MOBILE MIXERS PARTS MANUAL TRAILER AND STATIONARY MODELS. Serial number up to

Transcription

1 MOBILE MIXERS PARTS MANUAL TRAILER AND STATIONARY MODELS Serial number up to Harsh International, Inc. 600 Oak Ave. Eaton, CO (970) Fax: (970) lpd@harshenviro.com Price: $.50 Parts book number: 10875B

2 TABLE OF CONTENTS Parts Ordering Information...3 Mixer Orientation...4 Trailer Frame...5 Driveline Trailer...6 Auger Assembly...8 Rear Drive Discharge (detail)...1 Discharge Assembly...14 Trailer Hydraulics...16 Electric Control-Hydraulics...17 Integral Hydraulics...18 Drop Chute Cylinder...19 Discharge Door Cylinder...0 Liners & Hay Shelves...1 Door Marker Trailer...3 Rear Oil Bath...4 Mixer Decals...5 Tub Guard...7 Stationary Parts...8 Index...9

3 PARTS ORDERING INFORMATION To assure continued safe and efficient operation and to maintain the validity of your warranty use only genuine Harsh replacement parts. To obtain the correct parts for your mixer, contact the nearest Harsh equipment dealer in your area. If no Harsh dealer is available, contact Harsh International Inc., 600 Oak Avenue, Eaton, CO 80615, (303) When ordering parts, be sure to know the Model and Serial numbers of the machine. For the quickest service when ordering by phone, be prepared to state the part number and description as well as the Parts Manual part number, the page number and item number of the part(s) you are ordering. Always have repairs performed by qualified Service Personnel from your Harsh dealer. All information, illustrations and specifications contained in this manual are based on the latest product information available at the time of printing. Harsh International, Inc. reserves the right to make changes to manuals, parts or assemblies at any time without prior notice. REPLACEMENT MANUALS Replacement or extra Operator's Manuals and Parts Manuals are available from Harsh or contact your local dealer. All Operator's Manual's and Parts Manuals are ordered by Model number and Serial number of your unit. There is a nominal cost for each manual ordered.!!!! IMPORTANT!!!! Before attempting to operate, inspect, adjust, repair or replace any part of your machine be sure to be thoroughly familiar with your Operator's Manual and observe all safety notices; both printed in the manual and on decals located on the machine. FAILURE TO OBSERVE THESE SAFETY RULES COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE! 3

4 Mixer Orientation 4

5 TRAILER FRAME 1 A17879 AR TRAILER FRAME ASS'Y (03) HUB 1 A17878 AR TRAILER FRAME ASS'Y (53) BEARING CUP *1 A1819 AR TRAILER FRAME ASS'Y (303) NUT *1 A17887 AR TRAILER FRAME ASS'Y (303) HUB CAP NUT COTTER PIN WASHER, LOCK WASHER SCREW, HEX HD CAP BEARING CONE SCREW, HEX HD CAP * TIRE, 10 X 0 RAD. IMPLEMENT C 7 NUT * TUBE, 10 X 0 RADIAL WASHER, LOCK * RIM, 8 X 0-8 HOLE SCREW, HEX HD CAP *10589 WHEEL ASSEMBLY, STANDARD SCREW, HEX HD CAP BOLT, LUG 10 A TONGUE BUMPER, REAR WASHER, LOCK BUMPER, EXTENSION NUT JACK 13 A HITCH FENDER, TUB MOUNT (03,303) SCREW, HEX HD CAP FENDER, TUB MOUNT RH (53) 15 A155 1 AXLE ASSEMBLY FENDER, TUB MOUNT LH (53) NUT SCREW, HEX HD CAP WASHER, LOCK * TIRE, 40 X 14 AIRPLANE SPINDLE * TUBE,40 X 14 AIRPLANE *A15374 SPINDLE ASSEMBLY * RIM, 16 X 13-8 HOLE SEAL * FLAP, 16 X 13 CEN. VALVE HOLE BEARING CONE *1058 WHEEL ASSEMBLY, AIRPLANE BEARING CUP NOTE: AR - AS REQUIRED *1 - A TRAILER FRAME ASSEMBLY FOR 303 WITH LOAD CELL. *1 - A TRAILER FRAME ASSEMBLY FOR 303 WITH WEIGH BAR. *A INCLUDES SPINDLE #15373, NUT #10196, WASHER #100173, AND COTTER PIN # *9, 30, 31 - STANDARD TIRE ASSEMBLY. * INCLUDES TIRE #10130, TUBE #101303, AND WHEEL # *39, 40, 41, 4 - OPTIONAL TIRE ASSEMBLY. * INCLUDES TIRE #10593, TUBE #10594, WHEEL #10595, AND FLAP #

6 DRIVELINE - TRAILER 6

7 DRIVE LINE TRAILER SCREW OUTER PROFILE DRIVE LINE SHIELD ROLL PIN WASHER, FLAT YOKE LOCK WASHER CROSS NUT NUT KEY SHEAR CLUTCH ASSEMBLY BEARING, PILLOW BLOCK SHEAR BOLT SCREW CV CONE LOCK WASHER YOKE, 540 RPM 6 SPLINE C 4 NUT CROSS DRIVE SHAFT (03, 53) DOUBLE YOKE DRIVE SHAFT (303) INNER YOKE CROSS INNER PROFILE SLIP YOKE SHIELD TUBE DRIVE SHAFT (03, 53) RIB CONE DRIVE SHAFT (303) WASHER YOKE SCREW INPUT ADAPTER SHAFT NUT, HEX 0 A INPUT ADAPTER SHEAR YOKE BEARING HUB, 1 1/4 DIA. A INPUT ADAPTER SHAFT ASSEMBLY BALL GEAR BOX PLANETARY 10.8: ZERK, GREASE RIB CONE DRIVE SHAFT RPM, 6 SPLINE SHIELD TUBE SCREW BEARING PLATE SET SCREW 7

