Solatube SolaMaster Series

Transcription

1 Soltue SolMster Series Soltue 330 DS 0-10V Low Voltge Dylight Dimmer Soltue 750 DS 0-10V Low Voltge Dylight Dimmer Instlltion Instrutions Prts List Quntity V Dylight Dimmer (1) 1 2 Dylight Dimmer Srew nd Fstener Kit. Srew #8 X 3/8 in (9.5 mm) (2) B. Srew #8 X 5/8 in (16 mm) (2). Foil Tpe 2in (50 mm) 6ft (1.82m) (1) 83 UL Listed Clss 2 Trnsformer 24VAC, Rted 96VA, or 24VAC, Rted 20VA *Sold Seprtely y Soltue Int. or Equivlent Soured Lolly Note: Red ll Instrutions to Choose Approprite Trnsformer. (1) 2 2 Additionl Mterils nd Tools 1 Srew Gun with Phillips #2 Srew Drive Bit 2 Preision Srewdrivers Slotted 2.5M & 1.8M 3 Juntion Box 4 in (100 mm) X 4 in (100 mm) X 1-1/2 (38 mm) with Ground Bonding Srew. Note: Required for Trnsformer Mounting nd Connetion. 2 *Components shown not inluded in ll kits, see lel on ox. 3 1

2 WARNING Do not proeed with the instlltion until you hve red the entire instrutions, inluding these wrnings. (Use of mterils or methods not uthorized y Soltue Interntionl will result in n invlid wrrnty.) Soltue Interntionl, In. (seller) ssumes no responsiility or oligtion whtsoever for the filure of n rhitet, ontrtor, instller, or uilding owner to omply with ll pplile lws, ordinnes, uilding odes, eletril odes, energy odes, fire nd sfety odes nd requirements, roof wrrnties nd dequte sfety preutions. Instlltion of this produt should e ttempted only y individuls skilled in the use of the tools nd equipment neessry for instlltion. Protet yourself nd ll persons nd property during instlltion. If you hve ny dout onerning your ompetene or expertise, onsult qulified expert efore proeeding. Instll t your own risk! Soltue produt instlltions my e dngerous nd inlude the potentil for deth, personl injury nd property dmge. The hzrdous onditions inlude ut re not limited to the following: During instlltion, the Soltue Dylighting System s refletive tues my fous sunlight, using intense het or fire. Remove protetive film only fter the prts hve een instlled. Prior to nd during instlltion, do not leve tues in ontt with omustile mterils or unttended, espeilly ner diret sunlight. Avoid skin urns. Do not leve deris from instlltion proess unttended. Srp from tuing nd foil tpe re highly refletive nd if left unttended n fous sunlight nd n use intense het or fire. Clen up ll unused mteril nd trsh nd store or disrd in proper overed lotions. Soltue Dylighting System nd Solr Str produts my hve shrp edges. Alwys wer lether or nvs gloves while hndling nd instlling produts. Soltue produt instlltions require liming nd working t dngerous heights, inluding on ldders, sffolding, roofs nd in tti spes. Risk of deth, personl injury nd property dmge my result from fll, or from flling ojets. Use extreme ution to minimize risk of identl injury, inluding, ut not limited to the following proedures: Cler re elow your work spe of ll people, nimls nd other items. Avoid working on surfes tht re slippery or wet. Use foot-wer with exellent trtion. Use only strong, well supported ldders. Work only in lm dry wether. When in the tti, ensure tht your weight is supported t ll times with struturlly sound frming; drywll mteril is not designed to rry person s weight. To redue the risk of fire, eletri shok, nd personl injury, si sfety preutions should lwys e followed when using eletri tools, inluding lwys wering sfety goggles or other suitle eye protetion, nd ensuring work re is ler of ll eletril wires, gs pipes, wter pipes, nd other ostles. When working in the tti or other dusty res, use of msk or respirtor is reommended to void lung irrittion. Atti spes my e drk, onfined, nd sujet to extreme tempertures. Bewre of shrp protruding ojets. Do not ttempt instlltion without hving someone within rnge of your voie or lose enough to ome to your id if neessry. Soltue produts re not designed to withstnd the weight of person, tools or other ojets. Wlking or pling ojets on the system ould use personl injury nd property dmge. If the produt is dmged, the struturl pity my e wekened; therefore the system should e repired immeditely. For sfe instlltion nd use, do not devite from these instlltion instrutions. Additionl support is reommended for long vertil nd ll horizontl tue runs. Review lol uilding requirements nd onsult with pproprite uilding ode offiil for proper mteril nd plement of dditionl support. Avoid glvni retion (orrosion) if dissimilr metls re used. Eletril Components Before instlling, serviing, or lening unit, swith power off t servie pnel nd lok servie pnel to prevent power from eoming swithed on identlly. When the servie disonneting mens nnot e loked, seurely fsten prominent wrning devie suh s tg to the servie pnel. Re-Roofing Soltue produts require speil re if removed for re-roofing. In order to ensure proper removl nd re-instlltion, plese ontt your Soltue Interntionl representtive. Plese refer to the instlltion tips for the pproprite produt elow: Dylighting Systems Instlltion Tips These instrutions re step-y-step guide for the instlltion of Soltue Dylighting System in the following onditions. For other roof types, plese ontt your Soltue Interntionl representtive for dditionl informtion. Built Up Flt Roof - Single Ply/Memrne - Asphlt Shingle - Low/No Pithed - Pithed - Prefrited Curs - Metl Roof Pnels 2

