All the work described in sections A, B, C, D, and E must be carried out in full before the wheel/tyre combination may be used.
|
|
- Kristian Osborne
- 5 years ago
- Views:
Transcription
1 mb cdef Instlltion Instructions Conversion to 16-inch tyres nd 7 1/2 J _ 16 H 2 ET 40 disk wheel Model 124 Excluding vehicles with specil bodywork, sedns with long wheelbse nd /036/051/091/290/393. All the work described in sections A, B, C, D, nd E must be crried out in full before the wheel/tyre combintion my be used. The instlltion instructions re divided up into the following sections: A. Permitted tyre combintions B. Detching the stndrd wheels C. Modifictions to the body D. Fitting the specil wheels E. Correction of tyre infltion pressure F. Technicl detils G. Informtion for ordering replcement prts An entry in the vehicle documents is required in the Federl Republic of Germny. For this copy of the respective smple report must be submitted to the TÜV/TÜA. Copyright DimlerChrysler AG CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 1
2 A. Permitted tyre combintions Model Front xle Rer xle Comments /030/04/ / / / / /19 205/55 R /55 R 16 All Sedns, Coupés, (including 4MATIC, excluding 24 V) 205/55 R /50 R 16 All T-Sedns (excluding 4MATIC nd 24 V) B. Detching the stndrd wheels 1 Remove wheel covers on steel disk wheels. 2 Slcken wheel bolts. 3 Rise vehicle. 4 Unscrew wheel bolts. When unscrewing the finl wheel bolt be sure tht the wheel does not suddenly tilt off the hub. 5 Remove wheel. M Five of the stndrd wheel bolts removed must be retined for the spre wheel. C. Modifictions to the body 1 Adjusting the front fender Copyright DimlerChrysler AG CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 2
3 1.1 Detch side pnel on the front fender from the fixing elements, pull to the rer nd remove. 1.2 Unscrew bolts (A nd B) on fender. 1.3 Slcken bolt (A) on side of bumper. Copyright DimlerChrysler AG CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 3
4 1.4 Press the side prt of the bumper downwrds nd unscrew the bolts for fender fixing (A nd B). Clmp spcer between fender nd body on the left nd the right. The bore holes must lign to permit troublefree fixing. 1.5 Plce one spcer on the left nd right between the fender nd body in the side re of the bumper. 1.6 Tighten ll bolts slightly in ccordnce with lyout. Tighten bolts fter visul inspection. 2 Reworking the body t the front fenders Copyright DimlerChrysler AG CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 4
5 2.1 Flttening down front fender flnge: When converting to wider wheels nd tyres the inside edges of the front fender must be flttened down to n ngle of 110 over the complete wheel cutout. 2.2 If excessive PVC underbody protection hs been pplied, grind off excess before folding bck the fender flnge. 2.3 Using hot ir gun crefully het up outer edges of fender to mximum of C. Do not overhet pint whilst pplying het (mx. 80 C). 2.4 In the mrked re (A), the fender flnge is flttened down up to the inside of the fender in severl stges. A plstic hmmer must be used to void dmging the pint. 2.5 Allow front fender flre to curve smoothly bck towrds originl, unflred line within the mrked re (B). Rectify ny dmge to pint or underbody protection. 2.6 Grind off side pnel to mtch the reworked fender contour nd ssemble. 3 Folding bck the edge of rer fender Copyright DimlerChrysler AG CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 5
6 3.1 If excessive PVC underbody protection hs been pplied, grind off excess before folding bck the edge of the fender. 3.2 Using hot ir gun crefully het up outer edges of fender to mximum of C. Do not overhet pint whilst pplying het (mx. 80 C). 3.3 In the mrked re (A), the edge of the fender is flttened down s fr s the inside of the fender in severl stges. A plstic hmmer must be used to void dmging the pint. Rectify ny dmge to pint or underbody protection. 3.4 Tret wheel rch gin with underbody protection. Spry the folded bck fender edges with body cvity preserver. D. Fitting the specil wheels Copyright DimlerChrysler AG CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 6
7 1 Screw in centering bolts (tool kit) in upper tpped hole of the wheel hub. 2 Put on AMG light lloy wheel nd press onto wheel hub. 3 Screw in wheel bolts nd tighten positively. The wheel bolts must be dry nd free from grese. Ensure tht the wheels re not tensioned by tightening the wheel bolts on one side. (Tighten wheel bolts digonlly in severl stges). M Only M12 x 1.5 x 40 mm sphericl collr bolts supplied with the rims re to be used for the wheel fixing. 4 Unscrew centering bolt nd replce by wheel bolt. 5 Lower vehicle. 6 Evenly tighten wheel bolts digonlly to tightening torque of 110 Nm. M AMG light lloy wheel bolts must be retightened fter km. (Tightening torque 110 Nm). Fitting snow chins is not permitted. E. Correction of tyre infltion pressure The minimum tyre infltion pressures required cn be obtined from the tyre infltion pressure tble (ppendix). The front xle or rer xle tyre infltion pressures determined re to be noted on the AMG sticker using wterproof felt tip pen. Attch sticker to suitble point on the loding edge of luggge comprtment. Copyright DimlerChrysler AG CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 7
