding the oil voltage ode from Table 18.8 (for example, LC1F115G7). All ontators exept F780 inlude 1 N.O. oil interlok ontat. Table 18.7: b d Current Setting Range A TeSys F 3-Phase Overload Relays Solid State, Separate Mounting b For Diret Mounting to Contator LC1 TeSys F ontator aessories page TeSys F overload relay aessories page TeSys F replaement oils and parts pages 18-13, 18-18, Dimensions pages to Class 10 Trip Class F115 F185 LR9F5357 LR9F F115 F185 LR9F5363 LR9F F115 F185 LR9F5367 LR9F F115 F185 LR9F5369 LR9F F185 d F265 LR9F5371 LR9F F265 F500 LR9F7375b LR9F7575b F265 F500 LR9F7379b LR9F7579b F400 F630 LR9F7381b LR9F7581b When mounting overload relays LR9F5 57 LR9F5 71 diretly beneath the ontator, supporting the relays with a mounting plate is reommended. With overload relays LR9F7 75 LR9F7 81, use of a support mounting plate is mandatory. IEC standard speifies the following trip times when the overload relay senses 7.2 times the setting urrent: Class 10 between 4 and 10 seonds; Class 20 between 6 and 20 seonds. Interonnetion kit LA7F407 is required to mount an LR9F 71 to an LC1F185. Table 18.8: e f g h i j Coil Voltage Codes h Contator Hz 24 V 48 V 110 V 120 V 208 V 220 V 240 V 440 V 480 V 500 V 600 V AC D09 D150 50/60 B7 E7 F7 G7 LE7 M7 U7 T7 e X7 ef LC1D80 LC1D150 only 60 B6 E6 F6 G6 L6 M6 U6 T6 X6 f 50 B5 E5 F5 M5 e U5 F115, F150, and F B5 E5 F5 M5 U5 60 B6 E6 F6 G6 L6 M6 U6 Q5 S7 F265, and F B7 E7 F7 G7 L7 M7 U7 S7i X7 F400 F E7 F7 G7 L7 M7 U7 N7 X7 g F1700 F F7 G7 M7 U7 R7 S7 Contator Hz 24 V 48 V 110 V 125 V 220 V 250 V 440 V DC j D09-D32, DT20-D258 Low Consumption BL EL FL ML UL D09 D150 BD ED FD GD MD UD RD F115-F330 BD ED FD GD MD UD RD F400 F780 ED FD GD MD UD RD F1700 F2100 FD GD MD UD RD Not available for LC1D80. Not available for LC1D115 or LC1D150. Not available for LC1F780. The 600 V oils for LC1F400 LC1F630 do not inlude an auxiliary ontat for holding iruits. For additional voltage odes refer to the IEC Contator and Starter 8502CT9901. For use with F265 F330 only. DC oils 3-pole ontators are fitted with built-in surge suppression as standard. Table 18.9: Coil Voltage Codes for AC and DC Voltages for F800 (inludes built-in surge suppressor) Va/Vd /60 HZ FW FW FW MW MW QW QW QW 2012 Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

6 Contators LC2D09 TeSys D 3- and 4-Pole Reversing, AC or DC Operating Coil Refer to 8502CT9901 Eah 3-pole devie is prewired with line and load side power wiring for reversing appliations. Eah 4-pole devie is prewired with load side power wiring. Table 18.10: 3-Pole and 4-Pole Mehanially Interloked Contators Maximum Horsepower Ratings Maximum Current Built In Auxiliary No. of N.O. Contats Single Phase Three Phase Indutive Resistive Power (per ontator) AC DC AC3 (A) AC1 (A) Poles ab 115 V hp 230 V hp 200 V hp 230 V hp 460 V hp 575 V hp N.O. N.C. Control Control LC2D LC2DT LC2D LC2DT LC2D LC2DT LC2D LC2DT LC2D LC2D40A LC2D50A LC2D65A d d LC2D115 e LC2D e LC2D150e a Use voltage odes from Table to omplete the atalog number (for example, LC2D09G7). b Inludes mehanial interlok without eletrial ontats. Installer to omplete wiring for eletronially interloking ontator operating oils by using a N.C. auxiliary ontat integrated in the ontator or optional LADN or LAD8N auxiliary ontat blok. For LC2D09 LC2D32, eletrial interlok an be inluded by adding a V to the end of the atalog number (for example LC2DO9B7V). List prie adder: $5.00. d For these items, order two non-reversing ontators and one mehanial interlok separately. See page 18-4 and for seletion. e Inludes mehanial interlok (LA9D11502) with prewired eletrial ontats for interloking ontator operating oils. Table 18.11: Coil Voltage Codes i Contator Hz 24 V 48 V 110 V 120 V 125 V 208 V 220 V 240 V 250 V 440 V 480 V 600 V AC D09 D150 50/60 B7 E7 F7 G7 LE7 M7 U7 T7 f X7 f LC1D80 LC1D B5 E5 F5 M5 f U5 60 B6 E6 F6 G6 L6 M6 U6 T6 X6 gf F115, F150, F Hz B5 E5 F5 M5 U5 60 Hz B6 E6 F6 G6 L6 M6 U6 Q5 SC F265, F Hz B7 E7 F7 G7 L7 M7 U7 S7 j X7 F400 F Hz E7 F7 F7 L7 M7 U7 N7 X7 h DC D09-D32, DT20-D258 BL EL FL ML UL Low Consumption D09 D150 BD ED FD GD MD UD RD F115 F330 BD ED FD GD MD UD RD F400 F780 ED FD GD MD UD RD f Not available for LC1D80 LC1D150. g Not available for LC1D115 or LC1D150. h Not available for LC1F780. The 600 V oils for LC1F400 LC1F630 do not inlude an auxiliary ontat for holding iruits. i For additional voltage odes refer to the IEC Contator and Starter atalog, 8502CT9901. j For use with F265 F330 only. Table 18.12: Coil Voltage Codes for AC and DC Coil Voltages for F800 (inludes built-in surge suppressor) Va/Vd /60 Hz FW FW FW MW MW QW QW QW TeSys D ontator aessories pages 18-8 to TeSys D overload relay aessories page TeSys D replaement oils pages to Dimensions pages to E CCN NLDX LR43364 Class Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

7 LC1F265 Contators TeSys F 3-Pole Reversing, AC or DC Operating Coil Refer to 8502CT9901 How to Order: Components are available for ustomer assembly of TeSys F reversing ontators. For example, the following omponents must be ordered to build a reversing ontator, V, with a 120 V / 60 Hz oil: Table 18.13: Example of Components Desription Quantity Contators 2 LC1F115G6 Lugs (page 18-12) 6 DZ2FF1 Auxiliary ontats 2 LADN11 Power onnetions 1 LA9FF976 Mehanial interlok 1 LA9FF970 Table 18.14: 3-Pole Contators Maximum Horsepower Ratings Maximum Current Holding Ciruit Contat Built Three Phase Into Coil 200 V hp 230 V hp 460 V hp 575 V hp Indutive AC3 (A) Resistive AC1 (A) N.O. N.C. a LC1F LC1F LC1F LC1F LC1F LC1F LC1F LC1F Current rated LC1F LC1F a Use oil voltage odes from the Voltage Codes table on page 18-6 to omplete the ontator atalog number. Table 18.15: Auxiliary Contat (Eletrial Interloking) 2 must be purhased b For use with LC1F to be ordered separately of Contats Maximum of Bloks Per Contator inluding 1 N.O. + 1 N.C. make-before-break Contat Arrangement 1 LADN LADN LADN LADN LADN LADN LADN LADN LADN b LADC Table 18.16: Aessories For the Assembly of 3-Pole Reversing Contators (Horizontal Mounting) With 2 Idential Contators Set of Power Connetions Horizontal Mounting Mehanial Interlok Kit LC1F115 LA9FF LA9FF LC1F150 LA9F LA9FF LC1F185 LA9FG LA9FG LC1F265 LA9FH LA9FJ LC1F330 LA9FJ LA9FJ LC1F400 LA9FJ LA9FJ LC1F500 LA9FK LA9FJ LC1F630, F800 LA9FL LA9FL For two ontators of different size, refer to pages TeSys F ontator aessories page TeSys F overload relay aessories page TeSys F replaement oils and parts pages 18-13, 18-18, Dimensions page E CCN NLDX LR43364 Class Table 18.17: Definite Purpose Ratings, 3-Phase, Breaking All Lines (Hermeti Refrigeration Compressor) LRA Devie FLA 240V 480V 600V LC1D09 (AC oil only) LC1D12 (AC oil only) LC1D18 (AC oil only) LC1D25 (AC oil only) LC1D32 (AC oil only) LC1D40A LC1D50A LC1D65A LC1D LC1D95 LC1D LC1D Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

8 Contator Aessories TeSys D & F Auxiliary Contats, Time Delay, Mehanial Lath Refer to 8502CT Front Mounted Auxiliary Bloks Table 18.18: Standard, Instantaneous Auxiliary Contat Bloks a b d e Snap-On Mounting To front of LC DT20 D258 (4P), LC D09 D150a or To right side of LC F To front of LC D80 and D115 or To left side of LC F of Contats 4 a 2 1 Composition N.O. N.C. a 2 2 LADN22 b LADN13 b LADN40 b LADN04 b LADN31 b LADC22 b LADN11 b LADN20 b LADN02b LADN10 d LADN01 d To side of LC D09 to D150 only LAD8N11 e (not for use on TeSys F) 2 0 LAD8N20 e For low onsumption oils (LC1D09 D32 only), only one front-mounted two-ontat blok allowed. No sidemounted ontat bloks allowed. For spring terminal versions of these bloks, add a 3 to the end of the atalog number (for example, LADN223). There is no harge for this modifiation. For slip-on versions, add 9 to the end of the atalog number (for example, LADN229). Inluding 1 N.O. + 1 N.C. make-before-break overlapping ontats. This blok annot be added to the LC1D 09 D32 ontators; a maximum of 2 bloks an be mounted on the LC1D40A LC1/LP1D80 ontators only. 1 blok may be added to the left side of LC1D09 D32, AC oils only; only 1 blok may be added to either side of the LC1D40A D80 ontators, AC oils only. Cannot be installed on TeSys D ontators with DC oils. Table 18.19: Instantaneous Bloks with Dust-Tight Auxiliary Contats (IP54) NEMA 12 Snap-On Mounting To front of LP D40 D80, LC DT20 D258 (4P), LC D09 to D80 or To right side of LC F f Standard Contats Devie supplied with 4 ground terminal points. Dust-Tight Contats N.O. N.C. N.O. N.C. Table 18.20: Pneumati Time Delay Contat Bloks Snap-On Mounting To front of LP D40 D80, LC DT20 D258 (4P), LC D09 to D150 or To right side of LC F Time Delay Contats N.O. N.C LA1DX LA1DZ LA1DZ LA1DY20f Type On energization (on delay) On de-energization (off-delay) Range of Time Delay h 0.1 to 3 sg LADT to 30 s LADT to 180 s LADT to 30 si LADS to 3 sg LADR to 30 s LADR to 180 s LADR g Sale range is expanded between 0.1 and 0.6 seonds on the dial for more aurate settings at the lower end of the range. h For spring terminal versions of these bloks, add a 3 to the end of the atalog number (for example, LADT23). There is no harge for this modifiation. i Swithing time between the opening of the N.C. ontat and the losing of the N.O. ontat: 40 ms ± 15 ms. Table 18.21: Mehanial Lath Bloks with Manual or Eletrial Unlath (TeSys D only) Front snap-on mounting onto Appliation k LC D09 to D65A For silent operation and energy onservation LAD6K10jkl LC1 D80 to D150 LP1 D80 For silent operation and energy onservation LA6DK20jk j Does not inlude internal oil learing ontat. k Complete the atalog number by adding the oil voltage ode (for example, LAD6K10F). l Low onsumption DC ontators (and relays) (ode oil xl) are not ompatible with the LAD6K10x mehanial lathing bloks. Table 18.22: Coil Voltage Codes for LA6DK Mehanial Lath Bloks Volts /36 42/48 60/ AC or DC J B C E EN K F L M Q R S 110/ / / / / / 600 E CCN NLDX LR43364 Class TeSys D ontators pages 18-4, 18-6 TeSys D overload relay aessories page TeSys D replaement oils pages to Dimensions pages to Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

9 LA4DA1U LA4DC3U LAD4T3B LAD4BB Contator Aessories TeSys D Coil Suppressors, Cabling Aessories RC Coil Suppressor Limitation of transient voltage to 300% of nominal voltage maximum. Osillating frequeny limited to 400 Hz maximum. Slight inrease in drop-out time (1.2 to 2 times normal). Varistor Coil Suppressor Limitation of transient voltage value to 200% of nominal voltage maximum. Maximum redution of transient voltage peaks. Slight inrease in drop-out time (1.1 to 1.5 times normal). Diode Coil Suppressor No overvoltage or osillating frequeny. Polarized omponent. Inreased drop-out time (6 10 times normal). Bidiretional Diode Coil Suppressor Protetion provided by limiting the transient voltage to 2 U max. Maximum redution of transient voltage peaks TeSys D ontators pages 18-4, 18-6 TeSys D overload relay aessories page TeSys D replaement oils pages to Dimensions pages to Refer to 8502CT9901 Table 18.23: Resistor/Capaitor Ciruit (RC) for Redution of Eletrial Noise in AC Contator Coils Installed by Mounting on Operating Voltage 50/60 Hz Snapping into the avity on the right side without toolsm Snap-on mounting, and onnetion without tools to the ontator oil terminals Srew onnetion to the ontator oil terminals LC1D09 to LC1D32 (3P) LC DT20 to DT40 (4P), LC1D40A to LC1D65A (3P), LC1DT60A to LC1DT80A (4P) LC D80 to D150 (3P or 4P) LC D80 to D115 (4P) V LAD4RCE V LAD4RCG V LAD4RCU V LAD4RC3E V LAD4RC3G V LAD4RC3U V LAD4RC3N V LA4DA2E V LA4DA2G V LA4DA2U V LA4DA2N Table 18.24: Varistor (Peak Limiting) for Redution of Eletrial Noise in AC Contator Coils Installed by Mounting on Operating Voltage 50/60 Hz Snapping into the avity on the right side without toolsm Snap-on mounting, and onnetion without tools to the ontator oil terminals Srew onnetion to the ontator oil terminals LC D09 to D32 TeSys D ontators LC1D40A to LC1D65A (3P), LC1DT60A to LC1DT80A (4P) LC D80 to D115 (3P or 4P) LC D12, D25 (4P) Srew onnetion to the ontator oil terminals LC D80 (3P or 4P) Table 18.25: Diode for Redution of Eletrial Noise in DC Contator Coils V LAD4VE V LAD4VG V LAD4VU V LAD4V3E V LAD4V3G V LAD4V3U Va LA4DE2E Va LA4DE2G Va LA4DE2U Vd LA4DE3E Vd LA4DE3G Vd LA4DE3U Installed on the upper part by Mounting on Operating Voltage, DC Snap-on mounting and onnetion w/o tools to the ontator oil terminals LC D09 D Vd LAD4DDL Clip-on front mounting LC D40A to D65, D65A to DT80A Vd LAD4D3U Srew onnetion of wire to the ontator oil terminals D80 (3P) D80 (4P) Vd LA4DC3U Table 18.26: Bidiretional Peak Limiting Diode Installed by Mounting on Operating Voltage 50/60 Hz and DC Snapping into the avity on the right side of the ontator m LC D09 to LC D32 (3P)n 24 (AC only) LAD4TB DT20 to DT40 (4P) 72 (AC only) LAD4TS V LAD4T3B Clip-on front mounting and onnetion without tools LC1D40A to LC1D65A (3P), V LAD4T3S to the ontator oil terminals n LC1DT60A to LC1DT80A V LAD4T3G (4P) V LAD4T3U V LAD4T3R (AC only) LA4DB2B Srew mounting o LC D80 72 (AC only) LA4DB2S (DC only) LA4DB3B (DC only) LA4DB3S m Installing the suppressor into the avity makes the eletrial onnetion. Overall width of the ontator remains the same. n For LC D09 LC D65A with DC or low onsumption DC oils, 3-pole ontators are fitted with built-in bidiretional diode suppression as standard. o Mounting at the top of the ontator on oil terminals A1 and A2. Table 18.27: Cabling Aessories Usage Mounting on Operating Voltage 50/60 Hz For adapting existing wiring to a new produt or for use with top-mounting aessory. For adapting existing wiring to a new produt or for use with top-mounting aessory LC1D09 to D38 LC1DT20 to DT60 AC only LC1D40A to LC1D65A (with no oil suppressor) Without oil suppression LAD4BB With oil V LAD4BBVE suppression V LAD4BBVG (varistor) V LAD4BBVU LAD4BB Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

