Installation Instructions for SINGLE COLOR 24V LINEAR LED NEON
|
|
- Helena Walton
- 6 years ago
- Views:
Transcription
1 Installation Instructions for SINGLE COLOR 24V LINEAR LED NEON LLI-N2.9W Prior to installation, please confirm that you have the required system components listed below. LED Neon Flow Extrusions/Lens (Optional) Power Supplies 1
2 Please read and follow these steps before beginning the installation. These products may represent a potential shock or fire hazard if improperly installed or attached in any way. Products should be installed in accordance with these instructions, current electrical codes and/or the National Electric Code (NEC). Do not connect directly to high voltage power ( v)! To avoid electrical shock, disconnect or disable power at the source prior to installation or maintenance. To avoid electrical shock, use only 24v hardwire or plug in power supply. Factory warranty will be void if used otherwise. To avoid product failure, pair the correct voltage power supply to the correct voltage LED Neon Flow. LLI Architectural Lighting s LED Neon is suitable for outdoor use and damp locations (IP65). Do not use if there is any damage to the unit or to the power cord s insulation. Inspect periodically. Do not puncture, cut, shorten, or splice LED Neon. Consult factory for custom configurations. Do not secure LED Neon or it s power cord with staples, nails, or any other sharp objects that may damage the cords. Do not roll out LED Neon on rough surfaces and over sharp corners. Do not secure LED Neon with staples, nails, or any other sharp objects that may damage the PVC material. Ensure proper gauge wires are installed between Power Supplies, Controls & LED Neon lighting to avoid voltage drop. Ensure applicable wires are in compliance with local codes (In-wall rated, wet-location, high temperature, etc.). Maximum load for power supplies is 80%. ***If you have any questions or concerns about your installation, please call our Technical Specialists at *** 2
3 1 1/2 MAXIMUM BEND RADIUS 1 1/2 INCH DO NOT TWIST LED NEON FLOW DO NOT BEND LED NEON FLOW IN THIS WAY DO NOT BEND LED NEON FLOW IN THIS WAY 3
4 Prep LED Neon Flow for Installation STEP 1 STEP 2 Remove the LED Neon from it s package and un-roll the LEDs. Measure the location where the LED Neon will be placed. STEP 3 STEP 4 Fasten mounting clips/channel onto mounting surface using appropriate hardware (not included). Carefully press the LED Neon into the support channel or mounting clips until secure. NOTE: Maximum length for single run of 24vdc is 50ft. If powered from each end maximum run length can be extended to 100ft. NOTE: Do not install with bend radius smaller than 3.5 for LED Neon Flow. 4
5 STEP 5 STEP 6 Locate and route power feed wire back to power supply. Mount power supply in desired location and connect LED Neon to low voltage output of power supply. Connect power supply to 120vac line voltage and turn on LED Neon product. NOTE: Connect the positive wire from the power supply to the positive (+) wire on the LED Neon Flow. Connect the negative (-) wire from the power supply to the negative wire on the LED Neon Flow. Please make sure you always connect to the correct polarity. Each section is marked with a (+) for positive and a (-) for negative. If a section does not energize, you may need to check the connector or switch the wires. 5
6 Low Voltage Wire Gauge Chart 6
7 TYPICAL COLOR CHANGING CONNECTION DIAGRAM 7
INSTALLATION INSTRUCTIONS NEON RGB
LLI-NCC3.7W **DANGER: Prior to installation, disconnect power at the source.** Make sure you have all components listed below: Neon 24V Non-Diming Power Supply RGB Receiver/Decoder Mounting Clips or Extrusion
