Document Revision: 12.C Auto Selector Template Revision: 49

Transcription

1 PrtNde FPC-N34 and PrtNde FPC-N35 Startup Guide Fr Interfacing Lchinvar Prducts: SYNC, Knight /Knight XL /Armr/Wall Munt/Wall Hung, Crest, Cpper-Fin II, Pwer Fin, Knight FTXL T Building Autmatin Systems: BACnet MS/TP, BACnet/IP, Mdbus TCP/IP, Metasys N2 and LnWrks APPLICABILITY & EFFECTIVITY Explains PrtNde FPC-N34 and FPC-N35 hardware and hw t install it. The instructins are effective fr the abve as f September 2015 Dcument Revisin: 12.C Aut Selectr Template Revisin: 49

2 Technical Supprt: INS70085/ / Rev H Lchinvar s PrtNde Startup Guide Thank yu fr purchasing the PrtNde fr Lchinvar Bilers. Please call Lchinvar fr Technical supprt f the PrtNde prduct. FieldServer des nt prvide direct supprt. If Lchinvar needs t escalate the cncern, they will cntact FieldServer fr assistance. Supprt Cntact Infrmatin: Lchinvar, LLC 300 Maddx Simpsn Pkwy. Lebann, TN Lchinvar Service: tech@lchinvar.cm Website: Page 2 f 49

3 A Quick Start Guide 1. Recrd the infrmatin abut the unit. (Sectin 2.1) 2. Set the device s Mdbus RTU serial settings (i.e. baud rate, parity, stp bits) and Mdbus Nde-ID fr each f the devices that will be cnnected t PrtNde FPC-N34 r FPC-N35. (Sectin 2.2) 3. Select a stred cnfiguratin and set field prtcl MAC address/nde-id/device Instance, and baud rate. (Sectin 2.3) 4. Cnnect PrtNde s 6 pin RS-485 cnnectr t the Mdbus RS-485 netwrk that is cnnected t each f the devices. (Sectin 3.2) 5. Cnnect PrtNde FPC-N34 s 3 pin RS-485 prt t the Field Prtcl cabling, (Sectin 3.3) r cnnect PrtNde FPC-N35 s 2 pin LnWrks prt t the Field Prtcl cabling. (Sectin 3.4) 6. Cnnect Pwer t PrtNde s 6 pin cnnectr. (Sectin 3.5) 7. BACnet/IP r Mdbus TCP/IP (FPC-N34): Use the PrtNde s embedded tl which is accessed with a brwser, referred t in this manual as the Web Cnfiguratr, t change the IP address. N changes t the cnfiguratin file are necessary. (Sectin 4) 8. LnWrks (FPC-N35): The PrtNde must be cmmissined n the LnWrks Netwrk. This needs t be dne by the LnWrks administratr using a LnWrks Cmmissining tl. (Sectin 6) Page 3 f 49

4 Certificatins BTL MARK BACNET TESTING LABORATORY The BTL Mark n PrtNde RER is a symbl that indicates that a prduct has passed a series f rigrus tests cnducted by an independent labratry which verifies that the prduct crrectly implements the BACnet features claimed in the listing. The mark is a symbl f a high-quality BACnet prduct. G t fr mre infrmatin abut the BACnet Testing Labratry. Click here fr BACnet PIC Statement. LONMARK CERTIFICATION LnMark Internatinal is the recgnized authrity fr certificatin, educatin, and prmtin f interperability standards fr the benefit f manufacturers, integratrs and end users. LnMark Internatinal has develped extensive prduct certificatin standards and tests t prvide the integratr and user with cnfidence that prducts frm multiple manufacturers utilizing LnMark devices wrk tgether. FieldServer Technlgies has mre LnMark Certified gateways than any ther gateway manufacturer, including the PrtCessr, PrtCarrier and PrtNde fr OEM applicatins and the full featured, cnfigurable gateways. Page 4 f 49

5 TABLE OF CONTENTS 1 Intrductin PrtNde Gateway BACnet/LnWrks Setup fr PrtCessr PrtNde FPC-N34/FPC-N Recrd Identificatin Data Cnfiguring Device Cmmunicatins Set Mdbus COM setting n all f the devices cnnected t the PrtNde Set Mdbus RTU Nde-ID fr each f the devices attached t the PrtNde BMS Netwrk Settings: Selecting Stred Cnfiguratins, Setting the Mac Address, Device Instance, and Baud Rate Selecting Cnfiguratin Files fr Devices: S bank DIP Switches S0 S BACnet MS/TP and BACnet/IP DIP Switch Settings LnWrks DIP Switch Settings BACnet MS/TP (FPC-N34): Setting the MAC Address fr BMS Netwrk BACnet MS/TP and BACnet/IP (FPC-N34): Setting the Device Instance BACnet MS/TP r BACnet/IP: Assigning Specific Device Instances Metasys N2 r Mdbus TCP/IP (FPC-N34): Setting the Nde-ID BACnet MS/TP (FPC-N34): Setting the Serial Baud Rate fr BMS Netwrk Baud Rate DIP Switch Selectin Interfacing PrtNde t Devices PrtNde FPC-N34 and FPC-N35 Shwing Cnnectin Prts Device Cnnectins t PrtNde End f Line Terminatin Switch fr the Mdbus RS-485 Device Netwrk Lchinvar s Armr, SYNC/Armr X2, Knight/Knight XL, Crest, Cpper-Fin II and FTXL Lw Vltage Mdbus RTU Cnnectin Wiring t the PrtNde: BACnet MS/TP r Metasys N2 (FPC-N34): Wiring Field Prt t RS-485 BMS Netwrk LnWrks (FPC-N35): Wiring Field Prt t LnWrks Netwrk Pwer-Up PrtNde BACnet/IP and Mdbus TCP/IP: Change the Prtnde IP Address Cnnect the PC t PrtNde via the Ethernet Prt BACnet/IP and Mdbus TCP/IP: Setting IP Address fr Field Netwrk BACnet MS/TP and BACnet/IP: Setting Nde_Offset t Assign Specific Device Instances LnWrks (FPC-N35): Cmmissining PrtNde n a lnwrks Netwrk Cmmissining PrtNde FPC-N35 n a LnWrks Netwrk Instructins t Dwnlad XIF File frm PrtNde FPC-N35 Using Brwser CAS BACnet Explrer fr Validating PrtNde in the Field Dwnlading the CAS Explrer and Requesting an Activatin Key CAS BACnet Setup CAS BACnet MS/TP Setup CAS BACnet BACnet/IP Setup Appendix A. Trubleshting Appendix A.1. Viewing Diagnstic infrmatin Appendix A.2. Check Wiring and Settings Appendix A.3. Take Diagnstic Capture With the FieldServer Utilities Appendix A.4. BACnet: Setting Netwrk_Number fr mre than ne PrtNde n Subnet Appendix A.5. LED Diagnstics fr Mdbus RTU Cmmunicatins Between PrtNde and Devices. 33 Appendix A.6. Passwrds Appendix B. Additinal Features Page 5 f 49

6 Appendix B.1. DIP switch settings t supprt Metasys N Appendix C. Vendr Infrmatin - Lchinvar Appendix C.1. Sync Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Appendix C.2. Knight Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Appendix C.3. Crest Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Appendix C.4. Cpper-Fin II Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Appendix C.5. Pwer Fin Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Appendix C.6. Knight FTXL Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Appendix D. A Bank DIP Switch Settings Appendix D.1. A Bank DIP Switch Settings Appendix E. Reference Appendix E.1. Specificatins Appendix E.1.1. Cmpliance with UL Regulatins Appendix F. Limited 2 Year Warranty LIST OF FIGURES INS70085/ / Rev H Lchinvar s PrtNde Startup Guide Figure 1: PrtCessr Part Numbers... 8 Figure 2: Mdbus RTU COM Settings... 8 Figure 3: Lchinvar s Mdbus COM bard shwing serial DIP Switches... 8 Figure 4: S Bank DIP Switches Figure 5: MAC Address DIP Switches Figure 6: Baud Rate DIP Switches Figure 7: BMS Baud Rate Figure 8: PrtNde BACnet FPC-N34 (upper) and PrtNde FPC-N35 (lwer) Figure 9: Pwer and RS-485 Cnnectins Figure 10: Mdbus RS-485 End-Of-Line Terminatin Switch n the PrtNde N34 (left) and Figure 11: Lw Vltage Mdbus RTU Cnnectin Wiring t the PrtNde Figure 12: Cnnectin frm PrtNde t RS-485 Field Netwrk Figure 13: RS-485 BMS Netwrk EOL Switch Figure 14: LnWrks Terminal Figure 15: Required current draw fr the PrtNde Figure 16: Pwer Cnnectins Figure 17: Web Cnfiguratin Screen Figure 18: Changing IP Address via FST Web GUI Figure 19: Web Cnfiguratr screen Figure 20: LnWrks Service Pin Lcatin Figure 21: Sample f Fserver.XIF File Being Generated Figure 22: Dwnlading the CAS Explrer Figure 23: Requesting CAS Activatin Key Figure 24: Errr messages screen Figure 25: Ethernet Prt Lcatin Figure 26: Web Cnfiguratr shwing setting the netwrk number fr BACnet/IP Figure 27: Diagnstic LEDs Figure 28: Specificatins Page 6 f 49

7 1 INTRODUCTION 1.1 PrtNde Gateway PrtNde is an external, high perfrmance Building Autmatin multi-prtcl gateway that has been preprgrammed fr Lchinvar s prducts (hereafter called device ) t varius building autmatin prtcls. These prtcls include BACnet 1 MS/TP, BACnet/IP, Metasys 2 N2 by JCI, Mdbus TCP/IP, and LnWrks 3. Cnfiguratins fr the varius prtcls are stred within the PrtNde and are selectable via DIP switches fr fast and easy installatin. It is nt necessary t dwnlad any cnfiguratin files t supprt the required applicatins. The PrtNde is pre-laded with tested Prfiles/Cnfiguratins fr the supprted devices. 1 BACnet is a registered trademark f ASHRAE 2 Metasys is a registered trademark f Jhnsn Cntrls Inc. 4 LnWrks is a registered trademark f Echeln Crpratin Page 7 f 49

