quick reference manual

Transcription

1 quick reference mnul For the leo modules with stndrd frmes 50mm S18 S19 S25 S59 S75 S79 with stndrd frme 35mm P18 P19 with frmes for roof integrtion S18 sol S19 sol S79 sol Plese red this crefully prior to instlltion. Store in sfe plce for mintennce. Copyright 2015 leo solr GmbH leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, en-gb-de (1) JD EN

2 1 This mnul in other lnguges 2 Product support Deutsch (de-de) English (en-gb) Frnçis (fr-fr) Itlino (it-it) Nederlnds (Benelux) (nl-be) Ελληνικ (el-gr) Wenn Sie diese Kurznleitung in deutscher Sprche benötigen, wenden Sie sich bitte n leo solr, siehe Kp If you require this quick reference mnul in English, plese contct leo solr, see chp Pour voir cette notice d instlltion en Frnçis contctez leo solr (voir chpitre 2.2). Ove necessitste delle seguenti istruzioni d uso in lingu itlin, voglite gentilmente rivolgervi leo solr, vedi cp 2.2. Wenst u deze hndleiding in het Nederlnds te ontvngen, neem dn contct op met leo solr zie hoofdstuk 2.2. Εάν χρειάζεστε αυτό το εγχειρίδιο στα Αγγλικά, παρακαλώ επικοινωνήστε με την leo solr, βλ. κεφάλαιο Detiled informtion In ddition to this Quick Reference Mnul, leo solr lso provides further informtion on its website. 2.2 Contct leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny T +49 (0) F +49 (0) E info@leo-solr.com W Copyright 2017 leo solr GmbH This Quick Reference Mnul is protected by copyright. All rights reserved. Copying, reproduction, trnsltion, or conversion to ny type of electronic medi or mchine redble form, in its entirety or prts, is not permitted. An exception will be mde for bckup copy for your own use. leo solr reserves the right to chnge this document withhout prior notice. leo nd leo solr re registered, protected trdemrks of leo solr GmbH. Pge 2/20 leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN

3 3 Tble of content 1 This mnul in other lnguges Product support Detiled instructions Contct Copyright Explntion of sfety guidelines Wrnings nd notes in this mnul Notes on modules About this mnul Detiled informtion for instllers nd plnners Hndling leo modules Intended use Personl protection Screw mounting Insertion mounting Lod levels Key to symbols Mounting drwings for modules with stndrd frmes For opertors: mintennce Inspections Review Detils for the inspections Clening Repirs For opertors: decommissioning Sfety precutions Disposl Returns PV Cycle Prepring for instlltion Hndling leo modules Sfety precutions Electricl connections Mechnicl Instlltion Mounting orienttion for modules Sfety precutions Improper mounting Intervls Avoiding sels Clernce under the modules Shdowing Electricl instlltion Connectors Lying the string cbles Potentil equlistion (erthing) of module frmes Lightning protection Detils of mechnicl mounting Aligning the mounting profiles Clmp mounting for modules with stndrd frmes Clmp mounting for modules with Solrif frmes leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN Pge 3/20

4 4 Explntion of sfety guidelines This is the dnger symbol. It is used in severl versions in this mnul to lert you to the potentil risk of personl injury. 4.1 Wrnings nd in this mnul The dnger wrnings re structured s follows: Type nd source of dnger. Possible consequences of non-observnce. Mesures or prohibitions to void the dnger. DANGER! DANGER indictes n imminently dngerous sitution which inevitbly leds to deth or serious injury if not voided. The informtion on wrning nd cutions is structured s follows: Type nd source of dnger. Possible consequences of non-observnce. Mesures or prohibitions to void the dnger. WARNING! WARNING indictes potentilly dngerous sitution which cn led to deth or serious injury if not voided. CAUTION! CAUTION indictes potentilly dngerous sitution which cn led to slight or semi-serious injury if not voided. indictes potentilly dngerous sitution which cn cuse mteril dmge if not voided. 4.2 Notes on modules The following symbol is ttched to the modules: If this symbol lso ppers on dnger or wrning product lbel, it is wrning you of the dnger cused by electric current or voltge which cn led to per sonl injury if you fil to observe the instructions. 5 About this mnul This Quick Reference Mnul is relese 4.3 with the issue dte 07/2017. The publiction of this mnul renders ll previous releses (older thn relese 4.3) of this mnul invlid. leo solr constntly strives to improve its products nd their documenttion. Therefore, we dvise you to use the ltest version of the mnul t ll times. Hnd over this Quick Reference Mnul to the opertor fter instlltion nd ensure you hve confirmtion of receipt. 5.1 Detiled informtion for instllers nd plnners Informtion on the leo solr website You cn find the ltest relese of the Quick Reference Mnul nd dditionl informtion on leo solr s website: Alwys use the ltest version for your modules if you find more recent relese of the mnul Informtion sources for opertors If you hve ny queries bout the ltest relese, contct your leo solr specilist prtner or leo solr directly (see Ch. 2.2: Contct ). 6 Hndling leo modules 6.1 Intended use Approprite use leo modules re used for generting electricl power in sttionry, photovoltic systems which re connected to the grid. If you would like to use the modules for nother purpose, such s for chrging n ccumultor directly, you my need dditionl components (e.g. string diodes). leo modules re suitble for instlling ner livestock frms nd costl regions. Observe ll the pplicble legisltion, regultions, guidelines nd stndrds when instlling nd operting the modules Inpproprite use Do not instll leo modules on vehicles nd do not use them in ir, spce or sefring pplictions. Do not use leo modules if they re exposed to con centrted sunlight or strong rtificil light, or if they could be immersed in wter or other liquids or expo sed to vpour Product-specific informtion Product-specific informtion (e.g. the dt sheet) contins detils of prticulr type of module. Only use leo modules for the intended purpose outlined in the product-specific informtion. Pge 4/20 leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN

