SPORTSTER SADDLEBAG KIT. i i02212
|
|
- Barbara Sims
- 5 years ago
- Views:
Transcription
1 General These saddlebags are designed to fit 99 and later Sportster Model Motorcycles, except XL00 Sport models with gas reservoir shock absorbers and 88R models. See the Service Parts pages for a list of the kit contents. Installation of this Saddlebag Kit on Sportster Models equipped with Detachable Docking Hardware requires the separate purchase of a Hardware Kit models must purchase hardware kit and 00 and later models must purchase hardware kit These kits are available for purchase at your Harley-Davidson Dealer. INSTRUCTIONS -J0890 REV Kit Number , 9-0 SPORTSTER SADDLEBAG KIT i0 WARNING Additional weight can affect motorcycle stability, handling characteristics, and safe operating speed. Do not exceed 7 lbs. (.8Kg) maximum load in each saddlebag. Evenly distribute weight between each saddlebag. Improper loading can cause vehicle handling problems leading to death or serious injury. Initial Installation Steps. Turn signal connectors Figure. -Place Deutsche Connectors ( Models) A Service Manual for your vehicle is available at your Harley- Davidson Dealer.. Remove the seat following Service Manual procedure. i0 WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (0008a) WARNING Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (0009a). Disconnect battery cables, negative cable first. i0. Turn signal connectors Figure. -Place AMP Connectors (997 and 998 Models) Remove Turn Signal. See Figures, and. Refer to the Appendix covering Amp and Deutsche Electrical Connectors in the applicable Service Manual and locate left and right signal wiring at turn signal connector () under seat.. Turn signal connector Figure. 8-Place AMP Connector (999 and Later Models) Unplug the connector and, following instructions in Service Manual, remove terminals from connector. of 9
2 i0 i05. Left turn signal connector. Right turn signal connector Figure. Disconnect Turn Signals at Tail/Stop Lamp (000 Shown) models: Pull turn signal wires through clips (if present) under fender. 999 and later models: Perform the following: a. Remove two screws securing tail/stop lamp lens assembly and remove lens assembly. b. See Figure. Disconnect left () and right () turn signal (two places) connectors from sockets. Cut wires at connector as close to terminal end as possible. Discard connectors and terminals. c. Gently pull wiring for both turn signals out (from tail/stop lamp assembly and from clip under rear of fender). d. Reattach tail/stop lamp lens using two screws removed in Step a. 5. See Figure 5. Remove the rear turn signals as follows: Remove the signal lamp assembly by removing the bolt () inside of the rear fender. Remove the lamp housing () from the bracket and pull the wiring through the bracket. Repeat for the opposite side. Discard the lamp brackets (). i008. Bolt. Lamp housing. Lamp bracket Figure 5. Rear Turn Signal Mounting Hardware. Signal relocation bracket. Conduit. Wires entering tube. Wires exiting tube i06 Figure 6. Install Wiring and Conduit into Bracket. Screw. Rubber plug Figure 7. Installing inch Signal Lamps (Standard Style) Attach Turn Signal to Bracket 6. If installing inch (Standard Style) Signal Lamps, proceed to step 7. If installing -/8 inch (Deuce Style) Signal Lamps, proceed to step Standard Style Signal Lamps See Figure 6. Obtain left signal lamp housing removed in previous step and left turn signal relocation bracket ()(Part Number ). Remove conduit () and cut wiring inches from entrance to lamp housing. Moisten wires with wet paper towel or rag and insert wires through relocation bracket () as shown until wires exit from opposite end of tube (). Slide conduit down to protect wiring at wire entrance of relocation bracket. See Figure 7. Apply LOCTITE (Blue) to screw () (Part Number 58). Using screw and lock washer (Part Number 70), attach lamp to signal relocation bracket as shown. Tighten securely. Repeat step 7 for the opposite signal. 8. Deuce Style Signal Lamps: See Figure 6. Obtain left signal lamp housing and left turn signal relocation bracket (Part Number ). Cut wiring inches from entrance to lamp housing. Moisten wires with wet paper towels or rag and insert wires through relocation bracket as shown until wires exit from opposite end of tube. -J0890 of 9