8 2 BACNET/LONWORKS SETUP FOR PROTOCESSOR PROTONODE FPC- N34/FPC-N Recrd Identificatin Data Each PrtNde has a unique part number lcated n the side r the back f the unit. This number shuld be recrded, as it may be required fr technical supprt. The numbers are as fllws: Mdel Part Number PrtNde FPC-N34 FPC-N PrtNde FPC-N35 FPC-N Figure 1: PrtCessr Part Numbers FPC-N34 units have the fllwing 3 prts: RS Ethernet + RS-485. FPC-N35 units have the fllwing 3 prts: LnWrks + Ethernet + RS Cnfiguring Device Cmmunicatins Set Mdbus COM setting n all f the devices cnnected t the PrtNde All f the Serial devices cnnected t PrtNde MUST have the same Baud Rate, Data Bits, Stp Bits, and Parity settings. Figure 2 specifies the device serial prt settings required t cmmunicate with the PrtNde. Serial Prt Setting Device Prtcl Mdbus RTU Baud Rate 9600 Parity Nne Data Bits 8 Stp Bits 2 Figure 2: Mdbus RTU COM Settings Figure 3: Lchinvar s Mdbus COM bard shwing serial DIP Switches Page 8 f 49

9 2.2.2 Set Mdbus RTU Nde-ID fr each f the devices attached t the PrtNde Set the Mdbus Nde-ID fr each f the devices attached t PrtNde. The Mdbus Nde-ID s need t be uniquely assigned, starting with a value f 1 fr the first device. Mdbus Nde-ID values fr additinal devices must be sequential (2, 3, 4, ). Page 9 f 49

10 2.3 BMS Netwrk Settings: Selecting Stred Cnfiguratins, Setting the Mac Address, Device Instance, and Baud Rate Selecting Cnfiguratin Files fr Devices: S bank DIP Switches S0 S3 The S bank f DIP switches (S0 - S3) are used t select and lad a cnfiguratin file frm a grup f pretested/preladed cnfiguratin files which are stred in the PrtNde FPC-N34 (BACnet MS/TP, BACnet/IP, Mdbus TCP/IP, Metasys N2) and the PrtNde FPC-N35 (LnWrks). S0 S1 S2 S3 S0 S3 DIP Switches Figure 4: S Bank DIP Switches S Bank DIP Switch Lcatin BACnet MS/TP and BACnet/IP DIP Switch Settings The fllwing chart describes S0 - S3 DIP Switch cnfiguratin settings fr 1 thrugh 8 device applicatins t supprt BACnet MS/TP and BACnet/IP n a PrtNde FPC-N34. PrtCarrier DIP Switches Prfile - FPC-N S0 S1 S2 S3 BACnet/IP / BACnet MS/TP / Mdbus TCP/IP SYNC Deg_C Off Off Off Off BACnet/IP / BACnet MS/TP / Mdbus TCP/IP Knight/Knight XL/Armr/Wall Munt/Wall Hung Deg_C On Off Off Off BACnet/IP / BACnet MS/TP / Mdbus TCP/IP Crest Deg_C Off On Off Off BACnet/IP / BACnet MS/TP / Mdbus TCP/IP Cpper-Fin II Deg_C On On Off Off BACnet/IP / BACnet MS/TP / Mdbus TCP/IP Pwer Fin Deg_C Off Off On Off BACnet/IP / BACnet MS/TP / Mdbus TCP/IP Knight FTXL Deg_C On Off On Off BACnet/IP / BACnet MS/TP / Mdbus TCP/IP SYNC Deg_F Off On On Off BACnet/IP / BACnet MS/TP / Mdbus TCP/IP Knight/Knight XL/Armr/Wall Munt/Wall Hung Deg_F On On On Off BACnet/IP / BACnet MS/TP / Mdbus TCP/IP Crest Deg_F Off Off Off On BACnet/IP / BACnet MS/TP / Mdbus TCP/IP Cpper-Fin II Deg_F On Off Off On BACnet/IP / BACnet MS/TP / Mdbus TCP/IP Pwer Fin Deg_F Off On Off On BACnet/IP / BACnet MS/TP / Mdbus TCP/IP Knight FTXL Deg_F On On Off On See Appendix B.1 fr the Cnfiguratin DIP switch settings t supprt Metasys N2 n a PrtNde FPC- N34. NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF. Page 10 f 49

11 LnWrks DIP Switch Settings The fllwing chart describes the DIP switch settings t supprt LnWrks n a PrtNde FPC-N35. PrtCarrier DIP Switches Prfile - FPC-N S0 S1 S2 S3 LnWrks SYNC Off Off Off Off LnWrks Knight/Knight XL/Armr/Wall Munt/Wall Hung On Off Off Off LnWrks Crest Off On Off Off LnWrks Cpper-Fin II On On Off Off LnWrks Pwer Fin Off Off On Off LnWrks Knight FTXL On Off On Off NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF BACnet MS/TP (FPC-N34): Setting the MAC Address fr BMS Netwrk Only 1 MAC address is set fr PrtNde regardless f hw many devices are cnnected t PrtNde. Set the BACnet MS/TP MAC addresses f the PrtNde t a value between 1 t 127 (MAC Master Addresses); this is s that the BMS Frnt End can find the PrtNde via BACnet aut discvery. Nte: Never set a BACnet MS/TP MAC Address frm 128 t 255. Addresses frm 128 t 255 are Slave Addresses and can nt be discvered by BMS Frnt Ends that supprt aut discvery f BACnet MS/TP devices. Set DIP switches A0 A7 t assign MAC Address fr BACnet MS/TP fr the PrtNde FPC-N34. Please refer t Appendix D.1 fr the cmplete range f MAC Addresses and DIP switch settings. Figure 5: MAC Address DIP Switches NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF. Page 11 f 49

12 2.3.3 BACnet MS/TP and BACnet/IP (FPC-N34): Setting the Device Instance The A Bank f DIP switches are used fr tw purpses: Fr BACnet MS/TP, they are used t set the BACnet MS/TP MAC address. (Sectin 2.3.2) Fr bth BACnet MS/TP and BACnet/IP, they are als used t determine the BACnet Device Instance values. The BACnet Device Instance can range frm 1 t 4,194,303. The BACnet device instances will be calculated by taking the Nde_Offset (default is 50,000) fund in Web Cnfiguratr (Sectin ) and adding it t the value f the A Bank DIP switches. When mre than ne device is cnnected t the PrtNde, the subsequent BACnet Device Instance values will be sequential frm the first/previus device. Fr example: Given that: Device Instance = Nde_Offset + A Bank DIP switch value Default Nde_Offset value = 50,000 A Bank DIP switch value = 11 Then the Device Instance values fr the devices are: Device 1 Instance = 50,011 Device 2 Instance will then be 50,011(Device Instance 1) +1 = 50,012 Device 3 Instance will then be 50,012 (previus Device Instance) +1 = 50, BACnet MS/TP r BACnet/IP: Assigning Specific Device Instances With the default Nde_Offset value f 50,000 the Device Instances values generated will be within the range f 50,001 t 50,127. The values allwed fr a BACnet Device Instance can range frm 1 t 4,194,303. T assign a specific Device Instance (r range), change the Nde_Offset value. Methds fr changing the Nde_Offset value are prvided in Sectin 4.2 This step cannt be perfrmed until after the unit is cnnected and pwered Metasys N2 r Mdbus TCP/IP (FPC-N34): Setting the Nde-ID Set DIP switches A0 A7 t assign a Nde-ID fr Metasys N2 r Mdbus TCP/IP t the PrtNde FPC-N34. Metasys N2 and Mdbus TCP/IP Nde-ID Addressing: Metasys N2 and Mdbus TCP/IP Nde- ID s range frm Please refer t Appendix D.1 fr the full range f addresses fr setting Nde-ID. Page 12 f 49

13 2.3.5 BACnet MS/TP (FPC-N34): Setting the Serial Baud Rate fr BMS Netwrk DIP Switches B0 B3 can be used t set the serial baud rate t match the baud rate required by the Building Management System fr BACnet MS/TP. DIP Switches B0 B3 are disabled n PrtNde FPC-N35 (FPC-N35 LnWrks). The baud rate n PrtNde fr Metasys N2 is set fr DIP Switches B0 B3 are disabled fr Metasys N2 n PrtNde FPC-N34. B0 B1 B2 B3 Figure 6: Baud Rate DIP Switches NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF Baud Rate DIP Switch Selectin Baud B0 B1 B2 B On On On Off Off Off Off On 38400* On On Off On Off Off On On On Off On On Figure 7: BMS Baud Rate * Factry default setting = 38,400 Page 13 f 49

14 3 INTERFACING PROTONODE TO DEVICES 3.1 PrtNde FPC-N34 and FPC-N35 Shwing Cnnectin Prts Figure 8: PrtNde BACnet FPC-N34 (upper) and PrtNde FPC-N35 (lwer) Page 14 f 49

15 3.2 Device Cnnectins t PrtNde PrtNde 6 Pin Phenix cnnectr fr RS-485 Devices The 6 pin Phenix cnnectr is the same fr PrtNde FPC-N34 (BACnet) and FPC-N35 (LnWrks). Pins 1 thrugh 3 are fr Mdbus RS-485 devices. The RS-485 GND (Pin 3) is nt typically cnnected. Pins 4 thrugh 6 are fr pwer. D nt cnnect pwer (wait until Sectin 4). Device Pins PrtNde Pin # Pin assignment Pin RS Pin 1 RS Pin RS Pin 2 RS Pin GND Pin 3 RS-485 GND Pwer In (+) Pin 4 V + Pwer In (-) Pin 5 V - Frame Grund Pin 6 FRAME GND Figure 9: Pwer and RS-485 Cnnectins Page 15 f 49

