Air Filter Outdoor Series FW4000/FW8000-W Series Outdoor types now developed into a series. Port size: 1/4 to 1 JIS symbol Specifications Description

Transcription

1

2

3

4

5

6 ir Filter Outdoor Series FW4000/FW8000-W Series Outdoor types now developed into a series. : 1/4 to 1 JIS symbol Specifications FW4000-W FW8000-W Working fluid ompressed air Max. working pressure MPa 1.0 Note 1, 2 Proof pressure MPa 1.5 Fluid temperature 5 to 60 mbient -10 to 60 temperature (no freezing) Filtration rating μm 5 or 0.3 rain capacity cm (Note 3) Rc, NPT, G 1/4, 3/8, 1/2 3/4, 1 Weight kg Note 1: When "F" with auto-drain is selected, the min. operating pressure will be 0.1 MPa. ir is purged with initial drainage until pressure reaches 0.1 MPa. Note 2: When "F1" with an auto-drain is selected, min. dynamic pressure must be 0.15 MPa. Note 3: The max capacity of the manual pet cock type is 170 cm 3. Pressure drop (MPa) Pressure drop (MPa) Flow characteristics FW W FW W ir flow rate (m 3 /min(nr)) 0.1 MPa 0.5 MPa 0.7 MPa 0.3 MPa ir flow rate (m 3 /min (NR)) 0.1 MPa 0.3 MPa 0.5 MPa MPa ir flow rate (m 3 /min (NR)) Pressure drop (MPa) Pressure drop (MPa) MPa 0.5 MPa 0.1 MPa 0.7 MPa MPa (Max. flow rate) Value for the initial pressure drop of 0.01 MPa Primary pressure (MPa) ir flow rate (m 3 /min (NR)) FW W FW W 0.3 MPa 0.5 MPa 0.7 MPa ir flow rate (m 3 /min (NR)) FW4000/FW8000-*-W-Y (0.3 μm element) FW4000-*-W-Y Pressure drop (MPa) ontact K for large volume type FW8000-*-W-Y. FW W MPa 0.3 MPa 0.5 MPa 0.7 MPa ir flow rate (m 3 /min (NR)) 1 How to order FW W F Model No. Option Port thread type Note on model No. selection E ttachment (attached) Note 1: When G thread or NPT thread is selected, the,, and auto-drain ports come with the specified threads. Note 2: NPT thread and G thread are for export. Select Rc thread for use in Japan. (ue to the Japanese Measurement Law, the pressure must be in MPa and the temperature must be in degrees in Japan.) Note 3: Select options for drainage, element, warranty period, and flow direction. When selecting options for several items, list options in order from the top. Note 4: For the use conditions of auto-drain, refer to "Pneumatic, Vacuum, and uxiliary omponents" (atalog No. -024S). Note 5: For Option G, the warranty period is for three years after date of delivery or one year of use, whichever comes first. Note 6: For Option G, an agreement for the specification is required. 8 1/4 10 3/8 15 1/2 20 3/ Model No. Port thread type Note 1 Note 2 lank Rc thread (Pressure: MPa, Temperature: ) N NPT thread (Pressure: psi, Temperature: F) G G thread (Pressure: ar, Temperature: ) Option Note 3 lank With a manual pet cock rainage F utomatic drain manual override (NO type: Exhaust w/o pressurized) Note 4 F1 utomatic drain manual override (N type: No exhaust w/o pressurized) Element lank 5 μm Y 0.3 μm (submicron) lank One year after delivery Term of warranty Flow direction E G lank X1 Three years after delivery Note 5 Note 6 (Including inspection reports, inspection procedures, plans, specification sheet, and traceability system diagram) Standard flow (left right) Reverse flow (right left) ttachment (attached) lank Not attached W -type bracket FW4000 FW8000

7 Internal structure and parts list ir Filter Series Internal structure/dimensions FW4000-W FW8000-W No. Part name Material 1 ody luminum alloy die-casting 2 O ring Special nitrile rubber 3 Element Polypropylene 4 Metal bowl assembly 5 Plate cover luminum luminum alloy diecasting, brass, zinc alloy die-casting, nitrile rubber imensions FW4000-W (42.5) imension of Option With auto-drain (F, F1) Tube center dditional weight: 0.02 kg 2-Rc1/4 (8) Rc3/8 (10) Rc1/2 (15) ttachment (-type bracket) *1 187 Rc1/4 rain discharge port Width across flats 17 rain discharge port 60 Maintenance dimension ttachment -type bracket (-W) Part model No.: Weight: 0.21 kg 7 FW8000-W Tube center 45 imension of Option With auto-drain (F, F1) Tube center dditional weight: 0.02 kg 2-Rc3/4 (20) Rc1 (25) ttachment (-type bracket) * Rc1/4 rain discharge port Width across flats 17 rain discharge port ttachment type bracket (-W) Part model No.: Weight: 0.36 kg 60 Maintenance dimension *1: racket is an optional attachment. Tube center 2

8 Regulator Outdoor Series RW4000/RW8000-W Series Outdoor types now developed into a series. : 1/4 to 1 JIS symbol Specifications RW4000-W RW8000-W Working fluid ompressed air Max. working pressure MPa 1.0 Proof pressure MPa 1.5 Fluid temperature 5 to 60 mbient -10 to 60 temperature (no freezing) Set pressure MPa 0.05 to 0.85 Pressure relief Relief mechanism Rc, NPT, G 1/4, 3/8, 1/2 3/4, 1 Weight kg Secondary pressure (MPa) Secondary pressure (MPa) Flow characteristics RW W RW W Primary pressure 0.7 MPa ir flow rate (m 3 /min (NR)) ir flow rate (m 3 /min (NR)) Secondary pressure (MPa) Secondary pressure (MPa) Primary pressure 0.7 MPa Primary pressure 0.7 MPa ir flow rate (m 3 /min (NR)) RW W RW W Primary pressure 0.7 MPa ir flow rate (m 3 /min (NR)) Secondary pressure (MPa) RW W 0.6 Primary pressure 0.7 MPa ir flow rate (m 3 /min (NR)) Pressure characteristics RW4000-W RW8000-W How to order RW W K Secondary pressure (MPa) Set pressure Primary pressure (MPa) Secondary pressure (MPa) Set pressure Primary pressure (MPa) Model No. Model No. E ttachment (attached) 8 1/4 RW4000 RW8000 Option 10 3/8 15 1/2 20 3/ Port thread type Note on model No. selection Note 1: When G thread or NPT thread is selected, the,, and gauge ports come with the specified threads. Note 2: NPT thread and G thread are for export. Select Rc thread for use in Japan. (ue to the Japanese Measurement Law, the pressure must be in MPa and the temperature must be in degrees in Japan.) Note 3: Select options for knob, warranty period, and flow direction. When selecting options for several items, list options in order from the top. Note 4: For Option G, the warranty period is for three years after date of delivery or one year of use, whichever comes first. Note 5: For Option G, an agreement for the specification is required. Note 6: When NPT thread or G thread is selected, a pressure gauge cannot be included. (ontact K if you request a pressure gauge.) Knob Port thread type Note 1 Note 2 lank N G Term of warranty Flow direction E Rc thread (Pressure: MPa, Temperature: ) NPT thread (Pressure: psi, Temperature: F) G thread (Pressure: ar, Temperature: ) Option Note 3 Note 4 lank Without knob K lank With knob One year after delivery Three years after delivery Note 4 Note 5 G (Including inspection reports, inspection procedures, plans, specification sheet, and traceability system diagram) lank Standard flow (left right) X1 Reverse flow (right left) ttachment (attached) lank Not attached W -type bracket GW49P Pressure gauge (GW49-6-P10) Note 6

9 Internal structure and parts list Regulator Series Internal structure/dimensions RW4000-W RW8000-W No. Part name Material 1 ottom plug luminum alloy die-casting 2 Valve assembly rass, hydrogenated nitrile rubber (polyacetal resin: RW4000 only) 3 ody luminum alloy die-casting 4 Stainless steel, nitrile iaphragm assembly rubber, aluminum 5 over luminum alloy die-casting 6 djusting screw assembly Stainless steel (nitrile rubber, polyacetal resin: RW4000 only) 7 daptor Stainless steel 8 Gauge plug assembly luminum, nitrile rubber, stainless steel 9 Threads Stainless steel luminum, nitrile rubber, 10 Seal plug assembly stainless steel 11 Plate cover luminum imensions RW4000-W Pressure gauge port size Rc1/8 * (83) imension of Option With knob (K) Tube center φ dditional weight: 0.1 kg 2-Rc1/4 (8) Rc3/8 (10) Rc1/2 (15) Hexagon nut Width across flats Width across flats 6 φ 46.6 ttachment (pressure gauge) ttachment (-type bracket) *2 ttachment -type bracket (-W) Part model No.: Weight: 0.21 kg Tube center RW8000-W Pressure gauge port size Rc1/8 *1 2-Rc3/4 (20) Rc1 (25) Hexagon nut Width across flats *3 Width across flats 6 φ 46.6 ttachment (pressure gauge) (96) ttachment (-type bracket) *2 imension of Option With knob (K) Tube center φ *3 ttachment -type bracket (-W) Part model No.: dditional weight: 0.1 kg Weight: 0.36 kg *1: The pressure gauge port is not sealed when delivered. Use the pipe plug which comes with the product if you want to seal it. *2: racket is an optional attachment. *3: imension at setting pressure 0 MPa 9 Tube center