3 i05 i07. Screw. Washer. Spacer. Rubber plug Figure 8. Installing -/8 inch Signal Lamps (Deuce Style) See Figure 8. Apply LOCTITE (Blue) to screw (Part Number 09). Using screw (), lock washer () (Part Number 70) and spacer () (Part Number ), attach lamp to signal relocation bar as shown. Spacer should be installed between signal and signal relocation bracket Tighten securely. Repeat step 8 for the opposite side. Install rubber plug () over opening.. Butt connectors (staggered on wires). Conduit i0 Figure 9. Install Wiring Harness 9. See Figure 6. Install small black rubber plug () (Part Number 56-00) to cover opening of tube on bracket. Repeat for other side. 0. Obtain Wiring Harness (Part Number ) from kit. Pull the two wires out of the conduit. Terminals are attached to both ends of the wires to support all models. Before removing terminals you do not need, temporarily attach the correct terminals to the turn signal connector under the seat. Note the yellow tape on the wires models: Remove the terminals farthest away from the yellow tape. 997 and later models: Remove the terminals closest to the yellow tape. Cutting one of the wires slightly shorter before installing connectors will stagger the location of the butt splices and make sliding conduit over wiring much easier.. See Figure 9. Obtain two sealed butt connectors () (Part Number ) from kit. Following instructions in Service Manual under Installing Sealed Butt Connectors, match wire colors and splice wiring from turn signal to harness. Install butt connectors in a staggered pattern so conduit will tightly fit over wires. Slide conduit () from harness over butt splices and approximately " into bracket tube.. See Figure 0. Obtain three adhesive backed wire harness retaining clips ()(Part Number 00). Remove adhesive and install clips under fender strut () at locations as shown. -J0890. Retaining clips. Strut Figure 0. Install Wire Harness Retaining Clips Repeat Steps 6 through for the right turn signal. Set both turn signals aside. Install Support on Saddlebag To protect the finish on the saddlebag, lay it on a towel or other soft covering on your workbench.. See Figure. Obtain left saddlebag, four small grommets () (Part Number ) and one large grommet () (Part Number 7). Install the large grommet in the upper hole and four small grommets in the four remaining holes in the saddlebag assembly as shown.. Install one large spacer () (Part Number A) into the upper grommet and four small spacers () (Part Number A) into the small grommets as shown. On model motorcycles equipped with detachable docking points, you will need an additional hardware kit (part number ). This kit includes.5 inch screws (replacing.0 inch screws),.6 inch long hex spacers (replacing. inch of 9
4 i00 i000. Small grommet () and spacer (). Large grommet and spacer Figure. Install Grommets and Spacers long hex spacers), and 0.5 inch long spacers to be installed between the saddlebag support and strut cover. On 00 and later model motorcycles equipped with detachable docking points, you will need an additional hardware kit (part number 905-0). This kit includes.75 inch screws (replaces.0 inch screws),.85 inch long hex spacer (replaces. inch long hex spacer) and 0.75 inch long spacer to be installed between the saddlebag support and strut cover. 5. Starting at () in Figure, place a washer (Part Number 65) on screw (Part Number 88). Partially insert screw from inside the saddlebag. Locate a second washer (part number 65) from the hardware kit. Use a dab of silicone or a piece of tape and position the washer on the screw. The silicone or tape will secure the washer to the saddlebag in preparation for later steps when the bag assembly is attached to the vehicle. 6. See Figure. Obtain left hand support () with channel () and turn signal support () attached. 7. See Figure. Position support () on saddlebag () and push screw all the way through channel (). 8. Obtain screw (Part Number 9), washer (Part Number 65) and flange nut (Part Number 75) and secure bottom attachment bracket (, Figure ) of saddlebag to support. 9. Obtain screw (Part Number 8), washer (Part Number 66), and hex spacer (Part Number 99-00). Place washer on screw and insert from inside of the saddlebag (5, Figure ). Temporarily hold in place by screwing on hex spacer. 0. See Figure. Obtain left turn signal () assembled previously. Insert screws (not shown) (Part Number 9) and washers (not shown) (Part Number 65) from inside saddlebag, through support (), and through left turn signal bracket. Secure with flange nuts () (Part Number 75).. Repeat Steps through 0 for attaching the support to the right-hand saddle bag.. Left hand support. Channel. Turn signal bracket i00 i00 Figure. Left Hand Support. Support. Saddlebag. Channel. Bottom attachment bracket 5. Washer and screw. Left turn signal. Support. Flange nut () Figure. Support on Saddlebag Figure. Attach Turn Signal to Support 5 -J0890 of 9
5 i00 5 i005. Screw (). Strut cover. Nut. Upper shock mount 5. Hex bolt, inch i00 Figure 5. Removing Remaining Strut Hardware (000 Shown). Shock mount. Shock. Shock cover Figure 7. Reattach Shock i006. Spacer. Strut cover. Second hole location. screw () Install Saddlebag on Motorcycle When performing Steps through, completely perform procedures for one side before continuing to the opposite side. This will ensure fender will remain supported during installation.. Raise the rear wheel off the ground and support the vehicle securely. Remove the left and right lower shock bolts so the rear wheel can be lowered to create clearance when installing the saddlebag mounting bolts.. See Figure 5. Remove remaining screws () (from inside fender) securing strut cover () to fender models: Remove nut () holding upper shock mount (). 