8 AUGER ASSEMBLY 8

9 AUGER ASSEMBLY 1 A AUGER, UPPER RIGHT (03 FEED) 13 A STUB SHAFT, REAR 1 A AUGER, UPPER RIGHT (03 HAY) SCREW, HEX HD CAP 1 A AUGER, UPPER RIGHT (53 FEED) WASHER, FLAT 1 A AUGER, UPPER RIGHT (53 HAY) WASHER, LOCK 1 A AUGER, UPPER RIGHT (303 FEED) NUT 1 A AUGER, UPPER RIGHT (303 HAY) SCREW, HEX HD CAP A AUGER, LOWER RIGHT (03 FEED) SPACER, STUB SHAFT A AUGER, LOWER RIGHT (03 HAY) A AUGER, LOWER RIGHT (53 FEED) 5" TUBE FLIGHTING AND KICKERS A AUGER, LOWER RIGHT (53 HAY) AR FLT, RIGHT HAND (FEED) A AUGER, LOWER RIGHT (303 FEED) AR FLT, LEFT HAND (FEED) A AUGER, LOWER RIGHT (303 HAY) AR FLT, RIGHT HAND (HAY) 3 A AUGER, LOWER LEFT (03 FEED) AR FLT, LEFT HAND (HAY) 3 A AUGER, LOWER LEFT (03 HAY) AR KICKER, STANDARD 3 A AUGER, LOWER LEFT (53 FEED) AR KICKER, SHARK FIN 3 A AUGER, LOWER LEFT (53 HAY) AR KICKER, STANDARD ND PART 3 A AUGER, LOWER LEFT (303 FEED) 3 A AUGER, LOWER LEFT (303 HAY) 6 1/" TUBE FLIGHTING AND KICKERS 4 A AUGER, UPPER LEFT (03 FEED) AR FLT, RIGHT HAND (FEED) 4 A AUGER, UPPER LEFT (03 HAY) AR FLT, LEFT HAND (FEED) 4 A AUGER, UPPER LEFT (53 FEED) AR FLT, RIGHT HAND (HAY) 4 A AUGER, UPPER LEFT (53 HAY) AR FLT, LEFT HAND (HAY) 4 A AUGER, UPPER LEFT (303 FEED) AR KICKER, STANDARD 4 A AUGER, UPPER LEFT (303 HAY) AR KICKER, ANGLE 11 A16048 STUB SHAFT, UPPER FRONT AR KICKER, SHARK FIN 1 A16049 STUB SHAFT, LOWER FRONT AR KICKER, STANDARD ND PART NOTE: AR - AS REQUIRED 9

10 REAR DRIVE REAR DRIVE SET COLLAR CHAIN W/CONNECTOR (03,53) A TENSIONER ARM ASS'Y CHAIN W/CONNECTOR (303) EYE BOLT CHAIN W/CONNECTOR & OFFSET CHAIN 3 LINKS GREASE ZERK SPRING WASHER, FLAT 6 A SPROCKET W/ BEARING FITTING, COMPRESSION 7 A1810 OILER ASS'Y TUBING, ALUMINUM 16' CHAIN 6 LINKS NUT, HEX 9 A13375 SPROCKET W/ BEARING AR CONNECTOR LINK 1 A SLIDE TENSIONER ASS'Y AR OFFSET LINK CHAIN 8 LINKS AR CONNECTOR LINK BEARING, NYLON AR OFFSET LINK CHAIN LINKS FITTING, COMPRESSION CHAIN W/CONNECTOR 8 A TENSIONER GUIDE ASSEMBLY NOTE: AR - AS REQUIRED 10

11 REAR DRIVE 1 A FLANGED STUB SHAFT ASS'Y SPROCKET, 60 TOOTH SCREW, HEX HD SPROCKET, 3 TOOTH BEARING SPROCKET, 14 TOOTH WASHER, LOCK KEY, SQUARE NUT, HEX SPROCKET, 3 TOOTH SPROCKET, 36 TOOTH KEY, SQUARE KEY, SQUARE 11

12 DISCHARGE 03, 53, 303 1

13 DISCHARGE *1 A DIS. BOTTOM ASS'Y, STD. (3") SPROCKET *1 A DIS. BOTTOM ASS'Y, EXT. (44") KEY FITTING, COMPRESSION CHAIN " TUBING, GREASE KEY *4 A AUGER, STANDARD (3") CHAIN *4 A AUGER, EXTENDED (44") SPROCKET FITTING, 90 DEG KEY, WOODRUFF COUPLING * AR SET SCREW HOSE MOUNT CLAMP SPROCKET SCREW, HEX HD CAP SCREW BEARING CAP WASHER, FLAT BEARING MOTOR, HYDRAULIC 11 A BEARING HOUSING * AR FLIGHTING, AUGER GREASE ZERK PLATE, HANGER (SHORT) *13 NSS 3 BEARING COLLAR PLATE, HANGER (EXTENDED) WASHER, LOCK 30 A1585 DISCHARGE PIN NUT NOTE: *1,*4 - WHEN ORDERING A NEW DISCHARGE, AUGER, AUGER FLIGHTING, BOTTOM, OR LINER MEASURE LENGTH. MEASUREMENTS ARE TAKEN FROM UNDER ANY AUGER FROM THE BACK PLATE TO THE END (WHERE CHUTE BEGINS). (SEE PAGE 14 FOR VISUAL REFERENCE.) *13 - NSS - NOT SOLD SEPARATELY *3,8 - AR - AS REQUIRED 13

