Base Power Infeed Installation for Training Tables with Modular Table Power System
|
|
- Ralf Robinson
- 6 years ago
- Views:
Transcription
1 Base Power Infeed Installation for Training Tables with Modular Table Power System Topic Table of Contents General Safety Warnings Base Power Infeed Usage Electrical Circuits Base Power Infeed - 0 Amp Plug Base Power Infeed - Hardwire Hardwire Power Infeed Tether Base Power Infeed Assemblies Page CABLE LENGTH 1" MAX. 1. For use in indoor, dry locations only.. Read and install in accordance with all assembly directions. 3. Only connect to products labeled "Modular Table Power System" by Steelcase. 4. Do not modify or strain cables. If damaged, remove from service immediately. 5. Disconnect modular electrical connections before servicing or reconfiguring tables. 6. Tables must be held together with ganging hardware as described in this document, and NOT held together solely by electrical components. 7. Cable clamps must be no more than 1" from modular cable end connector or receptacle. Installing Hardwire Infeed Installing 0 Amp Plug Infeed " MAX. Base Power Infeed Usage A base power infeed is required to provide power to Modular Table Power Kits. All power infeeds have a female connector. Two versions of infeeds are available: -0 Amp plug - The 0-amp plug infeed is used when reconfigurability is needed, and does not require an electrician. The plug infeed can only be used with circuit-1 receptacles. -Hardwire - When the installation is permanent or local electrical codes are restrictive, the hardwire base power infeed is available. This infeed must be installed by a licensed electrician in compliance with all local and national codes. The hardwire infeed can be used with circuit-1 and circuit- receptacles. Electrical Circuits Runner Non-folding Plug and Play Table Train Tables Akira Folding and Fixed Tables The modular table power kit is a 0 Amp, 4-wire, -circuit system. The 0 Amp plug infeed allows up to 13 circuit-1 duplex receptacles. The hardwire infeed allows up to 13 duplex receptacles per circuit for a total of 6. The duplex receptacle(s) in the table power kit and every two simplex receptacles from the desktop module count against the 13 duplex receptacles allowed for each circuit. Receptacle faces on the Modular Table Power Kits are marked I, for circuit 1 and II, for circuit. If you have a problem, question, or request, call your local dealer, or Coalesse at Or visit our website: Coalesse San Francisco, California U.S.A. Printed in U.S.A. Page 1 of 6
2 Base Power Infeed - 0 Amp Plug The plug base power infeed is a single-circuit (circuit 1) power infeed with 4" of rubber cord and a 0-Amp plug on one end coupled to 48" of flexible steel conduit with a female modular connector on the other end. Base Power Infeed - Hardwire The hardwire base power infeed is a two-circuit (circuits 1 & ) flexible steel conduit with a 4-wire pigtail for hardwire connection on one end and a female modular connector on the other end. Hardwire Power Infeed Tether A flexible braided steel tether is included with the hardwire power infeed kit. The tether anchors the table to the building, preventing disengagement of electrical connections. The first table in a series of tables connected with power, must be anchored in place with the tether. The tether provided is 1" shorter than the hardwire infeed cable. If the hardwire infeed cable is shortened, the tether must also be shortened to maintain the structural connection. The tether length between its connection to the table and the building must always be shorter than the hardwire infeed length between its modular connection and the building. An extra loop and crimp are provided for the cut end of the tether. Neutral Ground Not Used Hot 1 CIRCUIT 1 0 AMP PLUG SCHEMATIC White, 1 GA Green or no coating, 1 GA Red Black, 1 GA Note: all electrical installations must be reviewed with the local authority for compliance with local code, and must be performed by a qualified person in accordance with codes and regulations applicable at the installation site. Base Power Infeed - 0 Amp Plug Neutral Ground Hot Hot 1 White, 1 GA Green or no coating, 1 GA Red, 1 GA Black, 1 GA Base Power Infeed - Hardwire CIRCUIT 1 CIRCUIT HARDWIRE SCHEMATIC Hardwire Power Infeed Tether Page of 6
