CROSS REFERENCE INDEX

Size: px

Start display at page:

Download "CROSS REFERENCE INDEX"

Brice Adams
5 years ago
Views:

1 arrier THIS DOUMENT AND THE INORMATION O NTAINED THEREIN IS PROPRIETARY TO ARRIER ORPORATION A ND SHALL NOT BE USED OR DISLOSED TO OTHERS, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION O ARRIER OR PORATION. SUBMISSION O THESE DRAWINGS OR DOU MENTS DOES NOT ONSTITUTE PART PERORMANE OR AEPTANE O ONTRAT ROSS REERENE INDEX PART. NO. MODEL DESRIPTION DESRIPTION INSTALLATION KIT NO. -00 NDL-93 (DOMESTI) UEL TANKS (22" DIAMETER) XX LIGHT BAR LED LIGHT BAR XX -01 NDL-93 RAIL EDITION (DOMESTI) -02 NDL-93 (AUSTRALIA) NOTES: -03 NDL-93 (EMEA) 1.0 OMPLETE INSTALLATION INLUDES AND IS NOT LIMITED TO: 1.1 UNIT INSTALLATION 1.2 BATTERY INSTALLATION, INLUDING DRAIN HOSE 1.3 OMPLETION O PRE-DELIVERY INSPETION (PDI)PER MODEL UNIT PREP AND INITIAL ADJUSTMENTS HEKLIST UNIT RUN IN PER PDI HEKLIST WARRANTY REGISTRATION ARD SUBMITTAL DATALINK DOWNLOAD VERIIATION 1.4 DEROST LINE ROUTING AND LAMPING 1.5 UEL LINE ONNETIONS TO UNIT 2.0 THE TRAILER OR BOXAR STRUTURE MUST BE EVALUATED BY THE TRAILER OR BOXAR MANUATURER TO DETERMINE IT'S ABILITY TO WITHSTAND THE LOADS IMPOSED BY THE UNIT OVER IT'S SERVIE LIE. ARRIER TRANSIOLD DOES NOT ONVEY ANY ENDORSEMENT OR WARRANTY OR THE TRAILER'S OR BOXAR'S STRUTURAL INTEGRITY. WEIGHTS: NDL X REEER UNIT (WET, LESS BATTERY): 1625 LBS NDL X2 2100, 2100A REEER UNIT (WET, LESS BATTERY): 1640 LBS NDL X2 2500A REEER UNIT (WET, LESS BATTERY): 1650 LBS BATTERY (TYPIAL): 50 LBS 3.0 UNIT MOUNTING SURAES O THE TRAILER OR BOXAR THAT ONTAT THE UNIT MOUNTING PADS MUST BE UNI-PLANAR TO WITHIN 0.13 [3] TO PENT DISTORTION O THE UNIT AND/OR TRAILER. 4.0 TRAILER OR BOXAR SURAES THAT ONTAT THE UNIT MOUNTING GASKET SHOULD NOT PROTRUDE MORE THAN 0.19 [5] ABOVE THE PLANE DEINED BY THE MOUNTING PAD SURAES TO ENSURE PROPER AIR SEAL. 5.0 ALL DIMENSIONS SHOWN ARE IN INHES, WITH THE METRI ONVERSIONS IN [MILLIMETERS]. ONTENTS GENERAL INORMATION 1 SWING RADIUS 2 UNIT DIMENSIONAL DATA, STD AND STEALTH 2 EVAP. BAK PANEL: TRAILER OR RAIL 3 TRAILER OR BOXAR PREPARATION 4 UNIT INSTALLATION 5 UNIT LITING LOATION 5 BATTERY INSTALLATION 6 HUTE DIMENSIONAL INORMATION 7 ISED BLOK TO INLUDE NDL-23 1/4/12 72N0081P11 E UPDATED INDEX, ADDED (PDI) TO NOTE 1.3. ORRETED UNIT NAMES AND WEIGHTS IN NOTE 2.0. IN ONTENT HART REMOVED BASI AND ULL ROM UNIT DIMENSION DATA, AND ORRETED SPELLING ERRORS. SEE S 4, 5 AND 6. 26OT2009 ZMG 72N251GP09 D ADDED -03 NDL-93 (EMEA). 23EB2009 ZMG 72N206GP09 INDEX B A UPDATED BLOK TO RELET MODELS OVERED. WAS EXTRA & ULTRA XT, ULTRA AND ULTIMA XT. UPDATED INDEX, ADDED BAK PANEL TO ONTENTS TABLE. ADDED 3, RENUMBERED S, SEE S 2 THRU 7. UPDATED INDEX, REMOVED EVAP BAK PANEL ROM ONTENTS TABLE DELETED 3, RENUMBERED S, SEE 2 THRU 7. 21APR2006 RS SHT.87 17APR2007 ZMG 72N217GP07 72N001GP06 SHT.55 - INITIAL RELEASE. 28EB2006 RS 72N022GN04 SYM ISION REORD DATE BY ENGR. M.E. NPA NO. IMPERIAL INH ORMAT: UNLESS OTHERWISE SPEIIED 1 O 7

