Carousel Unit User Manual Replacing the Check Stand Motor
|
|
- Bertina Hardy
- 5 years ago
- Views:
Transcription
1 Carousel Unit User Manual Replacing the Check Stand Motor 02/01/2017 1
2 Table of Contents Tools:... 3 Turn Off Power to the Unit:... 4 Remove Power Switch... 5 Remove Electric Eyes:... 6 Remove POS (Point-Of-Sale) Assembly:... 7 Remove & Replace Motor:... 9 Remove and Replace the Capacitor: Re-assemble the Unit Check the Belt Alignment: CONTACT INFORMATION
3 Tools You Will Need: 1. Power driver with a Phillips bit, special bit, and 7/16 socket 2. Flat head screwdriver 3. Wire cutters 4. 1/8 zip ties The image below shows the Belted, Carousel Check Out Stand. This instruction will demonstrate how to remove and replace the motor and capacitor. A new capacitor will be included with the new motor; thus, it will be necessary to replace the capacitor simultaneously with the motor. 3
4 Turn Off Power to the Unit: 1. Remove two screws holding the access panel on the customer s side of the Belted Lead-In. 2. Remove the access panel, exposing the Main Power Cord. Unplug the cord from the Power Pole. NOTE: Retain all hardware for later re-installation. 4
5 Remove Power Switch 1. Remove two screws holding the Power Switch on the clerk s side of the Belted Lead-In. Gently pry up and pull out the switch. 2. Use the blade of a flat head screwdriver to carefully separate the Belt Switch Plate from the wires. 3. Use caution to avoid damaging the wires. 5
6 Remove Electric Eyes: 1. Both the Sender and Receiver Eyes may be removed using the same steps, which follow. Remove two screws and pull out the Electric Eye casing (receiver shown). 2. Push the cable from underneath the unit rather than pulling on the wires, which could damage the Molex connector. 6 02/01/2017 Rev-
7 Remove POS (Point-Of-Sale) Assembly: 1. Inside the hardware package provided is a special bit required to remove the POS Assembly. 2. Using a power driver with the special bit, remove four bolts holding the POS Assembly to the rail (two on the front and two on the back). Lift and remove the POS Assembly. Set aside. 7
8 3. Unscrew and remove the stainless-steel trim rails from both the customer s and cashier s sides of the unit. 8
9 Remove & Replace Motor: 1. Remove the two screws at the bottom of the nose cover. 2. Pull up on the nose cover. There may be a tight fit; if so, lift up, pull back and lift up again. 9
10 3. The edges of the nose cover are slotted to connect to screws on the inside of each rail. 4. Using a power driver with a Phillips bit, remove the two screws holding the Dead plate. Remove the Dead plate. 10
11 5. Using a power driver with a Phillips bit, remove the four screws holding the Dead Plate Support, indicated by the red arrows below. 6. After removing the four screws, lift the Dead Plate Support out and away. 11
12 7. Use a power driver with a 7/16 socket to remove the two belt adjustment bolts located at the nose end of the unit. 8. Use the blade of a flat head screwdriver to lift the belt. 9. The belt plates are located underneath the belt. 12
13 10. There are finger slots in the corners of each belt plate. Use these to lift and remove the belt plates from the unit. 11. Note that the belt plates are held in place by the belt plate hooks. 12. Carefully lift the motor cylinder up and slide the belt away. 13
14 13. Replace the cylinder, being careful not to damage the Electric Eye wires. 14. Pull the belt back toward the nose of the unit and leave it folded and out of the way while performing the following steps. 14
15 15. Trace the motor cable to the capacitor. Reach underneath the Capacitor Housing and disconnect the cable. The four-pronged connector has a hook that must be pressed before it can be removed. 16. Dislodge the motor cable from the cable holders and remove the motor. 15
16 17. Obtain a new Motor Cylinder. Feed the motor cable through the opening in the mounting slots so that the cable may be attached to the cable holders and the Controller. 16
17 18. Slide the belt around the Motor Cylinder at the front end of the unit. Lay the Motor Cylinder back into its mounting slots. 19. Use caution when seating the Motor Cylinder to avoid damaging the Electric Eye cables. Ensure that the notch on the end of the Motor Cylinder is oriented on the customer s side of the unit and is facing downward. NOTCH MUST FACE DOWNWARD. 17
18 Remove and Replace the Capacitor: 1. Disconnect the three additional cables that are attached to the side of the Capacitor Housing. The black cable with two wires is the switch cable. The gray cables with two and four wires are both for the electric eyes. 2. Using a power driver with a Phillips bit, remove the small screw holding the Capacitor Housing to the base. Retain all hardware. 18
19 3. Grasp and pull the Capacitor Housing free from the base. 4. Remove the four screws from the bottom of the Capacitor Housing. Open the Housing to expose the Capacitor. Retain all hardware. CAPACITOR 19
