Install Guide PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE
|
|
- Alan Bryan
- 5 years ago
- Views:
Transcription
1 PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE This product must be installed in accordance with the applicable code by a person familiar with the construction and operation of the product and the hazards involved. Read all of these instructions before WARNING: Disconnect power prior to servicing or 1 3 1/4-20 ROD 3/8" ~ 1/2" BELOW CEILING 3 ½ (Typ.) Install an Iberville 1 ½ deep octagon box (part # CI /2) or equivalent. Center octagon box in position for best fixture position. CABLE COUPLER #2 Positioning of Cable Coupler #2 will be determined by the length of the PMX fixture being installed. 2 1/4-20 rod must be secured or anchored in ceiling system. (rod or anchoring to be supplied by others). Proper installation of the rod length should protrude through the ceiling approximately 3/8 to ½ Once installed and secured, cable coupler #2 can now be screwed into the rod. WALL PLATE 1/4-20 STUD INTEGRATED INTO POWER CANOPY 4 CABLE STAY SP1 POWER CANOPY CABLE COUPLER #1 3/64" AIRCRAFT CABLE POWER CORD BUSHING END GLIDERS TRANSVERSE CABLE THUMB SCREW Install wall plate, make electrical connection from power cord supplied with PMX fixture. Install power cord bushing. Mount power canopy with 4 set CSK screws provided. Install cable coupler #1 into power canopy stud. To ensure the PMX fixture is horizontally balanced, adjust transverse cable by loosen transverse cable thumb screw. Addition cable available at the end gliders. Adjust power cord tension by loosen thumb screw of cable stable. PMX-Pendant-Matrix-Install Subject to change without notice REV /5
2 PMX SERIES PENDANT MOUNTED MATRIX SP2 STYLE This product must be installed in accordance with the applicable code by a person familiar with the construction and operation of the product and the hazards involved. Read all of these instructions before WARNING: Disconnect power prior to servicing or ½ (Typ.) Install an Iberville 1 ½ deep octagon box (part # CI /2) or equivalent. Center octagon box in position for best fixture position. END GLIDERS CABLE STAY To adjust length of aircraft cable and horizontal balance of fixture, adjust all four end gliders individually. additional cable available at the end glider. 2 Adjust power cord tension by loosen thumb screw of cable stable. WALL PLATE SP2 POWER CANOPY 3/64" AIRCRAFT CABLE POWER CORD BUSHING Install wall plate, make electrical connection from power cord supplied with PMX fixture. Install power cord bushing. Mount power canopy with 4 set CSK screws provided. PMX-Pendant-Matrix-Install Subject to change without notice REV /5
3 CDMR 111 AR 111 PAR 36 PMX LARGE SERIES Glass Lens Option Twist lamp into GX 8.5 socket accordingly. PAR 30 CMH Attach AR111 lamp into socket provided. PAR 30 Halogen Attach PAR36 lamp into socket provided. T4 G8.5 CMH To Install an optional glass lens, twist counterclockwise to release front ring, turn ring until tabs line up & ring drops out. Install glass lens into face ring, use snap ring to hold glass in position. (Glass Lens & Snap ring ordered separately) Twist lamp into medium base socket. Place lamp between clips on adaptor ring. Twist lamp into medium base socket. Place lamp between clips on adaptor ring. Insert Bi-pin T4 lamp into socket. PMX-Pendant-Matrix-Install Subject to change without notice REV /5
