Type V Accent Light Installation
|
|
- Lillian York
- 5 years ago
- Views:
Transcription
1 Packing List: Rheostat Assembly (with cover plate, knob, screws) Accent Light Assembly (with strain relief plate) (2) T4 Halogen Bulbs Bulb Type 35 Watt 120 Volt T4 Halogen Bulb (G6.35 Base) Installation Make sure power to the heater has been turned off prior to installation (disable the breaker). If using the optional firebacks, install them prior to the accent light. NOTE: The bulbs are shipped separately. Do not touc the bulb oil or other residue left on the bulb may lead to premature bulb failure. Use the packaging (or paper towel) to handle the bulb 1. Install the rheostat assembly as shown to the right. d Route the wiring harness under the burner to the back side of the fireplace. c Plug the power cord into the receptacle on the left side of the fireplace. a Attach the rheostat assembly to the fireplace with the two black screws. b Attach the quick connects from the rheostat assembly to the quick connects on the accent light assembly. NOTE: Make sure one white and one black wire attach to each pair of wires. Page 1 of 6 6/6/08 Travis Industries, Inc.
2 2. Remove the log shelf following the directions below. Remove the log shelf NOTE: The grate is not shown in the illustrations to better show component removal. It may be left in place during accent light installation. Page 2 of 6 6/6/08 Travis Industries, Inc.
3 3. Install the accent lights following the directions below. Remove the cover plate and a gasket under the firebox. b Insert the lamp bases through the gasket (removed in step a ) and into the area underneath the burners. The gasket fits snug around the strain relief. c Attach the strain relief bracket attached to the wiring harness to the firebox with the screws removed in step a. d Route the lamp bases to both sides of the burner. e Use a screwdriver to pry these two plates out 45 g Remove the lamp mounting bracket from the burner f (two holes are provided above the bracket to allow the screws to be removed). Install the bulb into the lamp base (do not touch the bulb - use the foam inside the packaging to handle). With the nuts on the back of the lamp base loosened several turns, slide it into the bracket. Tighten the nuts to secure. h Slide the bracket into place and secure using the screws removed in step f. NOTE When installing the logs and embers, place an ember in these two locations - this prevents light from exiting the crack and creating a beam of light. i Repeat steps e through h for the opposite side. Page 3 of 6 6/6/08 Travis Industries, Inc.
4 4. Make sure the wiring leading from the accent light to the strain relief is properly routed. Excess wire may be pulled through the strain relief. Make sure the wiring does not contact any of the burners or other hot surfaces. 5 Restore the fireplace to the correct configuration, restore power to the fireplace and test operation of the accent lights. Page 4 of 6 6/6/08 Travis Industries, Inc.
5 Optional Wall-Mounted Rheostat NOTE: Many areas require all wiring to be installed by a qualified electrician. Check with your local building official for any requirements in your area. 1 Remove the rheostat from the rheostat assembly. 2 Detach the three wires leading from the rheostat (secured with wire nuts). Attach the rheostat assembly to the fireplace (see step # 1 from the installation instructions). Attach the quick connects from the rheostat to the quick connects from the accent light assemblies (see step # 1 from the installation instructions). 3 Attach three suitable wires (insulated & sheathed) to the rheostat. Install the rheostat into a junction box at the remote location. Run the wire from the junction box to the fireplace. Use the included wire clamp to secure the wiring as it passes through the fireplace (see the illustration below). 4 Connect the three wires from the rheostat to the three wires on the wiring harness disconnected in step 2 (use the included wire nuts). Follow the instructions for installing the accent lights (step # 2 on). Rheostat (removed from rheostat assembly) Junction Box Romex Connector Knob (included) Rheostat Assembly A 7/8 diameter hole is provided on this cover plate (both sides). If this hole is already used for a gas inlet, you can drill an additional 7/8 hole in this cover plate. Page 5 of 6 6/6/08 Travis Industries, Inc.
