BS1015C USER S MANUAL. MA13-02/B 12/09/2011

Transcription

1 BS1015C 12/09/2011

2 INDEX Page 1. DESCRIPTION 3 2. INSTALLATION 2.1. Scale assembly 2.2. Lcatin and setting 2.3. Startup 3. OPERATION 3.1. LCD symbl descriptin 3.2. Key functins 3.3. Weighing 3.4. Taring 3.5. Hld 4. SETUP 4.1. Cnnecting with PC 5. MAINTENANCE AND CLEANING 5.1. Instructins fr charge and cnnect 5.2. Instructins fr replacing batteries 5.3. Envirnmental 5.4. Equipment dispsal TROUBLESHOOTING HEIGHT ROD ACCESSORIES 7.1. Height rd assembly 7.2. Battery installatin 7.3. Key functins 7.4. Calibrating the height rd 7.5. Using the height rd 7.6. Trubleshting 7.7. Specificatins TECHNICAL SPECIFICATIONS WARRANTY CERTIFICATE CE DECLARATION OF CONFORMITY 21 2

3 1. DESCRIPTION (1) Display unit (2) Display munting clumn (3) Tray (4) Scale platfrm (5) Adjustable feet 3

4 2. INSTALLATION Befre putting the device int use, please read with care the infrmatin given in the Operating Instructins. They cntain imprtant instructins fr installatin, prper use and maintenance f the device. The manufacturer shall nt be liable fr damages arising ut f failure t heed the fllwing instructins: When using electrical cmpnents under increased safety requirements, always cmply with the apprpriate regulatins. Imprper installatin will render the warranty null and vid. Ensure the vltage marked n the pwer supply unit, matches yur main pwer supply. This device is designed fr use indrs. Observe the permissible ambient temperatures fr use. The device meets the requirements fr electrmagnetic cmpatibility. D nt exceed the maximum values specified in the applicable standards SCALE ASSEMBLY Indicatr can be installed in FIXED and ADJUSTABLE mde Rute the cable thrugh the tube FIXED MODE ADJUSTABLE MODE Screw the hle belw Screw the hle abve 4

5 1. Rute the cable thrugh the clumn. 2. Rute the cable thrugh the base and screw clumn t base. 3. Tighten the three base screws by turning clckwise. 4. Cnnecting the cable 5. Align the bracket n the base and tighten the screws. 6. Installing the adjustable ft NOTE: Make sure that the weighing tray is installed prperly and at the right psitin. 7. Install the tray t the prper lcatin 5

6 8. Install the tray at the prper lcatin and tighten the screws n bth sides. 9. Assembly finished. 10. Adjust fur rubber feet t center bubble level LOCATION AND SETTING We strngly recmmend yu use this device n flat and hard surface. Any sft surface, like carpet will cause inaccuracy STARTUP Cnnect the equipment t the pwer supply using the AC adaptr. Press the ON/OFF buttn in the indicatr. Wait until 0 appears n display. 6

7 3. OPERATION Befre reading detailed instructins n hw t use all the weighing functins that are built int yur scale, please read the fllwing imprtant guidelines: Always be sure that the display shws `Zer` befre use, if it des nt then please press the ZERO key. The equipment is designed t detect when a stable weight is achieved, yur reading shuld be taken at this pint LCD SYMBOL DESCRIPTION PRE-TARE Indicatin Stable symbl BMI Indicatin HOLD Indicatin NET WEIGHT Indicatin WEIGHT Indicatin kg Minr weight Zer symbl Lw Battery Display [ 0 ] HOLD NET WEIGHT Descriptin Zer symbl: If the scale des nt shw exactly zer value althugh the scale pan is unladed, press the [ 0 ] key. After a shrt waiting time, the scale will be zered again. Stable symbl: If the display shws the stabilizatin display [ο], the scale is in the stable cnditin. When the scale is in the unstable cnditin, the stabilizatin display [ο] disappears. Hld functin / saving functin is active. The net weight is displayed. The present weight value is displayed. 7