4 PMX SMALL SERIES MR16 GX10 CMH AR70 Glass Lens Option Push MR16 lamp into GU 5.3 (MR16 ) Socket accordingly. Place MR16 lamp into adapter ring PAR20 CMH Twist GX10 MR16 CMH lamp into GX10 Socket accordingly. Line up tabs on front ring to base ring, PAR 20 Twist AR70 Lamp into DC Bayonet base Socket provided. Line up tabs on front ring to base ring XIC LED To Install an optional glass lens, twist counterclockwise to release front ring, turn ring until tabs line up & ring drops out. Install glass lens into face ring, use snap ring to hold glass in position. (Glass Lens & Snap ring ordered separately) Twist lamp into medium base pulse rated Socket. Line up tabs on front ring to base ring, turn clockwise to secure into place. Twist lamp into medium base Socket. Release lamp holder from assembly, remove green protective film over adapter PMX-Pendant-Matrix-Install Subject to change without notice REV /5
5 XIC STANDARD (ELV) DIMMING INSTRUCTION WARNING: ENSURE FIXTURE IS SWITCHED OFF BEFORE CONNECTING LED PRODUCT. FAILURE TO DO SO WILL CAUSE IMMEDIATE LED FAILURE Junction box Wiring Internal wiring within Housing (cannot be changed) CONNECT TO 120VAC OR 277V, 50/60Hz INPUT ELECTRONIC LOW VOLTAGE DIMMER (ELV) OPTIONAL NEUTRAL (WHITE) HOT LED DRIVER ELV DIMMING LED- LED- LED+ (RED) LED+ (RED) MATING CONNECTORS FOR LED XIC LED MODULE PMX-Pendant-Matrix-Install Subject to change without notice REV /5
Potenza Commercial Pendant Compact Fluorescent, Incandescent, HID Medium, Large
PRODUCT SPECIFICATIONS PENDANT: Extruded aluminum body with silver powder coat finish. Clear prismatic acrylic diffuser dome provides soft self-illumination. MOUNTING: 4 solid square fixture hanger attached
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS This document explains mounting for pendant, recessed, and wall PENDANT - STEP ONE INSTALL MOUNTING POINTS Non-power feed mounting points may be positioned 1 to 12 or 12 to 18
More informationWhen using electrical equipment, basic safety precautions should always be followed including the following:
INDUSTRIAL INSTALLATION INSTRUCTIONS Illumina BS100LED2FT-PLUS EACH MODEL NUMBER CONSISTS OF THE FOLLOWING: SERIES / LENGTH / OPERATION / LUMENS / COLOUR TEMP. / INPUT SERIES: LENGTH: OPERATION: BS100LED2PLUS
More informationILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT
082114EC ILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT Beghelli Canada 3900 14th Avenue Markham, Ontario L3R 4R3 Canada P: (905) 948-9500 F: (905) 948-8673 www.beghellicanada.com Beghelli
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More information4" (10cm) 15H1-250W 18F1/F1E - 62W K 18H1-300W. Standard 120V (leave blank) 2 230V 50Hz 3 277V 60Hz. 14" (36cm)
116 Simple elegant designs in the Edge Lighting ceiling collection easily adapt to any decor. The fixtures with indoor/outdoor and ceiling/wall options, provide multitask lighting for various applications.
More information1718 W. Fullerton Ave Chicago, IL Tel: Fax:
07 Edge Lighting. All Rights Reserved. Installation Instructions for Pix Stick Tie Stix Suspension -Light, -Light, -Light and -Light with Power IMPORTANT INFORMATION - This product is suitable for indoor
More informationLumination TM LED Luminaires Suspended LED Fixture (Series EP14)
GE Lighting Solutions Installation Guide Lumination TM LED Luminaires Suspended LED Fixture (Series EP14) Features Long life (50,000 hour rated life) 5 year warranty IP30 Dry location rated BEFORE YOU
More informationNT-300 Series Single Circuit Track System & Accessories
NT-300 Series Single Circuit Track System & Accessories Type Project Catalog No. Lamp/Wattage PRODUCT DESCRIPTION Low profile, extruded aluminum track with 20-Amp rated flat, solid integral copper conductors.