10 Contator Aessories TeSys D Eletroni Timers and Interfae Modules Refer to 8502CT The following aessories require use of abling aessories (LAD4BB ) for proper mounting. See page 18-9 for illustration. Table 18.28: Eletroni Serial Timer Modules These solid state modules delay the energizing of the ontator oil, and feature built-in varistor surge suppression. Operational Voltage a Type Va Va Time Delay s LA4DT0U 82. On-delay LC1D09 D65A LC1D80 D s LA4DT2U s LA4DT4U 82. a For 24 V operation, the ontator must be fitted with a 21 V oil: oil voltage ode Z5 for 50 Hz; Z6 for 60 Hz; and ZD for DC. Table 18.29: Interfae Modules b These modules allow the ontator oils to be energized from low voltage and low urrent level signals. They ome in mehanial relay and solid state versions. The relay plus manual operation versions inlude a lever for manually turning the ontator on and off. When a module reeives a low level signal, it allows the separate-soured ontrol voltage to flow to the ontator oil. It saves spae and wiring time ompared to onventional interposing relays. LA4DFB Interfae Type Operational Voltage Va Va Input Voltage Relay LC1D09 D Vd LA4DFB 55. LC1D09 D Vd LA4DFE 55. Relay Plus LC1D09 D Vd LA4DLB 71. Manual Operation LC1D09 D Vd LA4DLE 71. Solid State LC1D09 D65 LC1D80 D Vd LA4DWB 71. b Adapter required for D09 D65A, see table Table 18.30: Automati-Manual-Stop Control Modules These modules allow for loal and/or remote operation of the ontator oil. Eah module inludes a lever to swith from automati to manual operation and a dial to turn the ontator on and off. Operational Voltage Va Va LC1D09 D150 LA4DMK Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

11 Contator Aessories TeSys D and F Aessories Refer to 8502CT9901 LA9D3260 LAD92560 LA9D2561 LA9D80962 LA9D11567 Table 18.31: For Power Pole or Control Connetion Connetors for larger able sizes Everlink terminal blok Links for the parallel onnetion of: Desription For use with ontators LC1/LP1 Sold in lots of eah 4 poles #8 AWG (10 mm 2 ) D09, D12 1 LAD poles #4 AWG (25 mm 2 ) D09 D32 1 LA9D poles D40A D65A 1 LAD poles 3 poles (wye-delta shorting strap) 4 poles D09 D32 10 LA9D D40A D65A 1 LAD9P D80 2 LA9D F115 4 LA9FF F150, F185 4 LA9FG F265, F330, F400 4 LA9FH F500 4 LA9FK F630, F800 4 LA9FL D09 D32 10 LAD9P D40A-D65A 1 LAD9P D80 1 LA9D F115 1 LA9FF F150, F185 1 LA9FG F265, F330, F400 1 LA9FH F500 1 LA9FK F630, F800 1 LA9FL DT20, DT25 2 LA9D D80 2 LA9D Seond oil onnetion LP1D40 D80 10 LA9D Control iruit take-off from main pole D115, D LA9D D80 10 LA9D Spreaders for inreasing pole pith to 45 mm D115, D150 3 GV7AC Replaement power terminal blok D115, D150 1 LA9D Table 18.32: For Marking Desription For use with ontators LC1/LP1 Sold in lots of eah Referene label holder snap-on 8 x 22 mm 4-pole ontators D80 D LA9D92.06 Referene label holder snap-on 8 x 18 mm 3 poles D09-D65A, DT20-DT80A, LADN, LADT, LADR 100 LAD90.06 Sheet of 300 labels self adhesive 7 x 21 mm For holder LA9D92 1 LA9D Table 18.33: For Mounting Desription For use with ontators LC1/LP1 Sold in lots of eah Set of shims for mounting LAD8N and LA8DN D80 1 LA9D Retrofit plate for replaement of LC1D40-D65 with LC1D40A-D65A D40A-D65A 1 LAD7X mm DIN Rail 2 meters long LC1D09 to D80 10 AM1DP Table 18.34: Replaement Contats For use with ontators LC1D115 3 poles LA5D Three-pole LC1D150 3 poles LA5D Four-pole LC1D115 4 poles LA5D Table 18.35: Ar Chambers For use with ontators LC1D115 3 poles LA5D Three-pole LC1D150 3 poles LA5D Four-pole LC1D115 4 poles LA5D TeSys D ontators pages 18-4, 18-6 TeSys D overload relay aessories page TeSys D replaement oils pages to Dimensions pages to TeSys F ontators pages 18-5, 18-7 TeSys F replaement oils and parts pages 18-13, 18-18, LA9D Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

12 Contator Aessories LA9F980 LA9D09981 Table 18.36: Suppressor Bloks TeSys F Contators Refer to 8502CT Operating limit: up to 220 V, 50/60 Hz oils Desription For Use Suppressor blok With oils LX1FF, FG, FH, F115, F150, F185, F225, F265, F330 LA9F (lip-on mounting to oil) With oils LX1FJ, FK, FL, FX, F400, F500, F630, F780, LX9FF, FG, FH, F115, F150, F185, F225, F265, F330 LA9D Mounting braket (for 35 mm DIN rail or panel mounting) for suppressor blok LA9D Table 18.37: Lugs and Lug Kits a Contator Type LC1 Lug Kit Contator Only Cable Size AWG range Overload Relay Diretly mounted to ontator Lugs Required Cable size AWG range LC1 Line side of ontator Load side of overload Line side of ontator Load side of overload F115 DZ2FF6 14 to 2/0 LR9F5 57 to F5 69 F115 3 eah DZ2FF1 3 eah DZ2FG1 14 to 2/0 6 to 3/0 F150, F185 DZ2FG6 6 to 3/0 LR9F5 57 to F5 71 F150 to F185 1 eah DZ2FG6 6 to 3/0 LR9F5 71 F225, F265 1 eah DZ2FH6 6 to 300 MCM F225, F265, DZ2FH6 F330 6 to 300 MCM LR9F7 75 to F7 79 F265 or F330 3 eah DZ2FH1 6 to 300 MCM 4 to 500 MCM F400 DZ2FJ6 4 to 500 MCM LR9F7 75 to F7 81 F400 3 eah DZ2FJ1 4 to 500 MCM 4 to 500 MCM F500 DZ2FK6 2 x 2 to 600 MCM LR9F7 75 to F7 81 F500 3 eah DZ2FK1 2x2 to 600 MCM 4 to 500 MCM F630, F800 DZ2FL6 3 x 2 to 600 MCM LR9F7 81 F630 1 eah DZ2FL1 DZ2FL2 1 eah DZ2FR1 3x2 to 600 MCM 4 to 500 MCM DZ2FL3 F780 DZ2FX6 4 x 1/0 to 750 MCM a Lug kits ending in the number 6 inlude 6 idential lugs. In some ases the LR9F overload relay mounted diretly on the load side of an LC1F ontator will require a different size lug for your hoie of ontator and overload. If the two sizes are different, order 3 of eah size lug. Mounting hardware (srews, washers, and nuts) are provided with the ontators and overload relays, not with the lugs. See Table for priing. Table 18.38: Lugs, 2- and 4-Pole b Contator Type LC1 Lug Kit Qty. Required AL/CU Cable Size F115 DZ2FF to 2/0 F150, F185 DZ2FG to 3/0 F225, F265, F330 DZ2FH to 300 MCM F400 DZ2FJ to 500 MCM F500 DZ2FK X 2 to 600 MCM F630 DZ2FLb b b 3 X 2 to 600 MCM F780 DZ2FX X 1/0 to 750 MCM For 2-pole F630 ontators, order two DZ2FL1 (L1 and T2), and two DZ2FL3 (L2 and T1). For 4-pole F6304, order two DZ2FL1 (L1 and T4), four DZ2FL2 (L2, T2, L3, T3) and two DZ2FL3 (L4 and T1). Lugs for LC1F ontators and overload relays must be ordered separately. Eah kit onsists of one lug. Mounting hardware (srews, washers, nuts) are provided with the ontators, not the lugs. See Table for priing. Table 18.39: Lugs Priing Lug Lug DZ2FF DZ2FH DZ2FG DZ2FJ DZ2FH DZ2FK DZ2FJ DZ2FL DZ2FK DZ2FL DZ2FL DZ2FL DZ2FX DZ2FR DZ2FF DZ2FX DZ2FG These lear plasti protetive shrouds are an effetive means to meet international touh-safe requirements for power terminals. They are designed to be used with power ables that have been bolted to the terminal. NOTE: The protetion shrouds do not attah to ontators or overloads using DZ2F lug kits. 2-Pole 4-Pole LA9F70 Table 18.40: Power Terminal Protetion Shrouds For Use With 2-, 3-, And 4-pole Contators of Shrouds Per Set LC1F115 6 LA9F LC1F150, F185 6 LA9F LC1F225, F265, F330, F400 and F4002, F500 and F LA9F LC1F630, F6302 and F800 6 LA9F LC1F LA9F LC1F1504 and F LA9F LC1F2254, F2654, F3304, F4004, F LA9F LC1F LA9F For ontators LC1F115, LC1F150, and LC1F185, an available touh-safe terminal blok may be used in plae of lugs for power onnetions. Table 18.41: Insulated Terminal Bloks For ontator type LC1 For overload relay LR9 Maximum Cable Size F115, F150, F185 F5 57, F5 63, F5 67, F MCM LA9F TeSys F ontators pages 18-5, 18-7 TeSys F overload relay aessories page TeSys F replaement oils and parts pages 18-18, 18-18, Dimensions pages to Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

13 Replaement Parts TeSys F Contat Kits, Ar Chambers Refer to 8502CT9901 LA5FG431 LA5F11550 Table 18.42: Replaement Contat Sets a Two-pole Three-pole Four-pole Table 18.43: Ar Chambers a b d For use on ontators NUmber of Poles LC1F poles LA5F LC1F poles LA5F LC1F poles LA5F LC1F115, F150 3 poles LA5FF LC1F185 3 poles LA5FG LC1F265 3 poles LA5FH LC1F330, F400 3 poles LA5F LC1F500 3 poles LA5F LC1F630 3 poles LA5F LC1F780 1 pole LA5F780801d LC1F800 3 poles LA5F LC1F1504, F poles LA5FF LC1F poles LA5FG LC1F poles LA5FH LC1F3304, F400, F poles LA5F LC1F poles LA5F LC1F poles LA5F LC1F pole LA5F780801d For use on ontators of Poles LC1F poles LA5F Two-pole LC1F poles LA5F LC1F poles LA5F LC1F115 3 poles LA5F LC1F150 3 poles LA5F LC1F185 3 poles LA5F LC1F265 3 poles LA5F Three-pole LC1F330 3 poles LA5F LC1F400 3 poles LA5F LC1F500 3 poles LA5F LC1F630 3 poles LA5F LC1F780 1 pole LA5F780150d 431. LC1F800 3 poles LA5F LC1F poles LA5F LC1F poles LA5F LC1F poles LA5F LC1F poles LA5F Four-pole LC1F poles LA5F LC1F poles LA5F LC1F poles LA5F LC1F poles LA5F630450b 861. LC1F pole LA5F780150d 431. Supplied per pole are: 2 fixed ontats, 1 moving ontat, 2 defletors, 1 bakplate, mounting srews and washers. Comprises single-pole omponents. Comprises 2-pole omponents. 2 idential omponents per pole are supplied. TeSys F ontators pages 18-5, 18-7 TeSys F overload relay aessories page TeSys F replaement oils and parts pages 18-13, 18-18, Dimensions pages to Table 18.44: AC and DC Coil Part s for LC1F1700 and LC1F2100 Note: Control Ciruit Voltage of the Contator Voltage Code Spare Coil Part Quantity AC Coils 110 V F7 LX1FK V G7 LX1FK V M7 LX1FK V P7 LX1FK V U7 LX1FK V W7 LX1FK V Q7 LX1FK V V7 LX1FK V N7 LX1FK V R7 LX1FK V S7 LX1FK240 2 DC Coils 110 V FD LX4FK V GD LX4FK V MD LX4FK V UD LX4FK V RD LX4FK220 2 These oills are standard parts inluded when a voltage ode is added to the ontator part number LC1F1700 or LC1F Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

14 Contators Aessories TeSys D Reversing Contators Refer to 8502CT Table 18.45: Contators Reversing ontators omprising two idential, horizontally mounted ontators: Without eletrial interlok Mehanial interlok With inorporated eletrial interlok (2 N.C. ontats) Reversing ontators for motor ontrol Set of power onnetions Four pole ontators LC1D09, LC1D12, LC1D18, LC1D25, LC1D32 LAD9R1a LAD9R1Va Inluded with kit LC1DT20, LC1DT25, LC1DT32, LC1DT40 LADT9R1a LADT9R1Va Inluded with kit a Kit inluding mehanial interlok and wiring. LC1D40, LC1D50, LC1D/LP1D65 LA9D LA9D LA9D LA9D LC1D40A, D50A, D65A LAD4CM LA9D65A LAD9R3 b b Kit ombines both LAD4CM and LA9D65A69 LC1D80 AC oil LA9D LA9D LA9D LA9D LC1D80 DC oil LA9D LA9D LA9D LA9D LC1D115 and LC1D150 Not Available LA9D LA9D LA9D11571 (3P) LA9D11570 (4P) (D115 only) TeSys D ontators pages 18-4, 18-6 TeSys D overload relay aessories page TeSys D replaement oils pages to Dimensions pages to Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

15 A1 A2 LA9F 970 LA9F 977 LA9FX970 1N 1L2 2L1 2L3 1L3 1L1 2L2 2N L1 L2 L3 N Transfer/Changeover Appliations Contator Aessories A1 A2 LA9F 976 L1 L2 L3 LA9F A1 A2 U V W Reversing (motors) Appliation A1 A2 TeSys F ontators pages 18-5, 18-7 TeSys F overload relay aessories page TeSys F replaement oils and parts pages to Dimensions pages to TeSys F Reversing Contators Refer to 8502CT9901 Table 18.46: Component Parts for the Assembly of F-Line 3-pole Reversing Contators With 2 Idential Contators a Horizontal Mounting Set of Power Connetions Mehanial Interlok Kit LC1F115 LA9FF LA9FF LC1F150 LA9F LA9FF LC1F185 LA9FG LA9FG LC1F265 LA9FH LA9FJ LC1F330 LA9FJ LA9FJ LC1F400 LA9FJ LA9FJ LC1F500 LA9FK LA9FJ LC1F630 or F800 LA9FL LA9FL Vertial Mounting LC1F115 or F150 d LA9FF4F LC1F185 d LA9FG4G LC1F265 d LA9FH4H LC1F330 d LA9FJ4J LC1F400 d LA9FJ4J LC1F500 d LA9FK4K LC1F630 or F800 d LA9FL4L LC1F780 b LA9FX970 b Table 18.47: Component Parts for the Assembly of TeSys F 3-pole or 4-pole Transfer Contators Set of Power Connetions Mehanial Horizontal Mounting Interlok Kit Three-Pole Four-Pole Horizontal Mounting LC1F115/4 LA9FF982 LA9FF LA9FF LC1F150/4 LA9F15082 LA9F LA9FF LC1F185/4 LA9FG982 LA9FG LA9FG LC1F265/4 LA9FH982 LA9FH LA9FJ LC1F330/4 LA9FJ982 LA9FJ LA9FJ LC1F400/4 LA9FJ982 LA9FJ LA9FJ LC1F500/4 LA9FK982 LA9FK LA9FJ LC1F630/4 LA9FL982 LA9FL LA9FL Vertial Mounting LC1F115/4 d d LA9FF4F LC1F185/4 d d LA9FG4G LC1F265/4 d d LA9FH4H LC1F330/4 d d LA9FJ4J LC1F400/4 d d LA9FJ4J LC1F500/4 d d LA9FK4K LC1F630/4 d d LA9FL4L LC1F780/4 b LA9FX Table 18.48: Vertial Mounting of 2 Contators of Different Ratings a Upper Contator Lower Contator e Mehanial Interlok Kit LC1F185 or 1854 LC1F115/150 or 1154/1504 LA9FG4F LC1F265 or 2654 LC1F115/150 or 1154/1504 LA9FH4F LC1F330 or 3304 LC1F185/1854 or 265/265A LA9FH4G LC1F115/150 or 1154/1504 LA9FJ4F LC1F400 or 4004 LC1F185 or 1854 LA9FJ4G LC1F265/2654 or 330/330A LA9FJ4H LC1F115/150 or 1154/1504 LA9FK4F LC1F500 or 5004 LC1F185 or 1854 LA9FK4G LC1F265/2654 or 330/330A LA9FK4H LC1F400 or 4004 LA9FK4J LC1F630, 6304 or LC1F800 LC1F115/150 or 1154/1504 LA9FL4F LC1F185 or 1854 LA9FL4G LC1F265/2654 or 330/330A LA9FL4H LC1F400 or 4004 LA9FL4J LC1F500 or 5004 LA9FL4K a With idential or different numbers of poles. b Double mehanial interlok with 2 mehanial links and 3 power onnetion bars. Double mehanial interlok with 2 mehanial links and 4 power onnetion bars. d Power onnetion to be assembled by the ustomer, exept for ontators LC1F780 and F7804. e Lower ontator must have equal or lower urrent rating Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

