VERSA PARTS MANUAL. ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas Boom, Flail, Rotary Cutter. Rev Part No.

Transcription

1 VERSA Boom, Flail, Rotary Cutter Rev PARTS MANUAL Part No P ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Alamo Industrial ( ) to obtain a Free copy before operating the equipment Alamo Group, Inc.

2

3 BOLT TORQUE Mounting procedures for mowers will require a significant amount of bolt nut and washer installation. Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values listed in the torque chart based on the bolt size and hardness. Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry values indicated in the chart. Bolt tightness should be completed with and checked with a suitable torque wrench. Torque checks should be completed throughout the life of the mower in accordance with the maintenance chart provided in this manual. Loose bolts on a frame or in a casting may be a result of: Vibration from the mower due to imbalance of the mower blades Pulled threads due to over tightening Distortion of the hole due to under tightening during installation Bolts broken or sheared in the mounting structure or tractor may be the result of: Improper alignment of the Mounting Plate or Structure such that it is not sitting flat on the mating surface Distortion of the bolt due to over-tightening Under tightening of the bolts Check the bolt torque during installation and prior to delivery with a suitable torque wrench.

4 TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.

5 CHANGE PAGES Date of Change Page Number Description of Change (EX- chg pages 17, 23, 137) document release date chg pg chg pg chg pgs 33,45, chg pgs chg pg chg pg /14/2016 chg pgs 256,259,262 12/22/2016 chg pgs /06/2017 chg pages chg pg 109, chg pg added pg 143 added cuttershaft 48 inch flail ecn chg pgs 20,28,129 chgd desc p/n NS chg pgs ecn changed art & bom Change Pages - 5

6 CHANGE PAGES The following is a listing of pages that have been changed since the latest publication date for the overall document. Change Pages - 6

7 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. Note: Please refer to The Safety Section in the front of this Manual for the proper part number when ordering replacement safety decals. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Industrial Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas Alamo Group Inc. Parts Section 2

8 PART NAME INDEX 17 FT - 20 FT & 23 FT - TILT CYLINDER ASY FT - ARTICULATED ARM ASY (PART 1) FT - ARTICULATED ARM ASY (PART 2) FT - BOOM HYDRAULIC SYSTEM (PART 1) FT - BOOM HYDRAULIC SYSTEM (PART 2) FT - DIPPER CYLINDER ASY FT - LIFT CYLINDER ASY FT & 23 FT - ARTICULATED ARM (PART 1) FT & 23 FT - ARTICULATED ARM (PART 2) FT & 23 FT - ARTICULATED ARM (PART 3) FT & 23 FT - DIPPER CYLINDER ASY FT & 23 FT - BOOM HYDRAULIC SYSTEM (PART 1) FT & 23 FT - BOOM HYDRAULIC SYSTEM (PART 2) FT & 23 FT - LIFT CYLINDER ASY IN - BLADE BAR ASY - W- STRAIGHT BLADES IN - X-FRAME SQUARE HEAD ASY IN - X-FRAME SQUARE HEAD PRE-ASY IN SQ HEAD - PAN ASY - STUMP JUMPER IN ROTARY GEAR PAN HEAD ASY W HYD DR - PN IN ROTARY GEAR PAN HEAD SUB-ASY W HYD DR - PN IN & 72 IN - BLADE BAR ASY IN & 72 IN - PAN ASY - STUMP JUMPER IN - BOOM-AXE HEAD ASY IN - HYDRAULIC MOTOR IN - HYDRAULIC MOTOR ASY IN - SPYDER PAN ASY - STUMP JUMPER IN - X-FRAME SQUARE HEAD ASY IN - HYDRAULIC MOTOR IN - HYDRAULIC MOTOR ASY BLADE BAR ASY BLADE BAR ASY - GRASS BUZZBAR - HEAD ASY - 48 IN 2 BLADE - SN (11-01) & UP (PART 1) BUZZBAR - HEAD ASY - 48 IN 2 BLADE - SN (11-01) & UP (PART 2) BUZZBAR - HEAD ASY - 48 IN 2 BLADE - SN (11-01) & UP (PART 3) BUZZBAR - HEAD ASY - 69 IN 3 BLADE - SN (11-01) & UP (PART 1) BUZZBAR - HEAD ASY - 69 IN 3 BLADE - SN (11-01) & UP (PART 2) BUZZBAR - HEAD ASY - 69 IN 3 BLADE - SN (11-01) & UP (PART 3) BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (10-01) & DOWN (PART 1) BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (10-01) & DOWN (PART 2) BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (11-01) & UP (PART 1) Alamo Group Inc. Parts Section -3

9 PART NAME INDEX BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (11-01) & UP (PART 2) BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (11-01) & UP (PART 3) BUZZBAR - HYD MOTOR - PN BUZZBAR - SPINDLE ASY - SN BB & UP CASTER WHEEL ASY - HD FLAIL CHAIN GUARD FRONT & REAR - DOUBLE CONTROL CONSOLE ASY BUMPER KIT - PN CONTROL VALVE - 2 SPOOL COUNTERWEIGHT ASY CUTTER VALVE ASY CUTTER VALVE ASY - WITH FITTINGS CUTTER CONTROL VALVE BLOCK CUTTERSHAFT - DRIVE SIDE ASY - 48 IN & 60 IN CUTTERSHAFT - NON-DRIVE SIDE ASY - 48 IN & 60 IN CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 1) (SN TO CURRENT) CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 2) (SN TO CURRENT) CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 1) CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 2) DEEP DECK ( W-COOLING TUBE ) HYD MOTOR ASY DEEP DECK ( W-O COOLING TUBE ) HYD MOTOR ASY DEEP DECK MOTOR & SPINDLE DEEP DECK MOWER ASY DITCHER - BLADE HEAD ASY DITCHER - BLADE HOUSING DITCHER - BLADE HOUSING ASY - REVERSE ROTATION DITCHER - CONTROL VALVE DITCHER - DEFLECTOR CYL ASY DITCHER - HEAD ASY DITCHER - HYD MOTOR PARTS - PN DITCHER - HYD MOTOR PARTS - PN (AFTER ) DITCHER - HYD SYSTEM - VERSA (PART 1) DITCHER - HYD SYSTEM - VERSA (PART 2) DITCHER - HYD SYSTEM - VERSA BOOM DITCHER - SPINDLE ASY EXTENSION ARM ASY EXTENSION ARM HVY DTY - SPECIAL 6 IN SHORTER THAN STD FILTER ASY FLAIL HEAD ASY - HVY DTY - 48 IN & 60 IN (PART 1) Alamo Group Inc. Parts Section -4

10 PART NAME INDEX FLAIL HEAD ASY - HVY DTY - 48 IN & 60 IN (PART 2) FLAIL HEAD ASY - HVY DTY - 48 IN CUTTERSHAFT HYDRAULIC SCHEMATIC HYDRO FLOAT OPTION JOYSTICK CONSOLE ASY KING POST ATTACHMENT - W-PLAIN BUSHING KING POST ATTACHMENT - W-SERRATED BUSHING LIFT CYLINDER ASY LIFT CYLINDER P/N A MOTOR ASY W-FITTINGS - SPLINED MOTOR PARTS - PN & PN (MODEL NO & ) MOTOR PARTS - PN (MODEL NO ) MOTOR PARTS - PN (MODEL NO ) MOUNTING COMPONENTS - COMMON PARTS BOX (OPTION) OIL RESERVOIR ASY PUMP ASY - SINGLE FRONT - PN PUMP ASY - SINGLE REAR - PN PUMP ASY - TANDEM FRONT - PN PUMP ASY - TANDEM FRONT W- 1-I/4 IN FLANGE - PN * PUMP ASY - TANDEM REAR - PN PUMP PARTS - SINGLE FRONT - PN PUMP PARTS - SINGLE REAR - PN PUMP PARTS - TANDEM FRONT - PN PUMP PARTS - TANDEM FRONT - PN PUMP REPAIR PARTS - TANDEM REAR - PN SKID SHOE EXTENSION KIT SPEED INCREASER - PN (ALUMINUM HSG) SPEED INCREASER - PN (STEEL HSG) SPINDLE & HOUSING ASY SPINDLE HOUSING & SPINDLE ASY SPINDLE HOUSING & SPINDLE ASY - PN C SWING CYLINDER ASY TAIL WHEEL ASY TILT CYLINDER ASY TILT CYLINDER ASY - VERSA EXTENSION ARM TIMBERCAT HEAD ASY (PART 1) TIMBERCAT HEAD ASY (PART 2) VALVE - BOOM CONTROL - 4 SPOOL VALVE ASSEMBLY - 4 SPOOL FIXED DISPLACEMENT (OPTION) Alamo Group Inc. Parts Section -5

11 PART NAME INDEX VALVE ASSEMBLY - 5 SPOOL FIXED DISPLACEMENT (OPTION) VALVE ASSEMBLY - OCFD SYS 4 SPOOL (OPTION) VALVE ASSEMBLY - OCFD SYS 5 SPOOL (OPTION) VALVE BANK COVER VALVE COVER INSTALLATION VALVE REMOTE CONTROL VALVE SEGMENT - INDIVIDUAL SEGMENT - NON-FLOAT VALVE SEGMENT - INDIVIDUAL SEGMENTS - FLOAT VERSA BOOM INSERT ASY VERSA FLAIL & FLAIL AXE - HYD MOTOR ASY - P/N VERSA FLAIL & FLAIL AXE - HYD MOTOR REPAIR PARTS - P/N VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 1) VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 2) VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 3) VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 4) VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 1) VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 2) VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 3) VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 4) VERSA FLAIL ASY - 88 IN PN & PN (PART 1) VERSA FLAIL ASY - 88 IN PN & PN (PART 2) VERSA FLAIL ASY - 88 IN PN & PN (PART 3) VERSA FLAIL ASY - 88 IN PN & PN (PART 4) VERSA MOWER - FLAIL VALVE VERSA MOWER HEAD ASY - 5 FT BAR ( ) VERSA MOWER HEAD SUB ASSY - 5 FT BAR ( ) VERSA MOWER HEAD ASSY - 5 FT PAN ( ) VERSA MOWER HEAD SUB ASSY - 5 FT PAN ( ) VERSA MOWER HEAD ASSY - 5 FT PAN WITH BREAKAWAY ( ) VERSA MOWER HEAD SUB ASSY - 5 FT PAN WITH BREAKAWAY ( ) VERSA MOWER HEAD ASSY - 6 FT BAR ( ) VERSA MOWER HEAD SUB ASSY - 6 FT BAR ( ) VERSA MOWER HEAD ASY 6 FT PAN ( ) VERSA MOWER HEAD SUB ASSY - 6 FT PAN ( ) VERSA MOWER HEAD - CHAIN GUARD - PN VERSA MOWER HEAD - MOTOR & SPINDLE ASSEMBLY PN VERSA MOWER HYDRAULIC SYSTEM (PART 1) VERSA MOWER HYDRAULIC SYSTEM (PART 2) Alamo Group Inc. Parts Section -6

12 17 FT - 20 FT & 23 FT - TILT CYLINDER ASY HYDRAULIC CYLINDER ASY., W/ BUSHINGS TUBE WLD`MT CYLINDER HEAD PISTON ROD WLD`MT * O-RING * ROD SEAL * ROD WIPER SEAL * RING SEAL * PIN 10 5JRC PISTON NUT * PIN ELBOW SEAL KIT TEFLON BUSHING TEFLON BUSHING 2017 Alamo Group Inc. Parts Section -8

13 17 FT - ARTICULATED ARM ASY (PART 1) 2017 Alamo Group Inc. Parts Section -9

14 17 FT - ARTICULATED ARM ASY (PART 1) Continued BOLT FLATWASHER LOCKNUT LOCKNUT COTTER PIN LOCKWASHER 9 15B WASHER 1 SAE PLT LOCKNUT LOCKWASHER SLEEVING NUT BOLT BUSHING GROMMET T 1 LINKAGE ARM ASY. W/ TEFLON BEARINGS C 1 LINKAGE ARM ASY. W/ CONNEX BUSHINGS CYL ROD GUARD ASSEMBLY HOSE HOSE HOSE ELBOW ELBOW TUBE CLAMP TUBE - LOWER TUBE - UPPER SLEEVING ADAPTER ` DIPPER SECTION WLD`MT TUBE - DIPPER ` LIFT SECTION WLD`MT HOSE HOSE MAIN PIN BEARING LG PIN, HEAD TILT, VERSA SM PIN, HEAD TILT, VERSA PIN - DIPPER BEARING PIN - TILT CYLINDER PIN - DIPPER CYLINDER PIN 2017 Alamo Group Inc. Parts Section -10

15 17 FT - ARTICULATED ARM ASY (PART 2) 2017 Alamo Group Inc. Parts Section -11

16 17 FT - ARTICULATED ARM ASY (PART 2) Continued SPACER PIN DIPPER CYLINDER ASY TILT CYLINDER ASY LINKAGE ARM SET SCREW WASHER BUSHING BUSHING BEARING BOLT BEARING LIFT CYLINDER ASY HOSE KING POST BOLT NUT HOSE HOSE BUSHING BUSHING BOLT BUSHING ROLL PIN 7/32 X 1.5 ZN ROLL PIN 7/32 X 1.75 ZN 68 15B WASHER 3/4 P SAE 2017 Alamo Group Inc. Parts Section -12

17 17 FT - BOOM HYDRAULIC SYSTEM (PART 1) 2017 Alamo Group Inc. Parts Section -13

18 17 FT - BOOM HYDRAULIC SYSTEM (PART 1) Continued FLANGE KIT IN TANK FILTER FILTER ELEMENTS ADAPTER ELBOW ADAPTER ADAPTER HOSE BIB ELBOW ADAPTER HOSE-CONTROL VALVE TO SWING CYLINDER HOSE-CONTROL VALVE TO LIFT CYLINDER ELBOW - 90 DEGREES HOSE-CONTROL VALVE TO LIFT CYLINDER ELBOW 45 DEGREES HOSE-TANK TO PUMP HOSE-PUMP TO CUTTER VALVE HOSE-PUMP TO CONTROL VALVE HOSE-CONTROL VALVE TO DIPPER CYL HOSE-CONTROL VALVE TO TILT CYLINDER HOSE-CUTTER VALVE TO TEE HOSE-CONTROL VALVE TO CUTTER VALVE HOSE-CONTROL VALVE TO DIPPER CYL HOSE-CONTROL VALVE TO TILT CYLINDER HOSE CLAMP FILTER RETURN TUBE ADAPTER ELBOW - 90 DEGREES ADAPTER - STRAIGHT HOSE-CUTTER VALVE TO BULKHEAD TUBE - LIFT SECTION, LOWER HOSE - TUBE TO TUBE TUBE - LIFT SECTION, UPPER TUBE HOSE-MOTOR TO BULKHEAD (ROTARY) HOSE-MOTOR TO BULKHEAD (FLAIL) HOSE-MOTOR TO BULKHEAD (FLAIL AXE) HOSE-MOTOR TO BULKHEAD (FLAIL AXE) ELBOW - BULKHEAD SPLIT FLANGE KIT ADAPTER 2017 Alamo Group Inc. Parts Section -14

19 17 FT - BOOM HYDRAULIC SYSTEM (PART 2) 2017 Alamo Group Inc. Parts Section -15

20 17 FT - BOOM HYDRAULIC SYSTEM (PART 2) Continued ELBOW-45 DEGREE 2017 Alamo Group Inc. Parts Section -16

21 17 FT - DIPPER CYLINDER ASY DIPPER CYLINDER ASY, W/ FITTINGS B 1 CYLINDER, W/O FITTINGS CYLINDER HEAD ROD WLD`MT TUBE WLD`MT PISTON 6 5JRC LOCKNUT SETSCREW ADAPTER, ELBOW TEFLON BUSHING TEFLON BUSHING SEAL KIT 2017 Alamo Group Inc. Parts Section -17

22 17 FT - LIFT CYLINDER ASY Alamo Group Inc. Parts Section -18

23 17 FT - LIFT CYLINDER ASY. Continued LIFT CYLINDER ASY., W/ FITTINGS A 1 CYLINDER, W/O FITTINGS ADAPTER, ELBOW CONNEX BUSHING CYLINDER ROD WLD`MT CYLINDER HEAD, GLAND PISTON CYLINDER TUBE WLD`MT 8 5JRC LOCKNUT SEAL KIT 2017 Alamo Group Inc. Parts Section -19

24 20 FT & 23 FT - ARTICULATED ARM (PART 1) 2017 Alamo Group Inc. Parts Section -20

25 20 FT & 23 FT - ARTICULATED ARM (PART 1) Continued A 1 20` ARTICULATED ARM ASY A 1 23` ARTICULATED ARM ASY LOCKNUT TLM 1/2 NC PLC FLATWASHER BOLT FLATWASHER LOCKNUT LOCKNUT BOLT COTTER PIN LOCKWASHER 12 15B WASHER 1 SAE PLT CORDURA SLEEVING - 30" LG LOCKNUT LOCKWASHER HOSE # 4-4FJX - 4FJX - 184" LG - 20` HOSE # 4-4FJX - 4FJX - 200" LG - 23` HOSE # 4-4FJX - 4FJX - 200" LG - 20` HOSE # 4-4FJX - 4FJX " LG - 23` CORDURA SLEEVING - 48" LG JAM NUT BOLT HOSE # 4-4FJX - 4FJX -172" LG - 20` HOSE # 4-4FJX - 4FJX -163" LG - 23` RUBBER GROMMET T 1 LINKAGE ARM ASY. - W/ TEFLON BUSHINGS HOSE # 4-4FJX - 4MJ -114" LG - 20` HOSE # 4-4FJX - 4MJ -148" LG - 23` HOSE # 4-4FJX - 4MJ - 96" LG - 20` HOSE # 4-4FJX - 4MJ -129" LG - 23` CYL ROD GUARD ASSEMBLY CONNEX BUSHING ADAPTER, HYD, ELBOW LARGE BOOM WLD`MT - 20` LARGE BOOM WLD`MT - 23` TUBE CLAMP TOP FOUR LINKAGE HYD TUBE LOWER TUBE - 23` TOP FOUR LINKAGE HYD TUBE UPPER TUBE - 23` DIPPER SECTION TUBE - 20` 2017 Alamo Group Inc. Parts Section -21

26 20 FT & 23 FT - ARTICULATED ARM (PART 2) 2017 Alamo Group Inc. Parts Section -22