6 Accent Light Operation OFF LOW HIGH Turn the dial all the way counter-clockwise until it clicks off. Turn the dial 180 clockwise until the light begins to glow. The high position is all the way clockwise. NOTE: The accent light responds best when turned to high, then turned down to the desired light level. Bulb Replacement NOTE: Do not touch the bulb oil or other residue left on the bulb may lead to premature bulb failure. Use the packaging (or paper towel) to handle the bulb. The bulbs must be replaced with 35 Watt 120 Volt T4 Halogen Bulbs (G6.35 Base) available at most hardware stores. To replace the bulb, simply remove it from the socket and insert the new bulb (pin orientation does not matter). Page 6 of 6 6/6/08 Travis Industries, Inc.
PARTS AND SERVICE MANUAL
PARTS AND SERVICE MANUAL FOR THE 23 INSERT FIREPLACE MODEL NUMBER: DFI2309 TABLE OF CONTENTS OPERATION PAGE 1 PARTS DRAWING PAGE 3 PARTS LIST PAGE 4 WIRING DIAGRAM PAGE 5 LIGHT BULB REPLACEMENT PAGE 6
More informationDVS Cypress Face Installation Instructions (SKU )
Table of Contents Compatibility... 1 Packing List... 1 Installation... 2 Prepare the Insert for Face Installation... 2 Attach the Surround Panels (if applicable)... 6 Assemble the Face... 7 Attach the
More informationService Manual. Model Number: DF2426GB DF2426SS DF2550 DF2562. UL Part Number to 500
Service Manual Model Number: DF2426GB DF2426SS DF2550 DF2562 UL Part Number 6905050100 to 500 IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to service this fireplace. For
More informationDVL Cypress Face Installation Instructions (SKU )
Table of Contents Compatibility... 1 Packing List... 1 Installation... 2 Prepare the Insert for Face Installation... 2 Assemble the Face... 6 Attach the Surround Panels (if applicable) and Face... 10 Hang
More informationService Manual Mozart Fireplace
Service Manual Mozart Fireplace Model Numbers: CFP3913 REV PCN DATE 00 11637 Sep 23, 09 Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N1R 7G8 1-888-346-7539 www.dimplex.com In
More information1080 CF Valve Replacement Instructions
Overview This kit includes the newer American Flame gas control valve designed specifically for the 1080 CF gas fireplace. If you have a 1080 CF fireplace, and you are uncertain as to whether this kit
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS IMPORTANT Before opening your Lights.com fixture, please make sure that you carefully read through these instruction sheets. Consider having your fixture installed by a qualified
More informationC35. Assembly Instructions. Mobius Floor Lamp & C Page 1 of 7. Prepare Base (Figures 1& 2)
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationINSTALLATION INSTRUCTIONS FOR PCDE-36VA CONVERSION KIT
INSTALLATION INSTRUCTIONS FOR PCDE-36VA CONVERSION KIT CONVERTING FROM NATURAL GAS TO PROPANE/LP GAS For Use When Converting Model (V)V36ENA Series This conversion kit must be installed by a qualified
More informationC35 Mobius Floor Lamp & C Page 1 of 7
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationINSTRUCTIONS. Power Panel. Installation Instructions
Overview LuXout Shade 18 Output - For use with LuXout Shades NOTICE: This power supply is built-in fan on/off control circuit. Fan automatically works according to working temperature. SHOCK HAZARD Risk
More informationFIREPLACE INSERT INTERIOR PARTS MODEL #'S: 0044, 0046, 1271 & 1272 FEATURES: 0044 WOOD INSERT WITH NO BRASS TRIM 0046 WOOD INSERT WITH BRASS TRIM 1271 COAL INSERT WITH NO BRASS TRIM 1272 COAL INSERT WITH
More informationMake sure all wiring is inserted into the cavity between the insert and the fireplace. Failure to do this may cause the wiring to become damaged.
