PARTS MANUAL SECTION 93

Transcription

1 Published 12/14 RMB1865 RMB RMB1865E RMB1865E-1 HYDRAULIC BOOM CUTTER PARTS MANUAL SECTION 93 An Operator s Manual was shipped with the equipment. The Operator s Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator s Manual is not with the equipment, contact your dealer or Bush Hog to obtain a copy before operating the equipment. Important Operating and Safety Instructions are found in the Mower Safety Video that can be instantly accessed on the internet at:

2 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. For maximum safety and to guarantee optimum product reliability, always use genuine BUSH HOG Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.direct any questions regarding parts to: BUSH HOG 2501 Griffin Ave. Selma, AL Contact Us Alamo Group Inc.

3 To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty RegistrationForm in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on thewarranty Card and on the Warranty Form that you retain.

4 LIMITED WARRANTY Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state and municipalities use and ninety (90) days for commercial use from date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective parts. Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hog dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship. DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES Bush Hog s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale or use of the items warranted. Such incidental and consequential damages shall include but not be limited to: transportation charges other than normal freight charges; cost of installation other than cost approved by Bush Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond the control of Bush Hog. THIS LIMITED WARRANTY SHALL NOT APPLY: 1. To vendor items which carry their own warranties, such as engines, tires, and tubes. 2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. 3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability. 4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in the sole judgement of Bush Hog, affects its performance, stability or reliability. 5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure. 6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the company s sole judgement is a wear item. NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN WRITING AND SIGNED BY BUSH HOG S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA Record the model number, serial number and date purchased. This information will be helpful to your dealer if parts or service are required. MAKE CERTAIN THE WARRANTY HAS BEEN FILED WITH BUSH HOG SELMA, ALABAMA MODEL NUMBER SERIAL NUMBER DATE OF RETAIL SALE

5 November, 2014 ALPHABETICAL INDEX RMB1865/1865E, RMB1865-1/1865E-1 BOOM MOWER ITEM PAGE NUMBER 100 LPM DRIVE MODULE - SUPERCUT AND MULTICUT BEARING UNIT MODULE - ROTARY HEAD BLADE BAR ASSEMBLY - ROTARY HEAD BRACKET MODULE - ROTARY HEAD CAB CONTROL MOUNT CABLE ARMHEAD CONTROL VALVE W/O QUICK RELEASE CABLES (RMB1865, RMB1865E) , CABLE ARMHEAD CONTROL VALVE WITH QUICK RELEASE CABLES (RMB1865-1) , CABLE ROTOR CONTROL VALVE W/O QUICK RELEASE CABLES (RMB1865, RMB1865E) CABLE ROTOR CONTROL VALVE WITH QUICK RELEASE CABLES (RMB1865-1, RMB1865E-1) CASING - SUPERCUT FLAILHEAD CASING MODULE- ROTARY HEAD DIPPER ARM DECAL KIT - ROTARY HEAD FILTER AND DIFFUSER ASSEMBLY , FLAIL HEAD - MULTICUT FLAIL HEAD - SUPERCUT (47 WIDE) FRONT FLAP KIT, SUPERCUT AND MULTICUT GEARBOX ASSEMBLY - PARTS (BIMA) (RMB1865, RMB1865E) , GEARBOX ASSEMBLY - PARTS (COMER) (RMB1865-1, RMB1865E-1) GUARD KIT HEAD, ANGLING HOSE KIT - RMB1865, RMB HOSE KIT - RMB1865E, RMB1865E , HYDRAULIC CYLINDER - ANGLE HYDRAULIC CYLINDER - LIFT HYDRAULIC CYLINDER - REACH HYDRAULIC CYLINDER - SLEW HYDRAULIC HOSES AND FITTINGS , HYDRAULICS MODULE - ROTARY HEAD HYDRAULIC TANK , LIFT FLOAT KIT , LIGHT KIT (OPTIONAL FOR RMB1865 & RMB1865E ONLY) LIGHT KIT (STANDARD FO RMB & RMB1865E-1 ONLY) MAIN ARM MAIN FRAME , MANIFOLD ASSEMBLY - RMB1865E, RMB1865E MANIFOLD ADAPTOR KIT - RMB1865E, RMB1865E MOTOR COVER - MULTICUT MOTOR COVER 1.2M SUPERCUT MOTOR MODULE - ROTARY HEAD PILLAR, RH , PUMP AND GEARBOX ASSEMBLY (BIMA) (RMB1865, RMB1865E) , PUMP AND GEARBOX ASSEMBLY (COMER) (RMB1865-1, RMB1865E-1) PUMP ASSEMBLY QUAD DRIVE MODULE - MULTICUT ROLLER 1.2 SUPERCUT ROLLER ASSEMBLY - MULTICUT ROTOR MODULE - MULTICUT ROTOR MODULE - SUPERCUT SAFETY DECALS (BOOM) (RMB1865, RMB1865E) SAFETY DECALS (BOOM) (RMB1865-1, RMB1865E-1) SAFETY DECALS (CUTTER HEAD) SHEARTRIM SICKLEBAR (59 WIDE) SHIELDING , SKID KIT - MULTICUT SKID KIT - SUPERCUT STABILIZER STOP ASSEMBLY - ROTARY HEAD SOLENOID KIT - RMB1865E, RMB1865E SWITCH BOX ASSY. - RMB1865E, RMB1865E-1 (Used on Models with Serial No s before M ) SWITCH BOX ASSY. - RMB1865E-1 (Used on Models starting with Serial No. M & Above) SWITCH BOX PARTS - RMB1865E-1 (Used on Models starting with Serial No. M & Above) VALVE ASSEMBLY - RMB1865E, RMB1865E

