6 8 Deringer 20/30 Maintenance Instructions READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL M-F 8:00 AM 4:30 PM PST

Transcription

1 6 8 eringer 20/30 Maintenance Instructions RE INSTRUTIONS IN FULL EFORE INSTLLTION. QUESTIONS? LL M-F 8:00 M 4:30 PM PST t ackflow irect we are committed to making our products as easy to install as possible. We design for most contingencies, but installation may be different based on your regional regulations or system design. We are continually improving our products and instructions please help us by providing recommendations as to how we can improve or products or instructions. If you have any difficulties at all, please give us a call. Thank you for purchasing our product! IMPORTNT NOTE: We use Stainless Steel Hardware where possible. Therefore, it is best to have Silver ntiseize available to use on all non-wetted bolts only a small amount is needed. WRRNTY INFORMTION: Please visit our website for our official warranty REV: 12/22/2015 -INST-02030

2 Tools Required: This list is the recommended tools for ease of installation. Other versions of the same tool can be used. For example, llen Wrenches instead of llen rive Sockets. #2 Philips Head Screwdriver djustable Wrench #2 Flathead Screwdriver ackflow irect Test ock Wrench Ratchet Expanding Pipe Pliers 15/16 Socket 1 1/8 Socket Wood lock - 2 x 4 x 5 Wood lock 1 x 2 x 16 QUESTIONS: Please call us at M-F 8:00 M 4:30 PM PST or us at techhelp@backflowdirect.com -INST Rev 12/22/2015 opyright 2011 ackflow irect, LL Page 2 of 20

3 losing Shut-Off Valves Prior to Maintenance Note: When yellow/orange position indicator flags are parallel with the flow of water the shut-off valves are in the open position. efore doing any maintenance be sure the yellow or orange flow indicators (flags) are perpendicular to the flow of water valve body indicating shut-off valves are in the closed position (). Note FLOW FLOW 1. Slowly rotate Shut-Off Valve #2 Handle () clockwise to the closed position. Flag perpendicular to flow (). 2. Slowly rotate Shut-Off Valve #1 Handle () clockwise to the closed position. Flag perpendicular to flow (). -INST Rev 12/22/2015 opyright 2011 ackflow irect, LL Page 3 of 20

4 Opening Test ocks and leeding ll Pressure from the Line efore Maintenance 1. O NOT OPEN Main Test ock Number 1, as it is still subject to line pressure. 2. Using the ackflow irect test cock wrench or a small adjustable wrench open () Main Test ock Number 4. (Test ock is open when wrench flats are parallel to water flow through test cock) FLOW 3. Using a #2 Flathead Screwdriver open ypass Test ock Number 2. (Test ock is open when screwdriver slot is parallel to water flow through test cock () ) 4. Using the ackflow irect test cock wrench or a small adjustable wrench open Main Test ock Number Using a #2 Flathead Screwdriver open ypass Test ock Number Using the ackflow irect test cock wrench or a small adjustable wrench open Main Test ock Number 2. -INST Rev Rev 12/22/ /23/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 4 of 20

5 Removing ccess Port over Plate 1. Using a 15/16 socket wrench loosen all eight bolts on the access port cover plate (). 2. Remove bolts and tapered washers () and store in a safe place. e careful not to lose tapered washers as the access cover will not seal properly without the tapered washers. 3. Remove access port cover plate (). o not remove ccess Port O-ring (). -INST Rev Rev 12/22/ /23/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 5 of 20

6 Removing the First ual-ction heck Module 1. Use a 15/16 Socket Wrench to loosen the check retainer bolts on both sides of the valve body (). o not completely remove check retainer bolts from valve body. Merely loosen the bolts until the ends of the bolts are flush with the inner wall of the valve body(). llow easy removal of heck Modules 2. Insert a flathead screwdriver between the inner valve body and the First heck Module Flange (), gently coax the First heck Module in the downstream direction until the First heck Module can easily be removed from the access port by hand. FLOW -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 6 of 20

7 Removing the Second ual-ction heck Module 1. Use a 1 1/8 Socket Wrench to loosen the heck Retainer olts on each side of the valve body (). o not completely remove check retainer bolts from valve body. Merely loosen the bolts until the ends of the bolts are flush with the inner wall of the valve body(). 2. Insert a flathead screwdriver between the inner valve body and the Second heck Module Flange (), gently coax the Second heck Module in the upstream direction until the Second heck Module can easily be removed from the access port by hand. FLOW -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 7 of 20

