CC-410 KIT SERIES INSTRUCTION SHEET

Size: px

Start display at page:

Download "CC-410 KIT SERIES INSTRUCTION SHEET"

Regina Hunt
6 years ago
Views:

(COMPLETE CC-410-W KIT ILLUSTRTED. CUT-OUTS IN TRCK & FSCI TO EXPOSE COMPONENTS) CC-410 KIT SERIES INSTRUCTION SHEET CROWDERTRCK S CTCH N CLOSE TM SYSTEM PREVENTS BOUNCING ND SLMG OF SLIDING DOORS.

PRTS LIST (FOR STNDRD CC-410 1DR KIT) CC-404 TOP MOUNT TRCK X LENGTH (1) (LENGTH = 2 X DOOR WIDTH, EXMPLE: 36 [914MM] DOOR = 72 [1829MM] TRCK) CC-400 HNGER BODY (2) (C/W WHEELS) CC-410-UH U -HOUSING

SCREWS (4) CTCH N CLOSE IN-TRCK STOPS (2) CC-75 OR CC-1 CTCH N CLOSE CLOSING DEVICE (2) (SEE DETILS IN INSTRUCTION STEPS) CP-400 DJUSTMENT WRENCH (1) INCLUDED GUIDE SYSTEM PRTS LIST (BSED ON KIT CODE

1 (COMPLETE CC-410-W KIT ILLUSTRTED. CUT-OUTS IN TRCK & FSCI TO EXPOSE COMPONENTS) CC-410 KIT SERIES INSTRUCTION SHEET CROWDERTRCK S CTCH N CLOSE TM SYSTEM PREVENTS BOUNCING ND SLMG OF SLIDING DOORS. CN BE INSTLLED ON BOTH OPENING ND CLOSING ENDS OF DOORS S NRROW S 18 WIDE. CYCLE TESTED UP TO 50,000 TIMES UP TO 150LBS DOORS USING THE CC-410 WITH CC-1. PRTS LIST (FOR STNDRD CC-410 1DR KIT) CC-404 TOP MOUNT TRCK X LENGTH (1) (LENGTH = 2 X DOOR WIDTH, EXMPLE: 36 [914MM] DOOR = 72 [1829MM] TRCK) CC-400 HNGER BODY (2) (C/W WHEELS) CC-410-UH U -HOUSING (2) CC-410-CB C -BR (2) CC-410-EC END CP (2) CC-410 SQURE HED BOLT X 1-1/4 (2) CC-410-LN LOCK NUT (2) #10 X 1-1/4 PN HED SCREWS (8) #10 X 1-1/4 FLTHED MCHINE SCREWS (2) #10 X 1-1/2 SELF DRILLING SCREWS (4) CTCH N CLOSE IN-TRCK STOPS (2) CC-75 OR CC-1 CTCH N CLOSE CLOSING DEVICE (2) (SEE DETILS IN INSTRUCTION STEPS) CP-400 DJUSTMENT WRENCH (1) INCLUDED GUIDE SYSTEM PRTS LIST (BSED ON KIT CODE ORDERED) CC-410-W KITS CC-410-B KITS C-914 GUIDE CHNNEL X LENGTH (1) (LENGTH = DOOR WIDTH, EXMPLE: 36 [914MM] DOOR = 36 [914MM] GUIDE CHNNEL) C-913 FLOOR GUIDE (1) C-201 GUIDE CHNNEL X LENGTH (1) (LENGTH = DOOR WIDTH, EXMPLE: 36 [914MM] DOOR = 36 [914MM] GUIDE CHNNEL) C-200 FLOOR #10 X 1-3/4 DOOR GUIDE (1) POCKET FLTHED SCREWS (2) TYPICL IMUM OVERLP IN POCKET: #8 X 3/4 PN HED SCREWS (6) PRODUCT OF K.N. CROWDER MFG. INC K.N. Crowder Mfg. Inc Burloak Drive Burlgton, Ontario, Canada L7L 6B3 K.N. Crowder Inc. 210 Eighth Street South Lewiston, New York TOLL-FREE PHONE: KNC (1562) TOLL-FREE FX: WEBSITE: EMIL: customerservice@kncrowder.com 2014 K.N. CROWDER MFG. INC. ll Rights Reserved. 1 1/8 #8 X 3/4 PN HED SCREWS (4) 1 1/8 DOOR POCK TYPICL IMUM OVERL IN POCKET: [50.8 mm WIDE

4 mm] 5/16 3/8 [7.9 [9.5 mm] mm] 29/3 *** 13/3 [10.3 mm] 1 1/8 3 5/8 [92.2 [92.2 mm] mm] 2 1/4 [57.5 mm] 1 3/8 [34.9 mm] IMUM DOOR THICKNESS 1 [44.

