Lincoln Under-cabinet Light Installation Instructions

Size: px

Start display at page:

Download "Lincoln Under-cabinet Light Installation Instructions"

Gary Jessie Griffith
5 years ago
Views:

1 Lincoln Under-cbinet Light Instlltion Instructions # Rev A

2 Congrtultions on your new Lincoln Under-cbinet Light! Whether purchsed for its significnt energy svings nd efficiency, lower lifetime costs, environmentl considertions, or just to find better wy to light your work re, your Lincoln Under-cbinet Light will provide consistent nd relible light from the highest qulity LEDs nd components vilble. Plese red this guide crefully nd follow the instlltion instructions. An electronic version of this guide is lso vilble on our website t Should you hve ny questions bout your Lincoln Under-cbinet Light, refer to the troubleshooting section t the end of this guide. If you still hve questions, plese contct your sles representtive, cll Customer Service t option 1 or send n emil to customerservice@workriteergo.com. From ll of us here t Workrite Ergonomics: Thnk you. A Light Fixture Qty: 1 B Mounting Prts Kit Qty: 2 Wood Mount Brckets with screws 2 Mgnetic Mounts C Trnsformer 1A, 2A OR 4A Qty: 1 1,2,3 Mx 4.0A output D 3-Pin Power Adpter 1 Qty: 1 E Jumper Cble 3", 6", 10" or 20" 4 Qty: 1 Mx 2.0A output 1 Not included with Jumper models (SKUs beginning with LIN-J). 2 Amperge determined by length of light fixture 3 Type A stndrd. Other plug types vilble 4 Only included with Jumper models (SKUs beginning with LIN-J) 2 Workrite Ergonomics

3 Typicl Configurtions Stnd-Alone Disy-Chin 1 Mount Fixture: Determine if the light will be ffixed to metl or wood cbinet nd follow the pproprite directions below.! Note: If instlling the prent unit of disy chin, be sure to position the prent unit so tht it cn be connected to the dditionl unit with its supplied jumper cble. Metl cbinet mounting: Snp Mgnetic Mounts (B) onto bck of Light Fixture (A). b B SNAP Attch Light Fixture to metl under-cbinet. Mgnets will hold the fixture in plce. Align on bck of Light. Press down to snp into ril Under-Cbinet b Plce lmp on under-cbinet A Workrite Ergonomics

4 Wood cbinet mounting: Note: You will need #2 Phillips-hed screwdriver to complete this step. b c Determine where you wnt to mount your Light nd drw stright line on the underside of the cbinet to indicte the center long the length of the Light. Be sure it is fr enough wy from the front of the cbinet to prevent the Light from protruding out from the edge. Attch Wood Mounts (B) long your line with Screws provided. Snp Light Fixture (A) onto mounts to hold in plce. Under-Cbinet B b Attch Mounts long drwn line SNAP 1" - 6" vr. Drw line prllel to edges of cbinet c Snp Light onto mounts. A 4 Workrite Ergonomics

5 2 Lincoln Under-cbinet Light Instlltion Instructions Connect Jumper Units to Prent Unit (if pplicble) Secure Jumper Cble (E) between the plug side of the Prent Unit nd the Jumper Unit. The cble should snp into plce. E Note: To remove Jumper Cble, depress the clip on the side of the plug nd pull gently from the fixture. CAUTION The number of lights tht cn be disy-chined together depends! on the size of the lights nd the size of the trnsformer. Do not exceed the totl number of lights for ech of the trnsformer sizes listed: Mximum Disy-chined units: Number of fixtures within sme chin 2A under 48" of lights or 3 lights mx 4A under 120" of lights or 5 lights mx Workrite Ergonomics

6 3 Attch Power Adpter Attch Power Adpter (D) to the Prent (or Stnd-Alone) unit nd the Trnsformer (C). C D 4 Attch Trnsformer to Wll Outlet 6 Workrite Ergonomics

7 Troubleshooting Tips The Lincoln Under-cbinet Light will not turn on Check ll wire nd cble connections. Mke sure they re completely nd fully engged. Check tht the jumper cbles or power dpter cbles hve not come loose from their connectors Mke sure tht the Trnsformer is plugged into the wll. If disy chin, ensure the correct trnsformer is used for the number of LEDs in the chin. All trnsformers should be Clss 2, 12V trnsformers. Refer to the Tble in Step 2 for required current rtings. Check tht the outlet hs power. The Lincoln Under-cbinet Light flshes on nd off Unplug the trnsformer nd locte the lbel. Mke sure tht the trnsformer is ONLY Clss 2, 12V trnsformer t 1A (1000mA), 2A (2000mA), or 4A depending on how mny LEDs re connected. The Lincoln Under-cbinet Light dims or goes out. Mke sure there re not too mny lights in the disy chin for the rting of the trnsformer. Refer to the Tble in Step 2 for guidnce. Check ll wire nd cble connections. Mke sure they re completely nd fully engged. Check tht the outlet hs power. The Lincoln Under-cbinet Light will not turn on when I come bck into the work re The occupncy sensor hs listed rnge of 15. However, if lip of the cbinet or other object blocks the full view of the sensor, then it my hve trouble detecting the presence of person in the work re. Reposition the light to hve better view of the work spce. Workrite Ergonomics

8 Troubleshooting Tips, continued The Lincoln Under-cbinet Light with n occupncy sensor will not turn off The time on the occupncy sensor utomtic shutoff is set t the fctory for 15 minutes. Cover the occupncy sensor nd record how long it tkes for the light to turn itself off. If the Lincoln Under-cbinet Light is plce ner wlkwy, isle wy or djcent to nother worksttion, the light my receive signls tht the spce it is monitoring is occupied nd the light won t shut off. Try to reposition the light wy from isle wys. If problems persist, plese contct your sles representtive or Workrite Customer Service. Replcement prts Mounting Kit...LIN-MOUNT Power Adpter...LIN-3PIN-PWR 3" Jumper Cble...LIN-3PIN-J-03 6" Jumper Cble...LIN-3PIN-J-06 10" Jumper Cble...LIN-3PIN-J-10 20" Jumper Cble...LIN-3PIN-J-20 1A Trnsformer...LIN-T15 2A Trnsformer...LIN-T25 4A Trnsformer...LIN-T45 8 Workrite Ergonomics

Two-Position Electric Duplex Room Thermostats

TC-xx Series, TC-xx Series, TF- Series Two-Position Electric Duplex Room Thermostts These thermostts provide on-off control of heting/cooling systems. Fetures: Seprte units for C nd F. All units except