SpaceStation TM. Installation Instructions SpaceStation Occupancy Lighting Control System. Please Save These Instructions

Transcription

1 Phone: concealte.com! Installaton SpaceStaton Occupancy Lghtng Control System Please Save These Important Safeguards Read and Follow All Safety þdo not use outdoors. þdo not let power supply cords touch hot surfaces. þdo not mount unts where they wll be eposed to drect sunlght, radators, gas or electrc heaters. Prolonged eposure to temperatures eceedng 95 degrees Fahrenhet may reduce battery lfe and vod warranty. þequpment should be mounted securely n locatons and at heghts where t wll not be readly subjected to tamperng by unauthorzed personnel. þthe use of accessory equpment not recommended by the MANUFACTURER may cause an unsafe condton. þthe AC voltage ratng of ths equpment s specfed on the product label. Do not connect equpment to any other voltage. þdo not use ths equpment for other than ts ntended purpose. þservcng of ths equpment should be performed by qualfed servce personnel. TECHNICAL DATA Model: SS Seres 2000 Ac Supply Voltage: 120/277 Volts (+/- 10%) Mamum Load: 120v/400w Ballast or 800w Tungsten, 277v/1200w Mamum Ballast Load Operatng Voltage: 50/60hz, v +/- 10% Swtched Power: 800/1200w Standby Power: 0.6w (standby), 1.2w (operaton) 10 / 30 / 50 / %, Can Be Customzed Hold Tme: 5s / 30s / 180s /300s /15mn / 25mn, Can Be Customzed Daylght Threshold OPTIONAL: 20FC - 300FC Daylght / Twlght / Darkness, Can Be Customzed Sensor Prncple: Mcrowave Moton Detector Mcrowave Frequency: 5.8 Ghz +/- 75mhz Mcrowave Power: <1mw Detecton Range: Ma. (0 X H): 8m X 10m Detecton Angle: Mountng Heght: m Operatng Temperature: -35 c `- +70 c IP Ratng: IP 20 (mountng nsde a lamp); IP 65 (mountng n specal bo) Certfcatons: SpaceStaton Inde Seres: SS Seres Important Safeguards 2 Sensor Mountng 3 Sensor Adjustments 4 New Constructon/Retroft 5 Sngle Wrng 6 Multple Wrng 7 Adjustable Remote Mountng (ARM) 8 Troubleshootng Lmted Warranty GREENTECHNOLOGY SpaceStaton sensors can be confgured to operate wth any number of sensors and control any number of lghtng crcuts as one system for any szed room applcaton. All Concealte ftures are tested and are guaranteed to be free from defectve materals and workmanshp for a perod of three years from date of shpment under normal operatons and proper use. Correcton of all defects shall be by replacement or repar (at our dscreton) and shall consttute fulfllment of all manufacturer's oblgatons. We wll not allow any charge for labor, materals, etc. that does not have our wrtten approval before the work s begun. Damage ncurrng n handlng or n transt are not covered by ths guarantee. Any other warranty, epressed or mpled, s hereby vod. Modfcatons to the product or falure to follow nstallaton nstructons wll vod the warranty. Copyrght Concealte Lfe Safety Products. All Rghts Reserved. Specfcatons Subject to Change.

2 INSTALLATION Sensor Mountng SpaceStaton IMPORTANT: LOCATE SENSOR IN THE CENTER OF THE ROOM WARNING: to avod fre, shock/electrocuton, or njury TURN OFF POWER at crcut breaker or fuse and test to ensure that power s off before wrng. Remove and dscard the packagng materals. Falure to follow publshed nstallaton nstructons or any modfcatons to the product may damage the unt and wll vod the warranty. ROOM WIDTH Area Senstvty Adjustment (SpaceStaton Centered n Room) Note: Mamum 60' Heght Provdes Mamum Range Coverage to Feet Celng Heght Room Area Range Coverage at Senstvty % Settng 10% 35% 50% 75% 100% ROOM LENGTH 8 Feet 10 Feet 7' 7' 8' 8' 10' 10' 13' 13' 12' 12' 17' 17' 20' 20' 22' 22' Adjustable Range Control Panels (RCP) controls eact cut off range of each room 12 Feet 8' 8' 12' 12' 20' 20' 25' 25' Step 1: Sensor Mountng A. Determne mountng locaton wthn room or area to be covered. Center the sensor wthn the center of the room/area when possble. Loosen front knobs. Loosen Front Knobs to Slde Panels B. Slde to adjust the four (4) room control panels to the dstance ndcated to match the dstance n feet between the sensor and each of the room wall (to allow actvaton from any movement wthn that room area). Slde All Four Panels to the Match the Dstance n Feet Between Sensor and Room Walls 2

