PDF created with pdffactory trial version

Transcription

1 J 4628 MH H 458 MH DWG. REV. ECR/NDR NUMBER REVISED BY DATE 0-02 REPLACED (" TIRES); 0-02 REPLACED (4" TIRES); REPLACED WAS X 0.00.XXXX OF FINISH: DWG. #:

2 SEE ITEM NO. NOTES PART NUMBER QTY SNAP-LOC GROMMET PIGTAIL W/ PLUGS SNAP-LOC LIGHT AMBER REFLECTOR TAPE TAIL LIGHT LH (LED) TAIL LIGHT RH (LED) WIRE HARNESS I.D. BAR LIGHT SUBM PIGTAIL PIN & LANYARD "- X 6.00" HX HD BOLT "- X.06" X 5.25" U-BOLT "-4 NYLOCK HEX NUT "- NYLOCK HEX NUT #0 X.625" HX WSHR HD SCREW "-4 X 2.25" X 5." U-BOLT "-20 CENTER LOCK NUT " FLAT WASHER "-20 X.8" LUG NUT "-2 NYLOCK HEX NUT "-2 X.25" HX HD BOLT " SAE FLAT WASHER ZINC X 4.50 TAP BOLT X.625 PAN HEAD SCREW "- X 2.06" X 5.00" U-BOLT KEEL PROTECTOR KEEL PROTECTOR LICENSE PLATE BRACKET BUSHING " LOOM HAND BOLT HAND NUT PINCH POINT LOGO TRAILERING CHECKLIST LOGO LOGO FRAME WELDMENT WINCH ASSY SWING TONGUE ASSEMBLY ROLLER ASSY ROLLER ASSY 2 42 AXLE ASSY SEE OPTIONS 4 FENDER SEE OPTIONS 44 FENDER SEE OPTIONS 45 SPRING HANGER SEE OPTIONS 2 46 TIRE SEE OPTIONS NOTES:.) SEE OPTIONS ON PAGE THREE 2.) SEE ADDITIONAL INSTRUCTIONS ON PAGE FOUR.) SEE ADDITIONAL INSTRUCTIONS ON PAGE SEVEN J 4628 MH H 458 MH REPLACED (" TIRES); 0-02 REPLACED (4" TIRES); REPLACED WAS X 0.00.XXXX OF FINISH: DWG. #:

3 ST85/80RC ST85/80DC OPTIONS PARTS FENDER ST205/5D4C ST205/5R4C SPRING HANGER TIRES J 4628 MH H 458 MH REPLACED (" TIRES); 0-02 REPLACED (4" TIRES); REPLACED WAS X 0.00.XXXX OF FINISH: DWG. #:

4 6 WIRE CLIP 8 5 GREEN/WHITE WIRES RUN DOWN THE RIGHT SIDE TUBE. WIRE CLIP YELLOW WIRE RUNS DOWN THE LEFT SIDE TUBE. WIRE HARNESS 0 THE LOOM IS PLACED AROUND THE WIRE HARNESS AT THE SWING JOINT AREA. CABLE TIES ( ) TO BE FASTENED AROUND THE LOOM (X). J 4628 MH H 458 MH REPLACED (" TIRES); 0-02 REPLACED (4" TIRES); REPLACED WAS X 0.00.XXXX OF FINISH: DWG. #:

5 DIMENSIONS MODEL # "C" "D" "E" "P" * * TRAILER ASSEMBLED TO THESE DIMENSIONS D C LOGO REFLECTOR P (0 FT. LBS. - 4X) (0 FT. LBS. - 8X) (0 FT. LBS. - 4X) 80 FT. LBS. - 0X E (0 FT. LBS. - 6X) NOTES: 4 DIMENSION IS FROM THE BACK OF THE SPRING HANGER TO THE END OF THE SIDE TUBE. 5.) TORQUE CALLOUTS IN PARENTHESIS ARE FOR REFERENCE. TIGHTEN FASTENERS UNTIL PINCHED TIGHT (DO NOT OVER TIGHTEN ROLLER PIVOT POINTS). MINOR DEFLECTION OF MATERIAL IS ACCEPTABLE J 4628 DWG. REV. ECR/NDR NUMBER MH H 458 MH REVISED BY DATE 0-02 REPLACED (" TIRES); 0-02 REPLACED (4" TIRES); REPLACED WAS X 0.00.XXXX OF FINISH: DWG. #:

6 DIMENSIONS MODEL # "B" "F" "G" "H" "S" * * TRAILER ASSEMBLED TO THESE DIMENSIONS B S H± PINCH POINT LOGO F 6 G NOTES: 6 ROLLER LOCATION IS THE DISTANCE FROM THE INSIDE OF THE SIDE TUBE TO THE OUTSIDE EDGE OF THE ROLLER MOUNTING BRACKET. J 4628 MH H 458 MH REPLACED (" TIRES); 0-02 REPLACED (4" TIRES); REPLACED WAS X 0.00.XXXX OF FINISH: DWG. #:

7 WINCH MOUNTING INSTRUCTIONS VIEW WINCH STRAP WITH HOOK RUNS UNDER THE ROLLER BEFORE BEING HOOKED TO THE BOW EYE OF THE BOAT. ROLLER MOUNTING INSTRUCTIONS VIEW 2 SWING TONGUE MOUNTING INSTRUCTIONS VIEW 2 J 4628 MH H 458 MH REPLACED (" TIRES); 0-02 REPLACED (4" TIRES); REPLACED WAS X 0.00.XXXX OF FINISH: DWG. #: