2815R2,2810R R2, 12810R2

Transcription

1 2815R2,2810R R2, 12810R2 FLEX WING ROTARY CUTTER Published 07/1 PARTS MANUAL SECTION 95A An Operator s Manual was shipped with the equipment. The Operator s Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator s Manual is not with the equipment, contact your dealer or Bush Hog to obtain a copy before operating the equipment. Important Operating and Safety Instructions are found in the Mower Safety Video that can be instantly accessed on the internet at:

2 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. For maximum safety and to guarantee optimum product reliability, always use genuine BUSH HOG Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.direct any questions regarding parts to: BUSH HOG 2501 Griffin Ave. Selma, AL Contact Us Alamo Group Inc.

3 To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty RegistrationForm in full and return it to within 0 Days. Make certain the Serial Number of the Machine is recorded on thewarranty Card and on the Warranty Form that you retain.

4 LIMITED WARRANTY Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state and municipalities use and ninety (90) days for commercial use from date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective parts. Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hog dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship. DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES Bush Hog s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale or use of the items warranted. Such incidental and consequential damages shall include but not be limited to: transportation charges other than normal freight charges; cost of installation other than cost approved by Bush Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond the control of Bush Hog. THIS LIMITED WARRANTY SHALL NOT APPLY: 1. To vendor items which carry their own warranties, such as engines, tires, and tubes. 2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability.. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in the sole judgement of Bush Hog, affects its performance, stability or reliability. 5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure. 6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the company s sole judgement is a wear item. NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN WRITING AND SIGNED BY BUSH HOG S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA 670. Record the model number, serial number and date purchased. This information will be helpful to your dealer if parts or service are required. MODEL NUMBER SERIAL NUMBER DATE OF RETAIL SALE MAKE CERTAIN THE WARRANTY HAS BEEN FILED WITH BUSH HOG SELMA, ALABAMA

5 BUSH HOG/ LAND MAINTENANCE REPAIR PARTS MANUAL July, R2, 2810R2, 12815R2, 12810R2 ROTARY CUTTER CONTENTS ALPHABETICAL INDEX PAGE Axle, Center & Wing Units...95A-5- Axle, Single & Dual...95A-5- Axle, Tandem...95A-5-5 Baffle Kit...95A-6-1 Base Assembly, Center...95A-1-1 Base Assembly, R.H. Wing & L.H. Wing...95A-1-2 Blades & Blade Holders...See Base Assemblies Chain, Safety Tow...95A-5-1 Chains, Highway Use...95A-2-1 through 95A-2-2 Cylinders, Hydraulic...95A-7-2 Decal Kits...95A-8-1, See Base Assemblies Driveline Holder Assembly...95A-5-2 Driveshafts, Comer / EG...95A--1 through 95A--6 Gearbox, Transfer 50 RPM (Mfg. by Bondioli & Pavesi)...95A--1 Gearbox, Transfer 1000 RPM (Mfg. by Bondioli & Pavesi)...95A--2 Gearbox, Transfer 1000 RPM (Mfg. by Comer)...95A-- Gearbox, Center and L.H. Wing 50 RPM...95A-- Gearbox, R.H. Wing 50 RPM...95A--5 Gearbox, Center 1000 RPM...95A--6 Gearbox, L.H. Wing 1000 RPM...95A--7 Gearbox, R.H. Wing 1000 RPM...95A--8 Hitch Assemblies, Swivel Pivot...95A-5-2 Hydraulic Fittings To Tractor Remotes...95A-7-1 Jackstand...95A-5-1 Leveling Rod Assembly...95A-5-1 Shield, Wing Driveshafts...95A-2- Shield Assembly, Center...95A-2- SMV Sign & Hose Holder...95A-1- Tire, Airplane...95A-5-7 Tire, Solid & Foam Filled...95A-5-6 Tongue Assembly...95A-5-1 Weight Box Assembly, 2810R2 & 12810R2...95A-1-