3 Dylighting Systems Instlltion Tips (Continued) Allow t lest 2-3 hours for the instlltion, prtiulrly if this is your first instlltion. During the dy, turn off ll the lights in the room to see how muh nturl light omes in through the windows, nd determine the est position for the Soltue Dylighting System. To light speifi re, ple the system over the re, not in the enter of the room. This will prevent the desired re from eing shded y tll ojets in the room. Mesure the distne etween the roof nd the eiling. If you don t hve enough tuing, ontt your Soltue Interntionl representtive for dditionl tuing. Avoid roof lotions shded y trees, ridges nd himneys, or ner wter hnnels or vlleys. Also void roof res with ostrutions suh s fire sprinklers, HVAC equipment, gs, wter or drin pipes, ir duts or flues nd mke sure tht the roof is dequte to endure n instlltion without dmging its wterproofing properties or wekening the uilding struture. All dhesives, sels nd tpes re reommended to e pplied to len nd dry surfe t minimum of 70 F (21 C) for mximum performne. Foil tpe ontins pressure sensitive dhesive nd pressure must e pplied t ll sems for proper onding. Foil tpe is not intended for use s struturl support of the extension tues. For struturl integrity use mnufturer supplied fsteners on ll overlpping extension tue joints. Uninstlled produt tht is stored nd exposed to exessive het nd or humidity n experiene dmge. Store produt prior to instlltion in ool dry ple. For instlltions where high levels of suit or deris my e present it my e neessry to use foil tpe to sel the diffuser to the tuing to prevent the exess deris from entering the tuing. Dylight Dimmer Instlltion Tips Plese follow ll lol muniipl nd uilding ode requirements prior to mking eletril onnetions. WARNING: To void risk of fire or eletri shok do not onnet high voltge to the power input terminl on the Soltue 0-10v Dylight Dimmer. CAUTION: To void dmge to the Dylight Dimmer Ciruit Bord use only 9V ttery to mnully operte dmpers. See Optionl Step on pge 8. Generl Ciruit Limittions: (7) Soltue Dylight Dimmers per 20VA trnsformer nd (17) Soltue Dylight Dimmers per 96VA trnsformer. Mx le length etween units 60 ft (18.29 m) for mximum of 50 Soltue Dylight Dimmers per ontroller. Ensure Plement of Dylight Dimmer Juntion Box is uniform for ll units in instlltion for ese of wire onnetion nd for est esthetis. For ese of wire onnetion to terminl loks do not strip wire more thn 3/16. Segregte power nd signl les entering into juntion ox to void rossover noise. Also, ross the ontrol lines nd the power lines perpendiulr inside juntion ox to void noise. Avoid umping pitors on PCB (Printed Ciruit Bord) to redue risk of dmge. If pitors re umped nd eome loose, reple entire juntion ox s improper funtionlity of Dylight Dimmers is highly prole. Importnt Souring Notes The Soltue 0-10v Dylight Dimmer is dylight tutor. It is importnt to soure ontrols for n tutor rther thn dimmer. The Soltue 0-10v Dylight Dimmer does not hve lod to ontrol. If using ontrols tht re equipped with n internl/externl rely or lod ontrol, it will e neessry to use n dditionl 20VA trnsformer to ontrol the system (see wire shemti t the end of these instrutions). 3