2 arrier THIS DOUMENT AND THE INORMATION O NTAINED THEREIN IS PROPRIETARY TO ARRIER ORPORATION A ND SHALL NOT BE USED SUBMISSION O THESE DRAWINGS OR DOU MENTS OR DISLOSED TO OTHERS, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION O ARRIER OR PORATION. DOES NOT ONSTITUTE PART PERORMANE AEPTANE O ONTRAT OR [ ] MAX. OPEN POSITION ENTER O GRAVITY [948.9] HINGE PIN, SIDE DOORS 8.35 [212.1] [1066.8] [944.6] 1.26 HINGE PIN, SIDE DOORS [32.0] UNIT MOUNTING PADS [451.0] HINGE PIN RONT DOORS [914.4] R66.25 [1682.9] R60.74 [1542.9] R20.14 [511.6] 6.50 [165.1] R26.16 [664.5] [1102.0] MAX. OPEN POSITION R24.92 [633.0] [628.4] HINGE PIN RONT DOORS [787.1] [1949.2] [579.5] (74.75 ) DOOR TAPER [18.6] 8.17 [207.5] (ROM RAME STAND O PAD TO OUTSIDE EDGE O BAK PANEL) SWING RADIUS ALL UNIT VERSIONS [1149.4] [2177.1] 4.00 [101.6] (RETURN AIR DEPTH UNIT DIMENSION INORMATION ALL UNIT VERSIONS ISED BLOK TO INLUDE NDL-23 1/4/12 72N0081P11 UPDATED BLOK TO RELET MODELS OVERED. WAS: EXTRA & ULTRA XT, ULTRA AND ULTIMA XT. B MOVED REAR VIEW TO 3. 17APR2007 ZMG 72N217GP07 A ADDED REAR VIEW ROM 3. 21APR2006 RS 72N001GP06 SHT.55 DATE BY SYM ISION REORD ENGR. M.E. NPA NO. IMPERIAL INH ORMAT: UNLESS OTHERWISE SPEIIED PRINT DISTRIBUTION 2 O

3 arrier [1684.3] EVAP WIDTH THIS DOUMENT AND THE INORMATION O NTAINED THEREIN IS PROPRIETARY TO ARRIER ORPORATION A ND SHALL NOT BE USED SUBMISSION O THESE DRAWINGS OR DOU MENTS OR DISLOSED TO OTHERS, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION O ARRIER OR PORATION. DOES NOT ONSTITUTE PART PERORMANE AEPTANE O ONTRAT OR 1.60 [40.5] [782.3] SUPPLY AIR 2.87 [73.0] 4.92 [125.0] SUPPLY AIR [1149.4] [861.2] BAKPANEL 9.85 [250.1] RETURN AIR [1677.9] RETURN AIR WIDTH MOUNTING PADS (QTY 9) ROADSIDE NOTE: EITHER LOATION MAY BE USED BUT ROADSIDE LOATION OERS EASIER AESS. PLUG UNUSED HOLE ATER INSTALLATION (SEE SHT 4) THIS REAR VIEW OR STD. EDITION ONLY ISED BLOK TO INLUDE NDL-23 B SYM 1/4/12 72N0081P11 UPDATED BLOK TO RELET MODELS OVERED, WAS: EXTRA & ULTRA XT, ULTRA AND ULTIMA XT. NEW 17APR2007 ZMG 72N217GP07 DATE BY ISION REORD ENGR. M.E. NPA NO. THIS REAR VIEW OR RAIL EDITION ONLY IMPERIAL INH ORMAT: UNLESS OTHERWISE SPEIIED PRINT DISTRIBUTION 3 O