8 F. Technicl detils Mnufcturer: AMG/RUOTE OZ Model: C Wheel size: 7 1/2 J _ 16 H 2 Offset: Pitch circle: Permitted wheel lod: Centering: Type: 40 mm d=112 mm, 5 hole 615 kg t rdyn=307 mm Centrl centering d= One-piece light lloy wheel with double hump Mrking: Outer side of wheel: AMG Germny C /2 J _ 16 H 2 ET 40 Inner side of wheel: RUOTE OZ (foundry symbol) nd dte of mnufcture Vlves: Metl screw-on vlves in ccordnce with DIN 7779 with long nut Fixing: Tightening torque: Blnce weights: Only with M12 x 1.5 x 40 mm sphericl collr bolts supplied by the wheel mnufcturer 110 Nm Only dhesive weights re permitted G. Informtion for ordering replcement prts Replcement prts Designtion Prt no. Copyright DimlerChrysler AG CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 8
9 Light lloy disk wheel 7 1/2 J _ 16 H 2 ET 40 B Wheel trim B Sphericl collr bolt L=40 mm H WA Vlve H WA Tyre pressure sticker H WA Fender extension kit B A set of wheel locking bolts (Prt no. B ) cn be supplied upon request. Conversion to AMG 7 1/2 J _ 16 H 2 ET 40 disk wheel Refer to pge 2 for tyre dimensions. Pssenger cr Model 124 sedn/coupé/t-model The ppendix is divided up into the following sections: A. Assignment of tyre mke/model B. Specified minimum tyre infltion pressures A. Permitted mkes of tyre Vehicle model 124 Mke Description Sedn Coupé T-model Bridgestone RE 71 X X X Michelin MXX X X X Dunlop SP Sport D 40 X X X Pirelli P 700 Z X X X Pirelli P 700/P 7 X X not permitted Goodyer Egle VR/NCT X X not permitted B. Specified minimum tyre infltion pressures (br) Copyright DimlerChrysler AG CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 9
10 Refer to pge 2 for tyre dimensions. Vehicle model: 124 sedn/coupé/t-model Permitted mximum speed Vmx (km/h)1) Front xle Rer xle Level control system Perm. rer xle lod (kg)1) Permitted front xle lod (kg)1) Steel suspension Perm. rer xle lod (kg)1) 205/55 225/50 205/55 up to 1015 up to 1055 up to 1025 up to 1230 up to /50 up to 1230 Mx. wheel cmber ngle (degrees) ' ' 1) Vlues for mximum speed nd permitted front xle or rer xle lods cn be obtined from the vehicle documents. Comments: Tyre infltion detils only pply for vehicles with mximum speed of up to 250 km/h. The tyre infltion pressure cn be reduced by p = 0.1 (br) per 100 kg reduction in xle lod. Remember tht tyre infltion pressure detils only pply for cold tyres! On wrm tyres vlues of up to 0.5 br higher re permissible. Do not reduce pressure of wrm tyres! Tyre infltion pressure my only be corrected when tyres re cold! Tyre infltion pressure detils relte to the use of permitted mximum speed nd permitted xle lod. Copyright DimlerChrysler AG CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 10
Conversion to 235/45 R 17 tyres and 8 J x 17 H 2 ET 28 disk wheel 40.01
mb s Instlltion Instructions Conversion to 235/45 R 17 tyres nd 8 J x 17 H 2 ET 28 disk wheel 40.01 Model 124 Excluding vehicles with specil bodywork, sedns with long wheelbse nd 124.020/036/120. All the
More informationSuspension Control Module
User Mnul Suspension Control Module 0099 Before Instlltion Wrning: This owering Module should be instlled by n individul with extensive knowledge in electronics, including: wire identifiction, extrcting
More informationDRIVE SHAFTS INDEX
DRIVE SHAFTS 8 70237 Tble of Contents Pge Specifictions............................... 8-1 Torque Specifictions..................... 8-1 Specil Tools............................ 8-1 Lubricnts, Selnts,
More informationABB industrial drives. Mechanical installation instructions ACS880 multidrive cabinets
ABB industril drives Mechnicl instlltion instructions ACS880 multidrive cbinets List of relted mnuls Generl drive mnuls (in ll deliveries) Electricl plnning instructions for ACS880 multidrive cbinets nd
More informationInstallation and Operational Instructions for ROBA -slip hubs Sizes 0 12 (B.1.0.GB)
Plese red these Opertionl Instructions crefully nd follow them ccordingly! Ignoring these Instructions my led to mlfunctions or to clutch filure, resulting in dmge to other prts. These Instlltion nd Opertionl
More informationREPLACEMENT. 4. REMOVE WINDSHIELD MOULDING OUTSIDE (a) Using a knife, cut off the moulding, as shown in the illustration.
7012 REPLCEMENT The instlltion procedures re the removl procedures in reverse order. However, only instlltion procedures requiring dditionl informtion re included. 1. REMOVE ROOF HEDLINING SSY (See pge
More informationWINDSHIELD / WINDOWGLASS
WINSHIEL / WINOWGLSS QURTER WINOW GLSS QURTER WINOW GLSS OY WINSHIEL / WINOWGLSS OMPONENTS 97 RER SIE SETK FRME LH RER SIE SETK FRME RH RER SET USHION SSEMLY RER OOR OPENING TRIM WETHERSTRIP LH TONNEU
More informationTeile und Zubehör- Einbauanleitung
Teile und Zubehör- Einbunleitung F 46 052 EVA BMW Prts nd Accessories Instlltion Instruction Sun blind, electric BMW 3 Series Sloon (E46/4), BMW 3 Series Coupé (E46/2) Best.-Nr. 0 29 0 000 58 I/99 Printed
More informationSeries 250 Type and Type Pneumatic Control Valves Type 3251 Globe Valve
Series 250 Type 3251-1 nd Type 3251-7 Pneumtic Control Vlves Type 3251 Globe Vlve DIN version Appliction Control vlve for process engineering pplictions with high industril requirements Nominl size DN
More informationDecor Radiators Baseboard
Decor Rditors Bsebord Pedestl 11 (with fins) Avilble in outputs from 1,561 to 10,282 Btu/hr; 2, nd 4 tubes high. 28 (igh Output, with fins) Avilble in outputs from 5,05 to 19,552 Btu/hr; 2 nd 4 tubes high.
