MODELS 470, 570, 670, 770 Corner Auger GRAIN CART (For Model 970 Information, Refer to Manual #250541)

Transcription

1 OPERATOR S MANUAL PARTS CATALOG MODELS 470, 570, 670, 770 Corner Auger GRAIN CART (For Model 970 Information, Refer to Manual #250541) PART NO

2 Late Model 70 Series Early Model 70 Series (Chain Cover) MODEL 470, 570, 670, 770 PARTS \

3 MODEL 470, 570, 670, 770 PARTS Item Description Part No. Previous Current Notes 1 Scale Hitch B Single Tang. 2 Htich Bar, 2 1/2 B Complet PTO See Pages 5, 7, 9 4 PTO Front Half Part of Item 4 5 Window B Window Molding B Not Applicable 8 Complete Driveshaft B See Page 11 9 U-Joint, 3/4" B Upper Auger Weldment B Auger Pipe Length 147" (2nd year - '89 and Up) Auger Pipe Length 129" (1st year - '88) 13 Upper Auger Housing B Tube Length 149" Tube Length 131" 14 Stub Shaft, 1 1/2" B Flange Bearing, 1 1/2 B Capscrew, 1/2 x 4 1/2 B Lockwasher, 1/ Nut, 1/ Auger Spring B Decals B See Page Amber Lens B Red Lens B Refl ector w/bulb Wheel, 16 x 26 B Wheel, 20 x 26 B Wheel, 21 x 32 B , 570, 670 Wheel, 21 x 32 B Wheel, 27 x , 570, 670 Wheel, 27 x 32 B Decal, Tire Pressure B Decal, Tighten Ft. Lbs. B Valve Stem B Plug Cylinder, 2 x 36" B Flow Control Door Cylinder, 2 x 42" B Flow Control Door 30 Hinge Pin B Hair Pin B Cylinder Pin, 1 x3 B Restrictor Adapter Qty 2 Cylinder, 2 1/2 x 14 (1 1/8" Rod) B Seal Kit # Seal Kit (Wire Gland Retainer) Cylinder, 2 1/2 x 14 (1" Rod) Seal Kit (Snap Ring Gland Retainer) 36 T-Bar Threaded B T-Bar Pin, 1 x 5 B Drive Dog, 1 7/8 ID B Uses Keystock No Longer Available - Use Part No.s Drive Dog, 1 3/4 ID CALL , & Brass Bushing, 1 7/8 B Verify size before ordering - Brass Bushing, 1 3/4 B /8" is the later version Capscrew, 3/8 x 1 1/ Lockwasher, 3/ Nut, 3/ (July 2014) 3

4 MODEL 470, 570, 670, 770 PARTS Item Description Part No. Previous Current Notes 41 Missile Shaft, 1 7/8 B Verify size before ordering - Missile Shaft, 1 3/4 B /8" is the later version 42 Lower Auger Weldment B Double Knuckle B Series - 1 1/2 Rd. Yoke Ends Series - One End 1 1/2 Rd., Double Knuckle B One End 1 3/8-21 Spline 44 Snap Ring B Bearing, Sealed - 1 9/16 B Canister Shaft, 1 1/2 x 10 1/2 B Stub Shaft B Thrust Bearing, 2" B Flange Bearing, 2" B Sprocket, 26T 2" Bore B Idler Sprocket, 11T B Chain, 39 Pitch 80 B w/connecting Link 53 Sprocket, 15T B Bearing Grease Cap Weldment Hanger Bracket Assembly - 1 7/8" Bore B 57 Jack B Jack Plate Canister Assembly B Steel Chute B Rubber Chute (used on early 70 Series) Spindle, 2 7/ , 570, Scale Spindle, 2 7/8 B , 570, 670 Spindle, 4 1/2" Scale Spindle, 3 3/4 B Spindle Bushing B Scale Only 62 Chain Cover See Page Drive Shaft See Page Stub Shaft See Page T-Bar Yoke End B Swivel Hitch - Clevis B Swivel Hitch - Single Swivel Hitch Bushing B Swivel Hitch Retainer B Scale Hitch Bushing B Wiring Harness B Wiring Harness - Auger B Electrical Coupler B Butt Connector, 14 GA. B Scale Power Cord B Scale Cab Extension Cord B Auger Light B Use Light Bracket Cylinder Arm B Rockshaft & Crank Assembly B Seal Ring Scale Only 89 Spring Adjustable Slide Idler Idler Kit Ladder Key, 3/8 x 3/8 x 1.45 Lg Used with Sprockets Model Year Length Upper Lower General Length Dia. RH/LH Flighting Flighting Comments All 147" " " LH Upper 129" " " LH Upper 4 (July 2014)