More informationInstallation Instructions for SINGLE COLOR 12V or 24V LINEAR LED
Installation Instructions for SINGLE COLOR 12V or 24V LINEAR LED LLI-L1.5W (T300) LLI-L2.2W (TSHL2835-300) LLI-L2.5W (TSHL2835-600-2.5W) LLI-3.5W (TSHL2835-480) LLI-L4.4W (TSHL2835-600) LLI-L5.9W (TUB5630-560)
More informationINSTALLATION INSTRUCTIONS SURFACE EXTRUSIONS WITH LED TAPE
LLI-XS-30D LLI-XS-60D LLI-XS-90D LLI-XS-ANG LLI-XS-AUR LLI-XS-DEP LLI-XS-DOM LLI-XS-ELT LLI-XS-FLX LLI-XS-GEN LLI-XS-GZR LLI-XS-ICN LLI-XS-SQR LLI-XS-THN LLI-XS-WID LLI-XS-ZEN **DANGER: Prior to installation,
More informationINSTALLATION INSTRUCTIONS WHITE / SINGLE COLOR 24V LED TAPE
LLI-L1.5W LLI-L2.2W LLI-L2.5W LLI-L3.5W LLI-L4.4W LLI-LHE3.5W LLI-LHE4.4W LLI-LHE5.9W LLI-LTP2.5W LLI-LTP5.0W LLI-LSE3.0W LLI-LWF5.5W LLI-LC4.4W **DANGER: Prior to installation, disconnect power at the
More informationINSTALLATION INSTRUCTIONS RECESSED EXTRUSIONS WITH LED TAPE
LLI-XR-CRV LLI-XR-ELF LLI-XR-IFL LLI-XR-IGR LLI-XR-SQF LLI-XR-THF **DANGER: Prior to installation, disconnect power at the source.** Make sure you have all components listed below: LED tape 24VDC Power
More informationInstallation Instructions for GRIPPER CONNECTOR
Installation Instructions for GRIPPER CONNECTOR LLI-GC-LL-RGB LLI-GC-LL-RGBW (12mm only) LLI-GC-LL-SC LLI-GC-LL-VW LLI-GC-LW-RGB LLI-GC-LW-RGBW (12mm only) LLI-GC-LW-SC LLI-GC-LW-VW Prior to installation,
More informationchannel damage the internal components and the weight may break the internal wiring or flexible strip.
YOU MAY NEED End cap Power adaptor Connector pin Splicing pin Connector Silicone glue Pliers Power converter Converter + surge protector Heat shrink Aluminium channel Heat gun NT cutter IMPORTANT NOTES
More informationLEDneon flex. Features & Benefits DOT-FREE ILLUMINATION
DOT-FREE ILLUMINATION Features & Benefits Viable alternative to glass neon 220V with power converter 12V DC with constant voltage driver Seamless, dot-free illumination Up to 80% more energy efficient
More informationInstallation Instructions: HYPERION R-Lite SYSTEM
Installation Instructions: HYPERION R-Lite SYSTEM READ THIS MANUAL BEFORE PROCEEDING WITH THE INSTALLATION. FAILURE TO FOLLOW THE INSTALLATION INSTRUCTIONS WILL VOID YOUR WARRANTY! INSTALLATION TIPS Read
More informationWARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS
WARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS DO NOT solder connectors as this will prohibit the adapters circuit switch to move freely from circuit to circuit. Nordic Aluminium track adapters and accessories
More informationNOVA FLEX FLEXIBLE LED SOLUTIONS
DESIGN SERIES / ARCHITECTURAL LIGHTING HighCRI (90) LED ribbon light in output ranges for every application. Architecturalgrade lighting that ensures proper execution of design intentions. 50,000 DESIGN
More informationNANOTUNE. Installation Manual
Installation Manual WARNING: DO NOT ATTEMPT TO INSTALL OR USE THE NANOLUME FIXTURE WITHOUT READING THE INSTALLATION INSTRUCTIONS AND SAFETY LABELS COMPLETELY. Failure to adhere to these instructions could
More informationDURATAPE TM RGB IP66 OUTDOOR
Key Features Flexible flat conductor strip with High Output Red 625nm, Green: 520nm, Blue: 465nm LEDs, RGB colors Ideal for exterior cove, under-counter/cabinet, lighting accents Complete with encased
More informationSURFACE/CEILING & SUSPENDED MOUNT INSTALLATION
SURFE/CEILING & SUSPENDED MOUNT INSTALLATION E477827 E477827 APPLICATION NL luminaires are designed for use indoors, outdoors, wet locations, areas containing moisture, dirt, corrosion, vibration and rough
More informationWARNING. Tools: 1. Wire Strippers 2. Screw Driver or Rivet Gun 3. Tape Measure 4. Drill. Components: AWG (0.82mm) Wire-UL Approved
