KING COBRA/KING COBRA-2 NARROW STILE SERIES KC9357/KC9357-2

Size: px

Start display at page:

Download "KING COBRA/KING COBRA-2 NARROW STILE SERIES KC9357/KC9357-2"

Piers Watkins
6 years ago
Views:

1 KING COBRA/KING COBRA-2 NARROW STILE SERIES KC9357/KC Keypd Progrmmble nd SNAP Comptible Trim For Rim Exit Devices Mounted On Aluminum Doors B

2 Contents of the Box KC9357/KC INSTALLATION INSTRUCTIONS Contents of of the Box B Pge

3 Introduction / Tools nd Mterils Needed / Contct Info Introduction: / Tools nd Mterils Needed / Contct Info The KC9357/KC is designed to replce existing exterior cylinders or trim on Adms Rite 8800 rim exit devices mounted on luminum doors. The trim will llow ccess by ctivting the exit device str ltch when n ccess code or ibutton is entered nd the turnpiece is turned clockwise. Mechnicl key override is stndrd. The trim is comptible with the dogging fetures vilble with the Adms Rite exit devices. The KC9357/KC is comptible with Adms Rite 8800 rim exit devices on luminum doors. Tools nd Mterils Needed: 1. Flt hed screwdriver w/stright, 1/8 wide blde 2. Smll Philips hed screwdriver 3. 1/16 Allen wrench 4. Long nose needle-nose pliers 5. Center punch 6. Hmmer 7. Power drill 8. 19/32 drill bit 9. 1/4 drill bit 10. Jig sw w/blde 11. Drill & Tp for threds Contct Informtion: Schlge Lock Compny 575 Birch Street Forestville, CT technicl support: fx: web: B Pge

4 Door Preprtion Door Preprtion Door Conditions: Instlltion my require the use of cover plte () to cover the holes left in the door. If n existing pull (b) must be removed, Ives offers comptible pull. >Schlge Cover Plte P/N: KC9000-KRP >Ives Pull P/N: xxx (xxx = finish) b Bckset is determined by the Adms Rite lock. (6.656 ) Horizontl centerline for Adms Rite 8800 Rim (3.957 ) For fctory prepped doors, use dimensions shown. Dimensions re referenced from center of 1-1/4 cylinder hole. Bckset is determined by the Adms Rite lock. When instlling new Adms Rite locks, do not instll outside cylinder (becuse this trim replces it). (2.693 ) B Pge

Cms, Cores, Cylinders nd Blocking Rings Cms, Cores, Cylinders nd Blocking Rings Cms For Mechnicl Override Cylinder: The KC9000 trim requires the use

> Cm for Stndrd Mortise cylinder: Schlge Everest: L583-153 Schlge Clssic: L583-254 > Cm for Interchngeble Core: Schlge IC Cm: L583-255 IC Cores: >

core w/ cm: Schlge: 30-016-<FINISH> NOTE: This core requires the use of 3/8 blocking ring: Schlge: 36-079-037-<FINISH> Cylinders / Blocking Rings: The

The blocking ring thickness is equl to the cylinder length, minus 1-1/8. For exmple, if you use 1-1/2 cylinder you need 3/8 blocking ring.

5 Cms, Cores, Cylinders nd Blocking Rings Cms, Cores, Cylinders nd Blocking Rings Cms For Mechnicl Override Cylinder: The KC9000 trim requires the use of clover lef cm (). This is list of comptible Schlge prts. For other mnufcturers, consult cross-reference chrts. > Cm for Stndrd Mortise cylinder: Schlge Everest: L Schlge Clssic: L > Cm for Interchngeble Core: Schlge IC Cm: L IC Cores: > Smll Formt IC core w/ cm: Schlge: <FINISH> NOTE: This core requires the use of 1/4 blocking ring: Schlge: <FINISH> > Full Size IC core w/ cm: Schlge: <FINISH> NOTE: This core requires the use of 3/8 blocking ring: Schlge: <FINISH> Cylinders / Blocking Rings: The KC9000 cn use 1-1/8 mortise cylinder without the use of blocking ring. For cylinders longer thn 1-1/8 blocking ring is required. The blocking ring thickness is equl to the cylinder length, minus 1-1/8. For exmple, if you use 1-1/2 cylinder you need 3/8 blocking ring. Compression rings cn be ordered from Schlge distributor: Thickness: Schlge Prt Number: No compression ring: 1/ <FINISH> 1/ <FINISH> 3/ <FINISH> 1/ <FINISH> B Pge