1 mm] 2 [69.9 mm] 2 3/3 [53.4 mm] 3/8 [9.5 mm] HNGER DJUSTMENT RNGE: 3/1 [4.8 mm] MX 9/1 [14.3 mm] 5/1 [7.9 mm] [19.0 mm] 3 [92.2 mm] 2 1/4 [57.5 mm] 1 3/8 [34.

2 mm] IN-TRCK STOP RETRCTED SIDE 1 [44.1 mm] 2 [69.9 mm] SEE RIGHT 2 3/3 [53.4 mm] 3/8 [9.5 mm] HNGER DJUSTMENT RNGE: 3/1 [4.8 mm] MX 9/1 [14.3 mm] 3/8 [9.

2 [OPTIONL CC-440 SNP-ON FSCI ILLUSTRTED S SOLID BLCK PROFILE] CC-410-W KIT DETILS (CC-410 HNGER, CC-404 TRCK, C-914/C-913 GUIDE SYSTEM) EFT IN-TRCK FT CC-X 3 IN-TRCK 1 CTCH'N'CLOSE [76.2 mm] STOP STOP [44.1 mm] 2 [69.9 mm] m] ] [15.6 mm] 31/3 23/32 [24.mm] [18.6 mm] 2 3/3 [53.4 mm] 5/8 mm] 3/8 [9.5 mm] HNGER DJUSTMENT RNGE: 3/1 [4.8 mm] MX 9/1 [14.3 mm] [25.4 mm] 5/16 3/8 [7.9 [9.5 mm] mm] 29/3 *** 13/3 [10.3 mm] 1 1/8 3 5/8 [92.2 [92.2 mm] mm] 2 1/4 [57.5 mm] 1 3/8 [34.9 mm] IMUM DOOR THICKNESS 1 [44.5 mm] DOOR SHOWN ***CHECK FIT WITH GUIDE*** CC-410-B KIT DETILS (CC-410 HNGER, CC-404 TRCK, C-201/C-200 GUIDE SYSTEM) T CC-X CTCH'N'CLOSE 3 [76.2 mm] IN-TRCK STOP 1 [44.1 mm] 2 [69.9 mm] 2 3/3 [53.4 mm] 3/8 [9.5 mm] HNGER DJUSTMENT RNGE: 3/1 [4.8 mm] MX 9/1 [14.3 mm] 5/1 [7.9 mm] [19.0 mm] 3 [92.2 mm] 2 1/4 [57.5 mm] 1 3/8 [34.9 mm] IMUM DOOR THICKNESS [15.6 mm] 23/3 [18.6 mm] 1 [44.5 mm] DOOR SHOWN ELEVTION VIEW OF COMPLETE INSTLLTION CC-X CTCH'N'CLOSE CTIVTED SIDE 3 [76.2 mm] IN-TRCK STOP RETRCTED SIDE 1 [44.1 mm] 2 [69.9 mm] SEE RIGHT 2 3/3 [53.4 mm] 3/8 [9.5 mm] HNGER DJUSTMENT RNGE: 3/1 [4.8 mm] MX 9/1 [14.3 mm] 3/8 [9.5 mm] FIXED DISTNCE 3 19/3 [91.4 mm] TO CENTER OF HNGER BOLT 3 [92.2 mm] 2 1/4 [57.5 mm] 1 3/8 [34.9 mm] IMUM DOOR THICKNESS 31/3 [24.6 mm] CTIVTED SIDE 1 [44.5 mm] PRODUCT OF K.N. CROWDER 29/3MFG. INC. 1 1/8 DOOR SHOWN 2014 K.N. CROWDER MFG. [22.9 INC. ll mm] Rights Reserved. RETRCTED SIDE PGE 2

DIMENSIONS SHOW IN THE DETIL VIEWS ON THE PREVIOUS PGE. STEP #2: NOTE: IF CCESS TO THE ENDS OF THE TRCK IS NOT VILBLE, STEPS #3&4 MUST BE COMPLETED BEFORE STEP #2.

SECURE TRCK TO STRUCTURL SUPPORT/HEDER. NOTE: STRTING LOCTIONS T ECH END OF THE TRCK SHOULD BE 1/2 FROM END ND THEN 19 FROM THE FIRST.