16 Overload Relays LA7D901 LA9F70 LA7D03 LA7F90 LA7F701 TeSys D Overload Relay Aessories Table 18.49: Mounting Kits and Platesa TeSys F Overload Relay Aessories TeSys D and F Overload Relay Aessories Refer to 8502CT Desription For use with overload relays: Separate mounting kits for mounting to 35 mm DIN rail or for panel mounting with srews Mounting plates for srew mounting at 110 mm (4.3 in.) enters a When using mounting plates, separate mounting kits are also required. Table 18.50: Aessories Desription LRD01 35 and LR3D01 35 LAD7B LRD01 35 and LRD01 35 for ring tongue terminals LAD7B LRD15 LAD7B LR2D15, LR3D15 LA7D LR2D25 LA7D LRD3, LR3D3, LR2D35 LA7D LRD01 35, LR3D01 35, LR2D15 DX1AP LR2D25 DX1AP LRD3, LR3D3, LR2D35 LA7D For use with Standard Pakaging Prewiring kit allows diret onnetion of the N.C. ontat LC1D09 through D18 10 LAD7C of relay LRD01 D32 or LR3D01 D32 to the ontator LC1D25, D32 10 LAD7C Stop button loking devie All relays exept LRD01 D32, LR3D01 D32 and LR9D 10 LA7D Remote stop/tripping or eletrial reset LRD01-D32, LRD3, LR3D01-D32, LR3D3 1 LAD703b All relays exept LRD01 D32, LR3D01 D31 1 LA7D03b Reset by flexible able 500 mm (19.6 in.) LRD01-D32, LRD3, LR3D3 1 LAD b Part number to be ompleted by adding oil voltage ode, (for example, LAD703F). Table 18.51: Control Ciruit Voltages for LA7D03 and LAD703 Volts / / /440 AC 50/60 Hz Jd B E F M Q N DC J B E F M The time that the LA7D03 an remain energized depends on its rest time; 1 s pulse with 9 s rest time; 5 s pulse with 30 s rest time; 10 s pulse with 90 s rest time; maximum pulse duration of 20 s with rest time of 300 s. Consumption on inrush and sealed: < 100 VA d Not available for LRD01 D32, LR3D01 D32. Table 18.52: Mounting Plate for Overload Relay For use with relays LR9F5 57, F5 63, F5 67, F5 69 and F5 71 LA7F LR9F7 75, F7 79 and F7 81 LA7F These lear plasti protetive shrouds are an effetive means to meet international finger-safe requirements for power terminals. They are designed to be used with power ables that have been bolted to the terminal. NOTE: The protetion shrouds do not attah to ontators or overloads utilizing DZ2F lug kits. Table 18.53: Power Terminal Protetion Shrouds, Single-Pole For use with relays LR9F5 57 LA9F LR9F5 63, F5t67, F5 69 LA9F LR9F5 71 LA9F LR9F7 75, F7 79, F7 81 LA9F Table 18.54: Power Terminal Protetion Shrouds, 3-Pole For use with relays LR9F5 57, F5 63, F5 67, F5 69 LA7F LR9F5 71 LA7F LR9F7 75, F7 79, F7 81 LA7F Table 18.55: Connetion Aessories (for Mounting Overload Relays Beneath Reversing Contators)e Appliation Set of 3 Bars For relays For ontator LR9F5 57, F5 63, F5 67, F5 69 LC1F115 LA7F LR9F5 57, F5t63 LC1F150 and F185 LA7F LR9F5 71 LC1F265 LA7F LR9F7 75, F7 79 LC1F265...F400 LA7F LR9F7 81 LC1F400 LA7F LR9F7 75, F7 79, F7 81 LC1F500 LA7F LR9F7 81 LC1F630 LA7F e Mounting plate required. Table 18.56: Marking Aessories Desription Sold in units of: Marker holder, snap-in 100 LA7D eah Main overload seletion pages 18-2, 18-3 Dimensions pages to TeSys T pages Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

17 LX1D2 Contator Repair Parts Table 18.57: For LC1D09 D32, LC1DT20 40 (TeSys D) Contators and CAD Relays Rated Nominal Voltage 50/60 Hz 12 LXD1J7 21a LXD1Z7 24 LXD1B LXD1C7 36 LXD1CC7 42 LXD1D7 48 LXD1E7 60 LXD1EE LXD1K7 110 LXD1F7 115 LXD1FE7 120 LXD1G7 127 LXD1FC LXD1L7 208 LXD1LE7 220/230 LXD1M7 230 LXD1P7 230/240 LXD1U LXD1W7 380/400 LXD1Q7 400 LXD1V7 415 LXD1N7 440 LXD1R LXD1T7 575 LXD1SC7 600 LXD1X Speifiations 50/60 Hz Average onsumption - Inrush (indutane 0.75) 70 VA - Sealed (indutane 0.3) 7 VA Operating range@ 60 o % of 50 Hz, C % of 60 Hz a Voltage for speial oils fitted in ontators with serial timer modules, with 24 V supply. Limited Stok Replaed by TeSys Produts TeSys D and Old D2 AC Coils Refer to 8502CT9901 Table 18.58: For LC1D09, D12, D18 For old D2 style ontators where the atalog number inludes the auxiliary ontat arrangement Rated Nominal Voltage V 50 Hz 60 Hz 50/60 Hz 21 b LX1D2Z5 LX1D2Z6 LX1D2Z7 24 LX1D2B5 LX1D2B6 LX1D2B7 32 LX1D2C5 42 LX1D2D5 LX1D2D7 48 LX1D2E5 LX1D2E6 LX1D2E7 110 LX1D2F5 LX1D2F6 LX1D2F7 120 LX1D2G6 LX1D2G7 127 LX1D2G5 208 LX1D2L6 220 LX1D2M5 LX1D2M6 LX1D2M7 230 LX1D2P5 LX1D2P7 240 LX1D2U5 LX1D2U6 LX1D2U7 256 LX1D2W5 277 LX1D2W6 380 LX1D2Q5 LX1D2Q6 LX1D2Q7 400 LX1D2V5 LX1D2V7 415 LX1D2N5 LX1D2N7 440 LX1D2R5 LX1D2R6 LX1D2R7 480 LX1D2T6 500 LX1D2S5 575 LX1D2S6 600 LX1D2X6 660 LX1D2Y5 Limited Stok Replaed by TeSys Produts Speifiations 50 Hz 60 Hz 50/60 Hz Average onsumption Inrush (indutane.75) 60 VA 70 VA 70 VA at 50 or 60 Hz Sealed (indutane.3) Operating range at θ < 55 o C / 131 o F 7 VA 7.5 VA 8 VA at 50 or 60 Hz % of nominal voltage % of nominal voltage % of nominal voltage Table 18.59: For LC1D25, D32 For old D2 style ontators where the atalog number inludes the auxiliary ontat arrangement Rated Nominal Voltage (V) 50 Hz 60 Hz 50/60 Hz 21b LX1D4Z5 LX1D4Z6 LX1D4Z7 24 LX1D4B5 LX1D4B6 LX1D4B7 32 LX1D4C LX1D4D5 LX1D4D7 48 LX1D4E5 LX1D4E6 LX1D4E7 110 LX1D4F5 LX1D4F6 LX1D4F7 120 LX1D4G6 LX1D4G7 127 LX1D4G LX1D4L6 220 LX1D4M5 LX1D4M6 LX1D4M7 230 LX1D4P5 LX1D4P7 240 LX1D4U5 LX1D4U6 LX1D4U7 256 LX1D4W LX1D4W6 380 LX1D4Q5 LX1D4Q6 LX1D4Q7 400 LX1D4V5 LX1D4V7 415 LX1D4N5 LX1D4N7 440 LX1D4R5 LX1D4R6 LX1D4R LX1D4T6 500 LX1D4S5 575 LX1D4S6 600 LX1D4X LX1D4Y5 Speifiations 50 Hz 60 Hz 50/60 Hz Average onsumption - Inrush (indutane.75) - Sealed (indutane.3) 90 VA 7.5 VA 100 VA 8.5 VA Operating range % of % of at θ < 55 C / 131 F nominal voltage nominal voltage b For use in 24 V appliations involving serial timer modules refer to page VA at 50 or 60 Hz 8.5 VA at 50 or 60 Hz % of nominal voltage TeSys D ontators pages 18-4, 18-6 TeSys D overload relay aessories page TeSys D replaement oils pages to Dimensions pages to Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

18 Contator Repair Parts TeSys D, Old D2, and F AC Coils Refer to 8502CT Table 18.60: For Old D2 Style LC1D40, D50, D65, D80 Rated Nominal Voltage V 50 Hz LX1D6 60 Hz 50/60 Hz Table 18.61: For TeSys D LC1D40A, D50A, D65A, DT60A, DT80A Rated Nominal Voltage V 50 Hz 60 Hz 50/60 Hz Table 18.62: For TeSys D LC1D115, D150 Rated Nominal Voltage V 50 Hz 60 Hz 50/60 Hz 24 LX1D6B5 LX1D6B6 LX1D6B LXD3J LX1D8B5 LX1D8B6 LX1D8B LX1D6C LXD3B LX1D8C5 LX1D8C LX1D6D5 LX1D6D LXD3C LX1D8D5 LX1D8D LX1D6E5 LX1D6E6 LX1D6E LXD3D LX1D8E5 LX1D8E6 LX1D8E LX1D6F5 LX1D6F6 LX1D6F LXD3E LX1D8F5 LX1D8F6 LX1D8F LX1D6G6 LX1D6G LXD3K LX1D8FE5 LX1D8FE LX1D6G LXD3F LX1D8G6 LX1D8G LX1D6L6 LX1D6LE LXD3FE LX1D8FC5 LX1D8FC LX1D6M5 LX1D6M6 LX1D6M LXD3G LX1D8L6 LX1D8L LX1D6P5 LX1D6P LXD3FC /230 LX1D8M5 LX1D8M6 LX1D8M LX1D6U5 LX1D6U6 LX1D6U LXD3L LX1D8P5 LX1D8P LX1D6W LXD3LE LX1D8U5 LX1D8U6 LX1D8U LX1D6W LXD3M LX1D8W6 LX1D8W LX1D6Q5 LX1D6Q6 LX1D6Q LXD3P /400 LX1D8Q5 LX1D8Q6 LX1D8Q LX1D6V5 LX1D6V LXD3U LX1D8V5 LX1D8V LX1D6N5 LX1D6N LXD3W LX1D8N5 LX1D8N LX1D6R5 LX1D6R6 LX1D6R LXD3Q LX1D8R5 LX1D8R6 LX1D8R LX1D6T LXD3V LX1D8T6 LX1D8T LX1D6S LXD3N LX1D8S5 LX1D8S LX1D6S LXD3R LX1D6X LXD3T LX1D6Y LXD3S LXD3SC For old style and new TeSys style ontators where the atalog 600 LXD3X number may or may not inlude the auxiliary ontat arrangement. 660 LXD3YC LXD3Y For old style and new TeSys style ontators where the atalog number may or may not inlude the auxiliary ontat arrangement. Speifiation 50 Hz 60 Hz 50/60 Hz Speifiation 50 Hz 60 Hz 50/60 Hz Speifiation 50 Hz 60 Hz 50/60 Hz Average onsumption: -inrush (indutane 0.75) -sealed (indutane 0.3) Operating range at θ < 55 o C / 131 o F 200 VA 20 VA 220 VA 22 VA 245 VA 26 VA % of nominal voltage % of nominal voltage Average onsumption: -inrush (indutane 0.3) -sealed (indutane 0.3) Operating range at θ < 55 C / 131 F 160 VA 7.0 VA 140 VA 7.5 VA 140 VA (Indutane: 0.9) 7.5 VA (Indutane: 0.9) % of % of nominal voltage nominal voltage Average onsumption: -inrush (indutane 0.8) 300 VA -sealed (indutane 0.3) 22 VA 300 VA 22 VA 350 VA (Indutane: 0.9) 18 VA (Indutane: 0.9) Operating range at % of % of θ < 55 C / 131 F nominal voltage nominal voltage Table 18.63: For LC1F115, F150, F185, F265, F330, F400, F500, F630, F780, F800 LX1 oils are the standard oils that are inluded when a voltage ode is added to the ontator part number. The LX9 oils may be ordered separately for speial appliations. LX9 oils do not inlude a built-in normally open holding iruit ontat; a separate auxiliary ontat blok with a N.O. ontat should be added to the ontator. Both the LX1 and LX9 oils an be used on the previous F-line ontators. Devie Type F115 F150 F185 F225 F265 F330 F400d F500d F630d Hz Suffixg 24 V 48 V 110 V 120 V 208 V 220 V 240 V 277 V 380 V 415 V 440 V 480 V 600 V 50 LX1FF LX1FF LX9FF LX1FG LX1FG LX9FG LX1FH LX9FH LX1FJ LX9FJ f LX1FK LX9FK f LX1FL LX9FL f F780, FX LX1FX F800 50/60 LX4F8 e FW FW MW MW QW QW QW LC1F780 ontators operate on 2 oils as a set. The LX1FX part number inludes both oils. d The 600 V oils for the F400, F500 and F630 do not inlude an auxiliary ontat for holding iruits. If required, selet appropriate ontats from page e Also requires retifier DR5TE4U for V oils, DR5TE4S for V oils. See Table for priing. f Coil iruit requires a separately mounted retifier. Order from Table g Complete the atalog number by adding the suffix (for example, LX1FF024). Appliation Note on Contator Drop-out Times: Contators using LX1, FH, FJ, FK, FL, and FX oils have longer drop-out times. For ritial appliations suh as emergeny stop funtions: Selet a fast drop-out oil (LX9), or Use a maintained ontat Stop button, or Use an interposing relay. TeSys D ontators pages 18-4, 18-6 TeSys F ontators pages 18-5, 18-7 TeSys D overload relay aessories page TeSys D replaement oils pages to Dimensions pages to Table 18.64: Retifier Table Coil Retifier LX9F 910 DR5TF4V LX9F 917 DR5TF4V LX9F 925 DR5TE4U LX9F 926 DR5TE4U LX9F 931 DR5TE4U LX9F 936 DR5TE4S LX9F 937 DR5TE4S LX9F 938 DR5TE4S Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

19 Contator Repair Parts TeSys D, and Old D2 DC Coils Refer to 8502CT9901 Table 18.65: For Old D2 LP1D09, D12, D18 a Rated Nominal Voltage V Wide Range 12 LX4D2JD LX4D2JW b LX4D2ZD LX4D2BD LX4D2BW LX4D2CD LX4D2CW LX4D2ED LX4D2EW LX4D2ND LX4D2SD LX4D2SW LX4D2FD LX4D2FW LX4D2GD Limited Stok Replaed by TeSys Produts 220 LX4D2MD LX4D2MW LX4D2UD LX4D2RD LX4D2XD Table 18.67: For Old D2 LP1D40, D50, D65 a Rated Nominal Voltage V Wide Range 12 LX4D6JD LX4D6JW 24 LX4D6BD LX4D6BW 36 LX4D6CD LX4D6CW 48 LX4D6ED LX4D6EW 60 LX4D6ND 72 LX4D6SD LX4D6SW 110 LX4D6FD LX4D6FW 125 LX4D6GD 220 LX4D6MD LX4D6MW 250 LX4D6UD Limited Stok Replaed by TeSys Produts 440 LX4D6RD 600 LX4D6XD Speifiations Average onsumption 9 W 11 W Operating range at θ 55 C / 131 F % of nominal voltage Table 18.66: For Old D2 LP1D25, D32 a Rated Nominal Voltage V Wide Range % of nominal voltage 12 LX4D4JD LX4D4JW b LX4D4ZD LX4D4BD LX4D4BW LX4D4CD LX4D4CW LX4D4ED LX4D4EW LX4D4ND LX4D4SD LX4D4SW LX4D4FD LX4D4FW LX4D4GD Limited Stok Replaed by TeSys Produts 220 LX4D4MD LX4D4MW LX4D4UD LX4D4RD LX4D4XD Speifiations Average onsumption 11 W 13 W Operating range at θ < 55 C / 131 F % of nominal voltage % of nominal voltage a For old style ontators where the atalog number inludes the auxiliary ontat arrangement (for example, LP1D2510). The new style TeSys DC ontrolled ontators (for example, LC1D25BD) do not have replaeable oils. b For use in 24 V appliations with serial timer modules. Refer to page No replaement DC oils for TeSys D ontators. TeSys DC Coil Speifiations Average onsumption Operating range LC1D09-D32, Inrush 5.4 W LC1DT20 LC1DT40 Sealed 5.4 W o C LCID A Inrush 19 W Sealed 7.4 W o C Low onsumption LC1D09-D32, Inrush 2.4 W LC1DT20 LC1DT40 Sealed 2.4 W o C Note: DC oils for LC1D09 D32, LC1DT20 LC1DT40, and LCID A ontators are not replaeable. Speifiations Average onsumption 22 W 23 W Operating range at θ < 55 C /131 F % of nominal voltage % of nominal voltage Table 18.68: For Old D2 LP1D80 and LC1D80a Rated Nominal Voltage V Wide Range d 12 LX4D7JD LX4D7JW 24 LX4D7BD LX4D7BW 36 LX4D7CD LX4D7CW 48 LX4D7ED LX4D7EW 60 LX4D7ND 72 LX4D7SD LX4D7SW 110 LX4D7FD LX4D7FW 125 LX4D7GD 220 LX4D7MD LX4D7MW 250 LX4D7UD 440 LX4D7RD 600 LX4D7XD Speifiations Average onsumption 22 W 23 W Operating range at θ < 55 C / 131 F % nominal voltage % nominal voltage d Wide range oils annot be used with ontators using both front- and side-mounting auxiliaries. Table 18.69: For TeSys D LC1D115, 150 Rated Nominal Voltage V 24 LX4D8BD 48 LX4D8ED 60 LX4D8ND 72 LX4D8SD 110 LX4D8FD 125 LX4D8GD 220 LX4D8MD 250 LX4D8UD 440 LX4D8RD Average Consumption Operating range at θ < 55 C / 131 F Inrush 365 W, Sealed 5 W 70% 120% of nominal voltage TeSys D ontators pages 18-4, 18-6 TeSys D overload relay aessories page TeSys D replaement oils pages to Dimensions pages to Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