27 20 FT & 23 FT - ARTICULATED ARM (PART 2) Continued DIPPER SECTION TUBE - 23` DIPPER SECTION TUBE - 20` DIPPER SECTION TUBE - 23` HOSE 20-20FJX - 20FJX90-52LG - 20` HOSE 20-20FJX - 20FJX90-52LG - 20` HYDRAULIC TUBING COVER BOOM, DIPPER WLD`MT - 20` BOOM, DIPPER WLD`MT - 23` CORDURA SLEEVING - 54" LG DIPPER CYLINDER ASY CLAMP TOP BRACKET BOLT MAIN PIN WLD`MT TEFLON BUSHING LG PIN, HEAD TILT, VERSA SM PIN, HEAD TILT, VERSA MAIN PIN WLD`MT ( NEW STYLE ) BUSHING TILT CYLINDER PIN WLD`MT DIPPER PIN ( W/ NUT & WASHER ) TOGLE PIN WLD`MT SPACER DIPPER CYLINDER PIN TILT CYLINDER ASY LINKAGE ARM ASY FLATWASHER BUSHING HOSE # 4-4FJX - 4FJX -114" LG HOSE # 4-4FJX - 4FJX - 80" LG KING POST ( SEE KING POST SECTION ) MAIN PIN BUSHING ( SEE KING POST SECTION ) LIFT CYLINDER ASY JAM NUT BUSHING TEFLON BEARING BOLT TEFLON BEARING TEFLON BEARING BUSHING BUSHING 2017 Alamo Group Inc. Parts Section -23

28 20 FT & 23 FT - ARTICULATED ARM (PART 3) 2017 Alamo Group Inc. Parts Section -24

29 20 FT & 23 FT - ARTICULATED ARM (PART 3) Continued ROLL PIN 7/32 X 1.5 ZN ROLL PIN 7/32 X 1.75 ZN 75 15B WASHER 3/4 P SAE 2017 Alamo Group Inc. Parts Section -25

30 20 FT & 23 FT - DIPPER CYLINDER ASY B 1 HYDRAULIC CYL GLAND O RING BARREL ASY PISTON 7 5JRC LOCKNUT ELBOW BOLT FLATWASHER LOCKNUT PIN PIN BUSHING COLLAR WEAR RING PISTON SEAL O RING SET SCREW 2017 Alamo Group Inc. Parts Section -26

31 20 FT & 23 FT - DIPPER CYLINDER ASY Continued ROD WIPER ROD SEAL BUFFER SEAL BACK-UP RING BUSHING SET SCREW WASHER LOCKNUT SEAL KIT 2017 Alamo Group Inc. Parts Section -27

32 20 FT & 23 FT - BOOM HYDRAULIC SYSTEM (PART 1) 2017 Alamo Group Inc. Parts Section -28

33 20 FT & 23 FT - BOOM HYDRAULIC SYSTEM (PART 1) Continued FLANGE KIT ADAPTER STRAIGHT ELBOW - 90 DEG RETURN TUBE STRAIGHT ADAPTER ADAPTER HOSE BIB ELBOW - 90 DEG ADAPTER STRAIGHT TUBE - DIPPER TUBE - DIPPER - ( 23` ) FILTER RETURN TUBE ELBOW - 90 DEG FILTER FILTER REPLACEMENT ELEMENT ADAPTER - STRAIGHT BOTTOM TUBE - LIFT SECTION - ( 23` ) TOP FOUR LINKAGE HYD TUBE ELBOW - 90 DEG ELBOW - 90 DEG HOSE CLAMP HOSE - CONTROL VALVE TO HOSE ELBOW - BULKHEAD ADAPTER STRAIGHT HOSE HOSE - ( 23` ) SPILT FLANGE KIT ELBOW ELBOW - 45 DEGREES HOSE - RESERVOIR TANK TO PUMP HOSE - PUMP TO CUTTER VALVE HOSE - PUMP TO CONTROL VALVE HOSE HOSE - TUBE TO TUBE 35 TOP FOUR LINKAGE 1 HYD TUBE TOP TUBE - LIFT SECTION TOP TUBE - LIFT SECTION - ( 23` ) REAR TUBE - DIPPER REAR TUBE - DIPPER - ( 23` ) HOSE - HOSE TO TILT CYLINDER HOSE - HOSE TO TILT CYLINDER - ( 23` ) HOSE - TUBE TO CUTTER VALVE 2017 Alamo Group Inc. Parts Section -29

34 20 FT & 23 FT - BOOM HYDRAULIC SYSTEM (PART 2) 2017 Alamo Group Inc. Parts Section -30

35 20 FT & 23 FT - BOOM HYDRAULIC SYSTEM (PART 2) Continued HOSE - HOSE TO TILT CYLINDER HOSE - HOSE TO TILT CYLINDER - ( 23` ) HOSE - MOTOR TO BULKHEAD (ROTARY) HOSE - MOTOR TO BULKHEAD (FLAIL) HOSE - MOTOR TO BULKHEAD (FLAIL AXE) HOSE - MOTOR TO BULKHEAD (FLAIL AXE) HOSE - CONTROL VALVE TO SWING CYLINDER HOSE - CONTROL VALVE TO LIFT CYLINDER HOSE - CONTROL VALVE TO LIFT CYLINDER HOSE - CONTROL VALVE TO DIPPER CYLINDER HOSE - CONTROL VALVE TO DIPPER - ( 23` ) 2017 Alamo Group Inc. Parts Section -31

36 20 FT & 23 FT - LIFT CYLINDER ASY LIFT CYLINDER ASSY A/B TUBE WLDMT 4.00 X STROKE CYL HEAD THD W/RING PISTON S-W-PSP ROD WLDMT 2.00 X STROKE NUT HEX LOCK 1-1/4 NF GRB BSHG CONX 1-1/4X1 X 7/ ADP HYD ELBOW 4MB-4MJ A 1 HYD CYLINDER 4BORE X SEAL KIT 2017 Alamo Group Inc. Parts Section -32

37 50 IN - BLADE BAR ASY - W- STRAIGHT BLADES TOP LEAF BOTTOM LEAF BLADE SET BLADE BOLT SLOTTED NUT LOCKWASHER SPIRAL ROLL PIN BOLT LOCKWASHER SOCKET HEAD CAPSCREW LOCKWASHER 2017 Alamo Group Inc. Parts Section -33

38 50 IN - X-FRAME SQUARE HEAD ASY 2017 Alamo Group Inc. Parts Section -34

39 50 IN - X-FRAME SQUARE HEAD ASY Continued " X-FRAME SQUARE HEAD ASY SQUARE HEAD WLD`MT, 50" HITCH POST - 4 BAR GREASE FITTING BUSHING BOLT LOCKNUT MOTOR BOLT DOOR LOCK PIN CLIP PIN COVER PLATE 11 5F WINGNUT " SQUARE HEAD DOOR WLD`MT BOLT NUT,TOPLOCK 5/8 NC PLC FLAP DEFLECTOR - DOOR FLAP DEFLECTOR - DOOR BOLT FLATWASHER LOCKNUT REAR, FLAP DEFLECTOR SIDE GUARD REAR, FLAP RETAINER BOLT WOODWASHER BLADE BAR BLADE BAR W/ GRASS BLADE BLADE PAN 2017 Alamo Group Inc. Parts Section -35

40 50 IN - X-FRAME SQUARE HEAD PRE-ASY SPINDLE HOUSING/SPINDLE ASY. W/ HYDRAULIC MOTOR & FITTINGS B 1 SPINDLE HOUSING & SPINDLE ASY MOTOR BOLT NUT PAN AND BLADE ASY BOLT LOCKWASHER SKID SHOE ( RIGHT HAND ) SKID SHOE ( LEFT HAND ) BOLT NUT WASHER BOLT SQUARE HEAD WLD`MT 2017 Alamo Group Inc. Parts Section -36

41 THIS PAGE INTENTIONALLY LEFT BLANK 2017 Alamo Group Inc. Parts Section -37

42 50 IN SQ HEAD - PAN ASY - STUMP JUMPER * STUMP JUMPER PAN ASY. - 50" ** STUMP JUMPER PAN ASY. W/O BLADES & BUSHINGS BLADES - MATCHED SET OF BLADES - MATCHED SET OF BLADE BOLT HEAT TREATED WASHER SPIRAL ROLL PIN NUT LOCKNUT WASHER SPACER 10 7A BOLT LOCKWASHER BOLT 2017 Alamo Group Inc. Parts Section -38

43 50 IN SQ HEAD - PAN ASY - STUMP JUMPER Continued KEY BUSHING SPACER 2017 Alamo Group Inc. Parts Section -39

44 50 IN ROTARY GEAR PAN HEAD ASY W HYD DR - PN Alamo Group Inc. Parts Section -40

45 50 IN ROTARY GEAR PAN HEAD ASY W HYD DR - PN Continued ASY, 50" ROT, GEAR, PAN, W/ DR A 1 HYD CYLINDER 2BORE X 9-1/ WELDMENT, DOOR ROD, HINGE S 2 PIN ROLL 1/4 X 3/ FLAP, 8 1/2 X 52 X 5/16 THK BAR, HOLD DOWN, FLAP FLAP, REAR 10 X 53 X 5/16THK BAR, CLAMP, REAR FLATWASHER STD 5/16 - PLATED HHCS 5/16-16UNC 1-1/2 PL LOCKNUT TLM 5/16-NC PLC BOLT 5/16NC X 1-3/4 PL PIN, DRILLED PIN,5/8 X 2-1/ PIN,COTTER 3/16 X 1-1/2 PLATED VINYL TAPE YELLOW 1/4" WIDE VINYL TAPE YELLOW 1/2" WIDE ADP HYD ELBOW 4MB-4MJ MOTOR,HYD, GEAR, 5.73, HP SEAL SPLIT FLANGE KIT 1-1/ VINYL TAPE RED 1/2" WIDE VINYL TAPE BLUE 1/2" WIDE ADP HYD ELBOW 24FL-20MJ VINYL TAPE WHITE 1/4" WIDE HOSE #20-20FJX -20FJX - 50LG HOSE #20-20FJX90-20FJX - 43LG HOSE 4-4FJX-4FJX-80LG (YELLOW/WHITE) HOSE 4-4FJX-4FJX-88LG (YELLOW) KIT, DOOR, 50ROT, ELEC-VALVE 2017 Alamo Group Inc. Parts Section -41

46 50 IN ROTARY GEAR PAN HEAD SUB-ASY W HYD DR - PN Alamo Group Inc. Parts Section -42

47 50 IN ROTARY GEAR PAN HEAD SUB-ASY W HYD DR - PN Continued ASY, 50" ROT, GEAR, PAN, W/ DR LOCKNUT TLM 3/8-NC PLC HHCS 1/2 NC 1-3/4 PL LOCKWASHER, 1/2, HVY, PL SKID SHOE WELDMENT-50 HEAD DECK PAN ASSEMBLY 50 A-BOOM SHCS 3/4 NC 4 PL8 9 15B WASHER 3/8 SAE PLT LOCKWASHER, 3/4, HVY, PL FSCS 3/8 NC 1-1/ A 1 ASY,SPINDLE HOUSING-SPLINED HHCS 3/4 NC 3 PL HHCS 3/4 NC 1-3/4 PL NUT,HEX TOPLOCK 3/4 NC GR.C PL WASHER, 3/4" HARDENED MOTOR,HYD, GEAR, 5.73, HP SEAL SPLIT FLANGE KIT 1-1/ SPACER,1 1/2 BLADE BAR WELDMENT, HITCH POST ADP HYD ELBOW 24FL-20MJ VINYL TAPE RED 1/2" WIDE VINYL TAPE BLUE 1/2" WIDE HOSE #20-20FJX -20FJX - 50LG HOSE #20-20FJX90-20FJX - 43LG HOSE #4-4FJX-4FJX-80LG HOSE #4-4FJX-4FJX-88LG 2017 Alamo Group Inc. Parts Section -43

48 60 IN & 72 IN - BLADE BAR ASY BLADE BAR CARRIER ASY. 60" BLADE BAR CARRIER ASY. 72" BLADE BAR, 60" BLADE BAR, 72" BLADES, MATCHED SET ( 2 ) NUT LOCKWASHER BOLT BLADE LOCKWASHER SOCKET HEAD BOLT ( USE W/O SPACER ) SOCKET HEAD BOLT ( USE W/ SPACER ) SPACER 2017 Alamo Group Inc. Parts Section -44

49 60 IN & 72 IN - PAN ASY - STUMP JUMPER STUMP JUMPER PAN ASY. 60", USE STUMP JUMPER PAN ASY. 72" STUMP JUMPER PAN WLD`MT, 60" STUMP JUMPER PAN WLD`MT, 72" BLADES - MATCHED SET - 60" BLADES - MATCHED SET - 72" BLADE BOLT LOCKWASHER NUT LOCKWASHER BOLT 2017 Alamo Group Inc. Parts Section -45

50 60 IN - BOOM-AXE HEAD ASY " X-FRAME SQUARE HEAD ASY A 1 SQUARE HEAD WLD`MT - 60" HITCH POST - 4 BAR GREASE FITTING BUSHING BOLT LOCKNUT MOTOR BOLT DOOR LOCK PIN CLIP PIN COVER PLATE 11 5F WINGNUT A 1 DOOR BOLT NUT,TOPLOCK 5/8 NC PLC FLAP DEFLECTOR - DOOR FLAP DEFLECTOR - DOOR 2017 Alamo Group Inc. Parts Section -46

51 60 IN - BOOM-AXE HEAD ASY Continued BOLT FLATWASHER LOCKNUT FLAP DEFLECTOR - REAR SIDE GUARD REAR FLAP RETAINER BOLT WOODWASHER 2017 Alamo Group Inc. Parts Section -47

52 60 IN - HYDRAULIC MOTOR SNAP RING *+ "O" RING SEAL RETAINER *+ SEAL MOUNTING FLANGE, W/ BUSHINGS PLUG CHECK ASSEMBLY *+ SEAL END * THRUST PLATE GEAR SET *+ SQUARE SEAL DOWEL PIN 2017 Alamo Group Inc. Parts Section -48

53 60 IN - HYDRAULIC MOTOR Continued GEAR HOUSING PORTING FLANGE, W/ BUSHING WASHER BOLT *+ SIDE SEAL ( NOT SHOWN ) SEAL RETAINER 2017 Alamo Group Inc. Parts Section -49

54 60 IN - HYDRAULIC MOTOR ASY HYDRAULIC MOTOR DEG. ELBOW SPLIT FLANGE KIT FLANGE KIT REDUCER DEG. ELBOW 2017 Alamo Group Inc. Parts Section -50

55 60 IN - SPYDER PAN ASY - STUMP JUMPER PAN ASSEMBLY 60 V/M STUMP PAN ASSY NUT SLOT HVY 1-1/8 NF PL PIN ROLL 3/16X1-3/ WASHER OD DX BLADE SET (3 CW FAN) KEYED BLADE BOLT FOR WASHER, 2-19/32 ID 5.0 OD 3/ BUSHING, BLADE BOLT KEY,5/16 SQ X 15/16 LONG NOTE: INCLUDES ITEMS Alamo Group Inc. Parts Section -51

56 60 IN - X-FRAME SQUARE HEAD ASY " SQUARE HEAD ASY SPINDLE HOUSING/SPINDLE ASY. W/HYDRAULIC MOTOR & FITTINGS (HIGH SPEED) (S/N & AND AB SPINDLE HOUSING/SPINDLE ASY. W/HYDRAULIC MOTOR & FITTINGS (S/N AND PRIOR & ) B 1 SPINDLE HOUSING/SPINDLE ASY MOTOR (HIGH SPEED) (S/N & AND ABOVE) MOTOR (S/N AND PRIOR & ) BOLT NUT BLADE BAR ASY. (ITEMS 19-29) BOLT LOCKWASHER SKID SHOE (RIGHT HAND /2" LONG) SKID SHOE (LEFT HAND /2" LONG) BOLT NUT WASHER BOLT SQUARE HEAD WLD`MT TOP LEAF MIDDLE LEAF BOTTOM LEAF 2017 Alamo Group Inc. Parts Section -52

57 60 IN - X-FRAME SQUARE HEAD ASY Continued BLADE SET BLADE BOLT SLOTTED NUT LOCKWASHER SPIRAL ROLL PIN BOLT BOLT LOCKWASHER Alamo Group Inc. Parts Section -53

58 72 IN - HYDRAULIC MOTOR SNAP RING *+ "O" RING SEAL RETAINER *+ SEAL MOUNTING FLANGE, W/ BUSHINGS PLUG CHECK ASSEMBLY *+ SEAL END * THRUST PLATE GEAR SET *+ SQUARE SEAL DOWEL PIN GEAR HOUSING PORTING FLANGE, W/ BUSHING WASHER 2017 Alamo Group Inc. Parts Section -54

59 72 IN - HYDRAULIC MOTOR Continued BOLT *+ SIDE SEAL ( NOT SHOWN ) SEAL RETAINER 2017 Alamo Group Inc. Parts Section -55

60 72 IN - HYDRAULIC MOTOR ASY HYDRAULIC MOTOR DEG. ELBOW SPLIT FLANGE KIT FLANGE KIT REDUCER DEG. ELBOW 2017 Alamo Group Inc. Parts Section -56

61 BLADE BAR ASY BLADE BAR WLD`MT NUT LOCKWASHER BLADE SET ( USE P/N ) BLADE BOLT 2017 Alamo Group Inc. Parts Section -57

62 BLADE BAR ASY - GRASS GRASS BLADE BAR ASY BLADE BAR WLD`MT BLADE SET BOLT WASHER 5 5JRC NUT 2017 Alamo Group Inc. Parts Section -58

63 THIS PAGE INTENTIONALLY LEFT BLANK 2017 Alamo Group Inc. Parts Section -59

64 BUZZBAR - HEAD ASY - 48 IN 2 BLADE - SN (11-01) & UP (PART 1) 2017 Alamo Group Inc. Parts Section -60

65 BUZZBAR - HEAD ASY - 48 IN 2 BLADE - SN (11-01) & UP (PART 1) Continued SAW BLADE HEAD ASY, 2 BLADE 48" (EXCEPT 28 FT A-BOOM) END CAP BLADE SPACER SPINDLE ASY BOLT, SCKT HD CNTR-SNK 1/2"-NC X 3-1/2" W/HOLE BOLT, SCKT HD CNTR-SNK 1/2"-NC X 2" W/HOLE NUT, SLOTTED 1/2"-NC PLB NUT, HEX 1/2"-NC PL SAW BODY WELDMENT, 2 BLADE TENSION ADJUSTMENT BRACKET NUT, 1/2"-20NF 90DEG CONE LUG PL BOLT, HEX HEAD 1/2"-NC X 3-1/2" PL GR V-BELT SHEAVE W/GROOVE BUSHING, QD SHEET, BELT COVER, LEFT 2 BLADE STUD, QUICK RELEASE W/RING RETAINER F/ QUICK RELEASE RECEIVER F/ QUICK RELEASE BOLT, HEX HEAD 3/8"-NC X 1 PL GR FLATWASHER, 3/8" PL STD LOCKNUT TLM 1/2 NC PLC DRIVE SPINDLE ASY MOTOR, GEAR TYPE BOLT, HEX HEAD 1/2"-13NC X 1-3/4" PL GR HUB, 1-1/8" BORE X 1/4" KEY INSERT, URETHANE COVER, PROTECTIVE NYLON HUB, 1" BORE BELT COVER, SHORT HITCH POST WELDMENT LOCKNUT, TOPLOCK 3/4"-NC PLC PLATE, HITCH POST CLAMP BOLT, HEX HEAD 3/4"-10NC X 2" PL GR HITCH TUBE WELDMENT, 2 BLADE LOCKNUT, TOPLOCK 3/8"-NC PLB BOLT, HEX HEAD 3/8"-16NC X 1-1/2" PL GR BUMPER SHIELD WELDMENT, REAR SAW BLADE PACKAGE OF ADAPTER, HYD 20FL-20MJ90 (EXCEPT 28 FT A-BOOM) 2017 Alamo Group Inc. Parts Section -61