14 DISCHARGE ASSEMBLY 14

15 DISCHARGE 1 A DOOR W/O CYL CLEVIS NUT 30086C 5 NUT, HEX SCREW, SQR HD SET WASHER, LOCK *17 A16733 AR DISCHARGE ASS Y, STD (3 ) CLEVIS, CYLINDER MOUNT *17 A16735 AR DISCHARGE ASS Y, EXT (44 ) SCREW 18 A1585 DISCHARGE PIN * AR MAGNET CLIP, HAIR PIN * AR PLATE, USE W/O MAGNET SCREW SCREW, HEX HD SCREW, HEX HD WASHER, LOCK WASHER, FLAT PIN, CHUTE HINGE SCREW NUT CLEVIS, DOOR CYL. MOUNT 11 A CHUTE, W/ MAGNET GUARD SCREW, HEX HD 1 A15730 AR MAGNET GUARD CYLINDER MOUNT TUBE PIN, ¾ DIAMETER BUSHING, SHORT WASHER, LOCK BUSHING, LONG NOTE: *6 - USE EITHER PART NUMBER OR *17 - WHEN ORDERING A NEW DISCHARGE, HANGER PLATE, AUGER, AUGER FLIGHTING, BOTTOM, OR LINER, MEASURE THE DISCHARGE LENGTH. MEASUREMENTS ARE TAKEN FROM UNDER EITHER AUGER FROM THE BACK PLATE TO THE END (WHERE CHUTE BEGINS). 15

16 TRAILER HYDRAULICS TRAILER HYDRAULICS SCREW * HOSE ASS'Y, 18" STD. DISCHARGE WASHER, FLAT *1 A HOSE ASS'Y, 31" EXT. DISCHARGE CHAIN, 3 LINKS * HOSE ASSEMBLY, 11 FT WASHER, LOCK ADAPTER, REDUCER NUT TEE DOUBLE HOSE CLAMP TEE SPRING CHECK VALVE CHAIN, 7 LINKS ADAPTER HOSE CLAMP ELBOW HOSE CLAMP * HOSE ASS'Y, 13" STD. DISCHARGE ELBOW *9 A168 1 HOSE ASS'Y, 9" EXT. DISCHARGE * HOSE ASSEMBLY, 16.5 FT ADAPTER * HOSE ASSEMBLY, 18 FT ELBOW WASHER, FLAT ELBOW WASHER, LOCK 33 A CYLINDER, DISCHARGE DOOR SCREW 34 A CYLINDER, DROP CHUTE MOTOR, HYDRAULIC NOTE: * MEASURE THE LENGTH OF EACH HOSE BEFORE ORDERING. 16

17 ELECTRIC CONTROL HYDRAULICS ELECTRIC CONTROL HYDRAULICS VALVE, ASSEMBLY * HOSE ASS'Y, 18" LG STD DISCHRG * HOSE ASS'Y, 11FT. W/90 DEG. FIT. *14 A HOSE ASS'Y, 31" LG EXT DISCHRG * HOSE ASS'Y, 11 FT VALVE, CHECK * HOSE ASS'Y, 6 FT. W/90 DEG. FIT. * HOSE ASS'Y, 13" LG STD DISCHRG * HOSE ASS'Y, 8 FT. W/90 DEG. FIT. *18 A168 1 HOSE ASS'Y, 9" LG EXT DISCHRG * HOSE ASS'Y, 10 FT. W/90 DEG. FIT ADAPTER ELBOW TEE, 1 FEMALE - MALE 8 A CYLINDER ASSEMBLY, DOOR ELBOW SWITCH, TOGGLE MOTOR, HYDRAULIC SWITCH, TOGGLE POLE MOMEN ADAPTER 11 A ELECTRIC CONTROL ASSEMBLY ELBOW TEE, ALL MALE ELBOW ADAPTER, REDUCER 6 A CYLINDER ASS'Y, DROP CHUTE NOTE: * MEASURE THE LENGTH OF EACH HOSE BEFORE ORDERING. 17

18 INTEGRAL HYDRAULICS INTEGRAL HYDRAULICS NIPPLE HOSE ASSEMBLY, 7" LG FILTER AND ADAPTER ELBOW, 90 DEG HOSE BARB 0 A CYLINDER ASS'Y, DIS. DOOR HOSE CLAMP ELBOW, 90 DEG HYDRAULIC FILTER HOSE ASSEMBLY, 9" LG. 6 A HYDRAULIC RESERVOIR TEE HOSE, 7" LG CHECK VALVE STACK VALVE ADAPTER HOSE ASSEMBLY, 60" LG ELBOW, 90 DEG ELBOW, 90 DEG MOTOR, HYDRAULIC PUMP ADAPTER ELBOW, 90 DEG. * HOSE ASS'Y, 13" STD. DISCHARGE HOSE BARB *30 A168 1 HOSE ASS'Y, 9" EXT. DISCHARGE HOSE, 50" LG. 33 A CYLINDER ASS'Y, DROP CHUTE HOSE BARB * HOSE ASS'Y, 18" STD. DISCHARGE TANK SCREEN *34 A HOSE ASS'Y, 31" EXT. DISCHARGE ADAPTER NOTE: *30,34 - MEASURE THE LENGTH OF EACH HOSE BEFORE ORDERING. 18