16 3.2.1 End f Line Terminatin Switch fr the Mdbus RS-485 Device Netwrk On lng RS-485 cabling runs, the RS-485 trunk must be prperly terminated at each end. The PrtNde has an End Of Line (EOL) blue jumper. The default setting fr this Blue EOL switch is OFF with the jumper straddling the pins clsest t the inside f the bard f the PrtNde. On shrt cabling runs the EOL switch des nt t need t be turned ON. If the PrtNde is placed at ne f the ends f the trunk, set the blue EOL jumper t the ON psitin straddling the pins clsest t the utside f the bard f the PrtNde. Always leave the single Red Jumper in the A psitin (default factry setting). Mdbus RS-485 EOL Switch Leave in A Psitin Figure 10: Mdbus RS-485 End-Of-Line Terminatin Switch n the PrtNde N34 (left) and PrtNde N35 (right) Page 16 f 49

17 3.2.2 Lchinvar s Armr, SYNC/Armr X2, Knight/Knight XL, Crest, Cpper -Fin II and FTXL Lw Vltage Mdbus RTU Cnnectin Wiring t the PrtNde: On the Lchinvar s Mdbus terminal strip, cnnect Pin A (RS-485+) t B+ (RS-485+) n the PrtNde s 6 Pin Phenix cnnectr. On the Lchinvar s Mdbus terminal strip, cnnect Pin B (RS-485-) t A- (RS-485-) n the PrtNde s 6 pin Phenix cnnectr. The Shield Pin the terminal strip which is Grund n the des nt need t be grunded t the PrtNde. Figure 11: Lw Vltage Mdbus RTU Cnnectin Wiring t the PrtNde Page 17 f 49

18 3.3 BACnet MS/TP r Metasys N2 (FPC-N34): Wiring Field Prt t RS-485 BMS Netwrk Cnnect the BACnet MS/TP r Metasys N2 RS-485 netwrk wires t the 3-pin RS-485 cnnectr n PrtNde FPC-N34 as shwn belw in Figure 12. The RS-485 GND (Pin 3) is nt typically cnnected. See Sectin 4 fr infrmatin n cnnecting t BACnet/IP netwrk. If the PrtNde is the last device n the BACnet MS/TP r Metasys N2 trunk, then the End-Of-Line Terminatin Switch needs t be enabled (Figure 13). The default setting frm the factry is OFF (switch psitin = right side). T enable the EOL Terminatin, turn the EOL switch ON (switch psitin = left side). BMS RS- 485 Wiring PrtNde Pin # Pin Assignment RS Pin 1 RS RS Pin 2 RS Pin 3 RS-485 GND + - G Figure 12: Cnnectin frm PrtNde t RS-485 Field Netwrk End-f-Line Switch Figure 13: RS-485 BMS Netwrk EOL Switch 3.4 LnWrks (FPC-N35): Wiring Field Prt t LnWrks Netwrk Cnnect PrtNde t the field netwrk with the LnWrks terminal using a twisted pair nnshielded cable. LnWrks has n plarity. Figure 14: LnWrks Terminal Page 18 f 49

19 3.5 Pwer-Up PrtNde Apply pwer t PrtNde as shw belw in Figure 16. Ensure that the pwer supply used cmplies with the specificatins prvided in Appendix E.1. PrtNde accepts either 9-30VDC r VAC n pins 4 and 5. Frame GND shuld be cnnected. Pwer Requirement fr PrtNde External Gateway Current Draw Type PrtNde Family 12VDC/VAC 24VDC/VAC 30VDC FPC N34 (Typical) 170mA 100mA 80mA FPC N34 (Maximum) 240mA 140mA 100mA FPC N35 (Typical) 210mA 130mA 90mA FPC N35 (Maximum) 250mA 170mA 110mA Nte: These values are nminal and a safety margin shuld be added t the pwer supply f the hst system. A safety margin f 25% is recmmended. Figure 15: Required current draw fr the PrtNde Pwer t PrtNde PrtNde Pin # Pin Assignment Pwer In (+) Pin 4 V + Pwer In (-) Pin 5 V - Frame Grund Pin 6 FRAME GND Figure 16: Pwer Cnnectins Page 19 f 49

20 4 BACNET/IP AND MODBUS TCP/IP: CHANGE THE PROTONODE IP ADDRESS 4.1 Cnnect the PC t PrtNde via the Ethernet Prt Cnnect a Cat 5 Ethernet cable (Straight thrugh r Crss-Over) between the PC and PrtNde. The Default IP Address f PrtNde is , Subnet Mask is If the PC and PrtNde are n different IP Netwrks, assign a static IP Address t the PC n the xxx netwrk. G t > > Right-click n Lcal Area Cnnectin > Prperties Highlight > Select: Use the fllwing IP address Click twice Page 20 f 49

21 4.2 BACnet/IP and Mdbus TCP/IP: Setting IP Address fr Field Netwrk After setting yur PC t be n the same subnet as the PrtNde (Sectin 3.5), pen a web brwser n yur PC and enter the IP address f the PrtNde; the default address is The Web Cnfiguratr will be displayed as the landing page (Figure 19) Frm the Web Cnfiguratr landing page, click n the Diagnstics & Debugging buttn in the bttm right side f the page t access the FST Web GUI. Figure 17: Web Cnfiguratin Screen Page 21 f 49

22 Frm the FST Web GUI s landing page, click n Setup t expand the navigatin tree and then select Netwrk Settings t access the IP Settings menu. (Figure 18) Figure 18: Changing IP Address via FST Web GUI Enter the new IP address fr the PrtNde s Ethernet prt in the N1 IP address field. If necessary, change the Subnet Mask setting in the N1 Netmask field. If necessary, change the IP Gateway setting in the Default Gateway field. Nte: If the PrtNde is cnnected t a ruter, the IP Gateway f the PrtNde shuld be set t the IP address f the ruter that it is cnnected t. Click the System Restart buttn at the bttm f the page t apply changes and restart the PrtNde. Unplug Ethernet cable frm PC and cnnect the PrtNde t the netwrk hub r ruter. Recrd the IP address assigned t the PrtNde fr future reference. Page 22 f 49

23 5 BACNET MS/TP AND BACNET/IP: SETTING NODE_OFFSET TO ASSIGN SPECIFIC DEVICE INSTANCES After setting yur PC t be n the same subnet as the PrtNde (Sectin 4.1), pen a web brwser n yur PC and enter the IP address f the PrtNde; the default address is The Web Cnfiguratr will be displayed as yur landing page. (Figure 19) Nde_Offset field will be presented displaying the current value (default = 50,000). Change the value f Nde_Offset t establish the desired Device Instance values, and click SUBMIT. Given that: Device Instance = Nde_Offset + A Bank Setting Then: Nde_Offset (required) = Device Instance (desired) A Bank Setting Fr example: Device 1 has a Mdbus Nde-ID f 1 Device 2 has a Mdbus Nde-ID f 2 Device 3 has a Mdbus Nde-ID f 3 A Bank DIP switches setting = 11 Desired Device Instance fr 1 st device = 1,011 Nde_Offset (required) = 1,011 (A Bank Setting) = 1, = 1,000 The Nde_Offset value will be applied t all devices. Device 1 Instance will then be = 1,000 + A Bank Setting = 1, = 1,011 Device 2 Instance will then be = Previus Value + 1 = 1, = 1,012 Device 3 Instance will then be = Previus Value + 1 = 1, = 1,013 Figure 19: Web Cnfiguratr screen Page 23 f 49

24 6 LONWORKS (FPC-N35): COMMISSIONING PROTONODE ON A LONWORKS NETWORK Cmmissining may nly be perfrmed by the LnWrks administratr. 6.1 Cmmissining PrtNde FPC-N35 n a LnWrks Netwrk The User will be prmpted by the LnWrks Administratr t hit the Service Pin n the PrtNde FPC-N35 at the crrect step f the Cmmissining prcess which is different fr each LnWrks Netwrk Management Tl. If an XIF file is required, see steps in Sectin t generate XIF Figure 20: LnWrks Service Pin Lcatin Instructins t Dwnlad XIF File frm PrtNde FPC-N35 Using Brwser Cnnect a Cat 5 Ethernet cable (Straight thrugh r Crss-Over) between the PC and PrtNde. The Default IP Address f PrtNde is , Subnet Mask is If the PC and PrtNde are n different IP Netwrks, assign a static IP Address t the PC n the xxx netwrk. Fr Windws XP: G t > > Right-click n Lcal Area Cnnectin > Prperties Highlight > Fr Windws 7: G t > > > > Right-click n Lcal Area Cnnectin > Prperties Highlight > Page 24 f 49

25 Fr Windws XP and Windws 7, select: Use the fllwing IP address Click twice Open a web brwser and g t the fllwing address: IP address f PrtCessr/fserver.xif Example: /fserver.xif If the web brwser prmpts yu t save file, save the file nt the PC. If the web brwser displays the xif file as a web page, save the file n yur PC as fserver.xif Figure 21: Sample f Fserver.XIF File Being Generated Page 25 f 49

26 7 CAS BACNET EXPLORER FOR VALIDATING PROTONODE IN THE FIELD PrtCessr has arranged a cmplementary 2 week fully functinal cpy f CAS BACnet Explrer (thrugh Chipkin Autmatin) that can be used t validate BACnet MS/TP and/r BACnet/IP cmmunicatins f PrtNde in the field withut having t have the BMS Integratr n site. A Serial r USB t RS-485 cnverter is needed t test BACnet MS/TP. 7.1 Dwnlading the CAS Explrer and Requesting an Activatin Key T request the cmplementary BACnet CAS key, g t and fill in all the infrmatin. Enter Vendr Cde lchinvar12. Once cmpleted, the address that was submitted will be registered. Figure 22: Dwnlading the CAS Explrer G t the fllwing web site, dwnlad and install the CAS BACnet Explrer t yur PC: Open CAS BACnet Explrer; in the CAS Activatin frm, enter the address that was registered and click n Request a key. The CAS key will then be ed t the registered address. Cut/paste key frm int the Prduct key field and click Activate. Figure 23: Requesting CAS Activatin Key Page 26 f 49