6

7 SAFETY DECALS (BOOM) (RMB1865, RMB1865E) November, 2014 REF. NO. PART NO. DESCRIPTION QTY. 1 D433 Decal, Multi Hazard 1 2 D388 Decal, Driveline Hazard 1 3 D355 Decal, Important Sway Bars 1 4 D623 Decal, Warning Pinch Point 6 5 D628 Decal, Danger Crushing Hazard 1 6 D617 Decal, Warning Oil Leak 1 7 D354 Decal, Danger Crushing Hazard Decal, Bush Hog Logo, Decal, Model No Decal, Bush Hog Logo, D524 Booklet, Safety Reflector, SMV Triangle 1

8 SAFETY DECALS (BOOM) (RMB1865-1, RMB1865E-1) Novermber, 2014 REF. NO. PART NO. DESCRIPTION QTY. 1 D628 Decal, Multi Hazard 1 2 D617 Decal, Driveline Hazard Decal, Important Sway Bars 1 4 D547 Decal, Warning Pinch Point 6 5 D623 Decal, Danger Crushing Hazard Decal, Warning Oil Leak Decal, Danger Crushing Hazard Decal, Danger, Auto Break Away Decal, Grease Point - Base Unit Decal, Bush Hog Logo, Decal, Bush Hog Logo, Decal, Model No Reflector, SMV Triangle 1

9 SAFETY DECALS (CUTTER HEAD) December, 2014 REF. NO. PART NO. DESCRIPTION QTY Decal, Bush Hog Logo, D626 Decal, Deflector Warning Decal, Warning Thrown Objects Decal, Instruction Decal, Instruction Multi Reflector, Red Reflector, Yellow Decal, Instruction Grease

10 STABILIZER November, 2014 REF. NO. PART NO. DESCRIPTION QTY Linch Pin, Med. 7/ PTO Hook Support-Plated Top Link Assy To 517mm Plastic Insert 45mm Dia Sleeve HFS Tube 38.6 x 6.3 Wal Quadrant Pin-Stabilizer Narrow Nose Stabilizer W.A Spacer 55 x 40.5 x Spacer Sleeve Hose Tie Lg C Stabilizer Tongue Cat. 3-Cast Pin-Top Link Flatwasher M Flatwasher M24 BZP Nyloc Nut M Nyloc Nut M Bolt Capscrew M24 x Roll Pin M5 x

11 MAIN ARM November, 2014 REF. NO. PART NO. DESCRIPTION QTY Grease Nipple, 1/ Hose Guard W.A Lift Base Pin W/Assy Main Arm RMB1865/RMB1865E Clamp, Lower Hose Bushing 40 x 44 x " BSP Pair Hose Clamps Flatwasher, 10.5 x 23.5 x Washer, M8 External Shakeproof Nut M10 Nyloc Capscrew M10 x Capscrew M x Capscrew M8 x 90 BZP

12 DIPPER ARM November, 2013 REF. NO. PART NO. DESCRIPTION QTY Bushing 37 x 30 x Grease Nipple, 1/ Hose Guard W/A Black Pin W/A Dipper Ram RH Dipper Arm W.A Pin W/A - T/Link Outer Main Pivot Pin Clamp, Hose Bushing, Flail Head Flatwasher, 10.5 x 23.5 x Lockwasher 12mm Washer, M8 External Shakeproof Nut M10 Nyloc Capscrew M12-P1.75 x 65mm Capscrew M10 x Capscrew M8 x 75 Lg BZP Capscrew M10-P1.50 x 25mm Edging Strip - 160mm Lg Seal, Lip 30 x 40 x

13 HEAD, ANGLING November, Spring Dowel 5/8 in x 3-1/2 in Flat Washer 30mm - Plated Bushing 37 x 30 x Grease Nipple, 1/ Radius Arm Radius Arm Slave Link Casting C Jaw Plt Cast 30.0 Pivots Pivot Tube Pin Pin - 30mm x 116 Lg Hose Brkt 1-5/16 JIC Hose Tray Nut Flatwasher 10.5 x 23.5 x Nut M10 Nyloc Bolt Ht M16 x 1.5P x 55 Lg Bolt Bolt M10 x Capscrew M10-P1.5 x 30mm Pl Capscrew M10-P1.50 x 35mm Roll Pin M5 x Roll Pin M6 x Seal, 30 x 40 x