More informationLumeLEX 2084 SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2084 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationFINA SUSPENDED INSTALLATION INSTRUCTIONS
FINA SUSPENDED INSTALLATION INSTRUCTIONS 3 AC Cable Mounting (AC3) Installation... 2-4 AC Cable to Hub Mounting (AH4) Installation... 5-7 Pendant Pipe Mounting Installation... 8-9 Canopy Detail... 10-11
More informationCustomer service: or Upper mounting ring. Canopy
Components included: Upper mounting ring Canopy Fixture base Fluorescent - 2 x 42 W 4-pin compact fluorescent lamps required (not included). Lutron recommends GE, Sylvania, or Philips lamps that are certified
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationOperation Manual Image
Operation Manual Image 82, 42, 22 4/14/03 Image 82 8 x 4ft lamps Manual on/off switching control Switches 2 lamps at a time Image 42 4 x 4ft lamps Manual on/off switching control Switches 2 lamps at a
More informationC.fm Page 1 Thursday, February 21, :28 AM Raptor user manual
Raptor user manual 1 mounting bracket 2 swivel lock 3 clamp hole 4 lamp access screws 5 air vents 6 AC input & main fuse 7 cooling fan Thank you for selecting the Martin Raptor. This Martin lighting fixture
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationRound or Square Type Non-IC Adjustable Housing with Toroidal Transformer for Flangeless Trims E3_L_-HANM_ 1.7
Installation Instructions for 90EHMH-ANIC Round or Square Type Non-IC Adjustable Housing with Toroidal Transformer for Flangeless Trims E_L_-HANM_. HALOGEN MR - ROUND/SQUARE FLANGELESS GENERAL PRODUCT
More information130 130 Simple elegant designs in the Edge Lighting ceiling collection easily adapt to any decor. The fixtures with indoor/outdoor and ceiling/wall options, provide multitask lighting for various applications.
More informationES44-LED SERIES DIRECT OR INDIRECT HIGH EFFICIENCY LED - RECESSED, SURFACE, WALL OR SUSPENDED
ES44-LED SERIES DIRECT OR INDIRECT HIGH EFFICIENCY LED - RECESSED, SURFACE, WALL OR SUSPENDED PERFORMANCE CHARACTERISTICS Optical Efficiency: 90.5% max Lumens per watt: 180 max Lumen output: 2200Lm/ft
More information1Unpack fixture. Suspensions/canopies are ordered and
DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at 1-800-448-4131 questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions 2Determine
More informationAssembly instruction. Pendant Light Toccata GENERAL REMARKS ON SAFETY: Technical data: BOM
GENERAL REMARKS ON SAFETY: Read all of these instructions before installing fixtures. Keep all of the instructions for future reference. Turn off power before installing fixture. Installation is to be
More informationFinish: Stainless Steel
miniport LED Indoor/Outdoor : Miniport LED is slim and can be recessed into a wall or floor using a MiniPort junction box, which mounts to an octagon box or outdoor, wet-location electrical box. The fixture,
More informationInstallation Guide DO NOT CUT WIRES
Installation Guide LED INFO & WARNINGS Please read and comprehend the entire manual before attempting to assemble, operate, or install the product. Make sure that you have all necessary parts by checking
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS IMPORTANT Before opening your Lights.com fixture, please make sure that you carefully read through these instruction sheets. Consider having your fixture installed by a qualified
More informationD.fm Page 1 Wednesday, March 5, :21 PM Raptor user manual
Raptor user manual 1 mounting bracket 2 swivel lock 3 clamp hole 4 lamp access screws 5 air vents 2001-2002 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced,
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationLamp: 7WDC 27K WDC 30K DC 27K DC 30K
Made in the USA 12"- 144" 1.025" (2.6cm) (0.76cm) Cirrus Channel Wall Grazer features a lens that provides dramatic accent lighting to highlight textured surfaces. At 7 or 10.5 watts per foot, the 24 volt
