ILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT
|
|
- Chrystal Hubbard
- 5 years ago
- Views:
Transcription
1 082114EC ILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT Beghelli Canada th Avenue Markham, Ontario L3R 4R3 Canada P: (905) F: (905) Beghelli USA 3250 Corporate Way Miramar, Florida USA P: / P: F: Beghelli Mexico Av El Marques No. 70, Interior Mpio. El Marquez Queretano, QRO. Mexico P: / F:
2 INSTALLATION INSTRUCTION ILLUMINA BS100 FLUORESCENT T5, T5HO & T8 MODEL 120V to 277V INPUT HT & SA 2FT & 4FT LENGTH *Other volatages available contact factory LAMP SOCKET / HOLDER LENS CLIPS 2FT=4 CLIPS 4FT=8 CLIPS FIXTURE BODY CONDUIT KNOCKOUT (BOTH ENDS) LAMPS (NOT SUPPLIED) REFLECTOR LENS / DIFFUSER SERIES: OPERATION: INPUT: LENGTH EACH MODEL NUMBER CONSISTS OF THE FOLLOWING: SERIES / OPERATION / INPUT / SIZE / LAMP & BALLAST BS100 HT & SA 120V TO 277V INPUT 2FT LAMPS: T5 T5HO T8 LENGTH 4FT 1X14 1X24 1X17 2X28 2X24 2X17 LAMPS: T5 T5HO T8 1X28 1X54 1X32 2X28 2X54 2X32
3 TYPICAL INSTALLATION IMPORTANT SAFEGUARDS No user serviceable parts. Refer service to a qualified service technician. Read instructions prior to installing and/or operating this device. Installation should be performed by a licensed electrician/installer in accordance with local codes. When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. 1. Do not let power cords touch hot surfaces. 2. Do not mount near gas or electric heaters. 3. Always mount equipment in a location that is not subjected to tampering by unauthorized personnel. 4. The use of accessory equipment not recommended by Beghelli, may cause an unsafe condition, and will void the warranty. 5. Do not use this equipment other than its intended purpose. 6. Servicing of this equipment should be performed by qualified service personnel. FIRST MAKE SURE POWER IS TURNED OFF! 1. Remove diffuser / lens. 2. Remove the reflector and mounting hardware bag. 3. Install the weatherproof electrical connector if needed. (not supplied by Beghelli) 4. Securely mount the fixture with the hardware provided. 5. Prepare fixture for wiring / hanging reflector from internal clips. 6. Connect AC supply and ground as labeled on the provided wire leads. CAP unused wire! CAUTION! Failure to CAP unused wire may result in a shock hazard or unsafe condition as well as equipment failure. IMPORTANT: For the BS100 SA you must connect AC power before connecting the emergency ballast. SA option must specify 120V or 277V. 7. Snap reflector into place. 8. Insert the lamps into the lamp holders and twist to lock them into place. 9. Install closure clips. Reposition the lens and snap each of the four (4) or eight (8) clips into place (a clack sound is made). 10. Turn on AC. SAVE THESE INSTRUCTIONS!
4 TYPICAL INSTALLATION 1. REMOVE DIFFUSER / LENS 2a. REMOVE REFLECTOR FROM HOUSING 2b. EXTRACT MOUNTING HARDWARE-INCLUDED 3. INSTALL ELECTRICAL WIRING CONNECTOR BUSHING IS INCLUDED 4. HANG REFLECTOR FROM ENCLOSURE CLIPS
5 L i k MOUNTING 5. COMPLETE ELECTRICAL CONNECTIONS 6. INSTALL LAMPS L N L Line / Hot N Neutral / Common BALLAST Ground Labeled wire leads are provided for Line / Hot, Neutral / Common and Ground. Labels will indicate the rated input voltage: 120V or 277V 60Hz. Exact ballast and wiring configuration may differ from image above: FOLLOW ACTUAL WIRE LABELS. SA option must specify 120V or 277V 7. INSTALL LENS/DIFUSER/CLOSURE CLIPS SAVE THESE INSTRUCTIONS!