8 isassembly and Maintenance of y-pass heck Valve 1. Use an adjustable wrench to rotate heck over () counterclockwise to remove. 2. Examine over Plate O-ring () for damage or fouling. 3. Remove Spring (). 4. Remove heck Poppet ssembly () and examine for damage or fouling. 5. Examine seat cage for Seat age and examine for damage or fouling to the Sealing Seat. o not remove unless the seat cage is being replaced. 6. Reverse the order of above instructions to reassemble y-pass heck Valve. -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 8 of 20

9 isassembly and Maintenance of y-pass heck Valve (continued) 1. To replace a damaged Red Silicone Poppet isk, use a #2 Philips Head Screwdriver to remove the isk Retaining Screw (). 2. Remove isk Retaining Washer (). 3. Use a Flathead Screwdriver to remove the gasket from Poppet avity (). 4. Install new Red Silicone Poppet isk (). 5. Reverse the order of the above instructions to reassemble heck Poppet ssembly. 6. Reverse the order of the instructions on the previous page to reassemble ypass heck ssembly. -INST Rev 12/22/2015 opyright 2011 ackflow irect, LL -INST Rev 12/22/2015 opyright 2011 ackflow irect, LL Page 9 of 20

10 Removing ypass Meter 1. Using the all Valve Handles close the #2 ypass all Valve () and then #1 ypass all Valve (). (all Valve is closed when T handle is perpendicular to water flow through all Valve). FLOW 2. Using a #2 Flat Head Screw river open ypass Test ock #2 () and then open ypass Test ock #1 (). (Test ock is open when screw driver slot is parallel to water flow through Test ock). 3. Using a large adjustable pliers or wrench unscrew and retract ypass Meter oupling Nuts (E). Remove the Gaskets (F) on both sides of ypass Meter. 4. Gently remove ypass Meter (G) from line. It is OK if the bypass fittings move slightly during the removal process. 5. Reverse order of above instructions to reinstall ypass Meter. Remember install Gaskets (F) before threading Meter oupling Nuts into place. E E G F E -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 10 of 20

11 Maintenance of First ual-ction heck Module 1. Use a #2 Philips Head Screwdriver to remove Tower Screws () from the First heck Seat () The ouble Torsion Spring is captured () and does not to be retained during maintenance. 2. fter removing the Tower Screws () Examine the Elastomer isk () and heck Seat (E) for fouling or damage. 3. Should Elastomer isk () need replacement unscrew isk Retainer Screws (F) and remove isk Retainer (G). arefully remove and replace Elastomer isk (). When replacing Elastomer isk () be certain that no air, water or debris is trapped in the lapper (H) cavity behind the Elastomer isk (). H F E G 4. Reverse the order of the above instructions to reassemble check. Elastomer isk must be flat in lapper (H) cavity before tightening isk Retainer Screws (F). o not cross thread isk Retaining Screws (F). -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 11 of 20

12 Maintenance of First ual-ction heck Module Note: The diagram below shows the correct orientation of the First ual-ction heck Module when being re-attached to the seat. In order to maintain the performance of the valve pay attention to the proper orientation of the check module. -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 12 of 20

13 Maintenance of Second ual-ction heck Module 1. Use a #2 Philips Head Screwdriver to remove Tower Screws () from the Second heck Seat () The ouble Torsion Spring is captured () and does not to be retained during maintenance. 2. fter removing the Tower Screws () Examine the Elastomer isk () and heck Seat (E) for fouling or damage. 3. Should Elastomer isk () need replacement unscrew isk Retainer Screws (F) and remove isk Retainer (G). arefully remove and replace Elastomer isk (). When replacing Elastomer isk () be certain that no air, water or debris is trapped in the lapper (H) cavity behind the Elastomer isk (). H F E G 4. Reverse the order of the above instructions to reassemble check. Elastomer isk must be flat in lapper (H) cavity before tightening isk Retainer Screws (F). o not cross thread isk Retaining Screws (F). -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 13 of 20

14 Maintenance of Second ual-ction heck Module Note: The diagram below shows the correct orientation of the Second ual-ction heck Module when being re-attached to the seat. In order to maintain the performance of the valve pay attention to the proper orientation of the check module. -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 14 of 20