More informationA CHANNEL. Installation Instructions for Tie Stix Wall 2-Light. Section One: 4SQ Version
0 Edge Lighting. All Rights Reserved. W. Fullerton Ave Chicago, IL 0 Tel: -0- Fax: -- www.edgelighting.com info@edgelighting.com Installation Instructions for Tie Stix Wall -Light IMPORTANT INFORMATION
More informationHBDBM High Bay Series
HBDBM High Bay Series INSTALLATION INSTRUCTIONS The High Bay Luminaire is ideal for installations with mounting heights over 25 feet. The fixture can be mounted with a hook or pendant with flexible adjustments
More informationALU-29CF Portable Light NSN:
ALU-29CF Portable Light NSN: 6520-01-446-4170 COMMAND l AIR OPERATION / MAINTENANCE MANUAL & PARTS LIST TABLE OF CONTENTS Introduction................................................................3 Purpose.............................................................3
More informationHigh Bay Luminaire Series
High Bay Luminaire Series INSTALLATION INSTRUCTIONS The High Bay Luminaire is ideal for installations with mounting heights over 25 feet. The fixture can be mounted with a hook or pendant with flexible
More informationINSTRUCTION MANUAL SINKER. By HAY
INSTRUCTION MANUAL SINKER By HAY INTRODUCTION An elemental looking light available as either a small or large pendant. The fabric cord comes with a magnetic moulded ceiling cap in a textured finish. The
More informationC35. Assembly Instructions. Mobius Floor Lamp & C Page 1 of 7. Prepare Base (Figures 1& 2)
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationSection One: Install the Constant Current DMX Driver
Intelligent LED Driver/Controller Output 060VDC, 0050mA, 0W SELV equivalent : 0% typ. in in out out Group Group LEDcode in in out out Group Group LEDcode 06 Edge Lighting. All Rights Reserved. Installation
More informationZIP LIGHT LED LUMINAIRE
LED LUMINAIRE INSTALLATION MANUAL Note: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the Canadian Electrical Code (CE) and for the United States follow
More informationTAGORA design S. & R. CORNELISSEN
TAGORA design S. & R. CORNELISSEN HOTEL BELVOIR, RÜSCHLIKON (CH), MOKARCHITECTURE, ZÜRICH TAGORA CEILING design S. & R. CORNELISSEN A SERIES OF CEILING MOUNTED FIXTURES AVAILABLE IN THREE DIAMETER OPTIONS,
More informationOperation Manual. Flathead 80 System
Operation Manual Flathead 80 System Part No. 3100006 Rev B 01-07-2008 CFX-4808 Flathead 80 Fixture MTP-K81 Mounting plate X16-25 4Bank Extension, 25ft (x2) X16-12 4Bank Extension, 12ft (x2) BAL-410-S120
More informationC35 Mobius Floor Lamp & C Page 1 of 7
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationLinear Fluorescent Lampholders. Compact Fluorescent Lampholders (CFL s)
CATALOG LINE CARD Linear Fluorescent Lampholders Miniature Bi-Pin Low and tall profile, snap-in/slide-on for T-5, shunted and non-shunted T-8 to T-5 adapter Butt-on for T-5 Medium Bi-Pin Internal shunt
More informationALKCO where quality comes to light
ALKCO where quality comes to light A JJI Lighting Group Company Spazio A spotlight on style. Spazio fixtures 4.75 4 precisely focus the lighting where your design requires. The elegant handle 4.5 makes
More informationInstallation Instructions
LENNON 3 LIGHT PENDANT SKU# 039010, 039013 Rated Voltage 220-240V~ 50Hz Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions
More informationInstallation Instructions
QUINN 6 LIGHT PENDANT SKU# 039019, 039020 Rated Voltage 220-240V~ 50Hz Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions
More information1718 W. Fullerton Ave Chicago, IL Tel: Fax:
206 Edge Lighting. All Rights Reserved. Installation Instructions for Nova Power Suspension Up/Down - Center Feed Glide Up/Down - Center Feed IMPORTANT INFORMATION - This product is suitable for indoor
More informationTrack Accessories. Single Circuit Track. L Connector T Connector X Connector. Mini Connector Floating Canopy End Feed Kit.