5 MODEL 470, 570, 670, 770 PTO ASSEMBLY WITH 2-PLATE CLUTCH 1 3/8" Splined Center Hub Item Description Part No. Previous Current Notes 1 Complete PTO /8-21 Spline 11 End Yoke B /8-21 Spline End Yoke B /4-20 Spline 12 Quick Disconnect Kit B Friction Clutch Complete Plate B " Long x 1" Diameter 21 Cross & Bearing Kit " Long x 1.375" Diameter " Long x 1.25" Diameter 22 Grease Zerk B Inboard Yoke, Tractor End B Spring Pin B Inner Profi le B Outer Profi le B Inboard Yoke, Cart End B Back Shield Cone B Screw B Bearing Ring B Transport Chain B Outer Shield Tube B Inner Shield Tube B Decal, Danger Shield B Decal, Danger Shield B

6 470,570,670,770 2-PLATE CLUTCH ITEM DESCRIPTION PREVIOUS CURRENT QTY. NOTES PART NO. PART NO. 1 Clutch Housing B Clutch Lining B Hub, 1 3/8"-21 Spline B Thrust Plate B Belleville Spring B Hex Nut, M8 Din 6330 B Quick Disc. Flange Kit B Incl. Items

7 MODEL 470, 570, 670, 770 PTO ASSEMBLY WITH 4-PLATE CLUTCH 1 3/8" Splined Center Hub ITEM DESCRIPTION PREVIOUS CURRENT NOTES PART NO. PART NO. 1 Complete PTO /8-21 Spline Complete PTO /4-20 Spline 11 End Yoke B /8-21 Spline End Yoke /4-20 Spline 12 Quick Disconnect Kit B Friction Clutch Complete Plate 21 Cross & Bearing Kit B Grease Zerk B Inboard Yoke, Tractor End B Spring Pin B Inner Profile B Outer Profile B Inboard Yoke, Cart End B Back Shield Cone B Screw B Bearing Ring B Safety Chain B Outer Shield Tube B Inner Shield Tube B Danger Decal, Shield B Danger Decal, Shield B

8 MODELS 470, 570, 670, PLATE CLUTCH Item Description Part No. Notes 1 Friction Clutch Complete /8-21 Spline 2 Retaining Ring Flanged Ring Lock Collar Compression Spring Back-Up Ring Hex Nut, M8 Din Belleville Spring Thrust Plate Drive Plate Clutch Lining Drive Plate Ball Hub, 1 3/8-21 Spline Clutch Housing Quick Disconnect Flange Kit Kit Items 2-6, (July 2014)

9 MODEL 470, 570, 670, 770 PTO ASSEMBLY WITH 2-PLATE CLUTCH 1 1/4 Keyed Clutch ITEM DESCRIPTION PREVIOUS CURRENT NOTES PART NO. PART NO. 1 Complete PTO /8-21 Spline 11 End Yoke B /8-21 Spline End Yoke /4-20 Spline 12 Quick Disconnect Kit B Friction Clutch Complete B Plate 21 Cross & Bearing Kit B Grease Zerk B Inboard Yoke, Tractor End B Spring Pin B Inner Profile B Outer Profile B Inboard Yoke, Cart End B Back Shield Cone B Screw B Bearing Ring B Safety Chain B Outer Shield Tube B Inner Shield Tube B Danger Decal, Shield B Danger Decal, Shield B

10 MODELS 470, 570, PLATE CLUTCH 1 1/4 Round Hub ITEM DESCRIPTION PREVIOUS CURRENT QTY. NOTES PART NO. PART NO. 1 Clutch Housing B Friction Disk B Hub, 1 1/4" RB, 5/16" Kwy B Thrust Plate B Belleville Spring B Hex Nut, M8 DIN6330 B

11 70 SERIES DRIVE SHAFT / STUB SHAFTS (July 2014) 11

12 MODELS 470, 570, 670, 770 DOUBLE KNUCKLE ASSEMBLY WALTERSCHEID 2500 ITEM DESCRIPTION PREVIOUS CURRENT QTY. NOTES PART NO. PART NO /2" Bore Yoke B Cross Kit w/snap Ring B Center Yoke B /8"-21 Spline Yoke B Complete Double Knuckle WALTERSCHEID 2400 ITEM DESCRIPTION PREVIOUS CURRENT QTY. NOTES PART NO. PART NO /2" Bore Yoke Cross Kit w/snap Ring Center Yoke /2" Bore Yoke Complete Double Knuckle A

