Series AN /Series AMC

Transcription

1 s/exhaust Cleaner / Noise reduction Nominal filtration rating (eference values) Oil mist removal ratio Standard type Low back pressure Compact and easy mounting db (A) 00 µm 50 µm Compact type Space-saving compact type db (A) 00 µm Silencers Metal case type Exhaust in only one direction. Prevents scattering of mist and noise. BC sintered body type Ideal for the exhaust of a compact valve or pilot air. One-touch fitting connection type Can connect with One-touch fitting directly M5 20-M3 -KM 9 db (A) 6 db (A) 2 db (A) 8 db (A) 3 db (A) 25 db (A) 30 db (A) It differs depending upon the model. 00 µm 70 µm 00 µm High noise reduction type adopts UL94-V0 grade flame resistant material db (A) 50 µm High noise reduction type A high noise reduction type silencer keeps the noise level inside a plant below 85 db (A). A 40 db (A) 30 µm High noise reduction type B has a larger effective area with the same port size as A. B 38 db (A) 30 µm Exhaust Cleaner Exhaust cleaner Ensures clean plant air, reduces noise pollution by over 35 db (A), and removes over 99.9% of all oil mist. 35 db (A) 0.3 µm 99.9% 5-0- Precautions/Specific Product Precautions elated Products Exhaust Cleaner for Vaccum ( AMV) Exhaust Cleaner for Clean oom ( AMP)

2 Standard Type 00 Over 30 db (A) noise reduction Low back pressure Compact and easy mounting How to Order Body size Thread type Nil N NPT /4 3/8 /2 3/4 /4 /2 2 Flow Characteristics (Initial conditions) 200 to 900 Inlet pressure (MPa) Noise Level (Initial conditions) 200 to 900 Condition: 0.5 MPa at inlet pressure of solenoid valve Measurement distance: 200 to 500 m, 600 to m, 800 to m Noise level (db) (A) Air flow (l/min ()) Without silencer With silencer Max. operating pressure () Noise reduction 200 to to MPa 30 db (A) 5 to 60 C (2) Note ) It indicates the inlet pressure for solenoid valve. Note 2) It can operate in temperature between 0 to 60 C if there is no risk of the moisture in the air freezing. efer to page for Precautions on these products. Effective area (mm 2 ) ecommended flow (m 3 /min ()) Weight (g) Dimensions (mm) A B D or less or less or less or less or less or less or less or less Tension bolt Cover Body Note ) About the display of product s material POM: Polyacetal PE: Polyethylene SPCC: Carbon steel S20C: Carbon steel ADC: Aluminum alloy Note 2) ecommended flow rate is the flow at 0.5 MPa in the inlet pressure.

3 Compact Type 03 Over 25 db (A) noise reduction Space-saving compact type Flow Characteristics (Initial conditions) 03 to 403 Inlet pressure (MPa) How to Order Body size Max. operating pressure () Noise reduction Thread type Nil N NPT efer to page for Precautions on these products. Effective ecommended flow Weight Dimensions (mm) area (mm 2 ) (m 3 /min ()) (g) A B D or less or less or less or less /8 /4 3/8 /2.0 MPa 25 db (A) 5 to 60 C (2) Note ) It indicates the inlet pressure for solenoid valve. Note 2) It can operate in temperature between 0 to 60 C if there is no risk of the moisture in the air freezing. Element (PP sintered body) Body Air flow (l/min ()) Noise Level (Initial conditions) 03 to 403 Condition: 0.5 MPa at inlet pressure of solenoid valve Measurement distance: m 303/403 Noise level (db (A)) Without silencer With silencer Note ) About the display of product s material PP: Polypropylene PE: Polyethylene POM: Polyacetal Note 2) ecommended flow rate is the flow at 0.5 MPa in the inlet pressure

4 BC Sintered Body Type Ideal for the exhaust of a compact valve or pilot air. Flow Characteristics (Initial conditions) / M3 20-M5 () 8 8 M3 M5 Noise reduction (db (A)) Max. operating pressure (2).0 MPa 5 to 50 C (3) Effective area (mm 2 ) Weight (g) Dimensions (mm) A B Note ) NPT thread for 0 and 0 is also available. no. of NPT thread is 0- N0 and 0-N0. Note 2) It indicates the inlet pressure for solenoid valve. Note 3) It can operate in temperatures between 0 to 50 C if there is no risk of the moisture in the air freezing. efer to page for Precautions on these products M3 20-M5 Inlet pressure (MPa) BC sintered body Phosphor bronze Air flow (l/min ()) Note) About the display of product s material BC: Copper alloy Phosphor bronze: Copper alloy 5-0-5

5 One-touch Fitting Connection Type -KM Can connect with One-touch fitting directly. Max. operating pressure Note) Note) It indicates the inlet pressure for solenoid valve..0 MPa 5 to 60 C efer to page for Precautions on these products. 03-KM6 03-X X KM8 200-KM8 200-KM0 300-KM0 300-KM2 Applicable One-touch fitting size ø6 ( KQ) ø6 ( KQ, KJ) ø/4" ( KQ, KJ) ø8 ( KQ) ø8 ( KQ) ø0 ( KQ) ø0 ( KQ) ø2 ( KQ) Noise reduction (db (A)) Effective area (mm 2 ) ecommended flow (m 3 /min ()) Dimensions (mm) A B C or less or less or less or less KM6 03-X X KM8 (PP sintered) Body (PP) 03-X235 only od (C3604) Body (PP) (PP sintered) od (C3604) 00-KM (PE) (PE) od (C3604) Note ) About the display of product s material PP: Polypropylene PE: Polyethylene C3604: Copper alloy Note 2) ecommended flow rate is the flow at 0.5 MPa in the inlet pressure