4 Trouleshooting Issue Possile Cuses Suggestions Dylight Dimmer(s) do not open or lose Dylight Dimmer(s) do not open or lose ompletely Wire/Connetion Issue Lighting Control System Trim Ostrution Wire/Connetion Issue Chek tht line voltge Ciruit is ON. Chek line voltge wire onnetions to Lighting Controller nd Trnsformer Chek low voltge power nd ontrol wire onnetions to terminl loks. Trim is not orretly set on lighting ontrol wll swith. See ontrol mnufturer's speifition for djusting trim. Remove Dome & Diffuser to inspet for ostrution inside tue preventing dmpers from opening or losing ompletely. Remove ll ostrutions. Chek wire onnetions to ensure ll line, neutrl, ground les re onneted orretly. Line voltge If it is determined tht line voltge hs een so onneted nd onneted to Dylight energized, ll Dimmer Controllers my e ompromised nd must Dimmer inputs e repled. Ensure tht trnsformer is onneted diretly to Supply Line. One or more Dylight Dimmer(s) in series osillte without hnge in lighting ontrol ommnd Wiring/Connetion Issue Wiring-Grounding Connetion Review nd test the first funtioning Dylight Dimmer in series prior to the osillting unit. Chek ll wires re properly onneted. Ensure ll strnds re in terminl loks; no strnds re loose or protruding from terminl onnetion. One finished move on to the next Dylight Dimmer in series nd repet proess. Test eh Dylight Dimmer efore moving on. Chek wire onnetions t ontroller to ensure ll line, neutrl, ground nd lod re onneted orretly. Chek ground onnetions t trnsformer nd Juntion Box. Dmged omponent on PCB Using Multimeter, hek for AC Voltge etween (+ & -) pins on CNTR IN nd CNTR OUT terminls. If >0.05VAC, review Printed Ciruit Bord (PCB) to see whether ny omponents hve een ompromised (during instlltion). If Cpitors or Terminl Bloks re loose or missing, reple entire J-Box. Lst unit not s open s first unit or ll units not t sme position. Units losest to power trnsformer open fster thn units frther from trnsformer. Wiring Connetion & Cle Length Mke sure you hve properly tthed signl wires from unit to unit. Chek In & Out ssignments nd polrity. Mke sure you hve not exeeded mximum distne from either, unit to unit, or soure to unit. Trnsformer Quntity My hve exeeded the mximum numer of units reommended for Dylight Dimmer Model or Trnsformer VA Rting. 4

5 Closed Ceiling Instlltion Instrutions 1 Instll 0-10V Dylight Dimmer to Trnsition Box Srew #8 X 5/8 in Pre Drill Srew #8 X 5/8 in Dylight Dimmer Trnsition Box 2 Instll Bottom Tue to 0-10V Dylight Dimmer Srew #8 X 3/8 in Bottom Tue Srew #8 X 3/8 in d 3 Tpe Dylight Dimmer nd to Trnsition Box 4 Remove Juntion Box Cover Foil Tpe Go to Pge 8 for Wiring Instrutions. 5