20 Contator Repair Parts TeSys F DC Coils Refer to 8502CT TeSys F DC Coils LX4 oils are the standard oils when a voltage ode is added to the part number. The LX9 oils may be ordered separately for speial appliations. LX9 oils do not inlude a built-in normally open holding iruit ontat; a separate auxiliary ontat blok with a N.O. ontat should be added to the ontator. Both the LX4 and LX9 oils an be used on previous F-line devies. Table 18.70: LX4 Coils for LC1F115, F150, F185, F265, F400, F500, F630, F780, F800 Devie Type TeSys F ontators pages 18-5, 18-7 TeSys F overload relay aessories page TeSys F replaement oils and parts pages 18-18, 18-18, Dimensions pages to Suffix 24 V 36V 48 V 60 V 72 V 110 V 125 V 220 V 250 V 440 V F115, F150 LX4FF F185, F225 LX4FG F265, F330 LX4FH F400 F500 F630 LX4FJ LX9FJ LX4FK LX9FK LX4FL LX9FK F780 LX4FX a F800 LX4F8 b FW FW MW QW a LC1F780 ontators operate on 2 oils as a set. The LX4FX part number inludes both oils. b Also requires retifier DR5TE4U, $72.00 list prie. Coil iruit requires a separately mounted resistor. Order from Table below. Table 18.71: LX9 Coils and Resistors Coil Resistor Qty. Required Coil Resistor Qty. Required Coil Resistor Qty. Required LX9FJ918 DR2SC LX9FK918 DR2SC LX9FL918 DR2SC LX9FJ926 DR2SC LX9FK926 DR2SC LX9FL925 DR2SC LX9FJ927 DR2SC LX9FK927 DR2SC LX9FL926 DR2SC LX9FJ932 DR2SC LX9FK932 DR2SC LX9FL931 DR2SC LX9FJ938 DR2SC LX9FK938 DR2SC LX9FL937 DR2SC Shneider Eletri I12 Disount This doument provided by Barr-Thorp Eletri Co., In

21 Enlosed Starters TeSys D in Metal Enlosures Refer to 8502CT9901 TeSys D enlosed full-voltage starters are available in Type 1 and Type 12/3R enlosures through 50 hp at 460 V. The enlosed D-line aepts standard D-Line aessories and all Insta-Kits ontrol units and ontrol power transformer kits. Standard apaity ontrol power transformers with built-in fuse blok an be installed in the standard enlosure. For extra apaity, please refer to your loal distributor or Shneider Eletri sales offie. Table 18.72: Enlosed Full Voltage Non-Reversing Starters Max. Horsepower Ratings (AC3) 1 Phase 3 Phase Auxiliary Contats Current Rating of Contator V 230 V 460 V 575V N.O. N.C. Type 1 Type 12/3R LE1D093A LE1D093A LE1D123A LE1D123A LE1D183A LE1D183A LE1D253A LE1D253A LE1D323A LE1D323A LE1D403A LE1D403A LE1D503A LE1D503A LE1D653A LE1D653A LE1D803A LE1D803A Table 18.73: Enlosed Full Voltage Reversing Starters Max. Horsepower Ratings (AC3) 3 Phase Auxiliary Contats On Eah Contator Current Rating of Contator 200V 230 V 460 V 575 V N.O. N.C. Type 1 Type 12/3R LE2D093A LE2D093A LE2D123A LE2D123A LE2D183A LE2D183A LE2D253A LE2D253A LE2D323A LE2D323A LE2D403A LE2D403A LE2D503A LE2D503A LE2D653A LE2D653A LE2D803A LE2D803A Table 18.74: Nomenlature Example: Wiring Method Control Power Transformer f Contator/Starter Coil Voltage g Coil Frequeny h Overload Relay Type j Overload Relay Range i fcontrol Power Transformer Add prie from page Selet letter for primary voltage of CPT: Voltage No Transformer used Code O a L M T X a Letter O, not zero. Note: If ontrol transformer is used, the only options available are 24 or 120 V as the seondary of the transformer. Also, DC voltages are not available when ontrol power transformer is used. gcontator/starter Coil Voltage Selet oil voltage from table: Voltage AC B G L U T X DC B hcoil Frequeny Selet: 7 dual frequeny oils (50/60 Hz.) 6 60 Hz. DDC Note: Base For 9 to 65 A ontators, only dual frequeny oils are available; 80 A ontators, the V oils are dual frequeny only (50/60 Hz.). The V oils are 60 Hz. only. See atalog 8502CT9901 for other restritions. joverload relay type LE1D093A62 O G Table 18.75: ioverload Relay Range (Selet ode from the table below) b Note: Code Range For use on Contators Adder D09 D32b D09 D32b D09 D32b D09 D32b D09 D32b D09 D32b D09 D32b D09 D D09 D D09 D D40, D50, D D09 D D12 D D40, D50, D D18 D D25 D32b D25 D D D40, D50, D D25 D D25 D D40, D50, D D40, D50, D D40, D50, D D D D D D65 D D65 D D40, D50, D Available for Class 10 only. Available for Class 20 only. If no overload relay is required, leave this portion of the atalog blank. Add appropriate prie adder to the base prie of the starter. Dimensions page Selet: 0 No overload relay 1 Class 10 Trip 2 Class 20 Trip 2012 Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

22 Enlosed Combination Starters TeSys D Fusible Disonnet Swith or Ciruit Breaker Refer to 8502CT IEC ombination starters ombine the requirements of motor overload and short iruit protetion in one onvenient ompat pakage. All devies provide Type 2 Coordination through 30 hp at 460 V. Devies are available in Type 1 and Type 12/3R enlosures. The IEC ombination starter line aepts standard TeSys D aessories and all Insta-Kits pilot devies and ontrol power transformer kits. Standard apaity ontrol power transformers with built-in fuse blok an be installed in the standard enlosure. For extra apaity, please refer to your loal distributor or nearest Square D/Shneider Eletri sales offie. NOTE: Use tables and notes from page to omplete the atalog numbers. Table 18.76: Enlosed Full Voltage Non-Reversing Fusible Combination Starters Max. Horsepower Ratings (AC3) Fuse Clip Rating Auxiliary Current 3 Phase Contats Rating of 200 V 230 V 460 V 575 V Amperes UL Class N.O. N.C. Contator Type 1 Type 12/3R A CC LE1D096B LE1D096B A CC LE1D126B LE1D126B A J LE1D186B LE1D186B A J LE1D256B LE1D256B A J LE1D326C LE1D326C A J LE1D406C LE1D406C Table 18.77: Enlosed Full Voltage Reversing Fusible Combination Starters Max. Horsepower Ratings (AC3) Aux. Contats Fuse Clip Rating Current 3 Phase Eah Contator Rating of 200 V 230 V 460 V 575 V Amperes UL Class N.O. N.C. Contator Type 1 Type 12/3R A CC LE2D096B LE2D096B A CC LE2D126B LE2D126B A J LE2D186B LE2D186B A J LE2D256B LE2D256B A J LE2D326C LE2D326C A J LE2D406C LE2D406C Table 18.78: Enlosed Full Voltage Non-Reversing Ciruit Breaker Combination Starters Max. Horsepower Ratings (AC3) Auxiliary Ciruit Breaker Current Contats 3 Phase Maximum Rating of 200 V 230 V 460 V 575 V N.O. N.C. Current Rating Contator Type 1 Type 12/3R A 9 LE1D097D LE1D097D A 12 LE1D127D LE1D127D A 18 LE1D187E LE1D187E A 25 LE1D257E LE1D257E A 32 LE1D327F LE1D327F A 40 LE1D407F LE1D407F Table 18.79: Enlosed Full Voltage Reversing Ciruit Breaker Combination Starters Max. Horsepower Ratings (AC3) Auxiliary Contats Ciruit Breaker Current 3 Phase Eah Contator Maximum Rating of 200 V 230 V 460 V 575 V N.O. N.C. Current Rating Contator Type 1 Type 12/3R A 9 LE2D097D LE2D097D A 12 LE2D127D LE2D127D A 18 LE2D187E LE2D187E A 25 LE2D257E LE2D257E A 32 LE2D327F LE2D327F A 40 LE2D407F LE2D407F Table 18.80: Enlosed Full Voltage Non-Reversing Non-Fused Combination Starters Max. Horsepower Ratings (AC3) Auxiliary Current 3 Phase Contats Rating of 200 V 230 V 460 V 575 V N.O. N.C. Contator Type 1 Type 12/3R LE1D096A LE1D096A LE1D126A LE1D126A LE1D186A LE1D186A LE1D256A LE1D256A LE1D326A LE1D326A LE1D406A LE1D406A Table 18.81: Enlosed Full Voltage Reversing Non-Fused Combination Starters Max. Horsepower Ratings (AC3) Aux. Contats Current 3 Phase Eah Contator Rating of 200 V 230 V 460 V 575 V N.O. N.C. Contator Type 1 Type 12/3R LE2D096A LE2D096A LE2D126A LE2D126A LE2D186A LE2D186A LE2D256A LE2D256A LE2D326A LE2D326A LE2D406A LE2D406A Dimensions page Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

23 B F A L1 START STOP A B M L1 OFF ON X1 X A PL M B L Enlosed Combination Starters OLR X1 X2 PL OFF HAND AUTO 3 4 B M A Start/Stop On-Off Seletor Swith X1 X2 PL M X1 OLR PL X2 L2 L2 L2 Remote by Customer Connetion HOA Seletor Swith L1 L2 L3 T1 T2 T3 D-Line AC Magneti Starter 2-3 Poll L1 L2 L B R A Enlosure Modifiations/Insta-Kits /Overload Relay Refer to 8502CT9901 Fatory Modifiations and Insta-Kits Seletion Add the fatory modifiation ode to the end of the atalog number reated from page With the use of Insta-Kits, only one operator sheme is allowed. Only the ombinations of operators and pilot lights shown below an be ordered. Pilot lights will be at the oil voltage indiated in the atalog number for the starter. Table 18.82: Fatory Modifiations Desription Fatory Modifiation Codea Insta-Kits (for field installation) Control Units Only For-Rev-Stop Push Button A06L 131. LA9CA06LT Start/Stop Push Button A06G 65. LA9CA06GT I/O (Start/Stop) Push Button N/A N/A I/O Push Button (double touh) A06I 83. LA9CA06IO Emergeny Stop N/A N/A Hand-Off-Auto Seletor Swith A06E 65. LA9CA06ET On/Off Seletor Swith A06D 65. LA9CA06DT Start/Mushroom Head Stop Push Button A06X 65. LA9CA06XT Pilot Lights only LED Pilot light, 24, 120 or 240 V A16S 134. LA9CA16STd Green-Red Pilot Light, Diret Supply, 24 or 120 V b A06S 112. LA9CA06STd Green-Red Transformer Pilot Light, 120, 208/240, 480 or 600 V b A06F 207. LA9CA06FTd Available Combination of Control Units and Pilot Lights Hand-Off-Auto Seletor Swith w/24, 120, or 240 V LED Pilot Light A16U 213. LA9CA16UTd Start/Stop Push Button w/ 24, 120 or 240 V LED Pilot Light A16V 213. LA9CA16VTd On/Off Seletor w/ 24, 120 or 240 V LED Pilot Light A16W 213. LA9CA16WTd Start/Stop Push Button w/ Green-Red Transformer Pilot Light A06N 177. LA9CA06NTd Start/Stop Push Button w/green-red Pilot Light A06V 177. LA9CA06VT Hand-Off-Auto Seletor Swith w/green-red Pilot Light A06U 273. LA9CA06UT Hand-Off-Auto Seletor Swith w/green-red Transformer Pilot Light A06J 273. LA9CA06JTd On/Off Seletor w/green-red Pilot Light A06W 177. LA9CA06WT On/Off Seletor w/green-red Transformer Pilot Light A06H 273. LA9CA06HTd Control Power Transformer Standard VA, 2 Fuses in Primary, 1 Fuse in Seondary A206P VA extra, 2 Fuses in Primary, 1 Fuse in Seondary A207P VA extra, 2 Fuses in Primary, 1 Fuse in Seondary A208P 634. a Add these forms to the atalog number seleted on page The numbers as shown are for use in NEMA 1 Enlosures. For uses in NEMA 12/3R hange the 6 to a 7 (ex A06U beomes A07U). Prie remains the same. The hange DOES NOT apply to ontrol power transformer forms. b Pilot lights are wired suh that the light is on when the ontator is energized. For non-led type pilot lights, a green lens is installed on the unit when shipped. A red lens is inluded for use as appliable. Selet Insta-Kits from table below. Table 18.83: Insta-Kits Seletion d Total VA Insta-Kits 50 LA9TFD32d LA9TFD80d LA9TFD15d Complete the part number for the Insta-Kits by seleting the voltage ode from the appropriate tables below. Table 18.84: Voltage Codes for Pilot Lights Voltage (Va) / Code B G M T X Table 18.85: Voltage Codes for Control Power Transformers Primary Voltage Seondary Voltage Code E D C B A L M T X "C" T1 T2 T3 D-Line AC Magneti Reversing Starter 3-Pole 2012 Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

24 Contators 3-Pole Non-Reversing Mini-Contators TeSys K 3-Pole Non-Reversing Contators Refer to 8502CT LC1K09 Table 18.86: AC Operating Coils Maximum Horsepower Ratings Maximum Current Auxiliary 1 Ø 3 Ø Type of Contats Indutive Resistive Connetion 115 V hp 230 V hp 200 V hp 230 V hp 460 V hp 575 V hp AC3 (A) AC1 (A) N.O. N.C Srew-lamp Srew-lamp Srew-lamp 1 LC1K0610 a b LC1K0601 ab LC1K0910 ab LC1K0901 ab LC1K1210 ab LC1K1201 ab 86. Table 18.87: Coil Voltage Codes for AC Contators Up to and inluding 240 V oil with integral suppression devie available. Add 2 to the ode required (for example, J72). Prie adder $ Va 50/60 Hz / / / / / Code J7 B7 D7 E7 F7 G7 FC7 L7 M7 P7 U7 UE7 Q7 N7 R7 T7 Y7 660/ 690 Table 18.88: DC Operating Coils Srew-lamp 1 LP1K0610 ab LP1K0601 ab Srew-lamp 1 LP1K0910 ab LP1K0901 ab Srew-lamp 1 LP1K1210 ab LP1K1201 ab 106. a See Table 18.89: For TeSys K ontators with spring terminal lamps, add a 3 before the oil voltage ode (for example, LC1K06103G7). For TeSys K ontators with solder pin terminals, add a 5 before the oil voltage ode (for example, LC1K09105B7). For TeSys K ontators with slip-on terminals, add a 7 before the oil voltage ode (for example, LC1K12107M7). b Complete the atalog number with the appropriate oil voltage ode (for example, LC1K0610G7). Table 18.89: Coil Voltage Codes for DC Contators Coil with integral suppression devie available. Add 3 to the ode required (for example, JD3). Prie adder $10.00 a a Vd Code JD ZD BD CD ED ND SD KD FD GD LD MD MPD MUD UD 3 W inrush. LP4K09, Table 18.90: DC Low Consumption Operating Coils (devies have built-in transient suppression) Srew-lamp 1 LP4K0610 ab LP4K0601 ab Srew-lamp 1 LP4K0910 ab LP4K0901 ab Srew-lamp 1 LP4K1210 ab LP4K1201 ab 126. a See Table 18.91: For TeSys K ontators with spring terminal lamps, add a 3 before the oil voltage ode (for example, LC1K06103G7). For TeSys K ontators with solder pin terminals, add a 5 before the oil voltage ode (for example, LC1K09105B7). For TeSys K ontators with slip-on terminals, add a 7 before the oil voltage ode (for example, LC1K12107M7). b Complete the atalog number with the appropriate oil voltage ode (for example, LC1K0610G7). Table 18.91: Coil Voltage Codes for DC Contators Low Consumption a Vd Code JW3 BW3 EW3 SW3 a 1.8 inrush sealed. LR2K0316 E CCN NLDX (srew terminals) LR43364 Class E CCN NLDX2 (slip-on & solder-pin terminals) Table 18.92: Overload Relays for 3-Pole Contators with Srew-Clamp Terminals Class 10, Relay setting range A 0.1 to 0.16 LR2K LR2K overload relays: 0.16 to 0.23 LR2K to 0.36 LR2K to 0.54 LR2K to 0.8 LR2K to 1.2 LR2K to 1.8 LR2K to 2.6 LR2K to 3.7 LR2K to 5.5 LR2K to 8 LR2K to 11.5 LR2K to 14 LR2K Aessories page Dimensions page AC or DC protetion Ambient ompensated bimetalli Class 10 Single phase sensitivity Manual or auto reset Full load urrent dial Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