14 PILLAR, RH November,

15 PILLAR, RH November, Grease Nipple, 1/ RH Pillar Pin W/A - Slew Rod Pin W/A - Left Ram Base Main Pivot Pin Pivot Pin Thrust Washer 75 x 41 x Screw, Special M12 x 40 Drilled Lockwasher, 12mm Nut M10 Nyloc Nut Nyloc M Capscrew M12-P mm Capscrew M10-P mm Capscrew M12-P mm Cotter Pin 4mm x 25mm

16 MAINFRAME November,

17 MAINFRAME November, Pin, Cotter Linch Pin, Med. 7/ Grease Nipple, 1/ Linkage Pin Cat Spacer, 15 Lg Spacer, 10 Lg RH Mainframe Pin Plug, Plastic, Square Stand Leg LH Stand Leg RH Leg Pin Bushing 40 x 44 x 40 Glacier Driveline, 27 Pin Ctrs Nut M 20 - P Nut M10 Nyloc Capscrew M10-P mm Capscrew M20 x 55 (Coarse) H.T

18 SHIELDING November,

19 SHIELDING November, Pop Rivet Dia 4.8 x 16 Lg Sponge Pad RH Cover & Valve Mtg RH Rear Cover W.A Tank Top Cover RH Valve Cover Blanking Plate-Rear Cover Overcentre Fastener Hook-Small Flatwasher, 10.5 x 23.5 x Lockwasher, 10mm Dia. BZP Taptite M6 x Capscrew M10-P mm Foam Strip 275mm Lg Foam Strip 410mm Lg Short Nose, Slotted Head Size Fast Turn Size 8 Slip On Fast Turn Plastic Retainer

20 HYDRAULIC TANK April,

21 HYDRAULIC TANK November, Adaptor 1" x 1-1/4" BSP Pop Rivet Dia 4.8 x 16 Lg Tank W.A.-RH PA47, PA50 & ECO Rivet Washer-For 4.8 Dia Rivet Plastic Manual Holder Us Gauge, Level Asy, Filler Breather UCP AB Filter Assy Incl Diffuser Suction Stranier 125 Micron Adp.Hyd. 1-1/4 BSP x 1-1/2 BSP /4 BSP Bonded Seal Spring Washer 8mm M16 Nyloc Nut Capscrew M8 x 30 (Coarse) Capscrew M16 x 45 Coarse H.T O Ring

22 FILTER AND DIFFUSER ASSEMBLY November,

23 FILTER AND DIFFUSER ASSEMBLY November, Filter Element Filter Lid Spring Fitler Housing Seal O-Ring O-Ring Filler Cap Moulded Seal For Plastic Filter Housing

24 HYDRAULIC HOSES AND FITTINGS November,

25 HYDRAULIC HOSES AND FITTINGS November, Hydraulic Cylinder Assy -Slew Hydraulic Cylinder Assy -Reach Hydraulic Cylinder Assy - Lift Hydraulic Cylinder Assy - Angle Adapter mm 1 5/16"-12 JIC Hose Clips 40-55mm *BI* Hose Sleeving FC Lg Hose Sleeving FC Lg Hose Sleeving FC Lg Bore Suction Hose 1 1/2" - 470mm Long Elbow 1" BSP M-Fln 90 Swept Blanking Cap 1-5/16" JIC Swivel Adp. 1 BSP-F x 1-5/16-M Hose Tie Lg (Not Shown) Hose Tie Lg (Not Shown)

26 HYDRAULIC CYLINDER - SLEW December, Slew Ram JIC Assy P Slew Ram Assy-Painted Kit, Seal, Slew Ram Bushing, Plastic 42 x 35 x Seal, 3/8 BSP Bonded Adaptor Restrictor 3/8 BSP-9/16 JIC Valve, Ball /8 BSP Double Male Union,Swivel 3/8 BSP M-F

27 HYDRAULIC CYLINDER - REACH December, Reach Ram Leopard 1046 JIC P Hydraulic Cylinder Assy-Painted Kit, Seal Bushing, Plastic 42 x 35 x Adaptor Seal, 3/8 BSP Bonded

28 HYDRAULIC CYLINDER - LIFT December, Assy, Lift Ram 90 x 40 x 475 JIC P Hydraulic Cylinder Assy - Lift Kit, Seal, Lift Cylinder Bushing, Plastic 42 x 35 x Adapter Double Male 3/8 BSP Adaptor Seal, 3/8 BSP Bonded Union, Swivel 3/8 BSP M-F Valve, Ball

29 HYDRAULIC CYLINDER - ANGLE December, Angle Ram Assy PA52/59 JIC P Hydraulic Cylinder Assy - Angle Kit, Seal, Angle Ram Adaptor Seal, 3/8 BSP Bonded Bushing 37 x 30 x Grease Nipple, 1/ Seal, Lip 30 x 40 x

