Silvus TM 30 Exterior
|
|
- Clement Benson
- 6 years ago
- Views:
Transcription
1 Components included Sconce and Mounting Plate with Locking Plate attached. Three wire connectors and one washer 30 fixture 60 fixture Marked Marked -to-module wiring cable included with (60 only) Marked 4 round cover plate with gasket/screws, attached to power cable on marked IMPORTNT: efore you begin, please read entire instructions. Specific instructions included for multiple fixture applications. Fixtures should be installed by a licensed electrician. Wall mount in vertical position only.
2 NOTE: Wall mounting hardware is not included due to the wide variety of wall materials. Customer should determine the appropriate anchoring hardware required for their specific needs. Ivalo Lighting recommends the use of #8 minimum mounting hardware. Total weights of fixtures are as follows: 30 : 24 lbs & 60 : 46 lbs. Tools required Level No. 2 x 8 Phillips screwdriver wl Preparation 1. Refer to model number label located on the rear of module marked. See sample below. Model label MODEL: SILVUS Sconce SED30LRG2WPULPS Sample Model Number: FIXTU RE LENGTH CONTROL OPTION SED- 30 -LRG2W- P -ULPS N- Non-Dim P- Pulse Using Fixture Length and Control Option codes found on model number label, determine correct wiring diagram for your installation. 2
3 Hot (120 V~) Neutral lack White Green -to-module wiring cable -to-module wiring cable -to-module wiring cable lack White 3
4 DMX Control CT5 RJ45 CT5 RJ45 CT5 RJ45 Hot (120 V~) Neutral lack White Green -to-module wiring cable -to-module wiring cable -to-module wiring cable lack White 2. Fixtures with length 030 consist of. Fixtures with length 060 consist of s &. Please note lens orientation when mounting fixtures to wall. Fixtures can be positioned in two different and unique ways. For 60 fixtures, lenses should form a connected, flowing pattern. 30 fixture 60 fixture OR OR 4
5 3. For 30 fixtures, place sconce face down on a protective surface and remove Top Locking Plate (Fig. 1a) from Mounting Plate (Fig. 1b) by removing screw. For 60 fixtures, remove Top Locking Plate from separately packaged Mounting Plate. Set Top Locking Plate and screw aside for later use. Figure 1a Figure 1b Mounting Plate Top Locking Plate 4a. On 30 fixtures, remove the Mounting Plate (Fig. 1b) by sliding toward the bottom and then pulling up. If unit has Pulse control option, remove Connector Plate (Fig. 1c) by taking out 2 screws. e careful not to tear gasket material. Figure 1c Connector Plate 4b. For 60 fixtures, remove Conector Plate (Fig.1c) from back of both modules by taking out 2 screws. e careful not to tear gasket material. 5
6 Installation 5. T rcuit breaker and light switch. 6. Remove cross-bar, if present, and screws from round or octagonal junction box. 7. Place Mounting Plate on wall in the desired location with the Top Locking Plate opening at the top. Make sure the junction box is within the perimeter of the top rectangular opening. 8. Level the Mounting Plate and mark the mounting locations at the top center of all keyhole slots with awl. The 30 have 4 keyhole slots, 60 have 8 keyhole slots
7 9. Remove Mounting Plate from wall and install anchoring hardware at all marked locations per the manufacturer s recommendation for the specific type of wall material. 10. Install screws leaving 1 4 spacing between screw head and wall surface. DO NOT install the top left screw. This will be installed later to hold a safety chain for inspection purposes. 1/4 11. Place Mounting Plate over the screw locations () and slide down over screws (). Tighten top right screw. Re-level Mounting Plate and then tighten remaining screws. Top view of mounting plate ottom view of mounting plate 7
8 12. Pull wires from junction box. 13. ttach safety chain located on the back of to the remaining mounting anchor location at top left of Mounting Plate. Use the provided washer and insert the anchor through the last link of the chain. Install at the top left keyhole slot in the Mounting racket. 14. Use wire connectors to make corresponding connections with power cord wires from junction box. Make sure junction box gasket is positioned over power cable so it will fit over wires when connections are made. White: neutral Green: ground C lack: power (120 V~) C 8