20 5. Using wire cutters, sever the zip ties that hold the Capacitor in place 6. Use the blade of a flat head screwdriver to release the female quick disconnects attached to the Capacitor. 7. Obtain the new Capacitor and reconnect the wires from the previous step. Ensure that the wires are connected on opposite corners, as shown below. 20
21 8. Return the Capacitor to the Housing and secure in place using 1/8 zip ties. 9. Close the Housing and reinstall the four screws removed in Step Plug the Capacitor Housing back into the base. Replace the screw removed in Step 3. 21
22 11. Reconnect the electric eye and switch cables to the Capacitor Housing. The switch cable goes in the top position, followed by the 2-wire and 4-wire electric eye cables. 12. Reconnect the motor cable to the underside of the Capacitor Housing. 22
23 Re-assemble the Unit 1. Re-install the two belt plates onto the belt plate hooks along the sides of the unit. Straighten the belt so that it lays flat over the belt plates. 2. Re-install the Dead Plate Support and the Dead Plate in the same manner that they were removed in Steps 4 6. Be sure to replace the Dead Plate Support first. 23
24 3. Replace the stainless-steel trim along the unit rails. Feed the Power Switch cable through the opening in the trim and re-connect the Power Switch. 4. Attach the Power Switch to the rail using the two screws removed in Step 1 on Page 5. Before tightening, ensure the switch is oriented so that it is legible from the cashier s position. 24
25 5. Replace and tighten all of the remaining trim screws. 7. Re-attach the Electric Eyes to the unit using the screws retained at removal. Be careful not to strip the screws. 6. Replace the Electric Eyes by feeding the wires through the slots. Do not pull or tug on the wires, as they may become damaged. 25
26 8. Re-install the two belt adjustment bolts into the nose end of the unit. Use a 7/16 socket to tighten the belt. It is necessary to tighten each side just a bit at a time so that the belt is tightened evenly. 9. Re-connect the power cord to the power pole to restore power to the unit. 26
27 Check the Belt Alignment: 1. Turn on the belt power and check each of the corners to ensure that the belt is not touching the side rails. 2. When the automatic time-out causes the belt to stop, you can break the plane of the Electric Eyes to start the belt again. 3. To extend the running time of the belt while making adjustments, open the Lead-In s access panel and locate the Controller Assembly. 27
28 4. A button marked Test Run is located next to the LED light. Pressing this button will cause the belt to run for longer than two minutes. 5. If it is necessary to adjust the belt, use the adjustment bolts located at the nose end on the customer s side and cashier s side. 28
29 6. Use a 7/16 socket wrench to make adjustments. Adjusting the bolt left will loosen the belt tension and cause the belt to drift toward the side you are adjusting. Adjust the bolt to the right, the belt tension increases and causes the belt to drift away from the adjustment side. 7. After making an adjustment, allow belt to run at least five (5) minutes before making further adjustments so as not to overadjust the belt. 8. Re-install the nose cover and screws. Replace Lead-In access panel. 29
30 9. Re-install the POS onto the rail and secure using the four bolts removed in Step 2 on Page 7. Recall that these bolts will require the special bit included in the hardware package. CONTACT INFORMATION: If you have any questions about the contents of this instruction sheet, please do not hesitate to contact us. Your Royston Customer Service Team is ready to help you Replace Check Stand Motor 02/01/
Replacing a Load Cell in the 400 Series Force Plate
Replacing a Load Cell in the 400 Series Force Plate Determining which load cell is faulty You will first need to determine which load cell is at fault. To do this you will need the XPV7 diagnostic software.
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationDesktop 5.5 Z Axis Retrofit
Page 1 Kit parts Desktop 5.5 Z Axis Retrofit Carriage plate with stop bolt and Z proximity switch installed Zip ties Spare bolts Spindle mounting plate with stop bolt, spring mount, and rail Z proximity
More informationM7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301
M7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301 M7 Speed engineers and manufactures the highest quality MINI COOPER accessories and performance parts available anywhere on Planet Earth! Please
More informationSupply Valve Replacement
This procedure is to help facilitate the replacement of the25.1-25.4 supply valves. Solenoid Supply Valves Note: You will need the following tools: Socket Wrench with extension and a 3/8 Socket Size 1
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit was designed for a standard single pump Radium Engineering
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit wasn t designed for a FST-R, but can be accomplished. 1.