Tools: 1. Wire Strippers 2. Screw Driver or Rivet Gun 3. Tape Measure 4. Drill Components: 1. 1 AWG (0.2mm) Wire-UL Approved *Under certain conditions, a heavier gauge wire may be necessary. 2. General
More informationInstallation Instructions Table of Contents
Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft
More informationTRAC-Station BT Installation Instructions
TRAC-Station BT Installation Instructions P/N 10103024P1 November 2011 2011 UTC Fire & Security. All rights reserved. Introduction This is the Supra TRAC-Station BT Installation Instructions. Read these
More informationSloanLED THINLED. Constant Current. Installation Guide
SloanLED THINLED Constant Current Installation Guide Product covered in this guide: ThinLED CC: Part Number Description 701228-18-A Amber ThinLED Constant Current 701228-18-B Blue ThinLED Constant Current
More informationLED NEON FLEX INSTALLATI ON GUI DE
LED NEON FLEX INSTALLATI ON GUI DE F I R E F L Y L I G H T I N G. C O M. A U WHAT IS LED NEON FLEX? THE MOST VERSATILE AND SIMPLE LIGHTING SYSTEM YOU WILL EVER USE LED Neon Flex is a green friendly, safe,
More informationBase Power Infeed Installation for Training Tables with Modular Table Power System
Base Power Infeed Installation for Training Tables with Modular Table Power System Topic Table of Contents General Safety Warnings Base Power Infeed Usage Electrical Circuits Base Power Infeed - 0 Amp
More informationWARNING/AVERTISSEMENT. Coupez l alimentation électrique à la boîte de fusibles ou au disjoncteur avant servicing or installing product.
Tetra Contour LS LED Lighting System GEXNLBL-1, GEXNLGL-1, GEXNLRD-1, GEXNL65-1, GEXNL32-1 Installation Guide 24 Volt BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT
More informationInstallation Instructions: ACCENT SYSTEM
Installation Instructions: ACCENT SYSTEM READ THIS MANUAL BEFORE PROCEEDING WITH THE INSTALLATION. FAILURE TO FOLLOW THE INSTALLATION INSTRUCTIONS WILL VOID YOUR WARRANTY! INSTALLATION TIPS Read this entire
More informationInstallation Instructions: ACCENT HIGH OUTPUT SYSTEM
Installation Instructions: ACCENT HIGH OUTPUT SYSTEM READ THIS MANUAL BEFORE PROCEEDING WITH THE INSTALLATION. FAILURE TO FOLLOW THE INSTALLATION INSTRUCTIONS WILL VOID YOUR WARRANTY! INSTALLATION TIPS
More informationSource: 209.2LM per foot, 2.7W per foot
ILLUMINATING THE FUTURE...SINCE 1989 Type Project Catalog No. Lamp/Wattage NUTP51-W100LED9 Series 24V Continuous Hy-Brite LED Tape Light Source: 209.2LM per foot, 2.7W per foot Dimensions Max 32FT. PRODUCT
More informationDry Contact Closure Interface
Dry Contact Closure Interface Overview LuXout Shades Dry Contact Closure Contact closure interfaces allows integration of the Automation systems throughout the house. The contact closure interface communicates
More informationNOTE: The orientation of the mounting brackets are critical. (See Figure 4)
Page 1 of 5 11.25.13 Lamping Specifications 10138 I-wall 2 120v, One, F14WT5/Mini Bi-Pin 277v, One, F14WT5/Mini Bi-Pin 10139 I-wall 3 120v, One, F21WT5/Mini Bi-Pin, 277v, One, F21WT5/Mini Bi-Pin 10140
More informationELECTRICAL SAFETY. Safety Training For The Non-Qualified
ELECTRICAL SAFETY Safety Training For The Non-Qualified LANGUAGE OF ELECTRICITY Electricity: Negatively Charged Particles Moving Over A Conductor Current: Movement Of Electrons Along A Conductor Ground
More informationDURATAPE TM HO INDOOR RGB+W
PROJECT MODEL(S) TYPE High Output RGB+W Tapelight High output indoor RGB and RGB+W LED Tapelight strip emits sharp, color changing effects in indoor niche, cove and architectural decorative applications.