5 This module is rted for use in ppliction clss A ccording to iec 61. For the electricl dt plese refer to the dt sheet or the nme plte. Under norml conditions, solr modules re likely to experience conditions tht produce more current nd/or voltge thn reported t stndrd test conditions. 1 Accordingly, the vlues of I SC nd V OC mrked on the modules should be multiplied by fktor of 1.25 when determining component voltge rtings, conductor mpcities, fuse sizes, nd size of controls connected to the PV output. Dt sheets my chnge without prior notice. If the informtion in the dt sheet differs from this mnul, the dt sheet tkes precedence 6.2 Personl protection Electricl sfety precutions DANGER! High DC voltges during storge, instlltion, opertion nd mintennce. Risk of ftl electric shock! leo modules my only be instlled by qulified technicins with high level of expertise. DANGER! Dngerous, high DC voltges generted even t low levels of light, especilly in series connection. Risk of ftl electric shock! Never touch the electricl connections of solr module under ny circumstnces, not even if you hve disconnected the photovoltic genertor. DANGER! Electric rcs form when electricl connections re mde or disconnected incorrectly. Severe or ftl injuries from electric shock or severe injury from burns! Before you crry out ny work on electricl compo nents, disconnect the photovoltic genertor. DANGER! Contct with live prts due to defective insultion or dmged/fllen off junction box covers. Severe or ftl injuries from electric shock! Do not touch dmged prts with your bre hnds. Use protective clothing nd suitble, insulted tools. DANGER! High DC voltges, even when the photovoltic genertor is disconnected if the genertor is erthed. 1 E.g. in the event of strong solr irrdition, low mbient temperture, nd reflections from snow. Severe or ftl injuries from electric shock! If the circuit of your photovoltic genertor is erthed, remove the erth before you crry out electricl work on the genertor. WARNING! Contct with live prts due to unsuitble tools or wether conditions. Risk of electric shock! Only use pproved, insulted tools for mintennce work on live prts. Work in dry conditions. Ensure tht the electricl connections of the solr module, the cbles nd the tools, re dry. RECOMMENDATION Work in pirs so tht in n emergency one person is ble to help in the cse of injury. This is becuse the modules generte voltge s soon s they re exposed to light. Therefore, prts of the system re nerly lwys energised during the dytime Mechnicl sfety precutions WARNING! Glss cn crck, brek or splinter. Bewre of injury! Never step or sit on solr modules. Avoid knocking nd bumping the surfce, the edges nd corners of the glss pnels. WARNING! Exposed live prts due to dmged glss. Risk of electric shock! Only use modules with the insultion in perfect condition. CAUTION! Shrp glss edges or flying glss splinters. Bewre of injury! Alwys use suitble protective equipment (e.g. gloves nd goggles). Be especilly creful with the glss edges nd corners of lmintes (frmeless modules). Insulting bck sheet WARNING! Dmged insulting bck sheet. Risk of electric shock nd burns! Avoid ny contct with the bck of the module with shrp or pointed objects. Ensure tht the bck sheet remins undmged. leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN Pge 5/20