4 arrier THIS DOUMENT AND THE INORMATION O NTAINED THEREIN IS PROPRIETARY TO ARRIER ORPORATION A ND SHALL NOT BE USED OR DISLOSED TO OTHERS, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION O ARRIER OR PORATION. SUBMISSION O THESE DRAWINGS OR DOU MENTS DOES NOT ONSTITUTE PART PERORMANE OR AEPTANE O ONTRAT TRAILER OR BOXAR BODY PREPARATION 35.00[889] 70.00[1778] AUTION: UNIT MOUNTING SURAES O TRAILER OR BOXAR THAT ONTAT THE UNIT MOUNTI NG PADS MUST BE UNI-PLANAR TO WITHIN 0. 13[3] TO PENT DISTORTION O UNIT AND/OR TRAILER/BOXAR. AUTION: TRAILER OR BOXAR SURAES THAT ONT AT THE UNIT MOUNTING GASKET SHOULD NOT PROTRUDE MORE THAN 0.19[5] ABOVE THE PLANE DEINED BY THE MOUNTING PAD SURAES TO ENSURE PROP ER AIR SEAL [848] [1697] ALLOW 2.75" SPAE AROUND TRAILER OPE NING OR GASKET SEALING. (SEE AUTION NOT ES) 1.61 [41] 4.00[102] 6.44(164) 8.00 MAX [203] 4.00 MIN [102] 5.00 MAX./1.00 MIN. [127] [25] 4.61 [117] MOUNTING STUD, 1/2-13 UN GRADE [1011] [1168] INSULATION INSIDE LINER 4.60 [117] 7.00 [178] [576] 4.03 [102] 3.00 MAX MIN. [76] [64] (8)PLS VERTIAL & HORIZONTAL RAMING (THERMALLY NON-ONDUTIVE) [417] NOTE: EITHER LOATION MAY BE USED BUT ROADSIDE LOATION OERS EASIER AESS. PLUG UNUSED HOLE ATER INSTALLATION LIGHT BAR OPTIONAL (SEE DWG OR ) TRAILER OR BOXAR SIDE VIEW TYPIAL GLADHAND LOATION (TRAILER) TRAILER OR BOXAR RONT VIEW ISED BLOK TO INLUDE NDL-23 1/4/12 72N0081P11 E ADDED NOTE OR ENTER MOUNTING STUDS. ISED STUD LENGTH DIMENSION TO ADD MAX LENGTH. UPDATED BLOK TO RELET MODELS OVERED, WAS: EXTRA & ULTRA XT, ULTRA AND ULTIMA XT. 26OT2009 ZMG 72N251GP09 SYM ISION REORD DATE BY ENGR. M.E. NPA NO. IMPERIAL INH ORMAT: UNLESS OTHERWISE SPEIIED 4 O

