APPLICABILITY & EFFECTIVITY

Transcription

1 PrtNde FPC-N34 and PrtNde FPC-N35 Startup Guide Fr Interfacing Triangle Tube Prducts: Prestige and Keystne T Building Autmatin Systems: BACnet MS/TP, BACnet/IP, Mdbus/TCP, Metasys N2 and LnWrks APPLICABILITY & EFFECTIVITY Explains PrtNde FPC-N34 and FPC-N35 hardware and hw t install it. The instructins are effective fr the abve as f May 2014 Date 6/9/ E10 PrtNde Startup

2 Triangle Tube s PrtNde Startup Guide Page 2 f 40 Technical Supprt: Thank yu fr purchasing the PrtNde fr Triangle Tube. Please call Triangle Tube fr Technical supprt f the PrtNde prduct. FieldServer des nt prvide direct supprt. If Triangle Tube needs t escalate the cncern, they will cntact FieldServer fr assistance. Supprt Cntact Infrmatin: ACV - Triangle Tube 1 Triangle Lane Blackwd, NJ Triangle Tube Service: (856) Website:

3 Triangle Tube s PrtNde Startup Guide Page 3 f 40 Quick Start Guide 1. Recrd the infrmatin abut the unit. (Sectin 2.1) 2. Set the device s Mdbus Address fr each f the devices that will be cnnected t PrtNde FPC-N34 r FPC-N35. (Sectin 2.2.2) 3. Select a stred cnfiguratin and set field prtcl MAC address/nde-id/device Instance, and baud rate. (Sectin 2.3) 4. Cnnect PrtNde s 6 pin RS-485 cnnectr t the Mdbus RS-485 netwrk that is cnnected t each f the devices. (Sectin 3.2) 5. Cnnect FPC-N34 PrtNde s 3 pin RS-485 prt t the Field Prtcl cabling (Sectin 3.3), r cnnect FPC-N35 PrtNde s 2 pin LnWrks prt t the Field Prtcl cabling. (Sectin 3.4) 6. Cnnect Pwer t PrtNde s 6 pin cnnectr. (Sectin 3.5) 7. BACnet/IP r Mdbus/TCP (FPC-N34): Use the PrtNde s embedded tl which is accessed with a brwser, referred t in this manual as the Web Cnfiguratr, t change the IP address. N changes t the cnfiguratin file are necessary. (Sectin 4) 8. LnWrks (FPC-N35): The PrtNde must be cmmissined n the LnWrks Netwrk. This needs t be dne by the LnWrks administratr using a LnWrks Cmmissining tl. (Sectin 5)

4 Triangle Tube s PrtNde Startup Guide Page 4 f 40 Certificatins BTL MARK BACNET TESTING LABORATORY The BTL Mark n PrtNde FPC-N34 is a symbl that indicates that a prduct has passed a series f rigrus tests cnducted by an independent labratry which verifies that the prduct crrectly implements the BACnet features claimed in the listing. The mark is a symbl f a high-quality BACnet prduct. G t fr mre infrmatin abut the BACnet Testing Labratry. LONMARK CERTIFICATION LnMark Internatinal is the recgnized authrity fr certificatin, educatin, and prmtin f interperability standards fr the benefit f manufacturers, integratrs and end users. LnMark Internatinal has develped extensive prduct certificatin standards and tests t prvide the integratr and user with cnfidence that prducts frm multiple manufacturers utilizing LnMark devices wrk tgether. FieldServer Technlgies has mre LnMark Certified gateways than any ther gateway manufacturer, including the PrtCessr, PrtCarrier and PrtNde fr OEM applicatins and the full featured, cnfigurable gateways.

5 Triangle Tube s PrtNde Startup Guide Page 5 f 40 TABLE OF CONTENTS 1 Intrductin PrtNde Gateway BACnet/LnWrks Setup fr PrtCessr PrtNde FPC-N34/FPC-N Recrd Identificatin Data Cnfiguring Device Cmmunicatins Mdbus COM settings fr all f the devices cnnected t the PrtNde Set Mdbus Address fr each f the devices attached t the PrtNde Selecting Stred Cnfiguratins, Setting the Mac Address, Nde_ID, and Baud Rate Selecting Cnfiguratin Files fr Devices: S bank DIP Switches S0 S BACnet MS/TP and BACnet IP DIP Switch Settings LnWrks DIP Switch Settings BACnet MS/TP (FPC-N34): Setting the MAC Address BACnet Netwrks BACnet MS/TP and BACnet/IP (FPC-N34): Setting the Device Instance (Nde-ID) BACnet MS/TP r BACnet/IP: Assigning Specific Device Instances Metasys N2 and Mdbus/TCP (FPC-N34): Setting the Nde-ID BACnet MS/TP (FPC-N34): Setting the Serial Baud Rate (DIP Switch B0 B3) Baud Rate DIP Switch Selectin Interfacing PrtNde t Devices PrtNde FPC-N34 and FPC-N35 Shwing Cnnectin Prts Device Cnnectins t PrtNde Biasing the Mdbus RS-485 Netwrk End f Line Terminatin Jumper fr the Mdbus RS-485 prt n the PrtNde BACnet MS/TP r Metasys N2 (FPC-N34): Wiring Field Prt t RS-485 Netwrk LnWrks (FPC-N35): Wiring Field Prt t LnWrks Netwrk Cnnecting Pwer t PrtNde BACnet/IP and Mdbus TCP: Change the Prtnde IP Address Cnnect the PC t PrtNde via the Ethernet Prt BACnet MS/TP and BACnet/IP: Setting Nde_Offset t Assign Specific Device Instances Accessing the FST Web GUI frm the Web Cnfiguratr BACnet/IP and Mdbus TCP: Setting IP Address fr Field Netwrk LnWrks (FPC-N35): Cmmissining PrtNde n a Lnwrks Netwrk Cmmissining PrtNde FPC-N35 n a LnWrks Netwrk Instructins t Uplad XIF File frm PrtNde FPC-N35 Using FS GUI Web Server CAS BACnet Explrer fr Validating PrtNde in the Field Dwnlading the CAS Explrer and Requesting an Activatin Key CAS BACnet Setup CAS BACnet MS/TP Setup CAS BACnet BACnet/IP Setup Appendix A. Trubleshting Appendix A.1. Check Wiring and Settings Appendix A.2. Take Diagnstic Capture With the FieldServer Utilities Appendix A.3. BACnet/IP: Setting Netwrk_Number fr mre than ne PrtNde n Subnet Appendix A.4. LED Diagnstics fr Mdbus RTU Cmmunicatins Between PrtNde and Devices Appendix B. Additinal Features Appendix B.1. DIP switch settings t supprt 1 thrugh 8 Prestige and Keystne t Metasys N2 and Mdbus TCP Appendix C. Vendr Infrmatin - Triangle Tube Appendix C.1. Prestige Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Appendix C.2. Keystne Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks... 34