13 MODELS 470, 570, 670, 770 CHAIN DRIVE COVER PARTS ITEM DESCRIPTION PREVIOUS CURRENT QTY. NOTES PART NO. PART NO. 1 Chain Cover B Late Model 2 Chain Cover Early Model 3 Chain Cover Seal B Per foot 4 Chain Redi Rod B Chain Cover Knob B

14 HUB - MODELS 470, 570, 670 ITEM Description Part No. Previous Current 1 Seal, 2 7/8" ID B Stub B Nut B Outer Cup, 4 1/4" OD B Outer Bearing Cone, 1 3/4" ID B Hub Cap B Cotter Key B Nut B Washer B Capscrew, 5/16 x 1/2 B Hub B Inner Cup, 4 5/8" OD B Inner Bearing Cone B Complete Hub Assembly B Notes \

15 HUB - MODEL 770 ITEM DESCRIPTION PREVIOUS CURRENT NOTES PART NO. PART NO. 1 Seal, Standard Unit Only Seal - Scale Unit Stud Nut Outer Cup Outer Bearing Cone Hub Cap Cotter Key Nut Washer Capscrew, 5/16 x 1/ Hub Inner cup Inner Bearing Cone Complete Hub Assy - Standard Complete Hub Assy - Scale Seal Changes

16 DECALS - 70 SERIES ITEM Description Part No. Notes 1 Decal, Brent By UM - Tri Colored Decal, Brent By UM - Black & Yellow Decal, Brent By UM - Black on White Decal, Decal, Decal, Decal, Decal, Warning to Avoid Injury Decal, Caution Do Not Play Decal, Important Flow Control Gate Decal, FEMA Decal, Flow Control - 3" x 38" Decal, Caution - To Avoid Injury Decal, Danger - Just for Kids Decal, Danger - Drive Shaft Entangle Decal, Danger - Electrical Lines Decal, Important - Double U-Joint Decal, Corner Auger Patented Decal, Stripes - Black & Yellow

17 BOTTOM PLATE OF AUGER MODELS 470,570,670,770 DRIVE SPROCKET KIT LOCATING JIG INDLER MOUNT BLOCK REMOVE OLD CHAIN COVER. TORCH OFF OLD IDLER ARM INSIDE OF THE CHAIN CASE. TORCH ALL OF THE OLD CHAIN COVER THAT IS WELDED TO THE BOTTOM PLATE OF THE AUGER. REMOVE THE CHAIN FROM THE DRIVE SPROCKETS. PLACE THE LOCATING JIG OVER THE HUBS OF THE SPROCKETS AS SHOWN ABOVE. LINE UP THE IDLER MOUNT BLOCK WITH THE JIG USING TWO BOLTS. WELD ON THE IDLER MOUNT BLOCK TO THE BOTTOM PLATE OF THE AUGER. REMOVE THE LOCATING JIG. IDLER ARM USE BOLT HERE USE REDI-ROD HERE INSTALL CHAIN AND IDLER, MAKING SURE TO USE THE REDI-ROD ON THE CORRECT HOLE OF THE IDLER MOUNT BLOCK. ON THE REDI-ROD USE A FLAT WASHER, LOCK WASHER AND HEX NUT TO SECURE THE IDLER ARM TO THE IDLER MOUNT BLOCK. A HEX NUT IS USED FOR A SPACER BETWEEN THE IDLER SPROCKET AND THE IDLER ARM. GREASE ZERK MUST COME THRU COVER HERE WELD ON CHAIN COVER SO THAT THERE IS CLEARANCE FOR THE GREASE ZERK TO COME THRU CHAIN COVER AND THERE IS NO GAPS IN THE CHAIN COVER WHEN THE BOLT ON SECTION IS INSTALLED. USE A FLAT WASHER, LOCK WASHER AND PLASTIC KNOB TO SECURE THE BOLT ON SECTION OF THE CHAIN COVER TO THE CART. BOLT ON SECTION WELD ON CHAIN COVER ITEM DESCRIPTION PART NO. QTY. Kit, Auger Chain Idler - Incl: Adjustable Slide Idler Chain Cover/Adjust Slide Redi-Rod, 1/2 UNC x Chain Roller, #80 x 39 Links Template Chain Idler Mount Sprocket, 11 Tooth ITEM DESCRIPTION PART NO. QTY. 9 Trim Lock Knob/Clamping Capscrew, 1/2-13 x 1 1/ Capscrew, 3/4-10 x Nut, 1/2-13 UNC Nut, 3/4-10 UNC Lockwasher, 1/ Flatwasher, 1/ Flatwasher, 3/

18 NOTES 18