More informationKING COBRA/KING COBRA-2 NARROW STILE SERIES KC9357/KC9357-2
KING COBRA/KING COBRA-2 NARROW STILE SERIES KC9357/KC9357-2 Keypd Progrmmble nd SNAP Comptible Trim For Rim Exit Devices Mounted On Aluminum Doors. 57047-B 04-2007 Contents of the Box KC9357/KC9357-2 INSTALLATION
More informationWATERTIGHT AIRTIGHT SPECIAL ACCESS DOORS & HATCHES, PART 1 GENERAL
SECTION 08316 WTERTIGHT IRTIGHT SPECIL CCESS DOORS & HTCHES, PRT 1 GENERL HIGHLIGHTED RES TO BE INSERTED BY SPECIFYING ENGINEER. 1.1 WORK OF THIS SECTION. THE WORK OF THIS SECTION INCLUDES PROVIDING LL
More informationRPEA3-06. Functional Description HA /2011. Directional Control Valves Solenoid Operated with 8W Coil. Replaces HA /2007
Directionl Control Vlves Solenoid Operted with 8W Coil RPEA3-06 0/20 Size 06 (D 03) 350 br (5076 PSI) 80 L/min (2 GPM) Replces 2/2007 /3-, /2- wy directionl control vlves Enclosure type to IP65 Push button
More informationTeile und Zubehör - Einbauanleitung
Teile und Zubehör - Einbunleitung F 36 0305 EVA Originl BMW Zubehör-Heckschürze BMW Z3 rodster (E 36/7) b 04/99 BMW Prts nd Accessories Instlltion Instruction Originl BMW ccessory rer pron BMW Z3 rodster
More informationCable Trolleys for C-Rails Program
Cble Trolleys for C-Rils Progrm 02 0 0260 Contents C-Ril nd Accessories Progrm 02 C-Ril x... 2 Trck Coupler... 2 End Stop... 2 Trck Support Brcket... 2 Support Arm nd Girder Clip... 3 Brcket... 3 Cble
More informationFour-Row Tapered Roller Bearings. Mounting Instructions
Four-Row Tpered Roller Berings Mounting Instructions Contents Mounting instructions for four-row tpered roller berings 1. Preprtions for mounting... 4 2. Checking the roll neck nd chock... 5-6 3. Arrnging
More informationJET PUMP. Table of Contents. Section 5 - Jet Pump
Tble of Contents JET PUMP Section 5 - Jet Pump JET PUMP Generl Informtion..................... 5-2 Principles of Opertion................ 5-2 Mster Specifictions Jet Pump........... 5-3 Specil Tools........................
More informationThe quick jaw change chuck KNCS-NB / KNCS-NBX can use all existing top jaws KNCS-NB
Fst chngeover, fst pybck: The quick jw chnge chuck KNCS-NB / cn use ll existing top jws KNCS-NB/: cn use existing jws Miniml set-up times Jw chnge in less thn 1 minute KNCS -NB High repetbility when chnging
More informationPOWER TRIM. Table of Contents. Section 5D - Auto Trim II
SERVICE MANUAL NUMBER 14 Tble of Contents POWER TRIM Section 5D - Auto Trim II AUTO TRIM II 1 B Auto Trim II System................. 5D-2 Description...................... 5D-2 Auto Trim II Opertion...............
More informationRPE3-06. Functional Description HA /2008. Solenoid Operated Directional Control Valves. Replaces HA /2006
Solenoid Operted Directionl Control Vlves RE3-06 10/2008 Size 06 p mx up to 320 br Q mx up to 80 L/min Replces 11/2006 4/3, 4/2 wy directionl control vlves Solenoids cn be turned round their xis to ny
More informationUPS Pure Sinewave UPS
UPS Pure Sinewve UPS USR S MANUAL 1.6K / 3.2K / 5KVA 6.4K / 8K/ 10KVA 1. INTRODUCTION 1. 1.1 Generl Description This UPS, powerful ll-in-one solution, delivers unsurpssed clen true sine wve output power
More information11 263/ Radial Piston Pump Model R4 /Series 2X Fixed Displacement. Ordering Code 1 PF 1 R4 2X R Replaces:
ize.60 to 0.00 Rdil iston ump Model R4 /eries X Fixed Displcement 0,0 I (00 br).9 in /rev (9.4 cm /rev) RA 6/0.9 RA 6/0.9 Replces: 06.89 K 6/ Rdil piston pump with 0 pistons nd prllel shft Chrcteristics:
More informationTeile und Zubehör - Einbauanleitung
Teile und Zubehör - Einbunleitung F 46 0256 EVA BMW Zubehör-Seitenschweller BMW 3er Coupé (E46/2) BMW Prts nd Accessories Instlltion Instruction BMW Accessory side skirt BMW 3 Series Coupé (E 46/2) Instructions
More informationRPE3-06. Functional Description HA /2011. Directional Control Valves Solenoid Operated. Replaces HA /2009