6

7 CENTER DECK ASSEMBLY 2815R2 & 2810R2 (50 RPM Models) 12815R2 & 12810R2 (1000 RPM Models) Center Deck w/decals Center Deck w/rings & Decals Skid R.H Skid L.H Carriage Bolt, 1/2 x 1-1/2 Gr Lockwasher, 1/ Hex Nut, 1/ Transfer Gearbox (50 - B&P) Transfer Gearbox ( B&P) Transfer Gearbox ( Comer) Capscrew, 5/8 x 2-1/ Gr Locknut, 5/8 Flanged Gearbox (50 RPM) Gearbox (1000 RPM) Capscrew / x 2-1/2 Gr Cotter Pin M10 x BH Lock Collar Roll Pin, /8 x 1-1/ Hinge Rod Pan Weldment Blade, Parallel Uplift Blade Bolt Kit BH Blade Bolt Lockwasher, 1-1/ BH Jamb Nut, 1-1/ Wing Latch Pin BH Presto Pin Locknut, / Shaft Cover (2810, 12810) Capscrew, M8 x 1.25 x BH Lockwasher, M Decal, Important 1 0 D57 Decal, Danger 1 1 D81 Decal, Danger 1 2 D551 Decal, Blade Rotation CCW Spring Washer 1 D555 Decal, Danger 2 5 D565 Decal, Danger 2 6 D56 Decal, Danger 1 7 D55 Decal, Warning 1 8 D61 Decal, Danger - Thrown Obj. 2 9 D559 Decal, Bush Hog Parts 1 0 D587 Decal, Lubrication 1 1 D58 Decal, Warning (1000 RPM Only) 1 2 D575 Decal, Danger (Crushing Hazard) 1 D59 Decal, Sheet Caster Nut, 2-12 (Blade Pan) 1 95A-1-1

8 WING DECK ASSEMBLY 2815R2 & 2810R2 (50 RPM Models) 12815R2 & 12810R2 (1000 RPM Models) This Parts Listing applies to RH and LH Wings. RH WING SHOWN R.H. Wing Frame w/decals R.H. Wing Frame w/rings & Decals L.H. Wing Frame w/decals L.H. Wing Frame w/rings & Decals Front Skid R.H Front Skid L.H Rear Skid R.H Rear Skid L.H Plow Bolt, /8 x 1-1/ BH Flatwasher, / Lockwasher, / Hex Nut, / Decal, Bush Hog 1 9 D551 Decal, Blade Rot. CCW R.H. Wing 1 D552 Decal, Blade Rot. CW L.H. Wing 1 10 D61 Decal, Thrown Object 2 11 D56 Decal, Danger Gearbox R.H. 50 RPM Gearbox L.H. 50 RPM Gearbox R.H RPM Gearbox L.H RPM Locknut, 5/8 Flanged Capscrew, 5/8 x 2-1/ Gr Push Over Assy Cylinder Pin Flatwasher, Cotter Pin, /16 x 1-1/ Pin Wing Lift Cylinder Capscrew, /8 x Pan Weldment Blade, Uplift CCW R.H. Wing Blade, Uplift CW L.H. Wing Blade Bolt Kit BH Blade Bolt Lockwasher, 1-1/ BH Jamb Nut, 1-1/ Cotter Pin M10 x Castle Nut, 2 x12 (Blade Pan) Reflector, Amber Reflector, Red Roll Pin, 1/ x 1-/ Washer, Spring 1 95A-1-2

9 WEIGHT BOX ASSEMBLY 2810R2 & 12810R2 Models , 2, , 16, 17, , 16, 17, 18 1, 16, 17, , 16, 17, , 16, 17, Weight Box Assy Skid, Front L.H Skid, Front R.H Skid Hinge Rod BH Lock Collar Roll Pin, /8 x 1-1/ Chain Assy, Front (Single) Chain Assy, Front (Double) Chain Assy, Rear (Single) Chain Assy, Rear (Double) Chain Support (Front) Rod, Chain Chain, 5 Link (Single Row) Chain, 9 Link (Double Row) Chain Support (Rear) Rod, Chain Carriage Bolt, /8 x 1-1/ Flatwasher, / Lockwasher, / Hex Nut, / Eyebolt Hex Nut, Capscrew, / x 2-1/ Locknut, / Lockwasher, / Flatwasher, / Bushing Reflector, Amber Reflector, Red Decal, Bush Hog Capscrew, 1 x -/ Lockwasher, # Hd Plow Bolt, /8 x 1-1/ Gr A-1-