15 Installing Second ual ction heck Module 1. Insert Second heck Module () into ccess Port () with Second heck Towers () pointing downstream. Push Second heck Module () downstream into Valve Sealing Ring () until heck O-ring (E) rests against Valve Sealing Ring (). oax Second heck Module () into its fully seated position by hand. 2. lternatively place 2 x4 piece of wood cut to 5 length (F) against the backside of the Second heck Seat Ring (G). Using a 1 x4 piece of wood cut to 16 length (H) as a lever between ccess Port Wall the 2 x4 (F) gently coax the Second heck Module () into its fully seated position. 3. e certain Second heck Module () is fully seated and heck O-ring (E) is NOT fish mouthed or damaged. 4. Tighten the Second heck Retaining Screws (I) ONLY FTER the First heck Module () as been installed. FLOW H G WRNING: The Second heck Module must be fully seated to insure Retainer Screws do not bind against heck Seat. inding Retainer Screws against heck Seat will result in permanent damage to Second heck Modules. inding E Not inding F I -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 15 of 20

16 Installing First ual-ction heck Module 1. Insert First heck Module () into ccess Port () with First heck Towers () pointing downstream. Push First heck Module () upstream into Valve Sealing Ring () until heck O-ring (E) is resting against Valve Sealing Ring (). oax First heck Module () into its fully seated position by hand. F 2. lternatively, using a piece of 1 x4 wood cut to 16 length (F) as a lever between the Second heck Seat (G) and the First heck Towers (), coax the First heck Module () into its fully seated position. E G 3. e certain First heck Module () is fully seated and heck O-ring (E) is NOT fish mouthed or damaged. 4. Now fully tighten the First and Second heck Retaining Screws (I). FLOW inding Not inding WRNING: The First heck Module must be fully seated to insure Retainer Screws do not bind against heck Towers. inding Retainer Screws against heck Towers will result in permanent damage to First heck Modules. I -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 16 of 20

17 Installing ccess Port over 1. It is best to never remove the ccess Port O-ring (). Should the ccess Port O-ring () become dislodged, simply insert it back into ccess Port Groove (). 2. Slide the ccess Port over () into place being certain that ccess Port O-ring () does not become dislodged during the process. 3. Insert over olts () and Tapered Washers (E) into Tapered over Holes (F). Tapered Washers (E) must be properly installed or the ccess Port over () will not seal under pressure. 4. Use 15/16 Socket Wrench (G) to tighten the 4 center over olts () alternating from one side of the valve to the other. Then Tighten the four corner bolts alternating from one side of the valve to the other. F G E -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 17 of 20

18 lose Test ocks and ouble heck all losing/sealing Mechanisms 1. Using the ackflow irect Test ock Wrench or a small adjustable wrench close Main Test ocks Number 1, 2 and 3 (). (Test ock is closed when wrench flats on stem are perpendicular to water flow through Test ock) 2. Using a #2 Flathead Screwdriver lose ypass Test ock Number 1 and 2 (). (Test ock is closed when screwdriver slot on stem is perpendicular to water flow through Test ock) FLOW 3. Use the T handles to open bypass all Valve Number 1 () and then open bypass all Valve Number 2 (). (all Valve is open when T handle is parallel to water flow through all Valve) 4. ouble check to be certain of the following: ll over olts are Tightened (E) ypass heck Valve over is Tightened (F) ypass Meter oupling Nuts are Tightened (G) G F E -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 18 of 20

19 Open Shut-Off Valves to make ackflow Preventer Functional 1. Slowly rotate the Number 1 Shut-Off Valve Operation Handle () counter clockwise to the open position. (Shut-Off Valve is open when yellow/orange position indicator flags are parallel to the mainline water flow) 2. Slowly rotate the Number 2 Shut-Off Valve Operation Handle () counter clockwise to the open position. Note: Yellow/Orange Position Indicator Flags must be parallel to mainline water flow for ackflow Valve to be functional (). FLOW -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 19 of 20

20 6 - IMPORTNT 8 eringer NOTE 20/30 Maintenance Instructions Important Note: If a eringer is going to be installed outdoors and the tamper switches will not be wired into the fire alarm system, the wires will need to be cut and a plug will need to be installed to protect the internal components of the gear box. Step 1: Using wire cutters, cut the wires coming out of the gearbox as close to the gearbox as possible. Step 2: Use a piece of thread seal tape to seal the threads on the ½ NPT plug Step 3: Using an llen wrench, install and tighten the ½ NPT plug into the same threaded hole where the wires were previously cut. -INST Rev Rev 12/22/ /22/2015 opyright opyright 2011 ackflow 2011 ackflow irect, LL irect, LL Page 20 of 20