6 MOUNTING OPTIONS DIMENSIONS 4FT FT 1/2 IP CONDUIT KNOCKOUT 0.50 STAINLESS STEEL MOUNTING PLATE
7 MOUNTING OPTIONS INSTALL MOUNTING HARDWARE SURFACE MOUNT CHAIN HANG MOUNT (CH) SINGLE PENDANT MOUNT (SPK) WALL MOUNT FIXTURE REMOVAL (IF NECESARY) TRUNION MOUNT (TM) PIVOT MOUNT (PM)
8 AIRCRAFT CABLE MOUNTING MOUNTING OPTIONS DOUBLE PENDANT MOUNTING FEED SUSPENSION CANOPY KIT NON FEED SUSPENSION CANOPY KIT FEED SUSPENSION CANOPY KIT NON FEED SUSPENSION CANOPY KIT J-BOX J-BOX CROSS BAR CANOPY CROSS BAR (screws not included) LOCK NUT (for double lock on stem) (2) SCREWS IN J-BOX (screws not included) CANOPY WIRE TIES CABLE GRIPPER SLIP RING (TO POSITION CANOPY) SET SCREW FOR SLIP RING STEM (1/4 IPS) AIRCRAFT CABLE POWER CORD WIRE TIES POWER CORD STAINLESS STEEL MOUNTING PLATE STAINLESS STEEL MOUNTING PLATE LOCK NUT LOCK NUT
9 MOUNTING OPTIONS JUNCTION MOUNT (JM) from dimmer control from main line Purple (+) Gray (-) JM allows direct connection to j-box. JM configuration voids the IP66 wet location rating. 3/4 Thick Neoprene Gasket DIMMING WIRING DIAGRAM Purple(+) Gray(-) Main AC Main AC DIMMING 0-10V WALL DIMMER For dimmer switch wiring details, please refer to dimmer manufacturer s installation guide. (Dimmer not supplied by Beghelli) NOTE: WIRE LOCATIONS WILL VARY. REFERENCE WIRES BY COLOR NOT LOCATION Beghelli Canada th Avenue Markham, Ontario L3R 4R3 Canada P: (905) F: (905) Beghelli USA 3250 Corporate Way Miramar, Florida USA P: / P: F: Beghelli Mexico Av El Marques No. 70, Interior Mpio. El Marquez Queretano, QRO. Mexico P: / F:
When using electrical equipment, basic safety precautions should always be followed including the following:
INDUSTRIAL INSTALLATION INSTRUCTIONS Illumina BS100LED2FT-PLUS EACH MODEL NUMBER CONSISTS OF THE FOLLOWING: SERIES / LENGTH / OPERATION / LUMENS / COLOUR TEMP. / INPUT SERIES: LENGTH: OPERATION: BS100LED2PLUS
More informationMEDIA LED. Pendant Standard Mount Installation ou de montage WARNING:
MEDIA LED Pendant Standard Mount WARNING: Disconnect main power at the source prior to installation! Thread gripper base onto 1 /4 20 stud, or with #8 screw. Depress gripper nozzle to insert aircraft cable.
More informationHP-2 / HP-6 Direct Installation Instructions Overview
Overview Helpful Video 0-10V Dimming Step 1 Mounting & Suspension Page 2 Step 2 Identification & Preparation Page 3 Step 3 Mounting to Structure Page 4 NOTE Step 4 Page 5 This installation requires proper
More informationINSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR NEW YORK 18 WATT SERIES
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR NEW YORK 18 WATT SERIES IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following:
More informationInstall Guide PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE
PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE This product must be installed in accordance with the applicable code by a person familiar with the construction and operation of the product and the hazards
More informationInstallation Instruction
T F W 604.549.9379 604.549.9555 fluxwerx.com Installation Instruction DRIVER ENCLOSURE Ceiling Type Version Grid Battery Pack GRID MOUNT INSTALL OPTIONS OPTION 1: Standard Vertical Grid drivers can be
More informationSure-Lites. Installation Instructions for the Sure-Lites UX Self Powered Exit Sign with Self Diagnostics. IB505037EN Important Safeguards
049-289 Sure-Lites Installation Instructions for the Sure-Lites UX Self Powered Exit Sign with Self Diagnostics. WARNING Risk of Fire/Electric Shock If not qualified, consult an electrician. WARNING Risk
More informationULTRA PERFORMANCE LED TUBE INSTALLATION INSTRUCTIONS
Ultra Performance LED Tube Installation Instructions Page 1 of 7 ULTRA PERFORMANCE LED TUBE INSTALLATION INSTRUCTIONS These instructions do not purport to cover all details or variations in components
More informationHIGHBAY RAIL 400W INSTALLATION INSTRUCTIONS
TM INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with the National Electrical Code and
More informationInstallation and Operation Instructions 10/04/13
ELI-S-100 With DIMMING CAPABILITIES Installation and Operation Instructions eli series emergency lighting inverters NRTL/C! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS This document explains mounting for pendant, recessed, and wall PENDANT - STEP ONE INSTALL MOUNTING POINTS Non-power feed mounting points may be positioned 1 to 12 or 12 to 18
More informationAEROBAY INSTALLATION INSTRUCTIONS
AEROBAY INSTALLATION INSTRUCTIONS AEROBAY IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with the National Electrical
More information3. Please ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.
FLUORESCENT EMERGENCY BALLAST WARNING: When using this lighting device, safety precautions should be followed at all times. CAUTION: Verify that all replacement lamp types marked on the installed luminaire
More informationINSTALLATION AND OPERATING INSTRUCTIONS
THINLINE 2.0 - TL2 PENDANT MOUNTING DIE CAST ALUMINUM LED EXIT SIGNS INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS When using electrical equipment,
More informationEMERY SKY SUSPENDED LED LUMINAIRE
EMERY SKY SUSPENDED LED LUMINAIRE IP20 DRY LOCATION 120V- 277V AC SAFETY & WARNINGS 1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS 2. Install in accordance with national and local electrical code regulations.
More informationInstruction/Installation Manual
Instruction/Installation Manual Retrofit:LED Tube Lamp 4ft. Fluorescent T8/T10 Replacement 1 SECTION 1 - General Information Kit components:1-led Tube, 1-Label and 1-Set of Instructions Models were only
More informationOperating Instructions
DuroSite & SafeSite Area Light with Adapters Important Information: These instructions contain safety information, read and follow them carefully. Dialight will not accept any responsibility for injury,
More informationSAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be
More informationNT-300 Series Single Circuit Track System & Accessories
NT-300 Series Single Circuit Track System & Accessories Type Project Catalog No. Lamp/Wattage PRODUCT DESCRIPTION Low profile, extruded aluminum track with 20-Amp rated flat, solid integral copper conductors.
More informationAssembly instruction. Pendant Light Toccata GENERAL REMARKS ON SAFETY: Technical data: BOM
GENERAL REMARKS ON SAFETY: Read all of these instructions before installing fixtures. Keep all of the instructions for future reference. Turn off power before installing fixture. Installation is to be
More informationIMPORTANT SAFEGUARDS
INSTRUCTION MANUAL NON-INTERRUPTIBLE AC INVERTER SYSTEM MODEL EAC FTM 350 FOR EMERGENCY LIGHTING POWER IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed,
More informationInstallation Instructions: Eco SpunBay LED High Bays
Installation Instructions: Eco SpunBay LED High Bays Installation Notes & Precautions: Read all precautions, warnings, instructions contained in this document. These instructions can be used to install
More informationMaxLite LED UTILITY WRAP FIXTURES
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More informationElle Surface Mounting Instructions
Step 1: Preparation, page 2 Warnings CAUTION risk of fire and this product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation
More informationLED IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationFINA SUSPENDED INSTALLATION INSTRUCTIONS
FINA SUSPENDED INSTALLATION INSTRUCTIONS 3 AC Cable Mounting (AC3) Installation... 2-4 AC Cable to Hub Mounting (AH4) Installation... 5-7 Pendant Pipe Mounting Installation... 8-9 Canopy Detail... 10-11
More informationSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Champ Fluorescent Luminaires DMVFB Auxiliary Series - 52, 64, & 84 Watt Installation & Maintenance Information SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE IF 1713 IMPORTANT SAFEGUARDS READ AND FOLLOW
More informationAlbeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series)
GE Lighting Installation Guide Albeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series) Features UL 1598 Suitable for Wet Locations IP66 Rated Ingress Protection BEFORE YOU BEGIN Read these
More informationPrestige Series Edge-Lit LED Sign IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
Prestige Series Edge-Lit LED Sign AC, AC/DC and Self-Powered models Prestige Series Edge-Lit LED Sign WARNING: Risk of Shock. Disconnect Power before Installation. IMPORTANT SAFEGUARDS When using electrical
More informationTECTONIC LED CORP. ISO
TECTONIC TECTONIC LED CORP. ISO 9001:2000 Products RoHs Compliance Instruction Menu Retrofit:LED Tube Lamps SECTION 1 - General Information Kit components: 1-LED Tube, 1-Label and 1-Set of Instructions