Installation Notes Large Flush Wood Hybrid-Fyre Insert: (96400539, 96400539A) Before installing, make sure to install the one-piece panel, and disconnect the power cords making sure the Molex connector
More informationFOR SIT-STAND WORKSTATION
INSTALLATION MANUAL FOR SIT-STAND WORKSTATION Weight Capacity: 6.5-24.5 lbs. 6017180 Rev. B Contents Tools Required / Supplied Part Kits / Warnings/Disclaimers...2 Base Installation Clamp Mount Base Location...3
More information564 Shadowbox Face (w Screen) Instructions
Packing List Compatibility Face Bottom Shield (2) Face Brackets (8) Screws (#8 x 3/8 Phillips) (5) Screws (#8 x 5/8 hex head) Drill Template 11/64 Drill Bit Items Used with Optional Switch Box (see note
More informationService Manual. Model Number UL Part Number BF33STP BF33DXP BF39STP BF39DXP BF45DXP
Service Manual Model Number UL Part Number BF33STP 6901811400 BF33DXP 6901811500 BF39STP 6901811600 BF39DXP 6901811700 BF45DXP 6901811900 DXP Model Shown IMPORTANT SAFETY INFORMATION: Always read this
More informationGreenStart Igniter for Inserts: Installation Instructions (SKU )
Compatibility Flush Wood Plus Rectangular SN #1401-10265 or greater Flush Wood Plus Arch SN #1401-10106 or greater Flush Wood Plus Cape Cod Large Flush Wood Insert NOTE: Use the firebrick and igniter housing
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationAssembly Guide ELECTRIC. Model Numbers: C1. (English) /14/11
Assembly Guide Model Numbers: 12601559 12601578 12601663 12601664 12601665 12601688 12601514 12601514-C1 ELECTRIC (English) 42804641 09/14/11 2 ASSEMBLY GUIDE A, B, C, Assembly: CAUTION: For your safety,
More informationMODEL RVS304. REMOTE CONTROLLED SAFETY PILOT KIT Supplemental Installation Instructions for use with Natural Gas Log Sets
MODEL RVS304 REMOTE CONTROLLED SAFETY PILOT KIT Supplemental Installation Instructions for use with Natural Gas Log Sets NOTE: This kit is for both Natural Gas and LP Gas applications. For LP (Propane)
More informationWARNING. Important Notice
CAL (Color AquaLuminator ) Light and Return Water Flow for Above Ground Pools Owners Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION
More informationInstruction Sheet P/N _01 3/2013
Instruction Sheet P/N 222_0 3/203 AltaBlue TT Melter Service Kit - P/N 249 This instruction sheet describes the upgrade or replacement of the motor assembly in the AltaBluet TT adhesive melter, model A4TP,
More informationDVM36/42 SERIES LOG SET/BURNER MODULES INSTALLATION INSTRUCTIONS
DVM36/42 SERIES LOG SET/BURNER MODULES INSTALLATION INSTRUCTIONS For Use With (V)TC36 Series, (V)VC36/42 Series, (V)KC36/42 Series or DVC Series Fireplaces This log set/burner module must be installed
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
AQUALUMINATOR & AQL LIGHT AND RETURN WATER FLOW FOR ABOVE GROUND SWIMMING POOLS INSTALLATION AND USER'S GUIDE Contents SECTION I. IMPORTANT SAFETY INSTRUCTIONS... 2 SECTION II. LAMP HOUSING INSTALLATION...