30 December, 2014 PUMP AND GEARBOX ASSEMBLY - BIMA (RMB1865, RMB1865E) (Used on Models with Serial Number M and Below)

31 December, 2014 PUMP AND GEARBOX ASSEMBLY - BIMA (RMB1865, RMB1865E) (Used on Models with Serial Number M and Below) Gearbox 4.25:1 13T, Bima Pump, Tandem Iron Pressure Connection Kit Flange-Pump Port 1/2" BSP Capscrew M10 x 40 (Coarse) H.T Socket Capscrew M8 x O-Ring 2 ID x 2-1/4 OD O-Ring 1-1/16 ID x 1-1/4 OD Lockwasher, 10mm Dia Flatwasher, 10.5 x 23.5 x Capscrew M12 x 60 Skt Seal, 1/2 BSP Bonded Seal, 3/4 BSP Bonded Block Suction Taper Adaptor 1-1/4" BSPT x 1-1/2" L.P Adapter St 3/4 JIC-M x 1/2 BSP-M Adapter 16 M JIC - 12 M BSPP

32 December, 2014 GEARBOX ASSEMBLY - PARTS (BIMA) (RMB1865, RMB1865E) (Used on Models with Serial Number M and Below)

33 November, 2014 GEARBOX ASSEMBLY - PARTS (BIMA) (RMB1865, RMB1865E) (Used on Models with Serial Number M and Below) Cap-80mm Dia Internal Circlip 80mm Dia Bearing Gearbox Casting Drain Plug Shaft Driveshaft Key Shaft Seal Internal Circlip 90mm Dia Bearing Larger Input Shaft Primary Gear Level Plug Gearbox Cover Setscrew Breather 1/2" BSP Sealing Washer Oil Plug Ring Oil Plug Cap-90mm Dia Oil Plug Gearbox Seal

34 December, 2014 PUMP AND GEARBOX ASSEMBLY - COMER (RMB1865-1, RMB1865E-1) (Used on Models with Serial Number Above M ) Comer Gearbox Group 2/3 13T 1: Pump, Iron TI Pressure Connection Kit Flange-Pump Port 1/2" BSP Capscrew M10 x 40 (Coarse) H.T Socket Capscrew M8 x O-Ring 2 ID x 2-1/4 OD O-Ring 1-1/16 ID x 1-1/4 OD Setscrew, M12 x Lockwasher, 10mm Dia Flatwasher, 10.5 x 23.5 x Lockwasher, 12MM Capscrew M12 x 60 Skt Seal, 1/2 BSP Bonded Seal, 3/4 BSP Bonded Block Suction Taper Adaptor 1-1/4" BSPT x 1-1/2" L.P Comer Gearbox Decal Adapter St 3/4 JIC-M x 1/2 BSP-M Adapter 16 M JIC - 12 M BSPP

35 December, 2014 GEARBOX ASSEMBLY - PARTS (COMER) (RMB1865-1, RMB1865E-1) (Used on Models with Serial Number Above M ) Casing Cover Plug, 3/ Bolt, M8 x 18, Cap, 26 x Cap, 80 x Ball Bearing, Snap Ring, 90 UNI Key, Parallel, B16 x 10 x Oil Seal, 40 x 90 x 8/ Shim, 61.7 x Gear, Z51 M Cap, 90 x Input Shaft Pinion, Z17 M Spacer Connector, 3/8 Male/Male Plug, Oil Level Ind Window, 3/ Filler Plug Elbow, 90 Deg

36 PUMP ASSEMBLY November, 2013 PART DESCRIPTION QTY. NO Tandem Pump Assy Pump (Front Half Of ) Seal Kit For Pump Rear Pump For For Unts Parker Male Male Coupling For

37 HOSE KIT - RMB1865, RMB November, Hose 1 Bore x 500 JIC 90 XST Hose 1-5/16" JIC FS/F mm Lg Hose 1-5/16" JIC FS/F Lg Hos Hose 1 Bore x 3700mm Hose 3/4" JIC FS/F90 x Hose 7/8" JIC FS/F90 550mm Lg Hose 9/16" JIC Fs/Fs 2100mm Lg Hose 9/16 JIC FS/F mm Lg Hose 9/16 JIC FS/F mm Lg Hose 1/4 Bore x 1200mm Hose 9/16" FS/FS 1200 Lg Hose 9/16" JIC FS/F Lg

38 HOSE KIT - RMB1865E, RMB1865E-1 November,

39 HOSE KIT - RMB1865E, RMB1865E-1 November, 2014 QTY. NO. NO. DESCRIPTION REQ D Hose, 1 Bore x 500 JIC 90 XST /16" JIC FS/F90 550mm Lg /16" JIC FS/F Lg Hos /16" JIC FS/F Lg Hose 3/8 Bore x 500mm Hose Hose 9/16" JIC FS/FS 1900 Lg Hose, 1/4 Bore x 6500 STX 90 JIC Hose Hose Hose /4 Bore Hose

40 VALVE ASSEMBLY - RMB1865E, RMB1865E-1 November, 2014 QTY. NO. NO. DESCRIPTION REQ D Valve Mtg Plate Manifold Assy Adaptor Kit Solenoid Kit Valve Flatwasher, 10.5 x 23.5 x Lockwasher, 10mm Dia Nyloc Nut M Capscrew M10 - P1.5-30mm