More informationCustomer service: or Upper mounting ring. Canopy
Components included: Upper mounting ring Canopy Fixture base Fluorescent - 2 x 42 W 4-pin compact fluorescent lamps required (not included). Lutron recommends GE, Sylvania, or Philips lamps that are certified
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationALL700/ALL700-CM INSTALLATION INSTRUCTIONS
ALL700/ALL700-CM INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power
More informationBALT5-800 LOW-PROFILE FLUORESCENT EMERGENCY BALLAST
BALT5-800 LOW-PROFILE FLUORESCENT EMERGENCY BALLAST APPLICATION The BALT5-800 low-profile fluorescent emergency ballast works in conjunction with the AC ballast to convert new or existing fluorescent fixtures
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationInstallation Instructions: Memory-Dimmable SEP T8 Tube Lamps
Installation Instructions: Memory-Dimmable SEP T8 Tube Lamps Installation Notes & Precautions: Memory-Dimmable SEP T8 LED Tube Lamp Read all precautions, warnings, instructions contained in this document.
More informationInstallation Instructions Central Battery Units
Phone: 605.542.4444 concealite.com! Installation Instructions s Please Save These Instructions Important Safeguards Read and Follow All Safety Instructions When using electrical equipment, basic safety
More informationCiros P-ID-5200 Pendant-Mounted Indirect/Direct
Type: Project: Ciros P-ID-5200 Pendant-Mounted Indirect/Direct 2 5/8" (67) 2 5/8" (67) Specifications 10 1/2" (267) 10 1/2" (267) U.S. Patent No. D431,086 HOUSING. Two-sided housing, 6063 T6 extruded aluminum.
More informationLightWave Lighting Technology
LightWave Lighting Technology About the company Since the inception of the company in 1998, LightWave has utilizes its expertize in lighting technology to make products that are energy efficient, cleaner
More informationINSTRUCTION MANUAL. IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following:
IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. CAUTION To prevent electrical
More informationHPNLS-HO. Installation Manual
Installation Manual WARNING: Do not lift fixture by cables. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/or putting undue pressure
More informationINSTRUCTION MANUAL IMPORTANT SAFEGUARDS. When using electrical equipment, basic safety precautions should always be followed, including the following:
INSTRUCTION MANUAL IMPORTANT SAFEGUARDS SERIES D LIGHTING EQUIPMENT When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY
More informationSAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS EMERGENCY FLUORESCENT BATTERY PACK MODEL PS300, PSQ500, PS600, PS1400 CAUTION: For safety and proper operation, read and follow instructions carefully before installation. FIELD
More informationUniversal Retrofit System Installation Instructions Revised:
Universal Retrofit System Installation Instructions Revised: 20150624 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency to
More informationInstallation Instructions: External-Driver SEP T8 LED Tube Lamp
Installation Instructions: External-Driver SEP T8 LED Tube Lamp Installation Notes & Precautions: External-Driver SEP T8 LED Tube Lamp Read all precautions, warnings, instructions contained in this document.
More informationINSTALLATION INSTRUCTIONS LIGHTPLANE 3.5. LP3.5 Suspended LED. A nd Avenue, Unit 1. CA P E W alwusa.
Oakland, INSTALLATION INSTRUCTIONS LIGHTPLANE 3.5 LP3.5 Suspended LED A 1035 22nd Avenue, Unit 1 n CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings! 1. Read all instructions.
More informationADVANTAGE SERIES Vaportight Fixtures
Short Specification: The Advantage Vaportight fixtures are approved for use in vandalresistant, dust, wet and spray-down locations. This series was designed with electrical distributors for the demands
More informationKT-EMRG-1400-SL /B. 3. Please ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.