More informationDry Contact Closure Interface
Dry Contact Closure Interface Overview LuXout Shades Dry Contact Closure Contact closure interfaces allows integration of the Automation systems throughout the house. The contact closure interface communicates
More informationFan, DVI Insert 31 and 33 DVI Installation Instructions (sku )
Packing List Fan, DVI Insert 31 and 33 DVI Left and Right Blower Assembly (with grommets and bushings) (2) Blower Mounting Nuts Wiring Harness Rheostat Snap Disc Rheostat Nut and Knob Nylon Rheostat Spacer
More informationMODEL SCA Installation and Operation Manual Important:
MODEL SCA Installation and Operation Manual Important: This manual contains specific cautionary statements relative to worker safety. Read this manual thoroughly and follow as directed. It is impossible
More informationM GT 2005 up Mustang ENGINE START Push-Button INSTRUCTION SHEET
Please contact the Ford Racing Techline for the most current instruction information @ (800) FORD-788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The following
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
1 AQUALUMIN III NICHELESS POOL LIGHT INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationINSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER
Form 5063T, 06-05 Supersedes Form 5063T, 02-04 INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER This document provides the information needed to install the DSP9600/9100 Wheel Balancer. NOTE:
More informationStep 2 Insert the LEGS into the LEG CROSS BARS as shown below. Lock Washer. Long Legs. Wheel Axle. Cotter Pin. Hub Cap. Washer
Assembly Instructions Step 1 Attach the LONG LEGS and SHORT LEGS to the base, opposite the tank well/hole with two (2) lock washers ½ Bolts as shown below. Lock Washer Long Legs Step 2 Insert the LEGS
More informationOWNER S MANUAL AND INSTALLATION INSTRUCTIONS
EmerGen Switch Manual Transfer Switch OWNER S MANUAL AND INSTALLATION INSTRUCTIONS For A Series Models 6-5001, 6-7501, 10-7501, 10-12K1 PLEASE READ THIS MANUAL IN ITS ENTIRETY BEFORE INSTALLING AND/OR
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
5 Swift Lock Ready Shape Tree (Patent Pending) Instructions IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: READ AND FOLLOW
More informationAquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
16 1 AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationSIT Pilot Assembly Retrofit - # 308 (Replaces R. Shaw Pilot Asbly) (SKU # )
Check Condition of Shipment SIT Assembly Retrofit - # 308 Upon receipt of this kit, check the condition of the packaging. Damage to the package should be noted on the carrier's freight receipt. Any damage
More informationOPERATING & SERVICE PARTS MANUAL SM20ES ENERGY SMART WRAPPER
OPERATING & SERVICE PARTS MANUAL SM20ES ENERGY SMART WRAPPER Series B Model SM20ESC6 Cradle Mount Model SM20ESC6 Cradle Mount Shown with Optional Left & Right Wings Model SM20ESC6 Cradle Mount Shown with
More informationassembly guide ELECTRIC Model Numbers: Estimated time required for assembly: 1 Hour (English) /02/10
assembly guide Model Numbers: 11601514 11601559 11601578 Estimated time required for assembly: 1 Hour ELECTRIC (English) 42804382 6/02/10 2 ASSEMBLY GUIDE A, B, C, Assembly: CAUTION: For your safety, before
More informationTroubleshooting Guide: 355 Lights (24V)
Troubleshooting Guide: 355 Lights (24V) Contents Description Refer To: Troubleshooting - Troubleshooting Chart Adjustments / Repair Procedures Bulb Replacing the Bulb Fuse(s) Replacing the Fuse (Ceiling)
More informationIMPORTANT SAFETY INFORMATION
Service Manual Model BLF50 UL Part Number 6906780100 IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to service this fireplace. For your safety, always comply with all warnings
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationLAMPS 8L - 1 LAMPS CONTENTS
PL LAMPS 8L - 1 LAMPS CONTENTS BULB APPLICATION... 8 LAMP BULB SERVICE... 2 LAMP DIAGNOSIS... 1 LAMP SERVICE... 5 LAMP DIAGNOSIS HEADLAMP LEVELING MOTOR... 1 INDEX HEADLAMP LEVELING MOTOR This vehicle
More informationTroubleshooting Guide: 355 Lights (12V)
Troubleshooting Guide: 355 Lights (12V) Contents Description Refer To: Troubleshooting - Troubleshooting Chart Adjustments / Repair Procedures Bulb Replacing the Bulb Fuse(s) Replacing the Fuse (Ceiling)
More informationMEDIA LED. Pendant Standard Mount Installation ou de montage WARNING:
MEDIA LED Pendant Standard Mount WARNING: Disconnect main power at the source prior to installation! Thread gripper base onto 1 /4 20 stud, or with #8 screw. Depress gripper nozzle to insert aircraft cable.
