Series AN05 to 40 RoHS

Transcription

1 Silencer Compact Resin Type/Male Thread N0 to 40 RoHS How to Order N 0 Body size Specifications Thread type M thread Nil R N NPT Thread connection port size pplicable model M M x 0.8 /8 /4 3/8 / N0 N0 N/ N30 N40 Fluid Max. operating pressure Note ) Noise reduction mbient and fluid temperature Compressed air 4psi (.0 MPa) 30 db() Note ) 4 to 40 F ( to 60ºC) Note 3) Note ) It indicates the inlet pressure for solenoid valve. Note ) The value may vary, depending on the pneumatic circuit or pressure that is exhausted from the solenoid valve. Note 3) The product can be used in temperatures 4 to 40 F ( 0 to 60 C) if there is no risk of water droplets forming and freezing. Refer to page for Precautions on these products. Performance Effective area mm Sonic conductance C [dm 3 /(s bar)] Recommended flow m 3 /min(nr) N0-M 0.4 or less N or less N or less N or less N or less N or less Note) Recommended flow rate is the flow at 7.psi (0. MPa) in the inlet pressure. Weight g Construction/Parts/imensions N0/0/ N/30/40 No hexagonal part in N0 and N0 Sound absorbing material (Resin sintered body) Body (Resin) Hexagonal flats imensions R, NPT N0-M M x 0.8 N0-0 /8 N-0 /4 N-0 /4 N /8 N40-04 / B (mm) 4 4 7

2 Silencer Compact Resin Type/One-touch Fitting Connection N0 to 30-C RoHS How to Order N C 0 C Specifications Body size 0 30 Connection type Connection type One-touch fitting connection pplicable one-touch fitting size pplicable model ø6 ø/4 ø8 ø0 ø3/8 ø N0 N0 N N N N30 Fluid Compressed air Max. operating pressure Note ) 4psi (.0 MPa) Noise reduction 30 db() Note ) mbient and fluid temperature 4 to 40 F ( to 60ºC) Note 3) Note ) It indicates the inlet pressure for solenoid valve. Note ) The value may vary, depending on the pneumatic circuit or pressure that is exhausted from the solenoid valve. Note 3) The product can be used in temperatures 4 to 40 F ( 0 to 60 C) if there is no risk of water droplets forming and freezing. Refer to page for Precautions on these products. Performance Effective area mm Sonic conductance C [dm 3 /(s bar)] Recommended flow m 3 /min(nr) N0-C06 N0-C or less N-C or less N-C or less N-C 3.0 or less N30-C or less Note) Recommended flow rate is the flow at 7.psi (0. MPa) in the inlet pressure. Construction/Parts/imensions Weight g N0-C to 30-C C ød Sound absorbing material (Resin sintered body) Body (Resin) imensions N0-C N0-C07 N-C08 4 N-C0 7. N-C N30-C 7. B 3 6. C (mm) ød ø6 ø/4 ø8 ø0 ø3/8 ø 3

3 Silencer Metal Body Type N 00 RoHS Noise reduction 30 db() Low back pressure Easy mounting N Body size How to Order Thread type Type Nil R N NPT pplicable model /4 /4 / N00 N600 N700 N800 N900 Specifications JIS Fluid Max. operating pressure Note ) Noise reduction mbient and fluid temperature Compressed air 4psi (.0 MPa) 30 db() Note ) 4 to 40 F ( to 60ºC) Note 3) Note ) It indicates the inlet pressure for solenoid valve. Note ) The value may vary, depending on the pneumatic circuit or pressure that is exhausted from the solenoid valve. Note 3) The product can be used in temperatures 4 to 40 F ( 0 to 60 C) if there is no risk of water droplets forming and freezing. Refer to page for Precautions on these products. Performance Effective area mm Sonic conductance C [dm 3 /(s bar)] N00-06 N600-0 N700- N800-4 N or less or less 30 or less 0 or less 80 or less Note) Recommended flow rate is the flow at 7.psi (0. MPa) in the inlet pressure. Construction/Parts/imensions Recommended flow m 3 /min(nr) Weight g N00 to 900 End plate (Carbon steel) Tension bolt (Carbon steel) Sound absorbing material (Resin sintered body) Cover (Carbon steel) Body (luminum alloy) Hexagonal flats imensions N00-06 N600-0 N700- N800-4 N900- R, NPT 3/4 /4 / B (mm)