27 7.2 CAS BACnet Setup These are the instructins t set CAS Explrer up fr the first time n BACnet MS/ST and BACnet/IP CAS BACnet MS/TP Setup Using the Serial r USB t RS-485 cnverter, cnnect it t yur PC and the 3 Pin BACnet MS/TP cnnectr n PrtNde FPC-N34. In CAS Explrer, d the fllwing: Click n settings Check the BACnet MS/TP bx and uncheck the BACnet/IP and BACnet Ethernet bxes Set the BACnet MS/TP MAC address t 0 Set the BACnet MS/TP Baud Rate t Click Ok On the bttm right-hand crner, make sure that the BACnet MS/TP bx is green Click n discver Check all 4 bxes Click Send CAS BACnet BACnet/IP Setup See Sectin 4.1 t set the IP address and subnet f the PC that will be running the CAS Explrer. Cnnect a straight thrugh r crss Ethernet cable frm the PC t PrtNde. In CAS Explrer, d the fllwing: Click n settings Check the BACnet/IP bx and uncheck the BACnet MS/TP and BACnet Ethernet bxes In the Select a Netwrk Device bx, select the netwrk card f the PC by clicking n it Click Ok On the bttm right-hand crner, make sure that the BACnet/IP bx is green Click n discver Check all 4 bxes Click Send Page 27 f 49

28 Appendix A. Trubleshting Appendix A.1. Viewing Diagnstic infrmatin Type the IP address f the PrtNde int yur web brwser r use the FieldServer Tlbx t cnnect t the PrtNde. Click n Diagnstics and Debugging Buttn, then click n view, and then n cnnectins. If there are any errrs shwing n the Cnnectin page, please refer t Appendix A.2 fr the relevant wiring and settings. Figure 24: Errr messages screen Page 28 f 49

29 Appendix A.2. Check Wiring and Settings N COMS n Mdbus RTU side. If Tx/Rx are nt flashing rapidly then there is a COM issue n the Mdbus side and yu need t check the fllwing things: Visual bservatins f LEDs n PrtNde. (Appendix A.5) Check baud rate, parity, data bits, stp bits Check Mdbus device address Verify wiring Verify all the Mdbus RTU devices that were discvered in FST Web Cnfiguratr. (Sectin 5) Field COM prblems: Visual bservatins f LEDs n PrtNde. (Appendix A.5) Visual dipswitch settings (using crrect baud rate and device instance) Verify IP address setting Verify wiring If the prblem still exists, a Diagnstic Capture needs t be taken and sent t Sierra Mnitr Crpratin. (Appendix A.3) Appendix A.3. Take Diagnstic Capture With the FieldServer Utilities Once the Diagnstic Capture is cmplete, it t supprt@sierramnitr.cm. The Diagnstic Capture will allw us t rapidly diagnse the prblem. Ensure that FieldServer Tlbx is Laded n the PC that is currently being used, r dwnlad FieldServer-Tlbx.zip n the Sierra Mnitr Crpratin webpage, under Custmer Care: Resurce Center, Sftware Dwnlads: Extract the executable file and cmplete the installatin. Ethernet Prt Figure 25: Ethernet Prt Lcatin Disable any wireless Ethernet adapters n the PC/Laptp Disable firewall and virus prtectin sftware if pssible Cnnect a standard cat5 Ethernet cable between the PC and PrtNde Duble click n the FS Tlbx Utility Page 29 f 49

30 Step 1: Take a Lg Click n the diagnse icn f the desired device. Select full Diagnstic If desired, the default capture perid can be changed. Click n Start Diagnstic Page 30 f 49

31 Wait fr Capture perid t finish. Diagnstic Test Cmplete windw will appear. Step 2: Send Lg Once the Diagnstic test is cmplete, a.zip file will be saved n the PC. Chse pen t launch explrer and have it pint directly at the crrect flder. Send the Diagnstic zip file t supprt@sierramnitr.cm Page 31 f 49

32 Appendix A.4. BACnet: Setting Netwrk_Number fr mre than ne PrtNde n Subnet Fr bth BACnet MS/TP and BACnet/IP, if mre than ne PrtNde is cnnected t the same subnet, they must be assigned unique Netwrk_Number values. On the main Web Cnfiguratin screen, update the Netwrk Number with the netwrk_nr field and click submit. The default value is 50. Figure 26: Web Cnfiguratr shwing setting the netwrk number fr BACnet/IP Page 32 f 49

33 Appendix A.5. LED Diagnstics fr Mdbus RTU Cmmunicatins Between PrtNde and Devices Please see the diagram belw fr PrtNde FPC-N34 and FPC-N35 LED Lcatins. Diagnstic LEDs Tag SPL RUN ERR RX TX PWR Descriptin The SPL LED will light if the PrtNde is ff line. The RUN LED will start flashing 20 secnds after pwer indicating nrmal peratin. The SYS ERR LED will g n slid 15 secnds after pwer up. It will turn ff after 5 secnds. A steady red light will indicate there is a system errr n PrtNde. If this ccurs, immediately reprt the related system errr shwn in the errr screen f the GUI interface t FieldServer Technlgies fr evaluatin. The RX LED will flash when a message is received n the hst prt. The TX LED will flash when a message is sent n the hst prt. This is the pwer light and shuld shw steady green at all times when PrtNde is pwered. Figure 27: Diagnstic LEDs Appendix A.6. Passwrds Access t the PrtNde can be restricted by enabling a passwrd. There are 2 access levels defined by 2 accunt names: Admin and User. The Admin accunt has unrestricted access t the PrtNde. The User accunt can view any PrtNde infrmatin, but cannt make any changes r restart the PrtNde. The passwrd needs t be a minimum f eight characters and is case sensitive. If yu frgt yur passwrd, click cancel n the passwrd authenticatin ppup windw, and the Passwrd recvery tken t supprt@sierramnitr.cm t receive a temprary passwrd frm the Sierra Mnitr supprt team. Yu can nw access the PrtNde t set a new passwrd. Page 33 f 49

34 Appendix B. Additinal Features Appendix B.1. DIP switch settings t supprt Metasys N2 Nte: The lid n tp f the PrtNde has t be remved in rder t select the A Bank f DIP switches. Pull n the lid while hlding the n t the 6 pin Phenix cnnectr. Please d nt hld the wall munt tabs as these are designed t break ff if nt required! T set select these cnfiguratins, pen the PrtNde and select the A bank f switches (A1 r A2 r A3) n the small PrtCessr mdule that sits n tp f the PrtCarrier (inside the PrtNde). PrtCessr A1 DIP switch starts n the bttm f the A bank f DIP switches belw. PrtCessr A3-A8 DIP switches are disabled. S Bank DIP Switches A1, A2, and A3 DIP Switches Falcn N2 PrtCarrier DIP Switches PrtCessr DIP Switches (Remve Cver) Prfile - FPC-N S0 S1 S2 S3 A1 A2 A3 A4 A5 A6 A7 A8 Metasys N2 SYNC Deg_C Off Off On On Off Off Off Off Off Off Off Off Metasys N2 Knight/Knight XL/Armr/Wall Munt/Wall Hung Deg_C On Off On On Off Off Off Off Off Off Off Off Metasys N2 Crest Deg_C Off On On On Off Off Off Off Off Off Off Off Metasys N2 Cpper-Fin II Deg_C On On On On Off Off Off Off Off Off Off Off Metasys N2 Pwer Fin Deg_C Off Off Off Off On Off Off Off Off Off Off Off Metasys N2 Knight FTXL Deg_C On Off Off Off On Off Off Off Off Off Off Off Metasys N2 SYNC Deg_F Off On Off Off On Off Off Off Off Off Off Off Metasys N2 Knight/Knight XL/Armr/Wall Munt/Wall Hung Deg_F On On Off Off On Off Off Off Off Off Off Off Metasys N2 Crest Deg_F Off Off On Off On Off Off Off Off Off Off Off Metasys N2 Cpper-Fin II Deg_F On Off On Off On Off Off Off Off Off Off Off Metasys N2 Pwer Fin Deg_F Off On On Off On Off Off Off Off Off Off Off Metasys N2 Knight FTXL Deg_F On On On Off On Off Off Off Off Off Off Off Page 34 f 49