Directionl Control Vlves Solenoid Operted RE3-06 Size D 06 (03) 350 br (5076 SI) 80 L/min(21 GM) Size D 06 (03) p mx 320 br (4641SI) ccording to CSA 80 L/min(21 GM) HA 4010 11/2011 Replces HA 4010 12/2009
More informationAssembly instructions
Assemly instructions Comi Stemer Unit Model Type of energy Unit type Trnsltion from the originl document 10013865-0AMDE-- 1/4/2017 FlexiComi MgicPilot FlexiComi Clssic 6.15 6.21 10.15 10.21 20.15 20.21
More informationFRONT SIDE FIX WINDOW
WINSHIEL/WINOWGLSS/MIRROR FRONT SIE FIX WINOW REPLEMENT FRONT SIE FIX WINOW The instlltion procedures re the removl procedures in reverse order. However, only instlltion procedures requiring dditionl informtion
More informationDIESEL EGT GAUGE INSTALLATION INSTRUCTIONS P14D AA
DIESEL EGT GUGE INSTLLTION INSTRUCTIONS P4D4-9235- Revision: - Dated 3/9/4 Replaces: None DIESEL EGT GUGE INSTLLTION HRDWRE CONTENTS P4D4-44- - DIESEL EGT GUGE KIT COMPONENT - DIESEL EGT GUGE SSY (PRT
More informationu-tec UT Our change system, that makes EVERYTHING possible
u-tec UT Our chnge system, tht mkes EVERYTHING possible Terms nd conditions: You will find them on our website www.heimtec.com Home/Imprint/Terms nd Conditions This ctlogue, including ll its prts, is protected
More informationExcluding vehicles with special bodywork, 4MATIC, sedan with long wheelbase and all types without level control system on the rear axle and
amb cdef Installation Instructions Conversion to AMG sports chassis Model 14 3.03 Excluding vehicles with special bodywork, 4MATIC, sedan with long wheelbase and all types without level control system
More informationCONTROL VALVES FOR GRINDER. Installation, Maintenance and Operating Instructions 5 GA 71 en Issue 5/02
CONTROL VALVES FOR GRINDER Instlltion, Mintennce nd Operting Instructions 5 GA 71 en Issue 5/02 2 Tble of Contents 1 OPERATION......................... 3 1.1 Generl......................... 3 1.2 Min components.................
More informationTECHNICAL INSIGHT INTERNAL CLEARANCE - TYPES AND NORMS
TECHNICAL INSIGHT PRODUCT AND APPLICATION ENGINEERING INFORMATION A PUBLICATION OF NSK AMERICAS INTERNAL CLEARANCE - TYPES AND NORMS Internl clernce is the distnce which the two rings of non-instlled bering
More informationSpark Plug Fouling 3.0 Liter OptiMax
WARRANTY INFORMATION PARTS INFORMATION SERVICE INFORMATION Bulletin No. 2002-07 Circulte to: Sles Mnger Accounting Service Mnger Technicin Prts Mnger Sprk Plug Fouling 3.0 Liter OptiMx Models Affected
More informationBIMETAL-POINTER-THERMOMETER
BIMETA-POINTER-THERMOMETER Chemicl version cc. EN 30 byonet cse IP 6 With or without filling Suitble for chemicl nd petrochemicl industry, food, pulp nd pper industry nd for mchine nd pprtus contruction.
More informationConversion to AMG sports suspension Model 129 without level control on rear axle
Installation instructions Conversion to AMG sports suspension Model 129 without level control 32.10 on rear axle Models 129.058/060/061/063/066/067 - USA versions are excluded. These installation instructions
More informationExcluding vehicles with special bodywork, 4MATIC, sedan with long wheelbase and all types with level control on the rear axle and
amb cdef Installation Instructions Conversion to AG sports chassis odel 124 32.02 Excluding vehicles with special bodywork, 4ATIC, sedan with long wheelbase and all types with level control on the rear
More information2/2 Solenoid Operated Seat Valve, ISO Size 03
2/2 Solenoid Operted Set Vlve, ISO Size 03 Q mx = 20 l/min (5.3 gpm), p mx = 315 r (4500 psi) Sndwich design, idirectionl lek-proof shutoff, direct cting, with EX-sfty sol. coil Vlve: With crtridge vlve,
More informationPOWER TRIM. Table of Contents. Section 5D - Auto Trim II
SERVICE MANUAL NUMBER 11 Tble of Contents POWER TRIM Section 5D - Auto Trim II AUTO TRIM II Auto Trim II System................... 5D-2 Description........................ 5D-2 Auto Trim II Opertion.................