19 DROP CHUTE CYLINDER DROP CHUTE CYLINDER A CHUTE CYLINDER ASSEMBLY 8 *NSS BACK-UP RING 1 A95 1 PISTON SEAL KIT 9 *NSS 1 O-RING A GLAND NUT SEAL KIT GLAND NUT 4 A CYLINDER BODY 11 *NSS 1 O-RING NUT 1 *NSS 1 BACK-UP RING PISTON 13 *NSS 1 WIPER 7 *NSS O-RING 14 A CYLINDER SHAFT ASSEMBLY NOTE: *NSS - NOT SOLD SEPARATELY 19

20 DISCHARGE DOOR CYLINDER DISCHARGE DOOR CYLINDER A CYLINDER ASS'Y, DISCHARGE DOOR 9 *NSS 1 PISTON ROD 1 A95 1 PISTON SEAL KIT 10 *NSS 1 O-RING A GLAND NUT SEAL KIT 11 *NSS 1 RETAINING RING 4 A CYLINDER BODY ASSEMBLY 1 *NSS 1 BUSHING NUT 13 *NSS 1 POLY SEAL PISTON 14 *NSS 1 WIPER BUSHING 7 *NSS O-RING 15 *NSS 1 WIPER RING 8 *NSS BACK-UP RING GLAND NUT NOTE: *NSS - NOT SOLD SEPARATELY 0

21 LINERS & HAY SHELVES LINERS & HAY SHELVES *1 A9665 END LINER STAINLESS STEEL BOTTOM SS, 6 FT. LG. (303) *1 A9737 END LINER MILD STEEL BOTTOM MS, 6 FT. LG. (303) SIDE LINER SS, 4 FT. LG. (03) * DISCHARGE LINER 3" SS SIDE LINER MS, 4 FT. LG. (03) * DISCHARGE LINER 3" MILD 9501 SIDE LINER SS, 4 FT. LG. (53) * DISCHARGE LINER 44" SS 9503 SIDE LINER SS, 6 FT. LG. (53) * DISCHARGE LINER 44" MILD 950 SIDE LINER MS, 4 FT. LG. (53) END LINER BOTTOM SS 9504 SIDE LINER MS, 6 FT. LG. (53) END LINER BOTTOM MILD 9503 SIDE LINER SS, 6 FT. LG. (303) END LINER MID SS 9504 SIDE LINER MS, 6 FT. LG. (303) END LINER MID MILD BOTTOM SS, 4 FT. LG. (03) END LINER TOP SS BOTTOM MS, 4 FT. LG. (03) END LINER TOP MILD BOTTOM SS, 4 FT. LG. (53) 8 A HAY SHELF ASS'Y, 6 FT (03, 53, 303) BOTTOM SS, 6 FT. LG. (53) 9 A HAY SHELF ASS'Y, 4 FT (303) BOTTOM MS, 4 FT. LG. (53) 10 A HAY SHELF ASS'Y, FT (53) BOTTOM MS, 6 FT. LG. (53) NOTE: *1,*4 - WHEN ORDERING A NEW DISCHARGE, AUGER, AUGER FLIGHTING, BOTTOM, OR LINER MEASURE LENGTH. MEASUREMENTS ARE TAKEN FROM UNDER ANY AUGER FROM THE BACK PLATE TO THE END (WHERE CHUTE BEGINS). 1

22 LINERS LINERS *1 A9665 END LINER STAINLESS STEEL BOTTOM MS, 4 FT. LG. (53) *1 A9737 END LINER MILD STEEL BOTTOM MS, 6 FT. LG. (53) SIDE LINER SS, 4 FT. LG. (03) BOTTOM SS, 6 FT. LG. (303) SIDE LINER MS, 4 FT. LG. (03) BOTTOM MS, 6 FT. LG. (303) 9501 SIDE LINER SS, 4 FT. LG. (53) * DISCHARGE LINER 3 SS 9503 SIDE LINER SS, 6 FT. LG. (53) * DISCHARGE LINER 3 MILD 950 SIDE LINER MS, 4 FT. LG. (53) * DISCHARGE LINER 44 SS 9504 SIDE LINER MS, 6 FT. LG. (53) * DISCHARGE LINER 44 MILD 9503 SIDE LINER SS, 6 FT. LG. (303) END LINER BOTTOM SS 9504 SIDE LINER MS, 6 FT. LG. (303) END LINER BOTTOM MILD BOTTOM SS, 4 FT. LG. (03) END LINER MID SS BOTTOM MS, 4 FT. LG. (03) END LINER MID MILD BOTTOM SS, 4 FT. LG. (53) END LINER TOP SS BOTTOM SS, 6 FT. LG. (53) END LINER TOP MILD

23 DOOR MARKER - TRAILER DOOR MARKER - TRAILER 1 A POINTER ASSEMBLY SPACER 1 A POINTER ASS'Y (303 TRUCK) WASHER, FLAT SHAFT COLLAR C SCREW 3 A ARM ASSEMBLY DECAL, DOOR GAUGE NUT DECAL, DOOR GAUGE (303 TRUCK) WASHER, LOCK ROD MOUNT LINKAGE BAR DOOR MARKER TAB 3