6 7 Prepring for instlltion Trnsporting modules to the instlltion site 7.1 Hndling leo modules Storing modules Frmed modules Modules in pckging units: Store the leo modules upright in the pckging units. Mke sure tht ech module hs sufficient support. Do not stck the pckging units. This could dmge the modules. Individul modules: Store individul leo modules in n upright position on wedges with suitble pdding. Use dequte pd ding between the individul modules. Avoid stcking individul modules, s well s the pllets they rest on Unpcking modules Frmed modules Using n underly, incline the pllet (e.g. with bem, height pprox. 10 cm for 5 inclintion), so tht the opening on the front of the box is elevted. The modules then len bck in the box which mkes it esier to remove them. Use n underly for inclining which supports the whole side of the pllet (e.g. bem). This keeps the modules supported in the box long their entire width. Remove the module from this side only. Remove the module with the help of nother person, if possible. Observe the unpcking instructions on the module box Checking modules Before instlltion, check ech leo module formechnicl defects. Py prticulr ttention to possible dmge to glss pnels nd insulted bck sheets. In ddition, check the insultion on the cbles, connectors nd junction boxes. If you discover ny defects, report them to the supplier or trnsport compny immeditely. Frmed modules Alwys crry the leo module with one other per son. Tke hold of the module on its long sides. When trnsporting individul modules, mke sure tht you do not put ny strin or pressure on the junction box nd cbles. 7.2 Sfety precutions DANGER! When instlling on roofs or other elevted sites, objects my fll down. Severe or ftl injuries re possible! Block off the dnger zone for people nd nimls before beginning instlltion work. If possible, remove ll objects from the dnger zone. DANGER! Electric rcs form when electricl connections re mde or disconnected incorrectly. Severe or ftl injuries from electric shock or severe injury from burns! Disconnect the photovoltic genertor before you crry out ny work on the electricl components of the photovoltic genertor. DANGER! High DC voltges, even when the photovoltic genertor is disconnected, if the genertor is erthed. Severe or ftl injuries from electric shock! If the circuit of your photovoltic genertor is erthed, remove the erth before crrying out electricl work on the genertor. WARNING! Exposed live prts on dmged modules. Dnger of electric shock! Only use components which re in perfect condition for use in photovoltic systems. Do not instll solr modules with visible dmge to the glss pnels, the insulting bck sheet or on the insultion of electricl connections. Pge 6/20 leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN

7 WARNING! Contct with live prts due to unsuitble tools or wet conditions. Dnger of electric shock! Only use pproved, insulted tools for instlltion or mintennce work on live prts. Work in dry conditions. Mke sure tht the electricl connections on the solr module, the cbles used for instlltion nd the tools, re dry Inclintion Incline the surfce of the modules t n ngle of t lest 10 horizontlly, so tht precipittion cn drin off which supports the modules self-clening. For optimum self-clening, we recommend n ngle of t lest 15 horizontlly Helth nd sfety CAUTION! Risk of slipping due to wind, rin, snow or ice. Risk of injury due to flling or colliding with objects! Avoid unfvourble wether conditions, such s strong wind or rin. Also void working on the instlltion site in ice nd snow. Use the sfety equipment required or recommended by locl regultions, such s hrd hts, steel-cpped shoes with rubber soles, protective goggles, gloves or fll-protection systems. CAUTION! Hot module prts in strong sunlight. Risk of burning! Protect yourself from burning by wering gloves nd suitble clothing. 7.3 Electricl connections For modules connected in series, only leo modules with sme current rting must be use together For modules connected in prllel, only leo modules with the sme voltge rting must be some together The module must be not operted t higher voltge thn the permissible system voltge 8 Mechnicl Instlltion 8.1 Mounting orienttion for modules Verticl (portrit) mounting When mounting the module verticlly, mke sure tht the cbles re fcing towrds the ground nd the junction box is fcing upwrds Horizontl (lndscpe) mounting When mounting horizontlly, mke sure tht the exit holes for the cbles on the module or the junction box re positioned on the inside of the photovoltic genertor. Avoid the lterl outer edges of the photovoltic genertor to minimise the effect of mbient conditions, such s wind or rin. Fig.1 Recommended position of the junction boxes for horizontl mounting (fcing the middle of the genertor) 8.2 Sfety precutions Do not drill ny dditionl holes in leo modules or their frmes. 8.3 Improper mounting Do not ttch the modules using nils. The vibrtion creted in the process cn cuse micro fissures nd loss of yield, nd results in loss of wrrnty rights. Do not ttch the modules by welding. The tempertures creted in the process cn cuse delmintion, micro fissures nd loss of yield, nd results in loss of wrrnty rights. 8.4 Intervls Intervls between modules with stndrd frmes Leve minimum clernce when mounting modules. This prevents mechnicl tension due to therml expnsion. When mounting t intervls Leve clernce of 3 mm or more between the individul module frmes. For edge-to-edge mounting Allow for n expnsion joint of 20 mm fter mximum of 7 m. leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN Pge 7/20

