OUTLET BOX MOUNTING INSTRUCTIONS

Transcription

1 OUTLET OX MOUNTING INSTRUTIONS HLTL2X10WLEDPT DO NOT TTEMPT INSTLLTION UNTIL YOU RE FMILIR WITH LL WRNINGS, PREUTIONS, ND PROEDURES OUTLINED WITHIN THIS INSTRUTION SHEET. TURN OFF POWER ELETRIL POWER MUST E OFF EFORE ND DURING INSTLLTION ND MINTENNE. LUMINIRE MUST E GROUNDED S REQUIRED PER PRGRPH ND RTILE 250 OF THE NTIONL ELETRI ODE ND/OR SETION 10 ND RULE OF NDIN ELETRI ODE. FILURE TO PROPERLY GROUND THIS LUMINIRE WILL RETE N ELETRIL SHOK HZRD WHIH N USE SERIOUS INJURY OR DETH. INSTRUTIONS FOR INSTLLTION NOTE: For suitable fixture support, consult National Electrical ode (NE) or anadian Electrical ode. FIXTURES MUST HVE MINIMUM OF FIVE FULL THRED ENGGEMENTS. INSTLLTION MUST E IN OMPLINE WITH LOL ND/OR NTIONL ODES. NOTE: OUTLET OX THREDS MUST E LURITED TO PREVENT GLLING. IF LURINT IS REMOVED, LIGHTLY LURITE WITH ORROSION INHIITING PETROLEUM SED GRESE SUH S PETROLTUM OR SOPTHIKENING MINERL OIL TO INSURE ESE OF FUTURE MINTENNE. PENDNT MOUNT Install pendant mount on conduit. Tighten set screw to 30 in.lbs. torque to prevent loosening. EILING MOUNT Install ceiling mount by means of four external mounting holes on 6" bolt circle. Plug unused conduit entries with closeup plugs. WLL OR ULKHED MOUNT Install wall or bulkhead mount by means of four external mounting holes in backplate so that threaded hub is extending downward. Plug unused conduit entries with closeup plugs. STNHION MOUNT Install stanchion mount on conduit. Tighten set screw to 30 inlbs. torque to prevent loosening. NOTE: For suitable supply wire, consult marking on fixture (ballast housing) for required temperature rating. Fixture mount must be grounded per applicable code referred to above. separate grounding screw in the outlet box is provided to install ground lead. heck ground continuity before energizing the fixture. Larson Electronics, LL Phone: (800) Fax: (903) /4

2 HLTL2X10WLEDPT LUMINIRES FOR HZRDOUS LOTIONS ND DVERSE ENVIRONMENTS DO NOT TTEMPT INSTLLTION UNTIL YOU RE FMILIR WITH LL WRNINGS, PREUTIONS, ND PROEDURES OUTLINED WITHIN THIS INSTRUTION SHEET. TURN OFF POWER ELETRIL POWER MUST E OFF EFORE ND DURING INSTLLTION ND MINTENNE. INSTLLTION PREUTIONS: 1. DO NOT INSTLL LUMINIRE IN NY LSSIFIED LOTION WHERE THE MRKED OPERTING TEMPERTURE EXEEDS THE IGNITION TEMPERTURE OF THE HZRDOUS TMOSPHERES. ONSULT LUMINIRE NMEPLTE FOR SUITILITY IN SPEIFI HZRDOUS LOTIONS. 2. DO NOT INSTLL LUMINIRE IN LOTION WHERE THE MIENT TEMPERTURE EXEEDS THE MXIMUM MIENT TEMPERTURE SHOWN ON THE LUMINIRE NMEPLTE. 3. REFER TO LUMINIRE NMEPLTE FOR MINIMUM SUPPLY WIRE TEMPERTURE RTING. 4. VERIFY THT THE SUPPLY VOLTGE GREES WITH LUMINIRE RTING S INDITED ON NMEPLTE. 5. LMP REEPTLE SREW SHELL MUST E T LOWEST POTENTIL (OR GROUND) 6. LL LOL, NE ND E ODES MUST E FOLLOWED WHEN INSTLLING THE LIGHTING LUMINIRE. FOR ODE INTERPRETTION, ONSULT YOUR LOL ODE UTHORITY. USE WIRING METHOD FOR LSS I & LSS II DIV.1. ND PER NE & E ODE. 7. LLST HOUSING MUST E SSEMLED WITH LISTED LUMINIRE FITTINGS S SPEIFIED ON THE NMEPLTE. THE MOUNTING OUTLET OX ND GLOE SSEMLY MUST FULLY ENGGE THE HOUSING WITH MININUM OF FIVE THREDS. REPLE RKED OR DMGED GLOE PRIOR TO USE. 8. VERIFY THT GROUND ONTINUITY HS EEN ESTLISHED Y USING N OHMMETER OR OTHER SUITLE TESTING EQUIPMENT EFORE ENERGIZING THE LUMINIRE. FILURE TO PROPERLY GROUND THE LUMINIRE WILL RETE N ELETRIL SHOK HZRD WHIH N USE SERIOUS INJURY OR DETH. DO NOT SRTH, SORE, NIK OR HIP THE GLSS GLOE. FIRE ND EXPLOSION HZRD. REKGE OF GLSS GLOE ND EXPOSURE OF LMP TO OMUSTILE TMOSPHERE N RESULT IN N EXPLOSION ND POSSILE INJURY OR DETH. LUMINIRE MUST E GROUNDED S REQUIRED PER PRGRPH ND RTILE 250 OF THE NTIONL ELETRI ODE ND/OR SETION 10 ND RULE OF NDIN ELETRI ODE. FILURE TO PROPERLY GROUND THIS LUMINIRE WILL RETE N ELETRIL SHOK HZRD WHIH N USE SERIOUS INJURY OR DETH. Larson Electronics, LL Phone: (800) Fax: (903) /4