SOLID BCKING IS REQUIRED ND SPCING IS RECOMMENDED TO BE BETWEEN 12-16 ON CENTER. CONSULT STRUCTURL ENGINEER TO ENSURE DEQUTE SUPPORT & FSTENING. 19 [482.

WHEN INSTLLING, THE TRIGGERS MUST BE ORIENTED S SHOWN IN THE ILLUSTRTION BELOW. THE TRIGGER MUST BE CLOSEST TO THE END OF THE TRCK.

THE RUBBER BUMPERS OF ECH STOP SHOULD FCE INWRD (TOWRD THE MIDDLE OF THE TRCK ). LEFT END OF TRCK * * RIGHT END OF TRCK * TRIGGER LOCTIONS BUMPER LOCTIONS 1/ [12.

THRED CC-410-LN LOCK NUT ONTO SQURE HED BOLT FROM REVERSE SIDE WITH COLLR OF CC-410-LN LOCK NUT GINST CC-410-CB C -BR S SHOWN BELOW.

3 3/3 [2.7 mm] SET BCK REQUIRED FOR CC-410-EC END CP (SME ON OPPOSITE END) PIN STEP #1: DETERE DOOR SIZE, HEDER HEIGHT & TRCK POSITION, CLERNCE REQUIRED T THE BOTTOM BSED ON THE KIT CODE ORDERED BY USING THE DIMENSIONS SHOW IN THE DETIL VIEWS ON THE PREVIOUS PGE. STEP #2: NOTE: IF CCESS TO THE ENDS OF THE TRCK IS NOT VILBLE, STEPS #3&4 MUST BE COMPLETED BEFORE STEP #2. CUT CC-404 LUUM TRCK TO SIZE IF REQUIRED (TYPICLLY 2 X THE DOOR WIDTH). LOCTE ND PRE-DRILL S THROUGH THE CENTER OF THE TRCK FOR SECURING TO THE STRUCTURL SUPPORT. SECURE TRCK TO STRUCTURL SUPPORT/HEDER. NOTE: STRTING LOCTIONS T ECH END OF THE TRCK SHOULD BE 1/2 FROM END ND THEN 19 FROM THE FIRST. THIS WILL PREVENT INTERFERENCE WITH THE CTCH N CLOSE INSTLLTION (SEE ILLUSTRTION BELOW). IMUM #10 SCREWS OR 1/4 STRUCTURL BOLTS RECOMMENDED TO SECURE THE TRCK. SOLID BCKING IS REQUIRED ND SPCING IS RECOMMENDED TO BE BETWEEN ON CENTER. CONSULT STRUCTURL ENGINEER TO ENSURE DEQUTE SUPPORT & FSTENING. 19 [482.6 mm] STEP #4: SLIDE THE TWO CC-410 HNGER SSEMBLIES (FIG.2 FROM STEP #3) INTO THE TRCK S SHOWN BELOW. NOTE: THE CC-410 HVE TRIGGERS BUILT INTO THE HNGER. WHEN INSTLLING, THE TRIGGERS MUST BE ORIENTED S SHOWN IN THE ILLUSTRTION BELOW. THE TRIGGER MUST BE CLOSEST TO THE END OF THE TRCK. * INSERT THE CTCH N CLOSE IN-TRCK STOPS T ECH END FTER THE HNGERS HVE BEEN PLCED INTO THE TRCK. NOTE: LEVE THE STOP SCREWS LOOSE TO LLOW THE STOPS TO SLIDE FREELY WITHIN THE TRCK. THE RUBBER BUMPERS OF ECH STOP SHOULD FCE INWRD (TOWRD THE MIDDLE OF THE TRCK ). LEFT END OF TRCK * * RIGHT END OF TRCK * TRIGGER LOCTIONS BUMPER LOCTIONS 1/ [12.7 mm] STEP #3: SSEMBLE THE CC-410 CTCH N CLOSE HNGERS S SHOWN BELOW: FIG. 1 - LOCTE CC-410 SQURE HED BOLT X 1-1/4 INTO THE ON THE CC-410-CB C -BR FROM THE UNDERSIDE S SHOWN BELOW. THRED CC-410-LN LOCK NUT ONTO SQURE HED BOLT FROM REVERSE SIDE WITH COLLR OF CC-410-LN LOCK NUT GINST CC-410-CB C -BR S SHOWN BELOW. THEN THRED THIS COMPLETE SSEMBLY INTO THE CC-400 HNGER BODY FROM THE UNDERSIDE (SIDE OPPOSITE THE TRIGGER). FIG. 2 - COMPLETE CC-410 HNGER SSEMBLY (2 X REQUIRED) FIG. 3 - SHOWS THE UNDERSIDE OF COMPLETE SSEMBLY WITH CC-410 SQURE HED BOLT LOCKED INTO PLCE BETWEEN THE INSIDE FLNGES OF THE CC-410-CB C -BR. FIG. 1 TRIGGER ILLUSTRTION (TO THE RIGHT) SHOWS THE CORRECT POSITIONING OF THE STOPS IN THE TRCK. SEE FIGURE BOVE FOR PROPER INSTLLTION.!!!WRNING!!! IF HNGER BODIES ND STOPS RE NOT INSTLLED S SHOWN BOVE, SYSTEM WILL NOT FUNCTION PROPERLY. STEP #5: PREPRE DOOR TO RECEIVE CC-410-UH U -HOUSING FLUSH WITH THE TOP EDGE OF THE DOOR. SLOTS MUST BE 6 LONG, 7/8 WIDE ND 5/8 DEEP. SEE ILLUSTRTION BELOW FOR MORE DETILS. FIG. 2 FIG. 3 WIDE HIGH SEE LEFT FOR DIMENSIONS LONG PRODUCT OF K.N. CROWDER MFG. INC K.N. CROWDER MFG. INC. ll Rights Reserved. PGE 3