24 REAR OIL BATH REAR OIL BATH SCREW, HEX HD CAP LATCH NUT, LOCK BAR, STRUT MOUNT BRACE WASHER, FLAT OIL BATH ROOF NUT, HEX OIL BATH TOP CLOSURE NUT OIL BATH SIDE, RIGHT WASHER, LOCK OIL BATH SIDE, LEFT WASHER, FLAT OIL BATH BOTTOM CLOSURE SCREW HINGE SCREW STRUT, GAS CHARGED SUPPORT * ' SEAL, FLEXIBLE DOOR 1/4 3 A STRUT MOUNT ASSEMBLY * ' SEAL, FLEXIBLE DOOR 1/ ANGLE, STRUT MOUNT OIL BATH DOOR CHANNEL, FORMED DOOR BRACE HANDLE, OIL BATH DOOR NOTE: *AR - AS REQUIRED *10 - TO BE USED ON TOP OF DOOR OPENING. *11 - TO BE USED ON SIDES AND BOTTOM OF DOOR OPENING. 4

25 MIXER DECALS 5

26 MIXER DECALS DECAL DOOR MARKER (TRUCK) DECAL ** A HAYMOGENIZER DECAL KIT DECAL ** A DECAL KIT HARSH DECAL (SIDE, REAR) ** A DECAL KIT ' RED STRIPE SIDE, 03 ** A DECAL KIT (TRAILER) ' RED STRIPE SIDE, 53 ** A DECAL KIT (TRUCK) ' RED STRIPE SIDE, 303 ** A SAFETY DECAL KIT NO LIFT DECAL STATIONARY DECAL DANGER, ROTATING AUGERS * DANGER DO NOT ENTER OIL BATH MAINTENANCE * DO NOT OPERATE W/O SHIELD DANGER, DRIVE LINE * SLOW MOVING VEHICLE DANGER, 540 RPM REFLECTOR, ORANGE DOOR MARKER (TRAILER) REFLECTOR, RED MAINTENANCE GEAR BOX SPROCKET ROTATION CAUTION, WELDING DECAL, SERIES THREE HAYMOGENIZER LOADING * DECAL, OFF ROAD USE HAYMOGENIZER * DECAL, TUB GUARD NOTE: *1,*9 - INSTALL NEXT TO LADDER. *,*3,*8 - DECALS ARE USED ON TRAILER MODEL ONLY. ** DECALS INCLUDED IN DECAL KITS ARE EQUAL TO DECALS ATTACHED TO MIXER AT TIME OF SHIPMENT. DECALS NOT AVAILABLE SEPARATELY...PURCHASE BY KIT ONLY HARSH ENCOURAGES THE REPLACEMENT OF ALL SAFETY DECALS WHEN THEY BECOME UNREADABLE, DAMAGED, OR IF THE UNIT IS REPAINTED. IN ORDER TO ASSURE MIXERS ARE COMPLETELY REDECALED WITH ALL THE NECESSARY SAFETY DECALS, THEY ARE INCLUDED IN THE TRUCK AND TRAILER DECAL KITS. IF YOU DO NOT DESIRE TO PURCHASE THE COMPLETE MIXER DECAL KIT, YOU CAN PURCHASE ONLY THE SAFETY DECAL KIT WHICH WILL PROVIDE YOU WITH THE SAFETY AND OPERATION DECALS ONLY. 6

27 TUB GUARD TUB GUARD * A TUB GUARD ASSEMBLY (03) SCREW, HEX HD CAP (53) * A TUB GUARD ASSEMBLY (53) SCREW, HEX HD CAP (303) * A TUB GUARD ASSEMBLY (303) NUT, HEX NY-LOCK (03) PIPE, TUB GUARD 96" LG. (03) NUT, HEX NY-LOCK (53) PIPE, TUB GUARD 10" LG. (53) NUT, HEX NY-LOCK (303) PIPE, TUB GUARD 144" LG. (303) WASHER, FLAT (03) PIPE, TUB GUARD 76" LG. (03) WASHER, FLAT (53) PIPE, TUB GUARD 76" LG. (53) WASHER, FLAT (303) PIPE, TUB GUARD 76" LG. (303) PIPE, GUARD SPACER 3/4 LG SCREW, HEX HD CAP (03) * DECAL, TUB GUARD NOTE: * TUB GUARD ASSEMBLIES INCLUDE ALL PARTS SHOWN. *7 INSTALL NEXT TO LADDER. 7

28 STATIONARY PARTS STATIONARY PARTS 1 A179 1 HAND WHEEL ASSEMBLY BUSHING, 1 1/8 ID (03,53) SCREW BUSHING, 1 3/8 ID (03,53) WASHER, LOCK BUSHING, 1 3/8 ID (303) NUT BUSHING, 1 5/8 ID (303) HANDLE, DOOR LOCK SHEAVE (03,53) 6 A DOOR LOCK ASSEMBLY SHEAVE (303) SPROCKET PLANETARY REDUCER 1: KEY 1 A INPUT ADAPTER ASSEMBLY SHAFT, DOOR OPENER KEY SCREW CHAIN COUPLING HALF BEARING CHAIN (FOR COUPLING) 14 A DISCHARGE DOOR ASS'Y COVER SHEAVE (03,53) BEARING, PILLOW BLOCK SHEAVE (303) SCREW BUSHING (03,53) WASHER, LOCK BUSHING (303) NUT BELT, V (03,53) SHAFT, DRIVE BELT, V (303) C 1 BEARING, TWO BOLT WASHER, FLAT NOTE: THE ABOVE IS THE STANDARD SET UP. MANY TIMES THE DRIVE COMPONENTS ARE SPECIAL ORDERED OR MODIFIED IN THE FIELD. THEREFORE, YOU MUST VERIFY BELTS, SHEAVES, AND BUSHING SPECIFICATIONS BEFORE ORDERING. 8