3 HLTL2X10WLEDPT LUMINIRE LENING: Periodic cleaning of the globe assembly may be needed to maintain full lighting efficiency and to prevent excessive dust or dirt accumulation, which could cause the luminaire to operate at a higher temperature. leaning the luminaires components should be done with a nonabrasive solution of soap or detergent and water. Residual solution should be removed by clean water rinsing. NOTE: IF LURINT IS REMOVED FROM THREDS DURING MINTENNE OR RELMPING, LIGHTLY LURITE WITH ORROSION INHIITING PETROLEUM SED GRESE SUH S PETROLTUM OR SOPTHIKENING MINERL OIL. DISHRGE VESSEL REPLEMENT PROEDURES DISONNET THIS LUMINIRE FROM SUPPLY IRUITS EFORE REMOVING GLOE TO VOID EXPOSING HOT SURFES OR ELETRI RING TO HZRDOUS TMOSPHERE. DO NOT REENERGIZE UNTIL THE GLOE HS EEN REINSTLLED. FILURE TO OMPLY WITH THIS WRNING N USE FIRE OR EXPLOSION WHIH N RESULT IN SERIOUS INJURY OR DETH. 1. Loosen thumb set screw to allow globe assembly to turn freely. 2. Remove globe assembly. 3. FOR H.I.D. MODELS Remove H.I.D. lamp and/or optional quartz lamp. (NOTE: it may be necessary to remove the H.I.D. lamp to replace the optional auxiliary quartz lamp.) Verify that the H.I.D. lamp complies with lamp specifications on luminaire nameplate, then install. To install quartz auxiliary lamp, push and twist lamp into bayonet receptacle. FOR FLUORESENT MODELS Remove lamp(s). Verify that the replacement lamp complies with lamp specifications on luminaire nameplate, then install. To install fluorescent lamp, push lamp into bipin receptacle. 4. To reassemble globe assembly, refer to installation procedure. FILE THIS INSTRUTION SHEET FOR FUTURE USE Larson Electronics, LL Phone: (800) Fax: (903) /4