5 arrier NOTE: BULKHEAD AND AIR HUTE SHOWN ARE OPTIONAL EATURES. OR BEST AIR IRULATION AND PRODUT PROTETION, ARRIER TRANSIOLD HIGHLY REOMMENDS THE USE O BULKHEADS AND AIR HUTES. ONTAT YOUR DEALER OR ARRIER TRANSIOLD OR REOMMENDATIONS UNIT LITING LOATION SEE NOTES 6.0 AND [152] MIN LEARANE OR SOLID BULKHEAD (TOP O LOOR TO BOTTOM O BULKHEAD) SEE NOTE 13 OR OPTIONAL BULKHEAD ONIGURATION SEE NOTE 9.0 SEE NOTE 8.0 SEE NOTE 11.0 UNIT INSTALLATION E MOVED ENDS O DRAIN LINE TO ORRET LOATION. UPDATED INSTALLATION NOTES 5.0 AND SYM UPDATED BLOK TO RELET MODELS OVERED, WAS: EXTRA & ULTRA XT, ULTRA AND ULTIMA XT. ISION REORD OR DISLOSED TO OTHERS, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION O ARRIER OR PORATION. DOES NOT ONSTITUTE PART PERORMANE AEPTANE O ONTRAT 1.0 PREPARE THE BODY TO REEIVE THE UNIT. DIMENSIONS OR EVAPORATOR AND MOUNTING STUD LOATIONS AN BE OUND ON 4 O THIS 2.0 REMOVE WIRE TIES HOLDING DEROST DRAIN HOSES, OOLANT OVERLOW TUBE, AND UEL LINES. PLAE LINES WHERE THEY WILL NOT BE AUGHT BETWEEN THE UNIT RAME AND THE MOUNTING SURAE. 3.0 OPEN SIDE DOORS TO ALLOW AESS TO MOUNTING STUD LOATIONS ON UNIT. 4.0 INSTALL BATTERY AORDING TO INSTRUTIONS ON 6. I UNIT HAS BEEN SUPPLIED WITH BATTERY, ONNET BATTERY ABLES AORDING TO THE INSTRUTIONS ON PREPARE THE UNIT OR LITING: STANDING ON A LADDER OR WORK-STAND, HOOK LITING APPARATUS (LITING SPREADER BAR WITH SUIIENT APAITY TO SUPPORT UNIT AND BATTERY) THROUGH THE LITING EYES. LIT POINT SHOULD BE ENTERED OVER THE UNIT. 6.0 RAISE THE UNIT AND INSTALL IN THE BODY. ENSURE THAT ALL EIGHT STUDS ARE ULLY ENGAGED IN THE UNIT RAME. PLAE WASHER (ITEM 70) AND LOK-NUT (ITEM 45) ON EAH O THE 8 STUDS. (NOTE: THE LOWER ENTER STUD MUST BE AESSED ROM THE RONT O THE UNIT.) SNUG THE NUTS, THEN EVENLY TIGHTEN ALL EIGHT TO 60 T-LB/81.6 NM USING A TORQUE WRENH. REMOVE LITING APPARATUS. 7.0 INSTALL BUTTON PLUGS (ITEM 92) IN UNIT RAME WHERE MOUNTING STUDS ARE LOATED AND ADDITIONAL UNUSED HOLE (SEE SHT.2). 8.0 ROUTE DEROST DRAIN HOSES DOWN THE RONT O THE TRAILER OR BOXAR AND TO RONT WALL USING 2 LAMPS (ITEM 15) AND 2 THREAD ORMING SREWS (ITEM 30) OR EAH DRAIN HOSE. UT HOSE TO PROPER LENGTH (APPROXIMATELY 3.00[76.2] ABOVE 5th-WHEEL PLATE ON TRAILER) AND INSTALL KAZOOS (ITEM 90) ON THE HOSES. 9.0 INSTRUTIONS OR UEL LINE ONNETION ARE SUPPLIED WITH THE UEL TANK KIT. INSTRUTIONS OR LIGHT BAR INSTALLATION ARE INLUDED WITH THE LIGHT BAR KIT. OR 1/4/12 72N0081P11 26OT2009 ZMG 72N251GP09 DATE BY ENGR. M.E. DRAWING. NPA NO. LAMP 10.0 PERORM PRE-DELIVERY INSPETION (ITEM 99). OPIES O OMPLETED HEKLIST SHOULD BE SUPPLIED TO SELLING DEALER AND USTOMER OPERATE UNIT IN ONTINUOUS RUN (MANUAL) MODE OR A MINIMUM O 8 HOURS (12 HOURS PREERRED) WITH REAR DOORS OPEN. PERORM INAL INSPETION ON UNIT IMPORTANT: PRIOR TO INAL DELIVERY TO USTOMER, WARRANTY REGISTRATION (ITEM 101) MUST BE OMPLETED. ONE OPY SHOULD BE PROVIDED TO THE USTOMER, ONE OPY TO THE SELLER, AND THE INAL OPY MUST BE SENT TO ARRIER TRANSIOLD. IN-SERVIE DATE MUST BE STAMPED ON THE UNIT IN THE PROPER LOATION (SERIAL NUMBER PLATE) TO ATIVATE WARRANTY OVERAGE OPTIONAL BULKHEAD ONIGURATION: HOLE PATTERN OR OPEN AREA OR RETURN AIR MUST TOTAL AT LEAST 2.75 T² O AIR PASSAGE. HOLE PATTERN OR OPEN AREA MUST BE REESSED SO THAT ARGO LOADED AGAINST BULKHEAD WILL NOT OBSTRUT AIR PASSAGE S. PERORATED BULKHEADS, THAT MEET THESE REQUIREMENTS, MAY BE INSTALLED TIGHT WITH LOOR. RETURN AIR SREEN REOMMENDED DRAIN LINES SUPPLIED WITH REEER UNI T, UT TO SUIT. (DO NOT KINK OR OTHERWISE LOSE DOWN TUBE I.D.) ISED BLOK TO INLUDE NDL-23 SUBMISSION O THESE DRAWINGS OR DOU MENTS ATER INSTALLATION EVAPORATOR AIR PROPRIETARY TO ARRIER ORPORATION A ND SHALL NOT BE USED UNIT INSTALLATION: ONDENSER AIR 4.00[102] BULKHEAD INSIDE THIS DOUMENT AND THE INORMATION O NTAINED THEREIN IS PREPARE UNIT OR INSTALLATION: ONDENSER AIR (RONT AE ONLY) 90 IMPERIAL INH ORMAT: UNLESS OTHERWISE SPEIIED PRINT DISTRIBUTION LOW 5 O

