Solatube Brighten Up Series

Transcription

1 2 Soltue Brighten Up Series Soltue 60 DS Dylighting System Soltue 290 DS Dylighting System Instlltion Instrutions Prts List * Quntity Dome with Ryender 3000 Tehnology (). Shok Inner Dome* 2 Roof Flshing (pithed or no pith) () Top Tue Assemly inluding: Dome Ring, Dome Ring Sel, Spetrlight Infinity Top Tue with Angle Adpter. Spetrlight Infinity 6 in (400 mm) Extension Tue (not inluded in some kits, see lel on ox) Bottom Tue Assemly inluding: Spetrlight Infinity Bottom Tue with Angle Adpter, Ceiling Ring 6 Effet Lens () 7 Diffuser () Sel nd Fsteners. Dome Ring Srews - #8 X.25 in (32 mm) (5) () (2) (). LightTrker Refletor () 3 8d 8. Flshing Srews - #0 X 2 in (5 mm) (8) d. Roof Selnt () e. Expnsion Joint Sel () f. Tue Srews - #8 X 9/6 in (4 mm) (0) g. Foil Tpe - 2 in (5 mm) X 8 ft (5.5 m) roll () h. Drywll Srews - #6 X 5/8 in (40 mm) (4) 4 8e Required Tools: Keyhole Sw Ser or Reiproting Sw 8f Hmmer Flt Br Utility Knife Tpe Mesure 5 8g Culking Gun Srew Gun with Phillips Hed Lumer Cryon Mgneti Compss Required Sfety Equipment 6 7 8h Ceiling Selnt (White Aryli Ltex Culk or Equivlent) Not Provided Optionl (See Step 4) *Components shown not inluded in ll kits, see lel on ox. * High Veloity Hurrine Zones: Shok Inner Dome must e instlled with dome. To meet HVHZ requirements, use six inh no pith flshing or pithed flshing with four inh turret extension. For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE 205 Soltue Interntionl, In. Prt No v2.8

2 WARNING Do not proeed with the instlltion until you hve red the entire instrutions, inluding these wrnings. (Use of mterils or methods not uthorized y Soltue Interntionl will result in n invlid wrrnty.) Soltue Interntionl, In. (seller) ssumes no responsiility or oligtion whtsoever for the filure of n rhitet, ontrtor, instller, or uilding owner to omply with ll pplile lws, ordinnes, uilding odes, eletril odes, energy odes, fire nd sfety odes nd requirements, roof wrrnties nd dequte sfety preutions. Instlltion of this produt should e ttempted only y individuls skilled in the use of the tools nd equipment neessry for instlltion. Protet yourself nd ll persons nd property during instlltion. If you hve ny dout onerning your ompetene or expertise, onsult qulified expert efore proeeding. Instll t your own risk! Soltue produt instlltions my e dngerous nd inlude the potentil for deth, personl injury nd property dmge. The hzrdous onditions inlude ut re not limited to the following: During instlltion, the Soltue Dylighting System s refletive tues my fous sunlight, using intense het or fire. Remove protetive film only fter the prts hve een instlled. Prior to nd during instlltion, do not leve tues in ontt with omustile mterils or unttended, espeilly ner diret sunlight. Avoid skin urns. Soltue Dylighting System nd Solr Str produts my hve shrp edges. Alwys wer lether or nvs gloves while hndling nd instlling produts. Soltue produt instlltions require liming nd working t dngerous heights, inluding on ldders, sffolding, roofs nd in tti spes. Risk of deth, personl injury nd property dmge my result from fll, or from flling ojets. Use extreme ution to minimize risk of identl injury, inluding, ut not limited to the following proedures: Cler re elow your work spe of ll people, nimls nd other items. Avoid working on surfes tht re slippery or wet. Use foot-wer with exellent trtion. Use only strong, well supported ldders. Work only in lm dry wether. When in the tti, ensure tht your weight is supported t ll times with struturlly sound frming; drywll mteril is not designed to rry person s weight. To redue the risk of fire, eletri shok, nd personl injury, si sfety preutions should lwys e followed when using eletri tools, inluding lwys wering sfety goggles or other suitle eye protetion, nd ensuring work re is ler of ll eletril wires, gs pipes, wter pipes, nd other ostles. When working in the tti or other dusty res, use of msk or respirtor is reommended to void lung irrittion. Atti spes my e drk, onfined, nd sujet to extreme tempertures. Bewre of shrp protruding ojets. Do not ttempt instlltion without hving someone within rnge of your voie or lose enough to ome to your id if neessry. Soltue produts re not designed to withstnd the weight of person, tools or other ojets. Wlking or pling ojets on the system ould use personl injury nd property dmge. If the produt is dmged, the struturl pity my e wekened; therefore the system should e repired immeditely. For sfe instlltion nd use, do not devite from these instlltion instrutions. Additionl support is reommended for long vertil nd ll horizontl tue runs. Review lol uilding requirements nd onsult with pproprite uilding ode offiil for proper mteril nd plement of dditionl support. Avoid glvni retion (orrosion) if dissimilr metls re used. Eletril Components Before instlling, serviing, or lening unit, swith power off t servie pnel nd lok servie pnel to prevent power from eoming swithed on identlly. When the servie disonneting mens nnot e loked, seurely fsten prominent wrning devie suh s tg to the servie pnel. Re-Roofing Soltue produts require speil re if removed for re-roofing. In order to ensure proper removl nd re-instlltion, plese ontt your Soltue Interntionl representtive. Plese refer to the instlltion tips for the pproprite produt elow: Dylighting Systems Instlltion Tips These instrutions re step-y-step guide for the instlltion of Soltue Dylighting System in the following onditions. For other roof types, plese ontt your Soltue Interntionl representtive for dditionl informtion. Built Up Flt Roof - Single Ply/Memrne - Asphlt Shingle - Low/No Pithed - Pithed - Prefrited Curs - Metl Roof Pnels 2 For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE 205 Soltue Interntionl, In. Prt No v2.8