4 INSTRUTIONS FOR INSTLLTION Install luminaire outlet box () (per instructions supplied with outlet box fitting). Remove female contact assembly (E) from mounting bosses (). Pull supply wires () (use proper temperature rated wire See luminaire nameplate on ballast housing). NOTE: LUMINIRE MUST E GROUNDED. SEPRTE GROUNDING SREW IN THE OUTLET OX IS PROVIDED TO INSTLL GROUND LED. HEK GROUND ONTINUITY EFORE ENERGIZING THE LUMINIRE. HLTL2X10WLEDPT Install grounding lead (D) to grounding screw in outlet box. onnect line lead to terminal (G) marked "LINE". omplete circuit by attaching common or second line to terminal (F) marked "WHITE" in female contact assembly. Visually inspect connection. Return female contact assembly to outlet box and secure to mounting bosses (), with fasteners (H). NOTE: LL THREDS MUST E LURITED TO PREVENT GLLING. IF LURINT IS REMOVED, LIGHTLY LURITE WITH ORROSION INHIITING PETROLEUM SED GRESE SUH S PETROLTUM OR SOPTHIKENING MINERL OIL TO INSURE ESE OF FUTURE MINTENNE. Screw luminaire section (ballast housing) onto outlet box until hand tight. To secure luminaire section onto outlet box, tighten #1024 set screw to 30 in.lbs. (max.) torque. ENH SSEMLY assembly of item (K)(L)(M)(N)(P) may be performed on a bench to facilitate ease of installation. If luminaire was supplied with multitap ballast (indicated by more then one (1) ballast primary volts on luminaire, proper ballast voltage lead corresponding to supply voltage must be connected to luminaire lead labeled line with connector supplied. ll leads must be inserted into cable tie and secured in place. Unused primary wire must be insulated to prevent shorting. If luminaire is equipped with quartz auxiliary receptacle (J) install quartz lamp before H.I.D. lamp (H.I.D. luminaire only). Verify that the lamp(s) (L) complies with lamp specification on luminaire nameplate, then install. Screw globe assembly (M) (clockwise) onto luminaire section until hand tight. It may be necessary to back off globe assembly (counterclockwise) slightly, to allow thumb screw to enter nearest notch. To lock globe assembly in place, tighten thumb screw (K) into notch in globe retaining ring NOTE: WRNlNG NOTIE MUST E REMOVED FROM GLSS GLOE EFORE INSTLLTION. Install reflector (N) and/or globe guard (P) over three screws furnished in lower face of globe assembly. ack out screws sufficiently to allow reflector and/or globe guard to be inserted over screws and twist in place. Tighten screws to hold reflector and/or globe guard securely in place. DO NOT ENERGIZE THE LUMINIRE UNTIL THE GLOE SSEMLY ND MOUNTING OUTLET OX HVE EEN INSTLLED TO VOID EXPOSING HOT SURFES OR ELETRI RING TO HZRDOUS TMOSPHERE. FILURE TO OMPLY WITH THIS WRNING N USE FIRE OR EXPLOSION WHIH N RESULT IN SERIOUS INJURY OR DETH. Larson Electronics, LL Phone: (800) Fax: (903) /4

5 HLTL2X10WLEDPT INSTLLTION INSTRUTIONS FOR LUMINIRE MOUNTS DO NOT TTEMPT INSTLLTION UNTIL YOU RE FMILIR WITH LL PREUTIONS ND PROEDURES OUTLINED WITHIN THIS INSTRUTION SHEET. WRNING: Risk of Shock. Disconnect Power before Installation. LUMINIRE MUST E GROUNDED S REQUIRED PER PRGRPH ND RTILE 250 OF THE NTIONL ELETRI ODE ND/OR SETION 10 ND RULE OF NDIN ELETRI ODE. FILURE TO PROPERLY GROUND THIS LUMINIRE WILL RETE N ELETRIL SHOK HZRD WHIH N USE SERIOUS INJURY OR DETH. 1. PENDNT ND STNHION TYPE MOUNTS Screw the luminaire mount onto previously install conduit, a minimum of 3 threads must be engaged between the conduit and luminaire mount. Tighten the conduit locking screw () to 30 inch pounds (figure.1). Figure 1 2. EILING ND WLL TYPE MOUNTS Install the luminaire mount to the appropriate mounting surface by means of the external mounting lugs (). The bolt positions are as follows: a. eiling: 123/4 bolt circle for std 3 or 95/8 bolt circle for mini M3 b. Wall: 33/4 X 33/4 bolt pattern Install conduits plug in any unused conduit entries with the supplied closeup plugs (), minimum of 3 threads must be engaged between the conduit or closeup plug and luminaire mount. D Figure 2 Figure INH OUTLET OX TYPE MOUNTS Install the luminaire mount to previously installed 4 inch outlet box using supplied gasket and screws tighten mounting screws (d) to 30 inch pounds. lways inspect gasket joints before closing the luminaire, if gasket shows any indication of deterioration, replace the luminaire. Larson Electronics, LL Phone: (800) Fax: (903) /1