More informationAppendix E D791 and T791 Head and Valve Holddown Assembly Details
Appendix E D nd T Hed nd Vlve Holddown Assemly Detils Hed First Stge Holddown Assemly (") Suction with Unloder Suction (Stndrd) First Stge Holddown Assemly (") Dischrge See figure A 0 CAUTION: Alwys relieve
More informationMODEL 1200 WATER WHEEL TRANSPLANTER OPERATING MANUAL
MODEL 1200 WATER WHEEL TRANSPLANTER OPERATING MANUAL Tble Of Contents Axle, Tire... 3 Fetures... 13 Foot Rest... 4 Helpful Tips... 14 Options... 13 Prts Brekdown, Description...10-12 Prts Brekdown, Exploded
More informationSpecifiable Features. Compatible with all UL 1686 listed plugs and receptacles. Type P Cable. Lockout Compliant. PowerMate Features and Benefits
PowerMte Fetures nd Benefits Type P Cle Lockout Complint Specifile Fetures Lockout Plug Sfety Insultor Dimond Clmp Split Pin Contcts Type P Cle Comptile with ll UL 686 listed plugs nd receptcles. 2 3 4
More informationJUMO MIDAS S05 OEM pressure transmitter - universal
Delivery ddress: Mckenrodtstrße 4 609 Fuld, Germny Postl ddress: 605 Fuld, Germny Phone: +49 66 600-0 Fx: +49 66 600-607 Hrlow, Essex CM0 DY, UK Phone: +44 79 655 Fx: +44 79 656 Cnstot, NY 0, USA Phone:
More informationFUEL SYSTEM. Table of Contents. Specifications. Section 3A Electric Fuel Pump FUEL SYSTEM. Fuel Recommended Gasoline Recommended Oil
FUEL SYSTEM Section 3A Electric Fuel Pump Tble of Contents Specifictions........................... 3A-1 Fuel Pump Assembly.................... 3A-2 Specil Tools........................... 3A-3 Fuel Lift
More information631 ALLOWANES AND TOLERANCES
631 ALLOWANES AND TOLERANCES ANSI Fits. Tbles 3 through 9 inclusive show series of stndrd types nd clsses of fits on unilterl hole bsis, such tht the fit produced by mting prts in ny one clss will produce
More informationMPC COBRA SERIES. Manually Programmable Cylindrical Lock D
51120-D MPC COBRA SERIES Mnully Progrmmle Cylindricl Lock 575 Birch Street Forestville, CT 06010 technicl support: 866-322-1237 fx: 866-322-1233 http://www.irsupport.net 57010-H 12-19-2005 Introduction
More informationElectrically operated directional spool valve with a soft-shift function type WE10P NS 10. up to 35 MPa up to 120 DATA SHEET - OPERATION MANUAL
LICTION Electriclly operted directionl spool vlve with soft-shift function type WE10 NS 10 Electriclly operted directionl spool vlve type WE10 is intended for chnging the direction of fluid flow in hydrulic
More informationLincoln Under-cabinet Light Installation Instructions
Lincoln Under-cbinet Light Instlltion Instructions #1500178 Rev A Congrtultions on your new Lincoln Under-cbinet Light! Whether purchsed for its significnt energy svings nd efficiency, lower lifetime costs,
More information(mω) 1. Temperature ( C) Voltage (V) ULRG1 /
Resistors Metl Strip Current Sense Resistors Surfce Mount Metl Element Current Metl Element Sense Resistor UR Series UR Current Series Sense Resistor Mke Possible Resistnce R0005 (m ) to R015 (15m ) Metl
More information2/2 Solenoid Operated Seat Valve, ISO Size 03
2/2 Solenoid Operted Set Vlve, ISO Size 03 Q mx = 40 l/min (11 gpm), p mx = 315 r (4500 psi) Sndwich design, idirectionl lek-proof shutoff, direct cting, electriclly operted 1 Description 2 echnicl dt
More informationFUEL SYSTEM. Section 3A Pulse Crankcase Driven Fuel Pump. Model 200/225 DFI. 1. Fuel Pressure/Vacuum Gauge (0-15 psi) (Obtain Locally)
FUEL SYSTEM Section 3A Pulse Crnkcse Driven Fuel Pump Tle of Contents Specifictions................................ 3A-1 Specil Tools................................ 3A-1 Fuel Pump..................................
More informationConversion to AMG sports chassis Model
Installation Instructions Conversion to AMG sports chassis Model 201 32.01 Excluding vehicles with level control system on the rear axle and 201.034/035/036. Towing equipment not permissible as special
More informationCC-410 KIT SERIES INSTRUCTION SHEET
(COMPLETE CC-410-W KIT ILLUSTRTED. CUT-OUTS IN TRCK & FSCI TO EXPOSE COMPONENTS) CC-410 KIT SERIES INSTRUCTION SHEET CROWDERTRCK S CTCH N CLOSE TM SYSTEM PREVENTS BOUNCING ND SLMG OF SLIDING DOORS. CN
More information* * * 3700 LOBBY CASH RECYCLER. REAR LOAD 13mm ( 2") UL SAFE - 15" DISPLAY OR 19" DISPLAY WITH DETAILS FOR OPTIONAL VESTIBULE INSTALLATION
