MPC COBRA SERIES. Manually Programmable Cylindrical Lock D

Transcription

1 51120-D MPC COBRA SERIES Mnully Progrmmle Cylindricl Lock 575 Birch Street Forestville, CT technicl support: fx: H

2 Introduction / Tools nd Mterils Needed Introduction COBRA INSTALLATION AND PROGRAMMING GUIDE / Tools nd Mterils Needed The MPC Cor is ttery-powered mnully progrmmed ccess control system. Up to 100 individul codes cn e progrmmed right t the keypd. A red nd green LED on the keypd provide visul indiction for progrmming nd ccess events. Mechnicl key override is possile when 7-pin smll-formt interchngele core (not included) is instlled in plce of the cylinder plug, which comes stndrd. Either the plug or the IC core must e instlled for the lock to operte. When the cylinder is removed (using the cylinder control key) the lock will unlock. Mnul key override should only e necessry if the low ttery output indictions hve een ignored. (See lso BATTERY INFORMATION: on pge 10). The design llows for mounting on doors from 1-1/2 to 2 thick. A shim is ville to mount the lock to 1-3/8 door. An exterior gsket (EG option) is ville for ppliction to exterior sides of doors. Tools nd Mterils Needed 1. Philips hed screwdriver set 2. Allen wrench set 3. Loctite AA Btteries (provided) The following will lso e needed only for new instlltions: 5. Full size door templte (provided) 6. Pencil 7. Center Punch 8. Hmmer 9. Chisel 10. Squre 11. Level 12. Msking tpe 13. Drill w/chuck for up to 1 drill its 14. Drill it set /8 Hole sw H Pge

3 Frme nd Door Preprtion for Lock Frme nd Door Preprtion for Lock Frme nd Door Preprtion for Lock H Pge

4 Instlling the Cor Instlling the Cor the Cor 1) Instll the Strike Components into the Door Frme: Insert strike ox () into door frme. Plce strike () over strike ox. Secure in plce with 2 screws. 2) Instll the Cylindricl Ltch: Insert the cylindricl ltch into the edge of the door. NOTE: Sloped side of ltch () should fce door strike. Secure in plce with 2 screws. 3) Chnge Hnding if Necessry: Outside escutcheon is shown in figure. Remove nd retin 5/32 socket cp screw (). Remove lever. Rotte lever () to opposite position. Apply thred lock compound * to screw. Reinstll screw. Repet for inside escutcheon (not shown). * Loctite 242 is recomended H Pge

5 Instlling the Cor 4) Remove the Ltch Gurd From the Retrctor: Remove nd retin the screw tht secures the ltch gurd to the retrctor. Remove nd retin the ltch gurd. 5) Instll the Retrctor: From the inside of the door, slide retrctor () into 2-18 hole. IMPORTANT: Mke sure ltch ts engge with retrctor jws. See Detil A. outside inside 6) Instll the Ltch Gurd: Instll ltch gurd () onto retrctor. Secure ltch gurd with screw. outside inside H Pge

6 Instlling the Cor 7) Instll the Outside Escutcheon: If necessry, pply exterior gsket (EG option) to surfce (). Insert the round end of the spindle* () into the outside escutcheon s hu ssemly (c). Dot on cm (d) must e t the 6 o clock (ottom) position. From outside of door, feed outside escutcheon s ttery wire hrness (e) through hole (f) in door. Slide escutcheon ginst door. c e d f * Refer to the chrt elow to determine the correct spindle to use. * 8) Instll the Inside Bseplte Assemly: Oserve the polrity mrkings inside the ttery holder () nd instll the 4, AA tteries (provided) ccordingly. From inside of door, feed ttery wire hrness () through hole in spcer (c) if needed *. Feed ttery wire hrness through hole in inside seplte ssemly (d). Press seplte (nd spcer, if there is one) ginst door. c d * Spcer required on doors thinner thn 1-1/2. spcer required on doors thinner thn 1-1/2 Order P/N: MPC-SK H Pge

7 Instlling the Cor 9) Secure the Bseplte: Apply Loctite 242 to the three provided seplte screws. Secure the seplte with the three screws. 10) Instll the Inside Spindle: Instll spring () into spindle () *. Insert squre end of spindle into retrctor. * * DOOR THICKNESS: 1-3/8 to 1-3/4 --- USE YELLOW SPINDLE 1-7/8 to USE BLACK SPINDLE 11) Connect the Bttery: Connect the ttery wire hrness. c H Pge

8 Instlling the Cor 12) Instll the Inside Escutcheon Cover: Plce the inside escutcheon () over the inside seplte. Using the spnner screw tool (pictured elow), secure the inside escutcheon cover with the 4 provided spnner screws H Pge