29 REV LET DESCRIPTION OF CHANGE ECO No REV REVDESC ECONO ( ITEM 16) (10.50) (3) HOLES THIS SIDE (ITEM 16) INSIDE FRONT SHEET TO CENTERLINE PEDESTAL C AD D R AW IN G - - D O N O T R E VIS E M AN U ALLY R E P O R T E R R O R S TO E N G IN E E R IN G D E P AR TM E N T QTY ITEM PART NO DESCRIPTION MATL SIZE UNIT MATL NO MATERIAL DESCRIPTION CUSTOMER RELEASE ECO# Unless Otherwise Specified: TITLE STATIONARY MIXER 03 & 53 SIZE C DRAWING NO COMP NO A7391S 7000/7400 REV NR FINAL ASSY 03, 53 SHEET OF SCALE: 1/4 DRAWN BY: SJC DATE: 4/18/05 All Dim ensions In Inches All Machine Surfaces 15 Break All Sharp Corners.010-Max. Tolerances: Dec. XX±.03 XXX±.005 Frac. ±1/16" Angles ± 1 CHECKED BY: APPROVED BY: PO BOX 7 DATE: DATE: EATON, CO HII#1060

30 TI TLE SI ZE DRAWI NG NO COMP NO 600 OAK AVE. EATON, CO CHECKED BY: DATE: OF DRAWN BY: DATE: APPROVED BY: DATE: Unl ess Otherwi se Speci fi ed: Al l Di mensi ons I n I nches Al l Machi ne Surfaces 15 Break Al l Sharp Corners Max. Tol erances: Dec. XX XXX Frac. + 1/16" Angl es+ 1 HI I #1 058 REV LET DESCRI PTI ON OF CHANGE ECO NO D REVISED AND REDRAWN REF SCALE: 1/ INSIDE FRONT SHEET 7.00 TO CENTERLINE PEDESTAL DETAIL "C" SEE SHEET FOR DIMENSIONS X REF DETAIL "C" A A B SECTION A - A ROTATED 90 CCW SCALE: 1/ X 1 3 X SECTION B - B ROTATED 90 CCW SCALE: 1/ NOTE: BELT DRIVE 68 INSTALL ITEMS 64, 67 & 69 PRIOR TO SHIPPING ITEMS 65, 66 & 68 ARE TO BE SHIPPED LOOSE PLACE (1) DEE RING ON INSIDE OF BOTH MIXER STANDS PLACE (1) DEE RINGS EQUALLY SPACED ON RIGHT SIDE OF MIXER UNDER 3 X 5 RAIL TUBE DRIVELINE GUARD, 7 1/ X 9 X HEX HEAD SCREW, 1/4-0 X 3/ DOOR FILLER (SIDES) 4 59 A16614 WEIGH BAR SPACER ASSY HEX HEAD SCREW, 3/8-16 X TRUSS HEAD SCREW, 5/16-18 X 3/4 B SHEAVE, B BELT 3.75 O.D. FOR SF BUSHING ALT BUSHING, SF 1 3/8 BORE BUSHING, SF 1 5/8 BORE BUSHING, SF 1 1/4 BORE HEX NUT, 1/ LOCK WASHER, 1/ FLAT WASHER, 1" SHIELD MOUNT ANGLE, X X SHIELD MOUNT ANGLE, X X 1 1/ HEX HEAD SCREW, 3/8-16 X 1 1/ HEX NUT, 3/ LOCK WASHER, 3/ FLAT WASHER, 3/ CARRIAGE HEAD SCREW, 3/8-16 X 1 1/ BEARING, HOLE FLANGE - Ø1" BEARING MOUNT PLATE 1/4 X 5 X 5 1/ 1 34 A17119 DISCHARGE DOOR 00'S STATIONARY BEARING MOUNT ANGLE DRIVELINE HANGER PLATE C HEX NUT, 1/ HINGE PIN, Ø1 X 14 1/ 1 17 A16707 MOTOR MOUNT ASSY (7.5-5 H.P.) 1 16 A1577 MOTOR MOUNT HANGER ASSY FLAT WASHER, 5/ HEX NUT, 5/ LOCK WASHER, 5/ SPACER C HEX HEAD SCREW, 5/16-18 X 1 1/ A1757 BELT GUARD ASSY - REAR 1 9 A1755 BELT GUARD ASSY - FRONT BEARING, PILLOW BLOCK, Ø1 1/ BELT DRIVE BEARING MOUNT PLATE BEARING MOUNT PLATE HEX LOCK NUT, 3/ HEX HEAD SCREW, 3/8-16 X 3 1/ 4 3 A15685 SCALE MOUNT TO TUB ASS'Y A1570 STATIONARY MIXER STAND ASS'Y 35" 1 1 A7653 TUB GROUP CAD DRAWI NG- - DO NOT REVI SE MANUALLY REPORT ERRORS TO ENGI NEERI NG DEPARTMENT DEE RING DISCHARGE CHUTE SIDE (LEFT) FLAT WASHER, 1/ QTY I TEM PART NO DESCRI PTI ON CARRIAGE BOLT, 1/-13 X 1 1/ DISCHARGE CHUTE SIDE (RIGHT) C BEARING, BOLT FLANGE, Ø1 1/4 MATLSI ZE UNI T MATL NO MATERI AL DESCRI PTI ON BEARING MOUNT PLATE 1/4 X 5 X DISCHARGE MAGNET DRIVE SHAFT, Ø 1 1/4 X 6 CUSTOMER RELEASE ECO# REF 75 A194 DOOR GUIDE ASS'Y GEAR BOX, PLANETARY - ED045 1: DOOR FILLER (TOP ANGLE) FORMED DRIVELINE GUARD ROLL PIN, Ø1/8 X 1" 1 70 A1840 TUB GUARD ASSY DISCHARGE CHUTE BOTTOM 1 5 A179 HAND WHEEL ASSY, Ø3 1/ OD WHEEL LOCK PLATE HEX HEAD SCREW, 5/16-18 X 1/ A1785 DOOR LOCK HANDLE W/ PIN DOOR LOCK MOUNT LOCK WASHER, 1/ HEX HEAD SCREW, 1/-13 X 1 1/ 1 5 A15707 INPUT ADAPTER ASSY 1 4 A19804 DRIVE SHAFT ASSY LOCK COLLAR, Ø1" ID HEX NUT, 3/8-16 STATIONARY MIXER 303 A740 D 7000/7400 REV D FI NAL ASSY 303 SHEET SCALE: 1 1/16 SJC 4/18/ KEY, 1/ X KEY, 1/4 X 1 1/ EYE BOLT, 3/8-16 X "B" BELT, B SPROCKET, H60B13 1" BORE HINGE PIN, Ø1 X 10 1/ SHEAVE, B BELT O.D. FOR SF BUSHING WHEEL SHAFT, Ø1" X A15734 BELT TENSIONER ASSY SEE 7391 FOR 03 & 53