3 Base Power Infeed Assemblies 0 Amp Plug Hardwire SHIPPED COMPONENTS: - 1 cable/cord assembly - 1 hardware kit SHIPPED COMPONENTS: - 1 cable assembly - 1 hardware kit HARDWARE: - #10 phillips head screws/black - cushioned clamps TOOLS REQUI: - drill and.157" dia. drill bit - # phillips head driver HARDWARE: - 1 tether assembly - 1 thumb screw - #10 philips head screws/black - Cushioned Clamps - 1 loop - 1 crimp TOOLS REQUI: - drill and.157" dia. drill bit - # phillips head driver - crimping tool required if tether is shortened. FEMALE CONNECTOR Runner Table Shown TETHER 3 HARDWIRE INFEED TO BUILDING POWER SUPPLY OPTIONAL VERTICAL WIRE MANAGER Installing Hardwire Infeed 1. Determine location of building power supply.. Determine which table will be first in the series and where power infeed will connect to modular cable. Note: All power infeed cables have a female connector. 3. Determine power infeed cable routing. Recommended routings include: - Along table leg - Through optional vertical wire manager (Runner & Akira only) - Directly into wall CONDUIT SNAP-CLIP 6 4 TIP: Place a shim under rug to allow a finger hold when assembled unit is ready to upright. 4. Carefully place table upside down onto rug or other soft, clean surface. 5. Remove ganging hardware from corner of table where power infeed will be connected. MALE CONNECTOR 5 FEMALE CONNECTOR GANGING HARDWARE 6. Remove modular cable end from conduit snap-clip at corner of table where infeed will be connected; then remove snap-clip. Note: Snap-clip is not required for fastening modular cable. Page 3 of 6
4 Installing Hardwire Infeed (continued) Male end of Modular Table Power Cable Female end of Base Power Infeed Cable 7. Insert thumb screw through tether loop. 8. Locate threaded insert near end of table where infeed will be connected. Attach tether to table by fastening tether loop and thumb screw assembly into threaded insert. Table Run Note: Latches fully engaged. Building Power Supply THUMB SCREW TETHER LOOP 7 TETHER LOOP & THUMB SCREW ASSEMBLY. Connect power infeed to modular cable. - Match like colors only. (Green-to-Green, Red-to-Red, Black-to-Black and White-to-White). Push connectors together until both latches engage. 10. Relocate conduit clamp. Mark mounting hole location. - Do not allow more than 1" of cable between modular connector and clamp. 11. Wrap first cushioned clamp around Base Power Infeed conduit between shrink-wrapped ground wire and ID label. Wrap second clamp approximately 1/4" from first, but with mounting hole location on opposite side of the conduit. Mark mounting hole locations. - Ensure both cushioned conduit clamps are positioned per artwork shown. Note: Orient colors on both connectors to match. Note: Cable inside bend radius must not be less than 1.50". 1. Drill pilot holes for clamps.157" diameter by.50" deep, then fasten clamps. 13. Carefully flip tables upright into use position, and make ganging connection(s). 14. Securely anchor tether to building. CONDUIT CLAMP 10 1 CONNECTION TO CUSHIONED CLAMPS ID LABEL.5" TETHER LOOP & THUMB SCREW ASSEMBLY Connect hardwire infeed to building power. - Connection must be performed by a qualified person following local and national electrical codes. SHRINK-WRAPPED GROUND WIRE 11 Page 4 of 6
5 Installing 0 Amp Plug Infeed 1. Determine location of power outlet in wall or floor of building.. Determine which table will be first in the series and where power infeed will connect to modular cable. Note: All power infeed cables have a female connector. 3. Determine power infeed cable routing. Recommended routings include: - Along table leg - Through optional vertical wire manager (Runner & Akira only) - Directly into wall 4. Carefully place table upside down onto rug or other soft, clean surface. FEMALE CONNECTOR Runner Table Shown OPTIONAL VERTICAL WIRE MANAGER TO BUILDING POWER SUPPLY 5. Remove ganging hardware from corner of table where power infeed will be connected. 6. Remove modular cable end from conduit snap-clip at corner of table where infeed will be connected, then remove snap-clip. Note: Snap-clip is not required for fastening modular cable. 4 TIP: Place a shim under rug to allow a finger hold when assembled unit is ready to upright. CONDUIT SNAP-CLIP 6 MALE CONNECTOR FEMALE CONNECTOR 5 GANGING HARDWARE Page 5 of 6