000 and later models: Remove screw and cover from top of shock. Remove strut cover. -J0890 Figure 6. Place Spacer Inside Strut Cover. Saddlebag assembly Figure 8. Position Saddlebag on Motorcycle. See Figure 6. Obtain spacer () (Part Number 579) and strut cover (). Install spacer on the inside of the strut cover on the second hole from rear of strut (). Hold in place with a dab of silicone or piece of tape. Reattach cover to strut using two screws () removed in Step 5. See Figure models: Apply Loctite (blue) to the shock mount bolt. Remove hex spacer temporarily attached to saddlebag in Step 9 and screw it onto shock mount (). Tighten to -5 ft-lbs (8-7 Nm). 000 and later models: Put shock cover () and shock mount () (Part Number 77-00) on top of shock (). Apply Loctite (blue) to shock mount. Tighten to -5 ft-lbs (8-7 Nm). Obtain hex spacer temporarily attached to saddlebag assembly in Step 9 and screw it onto shock mount. Tighten to -5 ft-lbs (8-7 Nm). 5 of 9
6 i See Figure 9. Tighten both screws () to 7-9 ft-lbs ( Nm) torque to attach saddlebag assembly to motorcycle. Use nut (not shown) (Part Number 809) held inside saddlebag to attach screw (). Use Loctite on threads. Torque to -5 ft-lbs (. -.8 Nm). Slip vinyl cap (part number 957-0) onto the exposed threads. 0. Route wiring harness from turn signal along bottom of strut and insert into retaining clips installed in Step. Bend clip tabs to hold wiring harness in place.. Tighten both screws. Screw with inside nut attached i0 Figure 9. Saddlebag Attached to Motorcycle. Boxed area of frame. Turn signal connector 6. See Figure 5. Remove the inch hex bolt (5) (part number 88) temporarily attached to the saddlebag in step 5. Insert bolt from the inside of the fender through the frame and fender strut in second hole from rear of strut as shown in Figure Add a drop of Loctite to threads of bolt that is inserted through the saddlebag at the front location. 8. See Figure 8. Position saddlebag assembly onto motorcycle. Figure 0. Route Wiring to Connector [7] (000 Shown). See Figure 0. Continue routing wiring harness under front of strut in front of fender and through middle boxed area of frame () to connector ().. Following instructions in Service Manual, install pin terminals to respective cavities in turn signal connector [7]. Final Installation Steps WARNING Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00069a). Connect battery cables, positive cable first.. Install seat. WARNING After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) WARNING Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (006a) 5. Check turn signals for proper operation. WARNING Keep tail lamp visible at all times. Do not place objects on license plate bracket blocking tail lamp visibility. Low visibility of rider can result in death or serious injury. (00a) 6. Check tail lamp for proper operation. -J of 9
7 Service Parts Part No Sportster Saddlebag Kit Date 0/05 i009 Mounting Bracket Kit Bracket, mounting right hand Bracket, mounting left hand Bracket, turn signal mounting right Bracket, turn signal mounting left J of 9
8 Service Parts Part No Sportster Saddlebag Kit Date 0/05 i00a Hardware Kit (957-00B) Screw hex socket button () 58 Screw, button socket head () 8 Screw, hex socket button head (6) 9 Screw, hex head () 88 5 Spacer () Washer, plain (0) 65 7 Washer, plain () 66 8 Lockwasher, hi collar () 70 9 Nut, flange locking (6) 75 0 Cable strap () 0065 Clip, adhesive (6) 00 Grommet () 7 Stud, shock mount () Polyurethane hole plug () Vinyl cap, thread cover, not shown () Hex nut, () not shown Harness, turn signal wire () Connector, sealed butt () Grommet (8) Spacer () A Spacer (8) A Spacer, hex Screw, 5/6x8x () 09 Spacer,.50 inch thick () Loctite (.5 ml) (not shown) J of 9
9 Service Parts Part No Sportster Saddlebag Kit Date 0/05 i057 5, , Saddlebag (Left) Part Number Saddlebag (Right) Part Number Saddlebag bottom, right hand Saddlebag bottom, left hand Saddlebag lid, right hand Saddlebag lid, left hand Reflector, red right hand Reflector, amber right hand Reflector, red left hand Reflector, amber left hand Plate, cam lock Keeper, latch Medallion, H-D Plate, lid hinge mount Plate, base hinge mount Plate, latch backing Cam, latch lever Latch assembly Hinge assembly J , 6 Cover, latch Lever, latch Lock assembly (set of ) Cam block Screw, #0-6x/ self tap (9) 5 Washer, non metallic Nut, keps #0- () 769 Screw, M6-6Hx5 () 96 Screw, # Washer, flat #8 68W 6 Screw, button head /-0x/ () 65 7 Gasket, lid Label saddlebag Plate, hinge cover Screw, button head /-0x/ 97 Gasket, lock () of 9
w w w. h d o n l i n e s h o p. d e LAYBACK LICENSE PLATE AND TURN SIGNAL RELOCATION KIT INSTALLATION GENERAL -J03892 REV Kit Number
-J0 REV. 00-0-0 LAYBACK LICENSE PLATE AND TURN SIGNAL RELOCATION KIT GENERAL Kit Number 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section
More informationINSTRUCTIONS. w w w. h d o n l i n e s h o p. d e SPRINGER AUXILIARY LAMP KIT 1WARNING -J03497 REV General.