10 Lubricator Outdoor Series LW4000/LW8000-W Series Supplies fine oil mist. : 1/4 to 1 JIS symbol Specifications LW4000-W LW8000-W Working fluid ompressed air Max. working pressure MPa 1.0 Proof pressure MPa 1.5 Fluid temperature 5 to 60 mbient -10 to 60 temperature (no freezing) Min. drip flow Note 1 m 3 /min (NR) Oil capacity cm (MX360) Note 2 Recommended oil Turbine oil lass 1 ISO VG32 (spindle oil cannot be used) Rc, NPT, G 1/4, 3/8, 1/2 3/4, 1 (3/4 with adaptor) (1 1/4 with adaptor) Weight kg Note 1: The min. drip flow is the rate of five drops of turbine oil per minute at the primary pressure 0.5 MPa and inlet air temperature of 20. (This cannot be used for dry fog.) Note 2: When you refill oil from the fill plug, the amount should be 300 cm 3 or less above the bowl window. Pressure drop (MPa) Pressure drop (MPa) Flow characteristics LW W LW W 0.1 MPa 0.3 MPa ir flow rate (m 3 /min (NR)) LW W LW W 0.1 MPa Oil drip rate Oil drip rate (drops/minute) MPa 0.7 MPa 0.3 MPa 0.5 MPa 0.7 MPa MPa 0.3 MPa 0.5 MPa 0.7 MPa ir flow rate (m 3 /min (NR)) 0.1 MPa 0.3 MPa 0.5 MPa 0.7 MPa ir flow rate (m 3 /min (NR)) ir flow rate (m 3 /min (NR)) 10 Primary pressure 9 Max. drip rate 0.7 MPa 8 7 High lubrication Standard 6 lubrication Low lubrication ir flow rate (m 3 /min (NR)) Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) LW W MPa 0.3 MPa 0.5 MPa 0.7 MPa ir flow rate (m 3 /min (NR)) 5 How to order LW4000 Model No. 8 W Port thread type Option Note on model No. selection Note 1: When G threads or NPT threads are selected, the and are the targets. Note 2: When selecting options for several items, list options in order from the top. Note 3: NPT thread and G thread are for export. Select Rc thread for use in Japan. (ue to the Japanese Measurement Law, the pressure must be in MPa and the temperature must be in degrees in Japan.) Note 4: For Option G, the warranty period is for three years after date of delivery or one year of use, whichever comes first. Note 5: For Option G, an agreement for the specification is required. E racket (attached) * For the description of the options, refer to "Pneumatic, Vacuum and uxiliary omponents" (atalog No. -024S). 8 1/4 10 3/8 15 1/2 20 3/ Model No. Port thread type Note 1, Note 3 lank Rc thread N NPT thread G G thread Option Note 2 lank Without manual cock rainage With a manual pet cock lank One year after delivery Term of warranty Flow direction E Three years after delivery Note 4 Note 5 G (Including inspection reports, inspection procedures, plans, specification sheet, and traceability system diagram) lank Standard flow (left right) X1 Reverse flow (right left) racket (attached) lank Not attached W -type bracket LW4000 LW8000

11 Internal structure and parts list Lubricator Series Internal structure/dimensions LW4000-W LW8000-W No. Part name Material 1 ody luminum alloy die-casting 2 O ring Special nitrile rubber 3 Flow guide Nitrile rubber 4 5 Metal bowl assembly djusting doom assembly luminum alloy die-casting, zinc alloy die-casting, stainless stee Stainless steel, nitrile rubber, polycarbonate plastic 6 oom cover luminum 7 O ring Nitrile rubber 8 Filling plug Stainless steel 9 Plate cover luminum imensions LW4000-W 80 (42.5) imension of Option With a manual pet cock () Tube center Rc1/4 (8) Rc3/8 (10) Rc1/2 (15) 152 ttachment (-type bracket) *1 rain discharge port 115 Maintenance dimension ttachment -type bracket (-W) Part model No.: Weight: 0.21 kg LW8000-W Tube center imension of Option With a manual pet cock () Tube center Rc3/4 (20) Rc1 (25) ttachment (-type bracket) *1 rain discharge port ttachment -type bracket (-W) Part model No.: Weight: 0.36 kg rain discharge port 115 Maintenance dimension *1: racket is an optional attachment. 9 Tube center

12 Oil Mist Filter Outdoor Series MW4000/MW8000-W Series Outdoor types now developed into a series. : 1/4 to 1 JIS symbol Specifications MW4000-W MW8000-W Working fluid ompressed air Working pressure MPa 0.1 to 1.0 Note 2 Proof pressure MPa 1.5 rain capacity cm Rc, NPT, G 1/4, 3/8, 1/2 3/4, 1 Weight kg Flow rate l/min (NR) Flow characteristics (Max. flow rate) MW*000-W-M MW*000-W-S MW8000-M 1000 MW4000-M 100 Flow rate l/min (NR) MW8000-S MW4000-S Primary side pressure (MPa) Primary side pressure (MPa) Mantle option name lank (M-type) S (S-type) Max. flow rate Note 1 l/min (NR) MW4000-*-W Primary side pressure 0.7 MPa MW8000-*-W Fluid temperature 5 to 60 mbient temperature -10 to 60 (no freezing) Filtration rating μm 0.01 (nominal) 0.3 Secondary side oil mg/m 3 concentration Mantle (element) replacement 0.01 or less (0.1 or less after oil saturation) 0.5 or less Note 3 Note 3, Note 4 1 year (6000 hours) or pressure drop 0.1 Mpa Note 1: Use within the max. processing flow rate. If the max. processing flow is exceeded temporarily, or if the filter is installed at a place with high levels of pulsation, the mantle could be damaged or oil or drainage, etc., could splatter to the secondary side and result in faults at the terminal. Note 2: For "F1" with an auto-drain, the min. dynamic pressure is 0.15 MPa. Note 3: The secondary oil concentration is the value when the primary oil concentration is 30 mg/m 3 and inlet air temperature is 21. Note 4: Install an oil mist filter (S-type) as a pre-filter on the primary side to prevent early clogging. 7 How to order MW Model No. W Option Port thread type Note on model No. selection ttachment (attached) Note 1: When G thread or NPT thread is selected, the,, and auto-drain ports come with the specified threads. Note 2: NPT thread and G thread are for export. Select Rc thread for use in Japan. (ue to the Japanese Measurement Law, the pressure must be in MPa and the temperature must be in degrees in Japan.) Note 3: Select options for drainage, mantle, warranty period, and flow direction. When selecting options for several items, list options in order from the top. Note 4: NO auto-drain cannot be selected. Note 5: For the use conditions of auto-drain, refer to "Pneumatic, Vacuum, and uxiliary omponents" (atalog No. -024S). Note 6: For Option G, the warranty period is for three years after date of delivery or one year of use, whichever comes first. Note 7: For Option G, an agreement for the specification is required. S E 8 1/4 10 3/8 15 1/2 20 3/ Model No. Port thread type Note 1 Note 2 lank Rc thread (Pressure: MPa, Temperature: ) N NPT thread (Pressure: psi, Temperature: F) G G thread (Pressure: ar, Temperature: ) Option Note 3 rainage lank With a manual pet cock Note 4 Note 5 F1 utomatic drain manual override (N type: No exhaust w/o pressurized) Mantle (element) Term of warranty Flow direction E lank M-type (nominal 0.01 μm; remaining oil 0.01 mg/m 3 ) S S-type (nominal 0.3 μm; remaining oil 0.5 mg/m 3 ) lank One year after delivery Three years after delivery Note 6 Note 7 G (Including inspection reports, inspection procedures, plans, specification sheet, and traceability system diagram) lank Standard flow (left right) X1 Reverse flow (right left) ttachment (attached) lank Not attached W -type bracket M W M W

13 Internal structure and parts list Oil Mist Filter Series Internal structure/dimensions MW4000-W MW8000-W No. Part name Material 1 ody luminum alloy die-casting 2 O ring Special nitrile rubber 3 Mantle assembly - 4 Metal bowl assembly 5 Plate cover luminum luminum alloy die-casting, brass, zinc alloy die-casting, nitrile rubber imensions MW4000-W (42.5) imension of Option With auto-drain (F1) Tube center 187 dditional weight: 0.02 kg 2-Rc1/4 (8) Rc3/8 (10) Rc1/2 (15) ttachment (-type bracket) *1 rain discharge port 60 Maintenance dimension Rc1/4 rain discharge port ttachment -type bracket (-W) Part model No.: Width across flats 17 Weight: 0.21 kg 7 MW8000-W Tube center 45 imension of Option With auto-drain (F1) Tube center dditional weight: 0.02 kg 2-Rc3/4 (20) Rc1 (25) ttachment (-type bracket) *1 298 Rc1/4 rain discharge port Width across flats 17 ttachment -type bracket (-W) Part model No.: Weight: 0.36 kg rain discharge port 200 Maintenance dimension *1: racket is an optional attachment. Tube center 8