6 Triangle Tube s PrtNde Startup Guide Page 6 f 40 Appendix D. A Bank DIP Switch Settings Appendix D.1. A Bank DIP Switch Settings fr MAC Address r Nde-ID Appendix E. Reference Appendix E.1. Specificatins Appendix E.1.1. Cmpliance with UL Regulatins Appendix F. Limited 2 Year Warranty LIST OF FIGURES Figure 1: PrtCessr Part Numbers... 7 Figure 2: Mdbus RTU COM Settings... 8 Figure 3: S Bank DIP Switches... 9 Figure 4: MAC Address DIP Switches Figure 5: Baud Rate DIP Switches Figure 6: Baud Rate Figure 7: PrtNde BACnet FPC-N34 (upper) and PrtNde FPC-N35 (lwer) Figure 8: Pwer and RS-485 Cnnectins Figure 9: Mdbus RS-485 Biasing Switch n the PrtNde N34 (left) and PrtNde N35 (right) Figure 10: Mdbus RS-485 End-Of-Line Terminatin Switch n the PrtNde N34 (left) and Figure 11: Cnnectin frm PrtNde t RS-485 Field Netwrk Figure 12: RS-485 EOL Switch Figure 13: LnWrks Terminal Figure 14: Required current draw fr the PrtNde Figure 15: Pwer Cnnectins Figure 16: Ethernet Prt Lcatin Figure 17: Web Cnfiguratr screen Figure 18: Web Cnfiguratr screen with Active Prfiles Figure 19: Changing IP Address via FST Web GUI Figure 20: LnWrks Service Pin Lcatin Figure 21: Sample f Fserver.XIF File Being Generated Figure 22: Dwnlading the CAS Explrer Figure 23: Requesting CAS Activatin Key Figure 24: Ethernet Prt Lcatin Figure 25: Web Cnfiguratr shwing setting the netwrk number fr BACnet/IP Figure 26: Diagnstic LEDs Figure 27: Specificatins... 39

7 Triangle Tube s PrtNde Startup Guide Page 7 f 40 1 INTRODUCTION 1.1 PrtNde Gateway PrtNde is an external, high perfrmance Building Autmatin multi-prtcl gateway that has been preprgrammed fr Triangle Tube s prducts (hereafter called device ) t varius building autmatin prtcls. These prtcls include BACnet 1 MS/TP, BACnet/IP, Metasys 2 N2 by JCI, Mdbus TCP, and LnWrks 3. Cnfiguratins fr the varius prtcls are stred within the PrtNde and are selectable via DIP switches fr fast and easy installatin. It is nt necessary t dwnlad any cnfiguratin files t supprt the required applicatins. 2 BACNET/LONWORKS SETUP FOR PROTOCESSOR PROTONODE FPC-N34/FPC-N Recrd Identificatin Data Each PrtNde has a unique part number lcated n the underside f the unit. This number shuld be recrded, as it may be required fr technical supprt. The numbers are as fllws: Mdel Part Number PrtNde FPC-N34 FPC-N PrtNde FPC-N35 FPC-N Figure 1: PrtCessr Part Numbers FPC-N34 units have the fllwing 3 prts: RS Ethernet + RS-485. FPC-N35 units have the fllwing 3 prts: LnWrks + Ethernet + RS BACnet is a registered trademark f ASHRAE 2 Metasys is a registered trademark f Jhnsn Cntrls Inc. 4 LnWrks is a registered trademark f Echeln Crpratin

8 Triangle Tube s PrtNde Startup Guide Page 8 f Cnfiguring Device Cmmunicatins Mdbus COM settings fr all f the devices cnnected t the PrtNde The Prestige and Keystne cmmunicate with the PrtNde using the settings listed in Figure 2. These settings are nt adjustable. Serial Prt Setting Device Prtcl Mdbus RTU Baud Rate Parity Nne Data Bits 8 Stp Bits 1 Figure 2: Mdbus RTU COM Settings Set Mdbus Address fr each f the devices attached t the PrtNde Set the Mdbus Address fr each f the devices attached t PrtNde. The Mdbus Address needs t be uniquely assigned, starting with a value f 1 fr the first device. Mdbus Address values fr additinal devices must be sequential (2, 3, 4, ).

9 Triangle Tube s PrtNde Startup Guide Page 9 f Selecting Stred Cnfiguratins, Setting the Mac Address, Nde_ID, and Baud Rate Selecting Cnfiguratin Files fr Devices: S bank DIP Switches S0 S3 The S bank f DIP switches (S0 - S3) are used t select and lad a cnfiguratin file frm a grup f pretested/preladed cnfiguratin files which are stred in the PrtNde FPC-N34 (BACnet MS/TP, BACnet/IP, Mdbus TCP, Metasys N2) and the PrtNde FPC-N35 (LnWrks). S0 S1 S2 S3 S0 S3 DIP Switches Figure 3: S Bank DIP Switches S Bank DIP Switch Lcatin BACnet MS/TP and BACnet IP DIP Switch Settings The fllwing chart describes S0 - S3 DIP Switch cnfiguratin settings fr 1 thrugh 8 device applicatins t supprt BACnet MS/TP and BACnet/IP n a PrtNde FPC-N34 Cver desn t need t be Remved PrtCarrier DIP Switches Prfile - FPC-N S0 S1 S2 S3 1 Prestige t BACnet IP/BACnet MSTP Off Off Off Off 2 Prestige t BACnet IP/BACnet MSTP On Off Off Off 3 Prestige t BACnet IP/BACnet MSTP Off On Off Off 4 Prestige t BACnet IP/BACnet MSTP On On Off Off 5 Prestige t BACnet IP/BACnet MSTP Off Off On Off 6 Prestige t BACnet IP/BACnet MSTP On Off On Off 7 Prestige t BACnet IP/BACnet MSTP Off On On Off 8 Prestige t BACnet IP/BACnet MSTP On On On Off 1 Keystne t BACnet IP/BACnet MSTP Off Off Off On 2 Keystne t BACnet IP/BACnet MSTP On Off Off On 3 Keystne t BACnet IP/BACnet MSTP Off On Off On 4 Keystne t BACnet IP/BACnet MSTP On On Off On 5 Keystne t BACnet IP/BACnet MSTP Off Off On On 6 Keystne t BACnet IP/BACnet MSTP On Off On On 7 Keystne t BACnet IP/BACnet MSTP Off On On On 8 Keystne t BACnet IP/BACnet MSTP On On On On See Appendix B.1 fr the Cnfiguratin DIP switch settings fr - 1 thrugh 8 Prestige and Keystne t Metasys N2 and Mdbus TCP. NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF.

10 Triangle Tube s PrtNde Startup Guide Page 10 f LnWrks DIP Switch Settings The fllwing chart describes the DIP switch settings fr the Prestige and Keystne t supprt LnWrks n a PrtNde FPC-N35. Cver desn t need t be remved PrtCarrier DIP Switches Prfile - FPC-N S0 S1 S2 S3 1 Prestige t Lnwrks Off Off Off Off 2 Prestige t Lnwrks On Off Off Off 3 Prestige t Lnwrks Off On Off Off 4 Prestige t Lnwrks On On Off Off 5 Prestige t Lnwrks Off Off On Off 6 Prestige t Lnwrks On Off On Off 7 Prestige t Lnwrks Off On On Off 8 Prestige t Lnwrks On On On Off 1 Keystne t Lnwrks Off Off Off On 2 Keystne t Lnwrks On Off Off On 3 Keystne t Lnwrks Off On Off On 4 Keystne t Lnwrks On On Off On 5 Keystne t Lnwrks Off Off On On 6 Keystne t Lnwrks On Off On On 7 Keystne t Lnwrks Off On On On 8 Keystne t Lnwrks On On On On NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF BACnet MS/TP (FPC-N34): Setting the MAC Address BACnet Netwrks Only 1 MAC address is set fr PrtNde regardless f hw many devices are cnnected t PrtNde. Set the BACnet MS/TP MAC address f the PrtNde t a value between 1 t 127 (MAC Master Address); this is s that the BMS Frnt End can find the PrtNde via BACnet aut discvery. Nte: Never set a BACnet MS/TP MAC Address frm 128 t 255. Addresses frm 128 t 255 are Slave Addresses and can nt be discvered by BMS Frnt Ends that supprt aut discvery f BACnet MS/TP devices. Set DIP switches A0 A7 t assign MAC Address fr BACnet MS/TP fr the PrtNde FPC-N34. Please refer t Appendix D.1 fr the cmplete range f MAC Addresses and DIP switch settings. Figure 4: MAC Address DIP Switches NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF.