INSTRUCTIONS -J097 REV. 0-0-00 Kit Number 6986-0A General Auxiliary/fog lamps are not included in this kit. The lamps must be purchased separately. HDI (International) motorcycles should only use approved
More informationw w w. h d o n l i n e s h o p. d e VRSC TURN SIGNAL RELOCATION KIT GENERAL INSTALLATION -J03341 REV Kit Number Models
-J0 REV. 006-06-6 GENERAL Kit Number 70-0 Models VRSC TURN SIGNAL RELOCATION KIT This kit fits 00 and later VRSCA, VRSCB, VRSCD, and VRSCDX model motorcycles. This kit is a necessary addition when installing
More informationDYNA OIL COOLER AND THERMOSTAT KIT
INSTRUCTIONS -J000 REV. 07-5-00 Kit Numbers 6985-0 (Chrome) and 6989-0 (Silver) General DYNA OIL COOLER AND THERMOSTAT KIT These oil cooler kits feature a thermostat built-in to the oil filter mount. These
More informationw w w. h d o n l i n e s h o p. d e ELECTRA-GLO LIGHT BARS GENERAL INSTALLATION -J04723 REV Kit Number Models Kit Contents
-J07 REV. 00-0-0 GENERAL Kit Number -09 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only). Kit Contents See
More informationw w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required
-J006 REV. 006-08- CRUISE CONTROL KIT GENERAL Kit Number 7796-07 Models For the most up-to-date model fitment information, please see the product label or www.harley-davidson.com. Additional Parts Required.
More informationw w w. h d o n l i n e s h o p. d e CHROME FAN KIT GENERAL INSTALLATION -J04347 REV Kit Number Models Kit Contents
-J0447 REV. 008-08-05 CHROME FAN KIT GENERAL Kit Number 996-08 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationw w w. h d o n l i n e s h o p. d e HEATED HAND GRIP KITS GENERAL REMOVAL -J02983 REV Kit Number Models Kit numbers Service Parts
-J098 REV. 007-0-0 GENERAL Kit Number 56047-0B, 5607-0B, 5674-0B, 5696-0B, 565-0B, 5669-0A, 56694-04A, 56750-04A, 5688-0A, 569-05, 5696-05, 56997-07 Models For model fitment information, please see the
More informationINSTRUCTIONS. w w w. h d o n l i n e s h o p. d e ENGINE GUARD-MOUNTED FOG LAMP KIT 1WARNING -J02798 REV Installation.
INSTRUCTIONS -J0798 REV. 9-4-00 Kit Number 689-98B General ENGINE GUARD-MOUNTED FOG LAMP KIT Installation This kit fits all models equipped with Harley-Davidson -/4 in. ( mm) diameter front engine guards,
More informationw w w. h d o n l i n e s h o p. d e ROAD KING FAT HANDLEBAR KIT GENERAL PREPARATION - ALL MODELS -J02375 REV Kit Number Models ABS Models
-J02375 REV. 2008--9 GENERAL Kit Number 56675-05 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only). ABS Models
More informationTEARDROP SPECIFIC-FIT
TEARDROP SPECIFIC-FIT SADDLEBAGS 3501-0461 3501-0462 FEATURES OF THE SADDLEMEN SADDLEBAGS: Quality luggage system that adds style and function to your motorcycle Bag shape and mounts specially built to
More informationROAD TECH ZUMO GLOBAL POSITIONING SYSTEM (GPS) HANDLE- BAR MOUNT KIT
-J046 REV. 008-08- ROAD TECH ZUMO GLOBAL POSITIONING SYSTEM (GPS) HANDLE- BAR MOUNT KIT GENERAL Kit Number 965-08 Models This kit is required when using a Road Tech Zumo GPS unit on specific model motorcycles.
More informationw w w. h d o n l i n e s h o p. d e STREET SLAMMER HANDLEBAR KIT GENERAL INSTALLATION -J03363 REV Kit Number Models Kit Contents
-J06 REV. 006-06- GENERAL Kit Number 69-0 Models STREET SLAMMER HANDLEBAR KIT Ask a Harley-Davidson dealer or refer to the latest Harley- Davidson Genuine Motor Accessories and Genuine Motor Parts catalog
More informationFREIGHT TRAIN HEADLAMP NACELLE KITS
-J09 0-08-8 FREIGHT TRAIN HEADLAMP NACELLE KITS GENERAL Kit Numbers 6000, 600 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of wwwharley-davidsoncom
More informationw w w. h d o n l i n e s h o p. d e BLACK HAND CONTROLS FOR DYNA AND SOFTAIL MODELS GENERAL INSTALLATION -J04155 REV Kit Number Models
-J0 REV. 00-08- BLACK HAND CONTROLS FOR DYNA AND SOFTAIL MODELS GENERAL Kit Number 709-07 (BLACK) Models This kit is designed for installation on 9 and later Sportster, Dyna, Softail, and Road King models
More informationINSTRUCTIONS FLHT 1998 AND LATER MODELS RADIO/CD KIT 1WARNING -J02911 REV General. Installation. Outer Fairing Removal
MPH CERTIFIED HARLEY-DAVIDSON UNLOCK RPMx00 HARLEY-DAVIDSON INSTRUCTIONS REV. 5--0 Kit Numbers 760-0A (Domestic) and 769-0A (HDI) General FLHT 998 AND LATER MODELS RADIO/CD KIT This radio kit fits 998
More informationw w w. h d o n l i n e s h o p. d e
-J008 REV. 00-09-07 REMOTE CONTROL GARAGE DOOR OPENER KITS GENERAL Kit Numbers 9558-0A (Transmitter/Receiver Kit), 956-0 (Transmitter Kit), 956-0 (Receiver Kit) Models For model fitment information, see
More information2004/2013 Harley Davidson Road Glide
2004/2013 Harley Davidson Road Glide VORTEX XMC-575OD SERIES SPECIFICATIONS 1. Warranty : Extended 2. Input Voltage : 12V 3. Modes : Low, High, Halo 4. LED Lifespan : 50,000 Hours WARNING: Due to excessive
More informationw w w. h d o n l i n e s h o p. d e ROAD TECH QUEST GLOBAL POSITIONING SYSTEM (GPS) MOUNTING KIT GENERAL INSTALLATION -J03554 REV.