14 Filter and Regulator Outdoor Series WW4000/WW8000-W Series Outdoor types now developed into a series. : 1/4 to 1 JIS symbol 9 Specifications WW4000-W WW8000-W Working fluid ompressed air Max. working pressure MPa 1.0 Note 1, 2 Proof pressure MPa 1.5 Fluid temperature 5 to 60 mbient -10 to 60 temperature (no freezing) Filtration rating μm 5 or 0.3 Set pressure MPa 0.05 to 0.85 Pressure relief Relief mechanism rain capacity cm (Note 3) Rc, NPT, G 1/4, 3/8, 1/2 3/4, 1 Weight kg Note 1: When "F" with auto-drain is selected, the min. operating pressure will be 0.1 MPa. ir is purged with initial drainage until pressure reaches 0.1 MPa. Note 2: When "F1" with an auto-drain is selected, min. dynamic pressure must be 0.15 MPa. Note 3: The max capacity of the manual pet cock type is 170 cm 3. How to order WW4000 Model No. 68 W F Note on model No. selection ttachment (attached) Note 1: When G thread or NPT thread is selected, the,, gauge, and auto-drain ports come with the specified threads. Note 2: NPT thread and G thread are for export. Select Rc thread for use in Japan. (ue to the Japanese Measurement Law, the pressure must be in MPa and the temperature must be in degrees in Japan.) Note 3: Select options for drainage, element, knob, warranty period, and flow direction. When selecting options for several items, list options in order from the top. Note 4: For the use conditions of auto-drain, refer to "Pneumatic, Vacuum, and uxiliary omponents" (atalog No. -024S). Note 5: Refer to page 7 for max. flow when option "Y" is selected. Note 6: For Option G, the warranty period is for three years after date of delivery or one year of use, whichever comes first. Note 7: For Option G, an agreement for the specification is required. Note 8: When NPT thread or G thread is selected, a pressure gauge cannot be included. (ontact K if you request a pressure gauge.) E Option Port thread type Secondary pressure (MPa) Secondary pressure (MPa) Secondary pressure (MPa) Flow characteristics WW W WW W Primary pressure 0.7 MPa Primary pressure 0.7 MPa ir flow rate (m 3 /min (NR)) ir flow rate (m 3 /min (NR)) WW W WW W 0.6 Primary pressure 0.7 MPa ir flow rate (m 3 /min (NR)) Set pressure Primary pressure (MPa) Secondary pressure (MPa) Secondary pressure (MPa) Primary pressure 0.7 MPa ir flow rate (m 3 /min (NR)) Pressure characteristics WW4000-W Secondary pressure (MPa) 8 1/4 10 3/8 15 1/2 20 3/ WW8000-W Set pressure Primary pressure (MPa) Secondary pressure (MPa) WW W Primary pressure 0.7 MPa ir flow rate (m 3 /min (NR)) Model No. Port thread type Note 1 Note 2 lank Rc thread (Pressure: MPa, Temperature: ) N NPT thread (Pressure: psi, Temperature: F) G G thread (Pressure: ar, Temperature: ) Option Note 3 Note 4 lank With a manual pet cock rainage F utomatic drain manual override (NO type: Exhaust w/o pressurized) Note 4 F1 utomatic drain manual override (N type: No exhaust w/o pressurized) Element lank 5 μm Y 0.3 μm (submicron) Note 5 lank Without knob Knob K With knob lank One year after delivery Term of Three years after delivery Note 6 Note 7 warranty G (Including inspection reports, inspection procedures, plans, specification sheet, and traceability system diagram) Flow lank Standard flow (left right) direction X1 Reverse flow (right left) E ttachment (attached) lank Not attached W -type bracket GW49P Pressure gauge (GW49-6-P10) Note 8 WW4000 WW8000

15 Internal structure and parts list Filter/Regulator Series Internal structure/dimensions WW4000-W WW8000-W No. Part name Material 1 djusting screw assembly Stainless steel (nitrile rubber, polyacetal resin: WW4000 only) 2 over luminum alloy die-casting 3 iaphragm assembly Stainless steel, nitrile rubber, aluminum 4 ody luminum alloy die-casting 5 Valve assembly rass, hydrogenated nitrile rubber (polyacetal resin: WW4000 only) 6 Element Polypropylene 7 Metal bowl assembly luminum alloy die-casting, brass, zinc alloy die-casting, nitrile rubber 8 daptor Stainless steel 9 Threads Stainless steel 10 Gauge plug assembly luminum, nitrile rubber, stainless steel 11 Seal plug assembly luminum, nitrile rubber, stainless steel 12 O ring Special nitrile rubber imensions WW4000-W Width across flats 6 Hexagon nut Width across flats 17 Pressure gauge port size Rc1/8 *1 2-Rc1/4 (8) Rc3/8 (10) Rc1/2 (15) rain discharge port φ 46.6 Maintenance dimension (83) (42.5) ttachment (-type bracket) *2 imension of Option With knob (K) dditional weight: kg φ 15.5 Tube center 128 ttachment -type bracket (-W) Part model No.: Weight: kg 14 7 Tube center With auto-drain (F, F1) Tube center 187 dditional weight: 0.02 kg Width across flats 17 Rc1/4 rain discharge port WW8000-W Width across flats 6 Hexagon nut Width across flats 17 Pressure gauge port size Rc1/8 *1 2-Rc3/4 (20) Rc1 (25) *3 250 φ 46.6 (96) ttachment (-type bracket) *2 imension of Option With knob (K) dditional weight: kg φ 15.5 Tube center 178 *3 ttachment -type bracket (-W) Part model No.: Weight: 0.36 kg With auto-drain (F, F1) Tube center 266 dditional weight: 0.02 kg Width across flats 17 Rc1/4 rain discharge port rain discharge port 60 Maintenance dimension 50 9 Tube center *1: The pressure gauge port is not sealed when delivered. Use the pipe plug which comes with the product if you want to seal it. *2: racket is an optional attachment. *3: imension at setting pressure 0 MPa 10

16 Filter and Regulator Outdoor Series W7019 Series ir filter/regulator integrated. : Rc1/4 JIS symbol Specifications W7019 Max. working pressure MPa 1.0 Proof pressure MPa 1.5 Fluid temperature 5 to 60 mbient temperature -10 to 60 (no freezing) Filtration rating μm 5 Set pressure MPa 0.04 to 0.83 Pressure relief Relief mechanism Rc 1/4 Weight kg 0.45 Note 1: When a piston drain () is used, min. operating pressure is 0.1 MPa. o not use this type for devices to which impact is applied. How to order W Option Note on model No. selection Note 1: For Option G, the warranty period is for three years after date of delivery or one year of use, whichever comes first. Note 2: For Option G, an agreement for the specification is required. ttachment (attached) Flow characteristics Secondary pressure (MPa) W7019 Pressure characteristics Secondary pressure (MPa) W Rc1/4 Rc1/4 Option rainage lank Tire valve Piston drain Element lank 5 μm lank One year after delivery Term of Three years after delivery Note 1 Note 2 warranty G (Including inspection reports, inspection procedures, plans, specification sheet, and traceability system diagram) Flow direction ir flow rate (m 3 /min (NR)) lank X1 Set point Primary pressure (MPa) Standard flow (left right) Reverse flow (right left) ttachment (attached) lank Not attached GW49P Pressure gauge (GW49-6-P10) W racket (6506-W) 1.0 Optional weight * dd to the weight of the standard accessories. Unit: kg rainage owl material Pressure gauge racket Symbol Z M Q G W

17 Internal structure and parts list W7019 Series Internal structure and parts list/dimensions W No. Part name Material 1 djusting screw Stainless steel 2 over Zinc alloy die-casting, aluminum 3 iaphragm assembly Nitrile rubber, copper, zinc alloy die-casting 4 ody luminum alloy die-casting 5 Valve assembly rass/hydrogenated nitrile rubber 6 O ring Special nitrile rubber 7 Element Polypropylene 8 Metal bowl assembly Zinc alloy die-casting imensions W7019 Width across flats 5 Hexagon nut Width across flats ttachment racket (-W) Part model No.: 6506-W Pressure gauge port size 2-Rc1/ Weight: 0.03 kg 6 2-Rc1/ Tube center Maintenance dimension 12

18 uxiliary components racket W Series Joiner JW Series imensions T-type bracket set enter of port size H K Joiner set I E E F G J Model No. pplicable model E F G H I J K Weight (kg) W410-W 4000 Series JIS2401-P W810-W 8000 Series S Model No. pplicable model E Weight (kg) Series M5 JIS JW400-W 2401-P JW800-W 8000 Series M6 S uxiliary components Piping adaptor W400/W800 Series : Rc1/4 to Rc11/4 13 imensions Piping adaptor set Piping adaptor set F E F E Model No. pplicable model E (O ring) F (gasket) Others W400-8-W Rc 1 / 4 The figure in W W Rc 3 / JIS2401 ( ) indicates 4000 W W Rc 1 / (25) (11) P21 1 pc. Rc Series 3 2 / 4 W W Rc 3 / 4 {34} {20} 1 pc. The figure in W W Rc1 { } is for Rc1 W W Rc 3 / W W Rc1 Series W W Rc1 1 / 4 35 (38) 15 (18) S pc. 1 pc. The figure in ( ) indicates Rc1 1 / 4 Model No. pplicable model E (O ring) F (gasket) Others W400-8-W-41W Rc 1 / 4 The figure in W W-41W Rc 3 / JIS2401 ( ) indicates 4000 W W-41W Rc 1 / (25) (11) P21 1 pc. Rc Series 3 2 / 4 W W-41W Rc 3 / 4 {34} {20} 1 pc. The figure in W W-41W Rc1 { } is for Rc1 W W-81W Rc 3 / W W-81W Rc1 Series W W-81W Rc1 1 / 4 35 (38) 15 (18) S pc. 1 pc. The figure in ( ) indicates Rc1 1 / 4

19 Pressure Gauge Outdoor Series GW49 Series : R1/8, R1/4 JIS symbol Specifications imensions GW49 (51) Working fluid ompressed air Fluid temperature 5 to 60 mbient temperature -10 to 60 (no freezing) ccuracy Note 1 Full scale ±3% (for 5 to 35 ) Shape -type (rear side screw and hexagonal stock section) isplay system φ 46.6 (6.3) (28) 23 9 ourdon tube rass Material Stock Housing rass (nickel plating) Stainless steel φ 46.6 Lens Tempered glass Pressure range MPa 0 to 1.0 R 1/8, 1/4 weight g 100 R1/8 (6) R1/4 (8) HEX.14 Note 1: The guaranteed indicator accuracy temperature is 20 ±15. How to order GW49 6 P10 Model No. Model No. GW49 6 R 1 / 8 8 R 1 / 4 Pressure display Pressure display (MPa) Note 1 P10 0 to 1.0 MPa Note 1: ontact K when you want "psi" or "bar" indication. 14