R L CLL -0--600 64 SFE ( 6 ") DIEBOLD 00 LOBBY CSH RECYCLER RER LOD mm ( ") UL SFE - " DISPLY OR " DISPLY WITH DETILS FOR OPTIONL VESTIBULE INSTLLTION CONSULT WITH DIEBOLD INSTLLTION/SERVICE BRNCH FOR
More information* * * DIEBOLD 3700 LOBBY CASH RECYCLER- FRONT LOAD 15" DISPLAY OR 19" DISPLAY CONSUMER ACCESS DIMENSIONS PLAN VIEW 19" DISPLAY FRONT ELEVATION
R L CLL -0--600 64 SFE ( 6 ") DIEBOLD 00 LOBBY CSH RECYCLER- FRONT LOD " DISPLY OR " DISPLY WITH mm ( ") UL SFE CONSULT WITH DIEBOLD INSTLLTION/SERVICE BRNCH FOR DDITIONL DETILS ND INFORMTION. PLESE SEE
More information152mm (6") DIA. POINT TO POINT SYSTEM PVC OR STEEL TUBE SYSTEM TYPE I AND TYPE II OVERHEAD UNITS TYPE I OVERHEAD UNIT TYPE II OVERHEAD UNIT NOTES:
2mm ") DI. POINT TO POINT SYSTEM PVC OR STEEL SYSTEM L84 CLL -800--600 TYPE I ND TYPE II OVERHED UNITS 4 6 ") ( 8 ") 6 8 ") ( -0 PLN VIEW 20 (8 28 8 ") ( 8 ") 4 ( -4") 2 (4 ( 8 ") 28 ( 8 ") THE TYPE I
More informationPREFILL AND EXHAUST VALVE PV 100 TO PV 200
PREFILL ND EHUST VLVE Ref. No. Relese 08/2006 1 Description Set type construction. llows free flow from it's port to port. Flow from port to port cn e hd y pplying pilot pressure to it's port. The decompression
More informationSEE PAGES 3 AND 4 OF 7 FOR 3700 CASH RECYCLER THROUGH THE WALL WITH VESTIBULE TRIM KIT REFERENCE FRONT EDGE OF BEZEL FOR DEPTH DIMENSIONS
R DIEBOLD 00 LOBBY CSH RECYCLER- RER LOD L2 CLL -0--600 64 SFE (2 6 ") 40mm ( 6") CEN I SFE - " DISPLY OR " DISPLY WITH DETILS FOR OPTIONL VESTIBULE INSTLLTION CONSULT WITH DIEBOLD INSTLLTION/SERVICE BRNCH
More information4/2 and 4/3 Solenoid Directional Valve, ISO Size 03
4/ nd 4/3 Solenoid Directionl Vlve, ISO Size 03 Q mx = 60 l/min, p mx = 315 r wo-stge design, with EX-sfty solenoid coil Vlve: High switching relilility thnks to two-stge follower spool design Slip-on
More informationPOWERHEAD. Section 4A - Cylinder Head. Rocker Shaft and Rocker Arm... 4A-21 Camshaft... 4A-22 Cylinder Head... 4A-24
POWERHEAD Section 4A - Cylinder Hed CYLINDER HEAD Tle of Contents Specifictions........................... 4A-2 Specil Tools........................... 4A-4 Cylinder Hed.......................... 4A-6
More informationELECTRICAL. Table of Contents. Section 2A - Ignition
Tble of Contents Specifictions........................... A- Specil Tools........................... A- Flywheel............................... A- Flywheel............................... A-5 Electricl
More informationDT-466 JTG DYNAMIC LIQUID PROPANE INJECTION DIESEL INSTALLATION MANUAL P11X AB
DT-466 JTG DYNMIC LIQUID PROPNE INJECTION DIESEL INSTLLTION MNUL P11X4-9215-B Revision: B - Dated 11/26/12 Replaces: - Dated 10/1/12 INTRODUCTION! SFETY WRNING RED BEFORE STRTING THE INSTLLTION OF THE
More informationArcadia ssembly Instructions. 501x363x242cm / 16 5"Lx11 103/4"x7 111/4"
A ssemly Instructions Arcdi 5000 English_71087 501x36342cm / 16 5"Lx11 103/4"x7 111/4" Compny informtion: Plrm Americs Inc. 9735 Commerce Prkwy Kutztown, PA, USA Service Center: Toll Free: (877) 627-8476
More informationThe original quick jaw change power chuck KNCS -NB KNCS -NBX >> ALL EXISTING TOP JAWS CAN USED.
Fst chngeover, fst pybck: The originl quick jw chnge power chuck KC - KC -X ARE TROU OE EXTRA ARE TROU OE >> A EXITI TOP JAW CA UED. Miniml set-up times Jw chnge in less thn 1 minute igh repetbility when
More informationMurtfeldt Internet Chain Tensioners for Roller Chains to DIN8187
Murtfeldt Internet www.murtfeldt.de Chin Tensioners for Roller Chins to DIN8187 185 186 Murtfeldt E-mil info@murtfeldt.de Murtfeldt Fxline +49-231- 25 10 21 Chin Tensioners with Arc Segment Profile for
More information3700 LOBBY CASH RECYCLER. REAR LOAD 13mm ( 2") UL SAFE - 15" DISPLAY OR 19" DISPLAY WITH DETAILS FOR OPTIONAL VESTIBULE INSTALLATION
R L CLL -0--600 64 SFE ( 6 ") DIEBOLD 00 LOBBY CSH RECYCLER RER LOD mm ( ") UL SFE - " DISPLY OR " DISPLY WITH DETILS FOR OPTIONL VESTIBULE INSTLLTION CONSULT WITH DIEBOLD INSTLLTION/SERVICE BRNCH FOR
More informationProduct range MEGAlife
Product rnge Fx enquiries: +49 89 76909-11 sles@iwis.com MEGAlife MEGAlife mintennce free roller nd conveyor chins cn be pplied in ll res where post instlltion lubriction is not t ll or only prtly possible.
More informationEXTERIOR GROUP CONTENTS FRONT BUMPER ASSEMBLY REAR WIPER AND WASHER REAR BUMPER ASSEMBLY MARK...