6 Male end of Modular Table Power Cable Female end of Base Power Infeed Cable Installing 0 Amp Plug Infeed (continued) 7. Connect power infeed to modular cable. - Match like colors only. (Green-to-Green, Red-to-Red, Black-to-Black and White-to-White). Push connectors together until both latches engage. 8. Relocate conduit clamp. Mark mounting hole location. - Do not allow more than 1" of cable between modular connector and clamp.. Wrap first cushioned clamp around Base Power Infeed conduit between shrink-wrapped ground wire and ID label. Wrap second clamp approximately 1/4" from first, but with mounting hole location on opposite side of the conduit. Mark mounting hole locations. - Ensure both cushioned conduit clamps are positioned per artwork shown. 10. Drill pilot holes for clamps.157" diameter by.50" deep, then fasten clamps. Table Run Note: Latches fully engaged. 7 Note: Orient colors on both connectors to match. Note: Cable inside bend radius must not be less than 1.50". Building Power Supply 11. Carefully flip tables upright into use position, and make ganging connection(s). 1. Plug cord into 0 Amp electrical outlet. CONDUIT CLAMP 8 10 CONNECTION TO 7 ID LABEL CUSHIONED CLAMPS 10.5" SHRINK-WRAPPED GROUND WIRE Page 6 of 6
Assembly and Modular Table Power System Installation Instructions for Train Tables
Assembly and Modular Table Power System Installation Instructions for Train Tables Table of Contents Topic Attach Stretcher to Legs Attach Base To Table Top Attach Modesty Panel to Assembly Page 2 3 4
More informationPower In - Pathways Technology Wall
Power In - Pathways Technology Wall NOTE: With an off module application involving the transition of cabling or electrical harnesses, you will have to drill a maximum of a 2-1/2" hole in the beltway trim
More informationidrive Power Cord Extender Installation Instructions MODELS: 3960M/3961S (1) 25 POWER CORD DRILL WITH 3/32 DRILL BIT
Wayne-Dalton Corp. P.O. Box 67 Mt. Hope, OH 44660 (888) 827-3667 www.wayne-dalton.com idrive Power Cord Extender Installation Instructions MODELS: 3960M/3961S The idrive Power Cord Extender is intended
More informationOFFICE PARTITIONS. Data Port Openings. Use cable tie bracket to dress data cables under panels. STEP 1
N Power Box Opening Data Port Openings Rear View Front View Remove opening blanks on raceway cover for power and data. If panel contains no electric or data and is used as a pass-thru, leave opening blanks
More informationC35. Assembly Instructions. Mobius Floor Lamp & C Page 1 of 7. Prepare Base (Figures 1& 2)
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationAssembly Guide ELECTRIC. Model Numbers: C1. (English) /14/11
Assembly Guide Model Numbers: 12601559 12601578 12601663 12601664 12601665 12601688 12601514 12601514-C1 ELECTRIC (English) 42804641 09/14/11 2 ASSEMBLY GUIDE A, B, C, Assembly: CAUTION: For your safety,
More informationUniversal Storage - Storage/Wardrobe/Combo Cabinets/Lateral Files
Universal Storage - Storage/Wardrobe/Combo Cabinets/Lateral Files Storage Wardrobe Table of Contents Stack and Rotate Lateral File Combo Cabinet If you have a problem, question, or request, call your local
More informationINSTALLATION INSTRUCTIONS SEMI-HIDDEN WINCH MOUNT Part Number:70005 Application: Ford Super Duty
INSTALLATION INSTRUCTIONS SEMI-HIDDEN WINCH MOUNT Part Number:70005 Application: Ford Super Duty Your safety, and the safety of others, is very important. To help you make informed decisions about safety,
More informationRoller Shades CORD LOOP. Head Rail, Fascia and No Head Rail. Installation & Care Instructions
Roller Shades CORD LOOP Head Rail, Fascia and No Head Rail Installation & Care Instructions 152038 H 5/30/2017 GETTING STARTED A few simple tools are required: - Measuring tape - Power drill, drill bits
More informationassembly guide ELECTRIC Model Numbers: Estimated time required for assembly: 1 Hour (English) /02/10
assembly guide Model Numbers: 11601514 11601559 11601578 Estimated time required for assembly: 1 Hour ELECTRIC (English) 42804382 6/02/10 2 ASSEMBLY GUIDE A, B, C, Assembly: CAUTION: For your safety, before
More informationINFINITY MULTA SERIES
ASSEMBLY ASSEMBLY INSTRUCTIONS INSTRUCTIONS ASSEMBLY INSTRUCTIONS INFINITY MULTA SERIES Workstations, WORKSTATIONS, desks, DESKS, and AND tables TABLES with WITH powered POWERED ADJUSTMENT adjustment PARTS
More informationAssembly of kick TM Utility Poles