Instlling the KC9357/KC9357-2 Instlling the KC9357/KC9357-2 the KC9357/KC9357-2 If your trim hs key cylinder lredy instlled, skip to Determine Hnd: on pge 12.

6 Instlling the KC9357/KC Instlling the KC9357/KC the KC9357/KC If your trim hs key cylinder lredy instlled, skip to Determine Hnd: on pge 12. Otherwise, continue with Loosen the Bseplte Screws: on this pge. 1) Loosen the Bseplte Screws: IMPORTANT: Do not remove ny of the screws in the following step or it will be difficult to reinstll them. Using smll Philips hed screwdriver, loosen screws & b in bseplte, round key cylinder hole, one turn. NOTE: Screws, b, c & d re set t the fctory. Screws & b re tightened nd screws c & d re left loose. c d b 2) A Key Cylinder Tht Is At Lest 1-1/8 Long Must Be Instlled: > The key cylinder tht you instll must be 1-1/8 long or longer. >>>> Do not ttempt to instll key cylinder tht is shorter thn 1-1/8 > The two photos below illustrte the difference between 1 nd 1-1/8 key cylinder. 1 long key cylinder. DO NOT ATTEMPT TO INSTALL A 1 LONG KEY CYLINDER. 1-1/8 long key cylinder ONLY INSTALL A KEY CYLIN- DER THAT IS AT LEAST 1-1/ B Pge

Instlling the KC9357/KC9357-2 3) Mke Room for Key Cylinder: Due to the dimeter of the key cylinder, it is necessry to hve ded ltch () plced out

.. Using your finger or pir of needle-nose pliers, push ded ltch towrds the top end of trim s indicted by rrow in photo.

4) Hold Ded Ltch in Plce: To insure tht ded ltch is plced fr enough out of the wy to llow key cylinder to be threded in properly: Insert finger

7 Instlling the KC9357/KC ) Mke Room for Key Cylinder: Due to the dimeter of the key cylinder, it is necessry to hve ded ltch () plced out of the wy when instlling the key cylinder. Therefore... Using your finger or pir of needle-nose pliers, push ded ltch towrds the top end of trim s indicted by rrow in photo. NOTE: As indicted by rrow in photo, you ll notice tht when you push the ded ltch forwrd, it will swing little bit in counterclockwise direction. 4) Hold Ded Ltch in Plce: To insure tht ded ltch is plced fr enough out of the wy to llow key cylinder to be threded in properly: Insert finger into key cylinder hole nd hold ded ltch firmly in plce. Crefully turn the trim over while keeping the ded ltch in position. 5) Verify Plcement of Ded Ltch: Fig. 1 Two holes on ded ltch () should be showing within the two holes (b) in bseplte. b B Pge

Instlling the KC9357/KC9357-2 6) Instll the Key Cylinder: Instll.050 cylinder wsher. IMPORTANT: A.050 cylinder wsher must be used IN ALL CASES, regrdless of the key cylinder length.

A simple formul for determining blocking ring thickness is: Blocking ring thickness = length of cylinder minus 1-1/8 If not lredy done, instll cm onto cylinder.