66 BUZZBAR - HEAD ASY - 48 IN 2 BLADE - SN (11-01) & UP (PART 2) 2017 Alamo Group Inc. Parts Section -62

67 BUZZBAR - HEAD ASY - 48 IN 2 BLADE - SN (11-01) & UP (PART 2) Continued SPLIT FLANGE KIT, # ADAPTER, HYD 20FJX-20MJ45 (EXCEPT 28 FT A-BOOM) FLATWASHER, 1/4" BOLT, HEX HEAD 1/4" X MANIFOLD BLOCK O-RING RELIEF CARTRIDGE HOSE, #20-20FJX-20FJX-68"LG (EXCEPT 28 FT A-BOOM) HOSE, #20-20FJX-20FJX-82"LG (EXCEPT 28 FT A-BOOM) CORDURA SLEEVE DECAL, WARNING BELT SHIELD DECAL, USE/REPAIR GUARDS DECAL, BLADES THROWN OBJECTS DECAL, REPLACE PARTS DECAL, TRACTOR OPERATOR SAFETY DECAL, PINCH POINTS DECAL, SHIELD MISSING DECAL, WARNING HOSE BURST DECAL-MULTI HAZ DECAL, ALAMO INDUSTRIAL LOGO DECAL, BUZZBAR 62 D138 1 DECAL, BLADE ROTATION DECAL, HEAR PROTECTION REQD DECAL, ROTATING BLADES DECAL, WARNING DISCONNECT DECAL, NO HITCH POST HERE NFS SERIAL NUMBER PLATE BB NFS METAL TACK ADAPTER, HYD 20MJ-20FJX90 (EXCEPT 28 FT A-BOOM) DECAL, RED REFLECTOR DECAL, YELLOW REFLECTOR GREASE FITTING NUT, 1"-NC BUSHING BOLT, HEX HEAD 1"-NC X 9" BOLT, HEX HEAD 3/4"-NC KEY, 1/4" SQ KEY X 1-1/4" LG PLUG INSERT SHEET, BUZZBAR (EXCEPT 28 FT A-BOOM) 2017 Alamo Group Inc. Parts Section -63

68 BUZZBAR - HEAD ASY - 48 IN 2 BLADE - SN (11-01) & UP (PART 3) 2017 Alamo Group Inc. Parts Section -64

69 BUZZBAR - HEAD ASY - 48 IN 2 BLADE - SN (11-01) & UP (PART 3) Continued VINYL TAPE BLUE 1/2" WIDE VINYL TAPE RED 1/2" WIDE COTTER PIN, 1/8" X 1" WASHER, PLATED MOTOR MOUNT TUBE, MACHINED 2017 Alamo Group Inc. Parts Section -65

70 BUZZBAR - HEAD ASY - 69 IN 3 BLADE - SN (11-01) & UP (PART 1) 2017 Alamo Group Inc. Parts Section -66

71 BUZZBAR - HEAD ASY - 69 IN 3 BLADE - SN (11-01) & UP (PART 1) Continued SAW BLADE HEAD ASY, 69 INCH 3 BLADE ) END CAP BLADE SPACER SPINDLE ASY BOLT, SCKT HD CNTR-SNK 1/2"-NC X 3-1/2" W/HOLE BOLT, SCKT HD CNTR-SNK 1/2"-NC X 2" W/HOLE NUT, SLOTTED 1/2"-NC PLB NUT, HEX 1/2"-NC PL SAW BODY WELDMENT, 3 BLADE TENSION ADJUSTMENT BRACKET NUT, 1/2"-20NF 90DEG CONE LUG PL BOLT, HEX HEAD 1/2"-NC X 3-1/2" PL GR V-BELT SHEAVE W/GROOVE BUSHING, QD SHEET, BELT COVER, LEFT 3 BLADE STUD, QUICK RELEASE W/RING RETAINER F/QUICK RELEASE RECEIVER F/ QUICK RELEASE BOLT, HEX HEAD 3/8"-NC X 1 PL GR FLATWASHER, 3/8" PL STD LOCKNUT TLM 1/2 NC PLC DRIVE SPINDLE ASY MOTOR, GEAR TYPE BOLT, HEX HEAD 1/2"-13NC X 1-3/4" PL GR HUB, 1-1/8" BORE X 1/4" KEY INSERT, URETHANE COVER, PROTECTIVE NYLON HUB, 1" BORE BELT COVER, SHORT HITCH POST WELDMENT LOCKNUT, TOPLOCK 3/4"-NC PLC PLATE, HITCH POST CLAMP BOLT, HEX HEAD 3/4"-10NC X 2" PL GR HITCH TUBE WELDMENT, 3 BLADE LOCKNUT, TOPLOCK 3/8"-NC PLB BOLT, HEX HEAD 3/8"-16NC X 1-1/2" PL GR BUMPER SHIELD WELDMENT, REAR SAW BLADE PACKAGE OF ADAPTER, HYD 20FL-20MJ Alamo Group Inc. Parts Section -67

72 BUZZBAR - HEAD ASY - 69 IN 3 BLADE - SN (11-01) & UP (PART 2) 2017 Alamo Group Inc. Parts Section -68

73 BUZZBAR - HEAD ASY - 69 IN 3 BLADE - SN (11-01) & UP (PART 2) Continued SPLIT FLANGE KIT, # ADAPTER, HYD 20FJX-20MJ FLATWASHER, 1/4" BOLT, HEX HEAD 1/4" X MANIFOLD BLOCK O-RING RELIEF CARTRIDGE HOSE, #20-20FJX-20FJX-68"LG HOSE, #20-20FJX-20FJX-82"LG CORDURA SLEEVE DECAL, WARNING BELT SHIELD DECAL, USE/REPAIR GUARDS DECAL, BLADES THROWN OBJECTS DECAL, REPLACE PARTS DECAL, TRACTOR OPERATOR SAFETY DECAL, PINCH POINTS DECAL, SHIELD MISSING DECAL, WARNING HOSE BURST DECAL-MULTI HAZ DECAL, ALAMO INDUSTRIAL LOGO DECAL, BUZZBAR 62 D138 1 DECAL, BLADE ROTATION DECAL, HEAR PROTECTION REQD DECAL, ROTATING BLADES DECAL, WARNING DISCONNECT DECAL, NO HITCH POST HERE NFS SERIAL NUMBER PLATE BB NFS METAL TACK ADAPTER, HYD 20MJ-20FJX DECAL, RED REFLECTOR DECAL, YELLOW REFLECTOR GREASE FITTING NUT, 1"-NC BUSHING BOLT, HEX HEAD 1"-NC X 9" BOLT, HEX HEAD 3/4"-NC KEY, 1/4" SQ KEY X 1-1/4" LG PLUG INSERT SHEET, BUZZBAR 2017 Alamo Group Inc. Parts Section -69

74 BUZZBAR - HEAD ASY - 69 IN 3 BLADE - SN (11-01) & UP (PART 3) 2017 Alamo Group Inc. Parts Section -70

75 BUZZBAR - HEAD ASY - 69 IN 3 BLADE - SN (11-01) & UP (PART 3) Continued VINYL TAPE BLUE 1/2" WIDE VINYL TAPE RED 1/2" WIDE COTTER PIN, 1/8" X 1" WASHER, PLATED MOTOR MOUNT TUBE, MACHINED 2017 Alamo Group Inc. Parts Section -71

76 BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (10-01) & DOWN (PART 1) 2017 Alamo Group Inc. Parts Section -72

77 BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (10-01) & DOWN (PART 1) Continued BUZZBAR ASSEMBLY END CAP BLADE SPACER HUB ASY BOLT BOLT SLOTTED NUT HEX NUT BLADE SAW BODY WLD`MT TENSION ADJUSTMENT BRACKET NUT BOLT BELT MICRO-V SHEAVE QD BUSHING BELT COVER, LONG STUD, QUICK RELEASE RETAINER, QUICK RELEASE RECEIVER, QUICK RELEASE BOLT FLATWASHER LOCKNUT TLM 1/2 NC PLC ASSEMBLY, DRIVE SPINDLE MOTOR GEAR BOLT BRACKET MOTOR ADJUSTMENT FLAT SOCKET HEAD BOLT RUBBER COUPLING, A-BOOM MOTOR HUB, 20R10 W/ 1" BORE BELT COVER, SHORT HITCH POST, A-BOOM LOCKNUT CLAMP BOLT HITCH TUBE WLD`MT LOCKNUT BOLT BUMPER REAR SHIELD WLD`MT SAW BLADE PACK ( 2 BLADES PER PACK SHIPPED UNMOUNTED ) ADAPTER 2017 Alamo Group Inc. Parts Section -73

78 BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (10-01) & DOWN (PART 2) 2017 Alamo Group Inc. Parts Section -74

79 BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (10-01) & DOWN (PART 2) Continued SPLIT FLANGE KIT ADAPTER FLATWASHER BOLT MANIFOLD BLOCK O-RING RELIEF CARTRIDGE HOSE HOSE CORDURA SLEEVE QD - MODIFIED BUSHING GREASE FITTING NUT BUSHING BOLT BOLT SQUARE KEY PLUG VINYL TAPE BLUE 1/2" WIDE VINYL TAPE RED 1/2" WIDE COTTER PIN ( SHIPPED UNMOUNTED ) WASHER ADAPTER MACHINED MOTOR MOUNT DRIVE SHIELD BOLT SETSCREW 2017 Alamo Group Inc. Parts Section -75

80 BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (11-01) & UP (PART 1) 2017 Alamo Group Inc. Parts Section -76

81 BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (11-01) & UP (PART 1) Continued SAW HEAD ASY, 90 INCH 4 BLADE END CAP BLADE SPACER SPINDLE HUB ASY BOLT, SCKT HD CNTRSNK 1/2"-NC X 3-1/2" W/HOLE BOLT, SCKT HD CNTRSNK 1/2"-NC X 2" W/HOLE NUT, SLOTTED 1/2"-NC PLB NUT, HEX 1/2"-NC PL SAW BODY WELDMENT, 4 BLADE TENSION ADJUSTMENT BRACKET NUT, 1/2"-20NF - 90 DEG.CONE LUG PL BOLT, HEX HEAD1/2"-NC X 3-1/2" PL GR BELT, POLY-V SHEAVE, PULLEY BUSHING, QD SHEET, BELT COVER, LEFT 4 BLADE STUD, QUICK RELEASE W/RING RETAINER F/ QUICK RELEASE RECEIVER F/ QUICK RELEASE BOLT, HEX HEAD 3/8"-NC X 1" PL GR FLATWASHER, 3/8" PL STD LOCKNUT TLM 1/2 NC PLC DRIVE SPINDLE ASY MOTOR, GEAR TYPE BOLT, HEX HEAD 1/2"-13NC X 1-3/4" PL GR HUB, 1-1/8" BORE 1/4" KEY INSERT, URETHANE COVER, PROTECTIVE NYLON HUB, 1" BORE BELT COVER, SHORT HITCH POST WELDMENT LOCKNUT, TOPLOCK 3/4"-NC PLC PLATE, HITCH POST CLAMP BOLT, HEX HEAD 3/4"-10NC X 2" PL GR HITCH TUBE WELDMENT, 4 BLADE LOCKNUT, TOPLOCK 3/8"-NC PLB BOLT, HEX HEAD 3/8"-16NC X 1-1/2" PL GR BUMPER SHIELD WELDMENT, REAR 4 BLADE SAW BLADE SET, SET OF 2 BLADES ADAPTER, HYD 20FL-20MJ Alamo Group Inc. Parts Section -77

82 BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (11-01) & UP (PART 2) 2017 Alamo Group Inc. Parts Section -78

83 BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (11-01) & UP (PART 2) Continued SPLIT FLANGE KIT, # ADAPTER, HYD 20FJX-20MJ FLATWASHER, 1/4" PL BOLT, HEX HEAD 1/4" X 3" MANIFOLD BLOCK O-RING RELIEF CARTRIDGE HOSE, #20-20FJX-20FJX90-82"LG HOSE, #20-20FJX-20FJX-68"LG CORDURA SLEEVE DECAL, WARNING BELT SHIELD DECAL, USE/REPAIR GUARDS DECAL, BLADES THROWN OBJECTS DECAL, REPLACEMENT PARTS DECAL, TRACTOR OPERATOR SAFETY DECAL, PINCH POINTS DECAL, SHIELD MISSING DECAL, WARNING HOSE BURST DECAL, MULTI HAZZARD DECAL, ALAMO GROUP DECAL, BUZZBAR 62 D138 1 DECAL, BLADE ROTATION DECAL, HEAR PROTECTION REQD DECAL, ROTATING BLADES DECAL, WARNING DISCONNECT DECAL, NO HITCH POST HERE NFS PLATE, SERIAL NUMBER BB NFS METAL, TACK ADAPTER, HYD 20MJ-20FJX DECAL, RED REFLECTOR DECAL, YELLOW REFLECTOR GREASE FITTING NUT, 1"-NC BUSHING BOLT, HEX HEAD 1"-NC X 9" BOLT, HEX HEAD 3/4"-NC KEY, 1/4" SQ KEY 1-1/4" LG PLUG INSERT SHEET, BUZZBAR 2017 Alamo Group Inc. Parts Section -79

84 BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (11-01) & UP (PART 3) 2017 Alamo Group Inc. Parts Section -80

85 BUZZBAR - HEAD ASY - 90 IN 4 BLADE - SN (11-01) & UP (PART 3) Continued VINYL TAPE BLUE 1/2" WIDE VINYL TAPE RED 1/2" WIDE COTTER PIN, 1/8" X WASHER, PLATED MOTOR MOUNT TUBE, MACHINED 2017 Alamo Group Inc. Parts Section -81

86 BUZZBAR - HYD MOTOR - PN MOTOR GEAR ASY SNAP RING * SPACER SEAL RETAINER * SEAL MOUNTING FLANGE W/ BUSHINGS PLUG CHECK ASY * SEAL END * * THRUST PLATE GEAR SET * SQUARE SEAL 2017 Alamo Group Inc. Parts Section -82

87 BUZZBAR - HYD MOTOR - PN Continued DOWEL PIN GEAR HOUSING PORTING FLANGE W/ BUSHINGS WASHER BOLT * SIDE SEAL ( NOT SHOWN ) KEY 2017 Alamo Group Inc. Parts Section -83

88 BUZZBAR - SPINDLE ASY - SN BB & UP SPINDLE ASY, DRIVE SPINDLE (SHOWN) SPINDLE ASY, NON-DRIVE (NOT SHOWN) SPINDLE HOUSING, MACHINED SPINDLE SHAFT, NON-DRIVE SPINDLE SPINDLE SHAFT, DRIVE SPINDLE COLLAR, BEARING PRELOAD BEARING CUP, UPPER OR LOWER BEARING CONE, UPPER OR LOWER 6 15C WASHER, 1-1/4" HARDEND 7 5D NUT, HEX SLOTTED 1-1/4"-12NF PL SEAL, UPPER OR LOWER GREASE FITTING, 1/8" STRAIGHT GREASE RELIEF FITTING, 1-5LBS BOLT, STUD 1/2"-20NF X 1-7/8" COTTER PIN, 3/16 X Alamo Group Inc. Parts Section -84

89 THIS PAGE INTENTIONALLY LEFT BLANK 2017 Alamo Group Inc. Parts Section -85

90 CASTER WHEEL ASY - HD FLAIL BOLT LOCKWASHER FLATWASHER SPACER CASTER ARM RIGHT CASTER ARM LEFT CASTER FORK WELDMENT NUT LOCKWASHER * WHEEL SPACER * WHEEL ASSEMBLY * AXLE BUSHING 2017 Alamo Group Inc. Parts Section -86

91 CASTER WHEEL ASY - HD FLAIL Continued BOLT BUSHING, CASTER ARM GREASE FITTING 2017 Alamo Group Inc. Parts Section -87

92 CHAIN GUARD FRONT & REAR - DOUBLE FRONT, DBL CHAIN GUARD ASY. 60" REAR, DBL CHAIN GUARD ASY. 60" FRONT, DBL CHAIN GUARD ASY. 72" REAR, DBL CHAIN GUARD ASY. 72" FRONT, DBL CHAIN GUARD BRKT WLD`MT, 60" FRONT, DBL CHAIN GUARD BRKT WLD`MT, 72" REAR, DBL.CHAIN GUARD BRKT, 60" REAR, DBL CHAIN GUARD BRKT, 72" CABLE CABLE CLAMP CHAIN ( 8 LINK ) 60" CHAIN 5/16 WLD 8 LINK ZINC PL 83 CHAIN ( 8 LINK ) 72" CLIP ( NOT SHOWN ) BOLT FLATWASHER LOCKNUT 2017 Alamo Group Inc. Parts Section -88

93 CONTROL CONSOLE ASY SUPPORT ARM VALVE MT. WLD`MT ( FOR VERSA DITCHER ) SUPPORT ARM VALVE MT. WLD`MT ( FOR ALL OTHER VALVES ) BOLT LOCKWASHER NUT * FLAT WASHER * LOCKNUT * SOLENOID CUTTER VALVE ASY * PUSH PULL SWITCH * KNOB, SWITCH * BOLT * WIRE HARNESS HEAD RETAINER ASY HEAD RETAINER WLD`MT LOCKWASHER NUT 2017 Alamo Group Inc. Parts Section -89

94 BUMPER KIT - PN WLDMT, BUMPER, TOP, VERSA WLDMT, BUMP SLV, TOP, VRS BUMPER, VERSA, BOTTOM BUMPER, WING RUBBER HHCS 3/8-16UNC 1-1/2 PL NUT HEX 3/8 NC PL HIGH ALLOY, L/W 3/8 YZ NUT,HEX TOPLOCK 3/4 NC GR.C PL HIGH ALLOY, L/W 5/16 YZ KG HHCS 3/4 NC 3-1/2 PL NUT MET 8MM-P Alamo Group Inc. Parts Section -90