Single Circuit Single Circuit Track Live End Connector Flexible Connector Straight Connector Track supplied with dead end and mounting hardware Live end connector used for direct wiring Flexible connector
More informationOperation Manual Mega. 4Bank, Double & Single
Operation Manual Mega 4Bank, Double & Single Part No. 3100012 Rev C 04-20-2009 4Bank Double Single Each System consists of: 1 Mega Fixture 1 Mounting Plate 1 Extension Cable 1 Electronic Ballast 2 (2X)
More informationMONORAIL KITS INSTALLATION INSTRUCTIONS PENDANTS
MONORAIL KITS PENDANTS JESCO Lighting Group is a UL and ETL listed company Copyright 2011 JESCO Lighting Group. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS Be sure to read and unsderstand the following
More informationOperation Manual. 12V Single Kit
Operation Manual 12V Single Kit Part No. 3100034 Rev C 01-07-2008 KIT-140X 12V Single Kit, 12VDC Kit Contents: 2 12V Single Ballast xlr 2 15 12V Single Fixture 2 Extension, 25ft 1 Car Adapter xlr 1 Alligator
More informationEMERY SKY SUSPENDED LED LUMINAIRE
EMERY SKY SUSPENDED LED LUMINAIRE IP20 DRY LOCATION 120V- 277V AC SAFETY & WARNINGS 1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS 2. Install in accordance with national and local electrical code regulations.
More informationLED SMD CANOPY FLAT FIXTURE
ASD LED Canopy Lights are designed to withstand the elements while producing a lot of light. Our low profile canopy has an acrylic lens which is UV resistant and vandal-resistant. This is an ideal replacement
More informationD3 INSTALLATION GUIDE
D3 INSTALLATION GUIDE Supported Models D3-FXRD D3-FXSQ D3-ADRD D3-ADSQ D3-WWRD D3-WWSQ D3 INSTALLATION GUIDE 770-000028-0X r09 PAGE 1 ! WARNING! Shock Hazard. May result in serious injury or death. Turn
More informationMeasurements are expressed in millimeters.
T-Rex user manual Measurements are expressed in millimeters. 1 Lamp access 2 Focus adjustment 3 Mounting bracket 4 Swivel locks 5 Clamp hole 6 Air vent 190 285 7 AC input & main fuse 8 Microphone 490 164
More informationELS Electronic Lighting System
ELS Electronic Lighting System T-8 Lamp Replacement November, 2012 99-20374-I001 I. T-8 Lamp Replacement Instructions Center Mullion Fixtures 1. Turn light power off before start of lamp replacement. 2.
More informationMEDIA LED. Pendant Standard Mount Installation ou de montage WARNING:
MEDIA LED Pendant Standard Mount WARNING: Disconnect main power at the source prior to installation! Thread gripper base onto 1 /4 20 stud, or with #8 screw. Depress gripper nozzle to insert aircraft cable.
More informationP/N Wheeler. user manual
P/N 35000068 Wheeler user manual 1998, 1999 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from
More informationtable of contents Lampholders for Innovative Light Sources SECTION C CS ECTION
table of contents Lampholders for Innovative Light Sources Advances in lighting technology provide lamps with exceptional brightness, color rendition, energy efficiency and compact size. Leviton meets
More informationHP-2 / HP-6 Direct Installation Instructions Overview
Overview Helpful Video 0-10V Dimming Step 1 Mounting & Suspension Page 2 Step 2 Identification & Preparation Page 3 Step 3 Mounting to Structure Page 4 NOTE Step 4 Page 5 This installation requires proper
More informationFluorescent Ring Light with Dimmer INSTRUCTIONS
Fluorescent Ring Light with Dimmer INSTRUCTIONS Introduction Thank you for choosing Impact. The Impact Fluorescent Ring Light with Dimmer is a continuous light for photography and video. It casts a soft,
More informationWARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS
WARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS DO NOT solder connectors as this will prohibit the adapters circuit switch to move freely from circuit to circuit. Nordic Aluminium track adapters and accessories
More informationOutdoor Installation Using an Electronic LED Power Supply (TE-60L-12)
0 Edge Lighting. All Rights Reserved. 78 W. Fullerton Ave Chicago, IL 606 Tel: 77-770-9 Fax: 77-9-6 www.edgelighting.com info@edgelighting.com Installation Instructions for Port Round & Square LED PORT-RD-ST-SA
More informationCIRRUS SUSPENSION WALL WASH WITH REMOTE POWER, END FEED
Adjustable Max. 5 ft. Description Cirrus Suspension Wall Wash with Remote 24VDC power supply (sold separately) is a linear LED fixture that offers a wall wash lens for a smooth and uniform beam spread.