8 Instlling the KC9357/KC ) Instll the Key Cylinder: Instll.050 cylinder wsher. IMPORTANT: A.050 cylinder wsher must be used IN ALL CASES, regrdless of the key cylinder length. If you re instlling cylinder tht is longer thn 1-1/8, you must lso instll blocking ring (see Tble 1: Blocking Rings, on pge 8). A simple formul for determining blocking ring thickness is: Blocking ring thickness = length of cylinder minus 1-1/8 If not lredy done, instll cm onto cylinder. Cm must be clover lef design (see Tble 2: Recommended Cms, on pge 8). Tilt top of trim down t shrp ngle. Screw in key cylinder until it stops. Use mechnicl key s hndle for turning if necessry. Tble 1: Blocking Rings Key Cylinder Length Blocking Ring (Schlge P/N; XXX = finish) 1-1/4 1/8 ( XXX) 1-3/8 1/4 ( XXX) 1-1/2 3/8 ( XXX) 1-5/8 1/2 ( XXX) Tble 2: Recommended Cms Cylinder/Core Schlge Type Prt Number Stndrd Mortise Cyl Everest L Stndrd Mortise Cyl Clssic L Interchngeble Core IC Cm L ) Align Key Cylinder: After screwing it ll the wy in, bck off on key cylinder (no more thn one turn) until key is t the bottom. If key cylinder hs logo (), logo should be t the top of key cylinder B Pge

Instlling the KC9357/KC9357-2 8) Alignment of Interchngeble Cores: If n IC Core is used, center the interfce towrd the bottom.

> Fully tighten c nd d. > Check ll four screws to mke sure tht ll four re completely tight.

9 Instlling the KC9357/KC ) Alignment of Interchngeble Cores: If n IC Core is used, center the interfce towrd the bottom. 9) Tighten the Four Screws in the Bseplte: Tighten the four bseplte screws in the following order: > Tighten nd b until snug. > Tighten c nd d until snug. > Fully tighten nd b. > Fully tighten c nd d. > Check ll four screws to mke sure tht ll four re completely tight. c d b 10) The Ded Ltch s Criticl Edge: For clrity purposes only, photo on the right is view of dedltch with escutcheon removed. Edge () is referred to s the ded ltch s criticl edge. IMPORTANT: In the next step, the criticl edge on dedltch will hve to be lined up with hole (b) in bseplte. See Position the Ded Ltch s Set Screw Hole: on pge 10 b B Pge

Instlling the KC9357/KC9357-2 11) Position the Ded Ltch s Set

with the lrger hole in the bseplte s shown in photo on right.

this. IMPORTANT: When the ded ltch s criticl edge is correctly

10 Instlling the KC9357/KC ) Position the Ded Ltch s Set Screw Hole: Tilt the trim until you see the criticl edge lign with the lrger hole in the bseplte s shown in photo on right. Look closely t edge of ded ltch s criticl edge () when doing this. IMPORTANT: When the ded ltch s criticl edge is correctly ligned, the ded ltch s set screw hole will likewise be correctly ligned. Photos A, B nd C below illustrte exmples of n incorrectly ligned criticl edge. Photo D is n exmple of correctly ligned criticl edge. A B C NOT CORRECTLY ALIGNED NOT CORRECTLY ALIGNED NOT CORRECTLY ALIGNED D CORRECTLY ALIGNED B Pge

Instlling the KC9357/KC9357-2 12) Prtilly Tighten the Set Screw: Using 1/16 Allen wrench, prtilly turn in the set screw until outer end of set screw is bout flush with surfce of bseplte.

IMPORTANT: At this time, outer end of set screw should be little bit below the surfce of the bseplte, s shown in photo A.

Position the Ded Ltch s Set Screw Hole: on pge 10).

11 Instlling the KC9357/KC ) Prtilly Tighten the Set Screw: Using 1/16 Allen wrench, prtilly turn in the set screw until outer end of set screw is bout flush with surfce of bseplte. 13) Fully Tighten the Set Screw: Finish turning in the set screw until it hits the stop. IMPORTANT: At this time, outer end of set screw should be little bit below the surfce of the bseplte, s shown in photo A. If you hve turned in set screw s fr s it will go nd it is protruding beyond the surfce of bseplte, s shown in photo B, the most probble cuse is tht ded ltch ws not positioned properly (see Position the Ded Ltch s Set Screw Hole: on pge 10). If you hve turned the set screw in s fr s it will go nd it is protruding from the surfce of the bseplte, do the following: Turn set screw bck out so tht bout 1/4 is protruding from surfce of bseplte. Reposition criticl edge on ded ltch ccording to the instructions on pge 10). Turn set screw in until it just hits the stop. IMPORTANT: Do not overtighten set screw becuse the bseplte my strt to bow outwrd resulting in gp between trim nd door when trim is mounted. A B CORRECT INCORRECT B Pge

Instlling the KC9357/KC9357-2 14) Prep for Exit Only or New Instlltion: Prep door for device ccording to Adms Rite instructions.