41 MANIFOLD ASSEMBLY - RMB1865E, RMB1865E-1 November, 2014 QTY. NO. NO. DESCRIPTION REQ D Float Valve Block Bridging Plate Relief Valve Cap Check Valve Cap Actuator Check Valve Blanking Plate Slew Block Block - Manifold Assy 1 QTY. NO. NO. DESCRIPTION REQ D Pipe Plug - Gas 1/ Pipe Plug - Gas 1/ Taper Plug Seal - 3/ O-Ring 9mm x 12.2mm O-Ring 18mm x 22mm x Ring, Anti Extrusion Sckt Hd Screw M5 x SHCS M9-PO.84MPL 9 19 G Relief Valve 190 BAR

42 ADAPTOR KIT ASSEMBLY - RMB1865E, RMB November, 2014 QTY. NO. NO. DESCRIPTION REQ D Adaptor Hyd 3/8 BSP-M x 7/8 JIC Union, 3/8 BSP Coned - 3/4 JIC Spring.275 x 23 SWG x 5/ Restrictor Disc, 1.5MM Orifice Restrictor Disc, 1.8MM Orifice Restrictor Union, 1/4BSPM x 1/4BSPM x Restrictor Union, 1/4BSPM x 1/4BSPM x Restrictor 9/16 JICM x 1/4 BSP Restrictor 9/16 JICM x 1/4 BSP Adaptor 1/4 BSP x 9/16 JIC Adaptor, Special 1/4BSP x 3/8 BSP Seal 1/4 BSP Seal 3/8 BSP Adaptor 1/4 BSP x 9/16 JICM

43 November, 2014 SWITCH BOX - RMB1865E, RMB1865E-1 (Used on Models with Serial Numbers before M ) QTY. NO. NO. DESCRIPTION REQ D XTC Control Module Decal 1 SOLENOID KIT - RMB1865E, RMB1865E-1 QTY. NO. NO. DESCRIPTION REQ D Solenoid Prop Plug In Loom Direct Valve, Single Solenoid Solenoid Valve, Single Valve, Double Solenoid Loom - Angle Float Capscrew M5 x Capscrew M5 x

44 December, 2014 XTC CONTROLS 7 SERVICE MODULE - RMB1865E-1 (Used on Models starting with Serial Number M and Above) XTC Controls 7 Service V4 Arm Rest Foam XTC 7 Service Module Mount XTC Arm Rest w/assy Screw, Self Tapping, 12 x 1/ XTC Mounting Plate Capscrew, M5 x Spring Washer, M Operations Decal, XTC 7 Service XTC Decal Mounting Plate Capscrew, M5 x Nut, Nylock, M Cable Tie, 180MM Lg

45 December, 2014 XTC CONTROLS 7 SERVICE - RMB1865E-1 (Used on Models starting with Serial Number M and Above) XTC Enclosure 7 Service XTC 7 Service Keypad Switch E/Stop Otto Thumb Wheel w/tab JC2000 w/plain Grip Gland, M16 Plastic Connector - 1 Fuse /4 Turn Fastener, Pk of Way Connector ITT (Not Shown) Gore Breather Loom Power Supply (Not Shown)

46 November, 2014 CABLE ROTOR CONTROL VALVE ASSEMBLY WITHOUT QUICK RELEASE CABLE (RMB1865, RMB1865E) Valve, Rotor Control (190 Bar) Seal, 3/4 BSP Bonded Capscrew M10-P1.5-40mm PL Nut M10 Nyloc Control Hd/Cable Assy-3.5m Extension Adapter 3/4" BSP M-F Capscrew M6 x 55 (Coarse) H.T Nut M6 Nyloc Control Cable Brkt Capscrew M 8-P1.25 x 16mm Nut 8mm-P1.25 PL Adapter 3/4 M BSP-7/8 M JIC Adapter 16 M JIC - 12 M BSPP

47 November, 2014 CABLE ROTOR CONTROL VALVE ASSEMBLY WITH QUICK RELEASE CABLE (RMB1865-1, RMB1865E-1) Valve, Rotor Control (190 Bar) Seal, 3/4 BSP Bonded Capscrew M10-P1.5-40mm PL Bolt M65 x Locknut M10, Nyloc Locknut M6, Nyloc Control Head RCV Cable RCV Capscrew M16 x Control Cable Bracket Setscrew M8 x Nut 8mm-P1.25 PL Adapter 3/4 M BSP-7/8 M JIC Adapter 16 M JIC - 12 M JIC Extension Adaptor 3/4 JIC

