8200 LED YOKE MOUNT MOUNTING ACCESSORIES

Transcription

1 INSTLLTION INSTRUTIONS. e sure the power is off at Yoke ccessories. 2. Install the mounting accessory in the desired location using appropriate fasteners (by others). Mounting accessory sold separately. 3. Mount the fixture yoke to the accessory using the supplied cord seal fastener (included with mounting accessory). 4. Route fixture cord through cord seal fastener and tighten seal nut. Make all wiring connections to the fixture within the mounting accessory splice compartment. NOT: Make sure that there is enough cord left free for aiming of the fixture. 5. Remove the two (2) outer cover caps from the fixture yoke. Loosen the locking nuts and aim the fixture as required. Retighten the locking nuts securely and replace cover caps. 6. Open the fixture lens door by loosening the two (2) cover screws. Install the proper lamp (see inside fixture label). lose the lens door and retighten the two (2) cover screws securely. (Lamp sold separately). 7. Supply proper power to the fixture L YOK MOUNT SSORY MOUNTIN electrician in accordance with the National lectrical ode MOUNTIN SSORIS Yoke Mount ixture. ixture ord 2. Yoke Mount 3. Yoke over aps 4. Locking Nuts and Washers (2) 5. Lens oor Mounting ccessory (reference only) 6. Splice over 7. Splice ompartment ord Seal astener ssembly (reference only) 8. ord Seal astener ody 9. Lock Nut & Washer, ottom (not shown) 0. Lock Nut with Set Screws, Top. rommet ord Seal 2. ord Seal Nut 203 cuity rands Lighting, Inc. ny dimension on this sheet is to be assumed as a reference dimension: inspection requirements. (NSI Y ) 944 eering ve, 2nd loor hatsworth, 93

2 INSTLLTION INSTRUTIONS 8200 L YOK MOUNT MOUNTIN SSORIS SSORY MOUNTIN electrician in accordance with the National lectrical ode 8 (470) 6 (52) 203 cuity rands Lighting, Inc. ny dimension on this sheet is to be assumed as a reference dimension: inspection requirements. (NSI Y ) 944 eering ve, 2nd loor hatsworth, 93

3 INSTLLTION INSTRUTIONS. e sure the power is off at Junction ox. (Junction ox sold separately). 2. Install the remote junction box with cord seal in the desired location using appropriate fasteners (by others). Junction box and cord seal sold separately. 3. Mount the fixture yoke in the desired location using appropriate fasteners (by others). See attached mounting template. 4. Route the fixture cord to the remote junction box and through the cord seal. Tighten the cord seal outer nut. Make all wiring connections to the fixture within the junction box splice compartment. NOT: Make sure that there is enough cord left free for aiming of the fixture. 5. Remove the two (2) outer cover caps from the fixture yoke. Loosen the locking nuts and aim the fixture as required. Retighten the locking nuts securely and replace cover caps. 6. Open the fixture lens door by loosening the two (2) cover screws. Install the proper lamp (see inside fixture label). lose the lens door and retighten the two (2) cover screws securely. (Lamp sold separately). 7. Supply proper power to the fixture L YOK MOUNT SUR MOUNTIN electrician in accordance with the National lectrical ode JUNTION OX Yoke Mount ixture. ixture ord 2. Yoke Mount 3. Yoke over aps 4. Locking Nuts and Washers (2) 5. Lens oor Remote Junction ox (reference only) 6. Splice over 7. Splice ompartment ord Seal ssembly (reference only) 8. ord Seal ody 9. rommet ord Seal 0. ord Seal Nut 203 cuity rands Lighting, Inc. ny dimension on this sheet is to be assumed as a reference dimension: inspection requirements. (NSI Y ) 944 eering ve, 2nd loor hatsworth, 93

4 8200 L YOK MOUNT YOK TMPLT (NOT TO SL) INSTLLTION INSTRUTIONS electrician in accordance with the National lectrical ode 2 /2 (64) 3/8 (35) 7/8 (22) enter Mount Hole (ccessory Mounting) 2 3/4 (70) 5 (27) 7/6 (6) Thru Holes 2 Places 3/8 olts (y Others) Two (2) Mounting Holes Tap for 3/8-6 asteners (y Others) 203 cuity rands Lighting, Inc. ny dimension on this sheet is to be assumed as a reference dimension: inspection requirements. (NSI Y ) 944 eering ve, 2nd loor hatsworth, 93

5 8200 L STY L INSTLLTION INSTRUTIONS electrician in accordance with the National lectrical ode. Mount 8200 L fixture per installation instructions for the type of fixture mount provided. 2. ttach free end of safety cable to mounting surface using appropriate fastener (by others) for the mounting surface material. Note: Safety cable has a 600 lb. static load capacity (minimum load rating). oth mounting surface and safety cable fastener (by others) must meet this minimum load rating. STY L - YOK MOUNT 800 Yoke Mount ixture ixture ord Yoke Mount Yoke over aps Locking Nuts and Washers (2) Lens oor Safety able STY L - WM Wall Mount racket ixture & Mount ixture Wires asteners (by others) not shown. onduit (by others) Splice over & Screws Safety able 203 cuity rands Lighting, Inc. ny dimension on this sheet is to be assumed as a reference dimension: inspection requirements. (NSI Y ) 944 eering ve, 2nd loor hatsworth, 93