9 15. Push wire connections into junction box. With screws provided, attach cover plate and gasket to junction box. Make sure a good seal is made between gasket and junction box. Unit NOTE: For 30 fixtures with Control Option: Non-Dim no further wiring is required. Proceed to step 16b. 9
10 16a. ccess low voltage electrical connections for wiring. For fixtures requiring the optional Color Kinetics iplyer 3 DMX controller, attach category 5 control cable with RJ45 plug to either socket. It is the customer s responsibility to provide this control cable to the fixture installed according to all applicable codes. Route cable out bottom of opening. C Reattach Connector Plate with screws previously removed. C OR 16b. ttach to wall mounting plate by aligning the 4 slots on chassis rails with 4 horizontal pins located on sides of the Mounting Plate. Slide in and then down to secure in place. 10
11 Silvus TM Wiring configurations for 60 Fixtures: 60 Fixtures are comprised of two s mounted on one 60 frame. Note: lways mount on top and then below. Review lens diagram layout in Step 2. Unit Unit 17a. ccess low voltage electrical connections for wiring between modules. Connect Male end of -to-module wiring cable to. Route cable out bottom of opening. C Replace Control Plate with screws previously removed. D fter making a connection to, place the Female end of the -to-module wiring cable between the channel of the mounting plate. ttach to wall mounting plate by aligning the 4 slots on chassis rails with 4 horizontal pins located on sides of the mounting plate. Slide in and then down to secure in place. E Connect Female end of -to-module wiring cable to. F Reattach connector plate. Proceed to step 17c. Unit Unit D Unit C Unit E D F 11
12 Silvus TM Unit Unit 17b. Unit ccess low voltage electrical connections for wiring. Connect male end of provided -to-module cable to female socket. ttach category 5 control cable with RJ45 plug to either socket. It is the customer s responsibility to provide this control cable to the fixture installed according to all applicable codes. Route all cable out bottom of opening. C Replace Connector Plate with screws previously removed. D fter making a connection to, place the Female end of the -to-module wiring cable between the channel of the mounting plate. ttach to wall mounting plate by aligning the 4 slots on chassis rails with 4 horizontal pins located on sides of the mounting plate. Slide in and then down to secure in place. E Connect Female end of -to-module wiring cable to. F Reattach Connector Plate. Unit D C E D F or 12
13 17c. Mount to mounting plate in same manner as. 17d. Use long handled No. 2 x 8 Phillips screwdriver to lock in place. Rotate 1/4 turn clockwise. 18. Reattach the Top Locking Plate with screw previously removed. This prevents module from being inadvertently removed from Mounting Plate. 19. Turn on circuit breaker and light switch. 13
14 Technical Notes: THIS PRODUCT MUST E INSTLLED IN CCORDNCE WITH THE PPLICLE INSTLLTION CODE Y PERSON FMILIR WITH THE CONSTRUCTION ND OPERTION OF THE PRODUCT ND HZRDS INVOLVED. Warranty: For limited 10-year-warranty details, see For Help: For help with applications, installation, or if there are missing parts, please contact us at (610) or Lutron Electronics Co., Inc Suter Road Coopersburg, P 18036, US phone: (610) fax: (610) /2016 P/N Rev. 14
Customer service: or Upper mounting ring. Canopy
Components included: Upper mounting ring Canopy Fixture base Fluorescent - 2 x 42 W 4-pin compact fluorescent lamps required (not included). Lutron recommends GE, Sylvania, or Philips lamps that are certified
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS IMPORTANT Before opening your Lights.com fixture, please make sure that you carefully read through these instruction sheets. Consider having your fixture installed by a qualified
More informationINSTALLATION INSTRUCTIONS LIGHTPLANE 3.5. LP3.5 Suspended LED. A nd Avenue, Unit 1. CA P E W alwusa.
Oakland, INSTALLATION INSTRUCTIONS LIGHTPLANE 3.5 LP3.5 Suspended LED A 1035 22nd Avenue, Unit 1 n CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings! 1. Read all instructions.