STEP #6: PREPRE BOTTOM OF DOOR BSED ON KIT ORDERED. SEE BELOW FOR DIFFERENT GUIDE OPTIONS CCORDINGLY.

IF GUIDE CHNNEL WILL BE INSTLLED SHORT FROM THE EDGES, IT IS RECOMMENDED TO HVE T LEST 1/2 [12.7 mm] DOOR MTERIL T ECH END OF THE DOOR BEFORE THE STRT OF THE GUIDE CHNNEL SLOT. [15.

3 mm] WIDE ***CHECK FIT WITH GUIDE*** STEP #6 OPTION : FOR CC-410-W KITS ONLY PREPRE C-914 GUIDE CHNNEL SLOT T LEST 1 WIDE IN CENTER OF DOOR, ND T LEST 29/32 [23 mm] DEEP.

SEE BELOW: WIDE TYPICL IMUM OVERLP IN POCKET: HIGH TYPICL IMUM OVERLP IN POCKET: 29/3 HIGH TYPICL IMUM OVERLP OF DOOR ON WLL: STEP #6 OPTION B: FOR CC-410-B KITS PREPRE C-201 GUIDE CHNNEL SLOT T LEST

3 mm] WIDE ***CHECK FIT WITH GUIDE*** LONG STEP #7: WLL WHERE DOOR OPENS TO PLCE CC-410-UH U -HOUSING INTO SLOT CRETED IN STEP #5 WITH PIN TOWRDS THE CENTER OF THE DOOR.