More informationMOUNTING SYSTEMS SPECIFICATIONS
MOUNTING SYSTEMS SPECIFICATIONS GENERAL Mounting Systems shall allow Track Systems to be fastened to or from various surfaces in a wide range of safe and approved methods. Mounting Systems shall have a
More informationHPNLS-HO. Installation Manual
Installation Manual WARNING: Do not lift fixture by cables. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/or putting undue pressure
More informationRibbonFlex Pro LED Accent Lighting White LED Tape Light. Welcome to RibbonFlex Pro LED Tape Lighting. Notes:
RibbonFlex Pro LED Accent Lighting White LED Tape Light 30 White LEDs per meter (9 LEDs per foot) Model # RF3528030 rev 01.14 Welcome to RibbonFlex Pro LED Tape Lighting Ultra thin and flexible, RibbonFlex
More informationNANO MIX. Installation Manual
Installation Manual WARNING: DO NOT ATTEMPT TO INSTALL OR USE THE NANOLUME FIXTURE WITHOUT READING THE INSTALLATION INSTRUCTIONS AND SAFETY LABELS COMPLETELY. Failure to adhere to these instructions could
More informationNUTP7-LED (Amber Finish) NUTP7-WLED (White Finish) 24V LED Tape Light Roll. Source: 24W Watts Per Foot CRI. 24V LED Tape Light Roll
ILLUMINATING THE FUTURE...SINCE 1989 NUTP7-LED (Amber Finish) NUTP7-WLED (White Finish) 24V LED Tape Light Roll PRODUCT DESCRIPTION Nora s very low profile, energy efficient LED tape is only 7/16" wide
More informationHPFB. Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES.
Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/ or putting undue pressure
More informationAUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS
AUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS The original TOMMY GATE hydraulic lift Assembling the Auxiliary Battery Box 1. Remove the cover from the auxiliary battery box by removing the two nuts and
More informationPDX and PX Retrofit Series
UNIQUE LIGHTING SOLUTIONS PDX and PX Retrofit Series PDX1-1-12-XX PX1-1-12-X-X-XX-65 RETROFIT INSTALLATION GUIDE PDX and PX Series Retrofit WARNING -Retrofit installation must only be performed by a licensed
More informationSunwize Power Ready Express Quick Start
Document # 310002 Sunwize Power Ready Express Quick Start The purpose of this guide is to assist you in setting up your system quickly and efficiently. Important! Prior to field installation Determine
More informationNUTP7-16LED 24V 16' Damp Label Standard LED Tape Light Roll Source: 24W Watts Per Foot
NUTP7-16LED 24V 16' Damp Label Standard LED Tape Light Roll Source: 24W - 1.5 Watts Per Foot PRODUCT DESCRIPTION LED Tape Light is a perfect solution for your LED linear lighting needs. This energy efficient
More informationNuheat WEATHER-READY HEAT TRACE PIPE FREEZE PROTECTION SYSTEM. Self-Regulating Heating Cable Installation Guide. UV Resistant Polyolefin Outer Jacket
Nuheat WEATHER-READY HEAT TRACE PIPE FREEZE PROTECTION SYSTEM Self-Regulating Heating Cable Installation Guide Tinned Copper Braid UV Resistant Polyolefin Outer Jacket 16 AWG Bus Wire Polyolefin Inner
More informationAssembly Instructions Retrofitting
Assembly Instructions Retrofitting These instructions are for replacing existing lighting fixtures or systems with our new, higher efficiency TLS, drivers and controls. www.tls-lumisign.com 514-858-6556
More informationNICHE-HV. Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES.
Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/ or putting undue pressure
More informationInstallation Instruction
T F W 604.549.9379 604.549.9555 fluxwerx.com Installation Instruction DRIVER ENCLOSURE Ceiling Type Version Grid Battery Pack GRID MOUNT INSTALL OPTIONS OPTION 1: Standard Vertical Grid drivers can be
More informationDURATAPE TM RGB IP66 OUTDOOR
Key Features Flexible flat conductor strip with High Output Red 625nm, Green: 520nm, Blue: 465nm LEDs, RGB colors Ideal for exterior cove, under-counter/cabinet, lighting accents Complete with encased
More informationNUTP1-16LED 24V 16' Standard LED Tape Light Roll
NUTP1-16LED 24V 16' Standard LED Tape Light Roll Source: 24W LEDs PRODUCT DESCRIPTION LED Tape Light is a perfect solution for your LED linear lighting needs. This energy efficient and very low profile
More informationInitiate WARNING. Illustration 1. Panel Connection Guidelines:
Failure to install product as instructed, use of hardware other than that which is provided with the product, or failure to comply with all instructions can result in product failure and/or personal injury
More informationDURATAPE TM HO INDOOR RGB+W
PROJECT MODEL(S) TYPE DURATAPE TM HO High Output RGB+W Tapelight High output indoor RGB and RGB+W LED Tapelight strip emits sharp, color changing effects in indoor niche, cove and architectural decorative
More informationThe LED Driver Expert
Power Unit Installation Instructions 1) Installation of the series power unit requires the proper connection of both the AC wires to the AC facility power, and the DC wires to the LED lighting system.
More informationPRODUCT INFORMATION BULLETIN
724-283-4681 724-283-5939 (fax) PRODUCT INFORMATION BULLETIN DESCRIPTION The, Model 10-7100 is one in a series of critical speed switches that monitor speed and detect motion in all types of machinery
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
LIGHTPATH SERIES LOW LEVEL FULLY RECESSED LED EMERGENCY LIGHT 1. 2. 3. 4. 5. 6. 7. 8. INSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always
More informationArktite Heavy Duty Circuit Breaking Plugs and Receptacles Industrial Heavy Duty Non-Hazardous Areas
1P Arktite Heavy Duty Circuit Breaking s and s Industrial Heavy Duty Non-Hazardous Areas Application: Arktite circuit breaking plugs and receptacles are used: to supply power to portable electrically operated
More informationInstallation Instructions Central Battery Units
Phone: 605.542.4444 concealite.com! Installation Instructions s Please Save These Instructions Important Safeguards Read and Follow All Safety Instructions When using electrical equipment, basic safety
More informationFlex Tube. User guide
Flex Tube User guide CONTENTS INTRODUCTION...2 Welcome 2 Safety 2 INSTALLATION...3 Flex Tube orientation 3 Bending a Flex Tube 4 Cutting a Flex Tube 4 Connection and mounting kits 5 Feed cable kit 5 End
More information50% 5 YEAR. Specification Sheet: LED Flex-Lite. The Energy Efficient LED Solution PRODUCT BENEFITS WARRANTY APPLICATIONS
The Energy Efficient LED Solution For accent lighting and various signage applications, s Flex-Lite offers an innovative and versatile LED alternative to neon. Flex-Lite encases white-light or primary-color
More informationNUTP1-16LED 24V 16' Standard LED Tape Light Roll Source: 24W LEDs
NUTP1-16LED 24V 16' Standard LED Tape Light Roll Source: 24W LEDs PRODUCT DESCRIPTION LED Tape Light is a perfect solution for your LED linear lighting needs. This energy efficient and very low profile
More informationArktite Heavy Duty Circuit Breaking Plugs and Receptacles
1P Arktite Heavy Duty Circuit Breaking s and Receptacles Industrial Heavy Duty Non-Hazardous Areas Application: Arktite circuit breaking plugs and receptacles are used: to supply power to portable electrically
More informationCord Operated Curtain Track Systems
Cord Operated Curtain Track Systems Application Chart Specification Weight Range Applications Single Stack Pair Stack Multiple Stack Asymetric Profile Profile Number Dimensions in mm Gliding Channel (mm)