8 3.2. KEY FUNCTIONS Designatin ON/OFF-switch HOLD buttn ZERO setting key TARE buttn Functin Turn ON/OFF the scale T hld weighing result n the display / determine stable weighing value T reset the display t 0.0kg display / Zer the scale (±2% f full capacity) Tare weight during weighing prcess 3.3. WEIGHING Switch n the scale with the [ON/OFF] key. The diagnstic scale self-check is perfrmed and then the sftware versin is displayed. The scale is ready fr weighing when the 0,00 kg weight display is shwn. NOTE: If 0,00 kg wn t display n the screen, press [ 0 ] key t zer the scale, [ 0 ] can be used any time t zer the scale. Place a persn in the middle f the scale. Wait until the stability display (ο) is shwn and then read the weighing result. DIRECTION: If a persn is heavier than the weighing range, the display will shw the Err symbl (= verlad) TARING Tare allws the user t zer the instrument t cancel the weight f a cntainer/ clthes frm the reading f the instrument, thus giving the true weight f the prduct/ persn being tested. Turn n the scale using [ON/OFF] key. When 0,00 kg displays n the screen and scale beeps twice, place the bject (clthes) t be tared n the tray. Press [TARE] key after the weight stabilizes and stable sign appears n the display. Display will return t 0,00 kg Place the item/ baby t be weighed (withut remving the tare bject). The weighing result is the Net weight f the item / baby. T delete the saved tare value, remve the tare bject frm the tread platfrm and press [TARE] key. 8

9 3.5. HOLD The scale is prvided with the integrated hld functin (determinatin f average value). It enables peple t be weighed accurately althugh they are nt still n the scale plate. NOTE: Determinatin f average value is nt pssible when a persn mves t much. Switch n the scale with the [ON/OFF] key. The scale self-check diagnstic is perfrmed. The scale is ready fr weighing when the 0,00 kg weight display is shwn. Place a persn in the centre f the scale plate. Press the [HOLD] key. When the triangle is flashing n the display, the scale takes sme measuring values and then the calculated average value is displayed. Remve the bject/ baby frm the scale platfrm. The bject/ baby s weight reading will remain n the display. Press the [HOLD] key again t return the scale t the nrmal weighing mde. HOLD functin can be activated befre r after putting the weight n the platfrm. In case f weighing babies that mve a lt, it is recmmended t press [HOLD] key befre the persn mves n the platfrm. 9

10 4. SETUP Switch ON the scale and lng press [ZERO] key fr 3 secnds. First SETUP and then A.OFF will display successively. Aut-ff time setup This enables peratr t select the aut turn OFF time f the device. Aut ff time: 120 sec/180 sec/240 sec/300 sec/off Buzzer n/ff setup This enables peratr t select beep sund ON/OFF. Buzzer: zer: On/Off NOTE: T cnfirm the settings, please press HOLD when END displays n the display CONNECTING WITH PC The equipment can be cnnected t PC t transfer the weighing results. 1. Start Hyper Terminal Start Hyper Terminal prgram frm clicking: Start Menu Prgrams Accessries Cmmunicatin Hyper Terminal. 2. New Cnnectin Descriptin Give new cnnectin a name then click OK. 3. Select Yur COM Prt Click Cnnect t select yur COM prt. Usually there s nly ne ptin fr select. Then click OK. 4. Prt Settings Click Bits per secnd t set up rate at 9600, Data bits at 8, Parity at Nne, Stp bits at 1 and Flw cntrl at Hardware. Then click OK t cmplete yur setting. 5. Output Data When the patient has been weighed and BMI calculated, simply press the PRINT key t utput data frm scale t PC r an Optinal Printer. Parameters f RS232 interface Set parameters f the scale interface n the cnnected device. It is nt pssible t change the scale parameters. Baud rate: 9600 bps 10