Assembly of kick TM Utility Poles #2 Phillips screwdriver 3/16" Ball-End Allen Bit with 6" Extension WARNING: If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at
More informationHaworth prices in this book will increase on March 1, 2017 by 4% Intuity Benching North America Specification Guide / Price List June 2015
Haworth prices in this book will increase on March 1, 2017 by 4% Intuity Benching North America Specification Guide / Price List June 2015 Electronic Update Page Intuity Benching Price List The table below
More informationInstallation Instructions for SINGLE COLOR 24V LINEAR LED NEON
Installation Instructions for SINGLE COLOR 24V LINEAR LED NEON LLI-N2.9W Prior to installation, please confirm that you have the required system components listed below. LED Neon Flow Extrusions/Lens (Optional)
More informationINTERWORKS EQ. Table of Contents. Panel System. Interworks EQ Kimball Legacy. Price List Effective Dates: Pricing Revision
INTERWORKS EQ Table of Contents Price List Effective Dates: 07.02.18 Revision 06.15.18 See page Statement of Line page 14.2 Panels, Connectors, Trim page 14.2 Power and Data page 14.3 Overview page 14.4
More informationC35 Mobius Floor Lamp & C Page 1 of 7
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationEasy Cover. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 944 Easy Cover Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 00-3-94 www.aeroindustries.com Indianapolis,
More informationUniversal Storage - Drawer and Overfile Stack Units
Universal Storage - Drawer and Overfile Stack Units Overfile Stack If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate
More informationJEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market
1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter
More informationRollstar Shade Installation Instructions
Rollstar Shade Installation Instructions All Lifting Systems Inside or Outside Mount Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the
More informationInstallation Instructions Studio Makeup Station
Installation Instructions Studio Makeup Station 30" and 36" Models 5-light 30" Studio Makeup Station 8-light 30" Studio Makeup Station 6-light 36" Studio Makeup Station 9-light 36" Studio Makeup Station
More informationINSTALLATION & OWNER S MANUAL
Rev. C p. 1 of 21 INSTALLATION & OWNER S MANUAL F5205 HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when
More informationWoda-Sci System Installation Parts Set
Installation Manual Woda-Sci System Installation Parts Set 5/32 x 3 ½ Drill Bit - 5 Connector Body - 7 3/8 Locking Nut - 8 3/16 x 1 ¼ Concrete Anchors- 4 Mounting Screws - 3 Stainless Steel Hanger - 9
More informationCetra Assembly Instructions
99877 Revision F- Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service. 0 Kimball International, Inc. T 800.8.88 F 8.8.800
More informationDraper Platform Adaptation Bundle
Draper Platform Adaptation Bundle 7050-Series Self-Propelled Forage Harvester 900D-Series Draper Platform RC042050 Operator s Manual Includes installation, operating, adjustment, technical, repair parts
More informationInstallation Instructions Table of Contents
Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft
More informationCetra. Ceiling Power Entry Installation (AEC1, AEC14, or AEC16)
Figure A Power Pole Top Cap Trim Plate L Bracket (Long leg attached to top of panel) Ceiling Installation (AEC, AEC, or AEC) Recommended Tools Variable Speed Drill with Torque Option Pop Rivets Riveting
More informationSYSTIMAX 360 FTP Evolve Panel Instructions
Instruction Sheet 860509975 SYSTIMAX Solutions SYSTIMAX 360 FTP Evolve Instructions General The SYSTIMAX 360 Evolve modular foiled twisted pair (FTP) patch panel is a highly flexible 24- or 48-port, front
More informationAnthro Mobile Device Charging Carts and Cabinets Owners Manual
Anthro Mobile Device Charging Carts and Cabinets Owners Manual TECHNOLOGY FURNITURE Hello! Thank you for choosing Anthro. Anthro's Tablet Charging Carts and Cabinets are designed to automatically charge
More informationInstallation Instructions Supertop NX Twill
Installation Instructions Supertop NX Twill Vehicle Application: Jeep Wrangler Unlimited 2007-current Part Number 54823 Installation Tips Before you begin installing your new Supertop NX Twill, please
More informationTable of Contents Next FLO-SAFE Manifold System Pre-Installation Kit Matrx Toll-Free: Technical Support: Fax: Rev.