10 SMV SIGN & HOSE HOLDER FOR 2815R2, 2810R2, 12815R2 & 12810R2 MODELS 2 11, 12, SMV Mount Weldment SMV Spade Bracket SMV Sign Rod, Hose Holder Capscrew, 5/8 x 2 Gr Flatwasher, 5/ Lockwasher, 5/ Hex Nut, 5/ Capscrew, 5/16 x 1 Gr BH Locknut, 5/ Capscrew, 1/ x 7/8 Gr Lockwasher, 1/ BH Hex Nut, 1/ 2 95A-1-

11 FRONT AND REAR SINGLE ROW HIGHWAY CHAINS 2815R2 & 2810R2 (50 RPM Models) 12815R2 & 12810R2 (1000 RPM Models) Carriage Bolt, /8 x 1-1/2 Gr BH Capscrew, /8 x 1-1/ Gr Hex Nut, / Carriage Bolt, /8 x 1-1/ Carriage Bolt, 1/2 x 1-1/ Flanged Lock Nut, 1/ Front Center Chain Assy Chain, Plated Front Outside Chain Assy Chain, Plated Front Wing Chain Assy Chain, Plated Rear Center Chain Assy Chain, Plated Chain, Plated - Link Rear Wing Chain Assy Chain, Plated Chain Assy, L.H. Wing Chain, Plated - Link Chain Assy, R.H. Wing Chain, Plated - Link Chain Assy Wing Axle, Inside Chain, Plated - Link Chain Assy Wing Axle Chain, Plated - Link Chain, Plated - 9 Link 95A-2-1

12 FRONT AND REAR DOUBLE ROW HIGHWAY CHAINS 2815R2 & 2810R2 (50 RPM Models) 12815R2 & 12810R2 (1000 RPM Models) Carriage Bolt, /8 x 1-1/2 Gr BH Capscrew, /8 x 1-1/ Gr Hex Nut, / Carriage Bolt, /8 x 1-1/ Carriage Bolt, 1/2 x 1-1/ Flanged Lock Nut, 1/ Front Center Chain Assy Chain, Plated (9 Link) Front Outside Chain Assy Chain, Plated (9 Link) Front Wing Chain Assy Chain, Plated (9 Link) Rear Center Chain Assy Chain, Plated (9 Link) Chain, Plated (7 Link) Rear Wing Chain Assy Chain, Plated - 11 link Chain Assy, L.H. Wing Chain, Plated - 7 Link Chain Assy, R.H. Wing Chain, Plated - 7 Link Chain Assy Wing Axle, Inside Chain, Plated - 9 Link Chain Assy Wing Axle Chain, Plated - 7 Link Chain, Plated - 9 Link 95A-2-2

13 CENTER SHIELD ASSEMBLY , 28, , Pivot Bracket Shield, Input Shield w/decals Lynch Pin Rear Shield Support Input Shield Bottom w/decal 1 7 D56 Decal, Danger Center Shield Bottom w/decal Decal, Important Decal, Important Decal, Model Decal, Model Decal, Model Decal, Model Owner s Manual Tube Assy Manual Cap Seal , Manual Holder Cap BH Capscrew, M10 x 1.50 x 25mm Lockwasher, M BH Capscrew, /8 x / Gr Locknut, / BH Flatwasher, / BH Carriage Bolt, /8 x Capscrew, M BH Lockwasher, M Capscrew, 1/2 x 1-1/ Flatwasher, 1/ Locknut, 1/ Capscrew, 1/ x 7/ BH Flatwasher, 1/ Lockwasher, 1/ BH Hex Nut, 1/ 95A-2-

14 WING DRIVELINE SHIELDING ,, Driveling Shield Cone BH Capscrew, M10 x 1.5 x Lockwasher, M C Flatwasher, M10 95A-2-

15 TRANSFER GEARBOX ASSEMBLY RPM MFG. BY BONDIOLI & PAVESI MODEL 2815R2 & 2810R2 (50 RPM) Top Cover Drain Plug (Magnetic) Output Shafts 1-/ 20 Spline Oil Seal Snap Ring 85 x mm Shim Kit Bearing 5 x 72 x 18.25mm Housing Input Shaft Breather Plug (Gas) / Capscrew M10 x 22 x 1.5 C Gear Set for 50 RPM Gearbox (Two 19 Tooth Gears and One 2 Tooth Gear) Lockwasher, M Bearing 95A--1