More informationHeads. track. track heads. R20 Step Cylinder. R30 Step Cylinder. R20 Soft Square. R30 Soft Square. TH204 White TH205 Black TH303 Brushed Nickel
track Heads track heads R30 Step Cylinder TH206 White TH207 Black TH304 Brushed Nickel (1) R30/PAR30 75W max. (Long Neck) Dimensions: Height 6 1 2, Width 4 1 2, Extension 8 1 2 R20 Step Cylinder TH204
More informationINSTALLATION INSTRUCTION Oculux 3.5" Architectural Downlight R3CRN-11, R3CSN-11
. INSTALLATION INSTRUCTION SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified
More informationAsymmetrical Installation Instructions. Components: i2cove Asymmetrical LED Light Fixtures. 12 [305mm] [918mm] 48.
support@i2systems.com www.i2systems.com Electrical Specifications PARAMETER Input Power VALUE 8 Watts* / Ft Input Voltage 120-277V AC, 50/60 Hz Max. Fixture Run Length LED Color (CCT) 8 Watts: 120VAC:
More informationModel Dimming Output CRI C.C.T. Reflector Optical Accessories Shell Color Suspension Options AP
PROJECT Job Notes Type Part # SPECIFICATIONS Source Cree CXB Integrated LED Array, up to 161 lm/w C.C.T. 2700K, 3000K, 3500K, 4000K or 5000K Color Consistency 3x3 SDCM (MacAdam) CRI (Ra) 80 or 92 Driver
More informationNOVA suspension up and down, end feed with remote power supply
Shown without Louver Shown with White Louver Description Nova Suspension Up/Down is a linear LED lighting 2 circuit system that features both direct and indirect light. This contemporary system allows
More informationULTRA PERFORMANCE LED TUBE INSTALLATION INSTRUCTIONS
Ultra Performance LED Tube Installation Instructions Page 1 of 7 ULTRA PERFORMANCE LED TUBE INSTALLATION INSTRUCTIONS These instructions do not purport to cover all details or variations in components
More informationPRODUCT MANUAL Gecko Wireless One Zone LED Dimmer and Receiver
Product Description The Gecko Wireless One Zone Wall LED Dimmer has been designed to bring light control easily. No wires or switch box locations are needed, just stick or mount the Gecko to any flat location
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More information0.25" (0.64cm) Grip Jack Connector 2WDC WDC Lumen values are based on the 3000K LED test.
0.25" (0.64cm) Grip Jack Connector Field Adjustable with Grip Jack Connector Adjustable Max. 5 ft. Description: Cirrus Channel Suspension D1 features a direct flat lens with 100 degree beam spread. At
More informationCR Series and DR Series LED Downlights EASY TO INSTALL WITH UNPRECEDENTED PAYBACK
CR Series and DR Series LED Downlights EASY TO INSTALL WITH UNPRECEDENTED PAYBACK The Quality You Demand with the Savings You Deserve. Inspired by Your Needs SOLUTIONS THAT DELIVER Cree CR Series and DR
More informationCharcoal Filter Installation NOTE: The charcoal filters are preinstalled if you purchased the range hood with re-circulating kit from us. 1. Remove st
Venting Methods This range hood is factory set for venting through the roof or wall. For non-vented (re-circulating) installations, see Ductless Conversion on Page 7. Vent work can terminate either through
More informationVISA Bottom Detail (cutouts backed by white acrylic) Confetti (CNF) Solid (SLD) Slots (SLT) Windows (WIN)
TM Bottom Detail (cutouts backed by white acrylic) Confetti () Solid () Slots () Windows () 254 FEATURES 5 year product warranty Configurable segments available to create unique shapes for general illumination
More informationDISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.