48 November, 2014 CABLE ARMHEAD CONTROL VALVE WITHOUT QUICK RELEASE CABLES (RMB1865, RMB1865E)

49 November, 2014 CABLE ARMHEAD CONTROL VALVE WITHOUT QUICK RELEASE CABLES (RMB1865, RMB1865E) Control Valve 4 Spool Relief Valve Cartridge Spring.275 x 23 Swg x 5/8 Lg Relief Valve Housing Body, Relief Valve Seal, 3/8 BSP Bonded Seal, 1/2 BSP Bonded Control Hd/Cable Assy-3.5m Seal, 1/4 BSP Bonded Restrictor 1/4-3/8 BSP Adaptor 3/8 BSP M/M Adaptor 1/2 x 3/8 BSP M/M Adaptor, 1/4 x 3/8 BSP Male Tee Adaptor 1/4 BSP M-F-M Stud M6 x 233 Plated Arm Rest Brkt W/A Decal, Control Decal-Slew SMA Union 3/8 BSPM x 3/8 BSPM Restrictor Adaptor 1/4" BSP Restrictor Disc, 1.8mm Orifice Shcs Metric 5-P0.8-12mm PL Bolt Nut Nyloc M Capscrew M8-P mm Nut 8mm-P1.25 PL Tee 1/2-1/2-1/4 Fmm Connector, 3/8 BSP 90 Deg Nut M6 Nyloc Decal, Rotor Control Valve Restrictor 3/8 BSP-9/16 JIC Restrictor 3/8 BSP-9/16 JIC Restrictor 3/8 BSP-9/16 JIC Restrictor 3/8" BSP-9/16 JIC Adaptor, Swivel 90-1/4 x 9/16 JIC Adaptor 1/4 BSPF x 9/16 JICM Adaptor 1/2 BSPF-7/8 JIC M

50 CABLE ARMHEAD CONTROL VALVE WITH QUICK RELEASE CABLES (RMB1865-1) October,

51 CABLE ARMHEAD CONTROL VALVE WITH QUICK RELEASE CABLES (RMB1865-1) Ref. Part Description Qty. No. No. Req d. October, Spool Control Valve Relief Valve 140Bar Spring OD.275 x 5/8" Lg Relief Valve Housing Adaptor Relief Body Bonded Seal 3/8" BSP Bonded Seal 1/2" BSP Bonded Seal 1/4" BSP Adap. Rest. 3.2 'E' Adaptor 3/8" BSP MM /8" BSP x 1/2" BSP MM Adaptor Adaptor 3/8" x 1/4" BSP MM Adaptor Tee 1/4" BSP MFM Quick Release Head - Armhead 0.4m Quick Release Cable ACV 3.1m Stud M6 x Cable Armrest W.A.-TMC 5 Lever Decal - Cable, Reach-Angle-Lift Decal - Slew /8" BSP MM Adapter Restrictor Body 1/4" BSP M Restrictor Disc 1.8mm Orifice Capscrew M5 x Bolt M8 x Nyloc Nut M Setscrew M8 x Nut M Adaptor Tee 1/2 BSPMF+1/4M Adaptor Elbow 3/8" BSP MF Nyloc Nut M Decal - Rotor Control Valve Adap. Rest. 1.3mm 3/8" BSP-9/16 JIC Adap. Rest. 1.15mm 3/8" BSP-9/16 JIC Adap. Rest. 1.8mm 3/8" BSP-9/16 JIC Adap. Rest. 1.5mm 3/8" BSP-9/16 JIC /4" BSP F x 9/16" JIC M Swivel Elbow Adaptor 1/4" BSP F x 9/16" JIC M Adaptor 3/8" BSP F x 3/4" JIC M /2" BSP F To 7/8" JIC M Swivel Adaptor /16" JIC FS/FS Green Cable Tie Yellow Cable Tie Blue Cable Tie Red Cable Tie

52 CAB CONTROL MOUNT November, 2013 REF. NO. PART NO. DESCRIPTION QTY Mount Plate Flatwasher 8mm Lockwasher 8mm Wing Nut Capscrew M8 x

53 SHEARTRIM SICKLEBAR (59 WIDE) November, 2014 FOR SHIPPING ONLY Cutter Bar, RH Cutterbar Bracket 80 Box RH /16" JIC FS/FS 450mm Lg Flow Control Valve Adp Hyd Straight 16MJ - 12MBSPP Seal, 3/4 BSP Bonded Adaptor Tee 1" MF + 1/2 BSP MM Adaptor 3/4" x 1" BSP MM Male Union, 1/2 x 1/2 BSP Seal, 1/2 BSP Bonded Adaptor, 1/2 BSP x 1-5/16 M JIC Hose 1/2 BSP STX90 S.Seal Check Valve, 2.0 Bar Adaptor, 1 BSP MF Swept Adaptor 3/4 BSP x 1/2 BSP 1 17 G Adaptor-1/2" BSP MF Elbow Short Capscrew, M10 x Locknut, M10-P Combined Decal Decal, Danger Severed Fingers Decal, Red Reflector Decal, Yellow Reflector Bolt, M8 x Flatwasher, M Hose, 1-5/16 JIC FS/FS 400mm Lg Plug, 1-5/16 JIC Steel Clamp Kit, 4-Bolt > 80 Box

54 FLAILHEAD - SUPERCUT (47 WIDE) December, m Supercut Casing Module LPM Drive Module 54HP 1.2m m Rotor Assy S-Cut F91 Comp m S/Cut Motor Cover Module Pipe Clamp 91 Pair 0.38" Dia Capscrew M10 x Head Decal Roller Assy-1.2m Supercut Head Decal Kit Multicut Clamp Plate - Pipe Clamp Flap Kit, Front