95 CONTROL VALVE - 2 SPOOL 2017 Alamo Group Inc. Parts Section -91

96 CONTROL VALVE - 2 SPOOL Continued VALVE DIR CTRL 2-SPOOL PLUG - HEX HD #8MB ADP HYD STGHT 8FB - 8MB ADP HYD TEE 4MJ-4MJ-4FJX ORIFICE,.055 ONE-WAY RESTRCTR ADP HYD ELBOW 8MB-4MJ ADP HYD STGHT 12MB-8MJ ADP, HYD, 12MB - 10MJ ST VINYL TAPE BLUE 1/4" WIDE VINYL TAPE GREEN 1/4" WIDE VINYL TAPE RED 1/2" WIDE VINYL TAPE ORANGE 1/2" WIDE ADP HYD TEE 8MJ-8FJX-8MJ ADP HYD STGHT 4MJ-8FJ VINYL TAPE GREEN 1/2" WIDE VINYL TAPE BLUE 1/2" WIDE ADP HYD ELBOW 8MJ-8FJX ADP HYD STGHT 8MJ-10FJ ADP HYD STGHT 6MB - 4MJ ADJ FLOW CONTROL VALVE ONE-WAY ADP, HYD 6MB - 4FJX STRGHT 2017 Alamo Group Inc. Parts Section -92

97 COUNTERWEIGHT ASY * MOUNT * OIL RESERVOIR ASSEMBLY * COUNTERWEIGHT BOLT LOCKWASHER NUT 2017 Alamo Group Inc. Parts Section -93

98 CUTTER VALVE ASY SOLENOID VALVE AND COIL ASSY ( S/N AND AFTER) SOLENOID VALVE AND COIL ASSY ( S/N AND PRIOR ) SOLENOID VALVE CARTRIDGE W/ SEALS ( S/N AND AFTER ) SOLENOID VALVE CARTRIDGE W/ SEALS ( S/N AND PRIOR ) SOLENOID COIL ( S/N AND AFTER ) SOLENOID COIL ( S/N AND PRIOR ) PILOT PISTON, W/ SEALS RELIEF VALVE SEAL KIT ( RELIEF VALVE ) LOGIC VALVE SEAL KIT ( LOGIC VALVE ) CHECK VALVE SEAL KIT ( CHECK VALVE ) SOLENOID VALVE, SEAL KIT 2017 Alamo Group Inc. Parts Section -94

99 CUTTER VALVE ASY - WITH FITTINGS SOLENOID CUTTER VALVE ASY CUTTER VALVE STRAIGHT ADAPTER WIRE HARNESS SWITCH - PUSH PULL KNOB STRAIGHT ADAPTER 2017 Alamo Group Inc. Parts Section -95

100 CUTTER CONTROL VALVE BLOCK ASY,MANIFOLD,STEEL,DUAL,C-BLOC COIL SOLENOID 12VDC DUAL SPADE SOLENOID, CARTRIDGE 2P3W LOGIC CART, 25 BAR, CUT VAL LOGIC CART, 50 BAR, CUT VAL CARTRIDGE, RELIEF, VALVE, MAIN CARTRIDGE, RELIEF, VALVE,BRAKE A 1 SEAL KIT, COMPLETE SEAL KIT, BLOCK TO PUMP SEAL KIT, POLY, LOGIC VALVE SEAL KIT, VITON, RELIEF VALVE SEAL KIT, VITON, SOL CARTRIDGE 2017 Alamo Group Inc. Parts Section -96

101 CUTTERSHAFT - DRIVE SIDE ASY - 48 IN & 60 IN BOLT CUTTERSHAFT WASHER KEY PULLEY, CUTTERSHAFT BEARING ADAPTER SEAL ROLLER BEARING INNER HOUSING BOLT NUT SEAL HOUSING WLD`MT - 48" HOUSING WLD`MT - 60" SPACER CUTTERSHAFT WLD`MT - 48" CUTTERSHAFT WLD`MT - 60" COTTER PIN RING ( ADD 8 FOR 60" FLAIL ) KNIFE ( ADD 16 FOR PIN ( ADD 8 FOR 60" FLAIL ) 2017 Alamo Group Inc. Parts Section -97

102 CUTTERSHAFT - NON-DRIVE SIDE ASY - 48 IN & 60 IN CUTTERSHAFT WLD`MT CUTTERSHAFT WLD`MT SPACER BEARING ADAPTER SEAL BEARING HOUSING, INNER ROLLER BEARING HOUSING WLD`MT HOUSING WLD`MT WASHER BOLT HOUSING COVER BOLT 2017 Alamo Group Inc. Parts Section -98

103 CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 1) (SN TO CURRENT) FLAIL AXE HEAD ASSY PIN,COTTER 5/32 X 1-1/ Alamo Group Inc. Parts Section -99

104 CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 1) (SN TO CURRENT) Continued NUT,1/2NF CENTERLOCK FLATWASHER 1/2 PL STD HIGH ALLOY, L/W 5/16 YZ KG NUT JAM HEX 5/8 NC PL LOCKNUT TLM 3/8-NC PLC HEXB 5/16 X 1 NC GR CARB 3/8 NC 1-1/4 PL FLATWASHER 5/16 PL HHCS 1/2 NC X 2 GR.5 PL HHCS,5/16-18 X 3/4 PL NUT,HEX TOPLOCK 3/4 NC GR.C PL BOLT 3/8 NC GR8 X 1-1/ HHCS 1/2 NF 1-1/2 PL HEXB 3/4-10UNC 2 PL RUBBER FLAP 6 X 48-1/ CLAMP BAR WLDMT, SKID SHOE ROLLER BEARING AND FLANGE M 1 ROTOR W/KNIVES (FLAIL AXE) A 2 FLANGE BEARING ASY 2 BORE KEY 1/2 X 1/2 X 1 7/8LG LOCKNUT TLM 5/16 NC PLB CARB 5/8-11UNC 3LG PL PULLEY, 3G5V-8.50 DIA BUSHING,QD-HUB SF 1-15/16 DIA WLDMNT, HOUSING, F/AXE 48" WDMT,HITCH POST,FLAIL AXE PLATE,HITCH POST CLAMP PLATE,COVER,BELT & PULLEY 2017 Alamo Group Inc. Parts Section -100

105 CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 2) (SN TO CURRENT) ROD,HINGE,F/A DOOR WLDMNT, DOOR, F/AXE 48" 2017 Alamo Group Inc. Parts Section -101

106 CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 2) (SN TO CURRENT) Continued V-BELT WELDMENT,ROLLER SHSS 3/8-NF X 1-1/2 PL WASHER,2OD,7/16 ID X 3/ WLDMT MOTOR MOUNTS PLATE,INSIDE PLATE HHCS 5/8-11 X 1-1/2 PL HUB,QD-SF 1DIA.BORE W/KEY WAY HYD MOTOR-CAST IRON,3.94 CU IN KEY 1/4 X 1/4 X 1 1/2 LG NUT, JAM 3/8 NF PLB FLATWASHER 5/8 PL STD WASHER,LOCK 5/8 GR8 - YDP 2017 Alamo Group Inc. Parts Section -102

107 CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 1) 2017 Alamo Group Inc. Parts Section -103

108 CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 1) Continued COTTER PIN LOCKNUT TLM 1/2 NC PLC FLATWASHER LOCKWASHER NUT NUT BOLT BOLT BOLT FLATWASHER BOLT NUT LOCKNUT GREASE FITTING BOLT LOCKNUT BOLT BOLT RUBBER FLAP CLAMP BAR SKID SHOE ROLLER BEARING & FLANGE, W/ LOCKING COLLAR M 1 ROTOR (FLAIL AXE) (INCLUDES ITEMS 48-51) A 2 FLANGE BEARING ASSEMBLY KEY LOCKNUT CARRIAGE BOLT PULLEY BUSHING FLAIL AXE HEAD HITCH POST-VERSA PLATE-HITCH POST CLAMP PLATE-COVER, BELT & PULLEY ROD-HINGE, F/A DOOR WELDMENT, DOOR, FLAIL AXE V-BELT ROLLER SOCKET HEAD SET SCREW SKID SHOE WASHER MOTOR MOUNT 2017 Alamo Group Inc. Parts Section -104

109 CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 2) 2017 Alamo Group Inc. Parts Section -105

110 CUTTING HEAD - FLAIL AXE - BELT DRIVE (PART 2) Continued PLATE-INSIDE HUB MOTOR, PISTON STEP KEY JAM NUT BOLT BLADE KIT BUSHING LOCKNUT BUSHING BOLT FLATWASHER LOCKWASHER ROD 2017 Alamo Group Inc. Parts Section -106

111 DEEP DECK ( W-COOLING TUBE ) HYD MOTOR ASY HYDRAULIC MOTOR ELBOW ( RETURN SIDE ) SPLIT FLANGE KIT SPLIT FLANGE KIT ELBOW ( PRESSURE SIDE ) 2017 Alamo Group Inc. Parts Section -107

112 DEEP DECK ( W-O COOLING TUBE ) HYD MOTOR ASY HYDRAULIC MOTOR DEG. ELBOW SPLIT FLANGE KIT FLANGE KIT REDUCER DEG. ELBOW 2017 Alamo Group Inc. Parts Section -108

113 DEEP DECK MOTOR & SPINDLE MOTOR STUD NUT HHCS 1/2 NC 2-1/4 PL BOLT NUT BOLT ( USE WITH BAR ASY. ONLY ) BOLT ( USE WITH PAN ASY. ONLY ) LOCKNUT C 1 SPINDLE ASY SPACER ( USE WITH PAN ASY. ONLY ) PAN ASY BAR ASY Alamo Group Inc. Parts Section -109

114 THIS PAGE INTENTIONALLY LEFT BLANK 2017 Alamo Group Inc. Parts Section -110

115 DEEP DECK MOWER ASY DECK WLD`MT NUT FLATWASHER BOLT 5 2A BOLT SKID SHOE ROLLER WLD`MT ( W/ HEX SHAFT ) NUT CARRIAGE BOLT BEARING ASY BEARING HOUSING BEARING ( W/ HEX BORE ) GREASE FITTING ROLLER MOUNTING BRACKET WLD`MT ( LH ) ROLLER MOUNTING BRACKET WLD`MT ( RH ) REAR FLAP REAR CHAINGUARD ASY FRONT CHAINGUARD ASY FRONT CHAINGUARD BRACKET 2017 Alamo Group Inc. Parts Section -111

116 DEEP DECK MOWER ASY Continued CHAIN 5/16 WLD 8 LINK ZINC PL CHAIN ( 6 LINKS, REAR CHAINGUARD ) CABLE CLAMP CABLE SEAL REAR CHAINGUARD MOUNT 2017 Alamo Group Inc. Parts Section -112

117 DITCHER - BLADE HEAD ASY BLADE HEAD WELDMENT STANDARD BLADE HEAD WELDMENT REVERSE WEAR PLATE LOCKNUT TLM 1/2 NC PLC BOLT MOUNT BRACKET STANDARD MOUNT BRACKET REVERSE BLADE - ROUGH CUT SHIM KIT FOR ROUGH CUT BLADES BOLT BOLT LOCKWASHER NUT 2017 Alamo Group Inc. Parts Section -113

118 DITCHER - BLADE HOUSING HOUSING WLD`MT DEFLECTOR BRKT WLD`MT HINGE PIN FLATWASHER COTTER PIN BACK-UP PLATE WLD`MT BOLT LOCKNUT TLM 1/2 NC PLC CYLINDER PIN, CYLINDER B13 4 HAIR PIN CLIP RUBBER FLAP DEFLECTOR CLAMP BAR FLAP DEFLECTOR BOLT BOLT FLAT SOCKET CAP SCREW COVER HOUSING WLD`MT FLATWASHER 2017 Alamo Group Inc. Parts Section -114

119 DITCHER - BLADE HOUSING ASY - REVERSE ROTATION BLADE HOUSING ASY, ( REVERSE ) BLADE HOUSING WLD`MT ( REVERSE ) DEFLECTOR WLD`MT HINGE PIN FLATWASHER COTTER PIN BACK-UP PLATE WLD`MT ( REVERSE ) BOLT LOCKNUT TLM 1/2 NC PLC CYLINDER CYLINDER PIN B13 - HAIR PIN CLIP * 1 FRONT COVER HOUSING WLD`MT ( REVERSE ) FLAP MOUNT BRACKET RUBBER FLAP RUBBER FLAP CLAMP BAR FLAP DEFLECTOR BOLT BOLT BOLT FLAT SOCKET CAP SCREW 2017 Alamo Group Inc. Parts Section -115

120 DITCHER - BLADE HOUSING ASY - REVERSE ROTATION Continued LOCKNUT FLATWASHER BOLT FLATWASHER LOCKNUT 2017 Alamo Group Inc. Parts Section -116

121 DITCHER - CONTROL VALVE CONTROL VALVE 3 SPOOL SPRING REPAIR KIT H.P. RELIEF VALVE KIT HANDLE ASSEMBLY KIT STRAIGHT ADAPTER ELBOW RISTRICTOR ELBOW PLUG SPOOL REPAIR KIT TEE STRAIGHT ADAPTER 2017 Alamo Group Inc. Parts Section -117

122 DITCHER - DEFLECTOR CYL ASY DEFLECTOR CYLINDER ASY HYDRAULIC CYLINDER GLAND LOCKWIRE ( SEE SEAL KIT ) ROD ASY BARREL WLD`MT PISTON LOCKNUT STRAIGHT ADAPTER CYLINDER PIN HAIR PIN CLIP 2017 Alamo Group Inc. Parts Section -118

123 DITCHER - HEAD ASY BOOM ARM WLDMNT SPINDLE ASY BLADE HOUSING ASY BOLT, HEX HEAD LOCKNUT, TOPLOCK 3/4"-NC GRC PL BLADE HEAD ASY. STD FWD ROTATION BLADE HEAD ASY, OPT REV ROTATION BOLT, HEX HEAD 1/2"-NC X 1-3/4" PL MOTOR, HYD GEAR 15.5 CUIN/REV ADAPTER, HYD ELBOW HOSE #20-20FJX - 20FJX - 122"LG HOSE #20-20FJX - 20MP - 112"LG HOSE CLAMP LOCKNUT TLM 1/2 NC PLC BOLT, HEX HEAD 3/4"NC X 2-1/4" PL GR ADAPTER, HYD ELBOW 20MP - 20MJIC Alamo Group Inc. Parts Section -119

124 DITCHER - HEAD ASY Continued ADAPTER, HYD STGHT 32FL - 20FP FLATWASHER, 3/4" TYPE AW,ZP BOLT, HEX HEAD 3/4"-NC X 2-1/2" PL GR Alamo Group Inc. Parts Section -120

125 DITCHER - HYD MOTOR PARTS - PN MOTOR, GEAR 15.5 CID/REV BODY FLANGE GEAR, DRIVE GEAR GEAR, IDLER GEAR PRESSURE PLATE, (TOP) PRESSURE PLATE, (BOTTOM) SEALING STRIP (INCLUDED IN SEAL KIT ) BACK-UP RING (INCLUDED IN SEAL KIT ) O-RING (INCLUDED IN SEAL KIT & ) SHAFT SEAL (INCLUDED IN SEAL KIT & ) SNAP RING (INCLUDED IN SEAL KIT & ) RETAINER, CHECK VALVE BALL, 1/2" DIA BALL 1/4" DIA BOLT, HEX HEAD WASHER PLUG 2017 Alamo Group Inc. Parts Section -121

126 DITCHER - HYD MOTOR PARTS - PN Continued O-RING (INCLUDED IN SEAL KIT ) DOWEL PIN SHAFT SEAL KIT (INCLUDES ITEMS 10, 11, 12) SEAL KIT (INCLUDES ITEMS 7, 8, 10, 11, 12, 19) BALL BEARING 2017 Alamo Group Inc. Parts Section -122

127 DITCHER - HYD MOTOR PARTS - PN (AFTER ) MOTOR, GEAR 15.5 CID/REV BODY FLANGE GEAR, DRIVE GEAR GEAR, IDLER GEAR PRESSURE PLATE, (TOP) PRESSURE PLATE, (BOTTOM) SEALING STRIP (INCLUDED IN SEAL KIT ) BACK-UP RING (INCLUDED IN SEAL KIT ) O-RING (INCLUDED IN SEAL KIT & ) SHAFT SEAL (INCLUDED IN SEAL KIT & ) SNAP RING (INCLUDED IN SEAL KIT & ) RETAINER, CHECK VALVE BALL, 1/2" DIA BALL 1/4" DIA BOLT, HEX HEAD WASHER PLUG 2017 Alamo Group Inc. Parts Section -123

128 DITCHER - HYD MOTOR PARTS - PN (AFTER ) Continued O-RING (INCLUDED IN SEAL KIT ) DOWEL PIN SHAFT SEAL KIT (INCLUDES ITEMS 10, 11, 12) SEAL KIT (INCLUDES ITEMS 7, 8, 10, 11, 12, 19) 2017 Alamo Group Inc. Parts Section -124

129 DITCHER - HYD SYSTEM - VERSA (PART 1) 2017 Alamo Group Inc. Parts Section -125

130 DITCHER - HYD SYSTEM - VERSA (PART 1) Continued FLANGE KIT IN - TANK FILTER FILTER ELEMENT ADAPTER ELBOW ADAPTER HOSE BIB ELBOW ADAPTER ADAPTER ELBOW PLUG CHECK PLUG ELBOW STRAIGHT ADAPTER PIPE TEE ADAPTER HOSE-TANK TO PUMP HOSE-PUMP TO CUTTER VALVE HOSE-PUMP TO CONTROL VALVE HOSE-FILTER TUBE TO TEE HOSE-CUTTER VALVE TO MOTOR, RETURN HOSE-MOTOR TO CUTTER VALVE, PRESSURE HOSE-CUTTER VALVE TO TEE HOSE-CONTROL VALVE TO TEE HOSE-CONTROL VALVE TO TILT CYLINDER (ROPS UNITS) HOSE-CONTROL VALVE TO TILT CYLINDER (CAB UNITS) HOSE-CONTROL VALVE TO LIFT CYLINDER (ROPS UNITS) HOSE-CONTROL VALVE TO LIFT CYLINDER (CABS UNITS) HOSE CLAMP FILTER RETURN TUBE ADAPTER ELBOW STRAIGHT ADAPTER HOSE-CONTROL VALVE TO DEFLECTOR CYL TEE STRAIGHT ADAPTER HOSE ( ROPS UNITS ) HOSE ( CAB UNITS ) HOSE ( ROPS UNITS ) HOSE ( CAB UNITS ) 2017 Alamo Group Inc. Parts Section -126

131 DITCHER - HYD SYSTEM - VERSA (PART 2) 2017 Alamo Group Inc. Parts Section -127

132 DITCHER - HYD SYSTEM - VERSA (PART 2) Continued HOSE W/ #4 MJ STRAIGHT ADAPTER 2017 Alamo Group Inc. Parts Section -128