More information650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior
More informationDURATAPE TM HO OUTDOOR RGB+W
PROJECT MODEL(S) TYPE High Output RGB+W Tapelight High output outdoor RGB LED Tapelight strip emits sharp, color changing effects in outdoor niche, cove and architectural decorative applications. Key Features
More informationThis is one of our EZ series brackets, which
R O A D M A S T E R, I N C. This is one of our EZ series brackets, which allows the visible front portion of the bracket to be easily removed from the front of the vehicle (Fig.A and Fig.B). The bracket
More informationINSTALLATION INSTRUCTION W Track Recessed 120V Flangeless
W Track Recessed 120V Flangeless WT4-RTL, WT8-RTL, WT12-RTL SAFETY INSTRUCTION Read all of these instructions before installing the track system. Turn off power at main switch before installing or modifying
More informationSource: 81.68LM per foot, 1.3 W per foot
ILLUMINATING THE FUTURE...SINCE 1989 Type Project Catalog No. Lamp/Wattage NUTP71-W100LED9 Series 24V Continuous Standard LED Tape Light Source: 81.68LM per foot, 1.3 W per foot Dimensions PRODUCT DESCRIPTION
More informationTSUBAKI FLEXIBLE SMOOTH
WHITE LEDS DESCRIPTION Tsubaki Flexible Smooth products provide highly flexible lighting strands for smooth and seamless direct view applications such as lighting and outlining of architectural features.
More informationTusk UTV Horn & Signal Kit Installation Instructions
Tusk UTV Horn & Signal Kit Installation Instructions The Tusk UTV signal kit is designed to be a simple way to provide front and rear turn signals, license plate mount with light, horn, and rearview mirrors
More informationR O A D M A S T E R, I N C.
R O A D M A S T E R, I N C. 6 13 11 MOUNTING BRACKET KIT Cable Tab 14 12 7 15 9 Cable Tab 2 8 10 ITEM QTY NAME MATERIAL 1... 4...1/2 x 1 3/4 BOLT... 350096-00 2... 2...1/2 x 5 1/2 BOLT... 350108-00 3...
More informationINSTALLATION & OPERATION MANUAL
EUKT05-RGBWW60 RGB + Warm White LED Strip Lighting System INSTALLATION & OPERATION MANUAL What s in the box? XC3-40500-RF RGB+W LED Controller w/ RF Remote Control EULSP0260-5.0 RGB+WW LED Strip Lighting
More information2. MEASURE VEHICLE HEIGHT. (b) Measure the vehicle height. Measurement points: C: Ground clearance of front wheel center
ADJUSTMENT If the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order
More informationDURATAPE TM RGBW IP66 OUTDOOR
Key Features Flexible flat conductor strip with High Output Red 625nm, Green: 520nm, Blue: 465nm LEDs, RGB colors can be used together with 3000ºK White LED to create different tone of White or soften
More informationPart Number Revision NC, September High Temperature Velocity and Acceleration Sensor Operation and Maintenance Manual
Part Number 168779-01 Revision NC, September 2004 350900 High Temperature Velocity and Acceleration Sensor Operation and Maintenance Manual 350900 High Temperature Velocity and Acceleration Sensor Operation
More informationInstallation Instructions MX-5 Dual Air Horns
440 Rutherford St. P.O. Box 847 Goleta, CA 93117 1-800-667-7872 FAX 805-692-2525 www.mossmotors.com Tools required: Phillips screwdriver, 8mm, 10mm and 21mm sockets, 8mm and 10mm combination wrenches,
More informationACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS
II 1400-10 ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS Features: Up to 1.95 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit Protection Standby Battery
More informationPlexineon Installation Manual
Plexineon Installation Manual ilight Technologies, Inc. 118 South Clinton, Suite 370 Chicago, IL. 60661, USA Tel: 312.876.8630 Fax: 312.876.8631 support@ilight-tech.com www.ilight-tech.com www.ilight-tech.com
More informationCV41. Vehicle Mounting Kit. Reference Guide
CV41 Vehicle Mounting Kit Reference Guide CV41 Vehicle Mounting Kit Reference Guide........... 3 Secure the Smart Dock to a Vehicle.................... 3 Supply Power to the Smart Dock......................