4 STEP #6: PREPRE BOTTOM OF DOOR BSED ON KIT ORDERED. SEE BELOW FOR DIFFERENT GUIDE OPTIONS CCORDINGLY. ESTHETIC NOTE: IF SUFFICIENT OVERLP OF THE DOOR IS PROVIDED, GUIDE CHNNEL HIGH CN BE INTO THE DOOR WITHOUT CUTTING SLOT THE FULL LENGTH OF THE DOOR. IF GUIDE CHNNEL WILL BE INSTLLED SHORT FROM THE EDGES, IT IS RECOMMENDED TO HVE T LEST 1/2 [12.7 mm] DOOR MTERIL T ECH END OF THE DOOR BEFORE THE STRT OF THE GUIDE CHNNEL SLOT. [15.9 SUGGESTED mm] IMUM PENED POSITIONWIDE 1/ [12.7 mm] IN SET DOOR BCK REQUIRED FOR THIS OPTION WLL 1 WHERE 1/8 DOOR OPENS TO LOSED POSITION 13/3 [10.3 mm] WIDE ***CHECK FIT WITH GUIDE*** STEP #6 OPTION : FOR CC-410-W KITS ONLY PREPRE C-914 GUIDE CHNNEL SLOT T LEST 1 WIDE IN CENTER OF DOOR, ND T LEST 29/32 [23 mm] DEEP. IT IS RECOMMENDED TO MKE THE 2 SLOT S CCURTE S POSSIBLE FOR SECURE FIT ND NET PPERNCE. SEE BELOW: WIDE TYPICL IMUM OVERLP IN POCKET: HIGH TYPICL IMUM OVERLP IN POCKET: 29/3 HIGH TYPICL IMUM OVERLP OF DOOR ON WLL: STEP #6 OPTION B: FOR CC-410-B KITS PREPRE C-201 GUIDE CHNNEL SLOT T LEST 5/8 [15.9 mm] WIDE IN CENTER OF DOOR, ND T LEST 3/4 DEEP. IT IS RECOMMENDED TO MKE THE SLOT S CCURTE S POSSIBLE FOR SECURE FIT ND NET PPERNCE. SEE BELOW: WIDE HIGH 13/3 [10.3 mm] WIDE ***CHECK FIT WITH GUIDE*** LONG STEP #7: WLL WHERE DOOR OPENS TO PLCE CC-410-UH U -HOUSING INTO SLOT CRETED IN STEP #5 WITH PIN TOWRDS THE CENTER OF THE DOOR. HOUSING MUST BE SET 3/32 FROM THE EDGE OF DOOR TYPICL IN ORDER IMUM TO CCOMMODTE OVERLP CC-410-EC OF END CP (SEE ILLUSTRTION DOOR BELOW ON FOR WLL: DETILS). SECURE TO DOOR WITH #10 X 1-1/4 PN HED SCREWS (4) REPET FOR OPPOSITE END OF DOOR. 3/3 [2.7 mm] SET BCK REQUIRED FOR PIN CC-410-EC END CP (SME ON OPPOSITE END) WIDE IN OPENED DOOR POSITION STEP #8: 29/3 INSTLL [22.9 GUIDE mm] CHNNEL S PER OPTIONS BELOW BSED ON KIT ORDERED. TYPICL HIGH IMUM OVERLP IN POCKET: STEP IN #8 2 CLOSED DOOR OPTION [50.8 POSITION : mm] FOR CC-410-W KITS ONLY CUT C-914 LUUM GUIDE CHNNEL TO CORRECT LENGTH S REQUIRED. DRILL S IN C-914 GUIDE CHNNEL ND PRE-DRILL S. LOCTE CHNNEL IN SLOT PREVIOUSLY PREPRED BOVE ND SCREW CHNNEL INTO PLCE WITH #8 X 3/4 PN HED SCREWS (4 SCREWS RE PROVIDED IN KIT). 29/3 HIGH WLL WHERE DOOR OPENS TO WIDE TYPICL IMUM OVERLP OF DOOR ON WLL: OPENED P 1 i [25.4 DOOR O WIDE REC IN DO CLOSED P HIGH STEP #8 OPTION B: FOR CC-410-B KITS ONLY CUT C-201 LUUM GUIDE CHNNEL TO CORRECT LENGTH S REQUIRED. DRILL S IN C-201 GUIDE CHNNEL ND PRE-DRILL S. WIDE LOCTE CHNNEL IN SLOT PREVIOUSLY PREPRED BOVE ND SCREW CHNNEL INTO PLCE WITH #8 X 3/4 PN HED SCREWS (4 SCREWS RE PROVIDED IN KIT). 29/3 [22.9 HIGH REC IN DO HIGH WLL WHERE DOOR OPENS TO PRODUCT OF K.N. CROWDER MFG. INC. SUGGESTED IMUM TYPICL IMUM OVERLP OF 2014 K.N. CROWDER MFG. INC. ll Rights Reserved. 1/ [12.7 mm] DOOR ON WLL: SET BCK REQUIRED PGE 4

STEP #9: LOCTE GUIDES S REQUIRED ND SECURE S PER THE DIFFERENT OPTIONS BELOW BSED ON KIT

DIMENSIONS FOR GUIDES CN BE FOUND ON THE FIRST PGE IN THE PRTS LIST SECTION BSED ON KIT

PPLICTIONS ILLUSTRTED BELOW: STEP #11: ONCE DJUSTMENTS HVE BEEN FINLIZED, SECURE CC-410-LN

TYPICL IMUM OVERLP IN POCKET: STEP #12: WLL WHERE DOOR OPENS TO INSTLL CC-410-EC END CPS (2)

DOOR ON WLL: T NS TO SED NS OF ] STEP #9 OPTION : FOR CC-410-W KITS ONLY LOCTE C-913 5/8

9 REQUIREMENT CLOSED mm] BSED POSITION CLOSED WIDE POSITION ON THE BOVE SUGGESTIONS ND SITE

STEP #9 OPTION B: FOR CC-410-B KITS ONLY LOCTE C-200 GUIDE S PER REQUIREMENT BSED WIDE ON

HIGH 29/3 HIGH STEP #10: RISE THE DOOR ND POSITION OVER THE GUIDE.

LOOSEN THE BOLT TO THE DJUSTMENT SLOT FOUND ON THE C -BR, DJUST ND THEN SECURE CCORDINGLY.