8 The recommended mximum clernce is 30 cm, bsed on the modules stndrd cble length. leo solr recommends mounting t intervls. Also note the informtion from the mounting equipment vendor. This could specify lrger intervls Clernce under the modules Minimum clernce Rooftop or freefield mounting Ensure clernce of t lest 4 cm between the rer edge of the frme nd the mounting surfce (e.g. the roof tiles) for the rer ventiltion ofthe leo module. Roof-integrted mounting Ensure n pproprite intervl, for exmple, to the trough of the mounting system. Also ensure dequte ridge ventiltion, for exmple, with roof ridge ventiltor. Mximum clernce The lrgest permissible clernce is defined by ntionl stndrds. This is used to design the instl ltion on the ssumed effects of wind nd suction. The ctul mximum clernce of n instlltion is determined by the sub-structure. Ensure tht your sub-structure dheres to the permissible clernces. 8.5 Avoiding sels Avoid the use of sel between leo modules nd their mounting surfce. Dry nd cool opertion cn hve positive effect on the performnce s well s the service life of n leo module. Also for roof-integrted mounting, ensure good rer ventiltion to minimise loss of output which results from higher module temperture. Ensure dequte ridge ventiltion, for exmple, with roof ridge ventiltor. 8.6 Clernce under the modules Keep the spce behind the lminte free of ny objects. This prevents dmge to the insulting bck sheet nd the junction box. Ensure tht shrp or conductive prts (e.g. screws or nils) do not protrude into the spce behind the module. If possible, tke mesures to prevent foreign objects (e.g. snow, ice, leves, twigs, brnches from being ble to get behind the module. 8.7 Shdowing Avoidnce of shdowing Avoid shdowing of solr modules. This pplies lso nd especilly for shdowing of smll res due to close smll objects like ntenns or lightning protectors. If there is systemticl shdowing in the course of the dy or yer becuse of djcent objects t the site nd you do not hve ny opportunity to ffect the shdowing, then: - tke nother site into considertion - only pln with the non-shdowed prts of your site when you configure your photovoltic-genertor Effects of shdowing Even shdowing of single module or solr cell cn pprecibly ffect the power output of your photovoltic plnt. If shdow flls on single solr modules of photovoltic genertor or on single solr cells of solr module, the shdowed prts generte less or no electricl power nymore. This my ffect the yield of the whole module string nd therefore the whole genertor. Furthermore, shdowing often cuses the solr cells to consume the otherwise in the module generted electricl power. This my cuse wrming of the shdowed cells in comprison to the not shded cells, which in extreme cses cn rise the risk of fire. Constnt or systemtic shdowing cn cuse serious yield loss nd my ccelerte the ging process nd therefore cuses power loss or filures of the photovoltic genertor. Avoid shdowing e.g. cused by building prts, depending on dy time or seson (esp. in winter) to optimize the yield nd durbility of your plnt Protective devices of the modules Aleo modules re equipped with bypss-elements to limit the temperture rising becuse of the internl power consumption induced by shdowing to non-criticl grde nd thus protect the module. Avoid systemtic shdowing lso becuse the bypss-elements re not suited for constnt, long lsting lods. Pge 8/20 leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN

9 9 Electricl instlltion 9.1 Connectors WARNING! Incomptible or unsuitble connectors cn overhet. Fire hzrd! Only use connectors tht re the sme type nd from the sme mnufcturer. Avoid using different types of connectors or ones from different mnufcturers, even: - if connecting is possible - if the connectors hve the sme bsic designtion (e.g. MC4 ) or - if they re designted s comptible. You cn find more detils on this in the next two sections Module connectors The vrious module types cn be fitted with the following connectors: Originl Multicontct MC4 (with locking) PV-JM601 (with locking) You cn find the specific connectors in the module dt sheet Connector peculirities Originl Multicontct MC4 connectors Only plug originl Multicontct MC4 connectors into originl Multicontct MC4 connectors. 2 PV-JM601 connectors Only plug PV-JM601 connectors into PV-JM601 connectors. Avoid ny tensile nd pressure lods on the junction box when mounting. When mounting, void hevy tensile lods on ny connectors lredy plugged in. Bend the cbles from the connector t lest 4 cm fter they exit from the connector. Bend the cbles from the junction box s well, t lest 4 cm fter they exit from the connector. This keeps the cbles wterproof t the cble outlet. Observe the guidelines on lying the respective cbles. Ly ll cbles ensuring tht: You dhere to the minimum bend rdius (e.g. 5-fold cble dimeter3). You void lying ner shrp corners nd edges or protect the cbles ccordingly. cbles must not ly between module bckside nd mounting system prts. You protect them from direct sunlight nd precipittion. You secure the cbles with UV resistnt cble clips 4 or other suitble cble fsteners which protect the cble insultion. Cbles from module strings re lid s ner to ech other s possible to minimise the effects of being struck by lightning Wether protection Ly the cbles so tht they exit the junction box from below. This prevents wter, which runs long the cble, from collecting t the point where the cbles exit the junction box. For modules mounted horizontlly, ly the cbles in U-form wy from the junction box. Modules mounted verticlly do not usully need ny dditionl djustments Replcing the connectors You cn remove the connector on module nd replce it with nother connector, if necessry. You retin the mnufcturing wrrnty if you remove nd mount with pproved tools in the proper wy nd ccording to the connector mnufcturer s instructions. 9.2 Lying the string cbles CAUTION! Brittle frctures in junction boxes due to contct with unsuitble connection cbles: Risk of fire! Only use connection cbles without plsticisers. 2 The originl Multicontct MC4 connectors re referred to s MC4 in the dt sheet. Fig.2 U-form cbles t the junction box for horizontlly mounted module 3 Some countries specify lrger bend rdius, e.g. 8-fold wire dimeter in the USA (NEC Codebook 2011). 4 For ttching the cble clip, use suitble tool which cn fully tighten t defined low force. Avoid cble clips nd tools which constrict or dmge the cble insultion when tightening. leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN Pge 9/20