3 SpaceStaton INSTALLATION Sensor Adjustments WARNING: to avod fre, shock/electrocuton, or njury TURN OFF POWER at crcut breaker or fuse and test to ensure that power s off before wrng. Remove and dscard the packagng materals. Falure to follow publshed nstallaton nstructons or any modfcatons to the product may damage the unt and wll vod the warranty. STEP 2: SENSOR ADJUSENTS A. Detecton Area Detecton are can be reduced by selectng the combnaton on the DIP swtches to ft precsely for each specfc applcaton. B. Hold Tme Hold-tme means the tme perod you would lke to keep the lamp on after the person has left the detected area. Sensor Adjustments C. Daylght Sensor (Remote Opton Only) The sensor contans a daylght sensor n order to allow a functon only below a defned brghtness threshold. DETECTION AREA HOLD TIME DAYLIGHT SENSOR I II III IV V 100% 75% 50% 30% 10% I II III IV V VI 5 S 30 S 180 S 300 S 15 MIN 25 MIN I II III IV V 2O FC 5O FC 200 FC 300 FC DISABLE BRIGHTNESS THRESHOLD SETUP DAYLIGHT: The lamp works always, even durng daylght. Note: Three swtches should be put n OFF poston when remote day lght sensor s not nstalled. ON ON ON 3

4 SpaceStaton INSTALLATION New Constructon & Retroft WARNING: to avod fre, shock/electrocuton, or njury TURN OFF POWER at crcut breaker or fuse and test to ensure that power s off before wrng. Remove and dscard the packagng materals. Falure to follow publshed nstallaton nstructons or any modfcatons to the product may damage the unt and wll vod the warranty. Accessble Celng Installaton: T-Bar Opton - Suspended Accessble Celngs Note: Use optonal T-bar bracket for support mountng to nverted T-grd lay n suspended celngs. Inccessble Celng Installaton: ARM Opton - Gypsum Board and Other Inaccessble Celngs Note: Use Optonal arm bracket for support mountng to structural blockng or stud also for retroft nstallaton through estng celng hole (see page 8 also). ARM Adjustable Remote Mountng to structural / blockng to secure SpaceStaton 4

5 Power Connectons INSTALLATION Sngle Wrng Control Wrng Dagram WARNING: to avod fre, shock/electrocuton, or njury TURN OFF POWER at crcut breaker or fuse and test to ensure that power s off before wrng. Remove and dscard the packagng materals. Falure to follow publshed nstallaton nstructons or any modfcatons to the product may damage the unt and wll vod the warranty. STEP #3: Provde Power Connectons Branch crcut: buldng power only connectons. Provde 120 VAC or 277 VAC unnterrupted power connectons to termnate wthn the celng mounted bracket juncton bo. Sngle Lghtng Crcut Control Wrng Dagram Lne Input Black Neutral Load Output Blue Load Red Neutral Whte Black - Lne Input Whte - Neutral Red - Lne Output to Load A Optonal B Optonal C Load Informaton A Opton (OR) Optonal: Overrde FDP Concealed Wall Swtch Lne Black Yellow B Opton (RDS) Optonal: Remote Daylght Sensor SpaceStaton Occupancy Sensor C Load Load must not eceed VAC. Load must not eceed VAC. Loads n ecess must use the Command Module opton for hgher wattage. Note: Dmmng ballast crcuts must be controlled by the Command Module opton. 5