More informationElle Surface Mounting Instructions
Step 1: Preparation, page 2 Warnings CAUTION risk of fire and this product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation
More information30in Phoebe Round Crystal Chandelier Assembly Instructions
CUTION: 30in Phoebe Round Crystal Chandelier ssembly Instructions BEFORE INSTLLING FIXTURE, MKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF T THE MIN FUSE BOX / CIRCUIT BREKER UTILITY BOX. THIS LUMINIRE
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS
ASSEMBLY AND INSTALLATION INSTRUCTIONS 348-0035 / 348-0036 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing,
More informationUpton LED Chandelier 40in Assembly Instructions
CUTION: Upton LED Chandelier 40in ssembly Instructions BEFORE INSTLLING FIXTURE, MKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF T THE MIN FUSE BOX / CIRCUIT BREKER UTILITY BOX. Important Safety Instructions:
More informationINSTALLATION INSTRUCTIONS SUPERPLANE 2.5. Suspended. A nd Avenue, Unit 1 Oakland, CA P E W alwusa.
INSTALLATION INSTRUCTIONS SUPERPLANE 2.5 Suspended A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP2.5S - Safety & Warnings! 1. Read all instructions. 2.
More information8200 LED YOKE MOUNT MOUNTING ACCESSORIES
INSTLLTION INSTRUTIONS. e sure the power is off at Yoke ccessories. 2. Install the mounting accessory in the desired location using appropriate fasteners (by others). Mounting accessory sold separately.
More informationInstallation Instructions
01 Inspect : Inspect the box for obvious damage. Make sure the product box was delivered in proper condition and all the fragile labels were honored. If the box looks to be in bad shape; straps are broken,
More informationInstallation Instructions: Eco Linear High Bay
Installation Instructions: Eco Linear High Bay Installation Notes & Precautions: Read all precautions, warnings, instructions contained in this document. These instructions can be used to install Eco Linear
More informationMOONRING 1.5 MOONRING 3
INSTALLATION INSTRUCTIONS MOONRING 1.5 MOONRING 3 MR1.5 & MR3 Suspended, Ceiling LED n A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings!
More informationInstall Guide PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE
PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE This product must be installed in accordance with the applicable code by a person familiar with the construction and operation of the product and the hazards
More informationINSTALLATION INSTRUCTIONS STEP-DOWN TRANSFORMER HOUSING KIT
Rev NSTLLTON NSTRUCTONS STP-DOWN TRNSFORMR HOUSN KT Step-Down Transformer Housing Kit Compatibility: Step-Down Transformer Housing Kit Step-Down Transformer High-ay Conversion Kit HHLPQ32840 HHLSSD1125V
More informationElle Surface Mounting Instructions
Step 1: Preparation, page 2 Warnings CAUTION risk of fire and this product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation
More information2 ½ 4 Deringer 40/50 Maintenance Instructions READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL M-F 8:00 AM 4:30 PM PST
2 ½ 4 eringer 40/50 Maintenance Instructions RE INSTRUTIONS IN FULL EFORE INSTLLTION. QUESTIONS? LL 916-760-4524 M-F 8:00 M 4:30 PM PST t ackflow irect we are committed to making our products as easy to
More informationIntel Server Chassis and Platform Bracket Kit Installation Guide
Intel Server hassis and Platform racket Kit Installation Guide For Intel Server hassis and Platforms SR1400, SR1400JR2, SR1435VP2, SR2400, and SR2400JR2 Order Number: 78599-001 Disclaimer Information in
More informationInstallation for Chevrolet Corvette C7 Stingray PNs 60547* 60548, and 60558
Installation for Chevrolet Corvette C7 Stingray PNs 60547* 60548, and 60558 These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read
More informationSelf-Deploying Rail Kit OEM INSTALLATION MANUAL
Self-Deploying Rail Kit OEM INSTLLTION MNUL TLE OF ONTENTS Introduction 2 Safety Information 2 Resources Required 3 Prior to Installation 3 Installation 3 Doorjamb 3 Setting the Doorjamb 3 inch Latch 4
More informationDC-44 and DC-88 Series Non Spring Return Electronic Actuator Installation Instructions
"" Delta Control Products, Inc. West Rose Garden Lane Phoenix, Z 857 6-78-48 DC-44 and DC-88 Series Non Spring Return Electronic ctuator Installation Instructions Product Description This installation
More information3-Wire Control, 120, 277 Volt T5 Twin Tube Compact Lamps, T4 Quad Tube and T4 Triple Tube
3-Wire Control, 120, 277 Volt, T4 Quad Tube and T4 Triple Tube rev hi-compact-1a 3.7.01 2.38 w (60mm) x 1.50 h (38mm) x 9.50 l (241mm) T4 - One Lamp 3.00 w (76mm) x 1.00 h (25mm) x4.90 l (124mm) T4 - Two
More informationTriple Play Ramp Door OEM INSTALLATION MANUAL
Triple Play Ramp Door OEM INSTLLTION MNUL TLE OF CONTENTS Introduction 2 Safety Information 3 Resources Required 3 Installation 4 Doorjamb 4 Hidden Hinge Installation 7 Door Cable System 8 Electrical Connections
More informationREMOVABLE MOUNT INSTALLATION FOR TRUCK BODIES For truck bodies only, not for trailers. Recommended for use with Dump Beds. See Drawing F.