FLUORESCENT EMERGENCY BALLAST WARNING: When using this lighting device, safety precautions should be followed at all times. CAUTION: Verify that all repalcment lamp types marked on the installed luminaire
More informationWHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING THE FOLLOWING:
SURE-LITES Installation Instructions For FBP-1-40X IMPTANT SAFEGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING THE FOLLOWING: 1. READ AND FOLLOW ALL
More informationHAZARDOUS LOCATION STREET LIGHT SLA SERIES INSTALLATION INSTRUCTIONS
Single Module Series Double Module Series Triple Module Series IMPORTANT: Please read carefully before installation and retain for future reference To prevent possible shock hazard, the fixture should
More informationINSTRUCTION MANUAL IMPORTANT SAFEGUARDS. When using electrical equipment, basic safety precautions should always be followed, including the following:
INSTRUCTION MANUAL IMPORTANT SAFEGUARDS SERIES D LIGHTING EQUIPMENT When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY
More informationSAVE THESE INSTRUCTIONS!!
IMPORTANT: Please read carefully before installation and retain for future reference To prevent possible shock hazard, the fixture should be installed by a qualified licensed electrician All electrical
More informationInstallation Instructions & Users Manual IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Crystal Recessed Edge- lit LED Exit Signs Series CRRBB & CRRAC Battery Backup & AC Models 01.18.06 Installation Instructions & Users Manual IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
More informationALL W INSTALLATION INSTRUCTIONS
ALL1000-3300W INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power source
More informationElle Surface Mounting Instructions
Step 1: Preparation, page 2 Warnings CAUTION risk of fire and this product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation
More informationMONORAIL KITS INSTALLATION INSTRUCTIONS PENDANTS
MONORAIL KITS PENDANTS JESCO Lighting Group is a UL and ETL listed company Copyright 2011 JESCO Lighting Group. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS Be sure to read and unsderstand the following
More informationNMF 2 SERIES Non-Metallic Enclosed and Gasketed Fluorescent Lighting for Wet and Damp Locations
NMF 2 SERIES Non-Metallic Enclosed and Gasketed Fluorescent Lighting for Wet and s NEMA 4X UL 1598 Wet & s CUL IP65 NSF Enclosure N M F 2 339 NMF2 SERIES Non-Metallic Enclosed and Gasketed Fluorescent
More informationLinear Fluorescent Highbays. A comprehensive selection of high output commercial/industrial fluorescent lighting
Linear Fluorescent Highbays A comprehensive selection of high output commercial/industrial fluorescent lighting Linear Fluorescent Highbay Lighting T-Series Full Body, Specification Grade Fluorescent Highbay
More information1Unpack fixture. Suspensions/canopies are ordered and
DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at 1-800-448-4131 questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions 2Determine
More informationHxO Profile System - Suspension
INDIRECT 1 14/16 47mm DIRECT L3HX-SUS-SYS DI OP X / / Article # Installation Distribution Diffuser Length Angle Couplers Voltage Linear Spot x Qty Electrical Power Feed Suspension Cable Finishes Lighting
More informationLED W IMPORTANT: not provide. contact the. fire. LED only. entrap heat. applications. carry high GENERAL: Compare. material.
2016 Philips Lighting Holding B.V. All rights reserved. AEROSCAPE LED W WALL SCONCE IMPORTANT: Read carefully before installing. All work should be performed by a qualified Electrician. These instructions
More informationINSTRUCTION MANUAL. IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following:
SERIES E Emergency Lighting Equipment IMPTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
More informationBAL3000 BAL3000. Fluorescent Emergency Ballast Lumens. Specification Sheet. Emergency Ballast 1/19/2012. Project: Catalog#: Approved by:
1/19/2012 Fluorescent 1450-3000 Lumens Works in conjunction with an AC ballast to convert new or existing fluorescent fixtures into unobtrusive emergency lighting Maintains illumination of one or two lamps
More informationApplications. Illustrated Features
Applications For use in locations where a high degree of corrosion resistance is required. FR Series: For use in areas where high humidity or water vapor are present Typical uses include meat- or food-processing