5- GROUP 5 CONTENTS FRONT BUMPER SSEMBLY 5- FRONT BUMPER SSEMBLY 5- REMOVL ND INSTLLTION 5- DISSSEMBLY ND SSEMBLY 5- RER BUMPER SSEMBLY 5-5 RER BUMPER SSEMBLY 5-5 REMOVL ND INSTLLTION 5-5 DISSSEMBLY ND
More informationELECTRICAL SYSTEM 4 D INSTRUMENTATION
ELECTRICAL SYSTEM 4 D 72747 INSTRUMENTATION Tle of Contents Pge Identifiction............................. 4D-1 Specil Informtion....................... 4D-1 Lighting Options....................... 4D-1
More informationPush-in RTD temperature probe for heat meters with connecting cable for thermowells (type PS/PL)
elivery ddress: Mckenrodtstrße 14 36039 Fuld, Germny Postl ddress: 36035 Fuld, Germny Fx: +49 661 6003-607 Emil: mil@jumo.net Temple Bnk, Riverwy Hrlow, Essex, CM20 2Y, UK Fx: +44 1279 62 50 29 Emil: sles@jumo.co.uk
More informationJUMO MIDAS C18 SW. OEM seawater pressure transmitter. Applications. Brief description. Customer benefits. Special features. Approvals/approval marks
Pge /8 JUMO MIDAS C8 SW OEM sewter pressure trnsmitter Applictions wter tretment reverse osmosis, e.g. sewter deslintion plnts purifiction plnts orgnic cids, e.g. cetic cid solutions contining chloride,
More information2/2 4/4 Solenoid Directional Seat Valve, ISO Size 03
2/2 4/4 Solenoid Directionl Set Vlve, ISO Size 03 Q mx = 20 l/min, p mx = 315 r idirectionl set-vlve shut-off, direct cting, electriclly operted 1 Description he W2N / W2 series of 2/2 4/4 solenoid operted
More informationEngine Mechanical. Table of Contents. Section 3B - Engine Inspection and Assembly. Engine Inspection and Assembly
Engine Mechnicl Tle of Contents Section 3B - Generl Specifictions... 3B-2 Engine Specifictions...3B-3 Cylinder Hed... 3B-3 Cylinder Bore... 3B-3 Oil Pump... 3B-3 Piston Bore Clernce...3B-3 Piston Rings...3B-3
More informationRoller and ball bars for easy and safe die change
Roller nd bll brs for esy nd sfe die chnge T-slot tolernces cc. to DIN 6 b c h n min. mx. mx. 8 H8 + +,6 H8 37 +3 +,6 8 H8 +4 0 + 48 56,6 H8 56 +4 5 +3 6 7,5 Dimensions in mm h min. = smllest dimension
More informationSMP-BC Mixproof Valve
. kythe Proven Mixproof Rnge SMP-BC Mixproof Vlve Concept SMP-BC is snitry pneumtic set vlve, designed for sfety nd lek detection when two different products flow through only one vlve. The vlve is often
More informationAIRCRAFT ENGINES SERVICE INSTRUCTION ENGINE START AT LOW TEMPERATURES AT ROTAX SI R1
d03161 RECOMMENDED AIRCRAFT ENGINES SERVICE INSTRUCTION ENGINE START AT LOW TEMPERATURES AT ROTAX ENGINE TYPE 912 AND 914 (SERIES) Repeting symbols: Plese, py ttention to the following symbols throughout
More informationTRANSOM ASSEMBLY. Table of Contents. Section 4A - Service Procedures Requiring Minor Disassembly. Shift Cable... 4A-19
SERVICE MANUAL NUMBER 14 SERVICE PROCEDURES REQUIRING MINOR DISASSEMBLY TRANSOM ASSEMBLY Section 4A - Service Procedures Requiring Minor Disssemly Tle of Contents Specifictions....................... 4A-2
More informationCCS-810 KIT SERIES INSTRUCTION SHEET
(COMPLETE KIT ILLUSTRTED. CUT-OUTS IN TRCK & FSCI TO EXPOSE COMPONENTS) CCS-810 KIT SERIES INSTRUCTION SHEET CROWDERTRCK S CTCH N CLOSE TM SYSTEM PREVENTS BOUNCING ND SLMMING OF SLIDING DOORS. CN BE INSTLLED
More informationJUMO MIDAS C08. OEM Pressure Transmitter Basic. Applications. Brief description. Special features. Customer benefits
Mckenrodtstrße 4 609 Fuld, Allemgne 605 Fuld, Allemgne Tél. : +49 66 600-0 Fx. : +49 66 600-607 B.P. 4500 57075 Metz Cedex, Frnce Tél. : + 87 7 5 00 Fx. : + 87 7 89 00 Industriestrße 8 4700 Eupen, Belgique
More informationMANUFACTURING CO. THE FIRST NAME IN QUALITY COUPLINGS
MNUFCTURING CO. THE FIRST NME IN QULITY COUPLINGS 2016 TTENTION! End Users must read and follow this information. DISTRIBUTORS & OEM S: Please ensure that your customers are made aware of the following
More informationDV MECHANICAL ADJUSTMENT MANUAL V
DV MECHANICAL ADJUSTMENT MANUAL V Ver.0 000. 0 R MECHANISM Plese use this mnul with the service mnul. For detils on printed circuit bords digrm, schemtic digrm, nd electric prts list regrding this mechnism
More informationMANN+HUMMEL Oil-bath air cleaner Single-stage air cleaner without spare parts
MANN+HUMMEL Oil-th ir clener Single-stge ir clener without spre prts 57 Oil-th ir clener: Servicing without spre prts The proven oil-th ir cleners from MANN+HUMMEL re suitle for light to medium dust conditions
More informationUNIVERSAL ALUMINIUM CASE
UC SERIES UNIVERSAL ALUMINIUM CASE 3 2 4 Simple structure nd tough cse with extruded luminium covers. 36 sizes nd 3 different colors for totl of 108 different combintions re vilble. 2 or 3 grooves vilble
More informationTransmission and Driveline. Section 2A - Transmission and Driveline
Trnsmission nd Driveline Trnsmission nd Driveline Tle of Contents Section 2A - Trnsmission nd Driveline 2 A Generl Informtion...2A-2 Ger Rtio Selection...2A-2 Engine nd Propeller Shft Instlltion Angle...2A-2
More informationIGNITION SYSTEM SERVICE MANUAL NUMBER
IGNITION SYSTEM SERVICE MANUAL NUMBER 26 Specifictions Timing Timing (At Idle rpm) 1 1 BTDC 2 / 1 ATDC 3 / 2 ATDC 4 1 Timing must be set using specil procedure s outlined in this section. Timing cnnot
More informationCCD-493 KIT SERIES INSTRUCTION SHEET
(COMPLETE CCD-493-W KIT ILLUSTRTED. CUT-OUTS IN TRCK TO EXPOSE COMPONENTS) CCD-493 KIT SERIES INSTRUCTION SHEET CROWDERTRCK S CTCH N CLOSE TM SYSTEM PREVENTS BOUNCING ND SLMMING OF SLIDING S. CN BE INSTLLED
More informationMANUFACTURING CO. (503) (800) THE FIRST NAME IN QUALITY COUPLINGS
MNUFCTURING CO. THE FIRST NME IN QULITY COUPLINGS 2016 www.premier-mfg.com (503) 234-9202 (800) 255-5387 TTENTION! End Users must read and follow this information. DISTRIBUTORS & OEM S: Please ensure that
More informationSECTION D Engine 6.0L Diesel
303-01D-i Engine 6.0L Diesel 303-01D-i SECTION 303-01D Engine 6.0L Diesel CONTENTS PAGE SPECIFICATIONS... 303-01D-2 303-01D-2 Engine 6.0L Diesel 303-01D-2 SPECIFICATIONS Mteril Fill Cpcity Gsket Mker TA-16
More informationBRAVO STERN DRIVE 3 B DRIVE SHAFT HOUSING
RVO STERN DRIVE 7 DRIVE SHFT HOUSING Tle of ontents Pge Specifictions............................... -1 Torque Specifictions..................... -1 Specil Tools............................ -1 ering Prelods.........................