More informationLNT-65RGBW 3.4W IP67/IP68 COLOR-CHANGING LED STRIP
SPECIFICATION SHEET JOB NAME: LOCATION: QUOTE/REF#: LNT65RGBW is a high performance flexible LED fixture designed as a neon replacement. Suitable for indoor and outdoor applications, the LNT65RGBW can
More informationNUTP4-LED/4 12V 4" Standard LED Tape Light Section Source: 0.5W LEDs
NUTP4-LED/4 12V Standard LED Tape Light Section Source: 0.5W LEDs PRODUCT DESCRIPTION LED Tape Light is a perfect solution for your LED linear lighting needs. This energy efficient and very low profile
More informationINSTRUCTIONS. Power Panel. Installation Instructions
Overview LuXout Shade 18 Output - For use with LuXout Shades NOTICE: This power supply is built-in fan on/off control circuit. Fan automatically works according to working temperature. SHOCK HAZARD Risk
More informationSAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be
More informationTubeTrace Tubing Bundles
for Custom CEMS and Analytical Umbilicals English Units Receiving, Storing and Handling... 1. Inspect materials for damage incurred during shipping. Report damages to carrier for settlement. 2. Identify
More informationLINEARlight FLEX Diffuse 400 LFD400T / LFD400MT / LFD400S / LFD400MS
www.osram.us/flexlighting LINEARlight FLEX Diffuse 400 LFD400T / LFD400MT / LFD400S / LFD400MS Key Features & Benefits Saturated, homogeneous linear LED modules with the look of neon Flexible and field
More informationKompensator External Low Voltage Heating Cable System
External Low Voltage Heating Cable System LOW VOLTAGE Installation Instructions General Information Kit Contents Qty Description 1 heating cable at pre-determined length Table of Contents General Information........................
More informationFINA SUSPENDED INSTALLATION INSTRUCTIONS
FINA SUSPENDED INSTALLATION INSTRUCTIONS 3 AC Cable Mounting (AC3) Installation... 2-4 AC Cable to Hub Mounting (AH4) Installation... 5-7 Pendant Pipe Mounting Installation... 8-9 Canopy Detail... 10-11
More informationRecommended Tools: Phillips Screwdriver, Flat Blade Screwdriver, 13mm and 10mm Wrench, 5/16 nut driver,
UPS-ST-120 UPSPro Outdoor UPS System Wireless Base Stations and Client Devices Surveillance Cameras Mission Critical Backup Power Remote Sensors Congratulations! on your purchase of the UPSPro Outdoor
More informationTAG-DR Series. Indoor or Outdoor LED Driver Box - TAG LED Flood Solutions. Specifications. Overall Dimensions For Reference Only TAG-DR
Catalog Number: Approvals: TAG-DR Series Box Driver Voltage Options Finish Type Wattage Date: Page 1 of 6 Overall Dimensions For Reference Only TAG-DR * Indoor Box 3.1" (7.8 cm) 9.1" (23.1 cm) 8.9 (22.7
More informationLED estrip. Linear Lighting. Features. Specifications. Applications. Colour Specifications. Product Codes
Linear Lighting LED estrip LED estrip is our most versatile linear lighting product. Now with 3014 type LEDs, LED estrip is brighter and better than ever! DIMMABLE Features 40,000 hours life Safe low voltage
More informationR O A D M A S T E R, I N C.
R O A D M A S T E R, I N C. 8 MOUNTING BRACKET KIT 4 7 6 ITEM QTY NAME MATERIAL 1...2...1/2 x 4 1/2 BOLT...350106-00 2...2...1/2 HEX NUT...350258-00 3...2...1/2 LOCK WASHER...350309-00 4...2...#10 x 3/4
More informationDL-FLEX (-UP, -UP-HO, -UP-ULTRA)
-HO -ULTRA DESCRIPTION DL-FLEX series is a unique commercial grade modular lighting system featuring 3 levels of light output with a wide range of accessories and a variety of control options. This unique
More informationSolstice Electric Fryers SE Series Service Manual
Solstice Electric Fryers SE Series Service Manual L22-330 R1 (10/12) Notice In the event of problems or questions about your order, contact the Pitco Frialator factory at (603) 225-6684. In the event of
More information650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior
More informationAcme Conduit Entry. String Combiner/Pass-Through. FOR PHOTOVOLTAIC INSTALLATION Installation Manual
Acme Conduit Entry String Combiner/Pass-Through FOR PHOTOVOLTAIC INSTALLATION Installation Manual Table of Contents Important Safety Instructions -----------------------------------------------------------------------------------------------------------
More informationGeneral safety and installation information.