16 NOTE: BEFORE ORDERING PARTS FOR THIS GEARBOX FIRST DETERMINE IF THE GEARBOX IS A COMER OR A BONDIOLI & PAVESI MANUFACTURED GEARBOX ASSEMBLY. DETERMINE THIS FROM THE ID TAG ON TOP OF THE GEARBOX HOUSING TRANSFER GEARBOX ASSEMBLY RPM MFG. BY BONDIOLI & PAVESI MODEL 12815R2 & 12810R2 (1000 RPM) Top Cover Drain Plug (Magnetic) Output Shafts 1-/ 20 Spline Oil Seal Snap Ring 85 x mm Shim Kit Bearing 5 x 72 x 18.25mm Housing Input Shaft Breather Plug (Gas) / Capscrew M10 x 22 x 1.5 C Gear Set for 1000 RPM Gearbox (Two 27 Tooth Gears and One 20 Tooth Gear) Lockwasher, M Bearing 95A--2

17 BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL April, 2012 NOTE: BEFORE ORDERING PARTS FOR THIS GEARBOX FIRST DETERMINE IF THE GEARBOX IS A COMER OR A BONDIOLI & PAVESI MANUFACTURED GEARBOX ASSEMBLY. DETERMINE THIS FROM THE ID TAG ON TOP OF THE GEARBOX HOUSING TRANSFER GEARBOX ASSEMBLY RPM mfg. by comer MODEL 12715R2 & 12710R2 (1000 RPM) , REF. NO. PART NO. DESCRIPTION QTY Bearing Casing Oil Seal Snap Ring Shim Gear, 20 Teeth (1000 RPM) Shaft 1-/ Z Gear, 27 Teeth (1000 RPM) Shaft, 1-/ Z Cover Capscrew M10 x 1.5 x 5 Gr Gas Plug / Shim Shim Shim Vent Plug 1 95A--

18 BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL May, GEARBOX ASSEMBLY 50 RPM, Ratio 1:1.60 Center R2 & 2810R2 L.H. Wing R Housing,Gearbox - HD Shaft, Output HD225B Bearing,Roller-90 X 50 X Shaft,Input - HD Cap,Input Shaft - HD Cover,Top - HD Cap,Solid End - HD Bearing,Roller X 75 X Seal,Dbl Lip Oil x125x Ring,Internal Snap X Spacer,Small - HD Spacer,Large - HD Lockwasher /8 Cp BH Hex Soc Hd Cpsc /8 X 1 G Nut,Hex Flg.Slotted - M0-P A Seal,Dbl Lip Oil-.5x69x Nut, Slotted Hex Jam 2" Washer,Sealing - M Gasket,Input Cap -.10mm Gasket,Input Cap -.25mm Plug,Vent - M16 X Sight Glass Plug Pin, Cotter.6mm X 65mm Plug Pipe Socket Head / Protector, Seal Washer, Spring 2.00" Pin,Cotter 10mm X 100mm Dipstick,Oil Level-M16 X Kit,Gear - 2T & 15T Kit,Gear Shim - HD225 1

19 GEARBOX ASSEMBLY 50 RPM, Ratio 1:1.60 R.H. Wing R2 & 2810R Housing,Gearbox - HD Shaft, Output HD225B Bearing,Roller-90 X 50 X Shaft,Input - HD Cap,Input Shaft - HD Cover,Top - HD Cap,Solid End - HD Bearing,Roller X 75 X Seal,Dbl Lip Oil x125x Ring,Internal Snap X Spacer,Small - HD Spacer,Large - HD Lockwasher /8 Cp BH Hex Soc Hd Cpsc /8 X 1 G Nut,Hex Flg.Slotted - M0-P A Seal,Dbl Lip Oil-.5x69x Nut, Slotted Hex Jam 2" Washer,Sealing - M Gasket,Input Cap -.10mm Gasket,Input Cap -.25mm Plug,Vent - M16 X Sight Glass Plug Pin, Cotter.6mm X 65mm Plug Pipe Socket Head / Protector, Seal Washer, Spring 2.00" Pin,Cotter 10mm X 100mm Dipstick,Oil Level-M16 X Kit,Gear - 2T & 15T Kit,Gear Shim - HD225 1