FLO-SAFE Manifold System Pre-Installation Kit Instruction Manual Matrx 145 Mid County Drive Orchard Park, New York 14127 716-662-6650 Toll-Free: 800-847-1000 Technical Support: 888-279-1260 Fax: 716-662-8440
More informationSpectra C3 Light Bar Installation Instructions
Light Bar Hardware Tools Required Universal Clamp Inserts 1.9, 2 3/8 - OD 5 Amp Fuse 1.25 Hole Saw Philips Screw Driver 7/64 Drill Bit Fish Tape Countersink Pencil Pigtail Wiring Harness Clamp Washer Wire
More informationSYSTIMAX 360 ipatch InstaPATCH Fiber Shelf Instructions
Issue 6, June 2014 SYSTIMAX 360 ipatch InstaPATCH Fiber Shelf Instructions General The SYSTIMAX 360 ipatch InstaPATCH fiber shelf is a SYSTIMAX approved product and is available in a sliding configuration
More informationWAVETRAX USER MANUAL
WAVETRAX USER MANUAL 107719-2A0 WAVETRAX User Manual Document Number 107719-1A0 Copyright 2001, Telect, Inc., All Rights Reserved. Telect and Connecting the Future are registered trademarks of Telect,
More informationSolar Dolly. Assembly Manual
Solar Dolly Assembly Manual Components and Hardware 5 5 4 4 7 7 6. 1. Battery Box 2. Stabilizer Legs (R,L) 3. Uprights (R, L) 4. Adjustable Angle Brackets 5. Panel Brackets (R,L) 6. Controller Mounting
More informationMizer Single Pump and Starter Box
Mizer Single Pump and Starter Box Table of Contents Line Diagram... 2 Overview... 3 Booster Pump Specifications... 3 Water... 3 Electrical... 3 Models... 3 Mounting... 4 Electrical... 6 Motor Rotation...
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE
More informationSERVICE INSTRUCTIONS KEATING keatingofchicago.com
SERVICE INSTRUCTIONS 1-800-KEATING keatingofchicago.com FIELD REPLACEMENT KIT - for replacing Flame Switch 037406 with External Spark Module Box Assembly For use on all 10x11 fryers, 14" Front Drain fryers
More informationSolar & Roller Shades
STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades Loop Control, Loop Control with Cassette/2 on 1 Headrail & Loop Control with Metal Valance Table of Contents Step 1 - Getting Started....3 Everything
More informationZIP LIGHT LED LUMINAIRE
LED LUMINAIRE INSTALLATION MANUAL Note: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the Canadian Electrical Code (CE) and for the United States follow
More informationBulletin 1494C Cable Operated Disconnect Switch Kit (600A) Installation Instructions (Cat 1494C- _ Series 2 : 600A)
Bulletin 494C Cable Operated Disconnect Switch Kit (600A) Installation Instructions (Cat 494C- _ Series : 600A) ATTENTION: To prevent electrical shock, disconnect from power source before installing or
More informationLine Lock Package, Mustang GT/GT500, 2007 PACKING LIST
PART #M25002 Line Lock Package, Mustang GT/GT500, 2007 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION
More informationLED IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationEasy/Tran TF STANDBY POWER FURNACE SWITCH TOOLS NEEDED FOR INSTALLATION. PARTS LIST for Easy / Tran TF FURNACE TRANSFER SWITCH
STANDBY POWER FURNACE SWITCH Easy/Tran TF Congratulations on your purchase of the Reliance Controls Easy/Tran TF furnace transfer switch. Reliance has been manufacturing transfer switches and equipment
More informationInstruction Sheet. Subject: Installations Instructions. Air Compressor Kits. Importan
MULTIPLEX 2100 FUTURE, SELLERSBURG, IN 47172 800-367-4233 WWW.MANITOWOCBEVERAGE.COM/US Instruction Sheet Subject: Installations Instructions Importan Read the following warnings before beginning an installation.
More informationINSTALLATION INSTRUCTIONS Mitsubishi Lancer Evolution VIII / IX Fuel Surge Tank Kit Document#
d INSTALLATION INSTRUCTIONS Mitsubishi Lancer Evolution VIII / IX Fuel Surge Tank Kit Document# 19-0077 Brie Tech Support: info@radiumauto.com CAUTION: Exercise extreme caution when working with the fuel
More informationInstallation Instructions Capacity 10,000 lbs. DP10 (200 Series Lift)
Installation Instructions Capacity 10,000 lbs. DP10 (200 Series Lift) IMPORTANT Reference ANSI/ALI ALIS, Safety Requirements for Installation and Service of Automotive Lifts before installing lift. OPERATING
More information626F Exit Device Trim Installation Instructions
626F Exit Device Trim Installation Instructions For use with all Yale 7000, 2100, 1800 and 1500 Series Exit Devices (Wood and Metal Doors) Attention Installer Any retrofit or other field modification to
More informationA B C D E F. Tools Required (supplied by others)
Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)
More informationInstalling Ignition Coil relay
Installing Ignition Coil relay Above is a schematic diagram of the coil relay modification. All it really does is, it uses the existing 12 Volt positive that normally powers the coils, to power a relay,
More informationInstallation Instructions Skylight FlexShades by Draper
Caution 1 Read entire procedure before installing. Keep instructions for future reference. 2 Tools needed for installation: Cordless drill/screwdriver, with flathead, phillips, and 1 /4" nut driver attachments
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationPlasma Dual Swing-Out (PDS Series) Wall Mount
INSTALLATION INSTRUCTIONS Plasma Dual Swing-Out ( Series) Wall Mount The wall mount is a rugged, versatile, and installer-friendly solution to unique display mounting requirements. In addition to providing
More informationHP Modular Cooling System 200/100 Options Installation Guide
HP Modular Cooling System 200/100 Options Installation Guide Abstract This document is intended for the person who installs racks and rack products, is qualified in performing installations, and trained
More informationA B C D E F. b.tools Required (supplied by others) 3/16" Drill Bit 3/8" Wrench Phillips Head Screwdriver
Page 1 of 13 5E.1 Parts List a. Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel with Motor Attached (B) (1) Rope Reel Cover (C) (1) Cover Drum (1) Cover
More informationInstallation Instructions Capacity 10,000 lbs. (100 Series Lift)
Installation Instructions Capacity 10,000 lbs. (100 Series Lift) IMPORTANT Reference ANSI/ALI ALIS, Safety Requirements for Installation and Service of Automotive Lifts before installing lift. OPERATING
More informationw w w. h d o n l i n e s h o p. d e LAYBACK LICENSE PLATE AND TURN SIGNAL RELOCATION KIT INSTALLATION GENERAL -J03892 REV Kit Number
-J0 REV. 00-0-0 LAYBACK LICENSE PLATE AND TURN SIGNAL RELOCATION KIT GENERAL Kit Number 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM S2000 AII 26324 Issue Date OCT 2004 PARTS LIST Headrest Speaker System P/N 08A54-S2A-100 3 Small wire ties 2 Headrest speakers 9
More informationHP10220 KIT. See application guide for proper fitment.
HP10220 KIT Dodge Dakota* (2WD/4WD) * 2005 All Dodge Dakotas 2006 - All Dodge Dakotas except Night Runner and R/T sub models 2007 - All Dodge Dakotas except SXT and TRX4 sub models 2008 - All Dodge Dakotas
More informationOwner s Manual Electric Swivel
12-225- 11/6/17 1 of 22 Owner s Manual Electric Swivel Onboard Systems International 13915 NW 3rd Court Vancouver, WA 98685 United States of America Cage Code: 1Y921 Toll Free Phone: (8) 275-883 Phone:
More informationInstallation Notes. PlayPorTT Kiosk Anti-Tip Safety Cable. (p/n )
May 2010 900410-001 Rev. 01 About This Document This document is intended for: Operators of TouchTunes PlayPorTT wireless game and music systems. TouchTunes Field Service, Customer Support, and Sales personnel.
More informationPLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION
INSTALLATION INSTRUCTIONS PART NUMBER: L0SXC000 DESCRIPTION: 09 ASCENT TRAILER HITCH PLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION SAFETY PRECAUTION: When installing Trailer Hitch,
More informationTrackstar Motorized Folding Shade Installation Instructions
Trackstar Motorized Folding Shade Installation Instructions Thank you for purchasing your new Trackstar folding shade. It has been custom-made from the highest quality materials to the dimensions you specified.
More information5830 Skylight, Solar Smart Retrofit Installation
Introduction The Solar Smart has a mounting bracket that allows the operator to rotate slightly to reduce wear and tear on the chain drive system for greater performance and reliability. Because of this
More informationINSTALLATION GUIDES OUTDOOR LIVING
S OUTDOOR LIVING TABLE OF CONTENTS 12 Volt 12 Watt DC Transformer Page 2 12 Volt 50 Watt DC Smart Transformer Page 3 12 Volt 50 Watt Smart Transformer Control Page 4-5 Waterproof Dimmer For 12W Transformer
More informationZoneEx Modular Wiring System
1 ZoneEx Modular Wiring System ZoneEx is an innovative modular wiring system which offers safer, easier, and efficient solution for electrical installation. The pre-assembled, plug & play Zone Boxes and
More informationTABLE OF CONTENTS SPECIFICATIONS 3 INSTALLATION 4. Direct Mount 4. Ducted Installations 5. Installing Plenum 5. Machine Mount Stand 5.