55 CASING - SUPERCUT FLAILHEAD November, Casing - 1.2m Supercut Front Hood Hood Pivot Pin Flap, Rear Clamp Plate Clamp Clamp Strip-Rear Flap Hexb Metric 10-P mm Nut, M Set Screw Hex Head 5/8 UNF 1-1/4 HT Locknut 5/6-NF Toplock Roll Pin M5 x Capscrew 5/8 x 2 3/4 UNF Capscrew 5/8 x 3 UNF

56 November, LPM DRIVE MODULE - SUPERCUT AND MULTICUT Motor Motor Locating Washer Coupling 27 Spline Seal, 3/4 BSP Bonded Adaptor 3/4 x 1-5/16" JIC MM Hydraulic Hose 1-5/16" JIC FS/F Lg Plug 1-5/16" JIC Capscrew, Wedglok

57 ROTOR MODULE - SUPERCUT November, Weldmt, Rotor 1.2m W/A 12 Row Housing Bearing Flail Bolt Washer, Spring- 10mm Dia. BZP Spacer, Cast Flail Single Edge Flail Knife Capscrew M10-P1.5-20mm Grease Fitting 1/ Shim, 1.5 Thick Shim, 2.5 Thick Spacer, Thin- Ref Spacer Thick Bearing 55 x 120 x 29mm 1R Internal Circlip D Plate, Cover Locknut, Toplock 1/2" Washer, Serrated Int.1/2 Dia HHSS 5/8 UNF 1-3/4HT HHSS 5/8 UNF x 1-1/2GRS Locknut, Toplock 5/8" UNF

58 MOTOR COVER 1.2M SUPERCUT November, Motor Cover Capscrew 5/8 x 1/2 UNF Locknut, Toplock 5/8" UNF Hose Retainer

59 ROLLER 1.2 SUPERCUT November, Roller Tube Roller Shaft Roller Bracket LH Roller Bracket RH Seal Carrier Deep Groove Ball Brg 30 x 62 x Seal O Ring Internal Circlip 62mm Dia /4 Internal Spirolox Ring Grease Nipple, 1/8 Straight Bolt M16 x M16 x 45 Coarse H.T Top Lock Nut 16mm-P2.0 ZP Shim-1.2mm Shim - 2.0mm Seal, Rotary Shaft Dia Tab Washer-M24 Special Nut M24 LH Plated 30AF Nut M24 RH Plated 30AF

60 FRONT FLAP KIT, SUPERCUT AND MULTICUT November, Front Flap Front Clamp Strip Carriage Bolt M8 x 25 (Plated) C Locknut, Toplock M8 x P Flatwasher M

61 SKID KIT, SUPERCUT (OPTIONAL) November, Skid W/Assy-Left Hand Skid W/Assy-Right Hand Wear Strip Bolt, Tine 7/16 UNC x 1-3/ Washer Capscrew 5/8 UNF 1-1/4HT Capscrew 5/8 UNF x 1-1/2GRS Locknut, 5/8 x P Locknut 7/16 UNF Standard

62 FLAILHEAD - MULTICUT December, M Dd F.Head Casing Module DMS Roller Flap Kit, Front M Rotor Module F10s.E Cast Multicut Quad Drive Module RH 52-65HP Motor Cover Module LPM Drive Module 54HP 1.2m Head Decal Kit Multicut Shipping Stand, Flail Head

63 ROTOR MODULE - MULTICUT November, Rotor 1.2m Quad Drive M16 x 45 Skt.Csk.Screw BZP Flail, Single Edge Grease Nipple M6 x 1 Straight Bushing, Flail Pivot Top Lock Nut 16mm-P2.0 ZP Capscrew 5/8 NF 3-1/ Lockwasher 5/8 Dia Locknut, Toplock 5/8"

64 ROLLER ASSEMBLY - MULTICUT November, m Roller W.Assy Roller End Cap Roller Bracket Roller Bracket Deep Groove Ball Brg 30 x 62 x Bearing Spacer " Int. Spirolox Ring M10 x 50 Skt Capscrew BZP M16 x 1.5 Grade 8.8 Bolt 60 Lg Nut Grease Nipple, 1/8 BSP-Straight Circlip, External 30mm Dia Shaft Seal 40 x 50 x 7.0 Deep Shim 1.2m DMS Quad Drive

65 QUAD DRIVE MODULE - MULTICUT November, Housing Bearing Nut Capscrew M x 60 Grade Grease Nipple, 1/8 BSP-Straight Grease Fitting 1/8 BSP x 45 Deg Capscrew, Wedglok Plate, Cover Lockwasher 10mm Dia. BZP Capscrew M10-P1.5 x 20mm Bearing 55 x 120 x 29mm 1R Drive Hub Quad Drive Internal Circlip D Spacer, Thin- Ref Spacer Thick

66 MOTOR COVER - MULTICUT November, Motor Cover RH Capscrew M16-1.5P x 40 Lg Locknut, Flanged M16-1.5P Capscrew M16-1.5P x 180 Lg