20 Silencer Metal ody Type Outdoor Series SL-W Series : R1/4 to R1/2 JIS symbol Specifications SL-8-W SL-10-W SL-15-W Working fluid ompressed air Max. working pressure MPa 0.9 Min. working pressure MPa 0 Proof pressure MPa 1.35 Fluid temperature 5 to 60 mbient temperature -10 to 60 (no freezing) R 1/4 3/8 1/2 Weight g pplicable cylinder tube size φ 50 to φ 100 φ 63 to φ 140 φ 75 to φ 180 Noise reduction effect d [] 20 and over Flow rate Note 1 m 3 /min (NR) Effective cross-sectional area mm How to order SL 8 W Replacement element SL 8 EL 8 R1/4 10 R3/8 15 R1/2 Note 1: Flow rate is the atmospheric pressure conversion value when the pressure is at 0.5 MPa. imensions/internal structure and main parts list SL-8 to 15-W Model No. φ SL-8-W R1/ SL-10-W R3/ SL-15-W R1/ φ No. Parts name Material 1 -type snap ring Stainless steel 2 Punching metal Stainless steel 3 Wire net Stainless steel 4 Element Vinylidene chloride 5 ody luminum Safety precautions Use proper torque to tighten the pipes when connecting them. Noise reduction effect values are based on JIS Standards. Noise reduction effect may vary with the type of circuit and pressure. (Recommended tightening torque) Port thread Tightening torque N m R1/4 6 to 8 R3/8 13 to 15 R1/2 16 to 18 15

21 Speed ontroller Medium ore Type Outdoor Series S1-W Series : Rc1/4 to Rc1/2 JIS symbol Specification S1-8-W S1-10-W S1-15-W Working fluid Note 1: Flow rate is the atmospheric pressure conversion value when the pressure is at 0.5 MPa. ompressed air Max. working pressure MPa 1.0 Min. working pressure MPa 0.05 Proof pressure MPa 1.5 Fluid temperature 5 to 60 mbient temperature -10 to 60 (no freezing) Rc 1/4 3/8 1/2 Weight g pplicable cylinder bore size mm φ 32 to φ 75 φ 50 to φ 140 φ 80 to φ 160 Number of needle rotations Flow rate l/min (NR) Free flow Effective cross-sectional area mm ontrolled Flow rate l/min (NR) flow Effective cross-sectional area mm How to order S1 8 W Flow characteristics 8 Rc1/4 10 Rc3/8 15 Rc1/2 Flow rate l/min (NR) (Pressure at 0.5 MPa) S1-15-W S1-10-W S1-8-W Number of dial rotations Effective crosssectional area (mm 2 ) 16

22 I S1-W Series Internal structure and parts list No. Parts name Material 1 Needle Stainless steel 2 E-type snap ring Stainless steel 3 Knob luminum 4 Needle guide luminum alloy die-casting 5 Lock nut Stainless steel 6 O ring Fluoro rubber 7 Gasket Fluoro rubber 8 ody luminum alloy die-casting 9 Spring Stainless steel 10 Valve seat rass/fluoro rubber imensions S1-W φ K Mounting hole 2-*4.5 (penetrating) F E max G 8 : Rc1/4 10 : Rc3/8 15 : Rc1/2 4 H J Set screw 2-M4 (depth 6) S1-8-W Set screw 2-M5 (depth 6) S1-10/15-W Model No. E F G H I J K S1-8-W S1-10/15-W Safety precautions 17 Vibration noise may occur when using in low pressure range (0.05 MPa or less), when the piping diameter around the unit is very small, when the cylinder speed is fast, or when the differential pressure is small. When tightening, do not tighten needle or lock nut section excessively. (Tightening torque approx. 3 N m)

23 iscrete valve/body piping 5-port pilot operated valve pneumatic valve 4F2/3 Series Outdoor Type Options pplicable cylinder bore size: φ 40 to φ 100 JIS symbol 5-port valve 2-position single (1) (2) R1 P R2 (E1) (S) (E2) 2-position double X (1) (2) R1 P R2 (E1) (S) (E2) 3-position all ports closed X (1) (2) Y Y Y ommon specifications Valve type and operation Pilot operated type soft spool valve Working fluid ompressed air Max. working pressure MPa 1.0 Min. working pressure 2-position 0.1 MPa 3-position 0.15 Proof pressure 1.5 mbient temperature -10 to 60 Note 1 Fluid temperature 5 to 60 Lubrication Not required Note 2 egree of protection IP65 Vibration resistance m/s 2 50 or less Shock resistance m/s or less tmosphere ontaining corrosive gas is not permissible Note 1: The ambient temperature indicates the temperature for storage and installation. This differs from the fluid temperature during operation. Note 2: Use the turbine oil lass 1 ISO VG32 for lubrication. Electrical specifications Rated voltage 100, 200 (50/60 Hz) V Voltage fluctuation range ±10% 100 V 0.170/0.140 Starting 200 V 0.090/0.070 current 12 V V V 0.100/0.080 Holding 200 V 0.050/0.040 current 12 V V V 5.0/4.0 Power 200 V 5.0/4.0 consumption 12 V 6.0 W 24 V 6.0 Thermal class (molded coil) R1 P R2 (E1) (S) (E2) 3-position //R connection X (1) (2) R1 P R2 (E1) (S) (E2) 3-position P// connection Y Individual specifications 4F2 4F3 Weight kg Single position ouble position X (1) (2) R1 P R2 (E1) (S) (E2) Y Flow characteristics Sonic conductance Model No. Solenoid position [dm 3 /(s bar)] Single 2-position ouble 4F2 Rp1/4 ll ports closed 3-position //R connection Single 2-position ouble ll ports closed Rp1/ position //R connection P// connection F3 Single 2-position ouble ll ports closed Rp3/ position ritical pressure ratio b //R connection P// connection Note 4: Effective cross-sectional area S and sonic conductance are converted as S

24 4F2/4F3 Series (Outdoor type) How to order 4F M2 W 100V Model No. Model no. 4F2 4F2 Series 4F3 4F3 Series 4F2 4F3 Solenoid position Solenoid position 1 2-position single 2 2-position double 3 3-position all ports closed 4 3-position R connection 5 3-position P// connection Note 1 08 Rp1/4 10 Rp3/8 Manual operating device Manual operating device Note 2 lank Locking type (plastic) M2 Non-locking type (metal) M3 Locking type with manual override lever (plastic) R Position change of manual operating device E Electrical connections E Electrical connections 1 Round terminal box (G3/4) Round terminal box (G1/2) L Round terminal box (G1/2) with light Note 3 Round terminal box (G1/2) G With gland (-15a) Round terminal box (G1/2) with light Note 3 GL With gland (-15a) Note on model No. selection Note 1: We offer either Rc thread or NPT thread for piping ports. ontact K for details. Note 2: When you use the unit in a complete outdoor exposure environment, select the non-locking manual override M2 (metal). The metal locking manual override is available as a custom order product. ontact K for details. Note 3: 12 V models are not available for L with light and GL. Note 4: Support with a manifold is not available. Note 5: 4F4 to 7 outdoor types are available as custom order products. ontact K for details. <Example of model No.> 4F M2W-100V E F G Model Solenoid position Manual operating device Electrical connections Other options Voltage : 4F2 : 2-position single : Rp1/4 : Non-locking : Round terminal box (G1/2) : No option : 100 V F Other options G Voltage F Other options lank No option S With surge suppressor (varistor) H With check valve (only applicable to 3-position all ports closed) N With plug (for 3-port valve) N 3-port valve specifications plug assembly (1 (), E1 (R1) assembly) NO 3-port valve specifications plug assembly (2 (), E2 (R2) assembly) G Voltage 100V 100 V 50/60 Hz 200V 200 V 50/60 Hz 110V 110 V 50/60 Hz 220V 220 V 50/60 Hz 12V 12 V Note 3 24V 24 V * Other custom order products 48 V 100 V 110 V 19

25 0 1 1 imensions 4F2/4F3 Series (Outdoor type) iscrete valve/body piping 4F210/4F310 2-position single: round terminal box without indicator light E1 E2 X Y S 4F2:30 4F3:33 4F2:196 4F3: G1/2 or G3/4 Y 4F2:113 4F3:118 4F2:138 4F3:143 4F220/4F320 2-position double solenoid: round terminal box without indicator light X E1 S E2 Y 0 1 4F2:296 4F3: G1/2 or G3/4 X Y 4F2:113 4F3:118 4F2:138 4F3:143 4F2 3 40/4F position: round terminal box without indicator light E1 E2 X Y S 4F2:331 4F3: G1/2 or G3/4 X Y 4F2:113 4F3:118 4F2:138 4F3:143 20

26 F2/4F3 Series (Outdoor type) imensions 4F210/4F310 2-position single: round terminal box with indicator light E1 E2 X Y S 4F2:30 4F3:33 4F2:196 4F3: G1/2 Y 4F2:113 4F3:118 4F2:142 4F3:147 4F220/4F320 2-position double solenoid: round terminal box with indicator light X E1 S E2 Y 0 1 4F2:296 4F3: G1/2 X Y 4F2:113 4F3:118 4F2:142 4F3:147 4F2 3 40/4F position: round terminal box with indicator light E1 E2 X Y S 4F2:331 4F3: G1/2 X Y 4F2:113 4F3:118 4F2:142 4F3:147 21