4 N Specific Product Precautions Be sure to read before handling. Refer to back cover for Safety Instructions. Warning esign. The silencer clogging may result in a blocked exhaust port. Provide a safety design so as not to cause the whole system to malfunction.. The silencer is intended to reduce the noise of compressed air that is exhausted from the pneumatic equipment. Since noises generated by sources other than the exhaust, such as noise generated inside piping, equipment vibration and solenoid valve switching, cannot be reduced, locate the cause of these noises and take countermeasures. The product does not function as a filter. o not use the product as a filter regardless of negative and positive pressures.. If the compressed air supply is contaminated with fluids such as oil and oil mist, such fluids will be dispersed to the environment. In such a case, an exhaust cleaner is recommended to recover fluids and reduce noise. 3. The value of the noise reduction may vary, depending on the pneumatic circuit or pressure that is exhausted from the solenoid valve. Selection. When selecting the silencer, the sonic conductance (including combined sonic conductance) of the silencer should be larger than that of the solenoid valve. Sonic conductance C [dm 3 /(s bar)] = Effective area [mm ]. Use within the range of specifications. Operating Environment Warning. o not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. Refer to the construction drawings for silencer materials.. void exposure to direct sunlight. 3. o not operate in locations where vibration or impact occurs. 4. o not use the product in locations where it is near heat sources and exposed to radiation heat.. o not use in an environment where the product is exposed to cutting oil, lubricating oil, or coolant, etc. If it is used in an environment where there is possible contact with cutting oil, lubricating oil, or coolant, exercise preventive measures. 6. o not use in an environment where foreign matter may stick to the product or get mixed in the product s interior. It may result in clogging at an early stage, coming off or causing damage. Silencer Tightening Torque (Metal type) Connection thread R 3/4 R R /4 R / R Mounting. If the silencer body is made of resin and is tightened too much, the silencer may be damaged.. Tightening by using a pipe wrench or pliers may cause damage to the silencer. This method is not recommended. Please follow the procedures below for mounting. When the body is made of resin Hold the tip of the body (the side without thread) and screw it in. t the point where the thread begins to feel tight, use a wrench on the hexagonal flats to tighten an additional /4 turn. Tighten the N0-M by hand completely until the ends of the fitting come into contact with the mounting surface. Then apply additional tightening. Note that the additional tightening should be 30 or less. (Tighten it with 0. N m or less.) Silencer When the body is made of metal Within the recommended tightening torque shown in the table below, use a wrench on the hexagonal flats and tighten. pplicable tightening torque N m 8 to to to 4 48 to 0 48 to 0 3. Make sure not to apply a lateral load to the body during or after the installation. 4. When the silencer body is loosened by vibration, etc. of equipment on which a silencer is assembled, apply glue to threads to prevent loosening and reattach. Maintenance. The sound absorbing material is not replaceable. Since the sound absorbing material is not replaceable, never disassemble the product.. If the exhaust speed drops and the system performance decreases due to clogging, replace with a new silencer. Make sure to verify the operating conditions of the actuator at least once a day. 3. If operation continues when it is clogged, breakage can result.

5 Silencers/Exhaust Cleaner N / MC Noise reduction Nominal filtration rating (Reference values) Oil mist removal ratio Standard type Low back pressure Compact and easy mounting N db () 00 µm 0 µm -0- Compact type Space-saving compact type N 03 db () 00 µm -0-3 Silencers Metal case type Exhaust in only one direction. Prevents scattering of mist and noise. BC sintered body type Ideal for the exhaust of a compact valve or pilot air. One-touch fitting connection type Can connect with One-touch fitting directly. N0-0 N0-0 N-M N-M3 N -KM 9 db () 6 db () db () 8 db () 3 db () db () 30 db () It differs depending upon the model. 00 µm 70 µm 00 µm VEX N MC High noise reduction type Case adopts UL94-V0 grade flame resistant material. N 0 3 db () 0 µm -0-7 High noise reduction type high noise reduction type silencer keeps the noise level inside a plant below 8 db (). N 40 db () 30 µm -0-8 High noise reduction type NB has a larger effective area with the same port size as N. NB 38 db () 30 µm -0-9 Exhaust Cleaner Exhaust cleaner Ensures clean plant air, reduces noise pollution by over 3 db (), and removes over 99.9% of all oil mist. MC 3 db () 0.3 µm 99.9% -0- Precautions/Specific Product Precautions -0-3 Related Products Exhaust Cleaner for Vaccum ( MV) Exhaust Cleaner for Clean Room ( MP)

6 .34 IR P REPRTION: CCESSORIES S ILENCERS S ERIES (N)N S ERIES (N)N SILENCER M3, M, 8 S INTERE B RONZE Suitable for miniature valves and pilot air exhaust ports 3 - db noise reduction T ECHNICL SPECIFICTIONS NN0-0 NN0-0 NN-M3 NN-M Port Size 8 * 8 * M3 M Noise Reduction (db) Max Operating Pressure MPa / 4PSI mbient & Fluid Temperature ~0 C / 40~300ºF Effective Orifice mm (Cv) (.) 3 (.9) (0.0) (0.7) Weight (gf) H O W T O O R E R SERIES NN SILENCER NN-M3 (M3) NN-M (M) NN0-N0 ( 8 NPT) NN0-N0 ( 8 NPT) *Tapered thread ISO7/ S Y M B O L S IMENSIONS SERIES NN SILENCER ØB H O W T O O R E R SERIES N SILENCER N-M3 (M3) N-M (M) N0-0 ( 8 PT) N0-0 ( 8 PT) NN0-N0. NN0-N NN-M3 9 6 NN-M 7 8 S ERIES (N)N SILENCER 4~ Over 30 db noise reduction Low back pressure Compact and easy mounting T ECHNICL SPECIFICTIONS S Y M B O L S Max Operating Pressure MPa / 4PSI Noise Reduction 30dB or more H O W T O O R E R SERIES NN SILENCER mbient & Fluid Temperature ~60 C / 40~40ºF Port Size* NPT Effective Orifice mm (Cv) NN0-N0 4 3 (.9) NN300-N (3.3) NN400-N04 90 (.0) NN00-N (8.8 NN600-N0 70 () NN700-N (4) NN800-N4 90 (33) NN900-N 960 (3) Note: When ordering PT Ports, remove (N) from Number Eg: N0-0 IMENSIONS SERIES NN SILENCER imensions (mm) B NN0-N NN300-N03 84 NN400-N NN00-N NN600-N NN700-N 0 74 NN800-N NN900-N FOR FURTHER TECHNICL ETILS ON THIS PROUCT, REQUEST CTLOG REFERENCE N0