TABLE OF CONTENTS PAGE SPECIFICATIONS 3 INSTALLATION 4 Direct Mount 4 Ducted Installations 5 Installing Plenum 5 Machine Mount Stand 5 Ceiling Mount 6 Pedestal Stand 7 Drain Installation 7 Electrical 8
More information4-WHEEL CART ASSEMBLY INSTRUCTIONS Mission Oaks Blvd., Camarillo, CA Visit our Web site at
4-WHEEL CART ASSEMBLY INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 003 by Harbor Freight Tools. All rights reserved. No portion of
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket Display 2007-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9560) Kit Contents: Camera/Module/Bezel Assembly Chassis Harness with
More informationSALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT
= SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT INSTALLATION MANUAL: 2005-09 Mustang 4.6L 3V P/N: 10-8002-C12000B KIT P/N: 10-2903-B11511* Saleen Performance, Inc. 1225 East Maple Rd. Troy,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PART # 074ST17N22G Product: FRONT BUMPER Vehicle: FORD F250/350 SUPERDUTY 2011-2016 WARNING Read instructions completely before commencing fitment. Always use personal safety
More informationHow to remove and replace the Foonf/Fllo fabric
How to remove and replace the Foonf/Fllo fabric Remove Headrest Locate the Troubleshooting Tool behind the manual on the back of the car seat, as shown in Figure 1. Raise Headrest to highest position by
More informationMF-12A MF-12A OWNER S MANUAL MF-12A PINSPOTTER MACHINERY DIVISION
MF-12A MF-12A PINSPOTTER MF-12A MACHINERY DIVISION OWNER S MANUAL ELECTRICAL REQUIREMENTS Connect the MF-12A to a 60 amp power supply. (208-230 volts 60 cycle). The MF-12A uses 208 230 volt single phase.
More informationTop Down Rollstar Shade Installation Instructions
Top Down Rollstar Shade Installation Instructions Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the dimensions you specified. With proper
More informationSYSTIMAX 360 ipatch G2 Fiber Ultra High Density (UHD) Shelf, MPO Distribution Panel Instructions
Instruction Sheet 860564699 Issue 2, January 2014 SYSTIMAX Solutions SYSTIMAX 360 ipatch G2 Fiber Ultra High Density (UHD) Shelf, MPO Distribution Panel Instructions General The SYSTIMAX 360 fiber optic
More informationACL 780/781 Economy Combo Tester
ACL 780/781 Economy Combo Tester OPERATION MANUAL Meter is warranted for one year from the date of purchase on parts and labor. Calibration is recommended every twelve months. 840 W. 49 th Place Page 1
More informationOperation Manual Image
Operation Manual Image 82, 42, 22 4/14/03 Image 82 8 x 4ft lamps Manual on/off switching control Switches 2 lamps at a time Image 42 4 x 4ft lamps Manual on/off switching control Switches 2 lamps at a
More informationReplacement Top Hardware Installation Instructions
Replacement Top Hardware Installation Instructions Windshield Channel Installation 1. Position Windshield Channel onto vehicle as shown in Figure 1. 2. Once in position, secure Windshield Channel using
More informationINSTALLATION INSTRUCTIONS NEON RGB
LLI-NCC3.7W **DANGER: Prior to installation, disconnect power at the source.** Make sure you have all components listed below: Neon 24V Non-Diming Power Supply RGB Receiver/Decoder Mounting Clips or Extrusion
More information! DANGER Lb. Winch Mounting Instructions. Tools required: Before You Start. Assembly Instructions. General Information. Manual No.
500 Lb. Winch Mounting Instructions For 400/4400 NT/ST, 40/440 ST And 40/440 ST Manual No. 70-86M Before You Start! When you see this symbol, the subsequent instructions and warnings are serious - follow
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationBulletin 1494C Cable Operated Disconnect Switch Kit (400A) Installation Instructions (Cat 1494C- _ Series 2 : 400A)
Bulletin 494C Cable Operated Disconnect Switch Kit () Installation Instructions (Cat 494C- _ Series : ) ATTENTION: To prevent electrical shock, disconnect from power source before installing or servicing.