27 Pilot kick type 2-port solenoid valve (general purpose valve) K11-W Series N (normally closed) type : Rc1/2 to Rc1 iaphragm structure JIS symbol K11: N (normally closed) type Mounting orientation ommon specifications Standard specifications Working fluid ir/low vacuum ( Pa (abs))/water/kerosene/oil (50 mm 2 /s or less) Operating pressure differential MPa 0 to 1.0 (Refer to max. operating pressure differential in individual specifications.) Max. working pressure MPa 2 Proof pressure (water pressure) MPa 4 Fluid temperature 5 to 60 mbient temperature -10 to 60 Thermal class lass 130 () Working environment Indoors/outdoors tmosphere Free of corrosive gases, liquids, chemicals, and explosive gases Valve structure Pilot kick type poppet, diaphragm structure Valve seat leakage (Note 1) cm 3 /min (NR) 1 or less (air) Mounting orientation Only vertical direction with the coil on the top ody and seal materials Stainless steel/fluoro rubber egree of protection IP65 Note 1: Value at pneumatic pressure of 0.02 to 1.0 MPa. When used at a pressure less than 0.02 MPa, the sealing may become unstable. ontact K in this case. Individual specifications Min. Max. operating pressure Orifice Port operating differential (MPa) pparent power (V) Power consumption (W) Weight size pressure Rated voltage size ir Water/ Oil (mm) differential kerosene (50 mm 2 /s) Holding Starting (kg) Model No. (MPa) 50/60 Hz 50 Hz 60 Hz 50 Hz 60 Hz N (normally closed) type K11-15 Rc1/ V 50/60 Hz K11-20 Rc3/ / V 50/60 Hz K11-25 Rc *1: The model Nos. above are for the basic port size (Rc). Refer to How to order for other combinations. *2: The voltage fluctuation range must be within ±10% of the rated voltage. Flow characteristics Model No. Orifice size Flow characteristics (mm) [dm 3 / (s bar)] b v S (mm 2 ) N (normally closed) type K11-15 Rc1/ K11-20 Rc3/ K11-25 Rc *1: Effective cross-sectional area S and sonic conductance are converted as S

28 K11-W Series How to order K11 25 E 3E Model No. Thread type oil housing ody/sealant combination S W E Mounting plate F Other options G Surge suppressor 15 1/2 20 3/ Thread type Rc ody/sealant combination ody Sealant Remarks E Stainless steel Fluoro rubber ir/low vacuum/kerosene/oil to H 100V H Rated voltage For details on the coil housing, other options and voltage, refer to the following table. <Example 1 of model No.> K11-15-E3EW-100V E H : 1/2 Thread type : Rc ody/sealant combination : ody - stainless steel, seal - fluoro rubber oil housing : Open frame type with round terminal box to G : None Rated voltage : 100 V 50/60 Hz, 110 V 60 Hz For to H, the combinations indicated with symbols can be manufactured. Note that if options E to G are not required, no symbol is indicated. oil housing E F Other options G H Rated voltage able gland (Marine cable gland) -15a -15b -15c 3E 3L Open frame type Round terminal box (G1/2) With round terminal box (G1/2) Mounting plate E F S 100 V, 200 V Surge suppressor Refer to the following cautions for E to H. Note on model No. selection Notes for E to G *1: For F, select an option from, E, and F. *2: The surge suppressor is mounted in the terminal box for the coil with terminal box. Notes for H *3: 100 V coil is compatible with 100 V 50/60 Hz and 110 V 60 Hz, and 200 V coil is compatible with 200 V 50/60 Hz and 220 V 60 Hz. 23

29 imensions: K11-W Series K11-W Series imensions Open frame type with round terminal box K11-15/20/25-E 3E 3L G1/2 49 E G F Model No. E F G K11-15-E3E/3L Rc1/2 K11-20-E3E/3L Rc3/4 K11-25-E3E/3L Rc1 24

30 K11-W Series imensions: K11-W Series Mounting plate K11-15/20/25-E* 2-Q 3.2 P M N Model No. M N P Q K11-15-E3E/3L φ 9 K11-20-E3E/3L φ 9 K11-25-E3E/3L φ 11 Open frame type with round terminal box and cable gland K11-15/20/25-E 3E 3L E F (39) 49 φ 9 (-15a) φ 10 (-15b) φ 11 (-15c) 28 25

31 ir operated type 2-port ball valve (compact rotary valve) H-W/H-WR* Series : Rc3/8 to Rc2 JIS symbol H-W (double acting) H-WR1 (single acting-n) H-WR2 (single acting-no) ommon specifications H-W H-WR* ctuation ir operated type: double acting ir operated type: single acting Working fluid Water/air/oil (500 mm 2 /s or less) Working pressure MPa 0 to 1.0 Proof pressure (water pressure) MPa 2.0 Fluid temperature 0 to 80 (no freezing) mbient temperature -10 to 60 (no freezing) Working environment Indoors/outdoors Valve seat leakage cm 3 /min 0 (initial value at water pressure 1 MPa) Mounting orientation Free Frequency times/min 1 or less Pilot fluid ompressed air Lubrication Not required (use turbine oil class 1 ISO VG32 if necessary) Proof pressure (water pressure) MPa 1.5 Working pressure MPa 0.35 to to 0.7 Fluid temperature 5 to 60 Rotary actuator Rc1/8 Rc1/8 Individual specifications Orifice size Weight (kg) v Model No. (mm) ouble acting Single acting H-W(R*)-10 Rc3/ H-W(R*)-15 Rc1/ H-W(R*)-20 Rc3/ H-W(R*)-25 Rc H-W(R*)-32 Rc1 1 / H-W(R*)-40 Rc1 1 / H-W(R*)-50 Rc Standard bore Note 1: H-W(R*)-10 is full bore type. 26

32 H-W/H-WR* Series How to order H WR1 15 E Model No. ctuator ody material W WR1 WR2 ctuator ouble acting type Single acting N (normally closed) type Single acting NO (normally open) type 10 Rc3/8 15 Rc1/2 20 Rc3/4 25 Rc1 32 Rc1 1 /4 40 Rc1 1 /2 50 Rc2 E ody material Stainless steel Model No. H (standard bore) <Example of model No.> H-WR1-15-E Model No.: H (standard bore) ctuator : Single acting N (normally closed) type : Rc1/2 ody material : Stainless steel 27

33 imensions: H-W Series H-W-10/15/20/25 H-W Series imensions Rc1/ E Model No. E H-W Rc3/8 H-W Rc1/2 H-W Rc3/4 H-W Rc1 H-W-32/40/ Rc1/ E Model No. E H-W Rc1 1 /4 H-W Rc1 1 /2 H-W Rc2 28

34 EXH H-WR* Series imensions: H-WR* Series H-WR*-10/15/ Rc1/8 34 EXH E Model No. E H-WR* Rc3/8 H-WR* Rc1/2 H-WR* Rc3/4 H-WR*-25/32/40/50 HG-WR*-40/50 ctuator Rc1/8 Rc1/8 39 EXH F G H E Model No. E F G H H-WR* Rc H-WR* Rc1 1 / H-WR* Rc1 1 / H-WR* Rc

35 ir operated type 3-port ball valve (compact rotary valve) HG-W/HG-WR* Series : Rc1/2 to Rc2 JIS symbol HG-W (double acting) HG-WR1 (Single acting, normally - path) HG-WR2 (Single acting, normally - path) ommon specifications HG-W HG-WR* ctuation ir operated type: double acting ir operated type: single acting Working fluid Water/air/oil (500 mm 2 /s or less) Working pressure MPa 0 to 1.0 Proof pressure (water pressure) MPa 2.0 Fluid temperature 0 to 80 (no freezing) mbient temperature -10 to 60 (no freezing) Working environment Indoors/outdoors Valve seat leakage cm 3 /min 0 (initial value at water pressure 1 MPa) Mounting orientation Free Frequency times/min 1 or less Pressurization direction Port pressurization only Flow path shape Multi-fluid type (90 rotation switching) Pilot fluid ompressed air Lubrication Not required (use turbine oil class 1 ISO VG32 if necessary) Proof pressure (water pressure) MPa 1.5 Working pressure MPa 0.35 to to 0.7 Fluid temperature 5 to 60 Rotary actuator Rc1/8 Rc1/8 Individual specifications Orifice size Weight (kg) v Model No. (mm) ouble acting Single acting HG-W(R*)-15 Rc1/ HG-W(R*)-20 Rc3/ HG-W(R*)-25 Rc HG-W(R*)-32 Rc1 1 / HG-W(R*)-40 Rc1 1 / HG-W(R*)-50 Rc

36 HG-W/HG-WR* Series How to order HG WR1 20 E Model No. ctuator ody material ctuator W ouble acting type WR1 Single acting type, normally - path WR2 Single acting type, normally - path 15 Rc1/2 20 Rc3/4 25 Rc1 32 Rc1 1 /4 40 Rc1 1 /2 50 Rc2 ody material E Stainless steel <Example of model No.> HG-WR1-20-E Model: HG ctuator : Single acting type, normally - path : Rc3/4 ody material : Stainless steel 31

37 imensions: HG-W Series HG-W-15/20/25 HG-W Series imensions Rc1/ E Model No. E HG-W Rc1/2 HG-W Rc3/4 HG-W Rc1 HG-W-32/40/ Rc1/ E Model No. E HG-W Rc1 1 /4 HG-W Rc1 1 /2 HG-W Rc2 32

38 EXH HG-WR* Series imensions: HG-WR* Series HG-WR*-15/ Rc1/ EXH E Model No. E HG-WR* Rc1/2 HG-WR* Rc3/4 HG-WR*-25/32/40/50 HG-WR*-40/50 ctuator Rc1/ F Rc1/8 G H 39 EXH E Model No. E F G H HG-WR* Rc HG-WR* Rc1 1 / HG-WR* Rc1 1 / HG-WR* Rc