REMOVBLE MOUNT INSTLLTION FOR TRUCK BODIES For truck bodies only, not for trailers. Recommended for use with Dump Beds. See Drawing 102468F. IMPORTNT. Safe and reliable operation of Donkey mounting kits
More informationLED Garage Light INSTALLATION INSTRUCTIONS. *Model number noted on carton label
LED Garage Light *Model number noted on carton label INSTALLATION INSTRUCTIONS Model Number / Número de Modelo / Numéro des modèle SGLL 24 PIR (24 LED Garage Light) Actual Dimensions 10 W x 3-1/2 H x 24-1/2
More informationSure-Lites. Installation Instructions for the Sure-Lites UX Self Powered Exit Sign with Self Diagnostics. IB505037EN Important Safeguards
049-289 Sure-Lites Installation Instructions for the Sure-Lites UX Self Powered Exit Sign with Self Diagnostics. WARNING Risk of Fire/Electric Shock If not qualified, consult an electrician. WARNING Risk
More informationInstallation Manual F Body (TPI)
Installation Manual 1986-87 F ody (TPI) Engine Compartment Upgrade Kit - 22-229 and 22-229D Congratulations... You have just purchased the highest quality, best performing /C system upgrade ever designed
More informationNANOTUNE. Installation Manual
Installation Manual WARNING: DO NOT ATTEMPT TO INSTALL OR USE THE NANOLUME FIXTURE WITHOUT READING THE INSTALLATION INSTRUCTIONS AND SAFETY LABELS COMPLETELY. Failure to adhere to these instructions could
More informationUltraviolet Fluorescent Lighting Fixtures WF-EM2B, WF-EM4B WF-EM2M, WF-EM4M WF-EM22D, WF-EM4D WF-EM2R, WF-EM4R WF-EMMIM
Operation Manual Ultraviolet Fluorescent Lighting Fixtures WF-EM2B, WF-EM4B WF-EM2M, WF-EM4M WF-EM22D, WF-EM4D WF-EM2R, WF-EM4R WF-EMMIM Table of Contents Specifications 3 General 3 DMX Units 3 Remote
More informationAquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
16 1 AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationCHANDELIER ITEM # MODEL # Français p. 8. Español p. 15 ATTACH YOUR RECEIPT HERE. Serial Number. Purchase Date
ITM #0394659 CHNDLIR MODL #8252-000 Français p. 8 spañol p. 5 TTCH YOUR RCIPT HR Serial Number Purchase Date Questions, problems, missing parts? efore returning to your retailer, call our customer service
More informationELECTRICAL SYSTEM UPGRADE
NEW CONTROLLER & ELECTRICAL SYSTEM UPGRADE FOR DAIRY TECH, INCORPORATED 10, 30 & 60G PASTEURIZERS Parts to Include 2 Wire ties (Nuts) 2 sticky wire mount pads Large Rubber Grommet (for bottom of electric
More informationPantera Electronics LED Taillight Installation Manual
Pantera Electronics LED Taillight Installation Manual (2nd Gen) This LED signal lamp conversion was designed to replace the incandescent lamp 1157 with a Light Emitting Diode Array designed specifically
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationAlbeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series)
GE Lighting Installation Guide Albeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series) Features UL 1598 Suitable for Wet Locations IP66 Rated Ingress Protection BEFORE YOU BEGIN Read these
More informationINSTALLATION GUIDE INSTALLATION GUIDE
INSTALLATION GUIDE INSTALLATION GUIDE Technical Specifications READ AND SAVE THESE INSTRUCTIONS Check the fan label to make sure it is the correct voltage. Operating voltage Diameter Weight Operating frequency
More informationEMERY SKY SUSPENDED LED LUMINAIRE
EMERY SKY SUSPENDED LED LUMINAIRE IP20 DRY LOCATION 120V- 277V AC SAFETY & WARNINGS 1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS 2. Install in accordance with national and local electrical code regulations.