More informationPOWER COMBICON Plugs and Headers PC 6/ for Currents up to 41 A, mm Pitch
POWER COMBICON Plugs nd Heders PC 6/ for Currents up to 41 A, The PC 6 plug connector fetures highly conductive metl lloys to offer current crrying cpcity of 41 A t rted voltge of 1000 V. A double steel
More informationFINGER STRIPS. and other EMI shielding products. Characteristics
BERYLLIUM COPPER CONTCT FINGER STRIPS nd other EMI shielding products ppliction Due to their outstnding mteril nd electricl chrcteristics, eryllium copper fingers of different shpes nd dimensions re used
More informationSECTION C Engine 6.0L Diesel
303-01C-i Engine 6.0L Diesel 303-01C-i SECTION 303-01C Engine 6.0L Diesel CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 6.0L Diesel 303-01C-2 SPECIFICATIONS Mteril Gsket Mker TA-16 Motorcrft
More informationConversion to AMG sports suspension Model 140 (Coupé) with level control on the rear axle 32.14
Installation instructions Conversion to AMG sports suspension Model 140 (Coupé) with level control on the rear axle 32.14 Models 140.063/070/076 Valid for vehicles with new, retracted rear axle spring.
More informationBODY Click on the applicable bookmark to selected the required model year. Purchased from
BODY Click on the applicable bookmark to selected the required model year. Purchased from 42- BODY CONTENTS HOOD... FENDER... 5 FUEL FILLER DOOR... 6 WINDOW GLSS... 8 DHESIVES... 8 SPECIL TOOL... 8 WINDOW
More informationKeep User Manual in vehicle USER MANUAL. IN-100UM Rev. A
Keep User Mnul in vehicle USER MANUAL IN-100UM Rev. A 3 IMPORTANT SAFETY INFORMATION The Hlo is not intended to replce regulr pressure-checks nd tire mintennce prctices s specified y the FMCSA in their
More informationSSAB Water mains PIPES AND FITTINGS
SSAB Wter mins PIPES AND FITTINGS Pipes nd fittings mnufctured y SSAB re used primrily with wter pipeline sizes DN 400-1200. The fittings re mde of steel pressure pipes (ex works delivery) nd cn e coted
More informationFUEL SYSTEM. Table of Contents. Section 3B - Carburetors
Tle of Contents FUEL SYSTEM Section 3B - Cruretors CARBURETORS Fuel System - Trouleshooting.............. 3B-2 Generl Informtion.................... 3B-2 Attenutor And Cr Throttle Levers......... 3B-4
More informationALLROUNDER 1200 T. Table diameter: 1200 mm Clamping force: 800, 1000, 1600, 2000 kn Injection unit (acc. to EUROMAP): 70, 100, 170, 290, 400, 800
Fcts nd figures ALLROUNDER 12 T Tble dimeter: 12 mm Clmping force: 8, 1, 16, 2 kn (cc. to EUROMAP): 7, 1, 17, 29, 4, 8 www.rburg.com 12 T Mchine dimensions up to 1 kn 385 1) 323 2) 3545 3) 366 4) 391 5)
More information4/2- and 4/3-way shut-off valve
Courtesy of CMA/Flodyne/Hydrdyne Motion Control Hydrulic Pneumtic Electricl Mechnicl (00) 426-540 www.cmfh.com 4/2- nd 4/3-wy shut-off vlve Type Z4WE Size 6 Component series 3X Mximum operting pressure
More informationHot Air Thermostats. WTHc series. Special features. Brief description. Switching function. Approval/approval marks (see "Technical data")
Delivery ddress: Mckenrodtstrße 36039 Fuld, Germny Postl ddress: 36035 Fuld, Germny Phone: +9 66 6003-0 Fx: +9 66 6003-607 E-mil: mil@jumo.net Temple Bnk, Riverwy Hrlow, Essex CM0 DY, UK Phone: + 79 635533
More informationPOWER TRIM. Table of Contents. Section 5B - Trim Cylinders
SERVICE MANUAL NUMBER 14 Tle of Contents POWER TRIM Setion 5B - Trim Cylinders TRIM CYLINDERS Speifitions....................... 5B-2 Torque Speifitions............. 5B-2 Speil Tools.....................
More informationEXTERIOR GROUP CONTENTS FRONT BUMPER ASSEMBLY REAR WIPER AND WASHER REAR BUMPER ASSEMBLY
5- GROUP 5 CONTENTS FRONT BUMPER SSEMBLY..... 5- SPECIL TOOL..................... 5- REMOVL ND INSTLLTION........ 5- DISSSEMBLY ND RESSEMBLY..... 5- RER BUMPER SSEMBLY...... 5-6 SPECIL TOOL.....................
More information