STEP #13: FTER THE DOOR HS BEEN INSTLLED, POSITION DOOR PPROXIMTELY 5-10 WY FROM THE FINL

PUSH THE LOOSE LEFT SIDE STOP (INSTLLED IN STEP #4) GINST THE HNGER BODY S SHOWN BELOW: BCK

END CP MUST ENGGE WITH CC-410-UH HERE STEP #14: WITH THE STOP LOOSE, SLIDE THE DOOR TO THE

WHERE DOOR OPENS TO WLL WHERE DOOR OPENS TO TYPICL IMUM OVERLP OF TYPICL IMUM OVERLP OF DOOR

5 STEP #9: LOCTE GUIDES S REQUIRED ND SECURE S PER THE DIFFERENT OPTIONS BELOW BSED ON KIT ORDERED. DIMENSIONS FOR GUIDES CN BE FOUND ON THE FIRST PGE IN THE PRTS LIST SECTION BSED ON KIT ORDERED. TYPICL INSTLLTION LOCTION FOR FLOOR GUIDES: GUIDE CHNNEL WITH GUIDE ON FLOOR FOR POCKET DOOR PPLICTIONS ILLUSTRTED BELOW: STEP #11: ONCE DJUSTMENTS HVE BEEN FINLIZED, SECURE CC-410-LN LOCK NUT WITH CP-400 DJUSTMENT WRENCH. TYPICL IMUM OVERLP IN POCKET: STEP #12: WLL WHERE DOOR OPENS TO INSTLL CC-410-EC END CPS (2) ND SECURE WITH #10 X 1-1/4 FLTHED MCHINE SCREWS (2) S SHOWN BELOW: TYPICL IMUM OVERLP OF DOOR ON WLL: T NS TO SED NS OF ] STEP #9 OPTION : FOR CC-410-W KITS ONLY LOCTE C-913 5/8 GUIDE S PER [15.9 REQUIREMENT CLOSED mm] BSED POSITION CLOSED WIDE POSITION ON THE BOVE SUGGESTIONS ND SITE CONDITIONS ND SECURE TO FLOOR WITH #10 X 1-3/4 FLTHED SCREWS (2). STEP #9 OPTION B: FOR CC-410-B KITS ONLY LOCTE C-200 GUIDE S PER REQUIREMENT BSED WIDE ON THE BOVE SUGGESTIONS ND SITE CONDITIONS ND SECURE TO FLOOR WITH #8 X 3/4 PN HED SCREWS (2). HIGH 29/3 HIGH STEP #10: RISE THE DOOR ND POSITION OVER THE GUIDE. SLIDE THE CC-410-CB C -BR INTO THE CC-410-UH U -HOUSINGS PREVIOUSLY INSTLLED ON THE DOORS. NOTE: THREDED END MUST FCE OUTWRD. IN ORDER TO MKE HEIGHT DJUSTMENTS, THE DOOR WILL NEED TO COME OFF THE HNGERS IN THE TRCK, LOOSEN THE BOLT TO THE DJUSTMENT SLOT FOUND ON THE C -BR, DJUST ND THEN SECURE CCORDINGLY. REPET STEP FOR OPPOSITE END OF DOOR. STEP #13: FTER THE DOOR HS BEEN INSTLLED, POSITION DOOR PPROXIMTELY 5-10 WY FROM THE FINL POSITION T ONE END (USING THE LEFT SIDE S N EXMPLE TO SHOW THIS STEP). PUSH THE LOOSE LEFT SIDE STOP (INSTLLED IN STEP #4) GINST THE HNGER BODY S SHOWN BELOW: BCK OF END CP MUST ENGGE WITH CC-410-UH HERE BCK OF END CP MUST ENGGE WITH CC-410-UH HERE BCK OF END CP MUST ENGGE WITH CC-410-UH HERE STEP #14: WITH THE STOP LOOSE, SLIDE THE DOOR TO THE LEFT TO THE FINL/DESIRED POSITION OF THE DOOR S SHOWN BELOW: WLL WHERE DOOR OPENS TO WLL WHERE DOOR OPENS TO WLL WHERE DOOR OPENS TO TYPICL IMUM OVERLP OF TYPICL IMUM OVERLP OF DOOR ON WLL: DOOR ON WLL: TYPICL IMUM OVERLP OF DOOR ON WLL: STEP #15: ONCE THE FINL POSITION IS CHIEVED, SLIDE THE DOOR WY FROM THE STOP. LOCK THE STOP IN POSITION BY TIGHTENING THE TWO CP SCREWS ON THE STOP WITH 3/16 LLEN KEY ( IS SECURED BY FRICTION FIT). HNGER DJUSTMENT VIEW PRODUCT OF K.N. CROWDER MFG. INC K.N. CROWDER MFG. INC. ll Rights Reserved. STEP #16: REPET STEPS #13 THRU #15 FOR OPPOSITE SIDE. NOTE: RE-CHECK FINL DOOR POSITIONS GINST THE SECURED STOPS BEFORE PROCEEDING TO STEP #17. RE-DJUST IF REQUIRED. PGE 5