-J03554 REV. 007-08-0 ROAD TECH QUEST GLOBAL POSITIONING SYSTEM (GPS) MOUNTING KIT GENERAL Kit Number 900-05 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories
More informationw w w. h d o n l i n e s h o p. d e CHROME SWITCH HOUSING KIT GENERAL HANDLEBAR SWITCH REMOVAL/INSTALLATION FXDWGI AND FXDBI MODEL TURN SIGNAL REMOVAL
-J00 REV. 00-07-9 GENERAL Kit Number 70-9B, 70-9B, 708-9C Models For the most up-to-date model fitment information, please see the product label or www.harley-davidson.com. See Table for items contained
More informationw w w. h d o n l i n e s h o p. d e TWO-INCH TACHOMETER KIT GENERAL INSTALLATION -J03991 REV Kit Number Models Kit Contents
-J0399 REV. 006-05- GENERAL Kit Number 67564-05A Models This kit fits: 004 and later FXD, FXDC, FXDX, and FXDWG 004 and later Softail (exept FLSTN) 004 and later FLHR/C 004 and later XL 006 and later FXDB
More informationw w w. h d o n l i n e s h o p. d e SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL INSTALLATION -J04480 REV.
-J080 REV. 2009-05-2 SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 292-08, 29080-09 Models For model fitment information, see the P&A Retail Catalog or the Parts and
More informationw w w. h d o n l i n e s h o p. d e CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT GENERAL INSTALLATION -J04405 REV Kit Number Models
-J005 REV. 008-09-0 CHROME.5 INCH (.75 MM) DIAMETER HANDLEBAR KIT GENERAL Kit Number 560-08 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com
More informationRUN/BRAKE/TURN AUXILIARY LIGHTS J
RUN/BRAKE/TURN AUXILIARY LIGHTS J06236 2018-05-31 GENERAL Kit Numbers 67800589A, 69202276 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harleydavidson.com
More informationw w w. h d o n l i n e s h o p. d e DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT GENERAL INSTALLATION -J00325 REV Kit Number Models
-J00 REV. 00-- DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT GENERAL Kit Number -A, 0-, -, 0-, -, - 0, -0 Models These kits fit and later FXST, FXSTB, FXSTC, and and later FXDWG Harley-Davidson model
More informationw w w. h d o n l i n e s h o p. d e SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL INSTALLATION -J04479 REV.
-J04479 REV. 008-- SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 95-08A, 9006-09A Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationUNPACK AND IDENTIFY THE FOLLOWING PARTS.
SUT-350-AIT ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first
More informationSCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT
-J04479 REV. 009-06-0 SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 95-08A, 9006-09A, 876-0 Models For model fitment information, see the P&A Retail Catalog or the Parts
More informationUNPACK AND IDENTIFY THE FOLLOWING PARTS.
SUT-250-M2 ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first
More informationMULTI-FIT BRAIDED THROTTLE/IDLE CABLE KITS
-J08 REV. 008-08-5 MULTI-FIT BRAIDED THROTTLE/IDLE CABLE KITS GENERAL Kit Numbers Stainless Steel Kits 560-0 56-00 56-0A 565-0A 5650-0A 5670-0A 567-0A 567-0A 5678-0 569-0 5699-05 5656-0 56579-0A 5670-0
More informationR O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP
R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer
More informationDETACHABLE QUARTER FAIRING AND DOCKING HARDWARE KIT
INSTRUCTIONS -J09 REV. 0--00 Kit Numbers 7070-98 (primed kit) DETACHABLE QUARTER FAIRING AND DOCKING HARDWARE KIT General This kit is for installation on 988 and later XL, FXR and FXD model motorcycles
More informationINSTALLATION LIGHTED CURVED LAY DOWN LICENSE PLATE MOUNT 3166
INSTALLATION LIGHTED CURVED LAY DOWN LICENSE PLATE MOUNT 3166 PARTS INCLUDED 1 Lighted Curved Lay Down License Plate Assembly 1 Hardware Kit Including: 6 Cable Ties 1 Dielectric Grease Pack 1 1 x 8 Tape
More informationw w w. h d o n l i n e s h o p. d e DYNA FORWARD CONTROL KIT GENERAL INSTALLATION -J03509 REV Kit Number Models Additional Parts Required
-J009 REV. 00-09- GENERAL Kit Number 900-0A Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English only). Additional
More informationI. Before starting installation
5. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. A. Disconnect battery cables 1. Disconnect the negative cable first, then the
More informationUNPACK AND IDENTIFY THE FOLLOWING PARTS.