308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing
More informationAlbeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series)
GE Lighting Installation Guide Albeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series) Features UL 1598 Suitable for Wet Locations IP66 Rated Ingress Protection BEFORE YOU BEGIN Read these
More informationOperation Manual. 4Bank, Double & Single
Operation Manual 4Bank, Double & Single Part No. 3100071 Rev C 08-29-2017 Systems 4Bank Double Single Each System consists of: 1 Fixture 1 Mounting Plate 1 Extension Cable 1 Ballast True Match Lamps 488-K32-S/6P
More informationLED CANOPY with j-box
ASD Garage Canopy Luminaire with junction box provides a slim, low profile solution for easy mounting. Built with rugged cast aluminum, this luminaire is available with surface or pendant mount. J-Box
More informationHPNLS-HO. Installation Manual
Installation Manual WARNING: Do not lift fixture by cables. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/or putting undue pressure
More informationInstallation Instruction
T F W 604.549.9379 604.549.9555 fluxwerx.com Installation Instruction DRIVER ENCLOSURE Ceiling Type Version Grid Battery Pack GRID MOUNT INSTALL OPTIONS OPTION 1: Standard Vertical Grid drivers can be
More information12 INCH WAREHOUSE BARN PENDANT LIGHT
12 INCH WAREHOUSE BARN PENDANT LIGHT OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationProduct Selection Card
Summer 2018 Lamps -- Gen 2 11W 1,800 15W 2,200 3Ft Gen 2 11W 1,400 8W 1,200 Bi-pin G13 22in 6 15W 2,200 22in 1-5/8 12W 1,700 17W 2,100 Lamps -- Lunera LED Gen DLC Status UL Type Wattage Max Lumens Color
More informationINSTALLATION INSTRUCTIONS SUPERPLANE 2.5. Suspended. A nd Avenue, Unit 1 Oakland, CA P E W alwusa.
INSTALLATION INSTRUCTIONS SUPERPLANE 2.5 Suspended A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP2.5S - Safety & Warnings! 1. Read all instructions. 2.
More informationRemote Power Supplies * & Dimmers (Sold Separately): Electronic Low Voltage Dimming (ELV) 0-10 Volt Dimming (0-10V) Lutron
0.25" (0.64cm) Grip Jack Connector Field Adjustable with Grip Jack Connector Adjustable Max. 5 ft. 0.9" 0.35" (0.9cm) 0.9" 0.38" (0.95cm) Description: Cirrus Channel Suspension Wall Wash uses a wall wash
More informationZynn Lines - Pendant. AIP in DESCRIPTION FEATURES & BENEFITS SPECIFICATIONS PROJECT DETAILS JOB NAME: TYPE: NOTES:
Zynn Lines - Pendant AIP12116 49 in JOB NAME: TYPE: NOTES: PROJECT DETAILS DESCRIPTION With a cross-section of just 1.25", Zynn Lines suspends slim lines of light in contemporary spaces. Its seamless housing,
More informationPortable Lighting Equipment Operating Instructions Table of Contents
Portable Lighting Equipment Operating Instructions Table of Generac Magnum Ingersoll Rand TEREX AMIDA TEREX GENIE Model: MLT3060 Model: LIGHTSOURCE Model: Amida AL4000 series Model: TML4000N Generac Magnum
More informationSilvus TM 30 Exterior
Components included Sconce and Mounting Plate with Locking Plate attached. Three wire connectors and one washer 30 fixture 60 fixture Marked Marked -to-module wiring cable included with (60 only) Marked
More informationwww.greenelectricalsupply.com 1x4 2x2 & 2x4 Read all instructions and warnings before attempting installation. RISK OF FIRE OR ELECTRIC SHOCK. LED RETROFIT INSTALLATION REQUIRES KNOWLEDGE OF LUMINAIRES
More informationLED UFO High Bay with j-box Installation Instruction
Our new UFO style is the latest in LED technology. Smaller, longer lasting and more efficient. Less than 1 inches in diameter, the new design is more compact without sacrificing performance. The UHB series