More informationInstallation Documentation ID-2663
Installation Documentation ID-2663 FLEXXA LP INDIRECT, SEMI-INDIRECT SYSTEMS Ergoline Modular Instructions included with this package: Document 266-pend 266-end 266-joint General Description Flexxa LP
More informationCirca Ambient Interior Luminaire
IMPORTANT SAFETY INSTRUCTIONS 1. Read carefully before installing fixture. Retain for future reference. To prevent electrical shock, turn off electricity at fuse box before proceeding. 2. Failure to follow
More informationFluorescent Lamp Wattages. Fluorescent Optics T5 = F14 (2') F21 (3',6') F28 (4',8') NB Narrow Beam (60 ) WB Wide Beam (100 )
INDOOR R FLUORESCENT INDOOR R FLUORESCENT SMS/SMM MOUNT Prefix Mounting Optics Light Source & Wattage LIN = Linea SMS-U Surface, Uplight, SMM-U Surface, Uplight, Multiple Fixture Run SMS-D Surface, Downlight,
More informationwww.greenelectricalsupply.com 1x4 2x2 & 2x4 Read all instructions and warnings before attempting installation. RISK OF FIRE OR ELECTRIC SHOCK. LED RETROFIT INSTALLATION REQUIRES KNOWLEDGE OF LUMINAIRES
More informationLED Utility Wrap Fixture
Operating Instruction Please read and save these instructions. Read through this owner s manual carefully before using product. Protect yourself and others by observing all safety information, warnings,
More informationwww.greenelectricalsupply.com Dimensions not to scale 4.4 Width 6.75 ; with latches 7.33 2 ; 27.68 4 ; 51.65 8 ; 100 Lengths, nominal; actual AVAILABLE Simkar is proud to offer fixtures that comply to
More informationStrip Fixture URS Light Bar Retrofit Installation Instructions Revised:
Strip Fixture URS Light Bar Retrofit Installation Instructions Revised: 20180126 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency
More informationLED IMPORTANT SAFETY INSTRUCTIONS
U02301 Rev. B Page 1 of 8 U02301 Rev. B Page 2 of 8 IBG LED HIGHBAY INSTALLATION INSTRUCTIONS WARNING: Please read all important safety instructions prior to installation of this product. A) Identification
More informationECO-T LED RECESSED TROFFER USER MANUAL
ECO-T LED RECESSED TROFFER USER MANUAL INSTALLATION GUIDE FOR: 2X2: MLRT22D4535 MLRT22D4541 MLRT22D4550 2X4: MLRT24D5535 MLRT24D5541 MLRT24D5550 Thank you for purchasing this MaxLite product. For additional
More informationLumeLEX 2084 SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2084 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationMaxline Profile System - Suspension
DIRECT 5 7/8 150mm 6 1/4 158mm L3ML-SUS-SYS DR Article # Distribution Diffuser Length Angle Voltage Linear Spot Electrical Power Suspension Finishes Couplers Feed Cable x / / Accessories Product Distribution
More informationINSTALLATION INSTRUCTIONS SUPERPLANE 2.5. Suspended. A nd Avenue, Unit 1 Oakland, CA P E W alwusa.
INSTALLATION INSTRUCTIONS SUPERPLANE 2.5 Suspended A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP2.5S - Safety & Warnings! 1. Read all instructions. 2.
More informationES44-LED SERIES DIRECT OR INDIRECT HIGH EFFICIENCY LED - RECESSED, SURFACE, WALL OR SUSPENDED
ES44-LED SERIES DIRECT OR INDIRECT HIGH EFFICIENCY LED - RECESSED, SURFACE, WALL OR SUSPENDED PERFORMANCE CHARACTERISTICS Optical Efficiency: 90.5% max Lumens per watt: 180 max Lumen output: 2200Lm/ft
More informationIdaho Profile System - Trimless
3 4/16 82mm DIRECT 3 9/16 90mm 3 6/16 85mm L3ID-TRI-SYS DR OP Article # Distribution Diffuser Length Voltage Linear Electrical Mounting Brackets Lighting Control Product Distribution Diffuser Length Voltage
More informationALL200RM/ALL200RM-CM
ALL200RM/ALL200RM-CM INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationEEQ SERIES COMPACT FLUORESCENT EMERGENCY FACTORY SEALED LIGHTING FIXTURES
INSTALLATION, OPERATION & MAINTENANCE DATA SHEET (EEQ SERIES COMPACT FLUORESCENT EMERGENCY FACTORY SEALED LIGHTING FIXTURES) EEQ SERIES COMPACT FLUORESCENT EMERGENCY FACTORY SEALED LIGHTING FIXTURES CAUTION:
More information003 3 foot foot RUN Nominal Length* * For actual lengths see
M125 Project: Type: Qty: Series Lamping Shielding Mounting Nominal Length Finish Voltage Options Series Lamping Shielding Mounting Nominal Length Finish Voltage Options M125 (M125/9 Direct) Multi-Mount
More informationTrack Accessories. Single Circuit Track. L Connector T Connector X Connector. Mini Connector Floating Canopy End Feed Kit.