25 LC2K09107 LP2K0910 Contators 3-Pole Reversing Mini-Contators Table 18.93: AC Operating Coils 115V hp Maximum Horsepower Ratings Maximum Current 1 Ø 3 Ø Indutive 230V 200V 230V 460V 575V AC3 hp hp hp hp hp A Resistive AC1 A TeSys K 3-Pole Reversing Contators Type of Connetion Srew-lamp Srew-lamp Srew-lamp Auxiliary Contats N.O. Refer to 8502CT9901 N.C. 1 LC2K0610 ab LC2K0601 ab LC2K0910 ab LC2K0901 ab LC2K1210 ab LC2K1201 ab 191. Table 18.94: Coil Voltage Codes for AC Contators Up to and inluding 240 V oil with integral suppression devie available. Add 2 to the ode required. Example: J72. Prie adder $ Va 50/60 Hz / / / / / Code J7 B7 D7 E7 F7 G7 FC7 L7 M7 P7 U7 UE7 Q7 N7 R7 T7 Y7 Table 18.95: DC Operating Coils Srew-lamp Srew-lamp Srew-lamp 660/ LP2K0610 ab LP2K0601 ab LP2K0910 ab LP2K0901 ab LP2K1210 ab LP2K1201 ab 232. Table 18.96: Coil Voltage Codes for DC Contators Coil with integral suppression devie available. Add 3 to the ode required. Example: JD3. Prie adder $ Vd Code JD ZD BD CD ED ND SD KD FD GD LD MD MPD MUD UD Table 18.97: DC Low Consumption Operating Coils (devies have built-in transient suppression) Srew-lamp Srew-lamp Srew-lamp Table 18.98: Coil Voltage Codes for DC Contators Low Consumption a b 1 LP5K0610 ab LP5K0601 ab LP5K0910 ab LP5K0901 ab LP5K1210 ab LP5K1201 ab 274. Vd Code JW3 BW3 EW3 SW3 For TeSys K ontators with spring terminal lamps, add a 3 before the oil voltage ode (for example, LP2K09103BD). For TeSys K ontators with solder pin terminals, add a 5 before the oil voltage ode (for example, LP5K09105BW3). For TeSys K ontators with slip-on terminals, add a 7 before the oil voltage ode (for example, LC2K06107B7). Complete the atalog number with the appropriate oil voltage ode (for example, LC1K0610G7). Overload Relays page Aessories page Dimensions page Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

26 Contators LC2K Table 18.99: AC Operating Coils 115 V hp Maximum Horsepower Ratings TeSys K 4-Pole Contators Maximum Current 1 Ø 3 Ø Indutive 230 V 200 V 230 V 460 V 575 V AC3 hp hp hp hp hp (A) Resistive AC1 (A) Refer to 8502CT9901 Type of Connetion Power Poles N.O. N.C. 4-Pole Mini Contator Srew-lamp 4 LC1K09004 ab LC1K09008 ab Srew-lamp 4 LC1K12004 ab Pole Mehanially Interloked Contators Srew-lamp 4 LC2K09004 ab Srew-lamp 4 LC2K12004 ab 191. Table : Coil Voltage Codes for AC Contators Up to and inluding 240 V oil with integral suppression devie available. Add 2 to the ode required. Example: J72. Prie adder $10.00 ($20.00 for mehanially interloked ontators) Va 50/60 Hz / / / / / /690 Code J7 B7 D7 E7 F7 G7 FC7 L7 M7 P7 U7 UE7 Q7 N7 R7 T7 Y7 Table : DC Operating Coils 4-Pole Mini Contator Srew-lamp LP1K09004 ab LP1K09008 ab Srew-lamp 4 LP1K12004 ab Pole Mehanially Interloked Contators Srew-lamp 4 LP2K09004 ab Srew-lamp 4 LP2K12004 ab 232. Table : Coil Voltage Codes for DC Contators Coil with integral suppression devie available. Add 3 to the ode required. Example: JD3. Prie adder $10.00 ($20.00 for mehanially interloked ontators) Vd Code JD ZD BD CD ED ND SD KD FD GD LD MD MPD MUD UD Table : DC Low Consumption Operating Coils (devies have built-in transient suppression) 4-Pole Mini Contator Srew-lamp 4 LP4K09004 ab LP4K09008 ab Srew-lamp 4 LP4K12004 ab Pole Mehanially Interloked Contators Srew-lamp 4 LP5K09004 ab Srew-lamp 4 LP5K12004 ab 274. Table : Coil Voltages for DC Contators Low Consumption a b Vd Code JW3 BW3 EW3 SW3 For TeSys K ontators with spring terminal lamps, add a 3 before the oil voltage ode (for example, LC1K09103L7). For TeSys K ontators with solder pin terminals, add a 5 before the oil voltage ode (for example, LP4K06015JW3). For TeSys K ontators with slip-on terminals, add a 7 before the oil voltage ode (for example, LP2K090047BD). Complete the atalog number with the appropriate oil voltage ode (for example, LC1K0610G7). Overload Relays page Aessories page Dimensions page Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

27 LA1KN11 Contators and Aessories Table : Instantaneous Auxiliary Contat Bloks Clip-on front mounting, 1 blok per ontator and 2 bloks per pair of mehanially interloked ontators. Type of onnetion N.O. Auxiliary Contats TeSys K Contators and Aessories N.C. Refer to 8502CT LA1KN LA1KN LA1KN Srew lamp 4 LA1KN40 a LA1KN31 a LA1KN22 a LA1KN13 a LA1KN04 a LA1KN LA1KN LA1KN Slip-on 1 x in. or 2 x in. 4 LA1KN407 a LA1KN317 a LA1KN227 a LA1KN137a LA1KN047 a a Blok of 4 ontats annot be used with LP4K or LP5K ontators. LA1KN22 LA2KT2U Table : Eletroni Time Delay Auxiliary Contat Bloks Clip-on front mounting, 1 blok per ontator and 2 bloks per pair of mehanially interloked ontators. Voltage (V) Type Timing Range Contats (S) Va or Vd On-delay 1 30 SPDT LA2KT2E Va On-delay 1 30 SPDT LA2KT2U Note: Relay outputs, with single pole double throw, 240 Va/Vd, 2 A max. Maximum swithing apaity 250 VA / 150 W Operating temperature: 10 to + 60 C (14 to 140 F) Reset time: 1.5 s during time delay, 0.5 after time delay Table : Suppressor Module with Inorporated LED Indiator Clip-on front mounting Voltage range Type Sold in lots of eah Va/Vd Varistor 5 LA4KE1B b Va/Vd Varistor 5 LA4KE1E b Va/Vd Varistor 5 LA4KE1FC b Va/Vd Varistor 5 LA4KE1UG b Vd Diode + Zener 5 LA4KC1B Vd Diode + Zener 5 LA4KC1E Va RC 5 LA4KA1U d 9.80 b Protetion by limitation of the transient voltage to 2 U maximum. Maximum redution of the transient voltage peaks. Slight time delay on drop-out ( times normal). No overvoltage or osillation frequeny. Polarized omponent. Slight time delay on drop-out ( times normal). d Protetion by limitation of the transient voltage to 3 U maximum and limitation of the osillation frequeny. Slight time delay on drop-out (1.2 times normal). Table : Paralleling Links Desription Sold in lots of eah For 2 poles with srew-lamp terminals 4 LA9E For 4 poles with srew-lamp terminals 2 LA9E Table : Power Connetors Desription Set of 6 power onnetions for reversing ontators with srew-lamp terminals Set of 4 power onnetions for hangeover ontators with srew-lamp terminals Sold in lots of eah 100 LA9K LA9K Table : Marking Strips Desription Sold in lots of eah Clips onto front of the ontator 100 LA9D90.06 Table : Aessories for Overload Relays Desription Type of Connetion Terminal blok for separate lip-on mounting of the overload relay onto 35 mm omega rail (AM1DP200) Srew-lamp LA7K E CCN NLDX LR43364 Class Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

28 Motor Starters TeSys U Simple Motor Starter Refer to 8502CT The TeSys U motor starter is integrated, making it simple to hoose and install. It onsists of a ontrol unit snapped in a power base. TeSys U an be onfigured to fit speifi appliations as well. Optional aessories inlude a reverser, a urrent limiter, preditive maintenane options, and ommuniation options. For detailed information about TeSys U, visit our website. 1 Power Base 2 Control Unit 3 Funtion Modules Auxiliary Contats + TeSys U Motor Starter Seleting TeSys U Motor Starters in Three Steps Power Base Control Unit Auxiliary Contat E CCN NLDX LR43364 Class Table : Step 1. Selet Power Base (Only two different bases up to 32 A) Control Connetion Max. Current (A) Aessories pages to Dimensions page Three Phase (HP max.) Single Phase (HP max.) Self-Proteted Power Base 200/208 V 220/240 V 460 V 575/600 V 120 V 240 V With srew terminations LUB12 LUB Without srew terminations LUB LUB For use with reversng modules or ommuniation modules with prewired onnetor Table : Step 2. Selet Control Unit g Setting Range (A) e f Standard 3-phase Class 10 trip e Advaned 3-phase Class 10 trip e Advaned single-phase Class 10 trip e Advaned 3-phase Class 20 trip e LUCAX LUCBX LUCCX LUCDX LUCA1X LUCB1X LUCC1X LUCD1X LUCA LUCB LUCC LUCD LUCA LUCB LUCC LUCD LUCA LUCB LUCC LUCD LUCA LUCB LUCC LUCD Complete the atalog number by adding appropriate ode from voltage ode table below (for example, LUCAX6FU). The ontrol unit ontains solid-state overload relay and ontrol power soure for TeSys U. For more details on the different ontrol units, their funtions, and plaement on the power base, see Table : Voltage Codes Volts DC BLg AC B DC or AC ESh FU g DC voltage with range of 0.90 to 1.10 of nominal. h Vd; 48 Va Table : Step 3. Selet Auxiliary Contats (optional) Terminals Contat Indiates Contat Normal Status Off Ready Run Contat State for Eah Modea Short Ciruit Trip Overload Trip (Manual Reset) Overload Trip (Remote/ Auto Reset)b Auxiliary Contat Bloks Ready ondition N.O. O I I O O I Srew LUA1C11 Fault ondition N.C. I I I O O I Ready ondition N.O. O I I O O I LUA1C20 Srew Fault ondition N.O. O O O I I O Auxiliary Contat Funtion Modules Srew Pole state 2 N.O. O O I O O LUFN20 Srew Pole state 1 N.O. and 1 N.C. O I O I I O O I O I LUFN11 Srew Pole state 2 N.C. 1 I O I I LUFN02 a I indiates losed ontat; O indiates open ontat b Requires multifuntion or advaned ontrol unit plus fault differentiation module LUFDA10. Table : Aessories Aessory Quik Desription For details & seletion, see: Current limiter Inreases the breaking apaity to 460 V Table Reverser Staked or side mounted (LU6MB0 only) Table Line phase barrier Required for use as a self-proteted ombination starter (UL508E) Table Multifuntion ontrol unit Has funtions for monitoring and preditive maintenane Table Funtion modules Fault differentiation, thermal overload, motor load indiation Table Communiation modules Integrates into existing networks, major portools are available Table Soft starter + Tesys U Use Altistart U01soft starter with TeSys U Table Powerbus Use TeSys U with a prewired system Table Configuration and onnetion aessories PowerSuite software, busbar, external handle Table Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

29 Control Units Table : Control Units and Funtions TeSys U Simple Motor Starter Refer to 8502CT0201 Standard Advaned Multifuntion Referene LUCA LUCB LUCC LUCD LUCM Protetion type Class 10 Class 20 Class 5 30 Single Phase: LUCC Class 10 only Protetion funtions Short iruit Over urrent Thermal overload Phase loss Phase imbalane Ground fault Underload, long start, jam Control funtions Manual reset Automati or loal/remote reset Fault differentiation Thermal alarm Motor load display Fault history Alarm threshold adjustment Tripping test built-in the ontrol unit works with the related funtion modules (see Table on page 30) Power Base and Plug-in Aessories See below where to install aessories on the power base. Only one aessory an be installed in eah loation. b j b Line Phase Barrier e Reverser Unit mounts under power base j Current Limiter attahes above power base m Multifuntion Control Unit 3 2 Control Unit or mmultifuntion Control Auxiliary Funtion or Communiation Module Control Ciruit Contat Blok 1 Auxiliary Contat Blok e Power Base (Front View) Side View 2012 Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

30 Aessories Line Phase Barrier Reverser Unit Assembled under the Power Base Table : Line Phase Barrier (optional) a TeSys U Simple Motor Starter Refer to 8502CT Desription Inoming line phase barrier to allow the TeSys U to be used as a self proteted ombination starter aording to UL508E LU9SP a See page for plaement on the power base. Table : Reverser Control Connetion With srew terminations b Voltage ode required. Max. Current (A) Table : Selet Control Unit Optionsde Setting Range (A) Standard 3-phase Class 10 trip Three Phase (HP max.) 200/208 V 220/240 V 460 V 575 V Self-Proteted Starter Base LU2B12b LU2B32b Advaned 3-phase Class 10 trip Advaned single-phase Class 10 trip Advaned 3-phase Class 20 trip LUCAX LUCBX LUCCX LUCDX LUCA1X LUCB1X LUCC1X LUCD1X LUCA LUCB LUCC LUCD LUCA LUCB LUCC LUCD LUCA LUCB LUCC LUCD LUCA LUCB LUCC LUCD Complete the atalog number by adding the appropriate ode from Table (for example, LUCAX6FU). d Control units for and 8 32 an be used only with 32 A rated power bases (LUB32 / LU2B32). e The ontrol unit ontains solid-state overload relay and ontrol power soure for TeSys U. For more details on the different ontrol units, their funtions, and plaement on the power base see page Table : Voltage Codes f g h Volts DC BLfg AC B DC or AC ESh FU Voltage ode to use for a power base with a ommuniation module. DC voltage with range of 0.90 to 1.10 of nominal Vd; 48 Va Table : Reversing Modules for Field Addition Mounting No. Wiring Adapter Beneath LU2MB LU9MR1C Note: For LU2MB0 and LU6MB0, voltage ode Beside LU6MB LU9MR required; must math ontrol unit. Table : Current Limiter ij Aessory Appliation Tehnial Data Mounting Current limiter/isolator Additional urrent limiting aspets for 130 ka at 460 V the starter 60 ka at 575 V Diret mounting to LUB and LU2B LUALB Limiter artridge Replaement artridge for LUALB1 130 ka at 460 V 65 ka at 575 V LUALF i Inreases the breaking apaity of the motor starter. j See page for plaement on the power base. Control Unit Multifuntion Table : Control Unit Multifuntion kl Setting Range (A) Multifuntion programmable LUCMX6BL LUCM1XBL LUCM05BL 3 12 LUCM12BL LUCM18BL 8 32 LUCM32BL k Offers motor management system apabilities. For more details see the LUCM on page l See page for plaement on the power base. Alarm Differentiation Parallel Wiring Motor Load Indiator Table : Funtion Modules mn Module Desription For use with: Fault differentiation with manual reset (thermal overload) Fault differentiation with auto reset Thermal overload pre-alarm Provides indiation between an overload trip and a short iruit trip. Advaned ontrol units only Signals when the motor urrent reahes 1.05 of Advaned ontrol units only the full load setting on the ontrol unit. Provides a signal proportional to the average urrents in the three phases divided by the full Advaned or multi-funtion Motor load indiation load urrent setting of the ontrol unit. The ontrol units output orresponds to a load status of 0 2 times the full load setting of the ontrol unit. Provides a onvenient way to redue ontrol Advaned or multi-funtion Parallel wiring wiring and allow for onneting starters to a ontrol units(24 Vd only) ommuniations network by providing 24 Vd and LU9BN11C or LU9MRC for the starters. prewired onnetor m Offers ustomization for speifi appliation requirements. n See page for plaement on the power base. Operation Requirements Va or Vd (power from ontrol unit) Va or Vd (power from ontrol unit) 4 20 ma (requires separate 24 Vd power supply) LU9G02 splitter box and PLC network LUFDH LUFDA LUFW LUFV LUFC Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