More informationINSTALLATION INSTRUCTIONS 120V DirectAC LED Engine Kit
10W DirectAC Engine TJT120010ACxyyB 15W DirectAC Engine TJT120015ACxyyB INSTALLATION INSTRUCTIONS 120V DirectAC LED Engine Kit TJT120010ACxyyB TJT120015ACxyyB TJT120023ACxyyB TJT120010ASxyyC TJT120010ACxyyC
More informationSOLERA AWNING GAS STRUT REPLACEMENT
Purpose This document provides the steps to replace the awning gas strut assembly. Resources Required 1-2 people, depending on task Pliers Flat head screwdriver 7/16" deep well socket Tin snips Hammer
More informationHPNLS-HO. Installation Manual
Installation Manual WARNING: Do not lift fixture by cables. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/or putting undue pressure
More informationINSTALLATION INSTRUCTIONS MOONRING 1 LP1/MR1
INSTALLATION INSTRUCTIONS MOONRING 1 LP1/MR1 Suspended, Ceiling LED n A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings! 1. Read all instructions.
More informationWiring the FRC Control System
Wiring the FRC Control System This document details the wiring of a basic electronics board for bench-top testing. Some images shown in this section reflect the setup for a Robot Control System using Spark
More informationINSTALLATION GUIDE FOR 30 GALLON SPRAY SYSTEM AERATOR
INSTLLTION GUIDE FOR 30 GLLON SPRY SYSTEM ERTOR ES L. T. RICH PRODUCTS TLE OF CONTENTS 1.0 IMPORTNT INFORMTION... 2 1.1 PURPOSE... 2 1.2 PRODUCT OVERVIEW... 2 1.3 MNUL OVERVIEW... 2 1.4 SFETY... 2 1.5
More informationUSE AND CARE GUIDE 15 INCH WHITE ROUND FLAT PANEL FIXTURE WITH SELECTABLE COLOR TEMPERATURE
74212 USE AND CARE GUIDE 15 INCH WHITE ROUND FLAT PANEL FIXTURE WITH SELECTABLE COLOR TEMPERATURE FEIT ELECTRIC COMPANY PICO RIVERA, CA (800) 543-3348 FAX (562) 908-6360 www.feit.com Table of Contents
More informationType V Accent Light Installation
Packing List: Rheostat Assembly (with cover plate, knob, screws) Accent Light Assembly (with strain relief plate) (2) T4 Halogen Bulbs Bulb Type 35 Watt 120 Volt T4 Halogen Bulb (G6.35 Base) Installation
More informationSconce INSTALLATION INSTRUCTIONS P _2_A 1 of 5
P31421 1 of 5 Thank You For Choosing Kallista We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you install your KALLISTA product. If you encounter
More informationPart No. PAFULAxxx. Figure 2
Part No. PAFULAxxx - Exhaust Vent -To be installed prior to siding- Remove the trim ring and collar from the vent assembly. Place tape or sealant between the Exhaust Vent and house. Align the tube with
More informationSteeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part:
Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part: 555-7316 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5. Vise
More informationGS-IOB-120/240VAC. Input/Output/Bypass Assembly. Installation Instructions. Purpose. Scope. Requirements. Grounding Instructions
GS-IOB-120/240VAC Input/Output/Bypass Assembly Installation Instructions Purpose This document provides information on how to install the Input/Output/Bypass Assembly needed for a 120/240 Vac configuration
More informationINSTALLATION GUIDE INSTALLATION GUIDE
INSTALLATION GUIDE INSTALLATION GUIDE Technical Specifications READ AND SAVE THESE INSTRUCTIONS Check the fan label to make sure it is the correct voltage. Operating voltage Diameter Weight Operating frequency
More information2-row and All-row systems included.
Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown above correspond
More information6 8 Magnum 40(x) Maintenance Instructions
RE INSTRUTIONS IN FULL EFORE INSTLLTION. QUESTIONS? LL 916-760-4524 M-F 8:00 M 4:30 PM PST t ackflow irect we are committed to making our products as easy to install as possible. We design for most contingencies,
More informationMeasurements are expressed in millimeters.