More informationSection 7 - Troubleshooting Guide
Section 7 - Troubleshooting Guide Section 7 - Troubleshooting Guide IMPORTANT While this troubleshooting guide provides information to aid in troubleshooting problems with the range, it does not contain
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationLiteBox /FireBox / Operating Instructions. (Rechargeable) 99 Washington Street Melrose, MA Phone Toll Free
LiteBox /FireBox / E-Flood /E-Spot (Rechargeable) Operating Instructions 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com ENGLISH
More informationUniversal Bench-top Conveyor OPERATOR S GUIDE
OPERATOR S GUIDE DISCLAIMER LIABILITY LIMITATION: The Buyer of this product accepts full responsibility and understanding for the terms and specifications set forth herein. Con-Trol-Cure makes no claim,
More informationNSGV PT-1000 PORTABLE WELDING STATION I, O & M MANUAL
APPLICATION OF DUST CONTROL EQUIPMENT: CAUTION - Warning Improper operation of dust control system may contribute to conditions in the work area or facility that could result in severe personal injury
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
7.5 Swift Lock Ready Shape Tree (Patent Pending) Instructions IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: READ AND
More informationInstallation Instructions
Please read all instructions before installing CD-250 Multi-way Dimming Wall Switch Vacancy Sensor Lens Air Gap Isolation Switch Lighted Switch ON/OFF/DIM button SPECIFICATIONS Voltage...120VAC, 60Hz Load
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-SCV-102 2008 ELEMENT AII 36531 Issue Date MAY 2007 PARTS LIST 15 Wire ties 2 Fog lights 4 Wire ties with clip Switch harness
More informationDeSoto NEMA 4X EMERGENCY LIGHTING UNIT. U.S. Versions: 6V- DM90X618 / DM90X654 12V- DM90X1254 / DM90X12100 INSTALLATION INSTRUCTIONS
DeSoto U.S. Versions: 6V- DM90X618 / DM90X654 12V- DM90X1254 / DM90X12100 NEMA 4X EMERGENCY LIGHTING UNIT INSTALLATION INSTRUCTIONS U.S. Patent No.s 6,135,624; 6,193,395; 6,502,044 B1; D505,222; IMPORTANT
More informationSelf-Testing Industrial Series
Series: AS-I (Maint.-Free) Self-Testing Industrial Series Emergency Lighting Equipment Instructions for INSTALLATION OPERATION SERVICE SPECIFICATIONS 1300650 1300654 1300666 1300754 1300823 1300886 Hubbell
More informationDemand Switch NEFA20 Plus. Installation Guide. Please read this entire guide before beginning the installation!