20 GEARBOX ASSEMBLY 1000 RPM, Ratio 1.15:1 CENTER R2 & 12810R Housing,Gearbox - HD Shaft, Output HD225B Bearing,Roller-90 X 50 X Shaft,Input - HD Cap,Input Shaft - HD Cover,Top - HD Cap,Solid End - HD Bearing,Roller X 75 X Seal,Dbl Lip Oil x125x Ring,Internal Snap X Spacer,Small - HD Spacer,Large - HD Lockwasher /8 Cp BH Hex Soc Hd Cpsc /8 X 1 G Nut,Hex Flg.Slotted - M0-P A Seal,Dbl Lip Oil-.5x69x Nut, Slotted Hex Jam 2" Washer,Sealing - M Gasket,Input Cap -.10mm Gasket,Input Cap -.25mm Plug,Vent - M16 X Sight Glass Plug Pin, Cotter.6mm X 65mm Plug Pipe Socket Head / Protector, Seal Washer, Spring 2.00" Pin,Cotter 10mm X 100mm Dipstick,Oil Level-M16 X Kit,Gear - 20T & 2T Kit,Gear Shim - HD225 1

21 GEARBOX ASSEMBLY 1000 RPM, Ratio 1:1.75 L.H. Wing R Housing,Gearbox - HD Shaft, Output HD225B Bearing,Roller-90 X 50 X Shaft,Input - HD Cap,Input Shaft - HD Cover,Top - HD Cap,Solid End - HD Bearing,Roller X 75 X Seal,Dbl Lip Oil x125x Ring,Internal Snap X Spacer,Small - HD Spacer,Large - HD Lockwasher /8 Cp BH Hex Soc Hd Cpsc /8 X 1 G Nut,Hex Flg.Slotted - M0-P A Seal,Dbl Lip Oil-.5x69x Nut, Slotted Hex Jam 2" Washer,Sealing - M Gasket,Input Cap -.10mm Gasket,Input Cap -.25mm Plug,Vent - M16 X Sight Glass Plug Pin, Cotter.6mm X 65mm Plug Pipe Socket Head / Protector, Seal Washer, Spring 2.00" Pin,Cotter 10mm X 100mm Dipstick,Oil Level-M16 X Kit,Gear - 22T & 16T Kit,Gear Shim - HD225 1

22 GEARBOX ASSEMBLY 1000 RPM, Ratio 1:1.75 R.H. Wing R2 & 12810R Housing,Gearbox - HD Shaft, Output HD225B Bearing,Roller-90 X 50 X Shaft,Input - HD Cap,Input Shaft - HD Cover,Top - HD Cap,Solid End - HD Bearing,Roller X 75 X Seal,Dbl Lip Oil x125x Ring,Internal Snap X Spacer,Small - HD Spacer,Large - HD Lockwasher /8 Cp BH Hex Soc Hd Cpsc /8 X 1 G Nut,Hex Flg.Slotted - M0-P A Seal,Dbl Lip Oil-.5x69x Nut, Slotted Hex Jam 2" Washer,Sealing - M Gasket,Input Cap -.10mm Gasket,Input Cap -.25mm Plug,Vent - M16 X Sight Glass Plug Pin, Cotter.6mm X 65mm Plug Pipe Socket Head / Protector, Seal Washer, Spring 2.00" Pin,Cotter 10mm X 100mm Dipstick,Oil Level-M16 X Kit,Gear - 22T & 16T Kit,Gear Shim - HD225 1

23 WING DRIVESHAFT For 2815R2, 2810R2, 12815R2 & 12810R2 Models 1-/ - 20 Spline Manufactured by Comer / EG ASAE SIZE Complete Yoke Cross Journal Set Circlip Grease Nipple Outer Yoke Roll Pin For Outer Tube Bing Complete Outer Tube Inner Tube Roll Pin For Inner Tube Inner Yoke Complete Disc Clutch Guard Ret. Collar (Outer Tube) Bolt Guard Ret. Collar (Inner Tube) Safety Chains Complete Guard w/inst. Manual Yoke Tapered Pin Set, 1-/ Spring Flanged Yoke Bushing Lining Ring Clutch Support Inner Plate Pressure Plate BH Capscrew, M10 x 1.5 x Female Tube w/yoke & Lube System Male Tube w/yoke & Lube System Half Female Guarding w/label Half Male Guarding Half Female Shaft w/guarding Half Male Shaft w/guarding Decal, Danger - Outer Tube Decal, Danger - Outer Guard Tube BH Locknut, M10 x A--1