31 REV LET DESCRIPTION OF CHANGE ECO No REV REVDESC ECONO ( ITEM 16) (10.50) (3) HOLES THIS SIDE (ITEM 16) INSIDE FRONT SHEET TO CENTERLINE PEDESTAL C AD D R AW IN G - - D O N O T R E VIS E M AN U ALLY R E P O R T E R R O R S TO E N G IN E E R IN G D E P AR TM E N T QTY ITEM PART NO DESCRIPTION MATL SIZE UNIT MATL NO MATERIAL DESCRIPTION CUSTOMER RELEASE ECO# Unless Otherwise Specified: TITLE STATIONARY MIXER 03 & 53 FINAL ASSY 03, 53 All Dimensions In Inches All Machine Surfaces 15 Break All Sharp Corners.010-Max. Tolerances: SIZE C DRAWING NO COMP NO A7391S 7000/7400 REV NR SHEET OF SCALE: 1/4 DRAWN BY: SJC DATE: 4/18/05 Dec. XX±.03 XXX±.005 Frac. ±1/16" Angles ± 1 CHECKED BY: APPROVED BY: PO BOX 7 DATE: DATE: EATON, CO HII#1060

32 SEE 740 FOR 303 SIZE DRAWING NO COMP NO REV 600 OAK AVE. EATON, CO SCALE: CHECKED BY: DATE: OF 1/8 DRAWN BY: DATE: APPROVED BY: DATE: Tolerances: Dec. XX+.0 3 XXX Frac. + 1/16" Angles + 1 HII#1058 TITLE SIZE DRAWING NO COMP NO 600 OAK AVE. EATON, CO CHECKED BY: DATE: OF DRAWN BY: DATE: APPROVED BY: DATE: Unless Otherwise Specified: All Dim ensions In Inches All Machine Surfaces 15 Break All Sharp Corners.010- M ax. Tolerances: XXX+.005 Frac. + 1/16" Angles + 1 HII# BEARING, PILLOW BLOCK 1 1/ SCREW, TRUSS HD. 5/16-18x3/ MAGNET 18" SHEAVE, "3V" BELT O.D BUSHING, SH 1 1/8 BORE BUSHING, SH 1 3/8 BORE COVER-40G CHAIN C CHAIN COUPLING HALF 1 1/4 SETS D A /7391 G SHEET1 1 BLA 8/19/ BOTTOM, DISCHARGE CHUTE BUSHING, SK 1 1/4 BORE KEY, 5/16x1 1/ SIDE, DISCHARGE CHUTE (RIGHT) SIDE, DISCHARGE CHUTE (LEFT) WASHER, FLAT 5/ COTTER PIN 1/8x SHAFT, DRIVE 1 1/4 DIA.x40 1/ COLLAR, SET SCREW 1" REV LET DESCRIPTION OF CHANGE ECO NO D REVISED AND REDRAWN INSIDE FRONT SHEET 7.00 TO CENTERLINE PEDESTAL DETAIL "C" SCALE: 1/ SEE SHEET FOR DIMENSIONS X DETAIL "C" A B REF A SECTION A - A ROTATED 90 CCW SCALE: 1/ X 1 3 X SECTION B - B ROTATED 90 CCW SCALE: 1/ NOTE: BELT DRIVE INSTALL ITEMS 64, 67 & 69 PRIOR TO SHIPPING ITEMS 65, 66 & 68 ARE TO BE SHIPPED LOOSE PLACE (1) DEE RING ON INSIDE OF BOTH MIXER STANDS PLACE (1) DEE RINGS EQUALLY SPACED ON RIGHT SIDE OF MIXER UNDER 3 X 5 RAIL TUBE DRIVELINE GUARD, 7 1/ X 9 X DEE RING CARRIAGE BOLT, 1/-13 X 1 1/ SHEAVE, "3V" BELT 3.35 O.D. ALT BUSHING, SH 1 1/8 BORE BUSHING, SH 1 3/8 BORE BUSHING, SK 1 1/4 BORE HEX NUT, 1/ LOCK WASHER, 1/ HEX HEAD SCREW, 1/4-0 X 3/ DOOR FILLER (SIDES) 4 59 A16614 WEIGH BAR SPACER ASSY HEX HEAD SCREW, 3/8-16 X DISCHARGE CHUTE SIDE (LEFT) DISCHARGE CHUTE SIDE (RIGHT) B TRUSS HEAD SCREW, 5/16-18 X 3/ FLAT WASHER, 1" SHIELD MOUNT ANGLE, X X SHIELD MOUNT ANGLE, X X 1 1/ HEX HEAD SCREW, 3/8-16 X 1 1/ HEX NUT, 3/ LOCK WASHER, 3/ FLAT WASHER, 3/ CARRIAGE HEAD SCREW, 3/8-16 X 1 1/ BEARING, HOLE FLANGE - Ø1" BEARING MOUNT PLATE 1/4 