Demand Switch NEFA20 Plus Installation Guide Please read this entire guide before beginning the installation! Supplied Parts Protective Covers DIN Mounting Rail NEFA20 Plus Mounting Rail Spacer Warning
More informationASSEMBLY INSTRUCTIONS PRODUCT CODE: CAUTION: Carefully Read Instructions and Procedures for Safe Operation. 7' Diamond Peak LED Tree
7' Diamond Peak LED Tree ASSEMBLY INSTRUCTIONS MODEL NO: U11G684A-024-01 (WL-019) PRODUCT CODE: 140-034067-090 CAUTION: Carefully Read Instructions and Procedures for Safe Operation. Receipt of Purchase:
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationD-4D Injector Install procedure
D-4D Injector Install procedure 2011 Diesel Toyz llc About this manual Disclaimer This manual is intended to serve as an overall guide to perform the procedure outlined within. Diesel Toyz llc accepts
More informationPush Start Ignition (05-10 All) Installation
Tools Required: Phillips head screwdriver Flat head screwdriver Ratchet 7mm Socket Torx T20 bit Wire strippers/cutters Hand file Needle nose pliers Installation Instructions: Push Start Ignition (05-10
More information200 Shadylane Drive Philipsburg, PA Phone: (814) Fax: (814) Service Manual. Model 642E Centrifuge
200 Shadylane Drive Philipsburg, PA 16866 Phone: (814) 342-6205 Fax: (814) 342-4510 www.druckerdiagnostics.com Service Manual Model 642E Centrifuge MODEL 642E SERVICE MANUAL REV: Original Issue 1 CONTENTS
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More information2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit INSTALLATION GUIDE FOR RACING USE ONLY
INSTALLATION GUIDE 2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit FOR RACING USE ONLY Congratulations on your purchase of the AWE Tuning S-FLO Intake for the 2010+ Audi B8 S4 and B8 S5 3.0T. Exquisite build
More informationCharcoal Filter Installation NOTE: The charcoal filters are preinstalled if you purchased the range hood with re-circulating kit from us. 1. Remove st
Venting Methods This range hood is factory set for venting through the roof or wall. For non-vented (re-circulating) installations, see Ductless Conversion on Page 7. Vent work can terminate either through
More informationRigMaster Power Service and Repair Manual Document # S901009
Document # S901009 WARNING The following procedures present hazards which can result in injury or death. Only persons qualified to carry out electrical and mechanical servicing should undertake this work.
More informationSMIDLEY MINI-SCALE RETROFIT INSTRUCTIONS
TM SMIDLEY MINI-SCALE RETROFIT INSTRUCTIONS Rev. Aug 2015 Smidley Mfg. Inc. Britt, Iowa 50423 800-392-5632 Toll Free www.smidley.com SMIDLEY MINI-SCALE RETROFIT INSTRUCTIONS You have a timeless Smidley
More informationETF-600 Sensor Operated Lavatory Faucet
INSTALLATION INSTRUCTIONS OPTIMA SYSTEMS SENSOR OPERATED LAVATORY FAUCET ETF-600 I.I. Code No. 0816318 ETF-600 Sensor Operated Lavatory Faucet Includes Instructions for Installation of Optional Back Checks
More informationInstallation & Operation Instructions. Deluxe LED Spot Light
Installation & Operation Instructions Deluxe LED Spot Light 405626-3 To avoid the risk of accidents or damage to this product, it is essential to read these instructions thoroughly SDG Edition before this
More informationRemove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
More informationPortable Lighting Equipment Operating Instructions Table of Contents
Portable Lighting Equipment Operating Instructions Table of Generac Magnum Ingersoll Rand TEREX AMIDA TEREX GENIE Model: MLT3060 Model: LIGHTSOURCE Model: Amida AL4000 series Model: TML4000N Generac Magnum
More informationSpectron Industrial Series
1300650 1300654 1300666 1300754 1300823 1300886 Table B Constant Value per Voltage System Wire Size (Maximum Voltage Drop 5%) System 6 Volt 12 Volt 24 Volt Wire Size #12 #10 #8 #6 #12 #10 #8 #6 #10 #12
More informationSolar Flood Light. Instruction Manual Models: GS-203, GS-203-WW
Solar Flood Light Instruction Manual Models: GS-203, GS-203-WW Introduction Thank you for your purchase! GAMA SONIC solar charged accent lighting eliminates the problems associated with most solar lighting
More informationLT Charging Cart for Laptops
Built with Anthro-DNA LT Charging Cart for Laptops Owners Manual This unit has been tested to Underwriters Laboratories U.S. and Canadian (Bi-National) Standard for Safety of Informational Technology Equipment,
More informationDeSoto EMERGENCY LIGHTING UNIT. U.S. Versions: 12V- DM (P2 & P3) / DM / DM INSTALLATION INSTRUCTIONS
DeSoto U.S. Versions: 12V- DM80212100 (P2 & P3) / DM80212150 / DM80212450 EMERGENCY LIGHTING UNIT INSTALLATION INSTRUCTIONS U.S. Patent No.s D419,097; 6,135,624; 6,193,395; 6,502,044 B1 Canadian Patent
More informationAdjustable Light Kits E-Z-Go TXT All Models Installation Instructions
Adjustable Light Kits E-Z-Go TXT All Models 1996-2013 Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationPRELIMINARY INSTALLATION INSTRUCTIONS PARTS LIST. Combination light switch Right fog light. 4 Self-tapping washer-screws.