133 DITCHER - HYD SYSTEM - VERSA BOOM 2017 Alamo Group Inc. Parts Section -129

134 DITCHER - HYD SYSTEM - VERSA BOOM Continued FLANGE KIT TUBING, TO HYD.RETURN FILTER(VERSA ADAPTER, HYD STGHT 20MP - 20MJ ELBOW, ADAPTER, HYD ELBOW 20MB - 20MJ FITTING, HOSE BIB #24HOSE - #24MP ADAPTER, HYD, ELBOW ADAPTER, HYD STGHT 20MB - 20MJ HOSE, #4-4FJX - 4FJX -184LG FILTER ASY, RETURN IN TANK FILTER ELEMENT ADAPTER, HYD STGHT 12MB - 8MJ TOP FOUR LINKAGE HYD TUBE ADAPTER, HYD ELBOW HOSE, #4-4FJX - 4FJX - 114"LG ADAPTER, HYD ELBOW 4MB - 4MJ HOSE CLAMP, 1-5/16" TO 2-1/ 4" HOSE, #4-4FJX - 4FJX - 80"LG HOSE, #20-20FJX - 20FJX90-52"LG ADAPTER, HYD STGHT 20MB - 20FPX HOSE, #4-4FJX - 4FJX - 200"LG ADAPTER, HYD ELBOW 20MP - 20MJIC TOP FOUR LINKAGE HYD TUBE ADAPTER, HYD STGHT 12MB - 8MJ HOSE, SUCTION #24-84"LG HOSE, #20-20FJX - 20FJX - 70"LG HOSE, #8-8FJX - 8FJX90-108"LG HOSE, #8-8FJX - 8FJX90-56"LG HOSE, #20-20MP - 20MP - 40"LG HOSE, #20-20FJX - 20FJX90-52"LG ADAPTER, HYD ELBOW ADAPTER, HYD ELBOW ADAPTER, HYD STGHT ADAPTER, HYD STGHT 32FL - 20FP 2017 Alamo Group Inc. Parts Section -130

135 DITCHER - SPINDLE ASY SPINDLE HOUSING W/ BEARING CUPS & GREASE FITTING 2& BEARING CONE AND CUP SEAL SPINDLE SPACER NUT GREASE FITTING COUPLING HALF, SPINDLE KEY COUPLING HALF, MOTOR CHAIN, COUPLING SET SCREW RELIEF FITTING 2017 Alamo Group Inc. Parts Section -131

136 THIS PAGE INTENTIONALLY LEFT BLANK 2017 Alamo Group Inc. Parts Section -132

137 EXTENSION ARM ASY * ELBOW * EXTENSION ARM WLD`MT ( HEAVY DUTY ) HOSE ( ROPS UNITS ) HOSE ( CAB UNITS ) * HOSE, W/ # 4MJ HOSE ( ROPS UNITS ) HOSE ( CAB UNITS ) * PIN * CYLINDER * CYLINDER, PIN ( GREASEABLE ) * PIN * PIN * COTTER PIN * LINKAGE ARM WLD`MT * CABLE ASY * SHACKLE WITH SCREW PIN * FLATWASHER * BUSHING * STRAIGHT ADAPTER 2017 Alamo Group Inc. Parts Section -133

138 EXTENSION ARM ASY Continued * LUG BUSHING ( 1/2" LUG ) SPRING TENSION BUSHING BOLT LOCKNUT TLM 1/2 NC PLC PIN, ATTACHMENT ( SPECIAL FOR FLAIL HEAD ONLY ) PIN, ATTACHMENT ( FOR ROTARY HEAD ) * CYLINDER BUSHING * GREASE FITTING * LUG BUSHING PIN HOSE ( ROPS UNITS ) HOSE ( CABS UNITS ) HOSE ( ROPS UNITS ) HOSE ( CABS UNITS ) 2017 Alamo Group Inc. Parts Section -134

139 EXTENSION ARM HVY DTY - SPECIAL 6 IN SHORTER THAN STD * ELBOW * EXTENSION ARM WLD`MT ( HEAVY DUTY ) HOSE ( ROPS UNITS ) HOSE ( CAB UNITS ) 2017 Alamo Group Inc. Parts Section -135

140 EXTENSION ARM HVY DTY - SPECIAL 6 IN SHORTER THAN STD Continued * HOSE ( W/ # 4 MJ ) HOSE ( ROPS UNITS ) HOSE ( CAB UNITS ) * PIN * CYLINDER * CYLINDER, PIN ( GREASEABLE ) * PIN * PIN * COTTER PIN * LINKAGE ARM WLD`MT * CABLE ASSEMBLY * SHACKLE ( W/ SCREW PIN ) * FLATWASHER * BUSHING * STRAIGHT ADAPTER * LUG BUSHING BOLT LOCKNUT TLM 1/2 NC PLC PIN, ATTACHMENT ( SPECIAL FOR FLAIL HEAD ONLY ) PIN, ATTACHMENT ( FOR ROTARY HEAD ONLY ) * CYLINDER BUSHING * GREASE FITTING * LUG BUSHING PIN HOSE ( ROPS UNITS ) HOSE ( CABS UNITS ) HOSE ( ROPS UNITS ) HOSE ( CABS UNITS ) GREASE FITTING, 90 DEG Alamo Group Inc. Parts Section -136

141 FILTER ASY FILTER ASY. ( TUBE STD. LENGTH - 28" ) FILTER ASY. ( TUBE LENGTH - 16" ) FILTER ASY.( TUBE LENGTH - 9" ) FILTER ELEMENT SPRING FILTER BYPASS, VALVE FILTER COVER SEAL KIT ( NOT SHOWN ) NUT (NOT SHOWN) O-RING (NOT SHOWN) 2017 Alamo Group Inc. Parts Section -137

142 THIS PAGE INTENTIONALLY LEFT BLANK 2017 Alamo Group Inc. Parts Section -138

143 FLAIL HEAD ASY - HVY DTY - 48 IN & 60 IN (PART 1) 2017 Alamo Group Inc. Parts Section -139

144 FLAIL HEAD ASY - HVY DTY - 48 IN & 60 IN (PART 1) Continued HD FLAIL WLD`MT - 48" HD FLAIL WLD`MT - 60" CUTTER SHAFT WLD`MT - 48" CUTTER SHAFT WLD`MT - 60" V-BELT QD HUB PULLEY, HYD. MOTOR CUTTER SHAFT WASHER IDLER PIVOT PIN FENDER PULLEY, CUTTER SHAFT BOLT WASHER LOCKWASHER IDLER BEARING SPACER IDLER PULLEY IDLER ARM W/GREASE FITTING SHOE WEAR PLATE ASSEMBLY LOCKNUT TLM 1/2 NC PLC BOLT LOCKWASHER SHOE BOLT SHOE WEAR PLATE TRASH DEFLECTOR PACKAGE ( INCLUDES 18,19,20, & 22 ) - 48" TRASH DEFLECTOR PACKAGE ( INCLUEDS 18,19,20,& 22 ) - 60" TRASH DEFLECTOR - 48" TRASH DEFLECTOR - 60" WASHER ( ADD 2 FOR 60" FLAIL ) NUT ( ADD 2 FOR 60" FLAIL ) BOLT ( ADD 2 FOR 60" FLAIL ) KNIFE PACKAGE COMPLETE ( INCLUDES 24,25,26, & 27 ) - 48" KNIFE PACKAGE COMPLETE ( INCLUDES 24,25,26, & 27 ) - 60" KNIFE ( ADD 16 FOR RING ( ADD 8 FOR 60" FLAIL ) COTTER PIN ( ADD 8 FOR 60" FLAIL ) PIN ( ADD 8 FOR 60" FLAIL ) HYDRAULIC MOTOR ASSEMBLY BOLT WASHER BEARING HOUSING, NON DRIVE BEARING HOUSING, DRIVE 2017 Alamo Group Inc. Parts Section -140

145 FLAIL HEAD ASY - HVY DTY - 48 IN & 60 IN (PART 2) 2017 Alamo Group Inc. Parts Section -141

146 FLAIL HEAD ASY - HVY DTY - 48 IN & 60 IN (PART 2) Continued BOLT, OUTER HOUSING ATTACHMENT NUT, OUTER AND INNER HOUSING - ATTACHMENT HOUSING COVER BOLT, INNER HOUSING AND COVER ATTACHMENT ROLLER BEARING BEARING ADAPTER GREASE FITTING SEAL SEAL BOLT TURNBUCKLE MOTOR BRACKET WELDMENT BOLT NUT COTTER PIN BUMPER TO HEAD ATTACHMENT BOLT-BUMPER NUT HITCH POST ASY BUSHING BOLT NUT ROLLER WLD`MT, W/ HEX SHAFT - 48" ROLLER WLD`MT, W/ HEX SHAFT - 60" ROLLER BEARING & HOUSING ASY. W/ HEX BRG BEARING W/ HEX BRG GREASE FITTING SEAL CARRIAGE BOLT NUT BRACKET LH BRACKET RH SPACER BELT GUARD WELDMENT BOLT BUMPER TO BELT GUARD FLATWASHER LOCKWASHER KEY, COUPLIN ASY KEY, CUTTER SHAFT PULLEY 2017 Alamo Group Inc. Parts Section -142

147 FLAIL HEAD ASY - HVY DTY - 48 IN CUTTERSHAFT WLDMT,CTRSHAFT,50CC /8X3/4 HAMMERLOCK COTTERPN< KNIFE,EXTREME SERVICE RING COMPLETE PIN-HARDENED 2017 Alamo Group Inc. Parts Section -143

148 HYDRAULIC SCHEMATIC HOSE HOSE 2017 Alamo Group Inc. Parts Section -144

149 HYDRO FLOAT OPTION HOSE ELBOW HOSE VALVE STRAIGHT ADAPTOR TEE ACCUMULATOR REDUCER HOSE CLAMP ANGLE PLATE, VALVE CONTROL 2017 Alamo Group Inc. Parts Section -145

150 JOYSTICK CONSOLE ASY 2017 Alamo Group Inc. Parts Section -146

151 JOYSTICK CONSOLE ASY Continued JOYSTICK ASSEMBLY W/ COMPONENTS LED RED 12VDC DECAL JOYSTICK OPERATION CNSLE SWITCH MOMNTRY PUSHBUTTON RED 3A PUSH BUTTON COVER, RED SWITCH MOMNTRY PUSHBUTTON BLK 4A PUSH BUTTON COVER, BLACK SOCKET RELAY RELAY SPDT 12VDC 20A CIRCUIT BREAKER 10A PANEL MNT BOOT CIRCUIT BREAKER COVER CONNECTOR RECEPTACLE 9A PIN, AWG 9B PIN, 12AWG SWITCH ROCKER DPDT W/GREEN LED SWITCH PUSH PULL JOYSTICK ASSEMBLY HANDLE ASSEMBLY DECAL SWITCH OPERATION HANDLE ASSEMBLY PUSHBUTTON FACE PLATE SWITCH MOMENTARY PUSHBUTTON LOCKWASHER - 24 SHELL SIZE NUT, PANEL - 24 SHELL SIZE POTENTIOMETER - SWING POTENTIOMETER - LIFT & DIPPER MACHINE SCREW # /8 LG WASHER #10 NYLON LOCKNUT 8-32 PL TRIGGER SWITCH HARNESS,RESISTOR,DANFOSS VLV 2017 Alamo Group Inc. Parts Section -147

152 KING POST ATTACHMENT - W-PLAIN BUSHING KING PIN W/ PLAIN BUSHING #16, FOR 20`,23`AND 28` BOOMS FRONT TURNING ARM WLD`MT W/ BUSHING # REAR TURNING ARM WLD`MT W/ BUSHING # STEEL BUSHING TURNING ARM PIN (USE W/TEFLON BUSHING) BEARING CUP AND CONE ASY RING, BOTTOM BEARING SEAL RING, TOP BEARING SEAL BEARING SUPPORT COLLAR SEAL SEAL LOCKWASHER NUT 2017 Alamo Group Inc. Parts Section -148

153 KING POST ATTACHMENT - W-PLAIN BUSHING Continued PIN ZERK FITTINGS BUSHING TEFLON IMPREGNATED BUSHING 2017 Alamo Group Inc. Parts Section -149

154 KING POST ATTACHMENT - W-SERRATED BUSHING KING PIN W/ SERRATED BUSHING REAR TURNING ARM WLD`MT W/TEFLON BUSHING FRONT TURNING ARM WLD`MT W/TEFLON BUSHING REAR TURNING ARM WLD`MT W/STEEL BUSHING FRONT TURNING ARM WLD`MT W/STEEL BUSHING STEEL SERRATED BUSHING TURNING ARM PIN-CHROME PLATED-USE ONLY W/TEFLON BUSHING TURNING ARM PIN - GREASEABLE-USE ONLY W/STEEL SERRATED BUSHING BEARING CUP AND CONE ASY RING, BOTTOM BEARING SEAL RING, TOP BEARING SEAL BEARING SUPPORT COLLAR SEAL SEAL LOCKWASHER 2017 Alamo Group Inc. Parts Section -150

155 KING POST ATTACHMENT - W-SERRATED BUSHING Continued NUT PIN GREASE FITTING BUSHING - TEFLON IMPREGNATED - 1-1/4 OD BUSHING - STEEL SERRATED - 1-3/8 OD BUSHING MAIN PIN WLD`MT MAIN PIN WLD`MT-GREASEABLE-USE ONLY W/O GREASE HOLE IN TOP (ITEM #1) 2017 Alamo Group Inc. Parts Section -151

156 LIFT CYLINDER ASY HYDRAULIC CYLINDER GLAND * "O" RING ROD ASY BARREL ASY PISTON LOCKNUT ELBOW PIN WASHER PIN "D" COTTER PIN SEAL KIT * BACK-UP RING (INCLUDED IN SEAL KIT ) * WEAR RING (INCLUDED IN SEAL KIT ) * PISTON SEAL (INCLUDED IN SEAL KIT ) * "O" RING (INCLUDED IN SEAL KIT) 2017 Alamo Group Inc. Parts Section -152

157 LIFT CYLINDER ASY Continued COLLAR SET SCREW * ROD WIPER * "O" RING (INCLUDED IN SEAL KIT) * ROD SEAL * "O" RING (INCLUDED IN SEAL KIT) * BUFFER SEAL * "O" RING (INCLUDED IN SEAL KIT) 2017 Alamo Group Inc. Parts Section -153

158 LIFT CYLINDER P/N A TUBE WLDMT W CYLINDER HEAD THGD PISTON WR PSP ROD WLDMT JRC LOCKNUT TLM 1 NF PL SEAL KIT *O-RING /4 X 3/ 1/2 DURO 90 (INCLUDED IN SEAL KIT ) *SEAL HALLITE 605 ROD 1 1/2 DIA (INCLUDED IN SEAL KIT ) *SEAL WIPER ROD 1.50 SNAP IN (INCLUDED IN SEAL KIT ) *SEAL PSP PISTON RING 3.50 DIA (INCLUDED IN SEAL KIT ) *WEAR RING GFN (INCLUDED IN SEAL KIT ) *THD PROT 7/16-20 UNF PLASTIC (INCLUDED IN SEAL KIT ) *O-RING x.072 D90 BUNA (INCLUDED IN SEAL KIT ) *SEAL BU #236 19PI -236 (INCLUDED IN SEAL KIT ) 2017 Alamo Group Inc. Parts Section -154

159 MOTOR ASY W-FITTINGS - SPLINED HYDRAULIC MOTOR ELBOW SPLIT FLANGE KIT "O" RING 2017 Alamo Group Inc. Parts Section -155

160 THIS PAGE INTENTIONALLY LEFT BLANK 2017 Alamo Group Inc. Parts Section -156

161 MOTOR PARTS - PN & PN (MODEL NO & ) 2017 Alamo Group Inc. Parts Section -157

162 MOTOR PARTS - PN & PN (MODEL NO & ) Continued SNAP RING * "O" RING SEAL RETAINER ( MOTOR ) SEAL RETAINER ( MOTOR ) * SEAL MOUNTING FLANGE W/BUSHINGS PLUG CHECK ASSEMBLY * SEAL END * THRUST PLATE GEAR SET ( MOTOR ) GEAR SET ( MOTOR ) * SQUARE SEAL DOWEL PIN GEAR HOUSING ( MOTOR ) GEAR HOUSING ( MOTOR ) PORTING FLANGE W/BUSHING WASHER BOLT ( MOTOR ) BOLT ( MOTOR ) * SIDE SEAL ( NOT SHOWN ) Seal Kit â Minor Rebuild Includes items 2,4,8,11, Seal Kit â Major Rebuild Includes Items 2,4,8,9,11, Alamo Group Inc. Parts Section -158

163 MOTOR PARTS - PN (MODEL NO ) 2017 Alamo Group Inc. Parts Section -159

164 MOTOR PARTS - PN (MODEL NO ) Continued MOTOR, HYD, GEAR 8.0, HP SEAL HOUSING, SEC HOUSING, PEC HOUSING, GEAR SET, GEAR SHAFT CAP SCREW SCREW, DRIVE PIN, DOWEL THRPL PLUG, ODT (0.25) RTNR, SEAL RING, SNAP "0" RING SEAL, LIP SEAL, LIP SEAL, SQ-R SEAL, SIDE CHAN SEAL, END CHAN SEAL, BK-UP RTNR, SEAL CHECK ASS`Y WASHER SEAL KIT 2017 Alamo Group Inc. Parts Section -160

165 MOTOR PARTS - PN (MODEL NO ) 2017 Alamo Group Inc. Parts Section -161

166 MOTOR PARTS - PN (MODEL NO ) Continued MOTOR,HYD, GEAR, 5.73, HP SEAL HOUSING, SEC HOUSING, PEC HOUSING, GEAR SET, GEAR SHAFT CAP SCREW SCREW, DRIVE PIN, DOWEL THRPL RTNR, SEAL RING, SNAP SEAL,O-R SEAL, LIP SEAL, LIP SEAL, SQ-R SEAL, SIDE SEAL, END SEAL, BACK-UP RTNR, SEAL CHECK ASS`Y WASHER KIT, HP, SEAL, 5.73 CID MOTOR 2017 Alamo Group Inc. Parts Section -162

167 MOUNTING COMPONENTS - COMMON PARTS BOX (OPTION) 2017 Alamo Group Inc. Parts Section -163

168 MOUNTING COMPONENTS - COMMON PARTS BOX (OPTION) Continued LOCKNUT BOLT BOLT BAR, MOUNT STRAP BAR MOUNT ANGLE JOYSTICK CONSOLE ASY (NEW STYLE) WIRE HARNESS 17A ADAPTER, WIRE HARNESS ASSEMBLY JOYSTICK ARM REST BOLT FLATWASHER LOCKNUT FLATWASHER PIVOT PLATE WLDMNT BOLT PLATE, CONSOLE DRAWING, HOSE CONNECTIONS INSERT SHEETS, ELECTRO HYD. CONVERSION DECAL, HOSE CONNECTION PLASTIC TIE LOCKWASHER, HEAVY BOLT DECAL, NOTICE TO OWNER PLASTIC TIE, 15" LONG PLASTIC TIE, 21" LONG A 1 ASSEMBLY A-BOOM OPERATOR & QUICK SPLICE, TO GA PAMPHLET SAFETY MOUNTING FILTER ELEMENT BOOM STOP DECAL, ATTENTION - BOOM SWINGING DECAL, BOOM REST DECAL, PROPER ENGINE OPERATING DECAL, WARNING HOSE BURST L 1 CONTENTS LIST DECAL, MULTI HAZARD INSTRUCTION DRAWING BOOKLET, A-BOOM PAINT, SPRAY CAN YELLOW PLASTIC TIE, 7" LONG T 1 MANUAL, TECHNICAL SERVICE, A-BOOM RUBBER GROMMET, 2-1/4" HOLE 2017 Alamo Group Inc. Parts Section -164