35 Appendix C. Vendr Infrmatin - Lchinvar Appendix C.1. Sync Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet Object Type BACnet Object ID N2 Data Type N2 Pint Address Ln Name Biler Enable/Rm Thermstat 1/Stg 1 BV 1 DO 1 i/blren_stg1 SNVT_switch Tank Thermstat BV 2 DO 2 i/tankthermstat SNVT_switch Manual Reset High Limit 1 BI 3 DI 3 ManResHiLim1 SNVT_switch Flw Switch 1 BI 4 DI 4 FLSw1 SNVT_switch Gas Pressure Switch 1 BI 5 DI 5 GasPrsSw1 SNVT_switch Luver Prving Switch 1 BI 6 DI 6 LuverPrvSw1 SNVT_switch Air Pressure Switch/Flap Vlv 1 BI 7 DI 7 AirPrsSwFlpVlv1 SNVT_switch Blcked Drain Switch 1 BI 8 DI 8 BlckedDrainSw1 SNVT_switch Aut Reset High Limit 1 BI 9 DI 9 AutResHiLim1 SNVT_switch Flame 1 BI 10 DI 10 Flame1 SNVT_switch Enable/Rm Thermstat 1/Stg 1 BI 11 DI 11 EnRmThermStg1 SNVT_switch Tank Thermstat BI 12 DI 12 TnkThermstat SNVT_switch Manual Reset High Limit 2 BI 13 DI 13 ManResHiLim2 SNVT_switch Flw Switch 2 BI 14 DI 14 FLSw2 SNVT_switch Gas Pressure Switch 2 BI 15 DI 15 GasPrsSw2 SNVT_switch Luver Prving Switch 2 BI 16 DI 16 LuverPrvSw2 SNVT_switch Air Pressure Switch/Flap Vlv 2 BI 17 DI 17 AirPrsSwFlpVlv2 SNVT_switch Blcked Drain Switch 2 BI 18 DI 18 BlckedDrainSw2 SNVT_switch Flame 2 BI 19 DI 19 Flame2 SNVT_switch Run-time Cntacts BI 20 DI 20 RunTimeCntcts SNVT_switch Alarm Cntacts 1 BI 21 DI 21 AlarmCntacts1 SNVT_switch CH Pump 1 BI 22 DI 22 CHPump1 SNVT_switch DHW Pump 1 BI 23 DI 23 DHWPump1 SNVT_switch Gas Vlv 1 BI 24 DI 24 GasVlv1 SNVT_switch System Pump BI 25 DI 25 SystemPump SNVT_switch Run-time Cntacts 2 BI 26 DI 26 RunTimeCntcts2 SNVT_switch Alarm Cntacts 2 BI 27 DI 27 AlarmCntacts2 SNVT_switch CH Pump 2 BI 28 DI 28 CHPump2 SNVT_switch Gas Vlv 2 BI 29 DI 29 GasVlv2 SNVT_switch Ln SNVT Page 35 f 49

36 Discrete Inputs 1-16 AI 30 AI 30 DiscInputs1_16 SNVT_cunt_f Discrete Inputs AI 31 AI 31 DiscInputs17_32 SNVT_cunt_f Discrete Inputs AI 32 AI 32 DiscInputs33_48 SNVT_cunt_f System/Cascade Setpint AI 33 AI 33 SysCascadeSP SNVT_temp_p Cascade Ttal Pwer AI 34 AI 34 CascadeTtalPwr SNVT_lev_percent Cascade Current Pwer AI 35 AI 35 CascadeCrrntPwr SNVT_lev_percent Outlet Setpint 1 AI 36 AI 36 OutletSP1 SNVT_temp_p Outlet Temperature 1 AI 37 AI 37 OutletTmp1 SNVT_temp_p Inlet Temperature 1 AI 38 AI 38 InletTmp1 SNVT_temp_p Flue Temperature 1 AI 39 AI 39 FlueTmp1 SNVT_temp_p Firing Rate 1 AI 40 AI 40 FiringRate1 SNVT_lev_percent Biler 1 Status Cde AI 41 AI 41 Blr1StatusCde SNVT_cunt_f Biler 1 Blcking Cde AI 42 AI 42 Blr1BlckngCde SNVT_cunt_f Biler 1 Lckut Cde AI 43 AI 43 Blr1LckutCde SNVT_cunt_f Outlet Setpint 2 AI 44 AI 44 OutletSP2 SNVT_temp_p Outlet Temperature 2 AI 45 AI 45 OutletTmp2 SNVT_temp_p Inlet Temperature 2 AI 46 AI 46 InletTmp2 SNVT_temp_p Flue Temperature 2 AI 47 AI 47 FlueTmp2 SNVT_temp_p Firing Rate 2 AI 48 AI 48 FiringRate2 SNVT_lev_percent Biler 2 Status Cde AI 49 AI 49 Blr2StatusCde SNVT_cunt_f Biler 2 Blcking Cde AI 50 AI 50 Blr2BlckngCde SNVT_cunt_f Biler 2 Lckut Cde AI 51 AI 51 Blr2LckutCde SNVT_cunt_f Cnfiguratin AV 52 AO 52 i/cnfiguratin SNVT_cunt_f Cils AV 53 AO 53 i/cils SNVT_cunt_f 0-10 Vlt Input/Rate Cmd/SP Cmd AV 54 AO 54 i/0_10vltinrtcmd SNVT_lev_percent Tank Setpint AV 55 AO 55 i/tanksp SNVT_temp_p Tank Temperature AV 56 AO 56 i/tanktmp SNVT_temp_p Outdr Temperature AV 57 AO 57 i/outdrtmp SNVT_temp_p System Supply Temperature AV 58 AO 58 i/syssupplytmp SNVT_temp_p Appendix C.2. Knight Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet Object Type BACnet Object ID N2 Data Type N2 Pint Address Ln Name Ln SNVT Page 36 f 49

37 Rm Thermstat 1 BV 1 DO 1 i/rmthermstat1 SNVT_switch Rm Thermstat 2 BV 2 DO 2 i/rmthermstat2 SNVT_switch Rm Thermstat 3 BV 3 DO 3 i/rmthermstat3 SNVT_switch Tank Thermstat BV 4 DO 4 i/tankthermstat SNVT_switch Flw Switch BI 5 DI 5 FlwSw SNVT_switch Gas Pressure Switch BI 6 DI 6 GasPressureSw SNVT_switch Luver Prving Switch BI 7 DI 7 LuverPrvingSw SNVT_switch Air Pressure Switch BI 8 DI 8 AirPressureSw SNVT_switch Blcked Drain Switch BI 9 DI 9 BlckedDrainSw SNVT_switch Aut Reset High Limit BI 10 DI 10 AutResetHiLim SNVT_switch Flame BI 11 DI 11 Flame SNVT_switch Rm Thermstat 1 BI 12 DI 12 RmThrmstat1 SNVT_switch Tank Thermstat BI 13 DI 13 TnkThrmstat SNVT_switch Rm Thermstat 2 BI 14 DI 14 RmThrmstat2 SNVT_switch Run-time Cntacts BI 15 DI 15 RunTimeCntacts SNVT_switch Alarm Cntacts BI 16 DI 16 AlarmCntacts SNVT_switch CH Pump BI 17 DI 17 CHPump SNVT_switch DHW Pump BI 18 DI 18 DHWPump SNVT_switch Gas Valve BI 19 DI 19 GasValve SNVT_switch System Pump BI 20 DI 20 SystemPump SNVT_switch Discrete Inputs 1-16 AI 21 AI 21 DiscInputs1-16 SNVT_cunt_f Discrete Inputs AI 22 AI 22 DiscInputs17-32 SNVT_cunt_f Discrete Inputs AI 23 AI 23 DiscInputs33-48 SNVT_cunt_f System Cascade Setpint AI 24 AI 24 SystemCascadeSP SNVT_temp_p System Pump Speed AI 25 AI 25 SystemPumpSpeed SNVT_lev_percent Cascade Ttal Pwer AI 26 AI 26 CascadeTtalPwr SNVT_lev_percent Cascade Current Pwer AI 27 AI 27 CascadeCrrntPwr SNVT_lev_percent Outlet Setpint AI 28 AI 28 OutletSP SNVT_temp_p Outlet Temperature AI 29 AI 29 OutletTmp SNVT_temp_p Inlet Temperature AI 30 AI 30 InletTmp SNVT_temp_p Flue Temperature AI 31 AI 31 FlueTmp SNVT_temp_p Firing Rate AI 32 AI 32 FiringRate SNVT_lev_percent Biler Pump Speed AI 33 AI 33 BlrPumpSpeed SNVT_lev_percent Biler Status Cde AI 34 AI 34 BlrStatusCde SNVT_cunt_f Biler Blcking Cde AI 35 AI 35 BlrBlckingCde SNVT_cunt_f Page 37 f 49

38 Biler Lckut Cde AI 36 AI 36 BlrLckutCde SNVT_cunt_f Cnfiguratin AV 37 AO 37 i/cnfiguratin SNVT_cunt_f Cils AV 38 AO 38 i/cils SNVT_cunt_f 0-10 Vlt Input/Rate Cmd/SP Cmd AV 39 AO 39 i/0_10vltinrtcmd SNVT_lev_percent Tank Setpint AV 40 AO 40 i/tanksp SNVT_temp_p Tank Temperature AV 41 AO 41 i/tanktmp SNVT_temp_p Outdr Temperature AV 42 AO 42 i/outdrtmp SNVT_temp_p System Supply Temperature AV 43 AO 43 i/systemsupplytmp SNVT_temp_p System Return Temperature AV 44 AO 44 i/systemreturntmp SNVT_temp_p Appendix C.3. Crest Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet Object Type BACnet Object ID N2 Data Type N2 Pint Address Ln Name Biler Enable BV 1 DO 1 nvi/nvbilerenable SNVT_switch Tank Thermstat BV 2 DO 2 nvi/nvtnkthermstat SNVT_switch Manual Reset High Limit BI 3 DI 3 nvmanresethilim SNVT_switch Flw Switch BI 4 DI 4 nvflwsw SNVT_switch Gas Pressure Switch BI 5 DI 5 nvgasprssw SNVT_switch Luvers Prving Switch BI 6 DI 6 nvluversprvsw SNVT_switch Blwer Prving Switch 1 BI 7 DI 7 nvblwrprvsw1 SNVT_switch Blcked Drain Switch BI 8 DI 8 nvblkdrainsw SNVT_switch Flame 1 BI 9 DI 9 nvflame1 SNVT_switch Enable BI 10 DI 10 nvenable SNVT_switch Tank Thermstat BI 11 DI 11 nvtnkthrmstat SNVT_switch Blcked Flue BI 12 DI 12 nvblckedflue SNVT_switch Blwer Prving Switch 2 BI 13 DI 13 nvblwrprvsw2 SNVT_switch Flue Damper Prving Switch BI 14 DI 14 nvfluedmprprvsw SNVT_switch Flame 2 BI 15 DI 15 nvflame2 SNVT_switch Run Time Cntacts BI 16 DI 16 nvruntimcntcts SNVT_switch Alarm Cntacts BI 17 DI 17 nvalarmcntacts SNVT_switch SH Pump BI 18 DI 18 nvshpump SNVT_switch HWG Pump BI 19 DI 19 nvhwgpump SNVT_switch Luver Relay BI 20 DI 20 nvluverrel SNVT_switch Ln SNVT Page 38 f 49