11 Triangle Tube s PrtNde Startup Guide Page 11 f BACnet MS/TP and BACnet/IP (FPC-N34): Setting the Device Instance (Nde-ID) The A Bank f DIP switches are als used t set the BACnet Device Instances. The BACnet Device Instance can range frm 1 t 4,194,303. The BACnet device instances will be calculated by taking the Nde_Offset (default is 50,000) fund in Web Cnfiguratr (Sectin ) and adding it t the value f the A Bank DIP switches (MAC address). When mre than ne device is cnnected t the PrtNde, the subsequent BACnet Device Instance numbers will be sequential frm the first/previus device. Fr example: Given that: Device Instance = Nde_Offset + MAC address Default Nde_Offset value = 50,000 A Bank DIP switch (MAC address) = 11 Then the Device Instance values fr the devices are: Device 1 Instance = 50,011 Device 2 Instance will then be 50,011(Device Instance 1) +1 = 50,012 Device 3 Instance will then be 50,012 (previus Device Instance) +1 = 50, BACnet MS/TP r BACnet/IP: Assigning Specific Device Instances With the default Nde_Offset value f 50,000 the Device Instances values generated will be within the range f 50,000 t 50,127. The values allwed fr a BACnet Device Instance can range frm 1 t 4,194,303. T assign a specific Device Instance (r range), change the Nde_Offset value. Methds fr changing the Nde_Offset value are prvided in Sectin 4.2 This step cannt be perfrmed until after the unit is cnnected and pwered Metasys N2 and Mdbus/TCP (FPC-N34): Setting the Nde-ID Set DIP switches A0 A7 t assign Nde-ID fr Metasys N2 and Mdbus TCP fr the PrtNde FPC- N34. Metasys N2 and Mdbus/TCP Nde-ID Addressing: Metasys N2 and Mdbus/TCP Nde-ID s range frm Please refer t Appendix D.1 fr the full range f addresses fr setting Nde-ID.

12 Triangle Tube s PrtNde Startup Guide Page 12 f BACnet MS/TP (FPC-N34): Setting the Serial Baud Rate (DIP Switch B0 B3) DIP Switches B0 B3 can be used t set the serial baud rate t match the baud rate prvided by the Building Management System fr BACnet MS/TP. DIP Switches B0 B3 are disabled n PrtNde FPC-N35 (FPC-N35 LnWrks). The baud rate n PrtNde fr Metasys N2 is set fr DIP Switches B0 B3 are disabled fr Metasys N2 n PrtNde FPC-N34. B0 B1 B2 B3 Figure 5: Baud Rate DIP Switches NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF Baud Rate DIP Switch Selectin Baud B0 B1 B2 B On On On Off Off Off Off On On On Off On Off Off On On On Off On On Figure 6: Baud Rate

13 Triangle Tube s PrtNde Startup Guide Page 13 f 40 3 INTERFACING PROTONODE TO DEVICES 3.1 PrtNde FPC-N34 and FPC-N35 Shwing Cnnectin Prts Figure 7: PrtNde BACnet FPC-N34 (upper) and PrtNde LnWrks FPC-N35 (lwer)

14 Triangle Tube s PrtNde Startup Guide Page 14 f Device Cnnectins t PrtNde PrtNde 6 Pin Phenix cnnectr fr RS-485 Devices The 6 pin Phenix cnnectr is the same fr PrtNde FPC-N34 (BACnet) and FPC-N35 (LnWrks). Pins 1 thrugh 3 are fr cnnecting t each device. Reference the table in Figure 8 fr Prestige and Keystne wiring terminatins. Multiple devices shuld be daisy chain wired t the PrtNde. Pins 4 thrugh 6 are fr pwer. D nt cnnect pwer (wait until Sectin 3.5). Prestige Keystne PrtNde Pin # Pin assignment Mdbus A (20) MB1 A / MB2 A Pin 1 RS Mdbus B (21) MB1 B / MB2 B Pin 2 RS Mdbus G (22) V- GND Pin 3 RS-485 GND Pwer In (+) Pwer In (+) Pin 4 V + Pwer In (-) Pwer In (-) Pin 5 V - Frame Grund Frame Grund Pin 6 FRAME GND Figure 8: Pwer and RS-485 Cnnectins

15 Triangle Tube s PrtNde Startup Guide Page 15 f Biasing the Mdbus RS-485 Netwrk An RS-485 netwrk with mre than ne device needs t have biasing t ensure prper cmmunicatin. The biasing needs t be dne n ne device. The PrtNde has 530 Ohm resistrs that can be used t set the biasing. The PrtNde s default psitins frm the factry fr the Biasing jumpers are OFF. The OFF psitin is when the 2 RED biasing jumpers straddle the 4 pins clsest t the utside f the bard f the PrtNde. See Figure 9. Only turn biasing ON: IF the BMS cannt see mre than ne device cnnected t the PrtNde AND yu have checked all the settings (Mdbus COM settings, wiring, and DIP switches). T turn biasing ON, mve the 2 RED biasing jumpers t straddle the 4 pins clsest t the inside f the bard f the PrtNde. RS-485 Bias Jumpers Figure 9: Mdbus RS-485 Biasing Jumpers n the PrtNde N34 (left) and PrtNde N35 (right)

16 Triangle Tube s PrtNde Startup Guide Page 16 f End f Line Terminatin Jumper fr the Mdbus RS-485 prt n the PrtNde On lng RS-485 cabling runs, the RS-485 trunk must be prperly terminated at each end. The PrtNde has an End Of Line (EOL) blue jumper. The default setting fr this Blue EOL switch is OFF with the jumper straddling the pins clsest t the inside f the bard f the PrtNde. On shrt cabling runs the EOL jumper des nt t need t be turned ON. If the PrtNde is placed at ne f the ends f the trunk, set the blue EOL jumper t the ON psitin straddling the pins clsest t the utside f the bard f the PrtNde. Always leave the single Red Jumper in the A psitin (default factry setting). Mdbus RS-485 EOL Jumper Leave in A Psitin Figure 10: Mdbus RS-485 End-Of-Line Terminatin Jumper n the PrtNde N34 (left) and PrtNde N35 (right)

17 Triangle Tube s PrtNde Startup Guide Page 17 f BACnet MS/TP r Metasys N2 (FPC-N34): Wiring Field Prt t RS-485 Netwrk Cnnect the BACnet MS/TP r Metasys N2 RS-485 netwrk wires t the 3-pin RS-485 cnnectr n PrtNde FPC-N34 as shwn belw in Figure 11. See Sectin 4 fr infrmatin n cnnecting t BACnet/IP netwrk. If the PrtNde is the last device n the BACnet MS/TP r Metasys N2 trunk, then the End-Of- Line Terminatin Switch needs t be enabled (Figure 12). It is disabled by default. BMS RS-485 Wiring PrtNde Pin # Pin Assignment RS Pin 1 RS RS Pin 2 RS Pin 3 RS-485 GND + - G Figure 11: Cnnectin frm PrtNde t RS-485 Field Netwrk End-f-Line Switch Figure 12: RS-485 EOL Switch 3.4 LnWrks (FPC-N35): Wiring Field Prt t LnWrks Netwrk Cnnect PrtNde t the field netwrk with the LnWrks terminal using a twisted pair nn-shielded cable. LnWrks has n plarity. Figure 13: LnWrks Terminal