169 OIL RESERVOIR ASY TANK WLD`MT ( TANK WILL VARY W/ TRACTOR MODELS ) SUCTION FILTER BOLT ELBOW SPRING NUT SUCTION PIPE WLD`MT ( PIPE LENGTH VARIES W/ TANK WLD`MTS ) ELBOW HOSE BIB FILLER CAP WELDMENT FILLER CAP BREATHER CAP SIGHT GAUGE MAGNETIC PLUG GASKET - RUBBER GASKET - CORK FILTER REPLACEMENT ELEMENT NUT GASKET - RUBBER GASKET - CORK ADAPTER 2017 Alamo Group Inc. Parts Section -165

170 OIL RESERVOIR ASY Continued FLATWASHER BOLT NUT HOSE CLAMP LOCKWASHER FILTER RETURN TUBE ( LENGTH VARIES W/ TANK WLD`MTS ) NUT BOLT PUSHNUT TUBE CLAMP O-RING DIAL INDICATOR NOTE:BREATHER CAP DEPENDANT ON IF UNDER EXTERNAL TANK 2017 Alamo Group Inc. Parts Section -166

171 PUMP ASY - SINGLE FRONT - PN FRONT PUMP ASY HYDRAULIC PUMP DEG. ELBOW FLANGE KIT HOSE BIB HOSE CLAMP 2017 Alamo Group Inc. Parts Section -167

172 PUMP ASY - SINGLE REAR - PN PUMP ASSY 540 PTO 1-1/ HYDRAULIC PUMP DEG. ELBOW FLANGE KIT HOSE BIB HOSE CLAMP ELBOW 2017 Alamo Group Inc. Parts Section -168

173 PUMP ASY - TANDEM FRONT - PN FRONT TANDEM PUMP ASY HYDRAULIC PUMP DEG. ELBOW DEG. ELBOW FLANGE KIT HOSE BIB HOSE CLAMP 2017 Alamo Group Inc. Parts Section -169

174 PUMP ASY - TANDEM FRONT W- 1-I/4 IN FLANGE - PN * FRONT TANDEM PUMP ASY.- W/ 1-1/4 FLANGE HYDRAULIC PUMP DEG. ELBOW DEG. ELBOW FLANGE KIT HOSE BIB HOSE CLAMP FLANGE KIT STRAIGHT ADAPTER 2017 Alamo Group Inc. Parts Section -170

175 PUMP ASY - TANDEM REAR - PN REAR TANDEM PUMP ASY HYDRAULIC PUMP DEG. ELBOW DEG. ELBOW FLANGE KIT HOSE BIB HOSE CLAMP ELBOW 2017 Alamo Group Inc. Parts Section -171

176 PUMP PARTS - SINGLE FRONT - PN BOLT WASHER PORTING FLANGE W/ BUSHING * SEAL MOUNTING FLANGE W/ BUSHINGS PLUG GEAR HOUSING * SEAL END * THRUST PLATE GEAR SET * SQUARE SEAL DOWEL PIN SEAL KIT MINOR REBUILD INCLUDES ITEMS 4,8, SEAL KIT â MAJOR REBUILD INCLUDES ITEMS 4,8,9, Alamo Group Inc. Parts Section -172

177 PUMP PARTS - SINGLE REAR - PN REAR, SINGLE PUMP ASY BOLT WASHER PORTING FLANGE W/ BUSHING * SEAL MOUNTING FLANGE W/ BUSHINGS PLUG GEAR HOUSING * SEAL END * THRUST PLATE GEAR SET * SQUARE SEAL DOWEL PIN 2017 Alamo Group Inc. Parts Section -173

178 THIS PAGE INTENTIONALLY LEFT BLANK 2017 Alamo Group Inc. Parts Section -174

179 PUMP PARTS - TANDEM FRONT - PN FRONT, TANDEM PUMP * SEAL MOUNTING FLANGE W/ BUSHINGS PLUG * SEAL END GEAR SET DOWEL PIN GEAR HOUSING * SQUARE SEAL BEARING CARRIER HOUSING W/ BUSHINGS GEAR SET CONNECTOR SHAFT GEAR HOUSING * THRUST PLATE END FLANGE W/ BUSHING WASHER STUDS NUTS 2017 Alamo Group Inc. Parts Section -175

180 PUMP PARTS - TANDEM FRONT - PN Continued SEAL KIT MINOR REBUILD INCLUDES ITEMS 1,4, SEAL KIT MAJOR REBUILD INCLUDES ITEMS 1,4,8, Alamo Group Inc. Parts Section -176

181 PUMP PARTS - TANDEM FRONT - PN SEAL MOUNTING FLANGE W/BUSHINGS PLUG SEAL END GEAR SET DOWEL PIN GEAR HOUSING SQUARE SEAL BEARING CARRIER HOUSING W/BUSHINGS GEAR SET CONNECTOR SHAFT GEAR HOUSING THRUST PLATE END FLANGE W/BUSHING WASHER 2017 Alamo Group Inc. Parts Section -177

182 PUMP PARTS - TANDEM FRONT - PN Continued STUDS NUTS SEAL KIT MINOR REBUILD KIT INCLUDES 1,4, SEAL KIT MAJOR REBUILD KIT INCLUDES 1,4,8, Alamo Group Inc. Parts Section -178

183 PUMP REPAIR PARTS - TANDEM REAR - PN REAR, TANDEM PUMP * SEAL MOUNTING FLANGE W/BUSHINGS PLUG * SEAL END GEAR SET DOWEL PIN GEAR HOUSING * SQUARE SEAL BEARING CARRIER HOUSING W/BUSHINGS GEAR SET CONNECTOR SHAFT GEAR HOUSING * THRUST PLATE END FLANGE W/BUSHING WASHER STUDS NUTS SEAL KIT MINOR REBUILD INCLUDES ITEMS 1,4, SEAL KIT MAJOR REBUILD INCLUDES ITEMS 1,4,8, Alamo Group Inc. Parts Section -179

184 SKID SHOE EXTENSION KIT KIT- SKID SHOE EXT- VERSA KIT- SKID SHOE EXT-VERSA SKID SHOE WLD`MT - RH - 60" SKID SHOE WLD`MT - RH - 72" SKID SHOE WLD`MT - LH - 60" SKID SHOE WLD`MT - LH - 72" BOLT FLATWASHER LOCKNUT BOLT SKID SHOE - 60" SKID SHOE SPACER BOLT BLADE BAR SPACER BOLT 2017 Alamo Group Inc. Parts Section -180

185 SPEED INCREASER - PN (ALUMINUM HSG) 2017 Alamo Group Inc. Parts Section -181

186 SPEED INCREASER - PN (ALUMINUM HSG) Continued HOUSING GASKET GASKET FLANGE PLUG GASKET PLUG LOCKWASHER BOLT LOCKWASHER BOLT DOWEL HOUSING GASKET FLANGE GASKET DIPSTICK GASKET PLUG SEAL BEARING RETAINING RING BEARING SHAFT KEY GEAR (540 RPM) GEAR (1000 RPM) PINION (540 RPM) PINION (1000 RPM) SPACER PUMP FLANGE SPLINED PUMP ADAPTER 2017 Alamo Group Inc. Parts Section -182

187 SPEED INCREASER - PN (STEEL HSG) 2017 Alamo Group Inc. Parts Section -183

188 SPEED INCREASER - PN (STEEL HSG) Continued SPEED INCREASER ASSEMBLY ADAPTER, SHAFT SHAFT & GEAR, LOW SPEED PUMP FLANGE COVER, CLOSED COVER, OPEN PIPE PLUG SEAL RETAINING RING BREATHER BEARING CUP BEARING CONE BEARING CUP BEARING CONE SPACER RING HOUSING HOUSING DOWEL GASKET (.015 ) SPACER RING NAME TAG SHIM (.005 ALUM. ) SHIM (.007 ALUM. ) SHIM (.020 ALUM. ) SHIM (.005 ALUM. ) SHIM (.007 ALUM. ) SHIM (.020 ALUM. ) SCREW LOCKWASHER SCREW NUT LOCKWASHER 2017 Alamo Group Inc. Parts Section -184

189 SPINDLE & HOUSING ASY B - ASSY,SPINDLE HOUSING-SPLINED MACH, CAST, SPINDLE, HOUSING SPINDLE -SPLINED BEARING RING SEAL SNAP RING SPINDLE CUP & CONE ASY BEARING,ROLLER-50 X 90 X LOCKNUT-SPINDLE BEARING 2017 Alamo Group Inc. Parts Section -185

190 SPINDLE & HOUSING ASY Continued GREASE RELIEF FITTING 1-5LBS FITTING,GREASE 1/8 MP STRAIGHT COVER 2017 Alamo Group Inc. Parts Section -186

191 SPINDLE HOUSING & SPINDLE ASY C - SPLINED SPINDLE ASY C 1 HOUSING SPINDLE BEARING RING SEAL SNAP RING BEARING BEARING LOCKWASHER NUT PLUG PRESSURE RELIEF PLUG REDUCER 2017 Alamo Group Inc. Parts Section -187

192 SPINDLE HOUSING & SPINDLE ASY - PN C C 1 HOUSING SPINDLE BEARING RING SEAL SNAP RING SPINDLE CUP & CONE ASY BEARING LOCKWASHER NUT PLUG PRESSURE RELIEF PLUG REDUCER 2017 Alamo Group Inc. Parts Section -188

193 SWING CYLINDER ASY B - CYLINDER, W/O FITTINGS SWING CYLINDER ASY, W/ FITTINGS ADAPTER, ELBOW TEFLON BEARING CYLINDER PIN WLD`MT COTTER PIN CYLINDER TUBE WLD`MT CYLINDER HEAD PISTON ROD WLD`MT 10 5JRC LOCKNUT WASHER PIN DEAD END CYLINDER 13 *** 1 O-RING? 14 *** 1 ROD SEAL? 15 *** 1 ROD WIPER SEAL? 16 *** 1 PISTON RING SEAL 17 *** 1 WEAR RING? 18 *** 1 SEAL? SEAL KIT (ITEMS 13 THRU 18 W/ *** ARE INCLUDED IN SEAL KIT) 2017 Alamo Group Inc. Parts Section -189

194 TAIL WHEEL ASY TAILWHEEL TUBE BOLT LOCKNUT COLLAR BOLT NUT CASTER FORK BOLT BEARING SPACER BEARING ASY. ( CUP & CONE ) SEAL TIRE W/ RIM, HUB & CUPS NUT,TOPLOCK 5/8 NC PLC 2017 Alamo Group Inc. Parts Section -190

195 TILT CYLINDER ASY A - CYLINDER ASY TUBE WLD`MT CYLINDER HEAD PISTON ROD WLD`MT SEAL KIT *O-RING (INCLUDED IN SEAL KIT ) *ROD WIPER SEAL (INCLUDED IN SEAL KIT ) *PISTON RING SEAL (INCLUDED IN SEAL KIT ) *WEAR RING (INCLUDED IN SEAL KIT ) 25 5JRC LOCKNUT *SEAL (INCLUDED IN SEAL KIT ) *ROD HALLITE SEAL (INCLUDED IN SEAL KIT ) 2017 Alamo Group Inc. Parts Section -191

196 TILT CYLINDER ASY - VERSA EXTENSION ARM HYDRAULIC CYLINDER GLAND * "O" RING ROD ASY BARREL ASY PISTON LOCKNUT ADAPTER PIN "E" SEAL KIT PIN, GREASEABLE BREATHER PLUG COTTER PIN * BACK-UP RING * "O" RING (INCLUDED IN SEAL KIT) COLLAR * WEAR RING * "O" RING (INCLUDED IN SEAL KIT) * PISTON SEAL * "O" RING (INCLUDED IN SEAL KIT) * BUFFER SEAL * "O" RING (INCLUDED IN SEAL KIT) 2017 Alamo Group Inc. Parts Section -192

197 TILT CYLINDER ASY - VERSA EXTENSION ARM Continued SET SCREW * "O" RING (INCLUDED IN SEAL KIT ) * ROD WIPER (INCLUDED IN SEAL KIT ) * ROD SEAL (INCLUDED IN SEAL KIT ) 2017 Alamo Group Inc. Parts Section -193

198 TIMBERCAT HEAD ASY (PART 1) 2017 Alamo Group Inc. Parts Section -194

199 TIMBERCAT HEAD ASY (PART 1) Continued TIMBERCAT ASY. - 5` TIMBERCAT ASY. - 7` BOTTOM BLADE - 5` BOTTOM BLADE - 7` TOP BLADE - 5` TOP BLADE - 7` SLIDE BEARING - 5` SLIDE BEARING - 7` FRONT COVER - 5` FRONT COVER - 7` BOLT BOLT - 5" BOLT - 7" BUSHING - 5` BUSHING - 7` WASHER - 5` WASHER - 7` LOCKNUT - 5` LOCKNUT - 7` GREASE FITTING - 5` GREASE FITTING - 7` TIMBERCAT FRAME BOLT LOCKWASHER VALVE MOUNT PLATE BOLT LOCKWASHER INVERSION VALVE BOLT LOCKNUT CYLINDER PIN COTTER PIN WASHER CYLINDER MOUNT BOLT SPRING ADJUSTING BOLT NUT LOCKNUT JAMNUT 2017 Alamo Group Inc. Parts Section -195

200 TIMBERCAT HEAD ASY (PART 2) 2017 Alamo Group Inc. Parts Section -196

201 TIMBERCAT HEAD ASY (PART 2) Continued COVER HITCH POST ( A-BOOM ) BOLT FLOW DIVIDER ADAPTER - 45 DEG NUT,TOPLOCK 5/8 NC PLC BOLT BRACKET NUT SELF TAPPING SCREW WASHER PIN GREASE FITTING BUSHING BUSHING BOLT BOLT NUT HOSE HOSE HOSE HOSE ADAPTER - STRAIGHT ADAPTER - 90 DEG PLUG ADAPTER - 90 DEG ADAPTER - STRAIGHT ADAPTER - SPECIAL ADAPTER - 90 DEG ADAPTER - 90 DEG HOSE HOSE W/ 90 DEG ADAPTER - 90 DEG HOSE SLEEVING ADHESIVE KIT 2017 Alamo Group Inc. Parts Section -197

202 VALVE - BOOM CONTROL - 4 SPOOL VALVE ASSEMBLY ADAPTER ADAPTER DETENT KIT ( STANDARD ) VALVE SECTION - INLET COVER VALVE SECTION - SWING VALVE SECTION - LIFT VALVE SECTION - DIPPER VALVE SECTION - TILT VALVE SECTION - OUTLET COVER HANDLE LINKAGE REPAIR KIT NUT LOCKWASHER BOLT KIT, BOLTS, NUTS AND SEALS NUT * O-RING KIT DETENT KIT - FLOAT ( INCL. # 26 ) RELIEF CARTRIDGE ( SET AT 875 PSI ) MAIN RELIEF VALVE SEAL KIT RELIEF CARTRIDGE ( SET AT 1500 PSI ) 2017 Alamo Group Inc. Parts Section -198

203 VALVE - BOOM CONTROL - 4 SPOOL Continued LOAD CHECK PLUG ASY ( 2000 PSI ) MAIN RELIEF ( SET AT 2500 PSI ) DETENT CAP ONLY RELIEF CARTRIDGE ( SET AT 2000 PSI ) RESTRICTOR ASSEMBLY ( NOT SHOWN ) SEAL KIT FOR RELIEF CARTRIDGES ONE WAY RESTRICTOR RELIEF CARTRIDGE ( SET AT 2500 PSI ) NOTE:PART NUMBER KIT CONTAINS 3 BOLTS, 3 NUTS & 14 WASHERS 2017 Alamo Group Inc. Parts Section -199

204 VALVE ASSEMBLY - 4 SPOOL FIXED DISPLACEMENT (OPTION) 2017 Alamo Group Inc. Parts Section -200

205 VALVE ASSEMBLY - 4 SPOOL FIXED DISPLACEMENT (OPTION) Continued VALVE ASSEMBLY OCFD ASSEMBLY, VALVE - 4 SPOOL STRAIGHT ADAPTER PLASTIC CAP STRAIGHT ADAPTER STRAIGHT ADAPTER STRAIGHT ADAPTER STRAIGHT ADAPTER ELBOW ORIFICE,.063 ONE WAY RESTRICTOR ORIFICE,.070 ONE WAY RESTRICTOR ORIFICE,.055 ONE WAY RESTRICTOR VALVE ASSEMBLY, SOLENOID LOCK PLASTIC CAP SECTION ASY, SWING, LIFT OR DIPPER SECTION ASY, TILT SPOOL, SWING SPOOL, LIFT SPOOL, DIPPER SPOOL, TILT SECTION, INLET OCFD VALVE SECTION, END OCFD VALVE 2017 Alamo Group Inc. Parts Section -201

206 VALVE ASSEMBLY - 5 SPOOL FIXED DISPLACEMENT (OPTION) 2017 Alamo Group Inc. Parts Section -202

207 VALVE ASSEMBLY - 5 SPOOL FIXED DISPLACEMENT (OPTION) Continued VALVE ASSEMBLY, OCFD ASSEMBLY, VALVE - 5 SPOOL STRAIGHT ADAPTER PLASTIC CAP STRAIGHT ADAPTER STRAIGHT ADAPTER STRAIGHT ADAPTER STRAIGHT ADAPTER ELBOW ORIFICE,.063 ONE WAY RESTRICTOR ORIFICE,.070 ONE WAY RESTRICTOR ORIFICE,.055 ONE WAY RESTRICTOR VALVE ASSEMBLY, SOLENOID LOCK PLASTIC CAP SECTION ASY, SWING, LIFT OR DIPPER SETION ASY, TILT SECTION ASY, DOOR SPOOL, SWING OR DOOR SPOOL, LIFT SPOOL, DIPPER SPOOL, TILT SECTION, INLET OCFD VALVE SECTION, END OCFD VALVE 2017 Alamo Group Inc. Parts Section -203

208 VALVE ASSEMBLY - OCFD SYS 4 SPOOL (OPTION) ELECTRICAL ACTIVATION MODULE ELECTRICAL ACTIVATION MODULE SEAL KIT O RINGS (BETWEEN THE MECHANICAL ACTIVATION MODULE SEAL KIT O RINGS BETWEN HANDLE GASKET,CONNECTOR TO MODULE KIT, TIE ROD, 4-SPOOL RELIEF VALVE 2755 PSI RELIEF VALVE 2755 PSI(PRE4/98) RELIEF VALVE 2030 PSI RELIEF VALVE 2030 PSI(PRE4/98) SHCS METRIC 6-P1.0-33MM RELIEF VALVE 1160 PSI 2017 Alamo Group Inc. Parts Section -204