T-Rex user manual Measurements are expressed in millimeters. 1 Lamp access 2 Focus adjustment 3 Mounting bracket 4 Swivel locks 5 Clamp hole 6 Air vent 190 285 7 AC input & main fuse 8 Microphone 490 164
More informationTOYOTA YARIS HATCHBACK INTERIOR LIGHT UPGRADE Preparation
Preparation Part Number PTS21-52062-08 NOTE: Part number of this accessory may not be the same as the part number show Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide
More informationAMP AIR SUSPENSION KITS. HP10193: Ford F-250/350 4WD* Ford F-450* HP10194: Ford F-250/350 2WD* Ford F-450*
MP IR SUSPENSION KITS HP10193: Ford F-250/350 4WD* Ford F-450* HP10194: Ford F-250/350 2WD* Ford F-450* LL KITS FOR TRUCKS INCLUDING IN-ED HITCHES; NOT FOR USE WITH CHSSIS C TRUCKS * See application guide
More informationInstructions for 2-row monitoring only
Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect installation
More informationYARIS 4-DOOR 2007 INTERIOR LIGHT UPGRADE
Document # 3999 4/26/06 4-DOOR 2007 INTERIOR LIGHT UPGRADE Preparation Part Number: 00016-52060 Code: IL1 Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide 3 1 Hardware
More information6 8 Deringer 20/30 Maintenance Instructions READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL M-F 8:00 AM 4:30 PM PST
6 8 eringer 20/30 Maintenance Instructions RE INSTRUTIONS IN FULL EFORE INSTLLTION. QUESTIONS? LL 916-760-4524 M-F 8:00 M 4:30 PM PST t ackflow irect we are committed to making our products as easy to
More informationES50M-65N TROUBLESHOOTING AND REPAIR MANUAL ALL REPAIRS SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN
ES50M-65N TROUBLESHOOTING AND REPAIR MANUAL ALL REPAIRS SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN The ES50M-65N is a field repairable switch. Warranty covers defective parts only. Do not return the
More informationC.fm Page 1 Thursday, February 21, :28 AM Raptor user manual
Raptor user manual 1 mounting bracket 2 swivel lock 3 clamp hole 4 lamp access screws 5 air vents 6 AC input & main fuse 7 cooling fan Thank you for selecting the Martin Raptor. This Martin lighting fixture
More informationIMPORTANT SAFEGUARDS
INSTRUCTION MANUAL NON-INTERRUPTIBLE AC INVERTER SYSTEM MODEL EAC FTM 350 FOR EMERGENCY LIGHTING POWER IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed,
More informationEMERALD CUBICLE COLLECTION. Installation Guide
MRL UIL OLLTION Installation Guide Panel to Panel onnector VIW VIO for Panel to Panel onnector: http://www.youtube.com/watch?feature=player_embedded&v=5s4zwoa9u7c#at=43 This onnects 2 Panels Together Side
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
1 AQUALUMIN III NICHELESS POOL LIGHT INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationPantera Electronics LED Taillight Conversion Installation Manual
Pantera Electronics LED Taillight Conversion Installation Manual This LED signal lamp conversion was designed to replace the incandescent lamp 1157 with a Light Emitting Diode Array designed specifically
More informationSivoia QED roller 20TM. Installation Instructions
Sivoia QED roller 20TM Installation Instructions Sivoia QED roller 20TM Installation instructions Tools required: Tape Measure Wire Cutter/Stripper Pliers #2 Phillips Screwdriver /4 in Hex-Head Driver
More informationUse and Care Guide. Part # UC SV-D Model # UC SV-d UC SV-d
Part # UC-12-5-930-SV-D Model # 53502111 UC-18-9-930-SV-d 53503111 UC-24-12-930-SV-d 53504111 Use and Care Guide BEM DJUSTBLE LED UNDER CBINET LIGHT WITH MGN MOUNT INSTLLTION OPTION Questions, problems,
More informationInstallation Manual Chevrolet G Body
Installation Manual 78-88 Chevrolet G ody Engine Compartment Upgrade Kit - 122-2004 Congratulations... You have just purchased the highest quality, best performing /C system upgrade ever designed for your
More informationK B J K A C H D E I F. Single and Bi-Parting Electric Sliding Doors with Automatic Operator (ICC-5) Parts List. R-PLUS Cold Storage Doors