Read these instructions before connecting and using your PowerBright Pure Sine Power Inverters. Failure in observing this warning may result in injury to persons and damage to equipment. General safety
More informationInstallation Guide for EcoBrite EndLite LED Light Fixtures
Installation Guide for EcoBrite EndLite LED Light Fixtures BEFORE YOU BEGIN INSTALLATION Read these instructions carefully. Failure to follow these instructions will invalidate the warranty on this product.
More informationPower Connection Kit Installation Instructions. Terminator DP-M for use with TEK and HTEK series constant watt heating cables
Power Connection Kit Installation Instructions Terminator DP-M for use with TEK and HTEK series constant watt heating cables For Power Connection (1 Cable), In-Line Splice Connection, or End Termination
More informationFIXTURES - FLEXIBLE (Q - CAP) LENS ENC/CL ENC/CL S1 S2 S3 S4 P1 P2 P3 P4 2. Pass through
BOXA-RGB FIXTURES - FLEXIBLE (Q - CAP) COMPLIANT BOXA-RGB Voltage: 4 VDC Wattage:.8 W/Ft WSC DRY Per Channel RLC WET 5.3 W/Ft MC Total Load CCT OUTPUT LENS RGB SO ENC/CL RGB SO ENC/CL END CAPS (NO FEED)
More informationCustom LitePad Handling & Mounting Guide
Custom LitePad Handling & Mounting Guide Low profile light emitting panel for backlighting or area lighting, available in standard or custom sizes and fixed white, tunable white or RGB configurations,
More informationDURATAPE TM RGBW IP20 INDOOR
e Static Indoor Key Features Flexible flat conductor strip with High Output Red 625nm, Green: 520nm, Blue: 465nm LEDs, RGB colors can be used together with White LED to create different tone of White or
More informationDURATAPE TM RGB IP20 INDOOR
e Static Indoor Key Features Flexible flat conductor strip with High Output Red 625nm, Green: 520nm, Blue: 465nm LEDs, RGB colors can be used together with White LED to create different tone of White or
More informationInstallation Instructions & Users Manual IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Crystal Recessed Edge- lit LED Exit Signs Series CRRBB & CRRAC Battery Backup & AC Models 01.18.06 Installation Instructions & Users Manual IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
More informationP Original Series Cargo Van Lift Mounting Instructions Fullsize Ford Van present. Preparing the Gate
Fullsize Ford Van- 1992-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting kit (Figure 1 and Table 1). S-400-40 STRAP VAN MOUNTING EAR BENT BRACKET
More informationLED STRIP LIGHTING KIT EUKT04 WW30
LED STRIP LIGHTING KIT EUKT04 WW30 This kit comes complete with everything you will need to light up your project. It includes a deluxe LED dimmer controller, a mated AC/DC power supply, 16 4 of LED strip
More informationR O A D M A S T E R, I N C.
R O A D M A S T E R, I N C. 16 15 9 11 8 5 ITEM QTY NAME MATERIAL 1...2...1/2 x 1 3/4 BOLT...350096-00 2...2...1/2 x 1 1/2 BOLT...350095-00 3...4...1/2 LOCK WASHER...350309-00 4...2...1/2 HEX NUT...350258-00
More informationINSTALLATION GUIDE AND USER MANUAL
Electric Vehicle Charging Station INSTALLATION GUIDE AND USER MANUAL SAE J1772 AC Level 2 EVSE Model: 30A EVoCharge EVSE Wall Mount P/N: EV072-300-001A Version 2.0 IMPORTANT Read this manual thoroughly
More information