18 Triangle Tube s PrtNde Startup Guide Page 18 f Cnnecting Pwer t PrtNde Apply pwer t PrtNde as shw belw in Figure 14. Ensure that the pwer supply used cmplies with the specificatins prvided in Appendix E.1. PrtNde accepts either 9-30VDC r VAC n pins 4 and 5. Pwer Requirement fr PrtNde at 9V thrugh 30 VDC r VAC Current Draw Type PrtNde Family 12VDC/VAC 24VDC/VAC 30VDC FPC N34 (Typical) 170mA 100mA 80mA FPC N34 (Maximum) 240mA 140mA 100mA FPC N35 (Typical) 210mA 100mA 90mA FPC N35 (Maximum) 250mA 130mA 100mA Nte: These values are nminal and a safety margin shuld be added t the pwer supply f the hst system. A safety margin f 25% is recmmended. Figure 14: Required current draw fr the PrtNde Pwer t PrtNde PrtNde Pin # Pin Assignment Pwer In (+) Pin 4 V + Pwer In (-) Pin 5 V - Frame Grund Pin 6 FRAME GND Figure 15: Pwer Cnnectins

19 Triangle Tube s PrtNde Startup Guide Page 19 f 40 4 BACNET/IP AND MODBUS TCP: CHANGE THE PROTONODE IP ADDRESS 4.1 Cnnect the PC t PrtNde via the Ethernet Prt Ethernet Figure 16: Ethernet Prt Lcatin Cnnect a standard CAT5 Ethernet cable (Straight thrugh r Crss-Over) between the PC and PrtNde The Default IP Address f PrtNde is , Subnet Mask is If the PC and PrtNde are n different IP Netwrks, assign a static IP Address t the PC n the xxx netwrk Fr Windws XP: G t > > Right-click n Lcal Area Cnnectin > Prperties Highlight > Fr Windws 7: G t > > > > Right-click n Lcal Area Cnnectin > Prperties Highlight > Fr Windws XP and Windws 7, select: Use the fllwing IP address Click twice

20 Triangle Tube s PrtNde Startup Guide Page 20 f BACnet MS/TP and BACnet/IP: Setting Nde_Offset t Assign Specific Device Instances After setting yur PC t be n the same subnet as the PrtNde (Sectin 4.1), pen a web brwser n yur PC and enter the IP address f the PrtNde; the default address is If the IP address f the PrtNde has been changed by previus cnfiguratin, yu will need t get the assigned IP address frm the netwrk administratr. The Web Cnfiguratr will be displayed as yur landing page. (Figure 17) Nde_Offset field will be presented displaying the current value (default = 50,000). Change the value f Nde_Offset t establish the desired Device Instance values, and click SUBMIT. Given that: Device Instance = Nde_Offset + MAC address Then: Nde_Offset (required) = Device Instance (desired) MAC address Fr example: Device 1 has a Mdbus Address f 1 Device 2 has a Mdbus Address f 2 Device 3 has a Mdbus Address f 3 MAC address (Bank A DIP switches) = 11 Desired Device Instance fr 1 st device = 1,011 Nde_Offset (required) = 1,011 (MAC address) = 1, = 1,000 The Nde_Offset value will be applied t all devices. Device 1 Instance will then be = 1,000 + MAC address = 1, = 1,011 Device 2 Instance will then be = Previus Value + 1 = 1, = 1,012 Device 3 Instance will then be = Previus Value + 1 = 1, = 1,013 Figure 17: Web Cnfiguratr screen

21 Triangle Tube s PrtNde Startup Guide Page 21 f Accessing the FST Web GUI frm the Web Cnfiguratr After setting yur PC t be n the same subnet as the PrtNde (Sectin 4.1), pen a web brwser n yur PC and enter the IP address f the PrtNde; the default address is If the IP address f the PrtNde has been changed by previus cnfiguratin, yu will need t get the assigned IP address frm the netwrk administratr. The Web Cnfiguratr will be displayed as yur landing page. (Figure 18) Belw the Active Prfiles heading yu shuld see prfiles listed fr cnnected devices. If n prfiles are present, then the wiring, baud rate, and DIP switch settings must be checked, because there is a prblem with device cmmunicatins. All the active prfiles must shw the crrect Nde-ID s befre prceeding. T access the FST Web GUI, click n the Diagnstics & Debugging buttn in the bttm right side f the page. Figure 18: Web Cnfiguratr screen with Active Prfiles

22 Triangle Tube s PrtNde Startup Guide Page 22 f BACnet/IP and Mdbus TCP: Setting IP Address fr Field Netwrk Frm the Web Cnfiguratr landing page (Figure 18), click n the Diagnstics & Debugging buttn in the bttm right side f the page t access the FST Web GUI. The FST Web GUI page will be presented. Frm the FST Web GUI s landing page, click n Setup t expand the navigatin tree and then select Netwrk Settings t access the IP Settings menu. (Figure 19) Figure 19: Changing IP Address via FST Web GUI Enter the new IP address fr the PrtNde s Ethernet prt in the N1 IP address field. If necessary, change the Subnet Mask setting in the N1 Netmask field. If necessary, change the IP Gateway setting in the Default Gateway field. Nte: If the PrtNde is cnnected t a ruter, the IP Gateway f the PrtNde shuld be set t the IP address f the ruter that it is cnnected t. Click the System Restart buttn at the bttm f the page t apply changes and restart the PrtNde. Unplug Ethernet cable frm PC and cnnect the PrtNde t the netwrk hub r ruter. Recrd the IP address assigned t the PrtNde fr future reference.

23 Triangle Tube s PrtNde Startup Guide Page 23 f 40 5 LONWORKS (FPC-N35): COMMISSIONING PROTONODE ON A LONWORKS NETWORK Cmmissining may nly be perfrmed by the LnWrks administratr. 5.1 Cmmissining PrtNde FPC-N35 n a LnWrks Netwrk The User will be prmpted by the LnWrks Administratr t hit the Service Pin n the PrtNde FPC-N35 at the crrect step f the Cmmissining prcess which is different fr each LnWrks Netwrk Management Tl. If an XIF file is required, see steps in Sectin t generate XIF Figure 20: LnWrks Service Pin Lcatin Instructins t Uplad XIF File frm PrtNde FPC-N35 Using FS GUI Web Server Cnnect a standard CAT5 Ethernet cable (Straight thrugh r Crss-Over) between the PC and PrtNde The Default IP Address f PrtNde is , Subnet Mask is If the PC and PrtNde are n different IP Netwrks, assign a static IP Address t the PC n the xxx netwrk Fr Windws XP: G t > > Right-click n Lcal Area Cnnectin > Prperties Highlight > Fr Windws 7: G t > > > > Right-click n Lcal Area Cnnectin > Prperties Highlight >

24 Triangle Tube s PrtNde Startup Guide Page 24 f 40 Fr Windws XP and Windws 7, select: Use the fllwing IP address Click twice Open a web brwser and g t the fllwing address: IP address f PrtCessr/fserver.xif Example: /fserver.xif If the web brwser prmpts yu t save file, save the file nt the PC. If the web brwser displays the xif file as a web page, save the file n yur PC as fserver.xif Figure 21: Sample f Fserver.XIF File Being Generated

25 Triangle Tube s PrtNde Startup Guide Page 25 f 40 6 CAS BACNET EXPLORER FOR VALIDATING PROTONODE IN THE FIELD PrtCessr has arranged a cmplementary 2 week fully functinal cpy f CAS BACnet Explrer (thrugh Chipkin Autmatin) that can be used t validate BACnet MS/TP and/r BACnet/IP cmmunicatins f PrtNde in the field withut having t have the BMS Integratr n site. A Serial r USB t RS-485 cnverter is needed t test BACnet MS/TP. 6.1 Dwnlading the CAS Explrer and Requesting an Activatin Key T request the cmplementary BACnet CAS key, g t and fill in all the infrmatin. Enter Vendr Cde TriangleTube2BACnet. Once cmpleted, the key will be sent t the address that was submitted. Frm this , the lng key will need t be cpied and pasted int the CAS key activatin page. Figure 22: Dwnlading the CAS Explrer G t the fllwing web site, dwnlad and install the CAS BACnet Explrer t yur PC: In the CAS Activatin frm, enter the address and paste the CAS key that was sent. Once cmpleted, select Activatin. Figure 23: Requesting CAS Activatin Key