Single and Bi-Parting Electric Sliding Doors with Automatic Operator (ICC-) Parts List K B J K A C H G Release Date: -0 D E R-PLUS Cold Storage Doors NE 9th Portland, Oregon 90 Toll Free () 0-99 Fax (0)
More informationA CHANNEL. Installation Instructions for Tie Stix Wall 2-Light. Section One: 4SQ Version
0 Edge Lighting. All Rights Reserved. W. Fullerton Ave Chicago, IL 0 Tel: -0- Fax: -- www.edgelighting.com info@edgelighting.com Installation Instructions for Tie Stix Wall -Light IMPORTANT INFORMATION
More informationROPE LIGHT ITEM # MODEL #UCL48L. Français p. 8. Español p. 15 ATTACH YOUR RECEIPT HERE. Purchase Date
ITEM #0879887 ROPE LIGHT MODEL #UCL48L Français p. 8 Español p. 15 TTCH YOUR RECEIPT HERE E237798 Purchase Date Questions, problems, missing parts? efore returning to your retailer, call our customer service
More informationSPORTSTER SADDLEBAG KIT. i i02212
General These saddlebags are designed to fit 99 and later Sportster Model Motorcycles, except XL00 Sport models with gas reservoir shock absorbers and 88R models. See the Service Parts pages for a list
More informationINSTRUCTIONS. Power Panel. Installation Instructions
Overview LuXout Shade 18 Output - For use with LuXout Shades NOTICE: This power supply is built-in fan on/off control circuit. Fan automatically works according to working temperature. SHOCK HAZARD Risk
More informationCarousel Unit User Manual Replacing the Check Stand Motor
Carousel Unit User Manual Replacing the Check Stand Motor 02/01/2017 1 Table of Contents Tools:... 3 Turn Off Power to the Unit:... 4 Remove Power Switch... 5 Remove Electric Eyes:... 6 Remove POS (Point-Of-Sale)
More informationCHEMICAL MIXING SYSTEM OPERATING AND INSTALLATION INSTRUCTIONS
Chemical Mixing System Operating and Installation Instructions for Focus II Mid-Size Walk-Behind Kit #11363A CHEMICAL MIXING SYSTEM OPERATING AND INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Phillips Screwdriver
More informationImportant! It is essential that you read the instructions in this manual before assembling, operating, and maintaining the product.
Important! This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
More informationDo not print this page
Do not print this page 2006. Nautilus, Inc. All Rights Reserved. Schwinn is a registered trademark. Nautilus, Inc., World Headquarters, 16400 SE Nautilus Dr., Vancouver, WA 98683 Recumbent Assembly guide
More informationGS-IOB-230VAC. Input/Output/Bypass Assembly. Installation Instructions. Purpose. Scope. Requirements. Grounding Instructions
GS-IOB-230VAC Input/Output/Bypass Assembly Installation Instructions Purpose This document provides information on how to install the Input/Output/Bypass Assembly needed for a single-phase configuration
More information9.2, 9.2s, 9.20, 9.20s Treadmill
9.2, 9.2s, 9.20, 9.20s Treadmill Warning: This service manual is for use by Precor trained service providers only. If you are not a Precor Trained Servicer, you must not attempt to service any Precor Product;
More informationBase Power Infeed Installation for Training Tables with Modular Table Power System
Base Power Infeed Installation for Training Tables with Modular Table Power System Topic Table of Contents General Safety Warnings Base Power Infeed Usage Electrical Circuits Base Power Infeed - 0 Amp
More informationStrip Fixture URS Light Bar Retrofit Installation Instructions Revised:
Strip Fixture URS Light Bar Retrofit Installation Instructions Revised: 20180126 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency
More informationDOOR KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
DOOR KIT P/N 2882561, 2882562 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More informationInstruction Sheet. Subject: Installations Instructions. Air Compressor Kits. Importan
MULTIPLEX 2100 FUTURE, SELLERSBURG, IN 47172 800-367-4233 WWW.MANITOWOCBEVERAGE.COM/US Instruction Sheet Subject: Installations Instructions Importan Read the following warnings before beginning an installation.