10 Ly cbles crefully to protect ginst dmge from: Direct environmentl fctors, such s precipittion movement (e.g. from wind) Indirect environmentl fctors, e.g. snow or ice, which slip down behind the modules, nd Chffing on the insultion due to the cble moving (e.g. from wind or ice). 10 Detils of mechnicl mounting 10.1 Aligning the mounting profiles Permissible lignment Potentil Lightning equlistion protection(erthing) of module frmes 10.2 Clmp mounting for modules with stndrd frmes WARNING! Fig Permissible Arrnging the lignment clmps of mounting profiles Locl Absence regultions of or indequte my specify lightning potentil protection., b: Prllel profiles for mounting; c: Prllel, ligned equlistion Risk of fire or (erthing). electric shock! fingers Permissible of mounting rrngement system. When Leve erthing the plnning the module nd instlltion frme, estblish of the externl, sfe electricl nd if required connection internl, to the lightning erth protection potentil or to be Impermissible lignment erthed crried out sub-structure. by qulified technicins t ll times. Observe It is essentil the requirements to integrte n nd rrestor recommendtions for connecting of the the lightning inverter rod mnufcturer, with the lightning s well protection. s insurnce This policies. ensures the sfety nd relibility of the lightning protection The module s well frmes s the re photovoltic mde of luminium. system. When GID AS024 mounting onto other mterils, tke suitble mesures Do not under to prevent ny circumstnces electric corrosion, include e.g. the module by Fig.5 55Permissible clmp rrngement for frmed using frme or coting. its erth s n ctive prt of the lightning modules protection (e.g. s lightning rrestor). Fig.4 : Symmetricl Impermissible clmping lignment on the long of mounting sides, b: Asymmetricl profiles : clmping Profiles on the not long prllel sides (cceptble to one nother; for certin lod levels), c: Symmetricl clmping on the short sides. b: Profiles neither prllel nor perpendiculr to the Potentil If you erth equliztion the module does frme, not serve the only s tsk lightning of this module Impermissible edges; rrngement 9.4 Lightning protection. erth is protection the Lightning potentil protection equlistion my between necessry the mod-10.ule ddition frme to nd potentil the supporting equliztion. structure. connected. c: Clmp The profile mounting ends for modules the sides with of module stndrd re not in frmes 9.4 Lightning WARNING! protection 10.2 Clmp mounting for modules with stndrd frmes 10 Detils of mechnicl mounting Arrnging the clmps Absence of WARNING! or indequte lightning protection Arrnging the clmps 10.1Risk Aligning of fire or the electric mounting shock! profiles Permissible rrngement GID AS025b Leve Absence the plnning of or indequte nd instlltion lightning of protection. the externl, Permissible rrngement nd Risk if required of fire or internl, electric shock! lightning protection to be Fig.6 55Impermissible clmp rrngement for frmed Permissible lignment crried out by qulified technicins t ll times. modulespermissible clmp rrngement for Leve the plnning nd instlltion of the externl, frmed modules It is nd essentil if required to integrte internl, n lightning rrestor for protection connecting to be Impermissible clmp rrngement for frmed modules the crried lightning out rod by with qulified the lightning technicins protection. t ll times. This (1): Missing clmps, b, c: Clmping on both short nd long ensures the sfety nd relibility of the lightning protection s well s the photovoltic system. It is essentil to integrte n rrestor for sides. GID GID AS024 AS024 connecting the lightning rod with the lightning Do protection. not under ny This circumstnces ensures the sfety include nd the relibility module Fig.5 Fig.5 55Permissible clmp clmp rrngement for for frmed frme of the or lightning its erth s protection n ctive s prt well of s the the lightning modules protection photovoltic (e.g. s system. lightning b rrestor). c GID AS022b : Symmetricl : Symmetricl clmping clmping on the long sides, the long b: Asymmetricl sides, Fig.3 Permissible lignment of mounting profiles Do not under ny circumstnces include the clmping on the long sides (cceptble for certin lod b: Asymmetricl clmping on the long sides, b: Prllel module profiles frme for or mounting; its erth s c: n Prllel, ctive ligned prt of the levels), c: Symmetricl clmping on the short sides. (cceptble for certin lod levels), fingers lightning of mounting protection system. GID AS069b (e.g. s lightning rrestor). d e f c: Symmetricl clmping on the short sides. If you erth the module frme, the only tsk of this Impermissible rrngement erth the potentil equlistion between the module frme d: Fig.7 Clmping Impermissible on both clmp short rrngement nd long sides. for frmed Impermissible lignment nd the supporting structure. modules (2) d: Protruding clmps, e: Opposing clmps hve different 10 distnces to the module corners, f: Asymmetricl clmps on Detils If you erth of mechnicl the module frme, mounting the only tsk of this the short sides. erth is the potentil equlistion between the 10.1 module frme nd the supporting structure. Aligning the mounting profiles Clmp dimensions GID AS025b GID AS023b Fig.6 Observe 55Impermissible the following informtion clmp rrngement for clmp for lengths frmed nd Permissible lignment Fig.4 Impermissible lignment of mounting profiles depths. modulespermissible clmp rrngement for frmed modules : Profiles not prllel to one nother; b: Profiles neither prllel 10/20 nor perpendiculr to the module edges; c: The profile Impermissible leo solr GmbH Mrius-Eriksen-Strße clmp rrngement for Prenzlu frmed Germny modules info@leo-solr.com Pge (1): Missing clmps, b, c: Clmping Quick on Reference both Mnul short Rel. nd 4.3, long 07/2017, EN ends for the sides of module re not connected. GID AS022b