More informationTECHNICAL SPECIFICATIONS. CAPACITY per slot width 1ʺ 1.25ʺ 1.5ʺ HKPX2VC/A 2 modules devices HKPY2VC/A 3 modules devices
USER GUIDE Mobility MiX Cart HKPX2VC/A Mobility MiX Cart 30 HKPY2VC/A Mobility MiX Cart 45 TECHNICAL SPECIFICATIONS CAPACITY per slot width 1ʺ 1.25ʺ 1.5ʺ HKPX2VC/A 2 modules 30 24 20 devices HKPY2VC/A
More informationInstallation, Maintenance and Service Manual Power Cord
Installation, Maintenance and Service Manual Power Cord 45-081, REV. 8/14 1 of 8 Table Of Contents Section 1 Installation Procedure... 3 1.1 General...3 1.2 Sheave installation...4 1.3 Anchor installation...4
More informationQuick Start Guide Compact 22 LE ( s/n & up)
Quick Start Guide Compact 22 LE (920013 s/n 75000 & up) Step 1: Assemble Handlebar Step 2: Install Discharge Chute Step 3: Install Discharge Chute Crank Step 4: Check Function of Dual Handle Interlock
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Versa Note 999F3 4Z000 - Accent Lighting Kit. 999Q9 AY000 - Accessory Service Connector
More informationUniversal Splice Tray Installation Instructions
Universal Splice Tray Installation Instructions Table of Contents General Product Information... 1.0 Safety Precautions... 2.0 Package Contents... 3.0 Installing the Product... 4.0 Tower Mounting... 5.0
More informationClassic Light Bar Mustang
Classic Light Bar 2005-2012 Mustang Note: Read installation instructions before starting. Component List: 1 Light Bar Part #110000 1 Driver Side Bracket w/set Screw Part #115003 1 Passenger Side Bracket
More informationxtablet T7000 Vehicle Mount Kit
xtablet T7000 Vehicle Mount Kit Installation & Users Guide Last Updated: January 19, 2012 Find the latest updates in the Support section in the MobileDemand website at: www.ruggedtabletpc.com. Questions?
More informationINSTALLATION GUIDE PRISONER TRANSPORT LIGHTING. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE PRISONER TRANSPORT LIGHTING STRONG RELIABLE SECURE pro-gard.com 800.480.6680 THESE COMPONENTS ARE REQUI TO INSTALL THE PRO-GARD PRISONER TRANSPORT LIGHTING 3" Round LED Lighthead QTY=
More informationDo not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001
This chapter contains these topics: Safety Warnings, page 1 Box Contents, page 3 Installation Guidelines, page 6 Mounting the Switch, page 8 Installing the Power Cord Retainer, page 63 10/100 Port Connections,
More informationInstallation Instructions
01 Inspect : Inspect the box for obvious damage. Make sure the product box was delivered in proper condition and all the fragile labels were honored. If the box looks to be in bad shape; straps are broken,
More information2 4 L R I G I D L E D L E D S I M U L AT E D N E O N I N S TA L L AT I O N G U I D E MANUAL FOR 48 SYSTEM ADVANCE POWER SUPPLY ONLY!
R I G I D L E D L A S E R T M / L E O N L E D S I M U L AT E D N E O N T M 2 4 L I N S TA L L AT I O N G U I D E MANUAL FOR 48 SYSTEM ADVANCE POWER SUPPLY ONLY! 185-1976 Philips Advance 100W 24V LOW VOLTAGE
More informationHANDY GATE ASSEMBLY, INSTALLATION AND OPERATING INSTRUCTIONS
ASSEMBLY, INSTALLATION AND OPERATING INSTRUCTIONS BEFORE INSTALLING OR USING THE, REVIEW THE VEHICLE LOADING LIMITATIONS OUTLINED IN THE VEHICLE OWNER S MANUAL AND THE SAFETY COMPLIANCE CERTIFICATION LABEL
More informationFAX
INSTALLATION INSTRUCTIONS 6090 Air Suspension Kit (pat. pending) 1999-2006 Tahoe, Suburban, Avalanche, Yukon Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationTechnical Support (707)
Installation Instructions CONSOLE MEGASHIFTER Fits: 1982-1992 Camaro & Firebird w/automatic Transmission *except 1988-1992 Firebird Formula Model Catalog # 80692 WORK SAFELY! For maximum safety, perform
More informationipatch Ready Upgrade Kit for SYSTIMAX 360 Fiber Shelves Instructions
Instruction Sheet 860463090 Issue 3, December 2012 SYSTIMAX Solutions ipatch Ready Upgrade Kit for SYSTIMAX 360 Fiber Shelves Instructions General These instructions describe how to install ipatch Ready
More informationPROCEDURE STEPS: WARNING:
WI-FI ROUTER 1 DODGE NITRO, JEEP LIBERTY PROCEDURE STEPS: WARNING: Disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect
More informationand Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks present T-420 BOLT-ON GUSSET PART#5257
and Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks- 2004-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket
More informationElegance Electrician s Installation Guide
Elegance Electrician s Installation Guide CentraLite Systems, Inc. 6420 Wall St. Mobile, AL 36695 Phone: 877-466-5483 Fax: 251-607-9119 2003-2005 CentraLite Systems, Inc. Revised 10/20/2005 ELECTRICIAN
More information