Plce trnsprent self-dhesive templte on door > Center templte s circle on door s 1-3/8 hole. > Align templte s verticl guide lines prllel to door s edge.

12 Instlling the KC9357/KC ) Prep for Exit Only or New Instlltion: Prep door for device ccording to Adms Rite instructions. Do dditionl prep for rim cylinder using 1-3/8 dimeter hole insted of 1-5/32 dimeter. NOTE: This simplifies door prep. See Adms Rite instructions. Plce trnsprent self-dhesive templte on door > Center templte s circle on door s 1-3/8 hole. > Align templte s verticl guide lines prllel to door s edge. NOTE: Templte cn be lifted nd repositioned s often s required. Drill nd tp the three #10-32 holes. NOTE: If optionl blind nuts re used, see blind nut instlltion instructions for hole size nd mounting method. 15) Prep with Existing Rim Cylinder: Remove exit device Remove rim cylinder. > Refer to Adms Rite instructions for more info B Pge

Instlling the KC9357/KC9357-2 Prep with Existing Rim Cylinder (continued): Plce trnsprent self-dhesive templte

> Center 1-5/16 circle on existing cylinder hole. NOTE: The lines on templte s edges re for verticl guidnce only.

13 Instlling the KC9357/KC Prep with Existing Rim Cylinder (continued): Plce trnsprent self-dhesive templte on door. > Align templte s verticl guide lines prllel to edge of door. > Center 1-5/16 circle on existing cylinder hole. NOTE: The lines on templte s edges re for verticl guidnce only. Do not line them up with edge of door. NOTE: Templte cn be lifted nd repositioned s often s required. Drill two 3/16 di. holes Remove mteril. NOTE: If optionl blind nuts re used, see blind nut instlltion instructions for hole size nd mounting method. Drill nd tp three #10-32 holes (, b, nd c). Refer to Adms Rite instructions nd reinstll exit device. b c B Pge

Instlling the KC9357/KC9357-2 16) Prep with Existing Adms Rite Lever Trim: Remove trim.

> Align templte s verticl guide lines prllel to edge of door. > Center 1-5/16 circle on existing cylinder hole.

NOTE: Templte cn be lifted nd repositioned s often s required. Drill four 1/4 di. holes (, b, c, nd d).

Using jigsw with fine tooth metl cutting blde, cut long the four lines between the holes. Remove mteril.

14 Instlling the KC9357/KC ) Prep with Existing Adms Rite Lever Trim: Remove trim. > Refer to Adms Rite instructions for more info. Plce trnsprent self-dhesive templte on door. > Align templte s verticl guide lines prllel to edge of door. > Center 1-5/16 circle on existing cylinder hole. NOTE: The lines on templte s edges re for verticl guidnce only. Do not line them up with edge of door. NOTE: Templte cn be lifted nd repositioned s often s required. Drill four 1/4 di. holes (, b, c, nd d). NOTE: An 8600 Conceled Verticl Rod Exit Device is shown, but the 8800 Rim Exit Device is similr. Using jigsw with fine tooth metl cutting blde, cut long the four lines between the holes. Remove mteril. b d c Drill nd tp the three #10-32 holes (see pge 13) NOTE: Omit middle hole () if it s too close to lrge trim prep hole to tp properly. If optionl blind nuts re used, see blind nut instlltion instructions for hole size nd mounting method B Pge

Instlling the KC9357/KC9357-2 17) Instll

15 Instlling the KC9357/KC ) Instll Adpter Housing: Using the supplied #8-32 screw, instll the dpter housing. Verify tht hnding screw () is instlled correctly. 18) Apply Trim Gsket: Peel pper bcking from exterior gsket. Crefully pply gsket to trim s bseplte. 19) Plce Trim On Door: Align trim for with exit device interfce. Plce trim on door B Pge

Instlling the KC9357/KC9357-2 20) Prtilly Tighten Trim s Top Screw Using bll-end, 1/8 hex wrench, prtilly tighten trim s top screw.