24 u q e w r 1* t 1* e w 1& i 1^ o 1) 1! 1# 1@ 1! 1$ 1% y CENTER DRIVESHAFT 1-/ 20 Spline Manufactured by Comer / EG Yoke w/grease Nipple Cross Journal Set Grease Nipple Capscrew, M12 x 1.25 x 80 Gr w/locknut M Retaining Washer Complete Disc Clutch Grease Nipple Spring Flanged Yoke Bushing Lining Ring Tapered Pin Set 1-/ Clutch Support Inner Plate Pressure Plate BH Capscrew, M10 x 1.5 x BH Locknut, M10 x Flanged Yoke, Male Flanged Yoke, Female 1 95A--2

25 SP C.V. Driveshaft Input : 1-/ 20 Spline, ASAE Size 5 Manufactured by Comer / EG 12815R2 & 12810R2 (1000 RPM Models) Complete Collar Yoke (Tractor) Cross Journal Set Grease Nipple 7657 Wide Angle Double Yoke Outer Yoke Roll Pin For Outer Tube Wiper Complete Outer Tube Cross Journal Set BH Complete Yoke Screw Kit Bearing Ring Guard Retaining Collar For Outer Tube Bolt Guard Retaining Collar For Inner Tube Safety Chain Guard Cone Set Complete Guard w/instruction Manual Tapered Pin Set 1-/ Female Tube w/yoke & Lube System Male Tube w/yoke & Lube System Half Female Shaft w/guarding Half Male Shaft w/guarding Decal, Danger - Outer Tube Decal, Danger - Outer Guard Tube Plastic Cap Kit Collar For Yoke 1-/ 1 95A--

26 SP C.V. Driveshaft Input : 1-/8 6 Spline, ASAE Size 5 Manufactured by Comer / EG 2815R2 & 2810R2 (50 RPM Models) Complete Yoke Cross Journal Set Circlip Grease Nipple Wide Angle Double Yoke Outer Yoke Roll Pin - Outer & Inner Tube Wiper Complete Outer Tube Inner Tube Roll Pin For Inner Tube Inner Yoke Cross Journal Set BH Complete Yoke Guard Cone Screw Kit Bearing Ring Guard Ret. Collar - Outer Tube Bolt Guard Ret. Collar - Inner Tube Safety Chains Guard Cone Set Complete Guard w/inst. Manual Outer Circlip Sliding Sleeve Collar Spring Fixed Sleeve Ball, 1/ Yoke Tapered Pin Set 1-/ Female Tube w/yoke Male Tube w/yoke Half Female Guarding w/label Half Male Guarding Half Female Shaft w/guarding Half Male Shaft w/guarding Decal, Danger - Outer Tube Decal, Danger - Outer Guard Tube Plastic Cap - Outer Tube Plastic Cap - Inner Tube Kit Collar For Yoke 1-/8 1 95A--

27 SP C.V. Driveshaft Input : 1-/8 21 Spline, ASAE Size 5 Manufactured by Comer / EG 12815R2 & 12810R2 (1000 RPM Models) Complete Yoke Cross Journal Set Circlip Grease Nipple Wide Angle Double Yoke Outer Yoke Roll Pin - Outer & Inner Tube Wiper Complete Outer Tube Inner Tube Inner Yoke Cross Journal Set Circlip Complete Yoke Guard Cone Screw Kit Bearing Ring Guard Ret. Collar - Outer Tube Bolt Guard Ret. Collar - Inner Tube Safety Chains Guard Cone Set Complete Guard w/inst. Manual Outer Circlip Sliding Sleeve Collar Spring Fixed Sleeve Ball, 1/ Yoke Tapered Pin Set 1-/ Female Tube w/yoke Male Tube w/yoke Half Female Guarding w/label Half Male Guarding Half Female Shaft w/guarding Half Male Shaft w/guarding Decal, Danger - Outer Tube Decal, Danger - Outer Guard Tube Plastic Cap - Outer Tube Plastic Cap - Inner Tube Kit Collar For Yoke 1-/8 1 95A--5

28

29 TONGUE, LEVELING ROD & RELATED PARTS FOR 2815R2, 2810R2, 12815R2 & 12810R2 MODELS Sleeve Bushing Clevis Pin Cotter Pin, /16 x Flatwasher, 1 SAE Capscrew, 1 x 5-1/ Locknut, Leveling Rod Assy Rod Weldment Turnbuckle Turnbuckle End Hex Jam Nut Tongue Weldment Bracket, Jack Weldment Mount Pad BH Capscrew, / x Jackstand Lockwasher, / Hex Nut, / 2 19 D82 Decal, Warning Washer, Jack Safety Tow Chain 1 95A-5-1