SUT-500-S ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first
More informationInstallation Instructions Harley-Davidson Saddlebag Lids
Installation Instructions Harley-Davidson Saddlebag Lids Thank you for your purchase of Bagger Audio Saddlebag Lids for your Harley- Davidson motorcycle. We have carefully engineered these products to
More informationAirtail I.A.S. Suspension System for Harley Davidson
5572 Fresca Drive, La Palma, CA 90623 714.523.8700, FAX 714.523.3220 Airtail I.A.S. Suspension System for Harley Davidson Compressor Kit Installation Instructions FLH/FLT Models with and without Cruise
More information2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014
2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 125 Industrial Drive Spearfish, SD 57783 Toll Free 888.3WHEELS w w w. l e h m a n t r i k e s. c o m UNDERSTANDING SAFETY LABELS &
More informationCHEVORLET IMPALA
1962-64 CHEVORLET IMPALA Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 1 deck lid harness 4 grommets 1 power wire 2 pigtail harness kits 2 crimp terminal kits PN
More informationw w w. h d o n l i n e s h o p. d e MODULAR DIAMONDBACK BRAKE LINE KITS GENERAL -J04284 REV Kit Number Models Tools and Supplies Required
-J08 REV. 007-07-6 GENERAL MODULAR DIAMONDBACK BRAKE LINE KITS Table. Upper Brake Line s (Banjo Angle 0 - Straight) 7-07 77-07 79-07 8-07 87-07 9-07 8-07 8 inch 9 inch 0 inch inch inch inch inch 96-07
More informationw w w. h d o n l i n e s h o p. d e DETACHABLE WINDSHIELD KITS GENERAL INSTALLATION -J04501 REV Kit Number Models Kit Contents
-J00 REV. 007-06-0 GENERAL Kit Number 88-08 and 788-08 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English only).
More informationCRUISE CONTROL (FLHRC, FLHTCU, FLTR) 8.31
CRUISE CONTROL (FLHRC, FLHTCU, FLTR) 8.31 GENERAL f1368a8x The Cruise Control system provides automatic vehicle speed control. The electronics and stepper motor are contained in a control module mounted
More informationR O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP
R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer
More informationSUT-250-S (These instructions are used for SUT-250-SCLC also)
SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16,
More informationInstallation Instructions For Lloydz Motorworkz Billet Air Cleaner Kit for Victory Motorcycles
Instruction 106-6005 9-1-09 25 Railroad Ave PO Box 11 Pine Bush, NY 12566 Installation Instructions For Lloydz Motorworkz Billet Air Cleaner Kit for Victory Motorcycles Kit Contents: Billet backplate Qty
More informationSTABILIZER LINKS 2.21
STABILIZER LINKS. GENERAL The stabilizer link system allows the engine to float on its rubber engine mounts while maintaining engine-to-frame alignment. The stabilizer links provide a fixed alignment,
More informationINSTRUCTIONS SOFTAIL 6 SPEED TRANSMISSION - COMPLETE 1WARNING -J03479 REV General. Removal of Original Transmission
INSTRUCTIONS REV. 10-13-2005 Kit Numbers 330-03A, 33045-03A General SOFTAIL 6 SPEED TRANSMISSION - COMPLETE These kits fit 2000 and later carbureted and 2001 and later EFI Softail model motorcycles. Requires
More informationSUT-450-I ASSEMBLY REQUIREMENTS
SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt
More informationCurrent. Installation Instructions
by Trike Conversion Kit 2004 - Current Harley-Davidson Sportster Installation Instructions REVISED 4-2017 California Sidecar Parts & Technical Support 434.263.8866 Table of contents: 1. Warnings and Considerations
More informationRT1 SLIP-ON EXHAUST HONDA CBR600RR REV. A
08-50-43733 REV. A PARTS INCLUDED Ref. Part Number Description Qty 1) 00-200-00064 Slip-on S-bend Assembly 1 2) 00-200-00088 RT1 Aluminum Muffler Assembly 1 3) 03-46-43058 Muffler Mounting Strap 1 4) 07-27-42566
More informationINSTALLATION INSTRUCTIONS DODGE DAKOTA 2 KIT # 682 (2WD), 692 (4WD) 3 KIT # 683 (2WD), 693 (4WD)
INSTALLATION INSTRUCTIONS 1997-1999 DODGE DAKOTA 2 KIT # 682 (2WD), 692 (4WD) 3 KIT # 683 (2WD), 693 (4WD) Installation of a Performance Accessories body lift kit will change the vehicle s center of gravity
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationHEATED HAND GRIP KIT
-J0596 REV. 00-- HEATED HAND GRIP KIT GENERAL Kit Number 56000 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationProgressive Suspension Airtail I.A.S.