39 Gas Valve 1 BI 21 DI 21 nvgasvlv1 SNVT_switch System Pump BI 22 DI 22 nvsyspump SNVT_switch Vent Damper Relay BI 23 DI 23 nvventdmprrel SNVT_switch Gas Valve 2 BI 24 DI 24 nvgasvlv2 SNVT_switch Blwer #1 Pwer BI 25 DI 25 nvblwr#1pwr SNVT_switch Blwer #2 Pwer BI 26 DI 26 nvblwr#2pwr SNVT_switch Spark Igniter BI 27 DI 27 nvsparkigniter SNVT_switch Transitin Gas Valve BI 28 DI 28 nvtrangasvlv SNVT_switch Air Valve Trigger BI 29 DI 29 nvairvlvtrg SNVT_switch Air Valve Prving BI 30 DI 30 nvairvlvprv SNVT_switch Discrete Inputs AI 31 AI 31 nvdi_01_16 SNVT_cunt_f Discrete Inputs AI 32 AI 32 nvdi_17_32 SNVT_cunt_f Discrete Inputs AI 33 AI 33 nvdi_33_48 SNVT_cunt_f System Cascade Setpint AI 34 AI 34 nvsyscascadesp SNVT_temp_p System Pump Speed In AI 35 AI 35 nvsyspumpspdin SNVT_lev_percent Cascade Ttal Pwer AI 36 AI 36 nvcascdttpwr SNVT_lev_percent Cascade Current Pwer AI 37 AI 37 nvcascdcrntpwr SNVT_lev_percent Outlet Setpint AI 38 AI 38 nvoutletsp SNVT_temp_p Outlet Temperature AI 39 AI 39 nvoutlettmp SNVT_temp_p Inlet Temperature AI 40 AI 40 nvinlettmp SNVT_temp_p Flue Temperature AI 41 AI 41 nvfluetmp SNVT_temp_p Firing Rate AI 42 AI 42 nvfiringrate SNVT_lev_percent Biler Pump Speed Out AI 43 AI 43 nvblrpmpspdout SNVT_lev_percent Biler Status Cde AI 44 AI 44 nvblrstatuscde SNVT_cunt_f Biler Blcking Cde AI 45 AI 45 nvblrblckngcde SNVT_cunt_f Biler Lck Out Cde AI 46 AI 46 nvblrlckoutcde SNVT_cunt_f Discrete Inputs AI 47 AI 47 nvdi_49_64 SNVT_cunt_f Lckut Errr Leader AI 48 AI 48 nvlckouterrldr SNVT_cunt_f Lckut Errr Member 1 AI 49 AI 49 nvlckouterrm1 SNVT_cunt_f Lckut Errr Member 2 AI 50 AI 50 nvlckouterrm2 SNVT_cunt_f Lckut Errr Member 3 AI 51 AI 51 nvlckouterrm3 SNVT_cunt_f Lckut Errr Member 4 AI 52 AI 52 nvlckouterrm4 SNVT_cunt_f Lckut Errr Member 5 AI 53 AI 53 nvlckouterrm5 SNVT_cunt_f Lckut Errr Member 6 AI 54 AI 54 nvlckouterrm6 SNVT_cunt_f Lckut Errr Member 7 AI 55 AI 55 nvlckouterrm7 SNVT_cunt_f Page 39 f 49

40 Cnfiguratin AV 56 AO 56 nvi/nvcnfiguratin SNVT_cunt_f Cils AV 57 AO 57 nvi/nvcils SNVT_cunt_f 0-10 Vlt Input AV 58 AO 58 nvi/nv0_10vltinput SNVT_lev_percent Tank Setpint AV 59 AO 59 nvi/nvtnksp SNVT_temp_p Tank Temperature AV 60 AO 60 nvi/nvtnktmp SNVT_temp_p Outdr Temperature AV 61 AO 61 nvi/nvoutdrtmp SNVT_temp_p System Supply Temperature AV 62 AO 62 nvi/nvsyssupplytmp SNVT_temp_p System Return Temperature AV 63 AO 63 nvi/nvsysreturntmp SNVT_temp_p Appendix C.4. Cpper-Fin II Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet Object Type BACnet Object ID N2 Data Type N2 Pint Address Ln Name Stage 1 Enable BV 1 DO 1 nvi/nvstg1enable SNVT_switch Stage 2 Enable BV 2 DO 2 nvi/nvstg2enable SNVT_switch Stage 3 Enable BV 3 DO 3 nvi/nvstg3enable SNVT_switch Stage 4 Enable BV 4 DO 4 nvi/nvstg4enable SNVT_switch Tank Thermstat BV 5 DO 5 nvi/nvtankthrmstat SNVT_switch High Limits BI 6 DI 6 nvhilimits SNVT_switch Flw Switch BI 7 DI 7 nvflwsw SNVT_switch Gas Pressure Switch BI 8 DI 8 nvgaspressw SNVT_switch Luver Prving Switch BI 9 DI 9 nvluverprvsw SNVT_switch Air Pressure Switch BI 10 DI 10 nvairpressw SNVT_switch Flame 1 BI 11 DI 11 nvflame1 SNVT_switch Stage 1 On BI 12 DI 12 nvstg1on SNVT_switch Tank Thermstat BI 13 DI 13 nvtnkthrmstat SNVT_switch Stage 2 On BI 14 DI 14 nvstg2on SNVT_switch Stage 3 On BI 15 DI 15 nvstg3on SNVT_switch Stage 4 On BI 16 DI 16 nvstg4on SNVT_switch Flame 2 BI 17 DI 17 nvflame2 SNVT_switch Enable 2 BI 18 DI 18 nvenable2 SNVT_switch Run Time Cntacts BI 19 DI 19 nvruntimcntct SNVT_switch Alarm Cntacts BI 20 DI 20 nvalarmcntact SNVT_switch HTR Pump BI 21 DI 21 nvhtrpump SNVT_switch Ln SNVT Page 40 f 49

41 DHW Pump BI 22 DI 22 nvdhwpump SNVT_switch Luver Relay BI 23 DI 23 nvluverrelay SNVT_switch Gas Valve 1 BI 24 DI 24 nvgasvalve1 SNVT_switch System Pump BI 25 DI 25 nvsyspump SNVT_switch Gas Valve 2 BI 26 DI 26 nvgasvalve2 SNVT_switch Gas Valve 3 BI 27 DI 27 nvgasvalve3 SNVT_switch Gas Valve 4 BI 28 DI 28 nvgasvalve4 SNVT_switch Discrete Inputs AI 29 AI 29 nvdi_01_16 SNVT_cunt_f Discrete Inputs AI 30 AI 30 nvdi_17_32 SNVT_cunt_f Discrete Inputs AI 31 AI 31 nvdi_33_48 SNVT_cunt_f System Cascade Setpint AI 32 AI 32 nvsyscascadesp SNVT_temp_p System Pump Speed AI 33 AI 33 nvsyspumpspeed SNVT_lev_percent Cascade Ttal Pwer AI 34 AI 34 nvcascdttpwr SNVT_lev_percent Cascade Current Pwer AI 35 AI 35 nvcascdcrntpwr SNVT_lev_percent Outlet Setpint AI 36 AI 36 nvoutletsp SNVT_temp_p Outlet Temperature AI 37 AI 37 nvoutlettmp SNVT_temp_p Inlet Temperature AI 38 AI 38 nvinlettmp SNVT_temp_p Pl Temperature AI 39 AI 39 nvpltmp SNVT_temp_p Firing Rate AI 40 AI 40 nvfiringrate SNVT_lev_percent Biler Status Cde AI 41 AI 41 nvblrstatuscde SNVT_cunt_f Biler Blcking Cde AI 42 AI 42 nvblrblckngcde SNVT_cunt_f Biler Lckut Cde AI 43 AI 43 nvblrlckoutcde SNVT_cunt_f Cnfiguratin AV 45 AO 45 nvi/nvcnfiguratin SNVT_cunt_f Cils AV 46 AO 46 nvi/nvcils SNVT_cunt_f 0-10 Vlt Input AV 47 AO 47 nvi/nv0_10vltinput SNVT_lev_percent Pl Setpint AV 48 AO 48 nvi/nvplsetpint SNVT_temp_p Tank Temperature AV 49 AO 49 nvi/nvtanktmp SNVT_temp_p Outdr Temperature AV 50 AO 50 nvi/nvoutdrtmp SNVT_temp_p System Supply Temperature AV 51 AO 51 nvi/nvsyssupplytmp SNVT_temp_p System Return Temperature AV 52 AO 52 nvi/nvsysreturntmp SNVT_temp_p Appendix C.5. Pwer Fin Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet BACnet N2 Data N2 Ln Name Ln SNVT Page 41 f 49