More informationRear Bumper Cover Unpainted ( ):
Rear Bumper Cover Unpainted (1999-2004): Tools Required: Ratchet Socket extension 7/16 deep well socket 7/16 wrench 5/16 socket Fastener Removal Tool Offset Phillips screwdriver Extendable magnet (optional
More informationReplacing the Gear Drive Motor Assembly and GFCI Module for Operation with the Chain Drive Motor Assembly
Replacing the Gear Drive Motor Assembly and GFCI Module for Operation with the Chain Drive Motor Assembly Kit Contents B00009035-3 Motor Drive Assembly (Return original to CMI) B00007698-8 GFCI Module
More informationINSTALLATION INSTRUCTIONS
1. Note: It is recommended this install be done with a minimal amount of fuel in the tank. This will reduce fuel spills and make installation easier and safer. Draining the tank is recommended. INSTALLATION
More informationiphone 5s Front Panel Replacement
iphone 5s Front Panel Replacement Replace the cracked or broken screen on your iphone 5s. Note: DIY at your own risk. New beginner must be careful, screens got problems mostly due to wrong installation
More informationLEXUS GX TOWING HITCH Preparation
LEXUS GX460 2014 - TOWING HITCH Preparation Part Number: PT228-60140 Kit Contents Item # Quantity Reqd. Description 1 1 Hitch Assembly 2 1 Wiring Harness Bracket 3 1 Hardware Bag 4 1 Hitch Cover 5 2 Center
More information5 Removal and replacement
5 Removal and replacement This chapter describes the removal and replacement of field-replaceable units (FRUs) only. Removal and replacement strategy User-replaceable parts Covers Internal assemblies ENWW
More informationInstallation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA
Installation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA1812510 Background: Early production Martin Yale Model 1812 Folders were originally equipped with a spring-clutch type feed
More informationSADDLEBAG AUDIO WIRE HARNESS KIT P/N
SADDLEBAG AUDIO WIRE HARNESS KIT P/N 2880986 APPLICATION ALL INDIAN MOTORCYCLES WITH BOTH TRUNK AND SADDLEBAG AUDIO INSTALLED BEFORE YOU BEGIN Read these instructions and check to be sure all parts and
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 2563000 Parts List 1 Carrier weldment 2 Support arm assembly 1 Third brake light assembly 1 Light extension bracket 1 Spare tire adjustment plate 1 Spare tire mount plate 1 Female spade
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
More informationCVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing
CVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing Tools Needed: 1/2 inch Socket Wire Cutters 7/16 inch Socket Wire Strippers 5/16 inch Socket Phillips Screwdriver 1/2 inch
More informationMaintenance Information
Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard
More informationToggle Button Kit. Installation Instructions MK5 / MK6 Golf, MK5 Jetta
Toggle Button Kit Installation Instructions MK5 / MK6 Golf, MK5 Jetta Thank you for choosing the Double Apex Toggle Button kit. If you have any questions about the installation please do not hesitate to
More informationZeon Control Pack Relocation Kit 78 Cable Length
ORIGINAL INSTRUCTIONS SYMBOL INDEX SYMBOL EXPLANATION SYMBOL EXPLANATION Read All Product Literature Always Wear Leather Gloves Always Wear Hearing and Eye Protection Do Not Move People Zeon Control Pack
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: R42H (2011) PART NUMBER: 999F3 AW000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description Service
More informationSection 5: Parts Replacement
Section 5: Parts Replacement Should the STAR TRAC 4500 Treadmill experience a problem requiring replacement of a specific part, the following procedures will help and instruct in the replacement of major
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More informationINSTALLATION INSTRUCTIONS
9002-6513 Rear Vision System W/ Zoom Aftermarket and Factory 8.4 Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 2012 RAM (Part B) 2013 Current RAM (Part A) NOTE:
More informationINSTRUCTIONS FOR INSTALLING MIND/MOTION SENSOR/E-PORT ON USI ALPINE FOOD MACHINE
INSTRUCTIONS FOR INSTALLING MIND/MOTION SENSOR/E-PORT ON USI ALPINE FOOD MACHINE Read these instructions carefully before installing the kit. If you are having problems installing the kit, please call
More informationModel EL8500 Series. Bagless Upright. Assembly/Disassembly Guide 1
Model EL8500 Series Bagless Upright Assembly/Disassembly Guide 1 Table Of Contents Parts Removal / Installation Guide Belt & Brushroll Section A Page 3 Hood Assembly Section B Page 3 Main PCB Board Section
More information* * Inside Toyota Avalon. Tools Required IMPORTANT