30 1 2 5 DRIVELINE HOLDER ASSEMBLY For 2815R2, 2810R2, 12815R2 & 12810R2 Models Mounting Bracket Weld Formed Driveline Holder Tie-Down Strap Capscrew, 5/8 x Flatwasher, 5/8 SAE Lockwasher, 5/ Hex Nut, 5/ SP SWIVEL PIVOT HITCH ASSEMBLY For 2815R2, 2810R2, 12815R2 & 12810R2 Models SP Swivel Pivot Hitch Assy Collar BH Capscrew, 5/8 x -/ Gr BH Locknut, 5/ Pin Weldment Capscrew, /8 x 2-1/ Gr Locknut, / Clevis Assembly Hitch Assembly Direction Decal Patent Decal Direction Decal 1 95A-5-2

31 AXLES & RELATED PARTS FOR 2815R2, 2810R2, 12815R2 & 12810R2 MODELS Center Axle w/wear Bearings Wing Axle w/wear Bushings R.H Wing Axle w/wear Bushings L.H Wear Bushing Pin, Pivot, 1 x Pin, Pivot, 1 x Pin, Pivot, 1 x BH Capscrew, /8 x 2 Gr BH Locknut, / Clevis Pin Cotter Pin, /16 x Flatwasher, 7/8 SAE Reflector, Amber Turnbuckle Swivel Assy (15-19) Rod Eye, Threaded Rod Eye, Swivel Turnbuckle Body Locknut, 1-1/ BH Grease Fitting Capscrew, 1 x 5-1/2 Gr Spacer, Locknut, Nord-Lockwasher, 1-1/ Lockwasher, BH Capscrew, 1 x -1/2 Gr Transport Lockout Assy U-Bolt, Foot Platform 1 28 D5 Decal, Important Hex Nut, / Locknut, / Cylinder Pin, 5-5/8 Lg Roll Pin, 1/ x 1-/ BH Flatwasher, A-5-

32 AXLE ARMS & RELATED PARTS SINGLE & DUAL SPINDLE FOR 2815R2, 2810R2, 12815R2 & 12810R2 MODELS Single Spindle Axle Arm L.H Single Spindle Axle Arm R.H Dual Axle Arm Pin Weldment Cup, Spring Cushion, Rubber Spring, Coil Spring Stop Capscrew, 1 x 7-1/2 Gr BH Locknut, 1 Flanged BH Capscrew, /8 x 1-1/2 Gr BH Locknut, / BH Capscrew, 1/2 x Gr BH Lockwasher, 1/ BH Locknut, 1/ Axle Tube Weldment w/grease Fitting Single Spindle Axle Dual Spindle Axle Hub Assy w/cups, Lug Bolts, Nuts & Grease Fittings BH Grease Fitting Lug Bolt BH Lug Nut Seal, Grease BH Bearing Cone Flatwasher, / SAE BH Slotted Nut, / NF Cotter Pin Hub Cap Bearing Cup Bearing Repair Kit 1 95A-5-

33 TANDEM AXLE ASSEMBLY FOR 2815R2, 2810R2, 12815R2 & 12810R2 MODELS Tandem Axle Assy L.H. (Shown) Tandem Axle Assy R.H Tube Assy w/grease Fittings Spindle Weldment L.H. (Shown) Spindle Weldment R.H Pin Weldment Flatwasher, 1-1/ Spiral Pin, /8 x 2-1/ Hub Assembly Bearing Cup BH Capscrew, /8 x 2-1/2 Gr BH Locknut, 1 Flanged Lug Bolt BH Lug Nut BH Grease Fitting Seal BH Bearing Cone, Inner Locknut, / Hub Cap Cotter Pin, 1/8 x 1-1/ BH Nut, Slotted, / NF Flatwasher, / SAE Spindle, ( Long) Spindle, 9.82 (Short) BH Capscrew, 1/2 x -1/ Locknut, 1/ BH Lockwasher, 1/ BH Grease Fitting Spring Bushing Bearing Repair Kit Pin Weldment Spring Cup Rubber Cushion Spring, Coil Capscrew, 1 x 7-1/2 95A-5-5