6 arrier THIS DOUMENT AND THE INORMATION O NTAINED THEREIN IS PROPRIETARY TO ARRIER ORPORATION A ND SHALL NOT BE USED OR DISLOSED TO OTHERS, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION O ARRIER OR PORATION. SUBMISSION O THESE DRAWINGS OR DOU MENTS DOES NOT ONSTITUTE PART PERORMANE OR AEPTANE O ONTRAT SREW, HXHD 5/16-18 X 11" LG TORQUE 5-6 T/LBS WASHER, LOK 5/16" SPRING UNITS SUPPLIED WITH BATTERY INSTALLED 1.0 UT WIRE TIE(S) THAT HOLD BATTERY ABLES TO UNIT RAME. WASHER, PLAIN 5/16" 2.0 ONNET RED BATTERY ABLE TO THE POSITIVE (+) BATTERY TERMINAL; ONNET BLAK ABLE TO NEGATIVE (-) BATTERY TERMINAL (USE O ORROSION INHIBITOR IS REOMMENDED). 3.0 POSITION TERMINAL OVERS SUPPLIED WITH ABLES OVER TERMINALS. 4.0 INSTALL DRAIN HOSE (ITEM 6) TO BARB ON BOTTOM O BATTERY TRAY USING LAMP (ITEM 5). ROUTE AND LAMP HOSE TO UNIT DRAIN LINE USING WIRE TIES (ITEM 55). ANGLE BATTERY HOLD DOWN UNITS SUPPLIED WITHOUT BATTERY INSTALLED 1.0 USE THE OLLOWING INORMATION TO ORRETLY SELET THE BATTERY PERORMANE NEEDED OR RERIGERATION UNITS. GROUP SIZE: GROUP 31 VENT LOATION: SIDE VENT VOLTS: 12 VOLTS D AMPERAGE: MINIMUM 700 OLD RANKING 0 MINIMUM 545 OLD RANKING -20 NOTE: WHEN SELETING A SPEII BRAND O BATTERY, ALWAYS ENSURE THAT THE BATTERY HOSEN IS RATED AT 0 (0 DEGREES AHRENHEIT) AND NOT 0 (0 DEGREES ELSIUS). AILURE TO USE THE PROPER BATTERY SIZE WILL RESULT IN REDUED BATTERY LIE AND A NO-START ONDITION. ITEMS SUPPLIED IN BATTERY KIT (PARTS IN POLY BAG AND/OR ATTAHED T O BATTERY TRAY) 2.0 UT WIRE TIE HOLDING THESE PARTS IN THE BATTERY TRAY AND REMOVE PARTS. PLAE BATTERY IN TRAY WITH NEGATIVE (-) TERMINAL TO THE REAR O THE UNIT (AS SHOWN). ONNET BATTERY ABLES (THE USE O A ORROSION INHIBITOR ON THE TERMINALS IS REOMMENDED); RED ABLE TO POSITIVE (+) TERMINAL, BLAK ABLE TO THE NEGATIVE (-) TERMINAL. ABLES SHOULD BE ROUTED TOWARD THE OMPRESSOR (AS SHOWN). TIGHTEN TERMINAL ONNETORS SEURELY. 3.0 INSTALL SREWS AND HOLD-DOWN HANNEL USING PLAIN AND LOK WASHERS AS SHOWN. SEURELY TIGHTEN THE SREWS TO PENT MOVEMENT O THE BATTERY. 4.0 POSITION TERMINAL OVERS SUPPLIED WITH ABLES OVER TERMINALS. 5.0 INSTALL DRAIN HOSE (ITEM 6) TO BARB ON BOTTOM O BATTERY TRAY USING LAMP (ITEM 5). ROUTE AND LAMP HOSE TO UNIT DRAIN LINE USING WIRE TIES (ITEM 55). 6 5 ISED BLOK TO INLUDE NDL-23 1/4/12 72N0081P11 E MOVED ENDS O DRAIN LINES TO ORRET LOATION. 26OT2009 ZMG 72N251GP09 UPDATED BLOK TO RELET MODELS OVERED, WAS: EXTRA & ULTRA XT, ULTRA AND ULTIMA XT. SYM ISION REORD DATE BY ENGR. M.E. NPA NO. IMPERIAL INH ORMAT: UNLESS OTHERWISE SPEIIED 6 O