31 AS-Interfae Modbus DevieNet Profibus CANopen Aessories Table : Communiation Modules op AS-Interfae Communiation AS-Interfae V2 Communiation Configuration and Connetion Aessories \ Powerbus Module Desription For use with: Modbus Communiation Protool Advantys STB Communiation CANopen Communiation Bekoff Communiation Profibus Communiation DevieNet Communiation o p Allows the TeSys U starter to be onneted diretly to the network using AS-Interfae protools. Allows the TeSys U starter to be onneted diretly to the network using AS-Interfae V2 protools. Allows the TeSys U starter to be onneted diretly to the network using Modbus protools. Allows the TeSys U starter to be onneted to the network using the Advantsys STB protool Allows the TeSys U starter to be onneted to the network using the CANopen protool Allows the TeSys Ustarter to be onneted to the network using the Bekoff protool Allows the TeSys U starter to be onneted to the network using the Profibus protool Allows the TeSys U starter to be onneted to the network using the Devie Net protool TeSys U Simple Motor Starter Operation Requirements Advaned or multi-funtion ontrol units (24 Vd only) Requires separate 24 Vd and LU9BN11C or LU9MRC power supply and AS-Interfae prewired onnetor network Advaned or multi-funtion ontrol units (24 Vd only) and LU9BN11C or LU9MRC prewired onnetor Requires separate 24 Vd power supply and AS-Interfae V2 network Advaned or multi-funtion ontrol units (24 Vd only) Requires separate 24 Vd and LU9BN11C or LU9MRC power supply prewired onnetor Advaned or multi-funtion ontrol units (24 Vd only) and LU9BN11L or LU9MRL prewired onnetor Advaned or multi-funtion ontrol units (24 Vd only) and LU9BN11L or LU9MRL prewired onnetor Advaned or multi-funtion ontrol units (24 Vd only) and LU9BN11L or LU9MRL prewired onnetor Advaned or multi-funtion ontrol units (24 Vd only) and LU9BN11L or LU9MRL prewired onnetor Advaned or multi-funtion ontrol units (24 Vd only) and LU9BN11L or LU9MRL prewired onnetor Requires separate 24 Vd power supply Requires separate 24 Vd power supply Requires separate 24 Vd power supply Requires separate 24 Vd power supply Requires separate 24 Vd power supply Communiation apabilities an be integrated into existing automation arhiteture via a variety of protools. See for plaement on the power base. Table : Control Ciruit Aessories q Aessory Appliation Tehnial Data Mounting Control iruit ontat blok Through-the-door operating mehanism Control iruit filters Swithes ontrol iruit power via LUB handle (NEC ompliane) Use to enlose TeSys LUB only. Use with eletroni or tria output ontrollers 5 A at 600 Va 5 A at 250 Vd NEMA 1, 12 Blak w/ trip indiation NEMA 1, 12 Red/Yellow w/ trip indiation NEMA 3R, 4, 4X Red/Yellow without trip indiation Side mounting to LUB and LU2B only Up to 150 Va max. Diretly to oil terminals Refer to 8502CT0201 ASILUFC ASILUFC LULC LULC LULC LULC LULC LULC LUA8E Kit LU9APN Kit LU9APN Kit LU9APN Non-reversing LUA4F Reversing LUA4F Angle braket Support shaft, for use with LUB GVAPK q See page 29 for plaement on the power base. Table : PowerSuite Configuration Software and Aessories Item a b PowerSuite software VW3A PC onnetion kit VW3A Poket PC onnetion kit VW3A a For omplete details on all omponents inluded with eah item, refer to atalog 8502CT0201. b Items under disount shedule CP4C. Table : GV2 Cabling Aessories Bus Bars 3-Pole, 63 A Bus Bar Desription Appliation Pith Standard Pak Eah For feeding 2 GV2 starters or TeSys U ontrollers For feeding 3 GV2 starters or TeSys U ontrollers For feeding 4 GV2 starters or TeSys U ontrollers For feeding 5 GV2 starters or TeSys U ontrollers 45 1 GV2G GV2G GV2G GV2G GV2G GV2G GV2G GV2G GV2G Additional aessories and omponents are available, inluding: Mounting aessories Gateways Cabling aessories Magelis remote display unit For the omplete line of TeSys U-Line motor starter aessories and all tehnial details (speifiations, wiring diagrams, et.) pertaining to the produt line, refer to 8502CT Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

32 Soft Starters ATSU01 Altistart Drive and TeSys U Simple Motor Starter Altistart Drive and TeSys U Motor Starter Refer to 8502CT Table : Soft Start / Soft Stop Unit for 0.75 to 15 kw Motors (an be ombined with the TeSys U starter) Motor Motor Powera 230 V 460 V Nominal Current HP HP A Starter 3-phase supply voltage: V 50/60 Hz ATSU01N206LT ATSU01N209LT ATSU01N212LT ATSU01N222LT ATSU01N232LT a Standard motor power ratings, HP power ratings indiated aording to standard UL 508. ATSU01 Table : Aessories Desription Used for Starter Power onnetor between ATSU 01N2 LT and TeSys U ATSU01N2 T VW3G Table : TeSys U Starter and Soft Start Unit Combinations b Motor Power Voltage 200 V 460 V Soft Starter Power Base TeSys U Control Unit b HP HP 1 2 ATSU01N206LT LUC 05BL ATSU01N206LT LUC 12BL 2 5 ATSU01N209LT 3 ATSU01N212LT LUB 12 LUC 12BL LUC 12BL 7.5 ATSU01N212LT LUC 18BL 5 10 ATSU01N222LT LUC 18BL ATSU01N222LT LUC 32BL LUB ATSU01N232LT LUC 32BL Depending on the onfiguration of the hosen TeSys U starter, replae the with A for standard, B for advaned, and M for multifuntion. See page for a omplete list of available ontrol units. Control voltage must be 24 Vd. E CCN NLDX LR96921 Class Shneider Eletri CP1G I11 Disount This doument provided by Barr-Thorp Eletri Co., In

33 GV2ME GV2P21 with GV2GH7 installed GV3P GV7RE20 E CCN NLRV LR81630 Class Starters TeSys GV2, GV3, and GV7 Manual Starter and Protetor Refer to 2520CT0001 The GV family of produts are 3-pole, horsepower rated, UL 508 listed manual starters. They inlude a manual disonnet, lass 10 ambient-ompensated thermal overload relay, and instantaneous, magneti trip mehanism in one ompat unit. Any GV manual starter an be used alone for loal manual ontrol of a motor with individual full-load urrents up to 220 A. The GV produts may also be used in group motor installations in aordane with National Eletri Code artile Group motor installations give you greater panel density for smaller size and require fewer parts and less wiring for installation when ompared to onventional panel designs. The GV2P and GV3P produts also have an additional UL 508 type E rating as a stand-alone, self-proteted manual ombination starter. The UL 508 type E rating requires the addition of line side insulating barrier GV2GH7 for the GV2P, or GV3G66 for the GV3P. The GV2P and GV3P self-proteted manual ombination starters may also be ombined with speifi size ontators from the LC1D produt family for a UL 508 Type F ombination starter onstrution. These produts have a UL-listed short iruit urrent rating from ka depending on appliation size and voltage. See the Shneider Eletri website for more information. How to Order To order a basi motor starter, selet the model number (GV2ME, GV2P, or GV3P ) with the appropriate thermal setting from the table below. The thermal trip range and setting should be determined from the motor nameplate full-load urrent. Table : GV2, GV3 Thermal Setting (A) 115 V hp Maximum Horsepower Ratings 1 Ø 3 Ø 230 V hp 200 V hp 230 V hp 460 V hp 575 V hp Group Motor Appliations Max. Fuse or Ciruit Breaker GV2/3M push button GV2/3P rotary handle Motor Protetor Ciruit Breakers Motor protetor iruit breakers provide built-in thermal and magneti protetion. They are used in two-devie motor feeder solutions to provide protetion against short iruits, overloads, and phase imbalane A GV2ME01a 159. GV2P A GV2ME02a 159. GV2P A GV2ME03a 159. GV2P A GV2ME04a 180. GV2P A GV2ME05a 180. GV2P A GV2ME06a 180. GV2P A GV2ME07a 180. GV2P / A GV2ME08a 180. GV2P / A GV2ME10a 180. GV2P A GV2ME14a 180. GV2P A GV2ME16a 224. GV2P A GV2ME20a 224. GV2P A GV2ME21a 224. GV2P A GV2ME22a 224. GV2P A GV2ME GV2P GV3P GV3P GV3P GV3P GV3P GV3P GV3P a For spring terminals add 3 to the atalog number (for example, GV2ME013). GV2ME32 is not available with spring terminals. For ring terminals, add 6. Table : GV7 Thermal Setting (A) 115 V hp Maximum Horsepower Ratings Toggle Operator 1 Ø 3 Ø Standard Interrupt High Interrupt 230 V hp 200 V hp 230 V hp 460 V hp 575 V hp GV7RE GV7RS GV7RE GV7RS GV7RE GV7RS GV7RE GV7RS GV7RE GV7RS GV7RE GV7RS GV7RE GV7RS GV7RE GV7RS Speifiations: page Aessories: pages to Dimensions: pages to Table : Two-Devie Solutions Eletroni Motor Protetor Ciruit Breakers with UL Ratings: H-Frame (150A), J-Frame (250 A), and L-Frame (600 A)b (refer to disount shedule DE2) Eletroni Trip Unit Type Frame Sensor Rating Trip Unit Full Load Ampere Rating (FLA) Isd (x FLA) G Interrupting J Interrupting L Interrupting Cat. No. Cat. No. Cat. No x FLA HGL36030M38X HJL36030M38X HLL36030M38X x FLA HGL36050M38X HJL36050M38X HLL36050M38X H-Frame M x FLA HGL36100M38X HJL36100M38X HLL36100M38X Standard x FLA HGL36150M38X HJL36150M38X HLL36150M38X J-Frame x FLA JGL36250M38X JJL36250M38X JLL36250M38X x FLA LGL36400M38X LJL36400M38X LLL36400M38X L-Frame 2.3 M x FLA LGL36600M38X LJL36600M38X LLL36600M38X b Two-devie solutions (these eletroni motor protetor iruit breakers inlude short iruit and overload protetion): 1 ontator, plus 1 eletroni motor iruit protetor with a Mirologi 2.2 M The standard trip unit offers Class 5, 10, and 20 and phase unbalane or phase loss protetion Shneider Eletri. I11 Disount This doument provided by Barr-Thorp Eletri Co., In

34 Starter Aessories GVAU116 GVAE11 Table : Voltage Trips TeSys GV2 and GV3 Manual Starters and Protetors Refer to 2502CT Only one trip or fault signaling ontat an be installed per GV2/GV3 devie. Desription Charateristis Voltage Frequeny a Voltage trips GV2 & GV3P a Undervoltage or Shunt trip (external mounting, 1 blok right side only) To order an undervoltage trip: replae the bullet ( ) with a U (for example, GVAU025). To order a shunt trip: replae the bullet ( ) with an S (for example, GVAS025). Table : Auxiliary Contat Bloks Desription Instantaneous auxiliary ontats GV2 + GV3P Fault signaling ontat + instantaneous auxiliary ontat GV2 + GV3P Mounting Loation 24 V 50 Hz 60 Hz GVA 025 GVA V 60 Hz GVA Hz GVA V 50/60 Hz GVA V 50 Hz GVA Hz GVA V 50 Hz GVA V 60 Hz GVA V 50 Hz GVA V 60 Hz GVA V 50 Hz 60 Hz GVA 225 GVA V 50 Hz GVA Hz GVA V 50 Hz GVA V 60 Hz GVA V 60 Hz GVA V 60 Hz GVA V 50 Hz 600 V 60 Hz GVA 505 Max. No. of Bloks Frontbg 1 Left Hand Side 2 Left Hand Sided Contat Type Sold in lots of N.O. or N.C. 1 GVAE N.O. + N.C. 10 GVAE11e N.O. + N.O. 1 GVAE20e N.O. + N.C. 1 GVAN11e N.O. + N.O. 1 GVAN20e N.O. (fault) + N.O. 1 GVAD N.O. (fault) + N.C. 1 GVAD N.C. (fault) + N.O. 1 GVAD N.C. (fault) + N.C. 1 GVAD Short iruit signaling ontat GV2 + GV3P Left Hand Side 1 SPDT 1 GVAM b Mounting of a GVAE ontat blok or a GV2AK00 visible isolation blok on GV2P. Choie of N.C. or N.O. ontat operation, depending on whih way the reversible blok is mounted. d The GVAD is always mounted next to the starter. e For spring terminals, add 3 to the atalog number (for example, GVAE113). f One trip or one fault signaling an be fitted per GV3. g Cannot be used with GV2GH7 insulator. GVAD0101 Table : Voltage Trips Tehnial Data (GV2AU, GV2AS) Rated Voltage 660 Va Model Inrush Sealed Pik-Up Voltage Drop-Out Voltage Operating Timeh GVAU 12 VA / 8 W 3.5 VA / 1.1 W ms GVAS 14 VA / 10.5 W 5 VA / 1.6 W ms h From the loss of voltage at the trip terminals to the opening of the starter ontats. Table : GV3P Aessories Aessory Appliation / Use With NEMA 1, 12, Blak with trip indiation, for use with GV3P GV3APN Through-the-door operating mehanism (Qty: 1) NEMA 1, 12, Red/Yellow, with trip indiation, for use with GV3P GV3APN NEMA 3R, 4, 4X Red/Yellow without trip indiation, for use with GV3P GV3APN Angle braket (Qty: 1) Support shaft, for use with GV2P and GV3P GVAPK Hard braket (Qty: 1) GVAPH Set of 3-pole 115 A busbars (tap-offs: 2, pith: 64 mm) GV3P GV3G Set of 3-pole 115 A busbars (tap-offs: 3, pith: 64 mm) GV3P GV3G Cover Larger Spaing UL 508 type E (Only one over required on supply side) GV3P GV3G IP 20 over (Two overs required per starter) GV3P LAD Padloking devie For use with up to 4 padloks (not supplied) GV3P Ø 6 mm shank maximum GV3P GV2V GVAN Shneider Eletri CP10 I11 Disount This doument provided by Barr-Thorp Eletri Co., In

35 Starter Aessories TeSys GV2, GV3, GV7 Manual Starters and Protetors Refer to 2502CT0001 Table : Auxiliary Contat Bloks (auxiliary ontat funtions depends on loation inside the devie) Desription Mounting Loation Max. No. of Bloks Contat Type Standard GV7AC01 Instantaneous 2 per devie N.O. + N.C. Trip Indiation Inside Devie 1 per devie N.O. + N.C. Fault Indiation 1 per devie N.O. + N.C. Low Level Instantaneous 2 per devie N.O. + N.C. Trip Indiation Inside Devie 1 per devie N.O. + N.C. Fault Indiation 1 per devie N.O. + N.C. Table : Voltage Trips GV7AE GV7AB Desription Mounting Loation Max. No. of Bloks Voltage GV7RE20 GV7AD111 GV7AS Va 50 Hz GV7AU Va 50/60 Hz GV7AU107 Undervoltage Trip Inside Devie 1 per devie Va 50/60 Hz GV7AU /480 Va 50/60 Hz GV7AU Va 50 Hz GV7AU Va 50 Hz GV7AS Va 50/60 Hz GV7AS107 Shunt Trip Inside Devie 1 per devie Va 50/60 Hz GV7AS /480 Va 50/60 Hz GV7AS Va 50 Hz GV7AS525 Fault Indiation Inside Devie 1 per devie GV7AD GV7AD Table : Wiring Aessories Desription Appliation Box Lugs Sold in lots of 3 for GV7R i GV7AC eah Sold in lots of 3 for GV7R 220i GV7AC eah Phase Barriers, Bus Bars & Shrouds Terminal Extension Kit Inreases enter distane between phases to 45 mm GV7AC Terminal Shroud Kit Covers terminal onnetions for touh safe protetion GV7AC Phase Barriers Provides maximum phase separation at onnetion points GV7AC Insulating Barriers Provides insulation between onnetors and bakplate GV7AC Busbars and Covers Connet to LC1F ontator GV7AC Connet to LC1F ontator GV7AC Operating Handles and Aessories Blak rotary operating handle with blak legend plate (mounts diretly on devie) GV7AP Red rotary operating handle with yellow legend plate (mounts diretly on devie) GV7AP Conversion aessory to mount the devie diretly on panel door GV7AP Blak rotary operating handle with blak legend plate and extension kit ( mm) GV7AP Red rotary operating handle with yellow legend plate and extension kit ( mm) GV7AP Padloking devie for toggle handle (max. 38 mm padloks) GV7V i Wire size: GV7AC to 3/0 AWG; GV7AC AWG to 350 kmil. GV7AP03 Table : Operating Handles For use with GV2, GV3, and TeSys U through-the-door operating mehanisms Aessory Desription Operating Handle (Qty: 1) NEMA 1, 12, Blak with trip indiation GVAPB NEMA 1, 12, Red/Yellow, with trip indiation GVAPR NEMA 3R, 4, 4X Red/Yellow without trip indiation GVAPR Dimensions pages to GVAPB54 GVAPR54 GV7AC021 GV7V01 GV7AE Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