39 ir operated type 2-port ball valve with solenoid valve (compact rotary valve) H-WV1/H-WX1 Series : Rc3/8 to Rc2 JIS symbol H-WV1 (double acting-n) H-WX1 (single acting-n) ommon specifications H-WV1 H-WX1 ctuation Solenoid valve mounted type: Solenoid valve mounted type: double acting single acting Working fluid Water/air/oil (500 mm 2 /s or less) Working pressure MPa 0 to 1.0 Proof pressure (water pressure) MPa 2.0 Fluid temperature 0 to 80 (no freezing) mbient temperature -10 to 60 (no freezing) Working environment Indoors/outdoors Valve seat leakage cm 3 /min 0 (initial value at water pressure 1 MPa) Mounting orientation Vertical direction with the actuator on top Frequency times/min 1 or less Pilot fluid ompressed air Lubrication Not required (use turbine oil class 1 ISO VG32 as necessary) Proof pressure (water pressure) MPa 1.5 Working pressure MPa 0.35 to to 0.7 Fluid temperature 5 to 60 S, E1, E2 port Rc1/4 EXH port Rc1/8 Electrical specifications Rated voltage 100 V (50/60 Hz), 200 V (50/60 Hz), 24 V 100 V 0.170/0.140 (50/60 Hz) Starting 200 V 0.090/0.070 (50/60 Hz) current () 24 V V 0.100/0.080 (50/60 Hz) Holding 200 V 0.050/0.040 (50/60 Hz) current () 24 V V 5.0/4.0 (50/60 Hz) Power 200 V 5.0/4.0 (50/60 Hz) consumption (W) 24 V 6.0 Thermal class lass 130 () egree of protection IP65 Voltage fluctuation range ±10% Rotary actuator Individual specifications Orifice size Weight (kg) v Model No. (mm) ouble acting Single acting H-WV1/WX1-10- Rc3/ H-WV1/WX1-15- Rc1/ H-WV1/WX1-20- Rc3/ H-WV1/WX1-25- Rc H-WV1/WX1-32- Rc1 1 / H-WV1/WX1-40- Rc1 1 / H-WV1/WX1-50- Rc Standard bore 34

40 H-WV1/H-WX1 Series How to order H WV1 25 E S 100V Model No. ctuator ody material oil option E Other options F Voltage WV1 WX1 E ctuator ouble acting N (normally closed) type Single acting N (normally closed) type 10 Rc3/8 15 Rc1/2 20 Rc3/4 25 Rc1 32 Rc1 1 /4 40 Rc1 1 /2 50 Rc2 E L ody material Stainless steel oil option Round terminal box With round terminal box Other options lank None F S Silencer*1 Voltage 100V 100 V 50/60 Hz, 110 V 60 Hz 200V 200 V 50/60 Hz, 220 V 60 Hz 24V 24 V *1: For WV1, the product comes with two SL-8-W made by K. For WX1, it comes with one. Model No. H (standard bore) <Example of model No.> H-WV1-25-E-S-100V Model No.: H (standard bore) ctuator : ouble acting N (normally closed) type : Rc1 ody material : Stainless steel oil option : With round terminal box E Other options : With two silencers F Voltage : 100 V 50/60 Hz. 110 V 60 Hz 35

41 imensions: H-WV1 Series H-WV1-10/15/20/ H-WV1 Series imensions Pilot (S) Rc1/4 F 34 Pilot EXH (E1, E2) 2 Rc1/4 2 E Model No. E F H-WV Rc3/8 144 H-WV Rc1/2 144 H-WV Rc3/4 150 H-WV Rc1 153 H-WV1-32/40/ F 39 2 E Model No. E F H-WV Rc11/4 160 H-WV Rc11/2 166 H-WV Rc

42 H-WX1 Series imensions: H-WX1 Series H-WX1-10/15/ Pilot (S) Rc1/4 F 34 reathing hole (EXH) Rc1/8 Pilot EXH (E1, E2) 2 Rc1/4 2 E H-WX1-40/50 ctuator Model No. E F 53 H-WX Rc3/8 144 H-WX Rc1/2 144 H-WX Rc3/4 150 H-WX1-25/32/40/ F 39 reathing hole (EXH) Rc1/8 Pilot EXH (E1, E2) 2 Rc1/4 Model No. E F H-WX Rc1 153 H-WX Rc11/4 160 H-WX Rc11/2 194 H-WX Rc

43 ir operated type 3-port ball valve with solenoid valve (compact rotary valve) HG-WV1/HG-WX1 Series : Rc1/2 to Rc2 JIS symbol HG-WV1 (ouble acting, normally - path) HG-WX1 (Single acting, normally - path) ommon specifications HG-WV1 HG-WX1 ctuation Solenoid valve mounted type: double acting Solenoid valve mounted type: single acting Working fluid Water/air/oil (500 mm 2 /s or less) Working pressure MPa 0 to 1.0 Proof pressure (water pressure) MPa 2.0 Fluid temperature 0 to 80 (no freezing) mbient temperature -10 to 60 (no freezing) Working environment Indoors/outdoors Valve seat leakage cm 3 /min 0 (initial value at water pressure 1 MPa) Mounting orientation Vertical direction with the actuator on top Frequency times/min 1 or less Pressurization direction Port pressurization only Flow path shape Multi-fluid type (90 rotation switching) Pilot fluid ompressed air Lubrication Not required (use turbine oil class 1 ISO VG32 if necessary) Proof pressure (water pressure) MPa 1.5 Working pressure MPa 0.35 to to 0.7 Fluid temperature 5 to 60 Port S, E1, E2 port Rc1/4 size EXH port Rc1/8 Electrical specifications Rated voltage 100 V (50/60 Hz), 200 V (50/60 Hz), 24 V 100 V 0.170/0.140 (50/60 Hz) Starting 200 V 0.090/0.070 (50/60 Hz) current () 24 V V 0.100/0.080 (50/60 Hz) Holding 200 V 0.050/0.040 (50/60 Hz) current () 24 V Power 100 V 5.0/4.0 (50/60 Hz) consumption 200 V 5.0/4.0 (50/60 Hz) (W) 24 V 6.0 Thermal class lass 130 () egree of protection IP65 Voltage fluctuation range ±10% Rotary actuator Individual specifications Orifice size Weight (kg) v Model No. (mm) ouble acting Single acting HG-WV1/WX1-15- Rc1/ HG-WV1/WX1-20- Rc3/ HG-WV1/WX1-25- Rc HG-WV1/WX1-32- Rc1 1 / HG-WV1/WX1-40- Rc1 1 / HG-WV1/WX1-50- Rc

44 HG-WV1/HG-WX1 Series How to order HG WX1 15 E S 200V Model No. ctuator ody material oil option E Other options F Voltage ctuator WV1 ouble acting, normally - path WX1 Single acting type, normally - path 15 Rc1/2 20 Rc3/4 25 Rc1 32 Rc1 1 /4 40 Rc1 1 /2 50 Rc2 ody material E Stainless steel oil option Round terminal box L With round terminal box E Other options lank None S Silencer*1 F Voltage 100V 100 V 50/60 Hz, 110 V 60 Hz 200V 200 V 50/60 Hz, 220 V 60 Hz 24V 24 V *1: For WV1, the product comes with two SL-8-W made by K. For WX1, it comes with one. <Example of model No.> HG-WX1-15-E-S-200V Model: HG ctuator : Single acting type, normally - path : Rc1/2 ody material : Stainless steel oil option : With round terminal box E Other options : With one silencer F Voltage : 200 V 50/60 Hz. 220 V 60 Hz 39

45 imensions: HG-WV1 Series HG-WV1 Series imensions HG-WV1-15/20/ Pilot (S) Rc1/4 F 34 Pilot EXH (E1, E2) 2 Rc1/4 3 E Model No. E F HG-WV Rc1/2 144 HG-WV Rc3/4 150 HG-WV Rc1 153 HG-WV1-32/40/ F 39 3 E Model No. E F HG-WV Rc11/4 160 HG-WV Rc11/2 166 HG-WV Rc

46 HG-WX1 Series imensions: HG-WX1 Series HG-WX1-15/ Pilot (S) Rc1/4 F 34 reathing hole (EXH) Rc1/8 Pilot EXH (E1, E2) 2 Rc1/4 3 E HG-WX1-40/50 ctuator Model No. E F HG-WX Rc1/2 144 HG-WX Rc3/ HG-WX1-25/32/40/ F 39 reathing hole (EXH) Rc1/8 Pilot EXH (E1, E2) 2 Rc1/4 Model No. E F HG-WX Rc1 153 HG-WX Rc11/4 160 HG-WX Rc11/2 194 HG-WX Rc

47 ir operated type 2-port ball valve (compact rotary valve) S-W/S-WR* Series : Rc3/8 to Rc2 JIS symbol S-W (double acting) S-WR1 (single acting-n) S-WR2 (single acting-no) ommon specifications s S-W S-WR* ctuation ir operated type: double acting ir operated type: single acting Working fluid Steam/hot water Working pressure MPa 0 to 0.6 Proof pressure (water pressure) MPa 2.0 Fluid temperature 0 to 164 (no freezing) mbient temperature -10 to 60 (no freezing) Working environment Indoors/outdoors Valve seat leakage cm 3 /min 1 or less (initial value at water pressure 0.6 MPa) Mounting orientation Free Frequency times/min 1 or less Pilot fluid ompressed air Lubrication Not required (use turbine oil class 1 ISO VG32 if necessary) Proof pressure (water pressure) MPa 1.5 Working pressure MPa 0.35 to to 0.7 Fluid temperature 5 to 60 Rc1/8 Rotary actuator Individual specifications Orifice size Weight (kg) v Model No. (mm) ouble acting Single acting S-W(R*)-10 Rc3/ S-W(R*)-15 Rc1/ S-W(R*)-20 Rc3/ S-W(R*)-25 Rc S-W(R*)-32 Rc1 1 / S-W-40 Rc1 1 / S-W-50 Rc Note 1: S-(WR*)-10 is full bore type. Note 2: S-(WR*)-40/50 is not available. Standard bore 42