11 Impermissible rrngement Fig.6 Impermissible clmp rrngement for frmed modules Permissible clmp rrngement for frmed modules Impermissible clmp rrngement for frmed modules(1) : Missing clmps, b: Clmping on both short nd long sides. Fig.7 Impermissible clmp rrngement for frmed modules (2) d: Protruding clmps, e: Opposing clmps hve different distnces to the module corners, f: Asymmetricl clmps on the short sides Clmp dimensions Observe the following informtion for clmp lengths nd depths. Clmp lengths nd depths Depending on the mbient conditions (e.g. ngle, suction lod or tolernces of the substructure) higher minimum re per clmp my be required. The clmps determine the ctul clmp depth nd length. Observe the instructions of the clmp mnufcturer Tightening torque for clmp mounting Tighten the screws on the clmp mnully. If you use n utomtic screwdriver, then set suitble mximum tightening torque. You cn find detils for this in the mnufcturer s documenttion for the substructure Clmp mounting for modules with Solrif frmes Avoid clmp mounting for modules with Solrif frmes. Only mount these modules with the Solrif mounting system. You cn lso contct the leo solr brnch in your country. They will provide you with informtion on mounting systems which re lredy in use on greter scle Screw mounting Modules with stndrd frmes The leo modules hve the following mounting holes: either with dimeter of 9 mm or for gen2: long holes with width of 9 mm nd length of 22.5 mm Modules with Solrif frmes Avoid screw mounting for Solrif modules. Only mount Solrif modules with the Solrif mounting system Tightening torque for screw mounting For M8 stinless steel screws, use mximum torque of 24 Nm. 6 b GID AS014 Fig. 8 Definition of clmp length nd depth for frmed modules : Clmp length, b: Clmp depth. The required minimum length of clmp (prllel to the frme side) is 30 mm. The required minimum depth of clmp (perpendiculr to the frme side) is 3 mm. leo solr recommends clmp depth of 5 mm Insertion mounting Modules with stndrd frmes Observe the mnufcturer s instructions for the mounting system. Use the erthing holes for the potentil equlistion. Although edge-to-edge mounting is possible (see lso Ch : Intervls between modules with stndrd frmes ), leo solr recommends mounting t intervls. 5 The totl length is 22.5 mm. The distnce between the hole centres is 13.5 mm. 6 This pplies to unlubricted screws with stndrd thred nd strength clss of 8.8 (minimum breking lod 29.2 kn). leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN Pge 11/20