INSTALLATION INSTRUCTIONS Accessory S P/N 08V31-SCV-100D Application 2009 ELEMENT (SC) Publications No. AII 40515 Issue Date OCT 2008 PARTS LIST Combination light switch Right fog light Left fog light
More informationRated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications
WPC1-XXXX-T Rated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications Installation Instructions: Read these instructions in their entirety before performing any installation work. FOR USE WITH
More informationA B C D E F. Tools Required (supplied by others)
Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)
More informationAnchorage SS Center Model AN3050. Installation, Maintenance, and Operation Manual
Anchorage SS Center Model AN3050 Installation, Maintenance, and Operation Manual Rev.3 06-29-16 Marina Electrical Equipment, Inc. 100 Warwick Court Williamsburg, VA 23185 Toll Free: 1-855-258-3939 Fax:
More informationInstallation Instructions Rotation Control Kit
Installation Instructions Rotation Control Kit 45-101, REV. 11/14 1 TABLE OF CONTENTS SECTION 1 PURPOSE... 3 SECTION 2 INSTALLATION... 4 Test Installation...6 Disabling The System...6 Operation...6 2 45-101,
More informationA B C D E F. b.tools Required (supplied by others) 3/16" Drill Bit 3/8" Wrench Phillips Head Screwdriver
Page 1 of 13 5E.1 Parts List a. Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel with Motor Attached (B) (1) Rope Reel Cover (C) (1) Cover Drum (1) Cover
More informationASSEMBLY INSTRUCTIONS
6.5' McKinley Pine ASSEMBLY INSTRUCTIONS MODEL NO: U11G681A-024-01 (WL-018) PRODUCT CODE: 140-034066-910 CAUTION: Carefully Read Instructions and Procedures for Safe Operation Receipt of Purchase: Questions,
More information9' Warm White /Multi LED Color Changing M5 One Plug tree V INSTRUCTION MANUAL
9' Warm White /Multi LED Color Changing M5 One Plug tree V64886-60 INSTRUCTION MANUAL Thank you for purchasing a SYLVANIA Pre-lighted Tree. This tree assembles in minutes and is decorated with energy saving
More informationChecker Unload Checkstand Installation Instructions
Front-End Checkouts Commercial Refrigeration Equipment Display Merchandisers Store Fixtures Checker Unload Checkstand Installation Instructions Attention Store Manager: Please find enclosed in this packet
More informationELS Electronic Lighting System
ELS Electronic Lighting System T-8 Lamp Replacement November, 2012 99-20374-I001 I. T-8 Lamp Replacement Instructions Center Mullion Fixtures 1. Turn light power off before start of lamp replacement. 2.
More informationChain/Belt Drive Models PRE-INSTALLATION CONSIDERATIONS
38968503545. 08/2017 ASSEMBLY/INSTALLATION Chain/Belt Drive Models PRE-INSTALLATION CONSIDERATIONS This opener includes parts and supplies needed for installation in most garages and on most garage doors.
More informationProper installation of this product requires the installer to have a good understanding of automotive electronics, systems and procedures.