Revision 08/02/16 2013- Toyota Avalon IMPORTANT Before starting, compare items on your invoice with items received. Carefully check through packaging material. If any item is missing, please call Crutchfield
More informationService Manual Mozart Fireplace
Service Manual Mozart Fireplace Model Numbers: CFP3913 REV PCN DATE 00 11637 Sep 23, 09 Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N1R 7G8 1-888-346-7539 www.dimplex.com In
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationELECTRICAL SYSTEM UPGRADE
NEW CONTROLLER & ELECTRICAL SYSTEM UPGRADE FOR DAIRY TECH, INCORPORATED 10, 30 & 60G PASTEURIZERS Parts to Include 2 Wire ties (Nuts) 2 sticky wire mount pads Large Rubber Grommet (for bottom of electric
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FST KIT FOR PORT INJECTION 2013+ FORD FOCUS ECOBOOST Document: 19-0168 Support: info@radiumauto.com Working under the vehicle is required. This installation is best performed
More informationWritten By: Sam Lionheart
iphone 5s Front Panel Replacement Replace the cracked or broken screen on your iphone 5s. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 33 INTRODUCTION For an easier repair, use
More information(31 ) ZEON CONTROL PACK RELOCATION KIT
ORIGINAL INSTRUCTIONS SYMBOL INDEX (31 ) ZEON CONTROL PACK RELOCATION KIT SYMBOL EXPLANATION Read All Product Literature SYMBOL EXPLANATION Always Wear Leather Gloves INSTALLATION GUIDE Always Wear Hearing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Part # 751-FP2500 IMPORTANT INFORMATION This Jagg oil cooler must be installed following these instructions. Read the easy-to-follow instructions fully prior to starting the installation
More informationCETAC Z-Drive Nylon Cable
CETAC Z-Drive Nylon Cable Installation Guide Manual Part Number 610104 rev2, 2010-14 Teledyne Technologies Inc, Printed in USA Overview This guide describes how to replace the nylon line which operates
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL PUMP HANGER 08+ MITSUBISHI LANCER EVOLUTION X Support: info@radiumauto.com Document# 19-0116 WARNING: DO NOT EXPOSE WORK AREA TO ANY SPARKS OR FIRE. DO NOT SMOKE WHILE WORKING
More informationPart Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short Bracket PF3000 Pro
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short 2000105-2 1 PFadvantage Bracket PF3000 Pro 2000773 1 Cable Kit
More informationINSTALLATION INSTRUCTIONS Mitsubishi Lancer Evolution VIII / IX Fuel Surge Tank Kit Document#
d INSTALLATION INSTRUCTIONS Mitsubishi Lancer Evolution VIII / IX Fuel Surge Tank Kit Document# 19-0077 Brie Tech Support: info@radiumauto.com CAUTION: Exercise extreme caution when working with the fuel
More informationPART NUMBER: H630SSJ000. Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4)
Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4) E. Clip B. Harness (1) C. Cable tie (8) F. Mounting Hardware (2) G. Replacement Speaker (2) H. HVAC Duct extension (2) IMPORTANT:
More informationReplacing the Batteries in the Fortress LI 660
Replacing the Batteries in the Fortress LI 660 This FTS describes how to replace the batteries in Fortress LI 660 units. Batteries should be replaced by a qualified technician. If you have any questions
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support:
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: info@radiumauto.com These instructions are based on a vehicle with an OEM turbocharger
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Infiniti JX (2013) PART NUMBER: 999F3 YY000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationPARTS LIST. REPLACEMENT PARTS and ACCESSORIES PREPARATION VN1600. PREPARATION VN1500D and VN800B
INSTALLATION AND OWNER S MANUAL Light Bar N925 for Installation to: Kawasaki VN1500D&E and VN800B Pages 1,2,3 and 5 Kawasaki VN1600 Pages 1, 4 and 5 PARTS LIST QTY. PART NO. DESCRIPTION 1 N925 Light Bar
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL PUMP HANGER MITSUBISHI LANCER EVOLUTION X Support: info@radiumauto.com Document# 19-0116 WARNING: DO NOT EXPOSE WORK AREA TO ANY SPARKS OR FIRE. DO NOT SMOKE WHILE WORKING
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW REGULATOR (742-269) Ford Mustang 1996 2004 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationIMPORTANT SAFETY INFORMATION
Service Manual Model BLF50 UL Part Number 6906780100 IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to service this fireplace. For your safety, always comply with all warnings
More informationZZPerformance.com ZZP 3 Redline Cold Air Intake GEN 2
Tools you will need: Flat Blade Screwdriver Phillips Screwdriver 10mm End Wrench Ratchet Extension 5.5mm Socket 7mm Socket 10mm Socket 13mm Deep Socket ZZPerformance.com ZZP 3 Redline Cold Air Intake GEN