11 Parity check: Nne Data length: 8 bits Stp bit: 1 bit Handshake: RTS/CTS Data cde: ASCII. 11

12 5. MAINTENANCE AND CLEANING The scale des nt require any rutine maintenance. Hwever, we recmmend checking the scale s accuracy at regular intervals. The regularity f these checks is dependent n the level f use and the state f the scale. We wuld recmmend using alchl based wipes r similar when cleaning the scale. Please d nt use large amunts f water when cleaning the scale as this will cause damage t the scale s electrnics, yu shuld als refrain frm using crrsive liquids r high pressure washers. Always discnnect the scale frm the main pwer supply befre cleaning INSTRUCTIONS FOR CHARGE AND CONNECT If L is displayed n the LCD, yu shuld charge scale with AC adaptr. Lcate adaptr plug at the rear f indicatr. CAUTION: Always cnnect the AC adaptr t the indicatr befre cnnecting t the main pwer supply. Please discnnect the adaptr frm main pwer supply befre indicatr INSTRUCTIONS FOR REPLACING BATTERIES Remve the battery cver Take the battery husing ut Replace new batteries Make sure batteries are well installed Reinstall the battery husing Reinstall the battery cver 5.3. ENVIRONMENTAL All batteries cntain txic cmpunds; dispsal f batteries shuld be delegated t a cmpetent rganizatin, cmplying with the depsit f Pisnus Waste Regulatin Please d nt incinerate batteries. The ptimum perating temperature fr the scale is 5ºC t +35ºC; althugh it will perate at higher and lwer temperatures the scale s battery life will adversely be affected EQUIPMENT DISPOSAL All electrical and electrnic prducts shuld be dispsed f separately frm the municipal waste stream via designated cllectin facilities appinted by the gvernment r the lcal authrities. This crssed-ut wheeled bin symbl n the prduct means the prduct is cvered by the Eurpean Directive 2002/96/EC. The crrect dispsal and separate cllectin f the equipment will help prevent ptential negative cnsequences fr the envirnment and human health. It is a precnditin fr reuse and recycling f used electrical and electrnic equipment. 12

13 6. TROUBLESHOOTING Errr Message Reasn Lw Battery: This warning shws that the vltage f battery is t lw t use Overlad: The ttal lad exceeds the maximum capacity f the scale Cunting errr (t high): Indicates that the signal frm the lad cell is t high Cunting errr (t lw): Indicates that the signal frm the lad cell is t lw Zer cunt ver calibratin zer range +10% while pwer n Zer cunt under calibratin zer range -10% while pwer n EEPROM Errr: Indicates that there is a fault with the scale s sftware Actin Please replace a new battery r plug the AC adaptr fr peratin Please reduce the lading and try again This errr is nrmally caused by a serius fault n the scales such as faulty lad cell r wiring. Please cntact the lcal service representative. This errr is nrmally caused by a serius fault n the scales such as faulty lad cell r wiring. Please cntact the lcal service representative. Please recalibrate the instrument Please recalibrate the instrument This errr is nrmally caused by a serius fault n the scales such as faulty lad cell r wiring. Please cntact the lcal service representative. 13

14 7. HEIGHT ROD ACCESSORIES AC2080D AC2080D is a digital height rd t be munted n the scale with measuring range f 35~80cm. AC2080D have LCD display fr cnvenient, accurate and quick height measurement. AC2080M AC2080M is a mechanical height rd t be munted n the scale with measuring range f 35~80cm, AC2080M dn t have LCD display HEIGHT ROD ASSEMBLY 1. Fix bracket n the tray with tw screws 2. Assemble the height rd t the bracket 14

15 3. Press the buckle t secure the height rd is well installed 4. Assembly cmplete 7.2. BATTERY INSTALLATION AC2080M dn t need batteries t perate AC2080D Installing battery AAA 1.5V x 2 in battery husing next t LCD display. WARNING: If the height rd is nt in use fr lng time, take ut the batteries and stre them separately, in case f any leakage frm battery wuld damage the measuring rd KEY FUNCTIONS Keys ON/OFF UNIT HOLD RESET Descriptin Press t switch n and ff. T select the measurement unit between cm and inch. T enable value stre functin during measuring. Current height value f user will be stred and displayed. Press again t disable the functin. RESET key is fr user t calibrate false reading. Slide right feet piece t the left at length f 35cm. Press RESET key t calibrate the height rd. LCD will display 35.0cm which means the height rd has been well calibrated. 15

16 7.4. CALIBRATING THE HEIGHT ROD AC2080D 1. Installing battery 2. Press ON/OFF t switch n LCD 3. Sliding feet piece left t the end. 4. Press RESET buttn t calibrate at 35.0cm 7.5. USING THE HEIGHT ROD AC1200D 1. Extend the height rd fr use 2. Place the baby with his head tuching the left tp f the height rd 3. Straighten baby s feet 16

