USER`s Manual. Swivelling semi-automatic press. Swivelling manual press TECHNICAL DATA. - works without compressor

Transcription

1 USER`s Manual Swivelling semi-autmatic press Swivelling manual press TECHNICAL DATA - wrks withut cmpressr - pens autmatically ( nly Swing S ) - swivels autmatically aside ( nly Swing S ) Dimensins in cm: H 70 xw54xd70cm (withut table) Weight (withut table) 62 kg Vltage 230 VAC Pwer (38 x 45 cm) 2 kw Pwer (40 x 50 cm) 2,3kW Temperature range C Time 0-9:59Min. Max. pressure ca.1050 kg Max. variatin f temperature f the heat platen at 180 C (interir temperature f the heat platen) -1/+3 C Interchangeable heat platens Interchangeable base platens 10x13cm 20x20cm 38x45cm 40x50cm caps ptin 20 cm 38x45cm 40x50cm 20x20cm 12x12cm 38 cm Fr caps 8x16cm 10x45cm 43 cm 1

2 + Fuse 12 A Display Main switch Temperature and time setting Lever Lcking screw fr swivel autmatic ( nly Swing S ) Pressure switch OFF ( nly Swing S ) Electr magnet ( nly Swing S ) Grease nipple Clamping blts fr heat platen Heat platen Base platen Caps ptin ADJUSTMENT OF THE SWIVELLING AUTOMATIC ( nly Swing S ) 1. Swivel mvable part f the press and the heat platen t the right side. 2. Turn lcking screw f the swivel autmatic t the right. Pressure adjustment Please unfix the lcking screw t switch ff the swivel autmatic. ATTENTION! The press needs t be set up abslutely hrizntal t make sure the swivel autmatic is wrking. Pressure Adjustment 1. Put yur textile nt the base platen. 2. Mve the heat platen t its lwer psitin and check the cntact pressure. 3. Turn the large wheel ( lcated underneath the base platen ) t the right (-)until the heat platen des nt build up any pressure. In this psitin the heat platen is suppsed t slide slightly n the base platen. This is ur starting psitin. The pressure equals " 0". 4. The max. Pressure f the press is 4 cmplete rtatins f the wheel t the left. Fr example: When number 2 is faced frward in the starting psitin zu can turn the wheel 4 times t the left until number 2 is facing frward again after the 4th rtatin. EXAMPLE: Pressure settings Flck transfers 0,5-1,5 Ultraflex 1-2,5 Therm transfers 2-4 Sublimatin 1-2,5 Puzzel 3-4 ATTENTION! After each change yu shuld clse the press nce t check the new pressure setting. Damages due t excess pressure settings are excluded frm the guarantee x = max. 2

3 + SWITCH ON This device may nly be perated by trained staff after reading the OPERATOR s MANUAL. Befre yu switch n the device, please check if yur scket is in prper cnditin and if the grunding wire is cnnected prperly. The green tggle switch activates the press. The display shws the current temperature f the heat platen and the press will heat immediately until the indicated temperature is reached ( LED 1 is shining ). SAFETY Fr ptimum utput and safety it is recmmended t read and fllw the USER s MANUAL carefully. Please nte that nly ne persn is allwed t wrk with the press at the same time. Minrs are nt allwed t wrk with the press either. In case f an emergency press the main switch immediately. MAINTENANCE All maintenance wrks shuld be dne when the device is switched ff. Yu have t pull the plug ut f the scket befrehand. When replacing the heat platens yu will have t wait until the heat platens have cled dwn cmpletely! DANGER OF BURNING!!! There is ne grease nipple n the press. It shuld be lubricated with a grease gun every fur weeks. Make sure that the grease infiltrates the bearing when lubricating. The grease has t be temperature-resistant up t 160 C. CLEANING The device shuld be cleaned with a sft clth. Use dmestic dish washing liquid. Scrubbing spnges, slvents r petrl are nt recmmended. REPLACE SILICONE PAD When replacing the silicne pad the device has t be cld. Remve the ld silicne pad cmpletely frm the base platen. Use a pallette knife t equally spread ut temperature-resistant silicne. Then apply the new silicne pad. Base platen Put a plate nt the silicne pad and lad with weights ( apprx. 20kg ) straight: Let dry fr 24 hurs. Part fr caps: Apply the cld heat platen nt the new silicne pad. Fix bth plates with paper adhesive tape. Let dry fr 24 hurs. The silicne pad shuld be abut 1-2 cm bigger than the base platen. Use a cutter t cut ff the edges after yu have sticked bth plates tgether. 3

4 Swing S - Cabinet stand 1. Please remve the prtective fil, unfix the lcking screws and take ut the press (Pic 1 and 2). ATTENTION!!! The head f the press may slide aside. The prcesses f taking the press ut and attaching it have t be dne by tw persns. 2. Unfix the screws (Pic 3). Lwer the table (Pic 4) and screw the table-legs tight (Pic 5). 3. Put the press n the cabinet stand and blt them tgether. The frnt-side f the press with the lever has t fit int the hle f the cabinet stand (Pic 6)