48 S-W Series How to order S WR1 15 W Model No. ctuator ctuator W ouble acting type WR1 Single acting N (normally closed) type WR2 Single acting NO (normally open) type Model No. S (Standard bore) * Rc3/8 Rc1/2 Rc3/4 Rc1 Rc1 1 /4 Rc1 1 /2 Rc2 ody/seat material ody/seat material W Stainless steel - reinforced PTFE *1: S-WR*-40/50 is not available. <Example of model No.> S-WR1-15-W Model: S (standard bore) ctuator : Single acting N (normally closed) type : Rc1/2 ody/seat material : Stainless steel - reinforced PTFE 43

49 imensions: S-W Series S-W-10/15/20/25/32/40/50 S-W/S-WR* Series imensions S-W-32/40/50 ctuator Rc1/ Rc1/ E Model No. S-W-10 S-W-15 S-W-20 S-W-25 S-W-32 S-W-40 S-W-50 E Rc3/8 Rc1/2 Rc3/4 Rc1 Rc1 1 /4 Rc1 1 /2 Rc2 imensions: S-WR* Series S-WR*-10/15/20/25/ Rc1/8 S-WR*-25/32 ctuator Rc1/ E Model No. S-WR*-10 S-WR*-15 S-WR*-20 S-WR*-25 S-WR*-32 E Rc3/8 Rc1/2 Rc3/4 Rc1 Rc1 1 /4 44

50 45

51 46

52 ustom Order Product Main line filter F3000 Series Outdoor type 47 Specifications F F F F F F F F F Processing air flow rate (Note 2, Note 3) m 3 /min (NR) Working fluid ompressed air Working pressure MPa 0.07 to 1.0 Proof pressure MPa 1.5 Element quantity (Note 1) Flange Weight kg indicates series name. P-type S-type M-type X-type mbient temperature 5 to 60 5 to 30 Filtration rating μm Suction by activated carbon Secondary side oil concentration mg/m (inlet air 30 ) 0.1 (inlet air 30 ) 0.03 (inlet air 30 ) Initial MPa Within Within 0.01 Within 0.01 Within 0.01 Normal MPa to to to Element replacement MPa ifferential pressure gauge Standard (model No.: G5012-S11) rain discharger Standard (model No.: MG) None Pressure drop Note 1: Flange is 10K flange. Note 2: Processing air flow rate is the atmospheric pressure conversion value where inlet pressure is 0.7 MPa and initial pressure drop is MPa. Note 3: NR shows the conditions when the relative humidity of atmospheric pressure air at 20 is 65%. How to order F3 016 P 50 Flow rate classification Element type LO Option /flow rate classification table Flow rate classification Flange 2 80 Flange Flange Flange Flange 8 Note on model No. selection Note 1: Viewed from the front, the standard product has the air inlet on the left and the air outlet on the right. For "X1", air inlet is provided on the right port, while air outlet is provided on the left port. Note 2: vailable for F3032P to F3256P. Note 3: When ordering several options, indicate the required options in alphabetical order. Flow rate classification m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) Element type P P Series (pre filter) S S Series (oil removal filter) M M Series (high performance oil removal filter) X X Series (activated charcoal filter) Refer to the port size/flow rate classification table on the left. Option lank None F Specified color paint H English specifications H1 Export packing K ompanion flange attached L Foundation bolt/nut attached (Note 2) L1 Stainless steel foundation bolt/nut attached (Note 2) O Outdoor type X1 - reverse direction (Note 1) Y2 Product photo Flow characteristics Processing air flow rate (m 3 /min NR) Primary side pressure (MPa) F F3256P F3192P F3160P F3128P F3096P F3080P F3064P F3048P F3032P F3016P Note on selection 1. Never choose model No. found below the intersection identified with the selection conditions. 2. When the intersection identified with the selection conditions is on the flow characteristics curves, choose the model No. one size larger. Otherwise, the service life may be shortened. 3. The unit s performance may not be attained if used at a pressure lower than the selected pressure. lways select the model No. for the working pressure.

53 Internal structure and parts list imensions F3000 Series Internal structure and parts list/dimensions Parts list *Repair part No. Parts name Material 1 Upper flange SS400 2 *Gasket NR 3 ody SS400 4 *Element kit PP, NR etc. 5 *rain discharger Z, P etc. The drain discharger and stop valve are attached. Repair parts model No. Flow rate rain classification 2 Gasket 4 Element kit 5 m 3 /min (NR) discharger 16 F3016P GSKET F3016 ELEMENT-KIT (1) 32 F3032P GSKET F3032 ELEMENT-KIT (2) 48 F3048P GSKET F3048 ELEMENT-KIT (3) 64 F3064P GSKET F3064 ELEMENT-KIT (4) 80 F3080P GSKET F3080 ELEMENT-KIT (5) 96 F3096P GSKET F3096 ELEMENT-KIT (6) MG 128 F3128P GSKET F3128 ELEMENT-KIT (8) 160 F3160P GSKET F3160 ELEMENT-KIT (10) 192 F3192P GSKET F3192 ELEMENT-KIT (12) 256 F3256P GSKET F3256 ELEMENT-KIT (16) ( ) indicates the element quantity indicates the series name. F3016 F3032 to 3256 E F G E F G Installation legs foundation bolt hole dimension H 4-φ K J rain discharger MG rain discharge port Rc1/4 rain discharger MG rain discharge port Rc1/4 X Series does not come with the drain discharger and the stop valve. Model No. E F G Model No. H J K F Flange M20 70 M F φ 15 F Flange M22 80 M F φ 15 F Flange M22 80 M F φ 15 F Flange M22 80 M F φ 15 F Flange M22 80 M F φ 15 F Flange M24 90 M F φ 15 F Flange M24 90 M F φ 15 F Flange M24 90 M F φ 15 F Flange M M F φ 15 F Flange M M indicates series name. 48

54 ustom Order Product Main line filter F5000 Series Outdoor type 49 Specifications F F F F F F F F F Processing air flow rate (Note 2, Note 3) m 3 /min (NR) Working fluid ompressed air Working pressure MPa 0.08 to 1.0 Proof pressure MPa 1.5 Element quantity (Note 1) Flange Weight kg indicates series name. P-type S-type M-type X-type mbient temperature 5 to 60 5 to 30 Filtration rating μm Suction by activated carbon Secondary side oil concentration mg/m (inlet air 21 ) 0.01 (inlet air 21 ) (inlet air 21 ) Pressure drop Initial MPa Within Within 0.01 Normal MPa Element replacement MPa ifferential pressure gauge Standard (model No.: G5012-S11) None rain discharger Standard (model No.: MG) None Note 1: Flange is 10K flange. Note 2: Processing air flow rate is the atmospheric pressure conversion value where inlet pressure is 0.7 MPa and initial pressure drop is MPa. Note 3: NR shows the conditions when the relative humidity of atmospheric pressure air at 20 is 65%. How to order F5 016 P 50 X1 Flow rate classification Element type /flow rate classification table Option Flow rate classification Flange 2 80 Flange 3 Flange Flange Flange 8 Flow rate classification m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) m 3 /min (NR) Element type P P Series (pre filter) S S Series (oil removal filter) M M Series (high performance oil removal filter) X X Series (activated charcoal filter) Refer to the port size/flow rate classification table below to the left. Option lank Standard products rain discharger (Note 1) E Without drain discharger K ompanion flange attached H English specifications H1 Export packing H2 SUS tag plate L Foundation bolt/nut attached (SS400) (Note 2) L1 Foundation bolt/nut attached (SUS304) (Note 2) X1 - reverse direction (Note 3) Y2 Product photo F Flow rate compensation coefficient Pressure (MPa) ompensation coefficient If working pressure is other than 0.7 MPa, multiply the processing air flow rate by the above coefficient. Note on model No. selection Note 1: "" drain discharger is recommended for a working environment where electric wiring is not feasible. Note 2: "L" and "L1" are applicable to F5032P through F5256P. Note 3: Viewed from the front, the standard product has the air inlet on the left and the air outlet on the right. For "X1," the air inlet is on the right and the air outlet is on the left. Note 4: The unit s performance may not be attained if used at a pressure lower than the selected pressure. lways select the model No. for the working pressure. Note 5: When ordering several options, indicate the required options in alphabetical order.