42 Object Type Object ID Type Pint Address Biler Enable/Rm Thermstat 1/Stg 1 BV 1 DO 1 i/blren_stg1 SNVT_switch Tank Thermstat BV 2 DO 2 i/tankthermstat SNVT_switch Manual Reset High Limit 1 BI 3 DI 3 ManResHiLim1 SNVT_switch Flw Switch 1 BI 4 DI 4 FLSw1 SNVT_switch Gas Pressure Switch 1 BI 5 DI 5 GasPrsSw1 SNVT_switch Luver Prving Switch 1 BI 6 DI 6 LuverPrvSw1 SNVT_switch Air Pressure Switch/Flap Vlv 1 BI 7 DI 7 AirPrsSwFlpVlv1 SNVT_switch Blcked Drain Switch 1 BI 8 DI 8 BlckedDrainSw1 SNVT_switch Aut Reset High Limit 1 BI 9 DI 9 AutResHiLim1 SNVT_switch Flame 1 BI 10 DI 10 Flame1 SNVT_switch Enable/Rm Thermstat 1/Stg 1 BI 11 DI 11 EnRmThermStg1 SNVT_switch Tank Thermstat BI 12 DI 12 TnkThermstat SNVT_switch Run-time Cntacts BI 13 DI 13 RunTimeCntcts SNVT_switch Alarm Cntacts 1 BI 14 DI 14 AlarmCntacts1 SNVT_switch CH Pump 1 BI 15 DI 15 CHPump1 SNVT_switch DHW Pump 1 BI 16 DI 16 DHWPump1 SNVT_switch Gas Vlv 1 BI 17 DI 17 GasVlv1 SNVT_switch System Pump BI 18 DI 18 SystemPump SNVT_switch Mains Fan 1 BI 19 DI 19 MainsFan1 SNVT_switch External Spark BI 20 DI 20 ExtSpark SNVT_switch Discrete Inputs 1-16 AI 21 AI 21 DiscInputs1_16 SNVT_cunt_f Discrete Inputs AI 22 AI 22 DiscInputs17_32 SNVT_cunt_f Discrete Inputs AI 23 AI 23 DiscInputs33_48 SNVT_cunt_f System/Cascade Setpint AI 24 AI 24 SysCascadeSP SNVT_temp_p Cascade Ttal Pwer AI 25 AI 25 CascadeTtalPwr SNVT_lev_percent Cascade Current Pwer AI 26 AI 26 CascadeCrrntPwr SNVT_lev_percent Outlet Setpint 1 AI 27 AI 27 OutletSP1 SNVT_temp_p Outlet Temperature 1 AI 28 AI 28 OutletTmp1 SNVT_temp_p Inlet Temperature 1 AI 29 AI 29 InletTmp1 SNVT_temp_p Flue Temperature 1 AI 30 AI 30 FlueTmp1 SNVT_temp_p Firing Rate 1 AI 31 AI 31 FiringRate1 SNVT_lev_percent Biler 1 Status Cde AI 32 AI 32 Blr1StatusCde SNVT_cunt_f Biler 1 Blcking Cde AI 33 AI 33 Blr1BlckngCde SNVT_cunt_f Biler 1 Lckut Cde AI 34 AI 34 Blr1LckutCde SNVT_cunt_f Page 42 f 49

43 Discrete Inputs AI 35 AI 35 DiscInputs49_64 SNVT_cunt_f Cnfiguratin AV 36 AO 36 i/cnfiguratin SNVT_cunt_f Cils AV 37 AO 37 i/cils SNVT_cunt_f 0-10 Vlt Input/Rate Cmd/SP Cmd AV 38 AO 38 i/0_10vltinrtcmd SNVT_lev_percent Tank Setpint AV 39 AO 39 i/tanksp SNVT_temp_p Tank Temperature AV 40 AO 40 i/tanktmp SNVT_temp_p Outdr Temperature AV 41 AO 41 i/outdrtmp SNVT_temp_p System Supply Temperature AV 42 AO 42 i/syssupplytmp SNVT_temp_p System Return Temperature AV 43 AO 43 i/sysreturntmp SNVT_temp_p Appendix C.6. Knight FTXL Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet Object Type BACnet Object ID N2 Data Type N2 Pint Address Ln Name Rm Thermstat 1 BV 1 DO 1 i/rmthermstat1 SNVT_switch Rm Thermstat 2 BV 2 DO 2 i/rmthermstat2 SNVT_switch Rm Thermstat 3 BV 3 DO 3 i/rmthermstat3 SNVT_switch Tank Thermstat BV 4 DO 4 i/tankthermstat SNVT_switch Flw Switch BI 5 DI 5 FlwSw SNVT_switch Gas Pressure Switch BI 6 DI 6 GasPressureSw SNVT_switch Luver Prving Switch BI 7 DI 7 LuverPrvingSw SNVT_switch Air Pressure Switch BI 8 DI 8 AirPressureSw SNVT_switch Blcked Drain Switch BI 9 DI 9 BlckedDrainSw SNVT_switch Aut Reset High Limit BI 10 DI 10 AutResetHiLim SNVT_switch Flame BI 11 DI 11 Flame SNVT_switch Rm Thermstat 1 BI 12 DI 12 RmThrmstat1 SNVT_switch Tank Thermstat BI 13 DI 13 TnkThrmstat SNVT_switch Rm Thermstat 2 BI 14 DI 14 RmThrmstat2 SNVT_switch Run-time Cntacts BI 15 DI 15 RunTimeCntacts SNVT_switch Alarm Cntacts BI 16 DI 16 AlarmCntacts SNVT_switch CH Pump BI 17 DI 17 CHPump SNVT_switch DHW Pump 1 BI 18 DI 18 DHWPump1 SNVT_switch Luver Relay BI 19 DI 19 LuverRelay SNVT_switch Gas Valve BI 20 DI 20 GasValve SNVT_switch Ln SNVT Page 43 f 49

44 System Pump BI 21 DI 21 SystemPump SNVT_switch DHW Pump 2 BI 22 DI 22 DHWPump2 SNVT_switch Discrete Inputs 1-16 AI 23 AI 23 DiscInputs1-16 SNVT_cunt_f Discrete Inputs AI 24 AI 24 DiscInputs17-32 SNVT_cunt_f Discrete Inputs AI 25 AI 25 DiscInputs33-48 SNVT_cunt_f System Cascade Setpint AI 26 AI 26 SystemCascadeSP SNVT_temp_p System Pump Speed AI 27 AI 27 SystemPumpSpeed SNVT_lev_percent Cascade Ttal Pwer AI 28 AI 28 CascadeTtalPwr SNVT_lev_percent Cascade Current Pwer AI 29 AI 29 CascadeCrrntPwr SNVT_lev_percent Outlet Setpint AI 30 AI 30 OutletSP SNVT_temp_p Outlet Temperature AI 31 AI 31 OutletTmp SNVT_temp_p Inlet Temperature AI 32 AI 32 InletTmp SNVT_temp_p Flue Temperature AI 33 AI 33 FlueTmp SNVT_temp_p Firing Rate AI 34 AI 34 FiringRate SNVT_lev_percent Biler Pump Speed AI 35 AI 35 BlrPumpSpeed SNVT_lev_percent Biler Status Cde AI 36 AI 36 BlrStatusCde SNVT_cunt_f Biler Blcking Cde AI 37 AI 37 BlrBlckingCde SNVT_cunt_f Biler Lckut Cde AI 38 AI 38 BlrLckutCde SNVT_cunt_f Cnfiguratin AV 39 AO 39 i/cnfiguratin SNVT_cunt_f Cils AV 40 AO 40 i/cils SNVT_cunt_f 0-10 Vlt Input/Rate Cmd/SP Cmd AV 41 AO 41 i/0_10vltinrtcmd SNVT_lev_percent Tank Setpint AV 42 AO 42 i/tanksp SNVT_temp_p Tank Temperature AV 43 AO 43 i/tanktmp SNVT_temp_p Outdr Temperature AV 44 AO 44 i/outdrtmp SNVT_temp_p System Supply Temperature AV 45 AO 45 i/systemsupplytmp SNVT_temp_p System Return Temperature AV 46 AO 46 i/systemreturntmp SNVT_temp_p Page 44 f 49

45 Appendix D. A Bank DIP Switch Settings Appendix D.1. A Bank DIP Switch Settings Address A0 A1 A2 A3 A4 A5 A6 A7 1 On Off Off Off Off Off Off Off 2 Off On Off Off Off Off Off Off 3 On On Off Off Off Off Off Off 4 Off Off On Off Off Off Off Off 5 On Off On Off Off Off Off Off 6 Off On On Off Off Off Off Off 7 On On On Off Off Off Off Off 8 Off Off Off On Off Off Off Off 9 On Off Off On Off Off Off Off 10 Off On Off On Off Off Off Off 11 On On Off On Off Off Off Off 12 Off Off On On Off Off Off Off 13 On Off On On Off Off Off Off 14 Off On On On Off Off Off Off 15 On On On On Off Off Off Off 16 Off Off Off Off On Off Off Off 17 On Off Off Off On Off Off Off 18 Off On Off Off On Off Off Off 19 On On Off Off On Off Off Off 20 Off Off On Off On Off Off Off 21 On Off On Off On Off Off Off 22 Off On On Off On Off Off Off 23 On On On Off On Off Off Off 24 Off Off Off On On Off Off Off 25 On Off Off On On Off Off Off 26 Off On Off On On Off Off Off 27 On On Off On On Off Off Off 28 Off Off On On On Off Off Off 29 On Off On On On Off Off Off 30 Off On On On On Off Off Off 31 On On On On On Off Off Off 32 Off Off Off Off Off On Off Off 33 On Off Off Off Off On Off Off 34 Off On Off Off Off On Off Off 35 On On Off Off Off On Off Off 36 Off Off On Off Off On Off Off 37 On Off On Off Off On Off Off 38 Off On On Off Off On Off Off 39 On On On Off Off On Off Off 40 Off Off Off On Off On Off Off 41 On Off Off On Off On Off Off 42 Off On Off On Off On Off Off 43 On On Off On Off On Off Off 44 Off Off On On Off On Off Off 45 On Off On On Off On Off Off Address A0 A1 A2 A3 A4 A5 A6 A7 46 Off On On On Off On Off Off 47 On On On On Off On Off Off 48 Off Off Off Off On On Off Off 49 On Off Off Off On On Off Off 50 Off On Off Off On On Off Off 51 On On Off Off On On Off Off 52 Off Off On Off On On Off Off 53 On Off On Off On On Off Off 54 Off On On Off On On Off Off 55 On On On Off On On Off Off 56 Off Off Off On On On Off Off 57 On Off Off On On On Off Off 58 Off On Off On On On Off Off 59 On On Off On On On Off Off 60 Off Off On On On On Off Off 61 On Off On On On On Off Off 62 Off On On On On On Off Off 63 On On On On On On Off Off 64 Off Off Off Off Off Off On Off 65 On Off Off Off Off Off On Off 66 Off On Off Off Off Off On Off 67 On On Off Off Off Off On Off 68 Off Off On Off Off Off On Off 69 On Off On Off Off Off On Off 70 Off On On Off Off Off On Off 71 On On On Off Off Off On Off 72 Off Off Off On Off Off On Off 73 On Off Off On Off Off On Off 74 Off On Off On Off Off On Off 75 On On Off On Off Off On Off 76 Off Off On On Off Off On Off 77 On Off On On Off Off On Off 78 Off On On On Off Off On Off 79 On On On On Off Off On Off 80 Off Off Off Off On Off On Off 81 On Off Off Off On Off On Off 82 Off On Off Off On Off On Off 83 On On Off Off On Off On Off 84 Off Off On Off On Off On Off 85 On Off On Off On Off On Off 86 Off On On Off On Off On Off 87 On On On Off On Off On Off 88 Off Off Off On On Off On Off 89 On Off Off On On Off On Off 90 Off On Off On On Off On Off Page 45 f 49