3 Dylighting Systems Instlltion Tips (Continued) Allow t lest 2-3 hours for the instlltion, prtiulrly if this is your first instlltion. During the dy, turn off ll the lights in the room to see how muh nturl light omes in through the windows, nd determine the est position for the Soltue Dylighting System. To light speifi re, ple the system over the re, not in the enter of the room. This will prevent the desired re from eing shded y tll ojets in the room. Mesure the distne etween the roof nd the eiling. If you don t hve enough tuing, ontt your Soltue Interntionl representtive for dditionl tuing. Avoid roof lotions shded y trees, ridges nd himneys, or ner wter hnnels or vlleys. Also void roof res with ostrutions suh s fire sprinklers, HVAC equipment, gs, wter or drin pipes, ir duts or flues nd mke sure tht the roof is dequte to endure n instlltion without dmging its wterproofing properties or wekening the uilding struture. All dhesives, sels nd tpes re reommended to e pplied to len nd dry surfe t minimum of 70 F (2 C) for mximum performne. Foil tpe ontins pressure sensitive dhesive nd pressure must e pplied t ll sems for proper onding. Foil tpe is not intended for use s struturl support of the extension tues. For struturl integrity use mnufturer supplied fsteners on ll overlpping extension tue joints. Uninstlled produt tht is stored nd exposed to exessive het nd or humidity n experiene dmge. Store produt prior to instlltion in ool dry ple. Dylight Dimmer Instlltion Tips Instll Soltue Dylight Dimmer only on properly ligned Soltue Dylighting System. Use only UL reognized omponents pproved for this listing. Light Add-On Kit Instlltion Tips This produt is to e instlled y qulified eletriins only. Disonnet power efore instlltion. FOR USE IN NON-FIRE-RATED INSTALLATIONS ONLY. Thermlly proteted TYPE IC (insultion my ontt housing). ACCESS ABOVE CEILING REQUIRED. SUITABLE FOR DAMP LOCATIONS. Use only s omponent of Soltue Dylighting System produts. MIN. 60 C SUPPLY CONDUCTORS. Intended for instlltion with ½ in (2.7mm) minimum sping from the fixture to vity surfes (side wll nd overhed uilding memer) nd in (25.4mm) minimum sping to djent fixtures. Blinking light my indite improper lmp wttge or type, or insultion is too lose to fixture, or other ondition using overheting. Cution Risk of fire nd eletril shok. Most dwellings uilt efore 985 hve supply wire rted 60 C. To redue the risk of fire, use only: Fluoresent Lmps, Medium Bse - 23 Wtt Mximum, Mximum Overll Length (MOL) 4 3/4 in (20 mm) Compt Fluoresent (4 Pin Qud Tue) 26 Wtt only Minimum thikness of metl tuing is 0.08 in (0.47mm) Ventiltion Add-On Kit Instlltion Tips See Ventiltion Add-On Kit instlltion instrutions for tips. Solr Str Atti Ventiltion Instlltion Tips Keep Solr Str solr pnels overed until produt is mounted nd seled to roof. Cover solr pnel whenever motor, fn, or unit is to e servied. Fn lde is ontrolled y the solr pnel nd my eome opertionl when pnel is exposed to sunlight. Solr Str produts re designed for generl ventiltion purposes only. Do not exhust ny hzrdous mterils or gses suh s flmmle, explosive or inendiry mterils. Solr Str produts hve n ungurded fn lde. Do not use Solr Str produts in res tht re esily essile. Cution Cron monoxide my e drwn into house or tti spe with the opertion of Solr Str produts if fuel-urning equipment is not servied or monitored regulrly. Cron monoxide (CO) is olorless, odorless gs tht n e hzrdous to your helth nd my use deth. Fuel-urning equipment must hve proper ventiltion, Solr Str produts re not designed to provide ventiltion for fuel-urning produts. For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE 205 Soltue Interntionl, In. Prt No v2.8 3