26 Triangle Tube s PrtNde Startup Guide Page 26 f CAS BACnet Setup These are the instructins t set CAS Explrer up fr the first time n BACnet MS/TP and BACnet/IP CAS BACnet MS/TP Setup Using the Serial r USB t RS-485 cnverter, cnnect it t yur PC and the 3 Pin BACnet MS/TP cnnectr n PrtNde FPC-N34. In CAS Explrer, d the fllwing: Click n settings Check the BACnet MSTP bx and uncheck the BACnet/IP and BACnet Ethernet bxes Set the BACnet MSTP MAC address t 0 Set the BACnet MSTP Baud Rate t Click Ok On the bttm right-hand crner, make sure that the BACnet MSTP bx is green Click n discver Check all 4 bxes Click Send CAS BACnet BACnet/IP Setup See Sectin 4.1 t set the IP address and subnet f the PC that will be running the CAS Explrer. Cnnect a standard CAT5 Ethernet cable (Straight thrugh r Crss-Over) between the PC and PrtNde In CAS Explrer, d the fllwing: Click n settings Check the BACnet/IP bx and uncheck the BACnet MSTP and BACnet Ethernet bxes In the Select a Netwrk Device bx, select the netwrk card f the PC by clicking n it Click Ok On the bttm right-hand crner, make sure that the BACnet/IP bx is green Click n discver Check all 4 bxes Click Send

27 Triangle Tube s PrtNde Startup Guide Page 27 f 40 Appendix A. Trubleshting Appendix A.1. Check Wiring and Settings N COMS n Mdbus RTU side. If Tx/Rx are nt flashing rapidly then there is a COM issue n the Mdbus side and yu need t check the fllwing things: Visual bservatins f LEDs n PrtNde. (Appendix A.4) Check Mdbus device address Verify wiring Verify all the Mdbus RTU devices were discvered in FST Web Cnfiguratr. (Sectin 4.2) Field COM prblems: Visual bservatins f LEDs n PrtNde. (Appendix A.4) Visual dipswitch settings (using crrect baud rate and device instance) Verify IP address setting Verify wiring If the prblem still exists, a Diagnstic Capture needs t be taken and sent t FieldServer. (Appendix A.2)

28 Triangle Tube s PrtNde Startup Guide Page 28 f 40 Appendix A.2. Take Diagnstic Capture With the FieldServer Utilities Once the Diagnstic Capture lg is cmplete, it t supprt@prtcessr.cm. The Diagnstic Capture will allw us t rapidly diagnse the prblem. Make sure the FieldServer-Tlbx utilities are laded n the PC Ethernet Prt Figure 24: Ethernet Prt Lcatin Disable any wireless Ethernet adapters n the PC/Laptp Disable firewall and virus prtectin sftware if pssible Cnnect a standard CAT5 Ethernet cable (Straight thrugh r Crss-Over) between the PC and PrtNde The Default IP Address f PrtNde is , Subnet Mask is If the PC and PrtNde are n different IP Netwrks, assign a static IP Address t the PC n the xxx netwrk Fr Windws XP: G t > > Right-click n Lcal Area Cnnectin > Prperties Highlight > Fr Windws 7: G t > > > > Right-click n Lcal Area Cnnectin > Prperties Highlight >

29 Triangle Tube s PrtNde Startup Guide Page 29 f 40 Fr Windws XP and Windws 7, select: Use the fllwing IP address Click twice Duble click n the FST Diag Utility Step 1: Select a Field Server IP Address The IP address can be entered manually r selected by clicking n buttn 1 using the Utility Type in the PrtNde IP address Default IP Address is Press here t retrieve the IP address. Lcate where the lg is saved n the PC Select a lg type. Press the Take Lg buttn. Step 2: Take a Lg Press the Take Lg buttn. While the Utility runs a few DOS prmpts will flash acrss the mnitr. Dn't click r type anything in t these DOS prmpts. This step may take a few minutes depending n the chsen Lg Type and cmputer speed. When the Utility is finished yu will be presented with a lg f events that have ccurred.

30 Triangle Tube s PrtNde Startup Guide Page 30 f 40 Step 3: Send Lg Click the Send Lg buttn lcated near the bttm f the dialg. The fllwing dialg shuld appear Push the Lcate Flder buttn t launch explrer and have it pint directly at the crrect flder. The file uplad.zip must be sent t supprt@fieldserver.cm Step 4: Clse the Prgram Press the exit buttn when the lg is cmpleted

31 Triangle Tube s PrtNde Startup Guide Page 31 f 40 Appendix A.3. BACnet/IP: Setting Netwrk_Number fr mre than ne PrtNde n Subnet On the main Web Cnfiguratr screen, update the Netwrk Number in the Netwrk_Nr and hit Submit. Please nte that the default value is 50. Figure 25: Web Cnfiguratr shwing setting the netwrk number fr BACnet/IP Appendix A.4. LED Diagnstics fr Mdbus RTU Cmmunicatins Between PrtNde and Devices Please see the diagram belw fr PrtNde FPC-N34 and FPC-N35 LED Lcatins. SPL Diagnstic LEDs Tag SPL RUN ERR RX TX PWR Descriptin The SPL LED will light if the PrtNde is ff line. The RUN LED will start flashing 20 secnds after pwer indicating nrmal peratin. The SYS ERR LED will g n slid 15 secnds after pwer up. It will turn ff after 5 secnds. A steady red light will indicate there is a system errr n PrtNde. If this ccurs, immediately reprt the related system errr shwn in the errr screen f the GUI interface t FieldServer Technlgies fr evaluatin. The RX LED will flash when a message is received frm the biler. The TX LED will flash when a message is sent t the biler. This is the pwer light and shuld shw steady green at all times when PrtNde is pwered. Figure 26: Diagnstic LEDs

32 Triangle Tube s PrtNde Startup Guide Page 32 f 40 Appendix B. Additinal Features Appendix B.1. DIP switch settings t supprt 1 thrugh 8 Prestige and Keystne t Metasys N2 and Mdbus TCP Nte: The lid n tp f the PrtNde has t be remved in rder t select the A Bank f DIP switches. Pull n the lid while hlding n t the 6 pin Phenix cnnectr. Please d nt hld the wall munt tabs as these are designed t break ff if nt required! T select these cnfiguratins, pen the PrtNde and set the A bank f switches (A1 r A2 r A3) n the small PrtCessr mdule that sits n tp f the PrtCarrier (inside the PrtNde). PrtCessr A1 DIP switch starts n the bttm f the A bank f DIP switches belw. PrtCessr A3-A8 DIP switches are disabled. S Bank DIP Switches A1, A2, and A3 DIP Switches N2 and Mdbus TCP PrtCarrier DIP Switches PrtCessr DIP Switches (Remve Cver) Prfile - FPC-N S0 S1 S2 S3 A1 A2 A3 A4 A5 A6 A7 A8 1 Prestige t Metasys N2 Off Off Off Off On Off Off Off Off Off Off Off 2 Prestige t Metasys N2 On Off Off Off On Off Off Off Off Off Off Off 3 Prestige t Metasys N2 Off On Off Off On Off Off Off Off Off Off Off 4 Prestige t Metasys N2 On On Off Off On Off Off Off Off Off Off Off 5 Prestige t Metasys N2 Off Off On Off On Off Off Off Off Off Off Off 6 Prestige t Metasys N2 On Off On Off On Off Off Off Off Off Off Off 7 Prestige t Metasys N2 Off On On Off On Off Off Off Off Off Off Off 8 Prestige t Metasys N2 On On On Off On Off Off Off Off Off Off Off 1 Keystne t Metasys N2 Off Off Off On On Off Off Off Off Off Off Off 2 Keystne t Metasys N2 On Off Off On On Off Off Off Off Off Off Off 3 Keystne t Metasys N2 Off On Off On On Off Off Off Off Off Off Off 4 Keystne t Metasys N2 On On Off On On Off Off Off Off Off Off Off 5 Keystne t Metasys N2 Off Off On On On Off Off Off Off Off Off Off 6 Keystne t Metasys N2 On Off On On On Off Off Off Off Off Off Off 7 Keystne t Metasys N2 Off On On On On Off Off Off Off Off Off Off 8 Keystne t Metasys N2 On On On On On Off Off Off Off Off Off Off Mdbus TCP fr all Off Off Off Off Off On Off Off Off Off Off Off