46 Address A0 A1 A2 A3 A4 A5 A6 A7 91 On On Off On On Off On Off 92 Off Off On On On Off On Off 93 On Off On On On Off On Off 94 Off On On On On Off On Off 95 On On On On On Off On Off 96 Off Off Off Off Off On On Off 97 On Off Off Off Off On On Off 98 Off On Off Off Off On On Off 99 On On Off Off Off On On Off 100 Off Off On Off Off On On Off 101 On Off On Off Off On On Off 102 Off On On Off Off On On Off 103 On On On Off Off On On Off 104 Off Off Off On Off On On Off 105 On Off Off On Off On On Off 106 Off On Off On Off On On Off 107 On On Off On Off On On Off 108 Off Off On On Off On On Off 109 On Off On On Off On On Off 110 Off On On On Off On On Off 111 On On On On Off On On Off 112 Off Off Off Off On On On Off 113 On Off Off Off On On On Off 114 Off On Off Off On On On Off 115 On On Off Off On On On Off 116 Off Off On Off On On On Off 117 On Off On Off On On On Off 118 Off On On Off On On On Off 119 On On On Off On On On Off 120 Off Off Off On On On On Off 121 On Off Off On On On On Off 122 Off On Off On On On On Off 123 On On Off On On On On Off 124 Off Off On On On On On Off 125 On Off On On On On On Off 126 Off On On On On On On Off 127 On On On On On On On Off 128 Off Off Off Off Off Off Off On 129 On Off Off Off Off Off Off On 130 Off On Off Off Off Off Off On 131 On On Off Off Off Off Off On 132 Off Off On Off Off Off Off On 133 On Off On Off Off Off Off On 134 Off On On Off Off Off Off On 135 On On On Off Off Off Off On 136 Off Off Off On Off Off Off On 137 On Off Off On Off Off Off On 138 Off On Off On Off Off Off On Address A0 A1 A2 A3 A4 A5 A6 A7 139 On On Off On Off Off Off On 140 Off Off On On Off Off Off On 141 On Off On On Off Off Off On 142 Off On On On Off Off Off On 143 On On On On Off Off Off On 144 Off Off Off Off On Off Off On 145 On Off Off Off On Off Off On 146 Off On Off Off On Off Off On 147 On On Off Off On Off Off On 148 Off Off On Off On Off Off On 149 On Off On Off On Off Off On 150 Off On On Off On Off Off On 151 On On On Off On Off Off On 152 Off Off Off On On Off Off On 153 On Off Off On On Off Off On 154 Off On Off On On Off Off On 155 On On Off On On Off Off On 156 Off Off On On On Off Off On 157 On Off On On On Off Off On 158 Off On On On On Off Off On 159 On On On On On Off Off On 160 Off Off Off Off Off On Off On 161 On Off Off Off Off On Off On 162 Off On Off Off Off On Off On 163 On On Off Off Off On Off On 164 Off Off On Off Off On Off On 165 On Off On Off Off On Off On 166 Off On On Off Off On Off On 167 On On On Off Off On Off On 168 Off Off Off On Off On Off On 169 On Off Off On Off On Off On 170 Off On Off On Off On Off On 171 On On Off On Off On Off On 172 Off Off On On Off On Off On 173 On Off On On Off On Off On 174 Off On On On Off On Off On 175 On On On On Off On Off On 176 Off Off Off Off On On Off On 177 On Off Off Off On On Off On 178 Off On Off Off On On Off On 179 On On Off Off On On Off On 180 Off Off On Off On On Off On 181 On Off On Off On On Off On 182 Off On On Off On On Off On 183 On On On Off On On Off On 184 Off Off Off On On On Off On 185 On Off Off On On On Off On 186 Off On Off On On On Off On Page 46 f 49

47 Address A0 A1 A2 A3 A4 A5 A6 A7 187 On On Off On On On Off On 188 Off Off On On On On Off On 189 On Off On On On On Off On 190 Off On On On On On Off On 191 On On On On On On Off On 192 Off Off Off Off Off Off On On 193 On Off Off Off Off Off On On 194 Off On Off Off Off Off On On 195 On On Off Off Off Off On On 196 Off Off On Off Off Off On On 197 On Off On Off Off Off On On 198 Off On On Off Off Off On On 199 On On On Off Off Off On On 200 Off Off Off On Off Off On On 201 On Off Off On Off Off On On 202 Off On Off On Off Off On On 203 On On Off On Off Off On On 204 Off Off On On Off Off On On 205 On Off On On Off Off On On 206 Off On On On Off Off On On 207 On On On On Off Off On On 208 Off Off Off Off On Off On On 209 On Off Off Off On Off On On 210 Off On Off Off On Off On On 211 On On Off Off On Off On On 212 Off Off On Off On Off On On 213 On Off On Off On Off On On 214 Off On On Off On Off On On 215 On On On Off On Off On On 216 Off Off Off On On Off On On 217 On Off Off On On Off On On 218 Off On Off On On Off On On 219 On On Off On On Off On On 220 Off Off On On On Off On On 221 On Off On On On Off On On 222 Off On On On On Off On On 223 On On On On On Off On On 224 Off Off Off Off Off On On On 225 On Off Off Off Off On On On 226 Off On Off Off Off On On On 227 On On Off Off Off On On On 228 Off Off On Off Off On On On 229 On Off On Off Off On On On 230 Off On On Off Off On On On 231 On On On Off Off On On On 232 Off Off Off On Off On On On 233 On Off Off On Off On On On 234 Off On Off On Off On On On Address A0 A1 A2 A3 A4 A5 A6 A7 235 On On Off On Off On On On 236 Off Off On On Off On On On 237 On Off On On Off On On On 238 Off On On On Off On On On 239 On On On On Off On On On 240 Off Off Off Off On On On On 241 On Off Off Off On On On On 242 Off On Off Off On On On On 243 On On Off Off On On On On 244 Off Off On Off On On On On 245 On Off On Off On On On On 246 Off On On Off On On On On 247 On On On Off On On On On 248 Off Off Off On On On On On 249 On Off Off On On On On On 250 Off On Off On On On On On 251 On On Off On On On On On 252 Off Off On On On On On On 253 On Off On On On On On On 254 Off On On On On On On On 255 On On On On On On On On Page 47 f 49

48 Appendix E. Reference Appendix E.1. Specificatins Electrical Cnnectins Apprvals: PrtNde FPC-N34 One 6-pin Phenix cnnectr with: RS-485 prt (+ / - / gnd) Pwer prt (+ / - / Frame-gnd) One 3-pin Phenix cnnectr with: RS-485 prt (+ / - / gnd) One Ethernet 10/100 BaseT prt PrtNde FPC-N35 One 6-pin Phenix cnnectr with: RS-485 prt (+ / - / gnd) Pwer prt (+ / - / Frame-gnd) One Ethernet 10/100 BaseT prt One FTT-10 LnWrks prt CE Certified; TUV apprved t UL 916, EN , EN and CSA C22-2 standards; FCC Class A Part 15; DNP3 Cnfrmance Tested; RHS Cmpliant; CSA 205 Apprved BTL Marked LnMark Certified Multi-mde pwer adapter: 9-30VDC r 12-24VAC 11.5 cm L x 8.3 cm W x 4.1 cm H (4.5 x 3.2 x 1.6 in.) 0.2 kg (0.4 lbs) Pwer Requirements Physical Dimensins Weight: Operating -40 C t 75 C (-40 F t167 F) Temperature: Surge Suppressin Humidity: 5-90% RH (nn-cndensing) (Specificatins subject t change withut ntice) EN ESD EN EMC EN EFT Figure 28: Specificatins Appendix E.1.1. Cmpliance with UL Regulatins Fr UL cmpliance, the fllwing instructins must be met when perating PrtNde. The units shall be pwered by listed LPS r Class 2 pwer supply suited t the expected perating temperature range. The intercnnecting pwer cnnectr and pwer cable shall: Cmply with lcal electrical cde. Be suited t the expected perating temperature range. Meet the current and vltage rating fr PrtNde/Net Furthermre, the intercnnecting pwer cable shall: Be f length nt exceeding 3.05m (118.3 ) Be cnstructed f materials rated VW-1 r FT-1 r better If the unit is t be installed in an perating envirnment with a temperature abve 65 C, it shuld be installed in a Restricted Access Area requiring a key r a special tl t gain access This device must nt be cnnected t a LAN segment with utdr wiring. Page 48 f 49