4 Mrk Ceiling nd Roof Lotion Between Joists nd Rfters Using Nils. Cut Ceiling Hole. Minimum lerne of 5 3/8 in (40 mm) for 60 DS nd 7 3/8 in (90 mm) for 290 DS etween nil hole enter nd joist. Roof Nil Nil 60 DS 5 3/8 in (40 mm) 290 DS 7 3/8 in (90 mm) 60 DS Ø 0 3/4 in (275 mm) 290 DS Ø 4 3/4 in (375 mm) Ceiling 2 Center on Nil nd Tre Inside Flshing Bse 3 Cut Roof Opening /2 in (2.7 mm) Cut Line; /2 in (3 mm) Outside Tred Line Nil Tred Line 4 Remove Roof Shingles 5 Set Flshing Roof Underlyment Roof Underlyment Roof Selnt (3/8 in (0 mm) thik) 4 For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE 205 Soltue Interntionl, In. Prt No v2.8

5 6 Fsten Flshing to Roof nd Reple Shingles 7 Align Dome Ring nd Flshing Holes Flshing Srew Roof Underlyment 8 Align Top Tue Angle with Ceiling Opening 9 Remove nd Tpe Top Tue Tpe ll sems. 0 Fsten Top Tue to Flshing* Dome Instlltion Refletive side of LightTrker Refletor fes South in Northern Hemisphere (North in Southern Hemisphere). Align nd snp dome into ple engging ll four snps. Dome Ring Srew LightTrker Refletor Remove Protetive Liner Shok Inner Dome for HVHZ Remove Protetive Liner *For HVHZ dip srew threds in selnt For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE Soltue Interntionl, In. Prt No v2.8

6 2 Insert Bottom Tue Align nd mesure tue run. Minimum Overlp t Tue Sems /2 in (38 mm) Minimum Overlp t Tue Sems /2 in (38 mm) Tue length mesurements should e equl. 3 Assemle nd Instll Tue Run Use nothes to rete tpered tue. Apply pressure to tpe for proper onding Remove Protetive Liner Minimum Overlp t Tue Sems /2 in (38 mm) d g e f Insert ottom tue ssemly into top tue. Tue Srew Foil Tpe Expnsion Joint Sel h Apply foil tp to ll sems nd joints. 6 For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE 205 Soltue Interntionl, In. Prt No v2.8