33 Triangle Tube s PrtNde Startup Guide Page 33 f 40 Appendix C. Vendr Infrmatin - Triangle Tube Appendix C.1. Prestige Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet Object Type BACnet Object ID N2 Data Type N2 Pint Address Ln Name Ln SNVT CH Demand AV 1 AO 1 nvi/nvchdemand SNVT_cunt_inc_f Maximum Firing Rate AV 2 AO 2 nvi/nvmaxfirrate SNVT_lev_percent CH Setpint AV 3 AO 3 nvi/nvch1sp SNVT_temp_p CH1 Max Setpint AI 4 AI 4 nvch1maxsp SNVT_temp_p DHW Strage Setpint AI 5 AI 5 nvdhwstragesp SNVT_temp_p PC Manual Mde BI 6 DI 6 nvpcmanualmde SNVT_switch DHW Mde BI 7 DI 7 nvdhwmde SNVT_switch CH Mde BI 8 DI 8 nvchmde SNVT_switch Freeze Prtectin Mde BI 9 DI 9 nvfrzprtctmd SNVT_switch Flame Present BI 10 DI 10 nvflamepresent SNVT_switch CH(1) Pump BI 11 DI 11 nvchpmp SNVT_switch DHW Pump BI 12 DI 12 nvdhwpmp SNVT_switch System / CH2 Pump BI 13 DI 13 nvsysch2pmp SNVT_switch Lckut Cde Type AI 14 AI 14 nvlcktcdtype SNVT_cunt_inc_f Lckut Cde AI 15 AI 15 nvlcktcd SNVT_cunt_inc_f Lckut Status AI 16 AI 16 nvlcktstatus SNVT_cunt_inc_f Biler Supply Temp / Sys AI 17 AI 17 nvblrsuptmp SNVT_temp_p Temp Biler Return Temp AI 18 AI 18 nvblrrettmp SNVT_temp_p DHW Strage Temp AI 19 AI 19 nvdhwstrgtmp SNVT_temp_p Biler Flue Temp AI 20 AI 20 nvblrfluetmp SNVT_temp_p Outdr Temp AI 21 AI 21 nvoutdrtmp SNVT_temp_p Flame Inizatin Current AI 22 AI 22 nvflmincrrt SNVT_cunt_inc_f Biler / Cascade Firing AI 23 AI 23 nvblrcscfirrat SNVT_lev_percent Rate Biler Setpint AI 24 AI 24 nvblrsp SNVT_temp_p Nte: See Mdbus Interface in the Prestige Cntrl Applicatin Supplement TriMax fr additinal infrmatin.

34 Triangle Tube s PrtNde Startup Guide Page 34 f 40 Appendix C.2. Keystne Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet Object Type BACnet Object ID N2 Data Type N2 Pint Address Ln Name Ln SNVT Demand surce AI 1 AI 1 nvxdemsrc SNVT_cunt_inc_f Outlet sensr AI 2 AI 2 nvxoutletsen SNVT_temp_p Firing rate AI 3 AI 3 nvxfiringrate SNVT_cunt_inc_f Fan speed AI 4 AI 4 nvxfanspeed SNVT_cunt_inc_f Flame signal AI 5 AI 5 nvxflamesignal SNVT_cunt_inc_f Inlet sensr AI 6 AI 6 nvxinletsen SNVT_temp_p DHW sensr AI 7 AI 7 nvxdhwsen SNVT_temp_p Stack sensr AI 8 AI 8 nvxstacksen SNVT_temp_p Active CH setpint AI 9 AI 9 nvxactchsp SNVT_temp_p Active DHW setpint AI 10 AI 10 nvxactdhwsp SNVT_temp_p Active LL setpint AI 11 AI 11 nvxactllsp SNVT_temp_p Analg mdulatin input AI 12 AI 12 nvxanamdin SNVT_cunt_inc_f Burner cntrl status AI 13 AI 13 nvxbrnctrlstat SNVT_cunt_inc_f Lckut cde AI 14 AI 14 nvxlckutcde SNVT_cunt_inc_f Alarm reasn AI 15 AI 15 nvxalarmreasn SNVT_cunt_inc_f Hld cde AI 16 AI 16 nvxhldcde SNVT_cunt_inc_f CH status AI 17 AI 17 nvxchstatus SNVT_cunt_inc_f CH setpint surce AI 18 AI 18 nvxch_sp_src SNVT_cunt_inc_f CH heat demand AI 19 AI 19 nvxch_heatdem SNVT_cunt_inc_f CH burner demand AI 20 AI 20 nvxch_brndem SNVT_cunt_inc_f DHW status AI 21 AI 21 nvxdhwstatus SNVT_cunt_inc_f DHW Pririty Cunt AI 22 AI 22 nvxdhwpricunt SNVT_cunt_inc_f DHW heat demand AI 23 AI 23 nvxdhwheatdem SNVT_cunt_inc_f DHW burner demand AI 24 AI 24 nvxdhwbrndem SNVT_cunt_inc_f DHW pump status AI 25 AI 25 nvxdhwpmpstatus SNVT_cunt_inc_f DHW Pump Idle Days AI 26 AI 26 nvxdhwpmpidlday SNVT_cunt_inc_f Cunt System pump status AI 27 AI 27 nvxsyspmpstat SNVT_cunt_inc_f System Pump Idle Days AI 28 AI 28 nvxsyspmpidlday SNVT_cunt_inc_f Cunt Biler pump status AI 29 AI 29 nvxblrpmpstat SNVT_cunt_inc_f Biler Pump Idle Days AI 30 AI 30 nvxblrpmpidlday SNVT_cunt_inc_f Cunt Burner run time AV 31 AO 31 nvi/nvxbrnruntime SNVT_cunt_inc_f Lead lag master status AI 32 AI 32 nvxllmstrstat SNVT_cunt_inc_f Lead lag slave status AI 33 AI 33 nvxllslvstat SNVT_cunt_inc_f Lead Lag Master AI 34 AI 34 nvxllmstrspsrc SNVT_cunt_inc_f Setpint Surce Outdr temperature AI 35 AI 35 nvxoutdrtmp SNVT_temp_p System Sensr AI 36 AI 36 nvxsyssen SNVT_temp_p CH setpint AV 37 AO 37 nvi/nvxch_sp SNVT_temp_p Lead Lag setpint AV 38 AO 38 nvi/nvxll_sp SNVT_temp_p Warm weather AV 39 AO 39 nvi/nvxwrmwthrsh SNVT_temp_p shutdwn setpint tsp Lead Lag active service AI 40 AI 40 nvxllactsrvice SNVT_cunt_inc_f Slave 1 State AI 41 AI 41 nvxslv1state SNVT_cunt_inc_f Slave 1 firing rate AI 42 AI 42 nvxslv1firrate SNVT_cunt_inc_f