17 4. Slide the right piece f the height rd until it tuches the baby s feet 5. The LCD is displaying the baby s lenght 6. Press HOLD buttn t memrize the length reading. 7. Press HOLD again t disable the functin and return t nrmal mde. AC1200M 1. Extend the height rd fr use 2. Place the baby with his head tuching the left tp f the height rd 3. Straighten baby s feet 4. Slide the right piece f the height rd until it tuches the baby s feet 5. Take reading frm Picture A 17

18 6. Pull ut t use 7. Remve baby 7.6. TROUBLESHOOTING If feet piece is lse please re-assemble feet piece as belw. NOTE: If the reading has errr, please fllw RESET prcedure fr calibratin TECHNICAL SPECIFICATIONS Mdel AC2080D AC2080M Type Scale munted height rd Keys Hld, Reset, Unit - Measurement range 35~80cm Graduatins 1mm Dimensins (W x H x L) 29 x 7 x 62 cm Weight 700 g Pwer Supply 2 * AAA-size batteries - Temperature range +10ºC up t +40ºC 18

19 8. TECHNICAL SPECIFICATIONS Mdel: BS1015C Capacity: 15 kg x 2g <6 kg > 5g Display: LCD display with 5 and 1/2 digits. Digit size: 24mm Tray dimensins: 550 x 290 mm Pwer supply: AC adapter 15V 300mA /Rechargeable Battery Key Functins: ON/OFF,ZERO, PRINT, BMI, HOLD, PRE-TARE,TARE, CLEAR, ENTER, 0~9, M1-5 Operatin temperature: 5ºC / 35ºC 19

20 9. WARRANTY CERTIFICATE We prvide a 1-year guarantee frm the date f purchase. The guarantee cvers manufacturing defects r defects ccurring as a result f nrmal use and peratin. It excludes all remvable parts such as batteries, wires, pwer supply devices, etc. Faults falling within the guarantee perid shall be rectified free f charge upn presentatin f the purchase receipt fr the appliance. N ther rights can be taken int cnsideratin. Return shipment is at the custmer's expense if the appliance is anywhere ther than at the custmer's headquarters. In the event f damage during shipment, guarantee rights will be granted nly if the appliance is shipped in the riginal packaging. Yu are therefre recmmended t keep the riginal packaging. Fllwing expiry f the guarantee perid, all services requested will be dealt with by ur specialist technicians at the user's expense. 20

21 10. CE DECLARATION OF CONFORMITY CE DECLARATION OF CONFORMITY FABRICANTE PRODUCTO: PRODUCT MANUFACTURER: DIRECCIÓN: ADDRESS DAVI & CIA S.L. C/ Murcia, 35, Nave G Plígn Industrial Can Calderón E08830 Sant Bi de Llbregat BARCELONA - ESPAÑA DECLARAN BAJO SU RESPONSABILIDAD QUE EL PRODUCTO: DECLARE UNDER THEIR RESPONSIBILITY THAT THE PRODUCT Marca Brand Nmbre Name Tip Type Finalidad Prevista Intended Use DAVI & CIA BS1015C EQUIPO ELECTRONICO Electrnic equipment Equip pesapersnas. Weighing equipment. CUMPLE LOS REQUISITOS DE LAS DIRECTIVAS: CONFORMS WITH THE REQUISITES OF THE DIRECTIVES EC Directive 2004/108/EC EC Directive 2006/95/EC EC Directive 93/42/EEC Directiva de Cmpatibilidad Electrmagnética (Electrmagnetic Cmpatibility Directive) Directiva de Baja tensión (Lw Vltaje Directive). Aplicable únicamente a las básculas cn aprbación médica (Applies nly t scales with medical apprval). FECHA: 12 de Diciembre de 2010 DATE: 12 th December 2010 Nmbre: Name Firmad: J.Masana Signed Carg: Functin Gerente DAVI & CIA 21

22 This manual and ther supprt dcuments are available n the web C/ Murcia, 35 Nave G Pl.industrial Can Calderón. E Sant Bi de Llbregat. Barcelna. Spain Tel Fax inf@davicia.cm 22