STEP #17: BEFORE INSTLLING THE CTCH N CLOSE DEVICE, PLESE ENSURE IT IS IN THE RETRCTED POSITION. IF IT IS NOT IN THIS POSITION, SLIDE IT DOWN UNTIL IT LOCKS INTO THIS POSITION S SHOWN BELOW.

ID END # RETRCTED POSITION IMPORTNT CTCH N CLOSE CLOSING DEVICE NOTES: IF THE DOORS RE 75LBS OR LESS, PLESE ENSURE THE CC-75 CTCH N CLOSE CLOSING DEVICE IS BEING USED.

IF THE INCORRECT CTCH N CLOSE CLOSING DEVICE IS USED, THERE IS HIGHER RISK OF FILURE, NOT PROVIDING ENOUGH STRENGTH ND/OR TOO MUCH RESISTNCE IS EXPERIENCED WHEN OPERTING THE DOOR. 1/ [12.

6 mm] STEP #18: PLCE THE CTCH N CLOSE CLOSING DEVICE INTO THE TRCK WITH THE SOLID END (ID END # SHOWN ON PREVIOUS PGE) RESTING GINST THE UPPER BODY ON THE STOPS (BOVE THE BUMPER) INSTLLED PREVIOUSLY.

SEE ILLUSTRTION BELOW: ID END # DETIL SNP-ON POINT (SME FOR BOTTOM) END VIEW STEP #19: SECURE CTCH N CLOSE CLOSING DEVICE TO TRCK WITH #10 X 1-1/2 SELF DRILLING SCREWS.

NOTE: DO NOT USE IMPCT DRIVER TO SECURE CTCH N CLOSE CLOSING DEVICES TO THE TRCK. DO NOT OVERTIGHTEN SCREWS. TO ESE INSTLLTION, IT IS RECOMMENDED TO PRE-DRILL TRCK WITH 5/32 DRILL BIT.