35 Triangle Tube s PrtNde Startup Guide Page 35 f 40 Slave 2 State AI 43 AI 43 nvxslv2state SNVT_cunt_inc_f Slave 2 firing rate AI 44 AI 44 nvxslv2firrate SNVT_cunt_inc_f Slave 3 State AI 45 AI 45 nvxslv3state SNVT_cunt_inc_f Slave 3 firing rate AI 46 AI 46 nvxslv3firrate SNVT_cunt_inc_f Slave 4 State AI 47 AI 47 nvxslv4state SNVT_cunt_inc_f Slave 4 firing rate AI 48 AI 48 nvxslv4firrate SNVT_cunt_inc_f Slave 5 State AI 49 AI 49 nvxslv5state SNVT_cunt_inc_f Slave 5 firing rate AI 50 AI 50 nvxslv5firrate SNVT_cunt_inc_f Slave 6 State AI 51 AI 51 nvxslv6state SNVT_cunt_inc_f Slave 6 firing rate AI 52 AI 52 nvxslv6firrate SNVT_cunt_inc_f Slave 7 State AI 53 AI 53 nvxslv7state SNVT_cunt_inc_f Slave 7 firing rate AI 54 AI 54 nvxslv7firrate SNVT_cunt_inc_f Slave 8 State AI 55 AI 55 nvxslv8state SNVT_cunt_inc_f Slave 8 firing rate AI 56 AI 56 nvxslv8firrate SNVT_cunt_inc_f Master firing rate AI 57 AI 57 nvxmstrfirrate SNVT_cunt_inc_f CH Enable BV 58 DO 58 nvi/nv1chenable SNVT_cunt_inc_f Lead Lag Op Switch BV 59 DO 59 nvi/nv1ll_opswitch SNVT_cunt_inc_f Nte: See Hneywell Sftware Interface Specificatin Sla Mdbus Interface (# ) fr additinal infrmatin.

36 Triangle Tube s PrtNde Startup Guide Page 36 f 40 Appendix D. A Bank DIP Switch Settings Appendix D.1. A Bank DIP Switch Settings fr MAC Address r Nde-ID Address A0 A1 A2 A3 A4 A5 A6 A7 0 Off Off Off Off Off Off Off Off 1 On Off Off Off Off Off Off Off 2 Off On Off Off Off Off Off Off 3 On On Off Off Off Off Off Off 4 Off Off On Off Off Off Off Off 5 On Off On Off Off Off Off Off 6 Off On On Off Off Off Off Off 7 On On On Off Off Off Off Off 8 Off Off Off On Off Off Off Off 9 On Off Off On Off Off Off Off 10 Off On Off On Off Off Off Off 11 On On Off On Off Off Off Off 12 Off Off On On Off Off Off Off 13 On Off On On Off Off Off Off 14 Off On On On Off Off Off Off 15 On On On On Off Off Off Off 16 Off Off Off Off On Off Off Off 17 On Off Off Off On Off Off Off 18 Off On Off Off On Off Off Off 19 On On Off Off On Off Off Off 20 Off Off On Off On Off Off Off 21 On Off On Off On Off Off Off 22 Off On On Off On Off Off Off 23 On On On Off On Off Off Off 24 Off Off Off On On Off Off Off 25 On Off Off On On Off Off Off 26 Off On Off On On Off Off Off 27 On On Off On On Off Off Off 28 Off Off On On On Off Off Off 29 On Off On On On Off Off Off 30 Off On On On On Off Off Off 31 On On On On On Off Off Off 32 Off Off Off Off Off On Off Off 33 On Off Off Off Off On Off Off 34 Off On Off Off Off On Off Off 35 On On Off Off Off On Off Off 36 Off Off On Off Off On Off Off 37 On Off On Off Off On Off Off 38 Off On On Off Off On Off Off 39 On On On Off Off On Off Off 40 Off Off Off On Off On Off Off 41 On Off Off On Off On Off Off 42 Off On Off On Off On Off Off 43 On On Off On Off On Off Off 44 Off Off On On Off On Off Off 45 On Off On On Off On Off Off 46 Off On On On Off On Off Off Address A0 A1 A2 A3 A4 A5 A6 A7 47 On On On On Off On Off Off 48 Off Off Off Off On On Off Off 49 On Off Off Off On On Off Off 50 Off On Off Off On On Off Off 51 On On Off Off On On Off Off 52 Off Off On Off On On Off Off 53 On Off On Off On On Off Off 54 Off On On Off On On Off Off 55 On On On Off On On Off Off 56 Off Off Off On On On Off Off 57 On Off Off On On On Off Off 58 Off On Off On On On Off Off 59 On On Off On On On Off Off 60 Off Off On On On On Off Off 61 On Off On On On On Off Off 62 Off On On On On On Off Off 63 On On On On On On Off Off 64 Off Off Off Off Off Off On Off 65 On Off Off Off Off Off On Off 66 Off On Off Off Off Off On Off 67 On On Off Off Off Off On Off 68 Off Off On Off Off Off On Off 69 On Off On Off Off Off On Off 70 Off On On Off Off Off On Off 71 On On On Off Off Off On Off 72 Off Off Off On Off Off On Off 73 On Off Off On Off Off On Off 74 Off On Off On Off Off On Off 75 On On Off On Off Off On Off 76 Off Off On On Off Off On Off 77 On Off On On Off Off On Off 78 Off On On On Off Off On Off 79 On On On On Off Off On Off 80 Off Off Off Off On Off On Off 81 On Off Off Off On Off On Off 82 Off On Off Off On Off On Off 83 On On Off Off On Off On Off 84 Off Off On Off On Off On Off 85 On Off On Off On Off On Off 86 Off On On Off On Off On Off 87 On On On Off On Off On Off 88 Off Off Off On On Off On Off 89 On Off Off On On Off On Off 90 Off On Off On On Off On Off 91 On On Off On On Off On Off 92 Off Off On On On Off On Off 93 On Off On On On Off On Off

37 Triangle Tube s PrtNde Startup Guide Page 37 f 40 Address A0 A1 A2 A3 A4 A5 A6 A7 94 Off On On On On Off On Off 95 On On On On On Off On Off 96 Off Off Off Off Off On On Off 97 On Off Off Off Off On On Off 98 Off On Off Off Off On On Off 99 On On Off Off Off On On Off 100 Off Off On Off Off On On Off 101 On Off On Off Off On On Off 102 Off On On Off Off On On Off 103 On On On Off Off On On Off 104 Off Off Off On Off On On Off 105 On Off Off On Off On On Off 106 Off On Off On Off On On Off 107 On On Off On Off On On Off 108 Off Off On On Off On On Off 109 On Off On On Off On On Off 110 Off On On On Off On On Off 111 On On On On Off On On Off 112 Off Off Off Off On On On Off 113 On Off Off Off On On On Off 114 Off On Off Off On On On Off 115 On On Off Off On On On Off 116 Off Off On Off On On On Off 117 On Off On Off On On On Off 118 Off On On Off On On On Off 119 On On On Off On On On Off 120 Off Off Off On On On On Off 121 On Off Off On On On On Off 122 Off On Off On On On On Off 123 On On Off On On On On Off 124 Off Off On On On On On Off 125 On Off On On On On On Off 126 Off On On On On On On Off 127 On On On On On On On Off 128 Off Off Off Off Off Off Off On 129 On Off Off Off Off Off Off On 130 Off On Off Off Off Off Off On 131 On On Off Off Off Off Off On 132 Off Off On Off Off Off Off On 133 On Off On Off Off Off Off On 134 Off On On Off Off Off Off On 135 On On On Off Off Off Off On 136 Off Off Off On Off Off Off On 137 On Off Off On Off Off Off On 138 Off On Off On Off Off Off On 139 On On Off On Off Off Off On 140 Off Off On On Off Off Off On 141 On Off On On Off Off Off On 142 Off On On On Off Off Off On Address A0 A1 A2 A3 A4 A5 A6 A7 143 On On On On Off Off Off On 144 Off Off Off Off On Off Off On 145 On Off Off Off On Off Off On 146 Off On Off Off On Off Off On 147 On On Off Off On Off Off On 148 Off Off On Off On Off Off On 149 On Off On Off On Off Off On 150 Off On On Off On Off Off On 151 On On On Off On Off Off On 152 Off Off Off On On Off Off On 153 On Off Off On On Off Off On 154 Off On Off On On Off Off On 155 On On Off On On Off Off On 156 Off Off On On On Off Off On 157 On Off On On On Off Off On 158 Off On On On On Off Off On 159 On On On On On Off Off On 160 Off Off Off Off Off On Off On 161 On Off Off Off Off On Off On 162 Off On Off Off Off On Off On 163 On On Off Off Off On Off On 164 Off Off On Off Off On Off On 165 On Off On Off Off On Off On 166 Off On On Off Off On Off On 167 On On On Off Off On Off On 168 Off Off Off On Off On Off On 169 On Off Off On Off On Off On 170 Off On Off On Off On Off On 171 On On Off On Off On Off On 172 Off Off On On Off On Off On 173 On Off On On Off On Off On 174 Off On On On Off On Off On 175 On On On On Off On Off On 176 Off Off Off Off On On Off On 177 On Off Off Off On On Off On 178 Off On Off Off On On Off On 179 On On Off Off On On Off On 180 Off Off On Off On On Off On 181 On Off On Off On On Off On 182 Off On On Off On On Off On 183 On On On Off On On Off On 184 Off Off Off On On On Off On 185 On Off Off On On On Off On 186 Off On Off On On On Off On 187 On On Off On On On Off On 188 Off Off On On On On Off On 189 On Off On On On On Off On 190 Off On On On On On Off On 191 On On On On On On Off On