More informationINSTALLATION GUIDE INSTALLATION GUIDE
INSTALLATION GUIDE INSTALLATION GUIDE CONTACT US By selecting a Haiku fan, you ve chosen quality design, heightened comfort and effortless conservation. Use this guide to safely install your fan. Please
More informationRound or Square Type Low-Profile Housing with Toroidal Transformer for Flangeless Trims E3_LF-HDSM-WR_ 1.0
Installation Instructions for 90EHMH-LNIC Round or Square Type Low-Profile Housing with Toroidal Transformer for Flangeless Trims E_LF-HDSM-WR_.0 HALOGEN MR - ROUND/SQUARE FLANGELESS GENERAL PRODUCT INFORMATION:
More informationINSTALLATION INSTRUCTIONS For Light*Waves Flex II Kit with 300-Watt remote transformer
IMPORTANT SAFETY INSTRUCTIONS READ ALL OF THESE BEFORE INSTALLING THE TRACK SYSTEM. SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES TO THE SYSTEM ARE MADE. THIS IS A 12-VOLT SYSTEM
More informationFOR SIT-STAND WORKSTATION
INSTALLATION MANUAL FOR SIT-STAND WORKSTATION Weight Capacity: 6.5-24.5 lbs. 6017180 Rev. B Contents Tools Required / Supplied Part Kits / Warnings/Disclaimers...2 Base Installation Clamp Mount Base Location...3
More informationLuminaire Support Location Cable Mounting Kit. Non-Power Feed
INSTALLATION INSTRUCTIONS These installation instructions are used for installing the following luminaires and kits: Luminaire Support Location Cable Mounting Kit OLE4 (suspended) Normal Power Feed Non-Power
More informationGEMINI HOUSING SPECIFICATIONS
GEMINI HOUSING SPECIFICATIONS GENERAL Gemini Housing shall support Track of six foot intervals. In addition, the extra compartment shall be able to be used for a multitude of elec trical or mechanical
More informationS HINE V ENTURE L IGHTING S LED LAMPS. Quality retrofit LED lighting products from a leader in the lighting industry. Full range dimming
S HINE V ENTURE L IGHTING S LED LAMPS Quality retrofit LED lighting products from a leader in the lighting industry Full range dimming Longer life and up to 90% energy savings Long product life and improved
More informationLynx, Voyager, Discovery, Adventurer. user manual
Lynx, Voyager, Discovery, Adventurer user manual ýìääåñýìäääýý0duwlqý3urihvvlrqdoý$î6ñý'hqpdunï $OOýULJKWVýUHVHUYHGïý1RýSDUWýRIýWKLVýPDQXDOýPD\ýEH UHSURGXFHGñýLQýDQ\ýIRUPýRUýE\ýDQ\ýPHDQVñýZLWKRXW SHUPLVVLRQýLQýZULWLQJýIURPý0DUWLQý3URIHVVLRQDOý$î6ñ
More informationTORi INSTRUCTION SHEET. Minimalist Linear Fixture T5/T5HO. CSS - Cable Suspended. 1. Cut cables to desired length - take care not to fray cable ends.
TORi Minimalist Linear CSS - Cable Suspended J-BOX (BY OTHERS) 3-O or 4-0 MUD RING (BY OTHERS) J-BOX BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS (BY OTHERS) CANOPY STND - 5 CANOPY 1. Cut cables to
More informationIdaho Profile System - Suspension
INDIRECT DIRECT ASY 3 1/8 80mm 2 15/16 75mm L3ID-SUS-SYS Article # Distribution Diffuser Length Angle Voltage Linear Spot x Qty Electrical Power Suspension Finishes Lighting Couplers Feed Cable Controls
More informationMALSR APPROACH LIGHTING. Medium-Intensity Approach Lighting System WITH ELEVATED SEQUENCED FLASHERS AND STEADY BURNING LIGHTS
Medium-Intensity Approach Lighting System WITH ELEVATED SEQUENCED FLASHERS AND STEADY BURNING LIGHTS Compliance with Standards FAA: Uses Designed according to FAA-E-2325 The approach lighting system with
More informationLights CONTINUED TURN SIGNAL/SIDE MARKER LIGHT HEADLIGHT PARKING LIGHT. Maintenance 237
Check the operation of your car s exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car s visibility and the ability to signal your intentions to
More information