9 Instlling the 6 or 7-Pin IC Core for Mnul Key Override Instlling the 6 or 7-Pin IC Core for Mnul Key Override 1) Instll the 7-Pin Smll-Formt IC Core for Mnul Key Override: Hold lock in horizontl position. Remove tpe () if present. Push in plug () until pin (c) until it flls out. Remove plug. c Insert cylinder control key () into core () nd turn clockwise to retrct locking pin. Push cylinder core into lock NOTE: Resistnce will e noticele. Turn key counterclockwise to engge locking pin. Remove key. Lock is now opertionl. NOTE: 6-PIN IC CORE CYLINDERS REQUIRE THAT THE ADAPTER IS INSTALLED TO MAKE THEM AS LONG AS A 7-PIN CYLINDER. THE ADAPTER IS INCLUDED IN THE SCREW PACK. DO NOT INSTALL THE ADAPTER IN A 7-PIN IC CORE CYLINDER. Opertion: Either the cylinder plug or the IC core must e instlled for the lock to operte. Removl of the core or plug utomticlly unlocks the lock. It is recommended tht n IC core e instlled in cse it ever ecomes necessry to unlock the lock using mechnicl mens H Pge

10 Progrmming Lock Codes Progrmming Lock Codes CODE FUNCTIONS: The MPC Cor is mnully progrmmle to hve up to 100 codes. The codes cn hve different functions s descried elow. Severl types of functions hve fctory defult vlues which re opertionl s soon s the lock is instlled. It is highly recommended tht the Progrmming Code e chnged (this will delete ll fctory defult codes) nd new codes e dded. In ddition, it is recommended tht t lest one Freeze/Lockout Code e dded - in cse the tteries get completely drined. (See Bttery Informtion on elow.) All codes cn e 3-8 digits in length (except the Progrmming code which must e 5-8 digits.) Keep log of ll issued codes. Issue codes exclusively with ll odd or ll even numers - this prctice will mke it esier to spot duplicte codes, since ech keypd utton represents two numers (for exmple, code 246 is identicl to code 135.) FUNCTION FACTORY DEFAULT DESCRIPTION The progrmming code puts the lock into progrmming mode. It will not unlock the lock. When Progrmming code plus * is entered the LEDs lterntely flsh severl times indicting the lock is in progrmming mode. If more thn 30 seconds pss in etween progrmming entries, the lock returns to norml opertionl stte. XXX Norml codes unlock the lock for the relock time dely. While the lock is unlocked the green LED will flsh. The LED will stop flshing nd the lock will relock. xxx Toggle codes unlock the lock indefinitely. When the sme (or nother) toggle code is entered, the lock will immeditely relock. When toggle code is entered, the green LED will flsh once. The LED will stop flshing nd the lock will relock. xxx Freeze/Lockout codes prevent other codes from working. The lock cn e locked or unlocked when one is entered. If it is locked, Pss Thru code will unlock it ut ll other codes will not. Only nother Lockout code will reverse the effect. xxx One Use codes unlock the lock for the relock time dely. They will only work once nd then re deleted from memory. They cn used gin if they re progrmmed (dded) into memory gin. Supervised codes require tht two different supervised codes entered in order to unlock the lock for the relock time dely. xxx Pss Thru codes will unlock the door for the relock time dely even if the door is in the lockout mode. BATTERY INFORMATION: The MPC Cor uses four, stndrd AA tteries. The tteries should provide enough life for pproximtely 80,000 lock/unlock cycles. When the tteries re running out the lock provides two different modes of low ttery indiction: First, when code is entered, the red LED will flsh twelve times efore the lock executes the commnd of the code. This is n indiction tht it is time to replce the tteries. The lock will go for out 500 cycles in this condition. After it reches certin point the lock will go into Low Bttery Lockout mode. A Freeze/Lockout code will need to e entered in order gin ccess. If the tteries re not chnged, the lock will eventully not work nd mnul key override (if instlled) will need to e used. CLEARING MEMORY: Clering memory will delete ll progrmmed codes nd restore fctory defult codes. If the memory ever needs to e ersed follow the steps elow: 1. Remove the inside escutcheon. Remove one of the tteries. 2. Press ny key. 3. Hold down the * key nd reinstll the ttery. Continue holding the * key down. The red LED will flsh few times nd then sty on. 4. Relese the * key. 5. Instll the inside escutcheon. Note: to return the lock to the fctory defult relock time dely, do steps 1-4 twice in row H Pge

11 Progrmming Steps Progrmming Steps Use the steps on this pge to progrm codes into the lock. The * key is used like the <ENTER> key is on computer. After pressing the * key, wit for the red nd green LEDs to stop flshing efore proceeding to the next step. If t ny time the red LED stys on while the green LED flshes n error hs occurred. The flshing messge will repet three times. Count the numer of flshes nd consult the error code chrt elow. FLASHES ERROR CODE DESCRIPTION 2 Code too long Mximum digits 6 12 utton keypd 8 6 utton keypd 3 Memory full, delete some codes 4 Use Chnge Prog. code procedure 5 Prog. Code entries do not mtch, code not chnged 6 Invlid entry, strt over 7 Code for deletion not found 8 Code too short Prog. code 5 digit minimum User Code 3 digit minimum 9 Duplicte code H Pge

12 Confirming the Contents of the Box Confirming the Contents of the Box H Pge