More informationAmTryke Adult Recumbent Model HP1000 #50-HC-1000
AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS IMPORTANT Before opening your Lights.com fixture, please make sure that you carefully read through these instruction sheets. Consider having your fixture installed by a qualified
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationSCION FR-S FOG LIGHTS
Part #: PT413-18130 Conflicts: Lowering Springs PTR07-18130-LL (California only) Kit Contents: For Anniversary Edition, Monogram & RS 2.0 vehicles, additional parts need to be ordered (PT413-18130-LL)
More informationYARIS 4-DOOR 2007 INTERIOR LIGHT UPGRADE
Document # 3999 4/26/06 4-DOOR 2007 INTERIOR LIGHT UPGRADE Preparation Part Number: 00016-52060 Code: IL1 Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide 3 1 Hardware
More informationINSTALLATION INSTRUCTIONS
2007-Current Jeep Wrangler 360º System for Factory MyGig Display (Kit # AVMS-3701) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit:
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationDrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationTABLE OF CONTENTS. Ram Assembly
TABLE OF CONTENTS DUC Cover------------------------------------------------------------------------------------ 00 Table of Contents----------------------------------------------------------------------------
More informationSALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT
= SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT INSTALLATION MANUAL: 2005-09 Mustang 4.6L 3V P/N: 10-8002-C12000B KIT P/N: 10-2903-B11511* Saleen Performance, Inc. 1225 East Maple Rd. Troy,
More informationToyota Prius Interior Light Upgrade
Toyota Prius 2012- Interior Light Upgrade Part Number 00016-00095 Accesory Code: IL2 Conflicts Kit Contents Item # Quantity Reqd. Description 1 1 Y Adapter 2 1 Wire harness 3 1 Hardware Kit 4 2 White Light
More informationAmp & Speaker Upgrade Install Instructions for Victory Cross Country
Amp & Speaker Upgrade Install Instructions for Victory Cross Country Tools Needed: 13mm Socket 4mm Ball Head Allen Socket 5mm Allen Wrench 10mm Wrench Wire Cutters Wire Strippers Phillips Screwdriver Pocket
More informationMK7 GTI Electronic Folding Mirror Conversion
MK7 GTI Electronic Folding Mirror Conversion 01 Mirror and Switch Installation 1. Using a soft pry tool remove the trim panel on the driver side door handle. 02 2. Remove 2 T-30 torx screws. 03 3. On the
More informationInstallation Instructions For Part Number: Scoop and Snorkel Kit
Installation Instructions For Part Number: 883-275 Scoop and Snorkel Kit 2008-14 Polaris Ranger RZR 800 800 E.F.I. Tools Required For Installation: 7/16 and 1/2 Wrenches. 10mm, 7/16, and 1/2 Sockets. T-25
More informationInstallation instructions, accessories. Body kit
Installation instructions, accessories Instruction No 31265373 Version 1.1 5 Part. No. Body kit IMG-256263 Volvo Car Corporation Body kit - 31265373 - V1.1 Page 1 / 42 Equipment A0000162 A0000163 IMG-239664
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi These instructions are based on a vehicle with an OEM turbocharger and top-mount intercooler. If a front-mount
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALL KIT Honda S2000 Document# 19-0063 Support: info@radiumauto.com WARNING: DO NOT SMOKE WHILE WORKING ON FUEL SYSTEMS. KEEP SPARKS AND OPEN FLAMES AWAY FROM
More informationRemove Air Cleaner Cover and. Filter
Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove
More informationINSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT
INSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT BMW E46 3-Series, Excl Convertible Document: 19-0056 Support: info@radiumauto.com Relieve fuel pressure in vehicle before beginingthe installation. Disconnect
More informationMaterials List: Tools List:
Materials List: Anchor assembly Automated power supply Automated power supply hardware packet Automation bracket assembly Automation bracket assembly hardware packet Automation winch assembly Cable Cable
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support:
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: info@radiumauto.com These instructions are based on a vehicle with an OEM turbocharger
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Rear Vision System Mirror Display 2013-Current Ram (Kit part number 1009-9518) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Rear
More informationUpgrade v3 to v3.2. SeeMeCNC Guides. Upgrade v3 to v3.2. Rostock Max v3 Uprgade to v3.2. Written By: SeeMeCNC seemecnc.dozuki.