36 Starter Aessories TeSys Manual Starters and Protetors LS1 Fuseholders 45 mm wide (same dimensions as GV2ME) Available with srew lamp and spring type terminals Mounts diretly to LC1D09 D32 ontators (with use of GV2AF3 or GV2AF4) Meets appliation needs for fusible starter Uses GV2AE instantaneous ontat bloks to open ontrol iruits DIN rail mounted Table : LS1 Fuseholders Refer to 2502CT Dimensions Desription Fuse Type in. mm Use In Spring terminals, 3-pole CC, KTK-R 0.41 x x 38 US Markets LS1D Srew lamp terminals, 3-pole CC, KTK-R 0.41 x x 38 US Markets LS1D Spring terminals, 3-pole am, gg 0.39 x x 38 European Markets LS1D Srew lamp terminals, 3-pole am, gg 0.39 x x 38 European Markets LS1D Auxiliary main pole adder am, gg 0.39 x x 38 European Markets LA8D324a 65. a Can be mounted on left-hand or right-hand side of the 3-pole LS1D32 blok. LS1D30 Table : Speifiations Type LS1D30, LS1D303 LS1D32, LS1D323, LS1DT32 Max. voltage 600 V 3 Phase Max. urrent 30 A Conforming to standards IEC , , , EN60204, BS4841, UL 508, CSA No. 14, NFC , , , VDE 0113, 0660 Produt approvals UL, CSA BV Protetive treatment TH TH Ambient air temperature operation -58 to 158 o F (-50 to +70 o C) Wiring of ondutors and ross setional area (.s.a.) Solid able 2 x 16 8 AWG (1 6 mm 2 ) Flexible able without able end 2 x 14 8 AWG (1 6 mm 2 ) Flexible able with able end 2 x AWG (1 4 mm 2 ) Resistane to mehanial impat onforming to IEC J Tightening torque 15 in-lb (1.7 N m) Sensitivity to phase failure No Operating Positions Rated voltage 600 V Rated thermal urrent Mehanial life (varies by appliation) 600 V 25 A (GV2), 63 A (GV3) GV2: 100,000 operations Table : Environmental Speifiations and Approvals Shok resistane 30 g (onforming to IEC ) Vibration resistane 5 g (5 to 150 Hz) (IEC ) 40 to 176 F ( 40 to +80 C) for storage Ambient temperature 4 to 140 F ( 20 to +60 C) open operation 4 to 104 F ( 20 to +40 C) enlosed operation Maximum operating rate 25 operations per hour Operating urrent of magneti trip Approximately 13 times the maximum thermal trip (non-adjustable setting) File E CNN NLRV File LR81630 Class Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

37 GV2GH7 LAD31 LAD311 GV2AF3 / GV2AF4 Starter Aessories Table : GV2 Mounting Aessories TeSys GV2 Manual Starters and Protetors Refer to 2502CT0001 Desription Appliation Standard Pak b Common mounting plate For GV2 plus any 3-pole LC1D09 thru LC1D25 ontator. (supplied with GV1G02 onnetor) 1 GK2AF Adapter plate For srew mounting of GV2M 10 GV2AF Interonnet for GV2 plus any 3-pole LC1K or LP1K ontator 10 GV2AF Combination blok Interonnet GV2 and LC1D09 thru D32 10 GV2AF Interonnet GV2 and LC1D09 thru D32 mounted on LAD31 10 GV2AF mm ompensation plate To allow mounting of GV2M and GV2P on a ommon bus bar 10 GV1F Mounting plate For mounting GV2ME or GV2P and ontator LC1D09 thru D32 10 LAD LAD Table : GV2 Cabling Aessories Bus Bars Desription Appliation Pith Standard Pak b 3-Pole, 63 A Bus Bar 45 1 GV2G For feeding 2 GV2 starters 54 1 GV2G GV2G For feeding 3 GV2 starters 45 1 GV2G GV2G GV2G For feeding 4 GV2 starters 54 1 GV2G GV2G For feeding 5 GV2 starters 54 1 GV2G Table : GV2 Other Cabling Aessories Desription Appliation Standard Pak b Top feed for use with bus bars 1 GV1G Terminal bloks Bottom feed, to be used with bus bars; an be fitted with GV1L3 urrent limiter 1 GV2G Protetive end over To over unused bus bar outlets 5 GV1G pole flexible onnetor For onneting a GV2 to an LC1D09 thru D25 ontator 10 GV1G Conduit adapter (1/2" NPT) 1 GV2AK Inoming line insulator For GV2P when used in UL 508 Type E appliationsa 10 GV2GH a Cannot be used with front-mounted auxiliary ontat blok. Table : GV2 Other Aessories Desription Appliation Standard Pak b Visible isolation blok GV2P Front mounting, 3-pole visible isolation on inoming side of GV2P 1 GV2AK Current limiter GV2M Inreases interrupt apaity when attahed to GV2M 1 GV1L NEMA 1, 12, Blak with trip indiation, for use with GV2P 1 GV2APN Through-the-door operating NEMA 1, 12, Red/Yellow with trip indiation, for use with GV2P 1 GV2APN mehanism NEMA 3R, 4, 4X, Red/Yellow without trip indiation, for use with GV2P 1 GV2APN Angle braket Support shaft, for use with GV2P 1 GVAPK Hard braket 1 GVAPH Table : GV2 Enlosures Desription Mounting Rating Enlosures for GV2M with or without aessories (maximum of 1 aessory on right and left) Enlosures are not UL or CSA listed. Surfae mounting Flush mounting Flush mounting redued width (max. of 1 aessory on right) Table : GV2 Enlosures Aessories NEMA 1, IP41 IP55 NEMA 1, IP41 IP55 NEMA 1, IP41 IP55 GV2MC01 GV2MC02 GV2MP01 GV2MP02 GV2MP03 GV2MP Desription Type Standard Pakb Padloking devie for GV2M (when padloked, starter is automatially in Off position) 1 GV2V Spring return 1 GV2K Mushroom head stop push Key release (Ronis key no. 455) 1 GV2K button Lathing (40 mm, red) Turn to Release 1 GV2K Lathing / Padlokable Turn to Release 1 GV2K Sealing kit For enlosures GV2MC01 and GV2MP01 10 GV2E V Green 10 GV2SN V Red 10 GV2SN V Orange 10 GV2SN V White 10 GV2SN17 220/240 V Green 10 GV2SN23 Pilot Light (neon) 220/240 V Red 10 GV2SN24 220/240 V Orange 10 GV2SN /240 V White 10 GV2SN27 380/440 V Green 10 GV2SN33 380/440 V Red 10 GV2SN34 380/440 V Orange 10 GV2SN35 380/440 V White 10 GV2SN37 b Orders must speify multiples of quantities listed. Supplied with IP55 sealing kit Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

38 Wiring, Communiations, and Busbar System APP2R4H1 LAD35 LAD3B LAD33 TeSys Contators and Motor Protetors with Spring Terminals Refer to 8502CT Table : Splitter Boxes A total of up to eight starters is permissible after extensions. Use multiple quantities of the same atalog number to reate the desired line-up. Desription Type of Control-Command Connetion on Control System Side No. of I/O per Starter No. of Starters per Unit 50 A power splitter box 2 LAD LAD x HE10 8I/8O 1I/1O 4 APP2R4H x HE10 16I and 1 x HE10 8O 2I/1O 4 APP2R4H A power and ontrol splitter box via module APP1C a 2 APP2R2E APP2R4E AS-Interfae 2I/1O 2 APP2R2AS I/1O 4 APP2R4AS a Connetion to an APP1C module via APP2CX adapter (LAD35). Table : Power Connetion Components for One Starter Desription Kit Consists Of: Assembly and power onnetion kit One LAD31 plate for GV2ME and two LAD34 power onnetion modules LAD Reversing kit b One set of bus bars and one mehanial interlok LAD b To reate a TeSys D reverser, use two LC1D ontators, one assembly and power onnetion kit, and one reversing kit. Table : Power Connetion Aessories for One Starter Desription Max. Connetion Cross-Setion Use Upstream terminal blok (50 A max) 16 mm 2 (6 AWG) Power supply for one or two power splitter boxes LAD3B Downstream terminal blok (50 A max) 6 mm 2 (10 AWG) Connetion of motor ables LAD Table : Control Connetion Module for One Starter Desription Control onnetion module (integrating ontat blok GVAE20) d D-Line Coil Voltage Va or Vd Type of Coil Control Relay Eletromehanial Vd Without relay d Relay supplied mounted on the front panel of the ontrol onnetion. The use of TeSys D low onsumption ontators is reommended. Table : Spare or Replaement Parts Desription Type of Control-Command Connetion on Control System Side No. of I/O per Starter Type of Starter Non-reversing APP2D Reversing APP2D Non-reversing APP2D1D Reversing APP2D2D No. of Starters Sold in Lots of Plate for mounting a GV2ME manual starter 1 10 LAD LAD Power onnetion module 1 10 LAD x HE10 8I/8O 1I/1O 4 1 APP2R4H x HE10 16I and 1 x HE10 8O 2I/1O 4 1 APP2R4H Control-ommand splitter box (single, for 2 1 APP2R2C Per module APP1C e mounting on a power splitter box) 4 1 APP2R4C AS-Interfae 2I/1O 2 1 APP2R2A I/1O 4 1 APP2R4A Replaement eletromehanial relay (for ontrol onnetion module) 1 10 APP2ER 7.50 e Connetion to an APP1C module via APP2CX adapter (LAD35). APP2D Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

39 Busbar Aessories TeSys AK5 Panel Busbar System Refer to 8502CT0101 The AK5 pre-fabriated bus bar system provides a quik and easy method of mounting ontrol devies. All omponents are finger safe, UL Listed, CSA approved and CE marked. Although the AK5 system an be srew mounted onto any type of support, it must be mounted on the AM1DL201 DIN rail when omponent mounting plates inorporating a tapoff are used. When using tap-offs, the nominal operating urrent of the bus bar ( ) must not be exeeded. Table : 160 A, 3-Phase Busbar System AK5JB143 Maximum number of mounting plates Length Tap-off Standard Width Plate Extension Plate 1.42 in. 36 mm 2.13 in. 54 mm 2.80 in. 71 mm in. mm AK5JB AK5JB AK5JB AK5JB AK5JB AK5JB Table : Mounting Plate Tap-off (plugs into busbar mounted on AM1DL201 DIN rail) AK5PA231 AK5PA232S AK5PC33 AM1DL201 Width Thermal in. mm Current Amperes Appliation A LUS or LUB 12 and 32 AK5PA A GV2 with ontator AK5PA A reversing ontator AK5PA232S Table : Bus Tap-off (plugs into busbar for wiring to a separately mounted devie) Width Thermal Length of Leads Current Amperes in. mm in. mm A AK5 PC A AK5 PC33L Table : Extension Plates Used to mount wider omponents. Bolt to standard mounting plates (after DIN rails are removed). Width Appliation in. mm GV & Reversing ontator AK5PE Table : Mounting Rail (must be used for mounting plates with tap-offs) Depth Length Desription mm mm 75 mm Omega Rail AM1DL Table : Approvals: IEC 439, UL, CSA, DNV, LROS File E CCN NMTR File LR Class Shneider Eletri I11 Disount This doument provided by Barr-Thorp Eletri Co., In

40 Dimensions Table : TeSys D Contators AC Control Ciruits LC1D09 to D18 (3-pole) and LC1DT12 to LC1DT40 (4 pole) TeSys D Contators, AC Coil LC1D25 to D38 (3-pole) Refer to 8502CT Minimum eletrial learane Minimum eletrial learane Minimum eletrial learane Minimum eletrial learane LA4 b1 b b b b AC Coil DC Coil (LAD8) b AC oil, without add-on aessories 3.03 (77) 3.89 (99) 3.14 (80) 3.36 (85) 3.89 (99) 3.34 (85) 3.89 (99) 3.58 (91) 4.13 (105) DC oil AC oil, with LAD4BB b 3.70 (94) 4.21 (107) 3.75 (95.5) 3.85 (98) 4.21 (107) 3.85 (98) b1 AC oil, with LA4D*2 b 4.33 (110) a 4.84 (123) a 4.30 (111.5) a 4.48 (114) a 4.84 (123) a 4.48 (114) AC oil, with LA4DF, DT b 4.68 (119) a 5.19 (132) a 4.76 (120.5) a 4.84 (123) a 5.19 (132) a 5.02 (129) AC oil, with LA4DR, DW, DL b 4.96 (126) a 5.67 (139) a 5.0 (127.5) a 5.11 (130) a 5.47 (139) a 7.48 (190) AC oil, without over or add-on bloks 3.30 (84) 3.30 (84) 3.30 (84) 3.54 (90) 3.54 (90) 3.54 (90) 3.54 (90) 3.85 (98) 3.85 (98) AC oil, with over, without add-on bloks 3.38 (86) 3.38 (86) 3.38 (86) 3.62 (92) 3.62 (92) 3.62 (92) 3.62 (92) 3.93 (100) 3.93 (100) DC oil, without over or add-on bloks 3.66 (93) 3.66 (93) 3.66 (93) 3.89 (99) 3.89 (99) DC oil, with over, without add-on bloks 3.76 (95) 3.76 (95) 3.76 (95) 3.97 (101) 3.97 (101) 3.90 (99) 3.90 (99) 4.21 (107) 4.21 (107) 1 AC oil, with LADN or C (two or four ontats) 4.60 (117) 4.60 (117) 4.60 (117) 4.84 (123) 4.84 (123) 4.84 (123) 4.84 (123) 5.15 (131) 5.15 (131) DC oil, with LADN or C (two or four ontats) 4.96 (126) 4.96 (126) 4.96 (126) 5.19 (132) 5.19 (132) 4.84 (123) 4.84 (123) 5.15 (131) 5.15 (131) 2 AC oil, with LAD6K (129) 5.07 (129) 5.07 (129) 5.31 (135) 5.31 (135) 5.31 (135) 5.31 (135) 5.62 (143) 5.62 (143) DC oil, with LAD6K (138) 5.43 (138) 5.43 (138) 5.66 (144) 5.66 (144) 5.31 (135) 5.31 (135) 5.62 (143) 5.62 (143) AC oil, with LADT,R,S 5.39 (137) 5.39 (137) 5.39 (137) 5.62 (143) 5.62 (143) 5.62 (143) 5.62 (143) 5.94 (151) 5.94 (151) 3 AC oil, with LADT,R,S and sealing over 5.55 (141) 5.55 (141) 5.55 (141) 5.78 (147) 5.78 (147) 5.78 (147) 5.78 (147) 6.10 (155) 6.10 (155) DC oil with LADT,R,S 5.76 (146) 5.76 (146) 5.76 (146) 5.98 (152) 5.98 (152) 5.62 (143) 5.62 (143) 5.94 (151) 5.94 (151) DC oil with LADT,R,S and sealing over 5.90 (150) 5.76 (146) 5.76 (146) 6.14 (156) 6.14 (156) 5.78 (147) 5.78 (147) 6.10 (155) 6.10 (155) a Inluding LAD4BB b Not appliable to devies with DC oils Table : AC Coil LC1D40, D50, D65 (3P), LC1D65004 (4P) LC1D80004 (4P) (LA4 DA2, DE2) (LA4 DF, DT) (LA4 DM, DR, DW, DZ) (LA4 DA2, DE2) (LA4 DF, DT) (LA4 DM, DR, DW, DZ) * (LA1) ** (LA2, LA3, LA6 DK1) 165 *exept LA1DN10, DN ** +4 mm with lead sealing devie (LA8) 2.95(3P) 3.34(4P) (LA8) 6.77** * (LA1) 153 (LA2, LA3, LA6 DK2) *exept LA1DN10, DN ** +4 mm with lead sealing devie (LA8) 3.34(3P) 3.78(4P) (LA8) LC1 D40A D65A (3P), LC1 DT60A DT80A (4P) AC OR DC Minimum eletrial learane b a (LAD 8N) (LAD 8N) LC1 D40A D65A DT60A DT80A D40008 in. (mm) in. (mm) in. (mm) a 2.17 (55) 2.76 (70) 3.35 (85) with LA4 D (135) with LA4 DB3 or LAD 4BB (136) b1 with LA4 DF, DT 6.18 (157) 5.59 (142) with LA4 DM, DW, DL 6.54 (166) 5.91 (150) without over or add-on bloks 4.65 (118) 4.65 (118) 4.92 (125) with over, without add-on bloks 4.72 (120) 4.72 (120) with LAD N (1 ontat) 5.47 (139) 1 with LAD N or C (2 or 4 ontats) 5.91 (150) 5.91 (150) 5.79 (147) 2 with LAD 6K10 or LA6 DK 6.42 (163) 6.42 (163) 6.26 (159) with LAD T, R, S 6.73 (171) 6.73 (171) 6.57 (167) 3 with LAD T, R, S and sealing over 6.89 (175) 6.89 (175) 6.73 (171) Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