More informationSivoia QED R Installation Instructions Please Leave for Occupant
Sivoia QED R Installation Instructions Please Leave for Occupant SV-100SF-230-ST 24 V~ Safety Isolating Transformer Input: 230-240 V~ 50/60 Hz Output: 24 V~ 60Hz 3,15 A Please read before installing. Description
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationInstallation Manual Chevrolet G Body
Installation Manual 78-88 Chevrolet G ody Compressor Upgrade Kit - 123-2004 Congratulations... You have just purchased the highest quality, best performing /C system upgrade ever designed for your Classic
More informationHÖRMANN DSA 100 DSA 100 L DSA 200 DSA 200L. page 1
HÖRMNN Spindle drive operator for hinged gates DS 100 DS 100 L DS 200 DS 200L Installation Instructions page 1 1 Overview of spindle drive operator for hinged gates E F a e f C b c D d g Table 1: Drive
More informationIvalo Finiré 3 LED Recessed Lighting Installation Instructions
IMPORTANT INFORMATION Please Read Before Installing 367-2578e 1 09.20.16 Important Notes IC fixtures must be used for installations containing insulating materials and must be mounted away from heat producing
More informationINSTALLATION INSTRUCTIONS FOR PART B. APPLICATIONS MAZDA up
INSTLLTION INSTRUCTIONS FOR PRT 99-75 PPLICTIONS MZD 00-up 99-75 U.S. Patent # D69,90 KIT FETURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Radio Provision Stacked
More informationLED IMPORTANT SAFETY INSTRUCTIONS
U02301 Rev. B Page 1 of 8 U02301 Rev. B Page 2 of 8 IBG LED HIGHBAY INSTALLATION INSTRUCTIONS WARNING: Please read all important safety instructions prior to installation of this product. A) Identification
More informationSway Command Tow Control System
Sway Command Tow Control System (For Travel Trailer) OEM INSTLLTION MNUL TBLE OF CONTENTS Introduction 2 Causes of Sway 2 Preparation (Non-Prepped Trailer) 3 Resources Required 3 Components Required 3
More informationILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT
082114EC ILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT Beghelli Canada 3900 14th Avenue Markham, Ontario L3R 4R3 Canada P: (905) 948-9500 F: (905) 948-8673 www.beghellicanada.com Beghelli
More informationINSTALLATION GUIDE INSTALLATION GUIDE
INSTALLATION GUIDE INSTALLATION GUIDE Technical Specifications READ AND SAVE THESE INSTRUCTIONS Check the fan label to make sure it is the correct voltage. Operating voltage Diameter Weight Operating frequency
More informationL ale. 4' 8" Fluorescent Two Lamp Decorative Pendant 56 in long, 42 W, Compact Fluorescent, Direct/Indirect Cable Suspension Models APPLICATIONS
11 3 4 in (98 mm) Bottom View (Canopy) H A B C 367-5c 1 07.13.16 18 in 60 in (457 mm 154mm) 1/4 in (6 mm) 4 3 8 in (111 mm) 5 1 in (140 mm) A - Aluminium coverplate B -Aluminium canopy C - i-wire, power,
More informationInstallation Instructions MX LED Enhanced Color Adjustable
Installation Instructions 1 of 5 MX Enhanced Color Adjustable Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. will fail if not installed properly.
More informationNICHE-HV. Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES.
Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/ or putting undue pressure
More informationInstallation Guide. Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) Section 1.0: Mounting the M-Series Arm Parts Reference...
Installation Guide Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) The purpose of this guide is to describe installation of the MP90 M-Series Wall Mount Kit. Table of Contents Section 1.0: Mounting
More informationNANO MIX. Installation Manual
Installation Manual WARNING: DO NOT ATTEMPT TO INSTALL OR USE THE NANOLUME FIXTURE WITHOUT READING THE INSTALLATION INSTRUCTIONS AND SAFETY LABELS COMPLETELY. Failure to adhere to these instructions could
More informationInstallation Instructions MX LED Downlight Remodel
1 of 5 Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. Luminaire will fail if not installed properly. Follow installation instructions. Risk
More informationP/N Wheeler. user manual
P/N 35000068 Wheeler user manual 1998, 1999 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from
More informationSivoia QS Wireless Drapery Lite System
Sivoia QS Wireless Drapery Lite System English Installation Guide Please Read Before Installing Important Notes - Please Read Before Installing A. Lutron systems are intended for use with only Lutron hardware
More informationInstallation Instructions: Eco SpunBay LED High Bays
Installation Instructions: Eco SpunBay LED High Bays Installation Notes & Precautions: Read all precautions, warnings, instructions contained in this document. These instructions can be used to install
More information