5572 Fresca Drive, La Palma, CA 90623 714.523.8700, FAX 714.523.3220 Progressive Suspension Airtail I.A.S. Installation Instructions for Harley Davidson E.C.C. with Compressor Kit FLH/FLT Models with and
More informationRT1 DUAL OUTLET SLIP-ON EXHAUST HONDA CBR600RR Rev B
18-1022-723-02 08 50 44541 Rev B PARTS INCLUDED Ref. Part Number Description Qty 1) 00-200-00042 Slip-on S-bend Assembly 1 2) 00-200-01197 Stainless Steel Dual Outlet Muffler 1 3) 03-46-42766 Muffler Mounting
More informationGL1800 TRAILER HITCH - INSTALLATION INSTRUCTIONS #GL
GL1800 TRAILER HITCH - INSTALLATION INSTRUCTIONS #GL18007-20 Read through these instructions completely before attempting installation, lay out all pieces including the numbered hardware bags to familiarize
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRUNK INSTALLATION KIT P/N 08L73-MKC-A10ZA Application GL1800B/BD Honda Dealer: Please give a copy of these instructions to your customer. Publication No. MII 16426
More informationLittleGiant Trailer Harley Hauler Kit
3380 N. El Paso St., Colorado Springs, CO 80907 LittleGiant Trailer Harley Hauler Kit User Assembly Manual Visit our website at www.letsgoaero.com For Assistance, please call 1-877-464-2376 or 719-630-3800
More informationINSTRUCTIONS SCREAMIN EAGLE FLHT 6-SPEED TRANSMISSION 1WARNING -J03322 REV Installation. General. Prepare the Motorcycle for Service
INSTRUCTIONS REV. 02-11-2005 Kit Number 33136-04 and 33137-04 SCREAMIN EAGLE FLHT 6-SPEED TRANSMISSION General The Screamin Eagle FLHT 6-Speed Transmission kit fits 2002 and later Harley-Davidson Touring
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationBOOM! AUDIO CRUISER AMP AND SPEAKER KIT - WINDSHIELD MOUNT
-J0 0--0 BOOM! AUDIO CUISE AMP AND SPEAKE KIT - WINDSHIELD MOUNT GENEAL Kit Number -09A Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com
More informationCobra & Cobra XL. Trike Conversion Kit GL1800 Goldwing. Installation Instructions. California Sidecar Parts & Technical Support
Cobra & Cobra XL by Trike Conversion Kit 2001-2010 GL1800 Goldwing Installation Instructions REVISED 1-2015 California Sidecar Parts & Technical Support 434.263.8866 Table of contents: 1. Maintenance Schedule
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE GATOR HPX and/or XUV HARD SIDED CAB ENCLOSURE (p/n: 1GTR44AS) SOFT SIDED CAB ENCLOSURE (p/n: 1GTR44SS) 111 HIGGINS STREET, WORCESTER,
More informationAccessory Fuse Block. Please read this entire manual before proceeding with installation.
Accessory Fuse Block Please read this entire manual before proceeding with installation. Kit Components: (1) Fuse Block Assembly (1) Harness (1) Positive power cable (1) Negative power cable (5) Pigtails
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationTwo panel Sequential LED Taillight kit installation guide
1970 CHEVELLE Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 2 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2883261 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationI N S TA L L AT I O N
I N S TA L L AT I O N 5008 fits: H-D: '80-Up Electra glide, tour glide, road king, road glide or street glide PartS Included 1 Right Fork Mount Assembly 1 Left Fork Mount Assembly 2 H3 Driving Light Assemblies
More information2015+ Mustang Rear Valance Installation Instructions P/N: (R F953) (R F953BS)
2015+ Mustang Rear Valance Installation Instructions P/N: 421894 (R1315-17F953) 421919 (R1315-17F953BS) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang Rear Valance Kit Installation
More informationIGNITION/HEADLAMP SWITCH
IGNITION/HEADLAMP SWITCH DO NOT modify the ignition/headlamp switch wiring to circumvent the automatic-on headlamp feature. Visibility is a major concern for motorcyclists. Failure to have proper headlamp
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SADDLEBAG MOUNTING Application Publications No. Mll 13304-13660 BRACKET After 2007 VT750C Issue Date P/N 08L56-MEG-100E Revised: April 2011 Honda Dealer: Please give
More informationINSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT
PART NUMBER: 0000-89-N30 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT APPLICABLE MODELS: 2016 > CX-9 PACKAGE CONTENTS: INSTALLATION INSTRUCTIONS QTY 1 CABLE TIE MOUNT QTY
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationINSTALLATION ZOMBIE L.E.D. FUEL & BATTERY GAUGE. THANK YOU FOR CHOOSING KϋRYAKYN!