67 SKID KIT - MULTICUT (OPTIONAL) November, Skid RH Skid LH Wear Strip Bolt, Tine 7/16 UNC x 1-3/ Washer /16 UNF Standard Hexb Metric 12-P mm PL Washer, 12m Form A. BZP Nut Metric 12mm-P1.75 PL

68 STOP MODULE ASSY. - ROTARY HEAD November, 2013 Ref. Part Description Qty. No. No. Req d Stop Module Assembly Stop Pressing Stop Pressing Stop Mtg Pressing Washer Nut Bolt Screw 10 8 T7879 Buffer

69 BEARING UNIT MODULE - ROTARY HEAD November, 2013 Ref. Part Description Qty. No. No. Req d Bearing Unit Assembly BL Spindle Assy 1 2 T8095 Nut Washer Nut 6 5 T2703 Bolt Bolt Stud Washer "O" Ring

70 CASING MODULE - ROTARY HEAD November, 2014 Ref. Part Description Qty. No. No. Req d Casing Module Assembly Cover Casing W/Assy Guard Bar W.A Clamp Strip Clamp Strip Skid -LH Skid -RH Clamp Plate Flap Flap Clamp Strip Flap Washer Nut Nut Nut Bolt Screw Screw Screw Screw Pin Screw Pressing

71 BRACKET MODULE - ROTARY HEAD November, 2013 Ref. Part Description Qty. No. No. Req d Bracket Module Assembly Pivoting W/Assy Greaser Buffer Bush Seal Plug Washer Nut Bolt 4 10 T7942 Nut

72 HYDRAULICS MODULE - ROTARY HEAD November, 2013 Ref. Part Description Qty. No. No. Req d Hydraulic Module Assembly Adaptor Adaptor Adaptor Hose Hose

73 DECAL KIT - ROTARY HEAD November, Ref. Part Description Qty. No. No. Req d Decal Kit Decal Bush Hog Logo Decal Red Reflector Decal Amber Reflector Rivet Serial No Plate 1 6 D559 Decal 1 7 D620 Decal 1 8 D621 Decal 1 9 D626 Decal 2 10 D619 Decal

74 BLADE BAR ASSEMBLY - ROTARY HEAD November, 2014 Ref. Part Description Qty. No. No. Req d Blade Bar Assy. Complete Blade Bar Assy Blade Set w/roll Pins Top Blade Bar Leaf Middle Blade Bar Leaf Bottom Blade Bar Leaf Blade Bolt Lockwasher Nut Lockwasher Bolt 1 x 2-3/4 Gr Bolt 1 x 2 Gr Roll Pin 3/16 x 1-3/ B Washer, Nordlock NL Capscrew 3/4 x 3-3/

75 MOTOR MODULE - ROTARY HEAD November, 2014 Ref. Part Description Qty. No. No. Req d S Motor Module Pipe Motor 80CC SAE C4 Bolt 14T Flange SAE 1-1/ x Seal, Bonded 1.5 BSP Adaptor 1-1/2 BSPM x 1-5/16 JICM Adaptor, Swivel 1 BSPF x 1-5/16 JICF /4 Sckt. Hd Plug Adaptor, 1 x 1-1/2 BSP Plastic Tie Red Blue Cable Tie 150mm

76 LIFT FLOAT KIT (OPTIONAL) November,

77 LIFT FLOAT KIT (OPTIONAL) November, Accumulator 1L 25 Bar PC Bracket Float Kit 1 3 G Adaptor 3/8 BSP x M22 M-M M22 Bonded Seal Seal, 3/8 BSP Bonded Valve, Ball Union 3/8 BSPM x 3/8 BSPM Disc, Restrictor-1.5mm Orifice Spring.275 x 23 Swg x 5/8 Lg Adaptor Rest. Body 3/8mm Hose 3/4" JIC FS/F Adaptor-Tee 3/8F-3/8M+3/8M Nyloc Nut M Capscrew M12-P mm PL Adaptor 3/8" BSP F x 3/4" JIC M Connector, 3/8 BSP 90 Deg

78 LIGHT KIT (Optional for RMB1865 & RMB1865E Only) November, Pin Socket Plastic 12V Cable Tie-4.8 Wide x 120 Lg Light Guard & Mtg - Rear Cover Light Mounting Bracket NS Light Guard & Mounting Lighting Kit Flatwasher, 10.5 x 23.5 x Nyloc Nut M Nyloc Nut M Nyloc Nut M Capscrew M10-P mm Capscrew M12 x Capscrew M5 x 30 Socket M6 x 12 Taptite

79 LIGHT KIT (Standard for RMB & RMB1865E-1 Only) November, Cable Tie Wide x 120 Lg R Light Guard & Mtg, BH Red R Light Mounting Bracket, BH Red R NS Light Guard & Mounting, BH Red Lighting Kit Less Loom Flatwasher, M Nyloc Nut M Nyloc Nut M Bolt, M12 x M6 x 12 Taptite Capscrew M10-P mm Lighting Loom Use 7 Pin Plug

80

81

82 2501 Griffin Ave. Selma, AL (334) (334) Parts Ordering Fax