209 VALVE ASSEMBLY - OCFD SYS 4 SPOOL (OPTION) Continued RELIEF VALVE 1160 PSI(PRE4/98) SECTION,BARE,SWING,LIFT,DIPPER SECTION,BARE, TILT SECTION,BARE, DOOR SPOOL, SWING DOOR SPOOL, LIFT SPOOL, DIPPER SPOOL, TILT SECTION, END CAP SECTION INLET/OUTLET OCFD SEAL KIT, O-RING VALVE SECTION 2017 Alamo Group Inc. Parts Section -205

210 VALVE ASSEMBLY - OCFD SYS 5 SPOOL (OPTION) ELECTRICAL ACTIVATION MODULE ELECTRICAL ACTIVATION MODULE SEAL KIT O RINGS (BETWEEN THE MECHANICAL ACTIVATION MODULE SEAL KIT O RINGS BETWEN HANDLE GASKET,CONNECTOR TO MODULE KIT,VALVE ASSEMBLY - 5 SPOOL RELIEF VALVE 2755 PSI RELIEF VALVE 2755 PSI(PRE4/98) RELIEF VALVE 2030 PSI RELIEF VALVE 2030 PSI(PRE4/98) SHCS METRIC 6-P1.0-33MM RELIEF VALVE 1160 PSI 2017 Alamo Group Inc. Parts Section -206

211 VALVE ASSEMBLY - OCFD SYS 5 SPOOL (OPTION) Continued RELIEF VALVE 1160 PSI(PRE4/98) SECTION,BARE,SWING,LIFT,DIPPER SECTION,BARE, TILT SECTION,BARE, DOOR SPOOL, SWING DOOR SPOOL, LIFT SPOOL, DIPPER SPOOL, TILT SECTION INLET/OUTLET OCFD SECTION, END CAP SEAL KIT, O-RING VALVE SECTION RELIEF, MAIN 2700 PSI 2017 Alamo Group Inc. Parts Section -207

212 VALVE BANK COVER HANDLE VALVE COVER SPACER TUBE LOCKNUT BOLT HANDLE VALVE OPERATION DECAL 2017 Alamo Group Inc. Parts Section -208

213 VALVE COVER INSTALLATION HANDLE VALVE COVER ( FOR OLD STYLE VALVE ) HANDLE VALVE COVER SHORT SPACER TUBE LONG SPACER TUBE NUT BOLT BOLT FLATWASHER 2017 Alamo Group Inc. Parts Section -209

214 VALVE REMOTE CONTROL 2017 Alamo Group Inc. Parts Section -210

215 VALVE REMOTE CONTROL Continued BRACKET, ARM REST MOUNT PLATE, MOUNT EXTENSION BRACKET, PIVOT PLATE MOUNT SWITCH MOUNT WLD`MT SINGLE AXIS CONTROL STICK ASY ARM REST ASY BRACKET-VALVE CONNECT WLD`MT BOLT ( DUAL AXIS & 2-HANDLE ) BOLT ( 3-HANDLE ) BOLT ( 4-HANDLE ) FLAT WASHER BOLT BOLT BOLT FLATWASHER BOLT LOCKNUT LOCKNUT LOCKNUT CABLE CONNECT KIT - DITCHER VALVE JAMNUT SWITCH, PUSH PULL KNOB PIVOT PLATE WLD`MT DECAL, ON/OFF SWITCH KNOB, VALVE HANDLE WIRE HARNESS KIT ( NOT SHOWN ) 2017 Alamo Group Inc. Parts Section -211

216 VALVE SEGMENT - INDIVIDUAL SEGMENT - NON-FLOAT POSITIONER SEE VALVE BANK FOR PART # * SEAL KIT FOR RELIEF CARTRIDGE * O-RING KIT * WASHER AND O-RING 2017 Alamo Group Inc. Parts Section -212

217 VALVE SEGMENT - INDIVIDUAL SEGMENTS - FLOAT POSITIONER, FLOAT SEE VALVE BANK FOR PART # ON LOAD CHECK OR WORK PORT RELIEF SEAL KIT FOR RELIEF CARTRIDGE * O-RING KIT WASHER AND O-RING O-RING ( INCLUDED IN SEAL KIT # ) O-RING ( INCLUDED IN SEAL KIT # ) 2017 Alamo Group Inc. Parts Section -213

218 VERSA BOOM INSERT ASY * VERSA BOOM INSERT * BASIC TRACTOR MT. WLD`MT PIN BOLT LOCKNUT TLM 1/2 NC PLC BOLT LOCKNUT NUT * KING POST ASSEMBLY ( SEE PAGE 6-85 ) SWING CYLINDER PIN COTTER PIN WASHER TURNING ARM PIN STOP - REAR SWING STOP - FRONT SWING BOLT LOCKNUT TLM 1/2 NC PLC BUSHINGS 2017 Alamo Group Inc. Parts Section -214

219 VERSA FLAIL & FLAIL AXE - HYD MOTOR ASY - P/N HYDRAULIC MOTOR ELBOW SPLIT FLANGE KIT 2017 Alamo Group Inc. Parts Section -215

220 VERSA FLAIL & FLAIL AXE - HYD MOTOR REPAIR PARTS - P/N Alamo Group Inc. Parts Section -216

221 VERSA FLAIL & FLAIL AXE - HYD MOTOR REPAIR PARTS - P/N Continued HOUSING, SEC HOUSING, PEC GEAR HOUSING GEAR SET CAP SCREW KEY 1/4 X 1/4 X 1 1/2 LG USE **THRPL PLUG HEX SKT HD 4MB RETAINER SEAL RING, RETAINING, INTERNAL *O-RING *SEAL, BK-UP *SEAL, END *SEAL, SIDE *LIP SEAL *SEAL, DIRT EXCLUDER *SEAL, SQ-R SPACER CHECK ASSEMBLY WASHER KIT-SEAL-MAJOR REBUILD FOR KIT-SEAL-MINOR REBUILD FOR 2017 Alamo Group Inc. Parts Section -217

222 VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 1) 2017 Alamo Group Inc. Parts Section -218

223 VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 1) Continued VERSA FLAIL, 60" W/CC KNIVES VERSA FLAIL, 60" W/ES KNIVES QD HUB BOLT MOTOR PULLEY MOTOR PLATE BOLT LOCKNUT MOTOR ASY. W/ FITTINGS HYD MOTOR-CAST IRON,FLAIL HD ADAPTER, HYD, ELBOW SPLIT FLANGE KIT # HOSE #20-20FJX -20FJX - 84LG HOSE #20-20FJX -20FJX - 88LG CORDURA SLEEVING -69 INCHES PKG, 62" TRASH DEFLECTOR( REAR) DEFLECTOR,TRASH,62" (REAR) FLATWASHER LOCKNUT BOLT CTRHSG WLD`MT,60" VERSA-FLAIL RUBBER BUMPER FLAT HEAD BOLT LOCKNUT SPRING,EXTENSION BOLT HEX NUT IDLER PIVOT PIN FLATWASHER COTTER PIN RH IDLER ARM ASY, (FWD ROT) RH IDLER ARM WLD`MT, (FWD ROT) IDLER PULLEY IDLER BEARING SPACER CUTTERSHAFT PULLEY CUTTERSHAFT WASHER BOLT BELT COVER WLD`MT BOLT LOCKNUT FLATWASHER 2017 Alamo Group Inc. Parts Section -219

224 VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 2) 2017 Alamo Group Inc. Parts Section -220

225 VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 2) Continued V-BELTS MATCHED PAIR (2 BELTS) SHOE WEAR PLATE, W/ BOLTS PKG SHOE/WEAR PLATE LOCKNUT TLM 1/2 NC PLC CARRIAGE BOLT 2A PLOW BOLT KEY CUTTERSHAFT BEARING ASY, DRIVE SIDE HHCS 3/8 NF 1-1/8 PL LOCKWASHER, 3/8 EXTERNAL TOOTH CUTTERSHAFT BEARING ASY, NON-DRIVE BOLT 3/8 NC GR8 X 1-1/ LOCKNUT TLM 3/8-NC PLC BEARING CUTTERSHAFT TWO WAY KNIFE PKG 50 DEG EXT. SERVICE KNIFE PKG FENDER CUTTERSHAFT WLD`MT,60" CUTTERSHAFT, W/CC KNIVES CUTTER SHAFT, W/ES KNIVES ROLLER MOUNTING WLD`MT ROLLER BRG ASY. W/HEX BORE LOCKNUT CARRIAGE BOLT ROLLER BRG SEAL LH ROLLER BRKT ASY. W/HEX BRG RH ROLLER BRKT ASY. W/HEX BRG GREASE FITTING CARRIAGE BOLT LOCKNUT TLM 1/2 NC PLC ROLLER WLD`MT, 62" W/HEX SHAFT SQUARE KEY FOOT GUARD WLD`MT,60" BOLT LOCKWASHER FLATWASHER FLATWASHER HEX NUT BOLT NUT,TOPLOCK 5/8 NC PLC BOLT 2017 Alamo Group Inc. Parts Section -221

226 VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 3) 2017 Alamo Group Inc. Parts Section -222

227 VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 3) Continued LOCKNUT BOLT BOLT WLDMNT, HEAD RETAINER PIN - VERSA FLAIL MOUNT BOLT BAR FLAP RETAINER, 62" REAR LOCKNUT TLM 1/2 NC PLC CARRIAGE BOLT WASHER TYRONE LOCKWASHER FLATWASHER FLAIL CUTTERHSG ASY, 60CC(60ES LOCKWASHER LOCKNUT NO. 2 RED LUBRICAPS BOLT BOLT LOCKWASHER LOCKWASHER BOLT BOLT BOLT BOLT DECAL, OPERATING INSTRUCTIONS DECAL, GREASE FITTING INSIDE DECAL, DANGER-MULTI HAZARD DECAL, FRONT SHIELD REMOVAL DECAL, WARNING SHIELDS & GUARDS DECAL, WARNING OIL LEAK DECAL, ALAMO GROUP DECAL, WARNING BELT SHIELD DECAL, REPLACEMENT PARTS DECAL, DANGER BOOM FLAILS DECAL, THROWN OBJECTS DECAL, RED REFLECTOR DECAL, YELLOW REFLECTOR DECAL, ALAMO IND. GREEN & BLACK DECAL, ALAMO IND. GREEN & BLACK DECAL, HEIGHT ADJUSTMENT PLASTIC TIE-ON 15 LG 2017 Alamo Group Inc. Parts Section -223

228 VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 4) 2017 Alamo Group Inc. Parts Section -224

229 VERSA FLAIL ASY - 60 IN PN & PN SN & UP (PART 4) Continued /16X 7 PLASTIC TIE WRAP SUPPLEMENT INST.INSTRUCTIONS DWG INST BLADE PIN AB Alamo Group Inc. Parts Section -225

230 VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 1) 2017 Alamo Group Inc. Parts Section -226

231 VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 1) Continued VERSA FLAIL, 74" W/CC KNIVES VERSA FLAIL, 74" W/ES KNIVES QD HUB BOLT MOTOR PULLEY MOTOR PLATE BOLT LOCKNUT MOTOR ASY. W/ FITTINGS HYD MOTOR-CAST IRON,FLAIL HD ADAPTER, HYD, ELBOW SPLIT FLANGE KIT # HOSE #20-20FJX -20FJX - 84LG HOSE #20-20FJX -20FJX - 88LG CORDURA SLEEVING - 69 INCHES DEFLECTOR, TRASH, 74" (REAR) FLATWASHER LOCKNUT BOLT CTRHSG WLD`MT,74" VERSA-FLAIL RUBBER BUMPER FLAT HEAD BOLT LOCKNUT SPRING,EXTENSION BOLT HEX NUT IDLER PIVOT PIN FLATWASHER COTTER PIN RH IDLER ARM ASY, (FWD ROT) RH IDLER ARM WLD`MT, (FWD ROT) IDLER PULLEY IDLER BEARING SPACER CUTTERSHAFT PULLEY CUTTERSHAFT WASHER BOLT BELT COVER WLD`MT BOLT LOCKNUT FLATWASHER V-BELTS MATCHED PAIR (2 BELTS) 2017 Alamo Group Inc. Parts Section -227

232 VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 2) 2017 Alamo Group Inc. Parts Section -228

233 VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 2) Continued V-BELTS MATCHED PAIR (2 BELTS) SHOE WEAR PLATE, W/ BOLTS PKG SHOE/WEAR PLATE LOCKNUT TLM 1/2 NC PLC CARRIAGE BOLT 2A PLOW BOLT KEY CUTTERSHAFT BEARING ASY, DRIVE SIDE HHCS 3/8 NF 1-1/8 PL LOCKWASHER,3/8 EXTERNAL TOOTH CUTTERSHAFT BEARING ASY, NON-DRIVE BOLT 3/8 NC GR8 X 1-1/ LOCKNUT TLM 3/8-NC PLC BEARING CUTTERSHAFT TWO WAY KNIFE PKG 50 DEG EXT. SERVICE KNIFE PKG FENDER CUTTERSHAFT WLD`MT,74" CUTTERSHAFT, W/CC KNIVES CUTTER SHAFT, W/ES KNIVES ROLLER MOUNTING WLD`MT ROLLER BRG ASY. W/HEX BORE LOCKNUT CARRIAGE BOLT ROLLER BRG SEAL LH ROLLER BRKT ASY. W/HEX BRG RH ROLLER BRKT ASY. W/HEX BRG GREASE FITTING CARRIAGE BOLT LOCKNUT TLM 1/2 NC PLC ROLLER WLD`MT, 74" W/HEX SHAFT SQUARE KEY FOOT GUARD WLD`MT,74" BOLT LOCKWASHER FLATWASHER FLATWASHER HEX NUT BOLT NUT,TOPLOCK 5/8 NC PLC BOLT 2017 Alamo Group Inc. Parts Section -229

234 VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 3) 2017 Alamo Group Inc. Parts Section -230

235 VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 3) Continued LOCKNUT BOLT BOLT HEAD RETAINER WLD`MT PIN - VERSA FLAIL MOUNT BOLT BAR FLAP RETAINER, 74" REAR LOCKNUT TLM 1/2 NC PLC CARRIAGE BOLT WASHER TYRONE LOCKWASHER FLATWASHER FLAIL CUTTERHSG ASY, 74CC(74ES ) LOCKWASHER LOCKNUT NO. 2 RED LUBRICAPS BOLT BOLT LOCKWASHER LOCKWASHER BOLT BOLT BOLT BOLT DECAL, OPERATING INSTRUCTIONS DECAL, GREASE FITTING INSIDE DECAL, DANGER-MULTI HAZARD DECAL, FRONT SHIELD REMOVAL DECAL, WARNING SHIELDS & GUARDS DECAL, WARNING OIL LEAK DECAL, ALAMO GROUP DECAL, WARNING BELT SHIELD DECAL, REPLACEMENT PARTS DECAL, DANGER BOOM FLAILS DECAL, THROWN OBJECTS DECAL, RED REFLECTOR DECAL, YELLOW REFLECTOR DECAL, ALAMO IND. GREEN & BLACK DECAL, ALAMO IND. GREEN & BLACK DECAL, HEIGHT ADJUSTMENT PLASTIC TIE-ON 15 LG 2017 Alamo Group Inc. Parts Section -231

236 VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 4) 2017 Alamo Group Inc. Parts Section -232

237 VERSA FLAIL ASY - 74 IN PN & PN SN & UP (PART 4) Continued /16X 7 PLASTIC TIE WRAP SUPPLEMENT INST.INSTRUCTIONS DWG INST BLADE PIN AB Alamo Group Inc. Parts Section -233

238 VERSA FLAIL ASY - 88 IN PN & PN (PART 1) 2017 Alamo Group Inc. Parts Section -234

239 VERSA FLAIL ASY - 88 IN PN & PN (PART 1) Continued VERSA FLAIL, 88" W/CC KNIVES VERSA FLAIL, 88" W/ES KNIVES QD HUB BOLT MOTOR PULLEY MOTOR PLATE BOLT LOCKNUT MOTOR ASY. W/ FITTINGS HYD MOTOR-CAST IRON,FLAIL HD ADAPTER, HYD, ELBOW SPLIT FLANGE KIT # HOSE #20-20FJX -20FJX - 84LG HOSE #20-20FJX -20FJX - 88LG CORDURA SLEEVING -69 INCHES DEFLECTOR, TRASH, 88" (REAR) FLATWASHER LOCKNUT BOLT CTRHSG WLD`MT,88" VERSA-FLAIL RUBBER BUMPER FLAT HEAD BOLT LOCKNUT SPRING,EXTENSION BOLT HEX NUT IDLER PIVOT PIN FLATWASHER COTTER PIN RH IDLER ARM ASY, (FWD ROT) RH IDLER ARM WLD`MT, (FWD ROT) IDLER PULLEY IDLER BEARING SPACER CUTTERSHAFT PULLEY CUTTERSHAFT WASHER BOLT BELT COVER WLD`MT BOLT LOCKNUT FLATWASHER V-BELTS MATCHED PAIR (2 BELTS) 2017 Alamo Group Inc. Parts Section -235

240 VERSA FLAIL ASY - 88 IN PN & PN (PART 2) 2017 Alamo Group Inc. Parts Section -236

241 VERSA FLAIL ASY - 88 IN PN & PN (PART 2) Continued SHOE WEAR PLATE, W/ BOLTS PKG SHOE/WEAR PLATE LOCKNUT TLM 1/2 NC PLC CARRIAGE BOLT 2A PLOW BOLT KEY CUTTERSHAFT BEARING ASY, DRIVE SIDE HHCS 3/8 NF 1-1/8 PL LOCKWASHER,3/8 EXTERNAL TOOTH CUTTERSHAFT BEARING ASY, NON-DRIVE BOLT 3/8 NC GR8 X 1-1/ LOCKNUT TLM 3/8-NC PLC BEARING CUTTERSHAFT CC KNIFE PKG 88" C/S EXTREME SERVICE, KNIFE, PKG FENDER CUTTERSHAFT WLD`MT,88" CUTTERSHAFT, W/CC KNIVES CUTTER SHAFT, W/ES KNIVES ROLLER MOUNTING WLD`MT ROLLER BRG ASY. W/HEX BORE LOCKNUT CARRIAGE BOLT ROLLER BRG SEAL LH ROLLER BRKT ASY. W/HEX BRG RH ROLLER BRKT ASY. W/HEX BRG GREASE FITTING CARRIAGE BOLT LOCKNUT TLM 1/2 NC PLC ROLLER WLD`MT, 88" W/HEX SHAFT SQUARE KEY FOOT GUARD WLD`MT,88" BOLT LOCKWASHER FLATWASHER FLATWASHER HEX NUT BOLT NUT,TOPLOCK 5/8 NC PLC BOLT LOCKNUT 2017 Alamo Group Inc. Parts Section -237