38 Triangle Tube s PrtNde Startup Guide Page 38 f 40 Address A0 A1 A2 A3 A4 A5 A6 A7 192 Off Off Off Off Off Off On On 193 On Off Off Off Off Off On On 194 Off On Off Off Off Off On On 195 On On Off Off Off Off On On 196 Off Off On Off Off Off On On 197 On Off On Off Off Off On On 198 Off On On Off Off Off On On 199 On On On Off Off Off On On 200 Off Off Off On Off Off On On 201 On Off Off On Off Off On On 202 Off On Off On Off Off On On 203 On On Off On Off Off On On 204 Off Off On On Off Off On On 205 On Off On On Off Off On On 206 Off On On On Off Off On On 207 On On On On Off Off On On 208 Off Off Off Off On Off On On 209 On Off Off Off On Off On On 210 Off On Off Off On Off On On 211 On On Off Off On Off On On 212 Off Off On Off On Off On On 213 On Off On Off On Off On On 214 Off On On Off On Off On On 215 On On On Off On Off On On 216 Off Off Off On On Off On On 217 On Off Off On On Off On On 218 Off On Off On On Off On On 219 On On Off On On Off On On 220 Off Off On On On Off On On 221 On Off On On On Off On On 222 Off On On On On Off On On 223 On On On On On Off On On 224 Off Off Off Off Off On On On 225 On Off Off Off Off On On On 226 Off On Off Off Off On On On 227 On On Off Off Off On On On 228 Off Off On Off Off On On On 229 On Off On Off Off On On On 230 Off On On Off Off On On On 231 On On On Off Off On On On 232 Off Off Off On Off On On On 233 On Off Off On Off On On On 234 Off On Off On Off On On On 235 On On Off On Off On On On 236 Off Off On On Off On On On 237 On Off On On Off On On On 238 Off On On On Off On On On 239 On On On On Off On On On 240 Off Off Off Off On On On On Address A0 A1 A2 A3 A4 A5 A6 A7 241 On Off Off Off On On On On 242 Off On Off Off On On On On 243 On On Off Off On On On On 244 Off Off On Off On On On On 245 On Off On Off On On On On 246 Off On On Off On On On On 247 On On On Off On On On On 248 Off Off Off On On On On On 249 On Off Off On On On On On 250 Off On Off On On On On On 251 On On Off On On On On On 252 Off Off On On On On On On 253 On Off On On On On On On 254 Off On On On On On On On 255 On On On On On On On On

39 Triangle Tube s PrtNde Startup Guide Page 39 f 40 Appendix E. Reference Appendix E.1. Specificatins Electrical Cnnectins Apprvals: Pwer Requirements Physical Dimensins Weight: Operating Temperature: Surge Suppressin Humidity: PrtNde FPC-N34 One 6-pin Phenix cnnectr, ne RS-485 +/- grund prt, pwer +/- frame grund prt One 3-pin RS-485 Phenix cnnectr, ne RS-485 +/- grund prt One Ethernet-10/100 Ethernet prt PrtNde FPC-N35 One 6-pin Phenix cnnectr, ne RS-485 +/- grund prt, pwer +/- frame grund prt One Ethernet 10/100 BaseT prt One FTT-10 LnWrks prt Pending CE (EN55022;EN55024; EN60950), UL916, Pending FCC Class A Part 15, DNP3 Cnfrmance Tested, OPC Self-tested fr Cmpliance, RHS Cmpliant, CSA 205 Apprved BTL Marked LnMark Certified Multi-mde pwer adapter: 9-30VDC r 12-24VAC 11.5 cm L x 8.3 cm W x 4.1 cm H (4.5 x 3.2 x 1.6 in.) 0.2 kg (0.4 lbs) -40 C t 75 C (-40 F t167 F) EN ESD EN EMC EN EFT 5-90% RH (nn-cndensing) (Specificatins subject t change withut ntice) Figure 27: Specificatins Appendix E.1.1. Cmpliance with UL Regulatins Fr UL cmpliance, the fllwing instructins must be met when perating PrtNde. The units shall be pwered by listed LPS r Class 2 pwer supply suited t the expected perating temperature range. The intercnnecting pwer cnnectr and pwer cable shall: Cmply with lcal electrical cde. Be suited t the expected perating temperature range. Meet the current and vltage rating fr PrtNde/Net Furthermre, the intercnnecting pwer cable shall: Be f length nt exceeding 3.05m (118.3 ) Be cnstructed f materials rated VW-1 r FT-1 r better If the unit is t be installed in an perating envirnment with a temperature abve 65 C, it shuld be installed in a Restricted Access Area requiring a key r a special tl t gain access This device must nt be cnnected t a LAN segment with utdr wiring.

40 Triangle Tube s PrtNde Startup Guide Page 40 f 40 Appendix F. Limited 2 Year Warranty FieldServer Technlgies warrants its prducts t be free frm defects in wrkmanship r material under nrmal use and service fr tw years after date f shipment. FieldServer Technlgies will repair r replace any equipment fund t be defective during the warranty perid. Final determinatin f the nature and respnsibility fr defective r damaged equipment will be made by FieldServer Technlgies persnnel. All warranties hereunder are cntingent upn prper use in the applicatin fr which the prduct was intended and d nt cver prducts which have been mdified r repaired withut FieldServer Technlgies apprval r which have been subjected t accident, imprper maintenance, installatin r applicatin, r n which riginal identificatin marks have been remved r altered. This Limited Warranty als will nt apply t intercnnecting cables r wires, cnsumables r t any damage resulting frm battery leakage. In all cases FieldServer Technlgy s respnsibility and liability under this warranty shall be limited t the cst f the equipment. The purchaser must btain shipping instructins fr the prepaid return f any item under this warranty prvisin and cmpliance with such instructin shall be a cnditin f this warranty. Except fr the express warranty stated abve, FieldServer Technlgies disclaims all warranties with regard t the prducts sld hereunder including all implied warranties f merchantability and fitness and the express warranties stated herein are in lieu f all bligatins r liabilities n the part f FieldServer Technlgies fr damages including, but nt limited t, cnsequential damages arising ut f/r in cnnectin with the use r perfrmance f the prduct.