12 Modules with Solrif frmes 10.7 Key to symbols Only mount modules with Solrif frmes with the Solrif mounting system Lod levels A lod cn be pressure lod s well s suction lod. Lods from snow nd wind re grouped into three levels, which need to be tken into ccount wherever the module is instlled. Higher lod levels mke the requirements for proper instlltion more stringent. The vlues listed below ssume n pproprite instlltion Permissible lods for modules with stndrd frmes 50mm Lod level Permissible pressure : For screw, clmp or ly-in system on long side. Permissible suction Lod level I 2400 P 2400 P Lod level II 3900 P 3900 P Lod level III 5400 P 5400 P Symbol GID AS034 GID AS035 GID AS036 GID AS037 GID AS038 ΔH Dimensions Explntion Permissible clmping re (crisscrossed, red) Extr clmp required in this re (digonlly-crossed, green) Extr support required in this re (trnsversl lines, blue) Clmping point (middle of the clmp length) Liner support Clernce (height) between the bottom edge of the module frme nd the mounting surfce in millimetres (mm). All dimensions re shown in mm. Note: drwings re not lwys true to scle. The numericl vlues re binding Permissible lods for modules with stndrd frmes 35mm Lod level Permissible pressure Permissible suction Lod level I 1400 P 1400 P Lod level II 2400 P 2400 P Lod level III 5400 P 2400 P Permissible lods for modules with Solrif frmes Lod level Permissible pressure Permissible suction Lod level I 2400 P 2400 P Lod level III 5400 P 2400 P Plese observe the instructions from Schweizer for the mounting of modules with Solrif frme. You cn find the mnul on the website from Ernst Schweizer AG Metllbu or on leo solr s website: Snow Lod For the Lod levels II nd III provide device for dditionl mounting of the lowest pnels. The lowest frme prt need to be reinforced (e.g. hook for snow lod) Pge 12/20 leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN

13 leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN Pge 13/20 7 On lower frme prt ginst sliding show. Bolting horizontl/verticl Clmping Long module side, h/v Clmping Short module side, h./v. Clmping Long nd short module side, h./v. Ly-in system Short side, h./v. Ly-in system Long side, h./v. Lod level I Up to 2400 P (pprox. 240 kg/m²) Option 2: Assymetricl clmping Lod level II Up to 3900 P (pprox. 390 kg/m²) 10.8 Mounting drwings for modules with stndrd frmes, S59 Lod levels I nd II Mounting drwing for modules S18, S19, S59 nd S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S59 nd S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. min. 1 brce7 min. 1 brce7 Bolting horizontl/verticl Clmping Long module side, h/v Clmping Short module side, h./v. Clmping Long nd short module side, h./v. Ly-in system Short side, h./v. Ly-in system Long side, h./v. Lod level III Up to 5400 P (pprox. 540 kg/m²) ΔH < 45 mm Option 2: Assymetricl clmping Δ H > 45 mm 800 Note: mx. permitted suction lod 3900 P! Note: mx. permitted suction lod 3900 P! Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 3.0, 07/2014, en-gb-de (1) Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in sys Option 2: Asymmetricl clmping only for on-roo or free-field in Short module side, h. / v. Short side, Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) only for on-roo or free-field in Bolting Clmping Clmping Ly-in sys Short module side, h. / v. Short side, Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Option 2: Asymmetricl clmping Only for on-ro or free-field in Only for on-ro or free-field in Note: mx. permitted suction lod 3900 P! leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 3.0, 07/2014, en-gb-de (1) Pge 13/19 Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 3.0, 07/2014, en-gb-de (1) 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in sys Option 2: Asymmetricl clmping only for on-roo or free-field in Short module side, h. / v. Short side, Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) only for on-roo or free-field in Bolting Clmping Clmping Ly-in sys Short module side, h. / v. Short side, Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Option 2: Asymmetricl clmping Only for on-ro or free-field in Only for on-ro or free-field in Note: mx. permitted suction lod 3900 P! leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 3.0, 07/2014, en-gb-de (1) Pge 13/ Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Bolting Clmping Clmping Ly-in sy Option 2: Asymmetricl clmping only for on-ro or free-field i Short module side, h. / v. Short side Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) only for on-ro or free-field i Bolting Clmping Clmping Ly-in sy < 45 mm Short module side, h. / v. Short side Long module side, horizontl / verticl horizontl / verticl 30 0 x. permitted lod 3900 P! Option 2: Asymmetricl clmping 0.8 Mounting drwings for modules with stndrd frmes Modules S18, S19, S79 Lod levels I nd II ig.9 Mounting drwing for modules S18, S19, S79 t lod levels I nd II imensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system < 45 mm Long module side, horizontl / verticl horizontl / verticl 30 0 x. permitted lod 3900 P! Option 2: Asymmetricl clmping uction lod 3900 P! 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 3.0, 07/2014, en-gb-de (1) Pge 13/19 Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. 800 nd n be exchnged. L ( U Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! For 560 select: b 300 nd c 800 nd b cn be exchnged. or free-field instlltion or free-field instlltion mx. suction lod 3900 P! or free-field instlltion mx. suction lod 3900 P! or free-field instlltion For < For 330 < < 10.8 Mounting drwings for modules with stndrd frmes Lod levels I nd II Mounting drwing for modules S18, S19, S79 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Mounting drwing for module S18, S19, S79 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Bolting Clmping Clmping Ly-in system Ly-in system Option 2: Asymmetricl clmping Long module side, horizontl / verticl horizontl / verticl For 560 select: b 300 nd c 800 nd n be exchnged. Lod level I Up to 2400 P (pprox. 240 kg/m²) Lod level II Up to 3900 P (pprox. 390 kg/m²) Bolting Clmping Clmping Ly-in system Ly-in system Long module side, horizontl / verticl horizontl / verticl 800 For < For 330 Up to 5400 P (pprox. 540 kg/m²) Lod level III Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! Option 2: Asymmetricl clmping Note: mx. permitted suction lod 3900 P! Mx. suction lod 3900 P! min. 1 brce7 min. 1 brce7