7 4 Fsten to Ceiling Use drywll srews if fstening lmps do not engge eiling. Remove Protetive Liner Fstening Clmp Drywll srew if neessry 5 Instll Effet Lens nd Diffuser Diffuser Effet Lens 6 Now you n enjoy the enefits of your Soltue Dylighting System nd the high performne, nturl lighting it provides. Plese refer to the following setion for list of lterntive flshings nd essories. For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE Soltue Interntionl, In. Prt No v2.8

8 Cur Mounted Flshing Instlltion Instrutions Appendix Prts List 290 DS (4 in/350 mm) Cur Mounted Flshing (Inside Dimension 27 in (685 mm) X 27 in (685 mm)) Quntity () Additionl Mterils nd Tools Quntity Roof Selnt () 2 Flshing Srews #0 X 2 in (50 mm) (8) Apply Selnt to Cur Instll Cp on Cur 2 Cur y Others (llow for ounter flshing roofing mteril) 27 in (685 mm) inside dimension 27 in (685 mm) inside dimension 3 Fsten Flshing to Cur Flshing Srew *For HVHZ pply 4 more srews to ur p. 8 For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE 205 Soltue Interntionl, In. Prt No v2.8

9 Cur Cp Flshing Insultion Instlltion Instrutions Appendix Prts List Quntity 290 DS (4 in/350 mm) Cur Insultion (4) Additionl Mterils nd Tools Quntity Roof Selnt () 2 Foil Tpe () Apply Selnt to Underside of Cur Cp 2 Instll Insultion Apply mtte side of insultion to Cur Cp surfe. 3 Apply Foil Tpe to Sems For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE Soltue Interntionl, In. Prt No v2.8

10 Universl Tile Flshing Instlltion Instrutions Appendix (with Bse Flshing) Prts List Quntity Additionl Mterils nd Tools Quntity Tile Flshing (Pithed or No Pith version) () 2 Bse Flshing (Pithed or No Pith version) () 2 Aluminum L rket (4) Roof Selnt () 2 Flshing Srews #0 X 2 in (50 mm) srews (8) 3 Tile Grinder () 3 #8 X /4 in (6 mm) srews (8) Note: These instrutions re for non-hvhz res only. Contt Soltue Interntionl representtive for reommendtions in HVHZ res. Cution: The use of Portlnd Cement sed msti, grout, or lkline mterils will use dmge to the luminum flshing. Remove Tiles. Center on Nil nd Tre Inside Flshing Bse. 2 Cut Roof Opening Cut Line; /2 in (3 mm) Outside Tred Line Nil Tred Line Nil 3 Set Bse Flshing 4 Fsten Flshing to Roof Flshing Srew Roof Selnt (3/8 in (0 mm) thik) 0 For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE 205 Soltue Interntionl, In. Prt No v2.8

11 5 6 Set Universl Tile Flshing Bend front edge of Universl Tile Flshing to fit shpe of roof tiles. Fsten Universl Tile Flshing to Bse Flshing #8 X /4 in (6 mm) Srew Bse Flshing Universl Tile Flshing 7 Cut nd Reple Roof Tiles 8 Seure Flshing to Tile L-rket Flshing Edge #8 X /4 in (6 mm) Srew For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE 205 Soltue Interntionl, In. Prt No v2.8

12 Flt Roof Instlltion Instrutions Appendix Prts List Quntity Roof Flshing (no pith) () 2 Flshing Srews - #0 X 2 in (5 mm) (8) Additionl Mterils nd Tools Quntity Stright Edge () 2 Roof Selnt () Center on Nil. Tre Inside nd Outside Flshing Perimeter. 2 Cut Roof Opening Flshing Perimeter Nil Cut Line; /2 in (3 mm) Outside Tred Line Nil Tred Line 3 Apply Selnt to Roof nd Flshing 4 Set Flshing Roof Selnt 3/4 in (20 mm) thik Roof Selnt 3/4 in (20 mm) thik 2 For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE 205 Soltue Interntionl, In. Prt No v2.8