ENGINEERING COMPANY INC. 51 Winthrop Road Chester, Connecticut 06412-0684 Phone: (860) 526-9504 Fax: (860) 526-4078 Internet: www.whelen.com Sales e-mail: autosale@whelen.com Canadian Sales e-mail: autocan@whelen.com
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationTHIS GUIDE IS INTENDED FOR DEALERS AND SOLAR COMFORT TECHNICIANS ONLY AND IS NOT MEANT OR INTENDED TO BE REPRODUCED OR DISTRIBUTED TO THE CONSUMER
THIS GUIDE IS INTENDED FOR DEALERS AND SOLAR COMFORT TECHNICIANS ONLY AND IS NOT MEANT OR INTENDED TO BE REPRODUCED OR DISTRIBUTED TO THE CONSUMER Table of Contents Page Tools Needed (A) 3 Replacement
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-SCV-100B 2008 ELEMENT (SC) AII 36532 Issue Date MAY 2007 PARTS LIST Relay bracket Right fog light Relay Left fog light Fuse
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationPN PONTIAC FIREBIRD. Kit Contents: Four Panel Sequential LED Tail Light Kit Installation Guide
1969 PONTIAC FIREBIRD Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire 2 pigtail harness kits 2 crimp terminal kits PN 1100569 1969
More informationSection II - Installation Procedures Part Number : Accessory Code IL1 Kit Contents. Color Applicability/Trim Level. Hardware Bag Contents
Document # 10.21.00 PIO/DIO 01/14/09 TOYOTA Rav-4 2009- INTERIOR InteriorLIGHT Light UPGRADE Upgrade Part Number : 00016-00065 Accessory Code IL1 Kit Contents Color Applicability/Trim Level Item # Quantity
More informationINSTALLATION INSTRUCTIONS
144F TABLE OF CONTENTS GENERAL... 2 SPECIFICATIONS... 2 PACKAGE CONTENTS... 2 PACKAGE CONTENTS: ACCESSORIES... 3 REQUIRED TOOLS... 3 ADD-ON COMPONENTS... 3 CABINET MOUNTING WALL MOUNT BRACKET ATTACHMENT...
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 23092 KIT CR-V P/N 08A55-S9A-100 Issue Date NOV 2001 PARTS LIST 2 Tweeters INSTALLATION Customer Information: The information in this
More informationMODELS: SPL-12W, SPL-12B, SPL-12C IMPORTANT! READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.
502-2 & 503-2 Instructions instructions marinco.com Installing and Using the Precision Spotlight MODELS: SPL-12W, SPL-12B, SPL-12C IMPORTANT! READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.
More informationNOTE. Figure 2. Mounting Configurations (View shown from rear of LED Bar) Figure 3. Rear Deck Mounting NOTE
Page 5 Page 6 TO REAR OF VEHICLE (STANDARD WIRING) LIGHTBAR 2 TO FRONT OF VEHICLE (OPTIONAL WIRING) LIGHTBAR 1 LIGHTBAR 1 LIGHTBAR 2 Figure 2. Mounting Configurations (View shown from rear of LED Bar)
More informationNOTE. Figure 2. Mounting Configurations (View shown from rear of LED Bar) Figure 3. Rear Deck Mounting NOTE
Page 5 Page 6 TO REAR OF VEHICLE (STANDARD WIRING) LIGHTBAR 2 TO FRONT OF VEHICLE (OPTIONAL WIRING) LIGHTBAR 1 LIGHTBAR 1 LIGHTBAR 2 Figure 2. Mounting Configurations (View shown from rear of LED Bar)
More informationSYSTIMAX SMB-4-3/4, SMB-8-1/2 Shelf-Mounted Cable Bracket Kits and 1000G2-XCPB Expanded Cable Protector Kit
Instruction Sheet 860380799 SYSTIMAX Solutions SYSTIMAX SMB-4-3/4, SMB-8-1/2 Shelf-Mounted Bracket Kits and 1000G2-XCPB Expanded Protector Kit General The SYSTIMAX SMB-4-3/4 and SMB-8-1/2 shelf mounted
More informationNOTE: The orientation of the mounting brackets are critical. (See Figure 4)
Page 1 of 5 11.25.13 Lamping Specifications 10138 I-wall 2 120v, One, F14WT5/Mini Bi-Pin 277v, One, F14WT5/Mini Bi-Pin 10139 I-wall 3 120v, One, F21WT5/Mini Bi-Pin, 277v, One, F21WT5/Mini Bi-Pin 10140
More information