34 29SP SOLID TIRE ASSEMBLY Models: 2815R2, 2810R2, 12815R2 & 12810R SP FOAM FILLED AIRPLANE TIRE ASSY. 26 x 6.6 x Foam Filled Tire Assembly 26 x 6.6 x A-5-6

35 SP AIRPLANE TIRE ASSEMBLY Models: 2815R2, 2810R2, 12815R2 & 12810R BH Tire 29 x /16 Ply Tube 9 x Wheel Flange w/vave Hole Wheel Flange w/o Valve Hole Capscrew, 1/2 x 1 Gr Lockwasher, 1/ Hex Nut, 1/ A-5-7

36

37 BAFFLE KIT FOR 2815R2, 2810R2, 12815R2 & 12810R2 MODELS Baffle Weldment R.H. Wing Baffle Weldment L.H. Wing (2815, Only) Baffle Weldment L.H. Center Baffle Extension R.H. Center Baffle Extension L.H. Wing (2815, Only) Baffle Extension L.H. Center Baffle Extension R.H. Wing Baffle Weldment R.H. Wing Carriage Bolt, /8 x 1-1/2 Gr Lockwasher, / Hex Nut, /8 9 95A-6-1

38

39 HYDRAULICS FOR 2815R2, 2810R2, 12815R2 & 12810R2 MODELS WHEN PLUMBING TO TRACTOR REMOTES Wing Lift Cylinder Axle Control Cylinder Hydraulic Hose Assy. 228" Hydraulic Hose Assy. 196" Elbow 90 degree Breather Plug Restrictor,.078 Orfice Stop Kit Rod,Hose Holder BH Adaptor 9/16 JIC to / SAE 2-6- Adaptor 9/16 JIC to 1/2 NPT Capscrew, 5/8 x 2 Gr Flatwasher, 5/ Lockwasher, 5/ Hex Nut, 5/ Cylinder Pin, 6-5/8 Lg Roll Pin, 1/ x 1-/ 2 95A-7-1

40 Cylinder Assembly Part Number Stamped Here AXLE HYDRAULIC CYLINDER.5 Bore X 8 Stroke 1.25 Rod Diameter / 16 ORB Ports Manufactured by Monarch 9956 WING HYDRAULIC CYLINDER Bore x 12 Stroke 1.25 Rod Diameter / 16 ORB Ports Manufactured by Monarch Clevis Cap Rod Cap Piston Rod 1.25 Dia Cylinder Tube Tie Rod Pin, 1 Dia Cotter Pin, /16 x 1-1/ Thread Lock Rod Clevis, 1.25 x Set Screw, /8 x 1/2 Knurled Hex Nut, 5/8 UNF Hex Nut, Plug, / Decal, Caution Seal Kit Clevis Cap Rod Cap Piston Rod 1.25 Dia Cylinder Tube Tie Rod Pin, 1 Dia Cotter Pin, /16 x 1-1/ Thread Lock Rod Clevis, 1.25 x Set Screw, /8 x 1/2 Knurled Hex Nut, 1/2-1 UNC Hex Nut, Plug, / Decal, Caution Seal Kit 1 95A-7-2

41 DECAL KITS FOR 2815R2, 2810R2, 12815R2 & 12810R2 MODELS Decal Kit For 2815R2/12815R Decal Kit For 2810R2/12810R Decal, Amber Reflector Decal, Red Reflector Decal, Bush Hog Logo Decal, Important Decal, Model Decal, Model Decal, Model Decal, Model D57 Decal, Danger (50 RPM) 1 7 D59 Decal,Sheet Decal, Important 1 9 D552 Decal, Blade Rotation CW 1 10 D551 Decal, Blade Rotation CCW 2 11 D55 Decal, Warning 1 12 D555 Decal, Danger 2 1 D5 Decal, Important 1 1 D565 Decal, Danger 2 15 D56 Decal, Danger 16 D61 Decal, Danger (Thrown Object) 6 17 D559 Decal, Gen. Bush Hog Parts 1 18 D587 Decal, Lube 1 19 D58 Decal, Warning (1000 RPM Overlay) 1 20 D81 Decal, Danger - Multilingual 1 95A-8-1

42

43

44 2501 GRIFFIN AVE. SELMA, AL 670 () () PARTS ORDERING FAX