SeeMeCNC Guides Upgrade v3 to v3.2 Rostock Max v3 Uprgade to v3.2 Written By: SeeMeCNC 2018 seemecnc.dozuki.com/ Page 1 of 34 INTRODUCTION This guide is intended to Upgrade a Rostock Max v3 to a Rostock
More informationInstructions for the Replacement of CWP ROMA s and Repair of Lower Support Frame.
Instructions for the Replacement of CWP ROMA s and Repair of Lower Support Frame. The following information describes the procedure to remove, and replace ROMA s. In addition, the procedure for replacing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL PUMP SLEEVE INSTALLATION KIT 2001-2006 BMW E46 M3 Document# 19-0058 Customer Support: info@radiumauto.com 1. There are 2 common ways to relieve fuel pressure on the BMW.
More informationA B C D E F. Tools Required (supplied by others)
Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT 2013+ FORD FOCUS ECOBOOST Document: 19-0168 Support: info@radiumauto.com Working under the vehicle is required. This installation is best performed with the
More informationYamaha Nytro Relocator Kit
Included Parts: 1 Relocator bracket assembly 2 Upper assembly Oilite bushing halves 1 Lower steering block assembly 2 Lower assembly Oilite bushing halves 1 Tube of Loc-tite OFTRacing.com Email Scott Moto
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationInstallation Instructions for 2018 Jeep Grand Cherokee Laredo & Altitude and 2018 Dodge Durango SXT & SXT Plus
Thank you for purchasing the SmartStopStart module! Please read this important information and keep this document with your vehicle owner's manual. Installation Instructions for 2018 Jeep Grand Cherokee
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More informationShaver Industries. Assembly Instructions Vertical Vinyl Curtain Door DT2 Wire Rope Replacement
Shaver Industries 20 Steckle Place, Kitchener, ON N2E 2C3 Ph 1(888) 766 8328 www.shaverinc.com Assembly Instructions Vertical Vinyl Curtain Door DT2 Wire Rope Replacement Overview: Preparation: Installation:
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Chevy Blazer 1992-1994, Chevy Suburban 1992-1999, Chevy Tahoe 1995-1999, Chevy Tahoe Limited 2000, GMC Suburban 1992-1999, GMC Yukon 1992-1999, GMC Yukon Denali
More informationCAUTION. INSTALLATION INSTRUCTIONS Part Number Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck
INSTALLATION INSTRUCTIONS Part Number 69110 Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2009 ACCORD 4-DOOR Publications No. AII 40008 Issue Date JULY 2008 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Electronic Tailgate Lock Kit Nissan Titan 999M2-W3005 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Electronic
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Coupe and Sedan (2011+) PART NUMBER: 999F4 AX008 - Universal Security Lighting Kit. KIT CONTENTS:
More information401B/1KDB CoolRite/FreezeRite Installation Manual I003
401B/1KDB CoolRite/FreezeRite Installation Manual 99-16105-I003 Copyright 2011 by ALL rights reserved. Information in this document is subject to change without notice. Companies, names and data used in
More informationInstallation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6
Page 1 Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake
More informationGOMINIGO Third Brake Light Pulsar Kit. Installation Instructions
Page 1 of 8 Mini Cooper Installation Instructions This kit allows the owner of any MINI Cooper or Cooper S to create a blinking effect from the third brake light assembly. The MINI Cooper being hit from
More information920 Remote Control Switches
920 Remote Control Switches REMOTE CONTROL SWITCHES Service Bulletin This service bulletin for ASCO 920 Remote Control Switches explains how to replace the main s, operator coil, control s, and how to
More informationScion xa SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS31-00051 Kit Contents Item # Quantity Reqd. Description 1 1 Antenna, Interior 2 1 Antenna Tape Pad 3 1 Wire Harness 4 1 Bracket, Floor 5 3 Hardware Bags 6 3 Templates 7 1 SIRIUS
More information