13 5 Fsten Flshing to Roof 6 Apply Selnt nd Spred Evenly Using Stright Edge Flshing Srew Roof Selnt 3/4 in (20 mm) thik Stright Edge Flshing Insultor Instlltion Instrutions Appendix Prts List Quntity Flshing Insultor () 2 Foil Tpe (8) Wrning: Do not expose Flshing Insultor to diret flme. Additionl Mterils nd Tools None Quntity Center Flshing Insultor on Flshing Bse. 2 Apply Foil Tpe. Apply pressure to foil tpe for proper onding. Return to min instrution set to omplete flshing instlltion. For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE Soltue Interntionl, In. Prt No v2.8

14 Turret Extension Instlltion Instrutions Appendix Prts List Quntity Turret Extension 2 in (50 mm) or 4 in (00 mm) () Additionl Mterils nd Tools Quntity Roof Selnt () 2 /4 in (6 mm) srews (4) Apply Selnt to Flshing nd Inside of Turret Extension 2 Ple Turret Extension over Flshing nd Fsten /4 in (6 mm) Srew Dome Edge Protetion Bnd Instlltion Instrutions Appendix Prts List Quntity Dome Edge Protetion Bnd () Additionl Mterils nd Tools None Quntity Ple Dome Edge Protetion Bnd Over Flshing 2 Seure Dome Edge Protetion Bnd With top tue instlled, lign with dome ring spers nd snp into ple. Bend ts up prior to instlltion 4 For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE 205 Soltue Interntionl, In. Prt No v2.8

15 0-90 Degree Extension Tue Instlltion Instrutions Appendix Prts List Quntity 0-90 Degree Extension Tue () 2 Tue Srews - #8 X 3/4 in (0 mm) (4) 3 Foil Tpe - 2 in (5 mm) X 6 ft (2 m) (4) Additionl Mterils nd Tools None Quntity Instll 0-90 Degree Extension Tue Instll only etween the top tue nd n extension tue or two extension tues. Foil Tpe Tue Srew Minimum overlp t tue sems /2 in (38 mm) Apply pressure to tpe for proper onding Additionl struturl support my e required for horizontl tue runs. Consult lol uilding ode. For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE Soltue Interntionl, In. Prt No v2.8

16 Soltue Brighten Up Series Aessories Add more funtion y upgrding your Soltue Dylighting System with ny of these gret essories. Light Add-On Kit When equipped with light dd on kit, the Soltue Dylighting System provides the onveniene of swithed light for night time use. Aville in n energy effiient ompt fluoresent design tht meets Cliforni Title 24 requirements nd in universl fixture. Dylight Dimmer Beuse you don t need 00% of the light 00% of the time, the innovtive Soltue Dylight Dimmer esily ontrols the mount of dylight entering room with the onveniene of swith. Our ptented vrile utterfly ffle ontrols the light output. Ventiltion Add-On Kit The Soltue 60 DS is ville with n optionl Ventiltion Add-On Kit. When omined with this innovtive essory, the 2-in- eiling fixture minimizes eiling penetrtions for more ttrtive look. Metl Roof Instlltion Kit Order this kit for instlltion of Soltue 60 DS or 290 DS flshing onto stnding sem metl roof. Universl Tile Flshing (for pplitions without se flshing) The Universl Tile Flshing integrtes semlessly with most tile profiles. The mllele flshing skirt, ville with pithed or no pith turret, esily dpts to the shpe of the tile. Dome Upgrde Kit Upgrde n older Soltue produt to tke dvntge of Soltue s ptented Ryender 3000 Tehnology. The dome upgrde kit is instlled without removing previous flshing or tuing. Re-Roofing Reommendtions Soltue produts require speil re if removed for re-roofing. Refer to the Soltue Re-Roofing Reommendtions to ensure proper removl nd re-instlltion. Not ll items ville for ll mrkets. Contt your Soltue Interntionl representtive for vilility. 6 For the most urrent Instlltion Instrutions, plese visit Soltue Interntionl, In. 220 Ok Ridge Wy Vist, CA T: 888.SOLATUBE 205 Soltue Interntionl, In. Prt No v2.8