6 Open Ceiling Instlltion Instrutions 5 Instll 0-10V Dylight Dimmer to Extension Tue Ensure Extension Tue rests on top of Ts on Dylight Dimmer to ensure proper opertion of Dylight Dimmer fins NOTE: If Extension Tue is not resting on top of ts the Fins on the Dylight Dimmer my ind nd my not llow the Dylight Dimmer to operte Dylight Dimmer T Extension Tue Dylight Dimmer T Adjust Tue dimeter for proper fitment onto Dylight Dimmer Tue Ring Alternte Atthment It my e neessry to ut/djust tuing to meet proper overll tue length in some pplitions 6 Fsten Dylight Dimmer to Extension Tue Remove Juntion Box nd Hold for Lter Steps Srew #8 X 3/8 in Srew #8 X 3/8 in d 6

7 Open Ceiling Instlltion Instrutions Continued 7 Instll Extension Tue to Dylight Dimmer Foil Tpe Srew #8 X 5/8 in Srew #8 X 5/8 in 8 Instll Assemly into Roof Cur 9 Instll Sper on k side of Dylight Dimmer Juntion Box Sper 10 Instll Juntion Box to Dylight Dimmer Ring Ensure Dylight Dimmer Dmpers re returned to the full losed position efore repling juntion ox. Seure Juntion Box using provided srews. 7

8 The Following Instrutions Should Only Be Performed By A Liensed Eletriin Note: Plese follow ll lol muniipl nd uilding ode requirements prior to mking eletril onnetions. 11 Determine Approprite Trnsformer Mximum Dylight Dimmer Unit QTY / Trnsformer Trnsformer 20VA 96VA Mx QTY Option 1 Instll 24VAC, Rted 20VA Trnsformer nd Connet Power (Mx 7 Dylight Dimmers) Connet wires with pproprite voltge onnetion. Juntion Box Provided y Others Mke pproprite wire onnetions for supply voltge. Mke pproprite wire onnetions for power le: Trnsformer Red Blk Whit Power Supply Line Line Voltge Cp ll unused wires. Ground Ensure good ond to Erth Ground. Ground Metl Juntion Box (Provided y Others) 11 Wrning: Risk of fire or eletri shok. Do not onnet line voltge to the low voltge side of the trnsformer. Do not onnet high voltge to input terminl (power) on Soltue Dylight Dimmer. Option 2 Instll 24VAC, Rted 96VA Trnsformer nd Connet Power (Mx 17Dylight Dimmers) Connet wires with pproprite voltge onnetion. Juntion Box Provided y Others Mke pproprite wire onnetions for supply voltge. Mke pproprite wire onnetions for power le: Trnsformer Red Blk Whit Power Supply Line Line Voltge Cp ll unused wires. Ground Ensure good ond to Erth Ground. Ground Metl Juntion Box (Provided y Others) Note: Instlltion shown with Soltue supplied Trnsformer. If souring trnsformer from others plese follow wiring instrutions provided from trnsformer mnufturer. 8

9 13 Reple Juntion Box Cover Seure Dylight Dimmer Juntion Box Cover with 4 provided srew fsteners. Optionl Step Note: If it is neessry to open the Dylight Dimmer Dmpers prior to eletril onnetion, Use only 9V ttery to operte Dmpers. A lrger power ttery or power supply will dmge the PCB ord. Test Point Terminls 9V Bttery Only use 9V ttery to prevent dmge to PCB. The Following Instrutions Should Only Be Performed By A Liensed Eletriin Note: Plese follow ll lol muniipl nd uilding ode requirements prior to mking eletril onnetions. Generl Ciruit Limittions: (17) Soltue Dylight Dimmers per Trnsformer, Mx Cle Length etween Units 60 ft (18.29 m). Mximum 50 Soltue Dylight Dimmers per ontroller. 9

10 10

11 11