242 VERSA FLAIL ASY - 88 IN PN & PN (PART 3) 2017 Alamo Group Inc. Parts Section -238

243 VERSA FLAIL ASY - 88 IN PN & PN (PART 3) Continued BOLT BOLT HEAD RETAINER WLD`MT PIN - VERSA FLAIL MOUNT BOLT BAR FLAP RETAINER, 88" REAR LOCKNUT CARRIAGE BOLT WASHER TYRONE LOCKWASHER FLATWASHER FLAIL CUTTERHSG ASY, 88CC(88ES ) LOCKWASHER LOCKNUT NO. 2 RED LUBRICAPS BOLT BOLT LOCKWASHER LOCKWASHER BOLT BOLT BOLT BOLT DECAL, OPERATING INSTRUCTIONS DECAL, GREASE FITTING INSIDE DECAL, DANGER-MULTI HAZARD DECAL, FRONT SHIELD REMOVAL DECAL, WARNING SHIELDS & GUARDS DECAL, WARNING OIL LEAK DECAL, ALAMO GROUP DECAL, WARNING BELT SHIELD DECAL, REPLACEMENT PARTS DECAL, DANGER BOOM FLAILS DECAL, THROWN OBJECTS DECAL, RED REFLECTOR DECAL, YELLOW REFLECTOR DECAL, ALAMO IND. GREEN & BLACK DECAL, ALAMO IND. GREEN & BLACK DECAL, HEIGHT ADJUSTMENT PLASTIC TIE-ON 15 LG /16X 7 PLASTIC TIE WRAP 2017 Alamo Group Inc. Parts Section -239

244 VERSA FLAIL ASY - 88 IN PN & PN (PART 4) 2017 Alamo Group Inc. Parts Section -240

245 VERSA FLAIL ASY - 88 IN PN & PN (PART 4) Continued SUPPLEMENT INST.INSTRUCTIONS DWG INST BLADE PIN AB INSERT SHEET PARTS 88VERSA FL 2017 Alamo Group Inc. Parts Section -241

246 VERSA MOWER - FLAIL VALVE BOLT BOLT LOCKNUT FLATWASHER TUBE SPACER WELDMENT, COVER VAVLE HANDLE KIT VALVE ASSEMBLY WELDMENT, VALVE MOUNT DECAL, VALVE OPERATION 2017 Alamo Group Inc. Parts Section -242

247 THIS PAGE INTENTIONALLY LEFT BLANK 2017 Alamo Group Inc. Parts Section -243

248 VERSA MOWER HEAD ASY - 5 FT BAR ( ) VM60 HEAD, ASY, 5 BAR CGS V/M-60 SUB-ASSY BAR ASY CG 5 DUAL REAR V/M ASY CG DUAL 5 FRONT V/M FLATWASHER STD 3/8 - PLATED LOCKNUT TLM 3/8-NC PLC HEXB 3/8-16 X 1 PL BUMPER, VERSA, BOTTOM WLDMT- CHAINGUARD- CORNER HHCS 3/8-16UNC 1-1/2 PL FCEB ELEV 3/8 NC 2-1/2 PL PIN-EXTENSION ARM FITTING,GREASE 1/8 MP STRAIGHT NUT HEX 3/8 NC PL 2017 Alamo Group Inc. Parts Section -244

249 VERSA MOWER HEAD ASY - 5 FT BAR ( ) Continued NUT,TOPLOCK 5/8 NC PLC HHCS 1/2 NC 3 PL LOCKNUT TLM 1/2 NC PLC WLDMT, HEAD RETAINER ADP HYD ELBOW 20MJ -20FJX ADP TUBE ELBOW 20MJ-20FJX 90? 2017 Alamo Group Inc. Parts Section -245

250 VERSA MOWER HEAD SUB ASSY - 5 FT BAR ( ) V/M-60 SUB-ASSY BAR WLDMT, MOWER BLADE CARRIER, ASY, BAR STRT SKID SHOE SPACER,1-1/4 BLADE BAR 2017 Alamo Group Inc. Parts Section -246

251 VERSA MOWER HEAD SUB ASSY - 5 FT BAR ( ) Continued ASY,MOTOR & SPINDLE VM LOCKNUT TLM 3/8-NC PLC FLATWASHER STD 3/8 - PLATED NUT,HEX TOPLOCK 3/4 NC GR.C PL FSCS 3/8 NC 1-1/ SHCS 3/4 NC 3-3/4 PL HHCS 3/4 NC 2-1/2 PL LOCKWASHER, 3/4, HVY, PL 2017 Alamo Group Inc. Parts Section -247

252 VERSA MOWER HEAD ASSY - 5 FT PAN ( ) HEAD, ASY, 5 PAN CGS V/M-60 SUB ASSY PAN ASY CG 5 DUAL REAR V/M ASY CG DUAL 5 FRONT V/M FLATWASHER STD 3/8 - PLATED LOCKNUT TLM 3/8-NC PLC HEXB 3/8-16 X 1 PL BUMPER, VERSA, BOTTOM WLDMT- CHAINGUARD- CORNER WLDMT, HEAD RETAINER HHCS 3/8-16UNC 1-1/2 PL FCEB ELEV 3/8 NC 2-1/2 PL PIN-EXTENSION ARM LOCKNUT TLM 1/2 NC PLC FITTING,GREASE 1/8 MP STRAIGHT NUT HEX 3/8 NC PL NUT,TOPLOCK 5/8 NC PLC 2017 Alamo Group Inc. Parts Section -248

253 VERSA MOWER HEAD ASSY - 5 FT PAN ( ) Continued HHCS 1/2 NC 3 PL ADP HYD ELBOW 20MJ -20FJX ADP TUBE ELBOW 20MJ-20FJX 90? 2017 Alamo Group Inc. Parts Section -249

254 VERSA MOWER HEAD SUB ASSY - 5 FT PAN ( ) 2017 Alamo Group Inc. Parts Section -250

255 VERSA MOWER HEAD SUB ASSY - 5 FT PAN ( ) Continued V/M-60 SUB ASSY PAN WLDMT, MOWER PAN ASSEMBLY 60 V/M STUMP SKID SHOE ASY,MOTOR & SPINDLE VM LOCKWASHER, 3/4, HVY, PL LOCKNUT TLM 3/8-NC PLC FLATWASHER STD 3/8 - PLATED NUT,HEX TOPLOCK 3/4 NC GR.C PL FSCS 3/8 NC 1-1/ SHCS 3/4 NC 2-1/2 PL HHCS 3/4 NC 2-1/2 PL Alamo Group Inc. Parts Section -251

256 VERSA MOWER HEAD ASSY - 5 FT PAN WITH BREAKAWAY ( ) LOCKNUT TLM 1/2 NC PLC FLATWASHER STD 3/8 - PLATED HEXB 3/8-16 X 1 PL LOCKNUT TLM 3/8-NC PLC HHCS 3/8-16UNC 1-1/2 PL NUT,TOPLOCK 5/8 NC PLC HHCS 1/2 NC 3 PL PIN-EXTENSION ARM FCEB ELEV 3/8 NC 2-1/2 PL RUBBER FLAP-REAR ASY CG DUAL 5 FRONT V/M MOWER, SUB ASY, VERSA WLDMT- CHAINGUARD- CORNER ASY CG 5 REAR V/M BREAKAWAY BUMPER, VERSA, BOTTOM ADP HYD ELBOW 20MJ -20FJX ADP TUBE ELBOW 20MJ-20FJX 90? 2017 Alamo Group Inc. Parts Section -252

257 VERSA MOWER HEAD ASSY - 5 FT PAN WITH BREAKAWAY ( ) Continued WLDMT, HEAD RETAINER NUT HEX 3/8 NC PL 2017 Alamo Group Inc. Parts Section -253

258 VERSA MOWER HEAD SUB ASSY - 5 FT PAN WITH BREAKAWAY ( ) FITTING,GREASE 1/8 MP STRAIGHT LOCKWASHER, 3/4, HVY, PL FLATWASHER STD 3/8 - PLATED LOCKNUT TLM 3/8-NC PLC 2017 Alamo Group Inc. Parts Section -254

259 VERSA MOWER HEAD SUB ASSY - 5 FT PAN WITH BREAKAWAY ( ) Continued HHCS 3/8-16UNC 1-1/2 PL NUT,HEX TOPLOCK 3/4 NC GR.C PL FSCS 3/8 NC 1-1/ SKID SHOE SHCS 3/4 NC 2-1/2 PL WLDMT, MOWER - BREAKAWAY SKID SHOE FLAP SUPPORT WLDMT HHCS 3/4 NC 2-1/2 PL PAN ASSEMBLY 60 V/M STUMP ASY,MOTOR & SPINDLE VM CLAMP BAR 2017 Alamo Group Inc. Parts Section -255

260 VERSA MOWER HEAD ASSY - 6 FT BAR ( ) HEAD, V/M ASY W/BAR V/M 72 SUB-ASSY BAR ASY CG DUAL 6 FRONT V/M BUMPER, VERSA, BOTTOM FCEB ELEV 3/8 NC 2-1/2 PL NUT HEX 3/8 NC PL WLDMT- CHAINGUARD- CORNER ASY CG DUAL 6 REAR V/M FLATWASHER STD 3/8 - PLATED HEXB 3/8-16 X 1 PL LOCKNUT TLM 3/8-NC PLC HHCS 3/8-16UNC 1-1/2 PL WLDMT, HEAD RETAINER NUT,TOPLOCK 5/8 NC PLC 2017 Alamo Group Inc. Parts Section -256

261 VERSA MOWER HEAD SUB ASSY - 6 FT BAR ( ) V/M 72 SUB-ASSY BAR WLDMT, MOWER MTR & SPINDLE ASY VM FITTING,GREASE 1/8 MP STRAIGHT FLATWASHER STD 3/8 - PLATED LOCKNUT TLM 3/8-NC PLC NUT,HEX TOPLOCK 3/4 NC GR.C PL FSCS 3/8 NC 1-1/ Alamo Group Inc. Parts Section -257

262 VERSA MOWER HEAD SUB ASSY - 6 FT BAR ( ) Continued SHCS 3/4 NC 3-3/4 PL BLADE CARRIER, ASY, BAR SPACER,1-1/4 BLADE BAR HHCS 3/4 NC 2-1/2 PL LOCKWASHER, 3/4, HVY, PL SKID SHOE 6 FT VERSA HEAD 2017 Alamo Group Inc. Parts Section -258

263 VERSA MOWER HEAD ASY 6 FT PAN ( ) HEAD, V/M ASY W/PAN V/M 72 SUB-ASSY PAN ASY CG DUAL 6 FRONT V/M BUMPER, VERSA, BOTTOM FCEB ELEV 3/8 NC 2-1/2 PL NUT HEX 3/8 NC PL WLDMT- CHAINGUARD- CORNER ASY CG DUAL 6 REAR V/M FLATWASHER STD 3/8 - PLATED HEXB 3/8-16 X 1 PL LOCKNUT TLM 3/8-NC PLC HHCS 3/8-16UNC 1-1/2 PL WLDMT, HEAD RETAINER NUT,TOPLOCK 5/8 NC PLC 2017 Alamo Group Inc. Parts Section -259

264 VERSA MOWER HEAD SUB ASSY - 6 FT PAN ( ) V/M 72 SUB-ASSY PAN WLDMT, MOWER MTR & SPINDLE ASY VM FITTING,GREASE 1/8 MP STRAIGHT FLATWASHER STD 3/8 - PLATED LOCKNUT TLM 3/8-NC PLC 2017 Alamo Group Inc. Parts Section -260

265 VERSA MOWER HEAD SUB ASSY - 6 FT PAN ( ) Continued NUT,HEX TOPLOCK 3/4 NC GR.C PL FSCS 3/8 NC 1-1/ SHCS 3/4 NC 2-1/2 PL STUMP JUMPER PAN ASSY HHCS 3/4 NC 2-1/2 PL LOCKWASHER, 3/4, HVY, PL SKID SHOE 6 FT VERSA HEAD 2017 Alamo Group Inc. Parts Section -261

266 VERSA MOWER HEAD - CHAIN GUARD - PN MOWER, SUB ASY, VERSA ASY CG DUAL 5 FRONT V/M ASY CG 5 REAR V/M BREAKAWAY CLAMP BAR RUBBER FLAP-REAR HHCS 3/8-16UNC 1-1/2 PL LOCKNUT TLM 3/8-NC PLC FLATWASHER STD 3/8 - PLATED HEXB 3/8-16 X 1 PL Alamo Group Inc. Parts Section -262

267 VERSA MOWER HEAD - MOTOR & SPINDLE ASSEMBLY PN C 1 ASSY,SPLINED SPINDLE MOTOR HYD GEAR 9CIR SPLINED SPLIT FLANGE KIT 1-1/ ADP HYD ELBOW 24FL-20MJ DOUBLE END STUD 1/2-13UNC HHCS 1/2 NC 2-1/4 PL LOCKNUT TLM 1/2 NC PLC 2017 Alamo Group Inc. Parts Section -263

268 VERSA MOWER HEAD - MOTOR & SPINDLE ASSEMBLY PN Continued GREASE RELIEF FITTING 1-5LBS 2017 Alamo Group Inc. Parts Section -264

269 VERSA MOWER HYDRAULIC SYSTEM (PART 1) 2017 Alamo Group Inc. Parts Section -265

270 VERSA MOWER HYDRAULIC SYSTEM (PART 1) Continued FLANGE KIT IN - TANK FILTER FILTER ELEMENT ADAPTER ELBOW ADAPTER HOSE BIB ELBOW ADAPTER ADAPTER ORIFICE PLATE VINYL TAPE RED 1/2" WIDE STRAIGHT ADAPTER ELBOW ELBOW - 45 DEG ADAPTER HOSE-TANK TO PUMP * HOSE-PUMP TO CUTTER VALVE * HOSE-PUMP TO CONTROL VALVE HOSE-FILTER TUBE TO TEE HOSE-CUTTER VALVE TO MOTOR, 60" VERSA ROTARY HOSE-CUTTER VALVE TO MOTOR, 72" VERSA ROTARY HOSE-MOTOR TO CUTTER VALVE, 60" VERSA ROTARY HOSE-MOTOR TO CUTTER VALVE, 72" VERSA ROTARY HOSE-CUTTER VALVE TO TEE HOSE-CONTROL VALVE TO CUTTER VALVE ( ROPS UNITS ) HOSE-CONTROL VALVE TO CUTTER VALVE ( CAB UNITS ) HOSE-CONTROL VALVE TO TILT CYLINDER ( CAB UNITS ) HOSE-CONTROL VALVE TO TILT CYLINDER ( ROPS UMITS ) HOSE-CONTROL VALVE TO LIFT CYLINDER ( ROPS UNITS ) HOSE-CONTROL VALVE TO LIFT CYLINDER ( CAB UNITS ) HOSE CLAMP FILTER RETURN TUBE ADAPTER ELBOW SPLIT FLANGE KIT FLANGE KIT REDUCER ELBOW ELBOW ADAPTER 2017 Alamo Group Inc. Parts Section -266

271 VERSA MOWER HYDRAULIC SYSTEM (PART 2) 2017 Alamo Group Inc. Parts Section -267

272 VERSA MOWER HYDRAULIC SYSTEM (PART 2) Continued HOSE ( WITH # 4MJ ) HOSE ( ROPS UNITS ) HOSE ( CAB UNITS ) HOSE ( ROPS UNITS ) HOSE ( CAB UNITS ) STRAIGHT ADAPTER ELBOW TEE STRAIGHT ADAPTER VINYL TAPE BLUE 1/2" WIDE VINYL TAPE BLUE 1/4" WIDE VINYL TAPE GREEN 1/2" WIDE VINYL TAPE GREEN 1/4" WIDE VINYL TAPE ORANGE 1/2" WIDE 2017 Alamo Group Inc. Parts Section -268

273

274 TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manuals thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT ( Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER 1. Provide a Roll-Over-Protective Structure that meets the requirements of this standard. 2. Provide seat belts that meet the requirements of this paragraph of this standard and SAE J4C. 3. Ensure that each employee uses such seat belt while the tractor is moving. 4. Ensure that each employee tightens the seat belt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seat belt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going, especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly, no jerky turns, starts, or stops. 8. Hitch only to the draw bar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.

275 ALAMO INDUSTRIAL Limited Warranty 1. Limited Warranties Alamo industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( purchaser ) and warrants for six months to the original commercial or industrial purchaser ( purchaser ) that the goods purchased are free from defects in material or workmanship Manufacturer will replace for the purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your operator s manual Except as provided herein, no employee, agent, dealer, or other person is authorized to give any warranties of any nature on behalf of manufacturer. 2. Remedies And Procedures This limited warranty is not effective unless the purchaser returns the registration and warranty form to manufacturer within 30 days of purchase Purchaser claims must be made in writing to the authorized dealer ( dealer ) from whom purchaser purchased the goods or an approved authorized dealer ( dealer ) within 30 days after purchaser learns of the facts on which the claim is based Purchaser is responsible for returning the goods in question to the dealer If after examining the goods and/or parts in question, manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, manufacturer will: (A) repair or replace the defective goods or part(s) or (B) reimburse purchaser for the cost of the part(s) and reasonable labor charges (as determined by manufacturer) if purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by manufacturer. The choice of remedy shall belong to manufacturer Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by manufacturer and for returning the goods to the dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the dealer to the designated factory. 3. Limitation Of Liability Manufacturer disclaims any express (except as set forth herein) and implied warranties with respect to the goods including, but not limited to, merchantability and fitness for a particular purpose Manufacturer makes no warranty as to the design, capability, capacity, or suitability for use of the goods Except as provided herein, manufacturer shall have no liability or responsibility to purchaser or any other person or entity with respect to any liability, loss, or damage caused or alleged to be caused directly or indirectly by the goods including, but not limited to, any indirect, special, consequential, or incidental damages resulting from the use or operation of the goods or any breach of this warranty. Not withstanding the above limitations and warranties, manufacturer s liability hereunder for damages incurred by purchaser or others shall not exceed the price of the goods No action arising out of any claimed breach of this warranty or transactions under this warranty may be brought more than two (2) years after the cause of action has occurred. 4. Miscellaneous Proper venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe county, Texas Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein Applicable law may provide rights and benefits to purchaser in addition to those provided herein. Keep for your records Attention: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Alamo Industrial Implement Model Serial Number Date Purchased Dealer Attention: Read your operator s manual ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas

276

277 1502 E. Walnut St. Seguin, Texas Sales and Marketing Tel Fax Warranty Registration/Claims Return Authorizations Online Part Orders Techical Information Tel Fax VERSA Boom Parts Manual (PUB 12-08) P/N P