14 Module S25, S75 Lod levels I nd II Bolting horizontl/verticl Clmping Long module side, h/v Clmping Short module side, h./v. Ly-in system Short side, h./v. Ly-in system Long side, h./v. Lod level I (pressure) Up to 2400 P (pprox. 240 kg/m²) Lod level II Lod Lod (pressure) level level I I (pressure, Up (pressure, to 3900 suction) P suction) Up (pprox. to Up 2400 to P kg/m²) (pprox. P (pprox kg/m²) kg/m²) min. 1 brce7 Option1: Option 2: Assymetricl clmping Module S25, S Module S25, S75 Lod levels I nd II Lod levels I nd II Bolting Clmping horizontl Bolting / verticl Long module Clmping side, horizontl / verticl Clmping Clmping Ly-in system Ly-in system Ly-in system Ly-in system Lod Lod level level II II (pressure, (pressure, suction) suction) Up to 3900 P (pprox. 390 kg/m²) min. 1 brce7 Fig.11 Mounting drwing for module S25, S75 t lod levels I nd II Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Short module side, h. / v. only for Short on-roof side, h. / v. Long side, h. / v. Short module side, h. / v. or free-field Short instlltion side, h. / v. Long side, h. / v. only or only for free-field for on-roof on-roof instlltion or free-field instlltion Fig.11 Mounting drwing for module S25, S75 t lod levels I nd II Fig.11 Mounting drwing for module S25, S75 t lod levels I nd II Dimensions Lod in level mm. IIIFor ly-in system, lso refer to Ch. 10.5: Insertion mounting. Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Lod level III Lod level Bolting III Clpming Clmping Ly-in system Ly-in system horizontl / verticl Long module side, h/v Bolting Clmping Clmping Ly-in system Ly-in system Bolting Long module Clmping side, horizontl / verticl Short Clmping module side, h. / v. Ly-in system Ly-in system Lod level III (pressure) Up to 5400 P (pprox. 540 kg/m²) Lod level III Up to 5400 P (pprox. 540 kg/m²) Lod level III Up to 5400 P (pprox. 540 kg/m²) Up to 3900 P (pprox. 390 kg/m²) ΔH 45 mm H H < 45 < 45 mm mm Δ H > 45 mm H H mm mm horizontl / verticl Mounting hole horizontl / verticl Short side, h. / v. Long side, h. / v. horizontl / verticl Option Long 1: module side, Option horizontl Option 2: 2: Assymetricl / verticl Asymmetricl clmping Option 1: Option clmping Option 2: Asymmetricl 2: Asymmetricl clmping clmping min. 1 brce For 300 Option Long 1: module side, select: horizontl b 240 / nd verticl c Option : nd Asymmetricl n be clmping Option exchnged. 2: Asymmetricl clmping For 300 select: b 240 nd c 800. For 300 select: nd n be exchnged. b 240 nd c 800. nd n be exchnged Note: Note: mx. permitted Note: Note: suction mx. mx. lod permitted 3900 P! suction suction lod lod P! P! only or only or free-field for free-field for on-roof on-roof instlltion or Note: free-field or mx. free-field mx. suction instlltion permitted instlltion lod Note: suction Note: 3900 mx. P! mx. lod permitted permitted 3900 P! suction suction lod lod P! P! only or only free-field for for on-roof on-roof instlltion Mx. suction lod 3900 P! or Mx. free-field or free-field suction instlltion lod instlltion 3900 P! Mx. Mx. suction suction lod lod P! P! Mx. Mx. only suction suction for on-roof lod lod P! P! Note: mx. permitted mx. suction lod suction lod 3900 P! 3900 P! Fig.12 Mounting drwing for module min. S25, 1 brce7 S75 t lod level III Fig.12 Mounting drwing for module S25, S75 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. b b c c or only free-field for on-roof instlltion GID AS030f2-en-GB GID AS030f2-en-GB GID AS031f2-en-GB GID AS031f2-en-GB GID AS031f2-en-GB Fig.12 Mounting drwing for module S25, S75 t lod level III Dimensions in mm. For ly-in system, lso refer to Ch. 10.5: Insertion mounting. 7 On lower frme prt ginst sliding show. Pge 14/20 leo solr GmbH Mrius-Eriksen-Strße Prenzlu Germny info@leo-solr.com Quick Reference Mnul Rel. 4.3, 07/2017, EN