Using smll, flt blde screwdriver, loosen the bttery cover screw () ONLY TWO TURNS COUN- TERCLOCKWISE. Slide off bttery cover (b) from bottom.

IMPORTANT: Do not cut or ttempt to remove the bttery pck s wire hrness. b 22) Instll Btteries: Remove nd retin bttery bg.

16 Instlling the KC9357/KC ) Prtilly Tighten Trim s Top Screw Using bll-end, 1/8 hex wrench, prtilly tighten trim s top screw. 21) Remove Bttery Cover: If not lredy done, insert key into cylinder nd turn it counterclockwise. Using smll, flt blde screwdriver, loosen the bttery cover screw () ONLY TWO TURNS COUN- TERCLOCKWISE. Slide off bttery cover (b) from bottom. Pull out bttery pck from bttery comprtment. Bttery pck is ttched to wire hrness. IMPORTANT: Do not cut or ttempt to remove the bttery pck s wire hrness. b 22) Instll Btteries: Remove nd retin bttery bg. IMPORTANT: DO NOT DISCARD BATTERY BAG. IT IS IMPORTANT THAT IT IS REINSTALLED AFTER THE BATTERIES ARE INSTALLED IN BATTERY HOLDER. Observe the polrity mrkings indicted on bttery holder nd instll four, AAA btteries ccordingly. Slide bttery bg onto bttery holder B Pge

Instlling the KC9357/KC9357-2 23) Fold Bttery Bg: Fold bttery bg over.

Tuck wiring netly into comprtment 25) Instll Bttery Comprtment Cover: Slide bttery

17 Instlling the KC9357/KC ) Fold Bttery Bg: Fold bttery bg over. IMPORTANT: The bttery bg is used to protect the btteries from moisture nd to insulte them electriclly from metllic prts. 24) Instll Bttery Pck: Instll bttery pck into comprtment with bg opening fcing down. Tuck wiring netly into comprtment 25) Instll Bttery Comprtment Cover: Slide bttery comprtment cover on from the bottom. IMPORTANT: Use cution not to pinch the bttery wires. Tighten bttery cover screw. Rotte key clockwise. Remove key B Pge

Instlling the KC9357/KC9357-2 26) Instll Wter Plug. Insert wter plug () into top mounting screw hole.

18 Instlling the KC9357/KC ) Instll Wter Plug. Insert wter plug () into top mounting screw hole. Using the end of smll Allen wrench or similr tool, push plug into hole pst surfce. INSTALLATION COMPLETE B Pge

19 Test Opertion Test Opertion / Dimensions KC9357/KC INSTALLATION INSTRUCTIONS Test Opertion / Dimensions 1. Turnpiece should rotte freely. 2. Insert key into cylinder nd rotte counterclockwise 180 degrees. 3. Rotte turnpiece clockwise to unlock device > Door should be ble to be opened. 4. Let go of the turnpiece nd close the door > Door should be locked. 5. Remove key. 6. Using the keypd, enter the defult ccess code: The red LED should light ech time button is pressed nd when 9 is pressed, the green LED should flsh for five seconds during which time the turnpiece should be engged nd door should be ble to be opened gin. 7. Test exit device to mke sure it is operting properly. See to Adms Rite instructions for more info. Dimensions SEE PROGRAMMING GUIDE FOR PROGRAMMING INFORMATION B Pge

20 Notes Notes NOTES B Pge

MPC COBRA SERIES. Manually Programmable Cylindrical Lock D

MPC COBRA SERIES. Manually Programmable Cylindrical Lock D 51120-D MPC COBRA SERIES Mnully Progrmmle Cylindricl Lock 575 Birch Street Forestville, CT 06010 technicl support: 866-322-1237 fx: 866-322-1233 http://www.irsupport.net 57010-H 12-19-2005 Introduction