Single Circuit Single Circuit Track Live End Connector Flexible Connector Straight Connector Track supplied with dead end and mounting hardware Live end connector used for direct wiring Flexible connector
More informationNOVO LIGHTED MIRROR. Installation Instructions
NOVO LIGHTED MIRROR Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Must be installed by a qualified technician. Read these installation instructions. Keep these instructions for future use. Follow
More informationLED IMPORTANT SAFETY INSTRUCTIONS
LED IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage
More informationSAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFEGUARDS! When using electrical equipment, basic safety precautions should always be
More informationInstallation And Operation Instructions For FHSCP-UNV Series Emergency LED Drivers Models: FHSCP-UNV-5WL, 7.8WL, 10.7WL, 13.
Installation And Operation Instructions For FHSCP-UNV Series Emergency LED Drivers Models: FHSCP-UNV-5WL, 7.8WL, 10.7WL, 13.7WL, 17WL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety
More informationSURE-LITES FBP140XLP Instruction Manual
SURELITES Instruction Manual IMPORTANT SAFEGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING THE FOLLOWING: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. CAUTION:
More informationTORi INSTRUCTION SHEET. Minimalist Linear Fixture T5/T5HO. CSS - Cable Suspended. 1. Cut cables to desired length - take care not to fray cable ends.
TORi Minimalist Linear CSS - Cable Suspended J-BOX (BY OTHERS) 3-O or 4-0 MUD RING (BY OTHERS) J-BOX BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS (BY OTHERS) CANOPY STND - 5 CANOPY 1. Cut cables to
More informationUFO-RP2 FLUORESCENT BATTERY PACK IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
FLUORESCENT BATTERY PACK IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. - To
More informationMaxLite LED Linear HighBay Fixtures
Operating Instructions MaxLite LED Linear HighBay Fixtures General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions,
More informationUFO-RP3 FLUORESCENT BATTERY PACK IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
FLUORESCENT BATTERY PACK IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. - To
More informationVision Profile System - Surface
4 1/8 105mm DIRECT 1 15/16 49mm L3VI-SUR-SYS DR OP X Article # Mounting Distribution Diffuser Length Angle Voltage Linear Spot x Qty Electrical Finishes Accessories Type Couplers / Lighting Control Product
More informationIdaho Profile System - Suspension
INDIRECT DIRECT ASY 3 1/8 80mm 2 15/16 75mm L3ID-SUS-SYS Article # Distribution Diffuser Length Angle Voltage Linear Spot x Qty Electrical Power Suspension Finishes Lighting Couplers Feed Cable Controls
More informationSURFACE/CEILING & SUSPENDED MOUNT INSTALLATION
SURFE/CEILING & SUSPENDED MOUNT INSTALLATION E477827 E477827 APPLICATION NL luminaires are designed for use indoors, outdoors, wet locations, areas containing moisture, dirt, corrosion, vibration and rough
More informationTRAC-LITES One Circuit Trac System TRAC SECTIONS & SYSTEM COMPONENTS R Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Reduced-profile, single-circuit trac sections for surface or pendant mounting. Compatible with a full range of feed, connector
More informationLighting Systems Argus-7
Page 1 of 5 1 1. (3.5cm) 1.7 (4.3cm) 4 5 Rectilinear 3 1.81 (4.6cm) Extruded Linear Louver.5 (.64cm) 5. (1.7cm) 9. (.86cm) 1 1. (3.5cm) 1.7 (4.3cm) 4 5 Tapered 3 1.81 (4.6cm).75 (.7cm) Feature Specifications
More informationProduct Overview. High Power 7W/ft. Fixture Summary (see following pages for more information) Power Level Watts Per Foot
Linea 1.5" Pendant Direct Features Quick-Line Linea 1.5" delivers your design scenario seamlessly and on time, everytime. Streamlined and flexible, these architectural LED pendants provide the freedom
More information