THANK YOU FOR CHOOSING KϋRYAKYN! PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND PROPERTY DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS, AND NOTICES REGARDING THE, USE,
More informationSuspension System RS6582B
Suspension System RS6582B Tahoe/Yukon READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance
More informationINSTRUCTIONS DYNA FLOORBOARD KIT 1WARNING -J01921 REV General. Kit contents. Installation SHIFTER ASSEMBLY (LEFT SIDE) Kit Number
General INSTRUCTIONS REV. 10-1-200 Kit Number 50601-01 DYNA FLOORBOARD KIT Kit contents This forward foot controls kit is designed for use on all 1996 and later FXD models and includes all parts required
More informationTrike Conversion Kit GL1500 Goldwing
BY Trike Conversion Kit 1988-2000 GL1500 Goldwing Installation Instructions Revised 3-2018 California Sidecar Parts & Technical Support 434.263.8866 Table of contents: 1. Maintenance Schedule 5 2. Disassembly
More informationC15C C15C. Page 1 of 20
2 x Lid Front Hinge 1135 8 x M8 Bolt 8 x M8 Washer (3mm Thick) 4 x M6 Large washers 4 x M6 Spring washers 4 x M6 x 40mm Bolts 6 x M6 20mm Bolts 6 x M6 Washers 20 x Screws 2 x Lid mount gas strut bracket
More informationInstallation Instructions QUICKSILVER CONSOLE SHIFTER Fits: Chevelle / El Camino
WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with the engine turned off. Place blocks or wedges in front of and behind both rear wheels to prevent movement in
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationPart Number: TTU-BGB14-DRL TTU-BGP14-DRL
11/15/16 TOYOTA TUNDRA 2014-17 Billet Grille w/led DRL Part Number: TTU-BGB14-DRL TTU-BGP14-DRL Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Switch 4 1 User Card 5 2 Hardware
More informationPONTIAC FIREBIRD
1974-78 PONTIAC FIREBIRD Two Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 2 LED panels 2 LED panel mount kits 6 rubber grommets 1 power wire 1 pigtail harness Kit 1 crimp terminal
More informationINSTALLATION TRUE DUAL HEADPIPES 497
TRUE DUAL HEADPIPES 497 PARTS INCLUDED 1 Front Head Pipe 1 Rear Head Pipe 1 Front Heat Shield 1 Rear Heat Shield 1 Bracket (stamped 422-P) 1 Bracket (stamped 423-P) 2 1/2 x 1-1/4 Socket Head Cap Screw
More informationInstallation instructions, accessories - Rear Seat Entertainment
XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 2004 10 XC90 2003, XC90 2004, XC90 2005, XC90 2006, XC90 2007, XC90 2008 Replaces issue: 2003 12 J3904620 Page 1 of 18 Required tools A0000162 A0000163
More informationHarley-Davidson Dyna large saddlebags installation guide
ends@endscuoio.it www.endscuoio.com Harley-Davidson Dyna large saddlebags installation guide Summary Intro... 3 Compatibility... 3 Brackets... 3 Advice... 3 Video... 3 Installation... 4 Superglide, Wide
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More informationMAZDA BT-50 (October 2011 Production Onwards) 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS
MAZDA BT-50 (October 0 Production Onwards) & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS Installation Time: Approx. 0 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent
More information2015 Ford F150 Front Bumper w/ LED
PARTS LIST: 2015 Ford F150 Bumper w/ LED 1 Bumper Assembly 4 8mm Lock Washers 1 Driver/left L Bracket (center LED light) 2 8mm Hex Nuts 1 Passenger/right L Bracket (center LED light) 2 6mm x 20mm Button
More informationUT ASSEMBLY REQUIREMENTS. *Torque all T-bolt nuts to foot pounds.
UT-1000-8-04 ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after
More informationR O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP
R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer
More informationAvoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket.
HOUSINGS 7808 Thank You For Choosing Küryakyn! Protect yourself and others from potential injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding
More informationB-026INT October 6, 1999 FUEL FILTER BRACKET RETROFIT (JAPAN ONLY) GENERAL RETURN THIS TO: INITIAL HERE TECHNICIAN NO.
5 SERVICE BULLETIN B-026INT October 6, 1999 FUEL FILTER BRACKET RETROFIT (JAPAN ONLY) GENERAL It has come to the attention of Buell Distribution Corporation that a certain number of 2000 Model X1 and S3/T
More informationINSTRUCTIONS OIL COOLER KIT 1WARNING -J00715 REV General. Kit Number B and B
INSTRUCTIONS -J00715 REV. 4-24-00 Kit Number 62571-77B and 62577-77B General This Oil Cooler Kit is designed for: 1981 and Earlier XL 1982 and Later FXR 1984-1999 FXST 1986-1999 FLST including FLSTF Fat
More informationParade Flag Holder or Quick Detach Rack Mounting Kit For 2009 and Newer Harley-Davidson FLH, FLHX & FLT Models Part # HWK020
Parade Flag Holder or Quick Detach Rack Mounting Kit For 2009 and Newer Harley-Davidson FLH, FLHX & FLT Models Part # HWK020 Note: On 2009 thru 2013 models proceed as follows. On 2014 and newer models,
More informationHIGH FLOW COLD AIR INTAKE SYSTEM INSTALLATION INSTRUCTIONS D , D A
HIGH FLOW COLD AIR INTAKE SYSTEM INSTALLATION INSTRUCTIONS D760-0320, D760-0320A 1992-95 325i, is 1995 M3 (3.0L) Parts List: 1 Intake Tube 1 Silicone Hose 1 Air Flow Meter Bracket 1 Hose Clamp (#36z) 1
More informationINTAKE AIR TEMPERATURE SENSOR (IAT)
INTAKE AIR TEMPERATURE SENSOR (IAT) 4.8 Refer to the ELECTRICAL DIAGNOSTIC MANUAL for information on the function and testing of the intake air temperature sensor (IAT sensor). sm054 To prevent accidental
More informationSUM Chevy Truck frame mount booster kit
SUM-760211 1955-1959 Chevy Truck frame mount booster kit Unboxing your kit: 1. Remove new booster, bracket assembly and master cylinder from their boxes and inspect the parts. 2. New boosters come with
More informationINTEGRATED1500LB WINCH KIT
INTEGRATED1500LB WINCH KIT P/N 2882798 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More information