6 STEP #17: BEFORE INSTLLING THE CTCH N CLOSE DEVICE, PLESE ENSURE IT IS IN THE RETRCTED POSITION. IF IT IS NOT IN THIS POSITION, SLIDE IT DOWN UNTIL IT LOCKS INTO THIS POSITION S SHOWN BELOW. NOTE: THIS WILL REQUIRE SIGNIFICNT FINGER PRESSURE. ID END # RETRCTED POSITION IMPORTNT CTCH N CLOSE CLOSING DEVICE NOTES: IF THE DOORS RE 75LBS OR LESS, PLESE ENSURE THE CC-75 CTCH N CLOSE CLOSING DEVICE IS BEING USED. IF THE DOORS RE IMUM 75LBS UP TO 150LBS, PLESE ENSURE THE CC-1 CTCH N CLOSE CLOSING DEVICE IS BEING USED. IF THE INCORRECT CTCH N CLOSE CLOSING DEVICE IS USED, THERE IS HIGHER RISK OF FILURE, NOT PROVIDING ENOUGH STRENGTH ND/OR TOO MUCH RESISTNCE IS EXPERIENCED WHEN OPERTING THE DOOR. 1/ [12.7 mm] 19 [482.6 mm] STEP #18: PLCE THE CTCH N CLOSE CLOSING DEVICE INTO THE TRCK WITH THE SOLID END (ID END # SHOWN ON PREVIOUS PGE) RESTING GINST THE UPPER BODY ON THE STOPS (BOVE THE BUMPER) INSTLLED PREVIOUSLY. WHEN THE CTCH N CLOSE CLOSING DEVICE IS RESTING TIGHT GINST THE UPPER BODY OF THE STOP, IT IS IN THE CORRECT POSITION ND WILL CLOSE THE DOOR TO THE DESIRED POSITION. SEE ILLUSTRTION BELOW: ID END # DETIL SNP-ON POINT (SME FOR BOTTOM) END VIEW STEP #19: SECURE CTCH N CLOSE CLOSING DEVICE TO TRCK WITH #10 X 1-1/2 SELF DRILLING SCREWS. DO THE SME FOR THE OPPOSITE END WITH THE CTCH N CLOSE CLOSING DEVICE INSTLLED IN REVERSE S SHOWN ON THE FRONT PGE IN THE ELEVTION VIEW OF COMPLETE INSTLLTION ILLUSTRTION. NOTE: DO NOT USE IMPCT DRIVER TO SECURE CTCH N CLOSE CLOSING DEVICES TO THE TRCK. DO NOT OVERTIGHTEN SCREWS. TO ESE INSTLLTION, IT IS RECOMMENDED TO PRE-DRILL TRCK WITH 5/32 DRILL BIT. IT IS RECOMMENDED TO SECURE THE FIRST SCREW (CLOSEST TO THE END VIEW STOP), TEST SYSTEM BY SLIDING THE DOOR TO CTIVTE THE CTCH N CLOSE. IF IT IS IN THE CORRECT POSITION, SECURE WITH SECOND SCREW. REMOVE NY DRILL FILLINGS FROM INSIDE THE TRCK S THIS WILL FFECT THE OPERTION OF THE SLIDING DOOR SYSTEM. STEP #20: DETIL SNP-ON POINT TEST THE COMPLETE CTCH N CLOSE SYSTEM BY (SME SLIDING FOR BOTTOM) THE DOOR TO BOTH LEFT ND RIGHT TO CTIVTE THE CLOSING DEVICES. OPTIONL CC-440 FSCI INSTLLTION DETIL DETIL SNP-ON POINT (SME FOR BOTTOM) STEP #1: CUT CC-440 FSCI TO CORRECT LENGTH IF REQUIRED. TYPICLLY FSCI IS SME LENGTH S TRCK PREVIOUSLY INSTLLED. STEP #2: LIFT FSCI UP TO TRCK ND SNP-ON S SHOWN BELOW. REPET FOR OPPOSITE SIDE IF NECESSRY. DETIL DETIL SNP-ON POINT (SME FOR BOTTOM) DETIL DETIL SNP-ON POINT DETIL SNP-ON POINT SIDE VIEW (TRCK SHOWN WITH CUTOUT) OPTIONL CC-441 END CP INSTLLTION ID END # DETIL RETRCTED POSITION DETIL SNP-ON POINT INSTLL CC-441 END CP S SHOWN TO THE BELOW WITH THE SUPPLIED #6 SCREWS (2 SCREWS PER END CP PROVIDED). NOTE: DO NOT INSTLL WITH IMPCT DRIVER TROUBLESHOOTING: ISSUE: IF THE DOOR IS NOT ENGGING THE CLOSING DEVICE. SOLUTION: ) ENSURE HNGERS RE CORRECTLY ORIENTED. SEE STEP #4. B) ENSURE THE CTCH N CLOSE IS IN THE RETRCTED POSITION PRIOR TO SLIDING DETIL THE DOOR CLOSED/OPEN. SEE STEP #17. SNP-ON POINT ISSUE: CHTTER/NOISE WHEN DOOR IS SLIDING. SOLUTION: ENSURE THERE RE NO LUUM SHVINGS WITHIN THE TRCK. SHVINGS CN BECOME EMBEDDED IN NYLON TIRES ND CUSE NOISY OPERTION. ISSUE: REPLCING THE CTCH N CLOSE DEVICE. SOLUTION: THE CTCH N CLOSE TRCK ND HRDWRE SYSTEM HS BEEN DESIGNED FOR ESY INSTLLTION. SIMPLY REMOVE THE TWO SCREWS THT HOLD THE CTCH N CLOSE IN PLCE ND REPLCE THE DEVICE WITH NEW ONE IF FILURE OCCURS. OPTIONL PRODUCTS: PRODUCT OF K.N. CROWDER MFG. INC K.N. CROWDER MFG. INC. ll Rights Reserved. PLESE VISIT OUR WEBSITE FOR OTHER OPTIONL PRODUCT SUCH S SIDE MOUNT GUIDES, DOOR LOCKS & PULLS ND MORE. PGE 6

CCD-493 KIT SERIES INSTRUCTION SHEET

(COMPLETE CCD-493-W KIT ILLUSTRTED. CUT-OUTS IN TRCK TO EXPOSE COMPONENTS) CCD-493 KIT SERIES INSTRUCTION SHEET CROWDERTRCK S CTCH N CLOSE TM SYSTEM PREVENTS BOUNCING ND SLMMING OF SLIDING S. CN BE INSTLLED