X 5 X 5 1/ 1 34 A17119 DISCHARGE DOOR 00'S STATIONARY BEARING MOUNT ANGLE DRIVELINE HANGER PLATE C HEX NUT, 1/ FLAT WASHER, 1/ C BEARING, BOLT FLANGE, Ø1 1/4 MATL HINGE PIN, Ø1 X 14 1/ 1 17 A16707 MOTOR MOUNT ASSY (7.5-5 H.P.) 1 16 A1577 MOTOR MOUNT HANGER ASSY FLAT WASHER, 5/ HEX NUT, 5/ LOCK WASHER, 5/ SPACER C HEX HEAD SCREW, 5/16-18 X 1 1/ A1757 BELT GUARD ASSY - REAR 1 9 A1755 BELT GUARD ASSY - FRONT BEARING, PILLOW BLOCK, Ø1 1/ BELT DRIVE BEARING MOUNT PLATE BEARING MOUNT PLATE HEX LOCK NUT, 3/ HEX HEAD SCREW, 3/8-16 X 3 1/ 4 3 A15685 SCALE MOUNT TO TUB ASS'Y A1570 STATIONARY MIXER STAND ASS'Y 35" 1 1 A765 TUB GROUP A7651 TUB GROUP - 03 QTY SIZE ITEM UNIT PART NO MATL NO DESCRIPTION MATERIAL DESCRIPTION C AD D R AW IN G - - D O N O T R EVIS E M AN U ALLY R EP O R T ER R O R S TO EN G IN EER IN G D EP AR TM EN T BEARING MOUNT PLATE 1/4 X 5 X DISCHARGE MAGNET DRIVE SHAFT, Ø 1 1/4 X 6 CUSTOMER RELEASE ECO# 75 A194 DOOR GUIDE ASS'Y GEAR BOX, PLANETARY - ED045 1: DOOR FILLER (TOP ANGLE) FORMED DRIVELINE GUARD ROLL PIN, Ø1/8 X 1" 1 70 A1759 TUB GUARD ASSY DISCHARGE CHUTE BOTTOM 1 5 A179 HAND WHEEL ASSY, Ø3 1/ OD WHEEL LOCK PLATE HEX HEAD SCREW, 5/16-18 X 1/ A1785 DOOR LOCK HANDLE W/ PIN DOOR LOCK MOUNT LOCK WASHER, 1/ HEX HEAD SCREW, 1/-13 X 1 1/ 1 5 A15707 INPUT ADAPTER ASSY 1 4 A19804 DRIVE SHAFT ASSY LOCK COLLAR, Ø1" ID HEX NUT, 3/8-16 STATIONARY MIXER 03 & 53 A7391 D 7000/7300 REV D FINAL ASSY 03, 53 SHEET SCALE: 1 1/16 SJC 4/18/05 Dec. XX KEY, 1/ X KEY, 1/4 X 1 1/ EYE BOLT, 3/8-16 X V-BELT, 3V X 60" LONG SPROCKET, H60B13 1" BORE HINGE PIN, Ø1 X 10 1/ SHEAVE, "3V" BELT O.D WHEEL SHAFT, Ø1" X A15734 BELT TENSIONER ASSY

33 INDEX GROUPS PAGE NUMBER Auger, Assembly...8, 9 Auger, Discharge...1, 13 Axle, Trailer...5 Bumper...5 Bearing, Auger (front & rear)...11 Bearings, Discharge...1, 13 Chains, Discharge...1, 13 Chains, Rear Drive...10 Chain Tensioners...10 Cylinder, Discharge Chute...19 Cylinder, Discharge Door...0 Decals...4, 5 Discharge Assembly...1, 15 Door, Discharge...14, 15 Door Marker, Trailer... Door, Rear Oil Bath...3 Drive Assembly, Rear...10, 11 Driveline, Trailer...6, 7 Discharge Chute...14, 15 Fender, Trailer...5 Flighting, Auger...8, 9 Flighting, Discharge Auger...1, 13 Frame Assembly, Trailer...5 Gearbox, Planetary...6 Hitch, Trailer...5 Hydraulic Motor, Discharge...1, 13, 16 Hydraulics, Trailer...16 Hydraulics, Electric Control...17 Hydraulics, Integral...18 Jack, Trailer...5 Liners...1 Magnet, Discharge Chute...14, 15 Mixer Orientation...4 PTO Drive Shaft...6, 7 Rear Oil Bath...3 Rims, Trailer...5 Serial Number Code...4 Sprockets, Discharge...1,13 Sprockets, Rear Drive...10, 11 Stationary Parts...7 Stub Shafts, Auger...8, 8, 11 Tires, Trailer...5 Tub Guard...6 Tubes, Trailer...5 9