7 arrier THIS DOUMENT AND THE INORMATION O NTAINED THEREIN IS PROPRIETARY TO ARRIER ORPORATION A ND SHALL NOT BE USED OR DISLOSED TO OTHERS, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION O ARRIER OR PORATION. SUBMISSION O THESE DRAWINGS OR DOU MENTS DOES NOT ONSTITUTE PART PERORMANE OR AEPTANE O ONTRAT NOTE: BULKHEAD AND AIR HUTE SHOWN ARE OPTIONAL EATURES. OR BEST AIR IRULATION AND PRODUT PROTETION, ARRIER TRANSIOLD HIGHLY REOMMENDS THE USE O BULKHEADS AND AIR HUTES. ONTAT YOUR DEALER OR ARRIER TRANSIOLD OR REOMMENDATIONS. TRANSITION & HUTE DETAILS 2.00 [51] MINIMUM W 2.00 [51] MINIMUM 45 MINIMUM TRANSITION ANGLE H TRANSITION DUT HUTE EVAPORATOR OUTLET NOZZLE SALE [51] MINIMUM ROM BOTTOM EDGE O EVAPORATOR NOZZLE TO TRANSITION OR HUTE HUTE TRANSITION HARD RETANGULAR HUTE MIN. DIMENSIONS W H W1 H1 SALE EVAPORATOR OUTLET NOZZLE HUTE SOT HUTE MINIMUM DIMENSIONS HUTE REMOVED OR LEARIIATION O TRANSITION ISED BLOK TO INLUDE NDL-23 1/4/12 72N0081P11 UPDATED BLOK TO RELET MODELS OVERED, WAS: EXTRA & ULTRA XT, ULTRA AND ULTIMA XT. B 7 WAS 6. PIT. ISED BAK PANELS. 17APR2007 ZMG 72N217GP07 W1 H A 6 WAS 7, PIT. ISED BAK PANELS. 21APR2006 RS 72N0001GP06 SHT.55 SYM ISION REORD DATE BY ENGR. M.E. NPA NO. IMPERIAL INH ORMAT: UNLESS OTHERWISE SPEIIED 7 O

CROSS REFERENCE INDEX

Carrier DOES NOT CONSTITUTE PART PERFORMANCE OR CROSS REFERENCE INDEX PART. NO. MODEL DESCRIPTION DESCRIPTION INSTALLATION KIT NO. 00 VECTOR 5100 (DOMESTIC) STANDBY ONLY LED LIGHT BAR 03246 760200000 01