55 imensions F5000 Series imensions F5016 F5032 to F and over 315 φ 280 M12 8-M20 70 G F E 2-2 Flange (1056) (1261) 755 rain discharger MG rain discharge port Rc1/4 H rain discharger MG rain discharge port Rc1/4 X-type does not come with the differential pressure gauge. Foundation bolt hole dimension J 4-φ K J Model No. E F G H J K F Flange φ M22 80 M φ φ 15 F Flange φ M22 80 M φ φ 15 F Flange φ M22 80 M φ φ 15 F Flange φ M22 80 M φ φ 15 F Flange φ M24 90 M φ φ 15 F Flange φ M24 90 M φ φ 15 F Flange φ M24 90 M φ φ 15 F Flange φ M M φ φ 15 F Flange φ M M φ φ 15 indicates series name. 50

56 F5000 Series Repair parts list Gasket Element kit Ordering method Flow rate classification m 3 /min (NR) Gasket Element kit rain discharger 16 F5016P GSKET F5016 ELEMENT-KIT 32 F5032P GSKET F5032 ELEMENT-KIT 48 F5048P GSKET F5048 ELEMENT-KIT 64 F5064P GSKET F5064 ELEMENT-KIT 80 F5080P GSKET F5080 ELEMENT-KIT 96 F5096P GSKET F5096 ELEMENT-KIT 128 F5128P GSKET F5128 ELEMENT-KIT 160 F5160P GSKET F5160 ELEMENT-KIT 192 F5192P GSKET F5192 ELEMENT-KIT 256 F5256P GSKET F5256 ELEMENT-KIT MG indicates series name. X-type does not come with the drain discharger and the differential pressure gauge. rain discharger ustom Order Product Refrigerating type dryer GT9000 Series Stainless steel heat exchanger for oil-free air Weather resistance equivalent to IP03 Energy-saving operation with 50% decreased power by limiting the number of refrigerating systems (GT9300 (W) - GT9450 (W)) Energy-saving operation with 60% decreased power by inverter control (GT9710WV, GT9960WV) Easy maintenance Free installation in any location 51

57 Safety Precautions W Series: Warning and autions lways read this section before use. For general and product-specific precautions, refer to "Pneumatic, Vacuum and uxiliary omponents (-024S)," "Pneumatic Valves (-023S)," and "General Purpose Valves (-03-1S)." Pressure gauges (Outdoor Series) * For product-specific precautions other than below, refer to Product-specific precautions for FRL Unit (modular type) and FRL Unit (compact type) in "Pneumatic, Vacuum and uxiliary omponents (-024S)." WRNG For designing and reviewing This product is designed for industrial use. o not use for medical purposes, or any system or circuit that concerns human life. Install a safety device where an output pressure exceeding the regulator's set pressure value could result in damage or faulty operation of secondary side devices. Working environment This product is designed for outdoor use, but do not use them in the following environments. place where the ambient temperature or the product temperature falls outside the range of -10 to 60. (When used in sunlight, the product temperature may become higher than the ambient temperature.) Where air freezes. If the atmosphere contains corrosive gas, liquid or chemical material. place where vibration and impact are present. uring use & maintenance o not disassemble the filter regulator and the regulator cover. UTION uring use and maintenance Tighten the hexagon nut to secure the adjusting screw except when you adjust the pressure. (If used without tightening the hexagon nut, the product may be damaged.) o not apply a load other than what may be applied to the product during normal operation. (o not step onto this product.) When you install the regulator cover facing downward, a pressure adjustment failure due to freezing may occur. Take heed when you use the product in a cold environment. The set pressure changes from the initial set value based on the working environment and conditions, as well as aging of part materials. Periodically check the pressure, and should there be a change, reset the pressure accordingly. Perform periodic maintenance for every six months or twelve months. Repair parts (metal bowl assembly, valve assembly, bottom spring, element, mantle assembly, and O-rings) should be replaced once every year. For repair parts, contact K. When the set pressure is high, a force required to turn the adjusting screw (knob) becomes large. Working fluid Use only compressed air. ir containing corrosive gases, fluids or chemicals could result in improper pressure adjustment due to body damage or rubber deterioration. Hexagon nut Width across flats 17 mm djusting screw Width across flats 6 mm Others The product is guaranteed for outdoor use, but corrosion resistance (no rusting and no discoloration) is not guaranteed. When you tighten a fitting to the drain discharge port of the metal bowl with auto-drain, secure the hexagon section of the adapter nut when you tighten the fitting. If the hexagon section of the adapter nut is not secured, the product may be damaged due to overtightening of the adapter nut. If you use a tightening joint for the drain of the metal bowl with auto-drain, manual operation becomes impossible. The piston drain is an automatic discharge type for an intermittent flow. rainage is not discharged under working conditions where air flows constantly. O S rain discharge port Metal bowl (uto-drain) daptor nut (Hexagon head type) 52

58 Safety Precautions W Series: Warning and autions lways read this section before use. For general and product-specific precautions, refer to "Pneumatic, Vacuum and uxiliary omponents (-024S)," "Pneumatic Valves (-023S)," and "General Purpose Valves (-03-1S)." Silencer speed controller (outdoor series) * For precautions other than below, refer to Product-specific precautions for Silencer Speed ontroller in "Pneumatic, Vacuum and uxiliary omponents (-24S)." WRNG For designing and reviewing This product is designed for industrial use. o not use for medical purposes, or any system or circuit that concerns human life. Working environment This product is designed for outdoor use, but do not use them in the following environments. place where the ambient temperature or the product temperature falls outside the range of -10 to 60. (When used in sunlight, the product temperature may become higher than the ambient temperature.) Where air freezes. If the atmosphere contains corrosive gas, liquid or chemical material. place where vibration and impact are present. uring use and maintenance o not disassemble the speed controller. o not install the silencer exhaust port facing upward. Take measures so that dirt and rain do not enter the exhaust port. UTION uring use and maintenance o not apply a load other than what may be applied to the product during normal operation. (o not step onto this product.) Take care not to loose the circlip for the silencer during removal or installation. Install the circlip correctly when you replace the silencer element. Inner parts may pop out and cause problems if assembly is incorrect. epending on the type of job, the silencer may get clogged restricting exhaust flow. Inspect, clean, and replace the silencer element periodically. Working fluid Use only compressed air. ir containing corrosive gases, fluids, or chemicals may cause body damage or rubber deterioration. Others The product is guaranteed for outdoor use, but corrosion resistance (no rusting and no discoloration) is not guaranteed. 53

59 Safety Precautions W Series: Warning and autions lways read this section before use. For general and product-specific precautions, refer to "Pneumatic, Vacuum and uxiliary omponents (-024S)," "Pneumatic Valves (-023S)," and "General Purpose Valves (-03-1S)." General purpose valve K11-W/H/G-W (outdoor series) * For precautions other than below, refer to Product-specific precautions for K/H/G in "General Purpose Valves (No.-03-1S)." WRNG For designing and reviewing This product is designed for industrial use. o not use for medical purposes, or any system or circuit that concerns human life. The W series is not certified as explosion-proof. o not use the product in the environment where an explosion-proof product is required. Working environment This product is designed for outdoor use, but do not use them in the following environments. place where the ambient temperature exceeds the specification range. (When used in sunlight, the product temperature may become higher than the ambient temperature.) place where the fluid freezes. If the atmosphere contains corrosive gases, liquids, chemicals, or explosive gases. place where vibration and impact are present. UTION Wiring (K-W Series and H/G-W Series) 1) Precautions for disassembly and assembly Precautions for installing a cap The cap must be assembled in a certain direction. When you install the cap after a wiring job, make sure to install the cap in the correct orientation. (lign the cap with the K log as shown In the figure below.) When The cap cannot be properly assembled otherwise. 2) Wiring (1) The crimp terminals of wiring should be properly crimped for all the wires. * Use the M3 terminal screws and the crimp terminals whose outer diameter is 7 mm or less. * Use the covered crimp terminals. (2) Tighten the screws for the following tightening torque. * ap set screw tightening torque: 0.5 N m * Terminal screw tightening torque: 0.5 N m (3) The coil has two lead wires to be connected to the terminal block. * The terminal boxes without indicator lights 3E (K11-W Series), (H/G-W Series) and terminal boxes with indicator lights 3L (K11-W Series) have no polarity. onnect either wire to Terminal or Terminal. * The terminal boxes with indicator lights and L (H/G-W Series) have polarity for. Make sure to confirm the polarity when you wire them. onnect Terminal of the terminal block to the negative pole and Terminal to the positive pole. (If you make incorrect connection, the solenoid valve works but the indicators do not come on.) Note: For safety and protection of the device, we recommend a fuse in the electric circuit. Wiring side oil side Wiring side oil oil side 54

60 Safety Precautions W Series: Warning and autions lways read this section before use. For general and product-specific precautions, refer to "Pneumatic, Vacuum and uxiliary omponents (-024S)," "Pneumatic Valves (-023S)," and "General Purpose Valves (-03-1S)." General purpose valve K11-W/H-W (outdoor series) * For precautions other than below, refer to Product-specific precautions for K/H in "General Purpose Valves (No.-03-1S)." UTION When using The male thread of the round terminal box is secured to the solenoid valve coil with adhesive. o not remove the round terminal box or change the orientation of the wiring port. Rain may enter the round terminal box through the male thread section. o not configure the exhaust ports for atmospheric pressure release. Make sure to implement measures to prevent foreign objects, dust, and rainwater from entering the body. In addition, implement waterproof measures for the electrical wires and piping using cable glands, etc. ctuator (ctuation type) Port W (ouble acting type) - WR* (Single acting type) EXH V1 (ouble acting type with solenoid valve) E1, E2 X1 (Single acting type with solenoid valve) E1, E2, EXH * When you use a silencer, install it to E1 and E2 for the type V1 and to E1 for the type X1. Manual override (H-W Series) Use the manual button to confirm the proper operation during test. When used for a long period of time in the locked state, the locking mechanism may break and switch the unit from ON to OFF. Manual operating device s this is a pilot solenoid valve, the main valve will not switch over even if the manual override is operated unless air is supplied to the S port. Locking manual override When you turn the locking manual override by approximately 45 with a screwdriver, the valve becomes energized and is locked. You can only rotate in the clockwise direction. o not force the rotation as rotating the device further after the valve has been locked will cause damage. e sure to release the lock (0 position) of the locking manual override prior to starting operation. Others The product is guaranteed for outdoor use, but corrosion resistance (no rusting and no discoloration) is not guaranteed. This product has the performance which enables outdoor use in standard environmental conditions. These are products that satisfy certain performance requirements after implementation of an accelerated weathering test (sunshine weathering meter) for 1,000 hours and a (salt, dry, moisture) compound cycle test for 960 hours. However, the risk of defects such as rust occurring in a short amount of time may increase when using the unit in a special environment. ontact K when using this device in a special environment. 55