VIEW A KARAVAN T R A I L E R S A MJH A FINISH: DWG. #: KRUS-3100-DB10-74-ST SEE B.O.M. N/A N/A

Transcription

1 VIEW A A A 55 MJH XX 0.00.XXXX 0.00 OF A

2 ITEM NO. NOTES PART NUMBER QTY MUD FLAP BRACKET BRAKE LINE FENDER TILT PIN "- X.0" X.50" U-BOLT "- X.0" X 5.25" U-BOLT "-8 NYLOCK HEX NUT "- CENTERLOCK HEX NUT "-4 X 2.25" X 5." U-BOLT "-20 X.75" HX HD BOLT "-20 CENTER LOCK NUT "-20 REG. HEX NUT " SPLIT LOCK WASHER "-20 X.8" LUG NUT "-2 NYLOCK HEX NUT "-2 X.25" HX HD BOLT " SAE FLAT WASHER ZINC "-8 X.50" HX HD BOLT "-4 CENTERLOCK HEX NUT "-20 NYLOCK HEX NUT SCREW LOBE TRUSS HD /4"-20 X -/2" "- X 5.75" HX HD BOLT " FLAT WASHER "- TOP LOCK HEX NUT KEEL ROLLER HOLE TIRE & RIM BUSHING MUD FLAP LOGO LOGO SPRING HANGER WELDMENT FRAME WELDMENT WINCH ASSY AXLE ASSEMBLY ROLLER ASSY ROLLER ASSY TONGUE ASSY SWING X4 BRK 8 LIT-0047 SERIAL TAG ALUM. AUS NOTE:.) SEE ADDITIONAL INSTRUCTIONS ON PAGE SIX. A 55 MJH XX 0.00.XXXX OF A

3 VIEW B GREEN/WHITE WIRES CONNECT TO THE REAR HARNESS DOWN THE LEFT SIDE TUBE THE TAIL LIGHT IS MOUNTED TO THE CENTER HOLES OF THE TAIL LIGHT BRACKET. YELLOW/WHITE WIRES CONNECT TO THE REAR HARNESS DOWN THE LEFT SIDE TUBE WIRE CLIPS BRAKE LINE BRAKE LINE PIGTAIL THE TAIL LIGHT IS MOUNTED TO THE CENTER HOLES OF THE TAIL LIGHT BRACKET. WIRE CLIPS THE LOOM IS PLACED AROUND THE WIRE HARNESS. CABLE TIES (2-0004) TO BE FASTENED AROUND THE LOOM (X). B THE LOOM IS PLACED AROUND THE WIRE HARNESS AND BRAKE LINE AT THE SWING JOINT AREA. CABLE TIES (2-0004) TO BE FASTENED AROUND THE LOOM (X). A 55 MJH DWG. REV. ECR/NDR NUMBER REVISED BY DATE BLUE WIRE RUNS UP TO THE ACTUATOR SOLENOID.XX 0.00.XXXX 0.00 OF A

4 DIMENSIONS "B" "C" "D" "E" "P" Model # POST UP REF AXLE LOGO * * SEE JOB PART NUMBER FOR WHICH TRAILER SETUP TO USE D TRAILER CHECK LIST 0 FT. LBS. - 4X C B 0 FT. LBS. - 8X P 0 FT. LBS. - 4X E 80 FT. LBS. - 0X SWUNG 25. (0 FT. LBS. - X) 4.4 NOTES: 2 DIMENSION IS FROM BACK OF SPRING HANGER TO THE BACK OF THE FRAME. A 55 MJH XX 0.00.XXXX OF A

5 Dimensions "F" "G" "S" Model # FRONT REAR STAMP * * SEE JOB PART NUMBER FOR WHICH TRAILER SETUP TO USE C VIEW C.0 S LIT-0047 F G NOTES: ROLLER LOCATION IS THE DISTANCE FROM THE INSIDE OF THE SIDE TUBE TO THE OUTSIDE EDGE OF THE ROLLER BRACKET. A 55 MJH XX 0.00.XXXX OF A

6 VIEW MUD FLAP MOUNTING INSTRUCTIONS 2 VIEW 2 ROLLER MOUNTING INSTRUCTIONS ROLLER GUIDE VIEW ROLLER MOUNT TILTED DOWN (SHOWN): WINCH STRAP WITH HOOK RUNS UNDER THE ROLLER GUIDE BEFORE BEING ATTACHED TO THE BOW EYE OF THE BOAT. MOUNT TILTED UP: WINCH STRAP SHOULD BE RUN UNDER THE ROLLER & OVER THE ROLLER GUIDE BEFORE BEING ATTACHED TO THE BOW EYE OF THE BOAT. REAR CROSS MEMBER A 55 MJH DWG. ECR/NDR REVISED DATE.XX 0.00.XXXX 0.00 OF A