6 Power Connectons INSTALLATION Multple Wrng Control Wrng Dagram WARNING: to avod fre, shock/electrocuton, or njury TURN OFF POWER at crcut breaker or fuse and test to ensure that power s off before wrng. Remove and dscard the packagng materals. Falure to follow publshed nstallaton nstructons or any modfcatons to the product may damage the unt and wll vod the warranty. Multple Lghtng Crcut Control Wrng Dagram *Requred for two or more crcuts A Optonal B Optonal C Load Informaton D Command Module Informaton Lne Input Neutral A Opton (OR) Optonal: Overrde FDP Concealed Wall Swtch Load Output Red Neutral Whte Lne Black Specfed: # of 20 AMP Crcuts SpaceStaton Occupancy Sensor D Blue Yellow C Load B Command Module (CM) # of poles.e. CM04-4 lghtng crcut poles Opton (RDS) Optonal: Remote Daylght Sensor Load must not eceed VAC. Load must not eceed VAC. Loads n ecess must use the Command Module opton for hgher wattage. ATTENTION! Verfy lne voltage s compatble wth electrcally held col voltage (120 VAC or 277 VAC) Dmmng ballast crcuts must be controlled by the Command Module opton. TWO OR MORE SENSORS OPERATING TOGETHER Parallel connect multple (two or more) sensors for areas eceedng range coverage of one lghtng sensor. Neutral Whte 6

7 Power Connectons INSTALLATION Adjustable Remote Mountng (ARM) WARNING: to avod fre, shock/electrocuton, or njury TURN OFF POWER at crcut breaker or fuse and test to ensure that power s off before wrng. Remove and dscard the packagng materals. Falure to follow publshed nstallaton nstructons or any modfcatons to the product may damage the unt and wll vod the warranty. ARM Adjustable Remote Mountng Provde fleble condut connectons to estng Lghtng Branch Crcut Estng Celng Openng The mnmum sze openng s 4 nches n dameter for nserton of SpaceStaton nto an naccessble celng openng ARM Adjustable Remote Mountng to structural / blockng to secure SpaceStaton Lghtng Branch Crcut Lghtng Branch Crcut Space Staton Sensor Estng Celng Estng Lght Fture, J Bo or Access panel Note: Dmmng ballast crcuts must be controlled by the Command Module opton. 7

8 Troubleshootng Troubleshootng Tme Delay IMPORTANT START-UP INFORMATION The frst tme the sensor s powered-up the load wll flash ON then OFF once, then there wll be 10 seconds whle the sensor warms-up. The SpaceStaton automatcally turns OFF the load after the coverage area has been vacant for the amount of tme set n the tme delay. The mnmum settng s 10 seconds, mamum s 30 mnutes. TROUBLESHOOTING Quck Test: Turn the tme delay to mnmum. Move out of the sensor's vew. Lghts should turn OFF after 10 seconds. Move nto the sensor's vew. The lghts should turn ON. Lghts do not turn OFF: 1. If there s no moton n the set coverage area, reduce the senstvty varyng room panel adjusted postons. 2. Verfy room panel adjustment postons. 3. Verfy tme delay and that there s no movement wthn the sensor's vew for that tme perod. FCC NOTICE FCC ID: IXIIII Ths devce comples wth part 15 of the FCC Rules, Operaton s subject to the followng two condtons: (1) Ths devce may not cause harmful nterference, and (2) ths devce must accept any nterference receved, ncludng nterference that may cause undesred operaton. Warranty All Concealte ftures are tested and are guaranteed to be free from defectve materals and workmanshp for a perod of three years from date of shpment under normal operatons and proper use. Correcton of all defects shall be by replacement or repar (at our opton) and shall consttute fulfllment of all manufacturer's oblgatons. We wll not allow any charge for labor, materals, etc that does not have our wrtten approval before the work s begun. Damage ncurrng n handlng or n transt are not covered by ths guarantee. Any other warranty, epressed or mpled, s hereby vod. Modfcatons or changes to the product or falure to follow nstallaton nstructons wll vod the warranty. 8