41 Table : DC Coil Dimensions LC1D40, D50, D65 (3P), LC1D650004, (4P) LC1D80 (3P), LC1D800004(4P) TeSys D Contators, DC Coil Refer to 8502CT Minimum eletrial learane * (LA1) d (LA6 DK2, LA2, LA3) (3P) 3.34(4P) (LA4 DC3) (LA4 DF, DT) (LA4 DM, DR, DW, DZ) Minimum eletrial learane * (LA1) d (LA6 DK3, LA2, LA3) (3P) 3.78(4P) (LA4 DC3) (LA4 DF, DT) (LA4 DM, DR, DW, DZ) 154 *exept LA1DN10, DN d + 4 mm with lead sealing devie *exept LA1DN10, DN d + 4 mm with lead sealing devie LC1D115, D150 LC1 D115 D1156 D150 D1506 LC1D115, D (LA2, LA3) LA8 G LA (LA4D 2, D 3) (DF, DT) (DM, DR, DW, DL) (132) 4.53 (115) 5.12 (132) 4.53 (115) G (3-poles) 3.78/4.33 (96/110) 3.78/4.33 (96/110) 3.78/4.33 (96/110) 3.78/4.33 (96/110) G (4-poles) 5.12/5.67 (130/144) 5.12/5.67 (130/144) LC1 C A D115, D (132) 4.72 (120) D (132) 6.10 (155) D1156, D (115) 4.72 (120) D (115) 6.10 (155) 5.91q (LA1) (LA6-DK20) 155 a b a With 2 or 4 ontats. + 4 mm with sealing over. LR2D4 bimetalli overload relay Diret mounting beneath ontators LC1D115 and D150 LR9D solid-state overload relay Diret mounting beneath ontators LC1D115 and D d mm DIN rail dimensions 35 mm DIN rail dimensions AM1DP200 and DR200 AM1DE and ED AM1DP200 and DR200 AM1DE and ED d 0.10 (2.5).41 (10.5) d 0.10 (2.5).41 (10.5) Note: All dimensions are in Inhes (mm) d Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

42 Dimensions TeSys F Contators LC1F115 to F330 Refer to 8502CT9901 All dimensions shown in mm. To onvert to inhes, divide by (see Table ) a X1 X1 a L b Protetive over Type LA9F70. b2 Z S s1 Q P P Q1 a G1 G Y M f J J1 b1 Table : LC1F115 F330 Dimensions LC1 3- Pole F115 F150 F185 F265 F Pole 3- Pole 4- Pole 3- Pole 4- Pole 3- Pole 4- Pole 3- Pole 4- Pole a b b b b 165b 165b 165b f G G J J L M P Q Q S S Y Z b +6 mm with time delay blok (for F115 and F150). Optimal terminal shroud f minimum distane required for oil removal. Table : LC1F115 F330 Voltage 220/380 V 415/440 V 500 V 660 V 1000 V LC1F115, F LC1F LC1F LC1F X1: Minimum learane aording to the operational voltage and the breaking apaity. Table : LC1F400 F500 Dimensions LC1F400 to F500 (see Table ) X1 X L b b2 e S Q P P Q1 a M10 X 30 dia. M f 8 X 8.5 dia. LC1 F400 F500 2-Pole 3-Pole 4-Pole 2-Pole 3-Pole 4-Pole a b b f Gd G min G max G1d G1 min G1 max J L M P Q Q S d Supplied e Protetive over f Minimum distane required for oil removal. Table : LC1F400 F500 Voltage /230 V 415/440 V 500 V 660 V 1000 V LC1F LC1F X1: Minimum learane aording to the operational voltage and the breaking apaity G G1 J Dual Dimensions: INCHES Millimeters Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

43 Dimensions TeSys F Contators Refer to 8502CT9901 Table : LC1F Dimensions LC1F630 and LC1F x M12 x 45 Dual Dimensions: INCHES Millimeters 4 x Dia mm X X Q a Q1 7.13* G J1 * minimum distane required for oil removal. Protetive terminal over. LC1F780, F7804 X1 X1 LC1F630 a G supplied G min. G max. J1 Q Q1 in. mm in. mm in. mm in. mm in. mm in. mm in. mm 2 P P P x M14 x X1:Minimum learane aording to the operational voltage and the breaking apaity. Voltage (V) / X1 in mm * f a * 183 X1: Minimum learane aording to the operational voltage and the breaking apaity. Voltage (V) / X1 in mm f Overall length (3 poles) a Overall length (4 poles) *minimum distane required for oil removal. LC1F780 mounting LC1F7804 mounting x Dia mm 8 x Dia mm Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

44 Dimensions Table : Reversing Contator Dimensions LC2D09 D32 LC2DT20 DT60 2 x LC1DT20 DT60 TeSys D Reversing Contators 2 x LP1D40, D65, D80, D95 Refer to 8502CT xØ0.26 6xØ6.5 b 2xM0.16 2xM b e1 G a b G a b e1 e2 G G1 LC2 or 2 x LC1 LC2 or 2 x LC1 in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) DT20 and DT (90) 3.34 (85) 3.54 (90) 3.14 (80) D40 to D (182) 5.0 (127) 7.4 (190) 1.19 (5) 0.43 (11) 2.2 (57) 3.8 (97) DT32 to DT (90) 3.58 (91) 3.85 (98) 3.14 (80) D80 and D (207) 5.0 (127) 8.4 (215) 0.51 (13) 0.78 (20) 3.7 (96) 4.3 (111), e2: inludes abling., e1 and e2: inludes abling. LC2D115 and D150 2 x LC1D115 and D150 Panel mounted with 1/4 in. srew e2 e1 G a Dimensions shown in millimeters (mm 25.4 inhes) e G a e2 G a LC2 or 2 x LC1 (3-pole) a e1 e2 G D115, D /256 LC2 or 2 x LC1 (4-pole) a e1 e2 G D /324, e1 and e2 inludes abling NOTE: For dimensions of TeSys F reversing ontators, please refer to atalog 8502CT Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

45 Dimensions Table : TeSys D Overload Relay Dimensions TeSys D Overload Relays Refer to 8502CT9901 LRD Independent mounting on 50 mm enters or on rail AM1DP200 or DE200 Independent mounting on 110 mm enters LAD7B LAD7B Remote tripping or eletrial reset LAD703 a DX1AP25 LRD, LR2D and LR9D Reset by flexible able LA7D305 and LAD7305 Mounting with able straight 2xØ0.26 2xØ6.5 Mounting with able bent a Can only be mounted on RH side of relay LRD-01 to 35 : up to 21.6 in. (550 mm) e: up to 0.79 in. (20 mm) LRD3tt Beneath LC1DttA ontator Separate mounting LC1Dpp A e e M10x0.04 M10x LR2D1, LR3D1 Separate mounting at 50 mm (1.97 in.) enters or on AM1DP200 or DE200 rail LR2D2, LR3D2 Separate mounting at 50 mm (1.97 in.) enters or on AM1DP200 or DE200 rail LA7-D LA7-D / / / / d 2xØ0.18 2xØ4.5 LR2D1, LR3D1 Separate mounting at 110 mm (4.33 in.) enters d 2xØ0.18 2xØ4.5 LR2D2, LR3D2 Separate mounting at 110 mm (4.33 in.) enters LA7D1064 DX1AP Mounting Holes LA7D2064 DX1AP Mounting Holes x Ø6.5 mm Srews x Ø6.5 mm Srews 2012 Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

46 Dimensions Table : TeSys D Thermal Overload Relay Dimensions, in. (mm) LRD Diret mounting beneath ontators with srew TeSys D Thermal Overload Relays Refer to 8502CT9901 LRD Diret mounting beneath ontators with spring terminal onnetions LC1 D09 D18 D25 D38 LC1 D b 4.84 (123) 5.39 (137) b 4.84 (123) See 8502CT9901 pages 122, 123. See 8502CT9901 pages 122, 123. LRD-3 Diret mounting beneath ontators LC1-D40 to D95 and LP1-D40 to D80 AM1 DL201 DL (17) d 0.28 (7) b e g(3p) g(4p) AC Control Ciruit LC1D (115.5) 4.88 (124) 3.03 (76.9) 0.37 (9.5) 0.87 (22) LC1D (115.5) 4.88 (124) 3.03 (76.9) 0.37 (9.5) DC Control Ciruit LC1D40, LP1D (111) 6.93 (176) 2.85 (72.4) 0.18 (4.5) 0.51(13) LC1D (111) 6.93 (176) 2.85 (72.4) 0.18 (4.5) LC1D65, LP1D (111) 6.93 (176) 2.85 (72.4) 0.18 (4.5) 0.51(13) LC1D80, D95, LP1D (115.5) 7.06 (179.4) 3.03 (76.9) 0.37 (9.5) 0.87(22) LRD4 Diret mounting beneath ontators LC1D115 and D150 LR9D Diret mounting beneath ontators LC1D115 and D150 a AM1DL200 and DR200 AM1DE200 and ED AM1DP200 and DR200 AM1DE200 and ED d 0.10 (2.5) 0.41 (10.5) d 0.10 (2.5) 0.41 (10.5) For additional speifiations and seletion information, see atalog 8502CT Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

47 Dimensions Table : TeSys F Overload Relay Dimensions LR9F5 71 Common side view TeSys F Overload Relays LR9F5 57, F5 63, F5 67, F5 69 Refer to 8502CT9901 qa Ø b a b Terminal shroud LA9F x 13.5 for LR9F5 57 and 8.5 x 13.5 for LR9F5 63, F5 67, F5 69 4xØ xØ5.5 LR9F7 75, F7 79, F7 81 Common side view LR9F7 81 (for mounting beneath LC1F630) f P1 P2 LR9F LR9F7 79, F Terminal shroud LA9-F70 P P Ø xØ Ø13 Diret mounting beneath ontator LC1F Diret mounting beneath reversing ontators or star-delta ontators H3 H1 b LA7F40 e Bus bar LA7F40p Bus Bar H2 H4 H3 H2 b LC1 ontators With LR9 relays b H1 H2 H3 LC1 ontators With LR9 relays b H4 H2 H3 F115 F5 57, F5 63, F5 67, F F115 F5 57, F5 63, F5 67, F F150 F5 57, F5 63, F5 67, F F150 F5 57, F5 63, F5 67, F F185 F5 57, F5 63, F5 67, F F185 F5 57, F5 63, F5 67, F F225 F F225 F F7 75, F F7 75, F F265 F F265 F F7 75, F F7 75, F F330 F7 75, F F330 F7 75, F F400 F7 75, F7 79, F F400 F7 75, F7 79, F F500 F7 75, F7 79, F F500 F7 75, F7 79, F F630 F F630 F d Relay mounting plate, see page e Connetion aessories, see page d 2012 Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

48 Dimensions TeSys D Combination and Non-ombination Starters Refer to 8502CT9901 Table : TeSys D Combination Starter Dimensions, Reversing and Non-Reversing NEMA 1 D09 25 (FVNR) D09 40 (FVR); D32-40 (FVNR) NEMA 12/3R R Provision for 1/4" Srew Provision for 1/4" Srew D09 25 (FVNR) D09 40 (FVR); D32-40 (FVNR) R R R Provision for 1/4" Srew Provision for 1/4" Srew Table : Non-Combination Starter Dimensions Non-Combination Starters A J K B R C E D D/2 Provision for 1/4" Srew F G H Type 1 Type 12/3R Non-Reversing Reversing A B C D E F G H J K D E D D40-65 D D80 D Note: All dimensions in inhes Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

49 Dimensions Table : TeSys K Contator Dimensions LR2K Diret mounting under the ontator TeSys K Contators Refer to 8502CT9901 Separate mounting with LA7-K0064 terminal blok on 35 mm rail (AM1DP200 or AM1DE200) x Ø Three-phase Wiring Sheme (DP200) (DE200) LC1, LP1, LP4K Mini-ontators On baseplate LA1-K A H Test Reset/Stop x Ø LC2, LC8, LP2, LP5K Reversing mini-ontators On baseplate LA1-K A1 A KM1 O KM1 A1 A x Ø Internal Links On AM1DP200 or DE200 rail (35 mm) On AM1DP200 or DE200 rail (35 mm) On printed iruit board On printed iruit board for reversing ontators or 2 mini-ontators side-by-side.34 9 A A1 A A x Ø x Ø A2 20 x Ø x Ø A2 LA2KT Eletroni time delay ontat bloks On mini-ontators or reversing mini-ontators LA2-KT Dual Dimensions: INCHES Millimeters Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

50 Dimensions Table : TeSys U Starter Dimensions Starter Controllers Non-Reversing TeSys U Motor Starters Refer to 8502CT0201 Reversing Rail Mounting Srew Mounting Rail Mounting Srew Mounting X2 X Ø Ø / / a 5.31 X X2 135a Note: a Minimum eletrial learane: X1: 35 mm for Ue 440 V; and 70 mm for Ue 500 and 690 V X2: 0 Maximum depth (with Modbus ommuniation module) Reversing Blok for Mounting Separately from Power Base Rail Mounting Srew Mounting Ø Limiter Disonnetor LUALB a 135a Maximum depth (with Modbus ommuniation module) Door interlok Mehanisms LU9AP00 Door Cut-out Ø Dual Dimensions: 4xØ INCHES Millimeters Ø Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

51 Dimensions Table : Altistart U01 and TeSys U Soft Starters TeSys U Combination (non-reversing power base) and ATSU01N212LT Mounting on (35mm) rail with VW3 G4104 onnetor Altistart U01 and TeSys U Soft Starters Refer to 8502CT9901 TeSys U Combination (non-reversing or reversing power base) and ATSU01N2206LT to ATSU01N212LT Side-by-side mounting TeSys U Combination (non-reversing power base) and ATSU01N222LT to ATSU01N232LT Mounting on (35mm) rail with VW3G4104 onnetor TeSys U Combination (non-reversing or reversing power base) and ATSU01N222LT to ATSU01N232LT Side-by-side mounting VW3G4104 Power Connetor Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

52 Dimensions TeSys Manual Starters and Protetors Refer to 2520CT0001 Table : TeSys GV2 and GV3 Manual Starter and Protetor Dimensions GV2M GV2AD, AM, AN, AU, AS, AX GV2AE Mounting of GV2M Blok GV2AD, AM, AN Blok GV2AU, AS, AX On 35 mm rail C 78.5 mm (3.09") on AM1DP200 (35 x 7.5 mm) C 86 mm (3.39") on AM1DE200, ED200 (35 x 15 mm) GV2P GV2AD, AM, AN, AU, AS, AX GV2AK00 Mounting of GV2P Blok GV2AD, AM, AN Blok GV2AU, AS, AX On 35 mm rail C 98.5 mm (3.88") on AM1DP200 (35 x 7.5 mm) C 106 mm (4.17") on AM1DE200, ED200 (35 x 15 mm) GV2AF4 + LAD31 GV2P + GV2GH7 GV2P + GV2GH7 + TeSys D ontator Combination GV2P + TeSys D range Combination GV2ME + TeSys D range ontator ontator for UL 508 Type E appliation for UL 508 Type E appliation b b d1 d (91.4) 3.6 (91.4) 3.8 (96.52) 3.8 (96.52) GV2ME + LC2D09 to D18 LC2D25 and D32 GV2P + LC2D09 to D18 LC2D25 and D32 b 7.4 (188.6) 7.8 (199) b 6.61 (168.1) 7.9 (199.5) (92.7) 3.9 (99) (116.8) 4.6 (116.8) 3.9 (98.2) 4.11 (104.5) 4.8 (122.3) 4.8 (122.3) d1 3.9 (98.3) 3.9 (98.3) d 4.1 (103.8) 1.4 (103.8) Surfae mounting enlosure GV2MC0 Flush mounting enlosure GV2MP0 (braket ut-out) a 2xØ5.3x b1 b a knok-outs for 16 mm plasti able glands or no. 16 onduit / GV2 b b1 in. mm in. mm MP01, MP MP03, MP Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In

53 Dimensions Table : TeSys GV2 and GV3 Manual Starter and Protetor Dimensions (ont d) TeSys Manual Starters and Protetors Refer to 2520CT0001 GV2M with GK2AF01 and LC1K GV2M with GV2AF01 and LC1K GV2M with GV2AF01 and LC2K Adapter Plate GK2AF01 Dimensions (mm) Ø ± ± Mounting external operator GV2AP0 Door ut-out GV2M on panel with GV2AF02 adapter plate 7.5 mm height ompensation plate GV1F / min.150 max Sets of bus bars, GV2G445, GV2G454, GV2G472 with terminal blok GV2G l p 4xØ Ø Sets of bus bars with terminal blok GV1G / / Sets of bus bars GV2G245, GV2G254, GV2G272 l I P GV2G x 1.8 in. (4 x 45 mm) 7.0 in. (179 mm) 1.8 in. (45 mm) GV2G x 2.1 in. (4 x 54 mm) 8.1 in. (206 mm) 2.1 in. (54 mm) GV2G x 1.8 in. (4 x 45 mm) 10.2 in. (260 mm) 2.8 in. (72 mm) I GV2G x 1.8 in. (2 x 45 mm) 3.5 in. (89 mm) GV2G x 2.1 in. (2 x 54 mm) 3.9 in. (98 mm) GV2G x 2.8 in.(2 x 72 mm) 4.6 in. (116 mm) GV2G x 2.1 in. (3 x 54 mm) 6.0 in. (152 mm) GV3P Dimensions Mounting on rail AM1 DE200 or AM1 ED X1 X (1) (2) X1 Eletrial learane (ISC max) 40 mm for Ue < 500 V; 50 mm for Ue < 690 V Mounting on panel, using M4 srews Bloks GV AN, GV AD, GV AM11 Blok GV3 AU and GV3 AS Mounting on pre-slotted mounting plate AM1PA 183 AF1 EA4 16 3xØ4 137,5 137, , ,7 18,7 Note: Leave a spae of 9 mm between 2 manual motor protetors: either an empty spae or side-mounting add-on ontat bloks. Horizontal mounting is possible: please onsult your regional sales offie Shneider Eletri This doument provided by Barr-Thorp Eletri Co., In