5 Greasing Befre yu start greasing make sure the press is switched ff and the heat platen is cld. Please d als pull ut the plug f the scket. Yu shuld grease after a max. f 200 perating hurs r at the latest 4 weeks time. The grease has t be temperature-resistant up t 160 C. There are 4 parts suppsed t be greased (Swing and Swing S): 1. There are tw hles n the yellw lever. 2. Left and right f the shrt shaft in the yellw lever. 3. The secnd shrt shaft under the yellw lever. 4. The fitting f the heat platen. Please use a grease gun. Grease LITEN Lt-43 1) 2) 3) 4) The fitting f the heat platen. Please use a grease gun. Mve the press t the left and right when greasing t make sure the grease infiltrates int the fitting. 5

6 USER s Manual PROGRAMMING Temperature Zeit Prgram 1. Setup 5 sec. 2. Temperature +/- 3. Setup 1 sec. 4. Time +/- 5. Setup 1 sec. 6. End 1. Hld buttn 1 fr 5 secnds until LED1 is blinking. 2. LED 1 is blinking and the display shws the preset temperature. The prgramming mde has been switched n. 3. Set new temperature with the buttns -2 r Cnfirmatin 4. Press buttn 1. The display shws the preset time. Change time setting with buttns -2 r Press buttn 1 t switch ff the prgramming mde. Temperature in C LED 1 - The press is heating LED 2 - Blink dide, prgramming mde switched n LED 3 - ( nt activ ) LED 4 - ( nt activ ) TIME CONTROL Press buttn 2, the preset time setting is shwn n the display. Max. time 9 minutes 59 secnds. Example: Time setting 1 minute 15 secnds. Minutes TEMPERATURE CONTROL Press buttn 3, the preset temperature is shwn n the display. Example: Settings fr the press This press is used t apply transfers and transfer fils n textiles. Please get in tuch with the manufacturer f the textiles, in rder t achieve gd results. Sme settings: Fil Flex - Fil Flex S Fil Flck Fil Velcut C time 12 sec C time 12 sec C time 15 sec C time 15 sec. All infrmatin withut engagement. Please arrange wn tests befre manufacturing. 6

7 SCHALTPLAN SCHEMATIC (electrical diagram) Thermregulatr-timer ROM C F 12VDC CRYDOM S1 S S6 K - - Pwer supply unit Netzteil/zasilacz 12VDC S4 S5 12VDC S1 Zeit aus 12V+ time ff - Setup F2 1,5A / Pressure OFF Druck AUS Elektrmagnet Electr magnet ( nly Swing S ) ( nur Swing S ) S2 blau Zusatzschalter/ additinal switch VDC Relais 50A Przekaznik elektrniczny relay CRYDOM 50A 230VAC Stecker/Wtyczka/Plug VAC L Stecker/Wtyczka/Plug Temperatursicherung/Temperature fuse 1F25 FILTER S10 Hauptschalter/ Wlacznik glówny / Main switch S1 time start... (czarny / schwarz / black ) S4 setup...(zlty / gelb / yellw ) S5 [-]Temperature... (zielny / grün / green) S6 [ +] Zeit/time...(Brazwy / braun / brwn) Temperatur(e)sensr ( - )...(niebieski / blau / blue) Temteratur(e)sensr (+)...(czerwny / rt / red) F1 bezpiecznik / Sicherung / fuse 10A F2 bezpiecznik / Sicherung / fuse 12VDC 0,4A 12V+ czerwny / rt / red 12V- niebieski/ blau / blue 3+6grzalka / Heizelement / Heating element czujnik / Temperatursensr / Temperature sensr 7 uziemienie / Schutzleitung / Grunding wire Temperatur(e)sensr KTY 84-1 A3K1 Z 540 czarny schwarz 230VAC black Heizelement/grzalka/heating element Heizelement/grzalka/heating element S W Heizplatte/plyta grzewcza/heat platen F czarny schwarz 230VAC black 230W Temperatur(e)sensr 230W Heizplatte/plyta grzewcza/heat platen 8 x 16 cm 2 5 niebieski/ blau / blue Temperatur(e)sensr 1 4 czerwny/ rt / red + Temperatur(e)sensr Stecker/Wtyczka/Plug 0 N 3 6 7

8 TESTING REPORT E visat visat PRESS4050 visat CAP Base (varnish, greasing f shafts) Heat and base platens, symmetry, silicne, tefln Hurs f wrk at 220 C... Electrical cnnectin, grunding wire, pwer cable Test with transfer fil Electrnics, max temperature 220 C, inspectin f all functins Warning stickers Hurs f wrk at 180 C... Packaging Temperature tlerance at 180 C...-/...+ C Serial number... EC declaratin f cnfrmity - Accrding t the EC directive 89/37 EC The Walter Schulze GmbH Schmalenbachstr Berlin hereby declares as Eurpean agent fr the manufacturer Rmanik that the fllwing described machine: heat press....serial number... accrds t the terms f the fllwing EC directives: Machine directive ( 89/37) Lw vltage directive (72/23) EMV-directive (89/336) Used standards and technical specificatins: EN 292-1, EN safety f machines EN electrical equipment f machines Berlin... Peter Meidinger CEO 8