6 High Noise eduction Type 02 Over 35 db (A) noise reduction adopts UL94-V0 grade Flame resistant material How to Order Body size Thread type Nil N NPT /4 3/8 /2 Flow Characteristics (Initial conditions) 202 to 402 Inlet pressure (MPa) Air flow (l/min ()) Max. operating pressure () Noise reduction efer to page for Precautions on these products. 302/402.0 MPa 35 db (A) 5 to 60 C (2) Note ) It indicates the inlet pressure for solenoid valve. Note 2) It can operate in temperature between 0 to 60 C if there is no risk of the moisture in the air freezing. Effective ecommended flow Weight Dimensions (mm) area (mm 2 ) (m 3 /min ()) (g) A B D or less or less or less (PBT) (UL94-V0) (PVF) (PBT) (UL94-V0) (PVF) Noise Level (Initial conditions) 202 to 402 Condition: 0.5 MPa at inlet pressure of solenoid valve Measurement distance: m (PBT) (UL94-V0) D (PBT) (UL94-V0) D Noise level (db (A)) Without silencer With silencer Note ) About the display of product s material PBT : Polybutylene terephthalate PVF : Polyvinyl formal Note 2) ecommended flow rate is the flow at 0.5 MPa in the inlet pressure

7 s Precautions Be sure to read before handling. Warning Caution Caution on Design. The exhaust port could become blocked by the clogging of the exhaust cleaner. Therefore, make sure to provide a safe design so as not to cause the whole system to malfunction. 2. Silencer is intended to reduce the noise of exhaust air of the compressed air emitted from pneumatic equipment. Noises other than exhaust air (noise generated inside piping, noise generated by vibration of equipment, noise of switching valves, etc.) cannot be reduced. Take appropriate measures to find the cause of those noises other than those generated by exhaust air. 3. The inlet pressure obtained in the flow characteristic graph of silencer indicates the pressure (P) prior to silencer. (efer to the diagram below.) Solenoid P Inlet pressure for silencer Silencer 4. If the compressed air supply is contaminated with fluids such as oil and oil mist, such fluids will be dispersed to the environment. In such a case, an exhaust cleaner is recommended to recover fluids and reduce noise. 5. The silencing effect could vary depending on the pneumatic circuit or the pressure that is used. Selection Caution. Select a model which has a bigger effective area than that of the solenoid valve (including compound effective area). 2. Be certain to use at or below the level of recommended flow. Mounting Caution. If the silencer body (case) is made of plastic and is tightened too much, the silencer may be damaged. Please follow the procedures below for mounting. When the body (case) is made of resin Hold the tip of the main body (side without thread) and screw in. At the point where the thread begins to feel tight, use a wrench on the hexagonal flats to tighten an additional /4 turn. Tighten securely by hand for For BC element Hold the tip of the main body (side without thread) with fingers and screw in tightly. Do not hold the part of sintered metal with a wrench, etc. to tighten. When the main body is made of metal (Except BC element) [ 25] Within the recommended tightening torque shown in the chart below, use a wrench on the hexagonal flats and tighten. Tightening by using a pipe wrench or pliers may cause damage to the silencer. This method is not recommended. Tightening Torques for Silencers Connection thread 4 Applicable tightening torque (N. m) 2 to to to to to to to to Make sure not to apply a lateral load to the body during or after the installation. 3. When the main body of the silencer is loosened by vibration, etc. of equipment on which a silencer is assembled, apply glue to threads to prevent from loosing and reattach. Maintenance Caution. Never disassemble the silencer. The silencing material is not replaceable. 2. If the exhaust speed drops and the system performance decreases due to clogging, replace with a new silencer. Make sure to verify the operating conditions of the actuator at least once a day

8 5.34 A I P EPAATION: ACCESSOIES S ILENCES S EIES (N) S EIES (N) SILENCE M3, M5, 8 S INTEED B ONZE Suitable for miniature valves and pilot air exhaust ports 3-2 db noise reduction T ECHNICAL SPECIFICATIONS N0-0 N0-0 N20-M3 N20-M5 Port Size 8 * 8 * M3 M5 Noise eduction (db) Max Operating Pressure MPa / 45PSI Ambient & Temperature 5~50 C / 40~300ºF Effective Orifice mm 2 (Cv) 20 (.) 35 (.9) (0.05) 5 (0.27) Weight (gf) H O W T O O D E SEIES N SILENCE N20-M3 (M3) N20-M5 (M5) N0-N0 ( 8 NPT) N0-N0 ( 8 NPT) *Tapered thread ISO7/ S Y M B O L S D IMENSIONS SEIES N SILENCE A ØB H O W T O O D E SEIES SILENCE 20-M3 (M3) 20-M5 (M5) 0-0 ( 8 PT) 0-0 ( 8 PT) N0-N N0-N N20-M3 9 6 N20-M5 7 8 S EIES (N) SILENCE 4~2 Over 30 db noise reduction Low back pressure Compact and easy mounting T ECHNICAL SPECIFICATIONS S Y M B O L S Max Operating Pressure MPa / 45PSI Noise eduction 30dB or more H O W T O O D E SEIES N SILENCE Ambient & Temperature 5~60 C / 40~40ºF Port Size* NPT Effective Orifice mm 2 (Cv) N200-N (.9) N300-N (3.3) N400-N (5.0) N500-N (8.8 N600-N0 270 (5) N700-N (24) N800-N (33) N900-N (53) Note: When ordering PT Ports, remove (N) from Number Eg: D IMENSIONS SEIES N SILENCE Dimensions (mm) A B D N200-N N300-N N400-N N500-N N600-N N700-N N800-N N900-N FO FUTHE TECHNICAL DETAILS ON THIS PODUCT, EQUEST CATALOG EFEENCE N50