ARM1000/2000. Standard Specifications

Transcription

1 .5-

2 Regulator Manifold ARM000/000 4 connection methods Standard Specifications Fluid Proof pressure Max. operating pressure Set pressure range Ambient and fluid temperature Cracking pressure (Valve) Construction Air.MPa 0.8MPa 0.05 to 0.7MPa 5 to 60 C 0.0MPa Relieving style Small size pressure gauge ø5 Backflow function available on the standard model Space saving Port Size/Weight Piping ARM000 ARM000 How to Order Port size Weight (g) Total weight (n: stations) Regulator (Except manifold) 8 8 (80 X n) (79 X n) (88 X n) (87 X n) ARM 000 Regulator for manifold 5 A 0 G Option Set at 0.MPa Pressure gauge for MPa is used. Only the adjusting spring is different from the standard model. ARM000-4B ARM000-6A-0G Body size Number of stations station 0 0 stations Piping A Manifold side Common A Body side B Manifold side Individual B Body side In case of A and B, a pressure gauge or a plug is mounted on the body side, while in case of A and B, on the manifold side. When mounting a pressure gauge on the body side, its front faces to the adjusting screw. Port size ( side) 0 8 Thread N Accessory G Rc(PT) NPT None (with plug) Pressure gauge In case of a single regulator without a manifold base, indicate "ARM000A or ARM000A." When a regulator is not mounted on the manifold, use the following blank plate ass'y (with mounting screws and ) For ARM000: Part no. 364A For ARM000: Part no. 364A ARM000-4A-0G Option: Pressure gauge G5-0-0 How to Order 0 M5 G5 0 0 ø Max. pressure indication 0.0MPa Pressure gauge for 0.MPa Connecting thread 0 8 male thread, M5 female thread Precautions: When drain or oil gets into the gauge, an error is shown on the display. Thread N Rc(PT) NPT

3 Regulator Manifold ARM000/000 Construction () Flow Characteristics Component Parts No. Description q Body w Manifold e Valve guide r Piston t Adjusting spring y Adjusting screw Replacement Parts No. u i o!0! Setting Description Valve Valve spring Valve guide Material Brass/ Stainless steel POM qmake sure to check the primary pressure before setting the secondary pressure. Turning the pressure adjustment handle clockwise increases the secondary pressure and turning it counterclockwise decreases the pressure. (To set Material ADC Aluminum alloy Brass Brass Steel wire Steel Precautions Part no. ARM X 3.5 X.5 JIS B 40P7 Note Chromate Chromate Zinc chromate Electroless nickel plated ARM X 0 X.5 JIS B 40P8 the pressure, do so in the direction of pressure increase.) wthe secondary pressure must be set to 85% or less of the primary pressure. Be sure to read before handling. Refer to p.0-6 and 0-7 for Safety Instructions and common precautions on the products mentioned in this catalogue, and refer to p..0- and.0-3 for precautions on every series. Pressure Characteristics Initial setting Supply pressure: 0.7MPa Secondary pressure: 0.MPa Flow: 0 l/min (ANR) Warning Caution Mounting/Adjustment qin the case of the common style, supply pressure from the two ports from both ends. Failure to observe this procedure could lead to an excessive pressure drop. wset up the regulator while verifying the pressure that is indicated on the primary and the secondary pressure gauges. Turning the handle excessively could damage the internal parts. qrelease the lock to adjust the pressure. After the adjustment, engage the lock. Failure to observe this procedure could damage the handle or cause the secondary pressure to fluctuate. Warning Maintenance qmake sure to perform a periodic inspection of the pressure gauge when it is used by installing it between a solenoid valve and an actuator, etc. Because of the possibility of creating sudden pressure fluctuations, the durability of the product could be shortened. Under certain circumstances, the use of an electronic style pressure gauge is recommended..5-3

4 Dimensions ARM000 ARM000 ARM000 ARM000 L L L L Manifold stations (n) A B C D 8 E 8 7 F G 6 0 H 9.5 J 8 4 K 9 8 M 5 66 P 9.5 Q R Dimensions Dimensions by Number of Stations ARM000/000

5 Regulator Manifold Modular Style /3000 A modular style that can be freely mounted on a manifold station. Optimal for central pressure control. Easily set up using the new handle. Also has a One-touch lock system. E ARM 500 Regulator manifold Ordering source area code - E N Japan, Asia Australia Europe North America Body size Number of stations 0 stations How to Order 05 A F - Rc(PT) E NPT N G(PF) Piping Style A B 0 G Accessories (Options) None (with plug) G G G GA Pressure gauge is attached, not mounted. Port size ( side) Port size 0 03 Rc (PT) /4 Rc (PT) 3/8 Applicable model From end plate From port or G port 0 0 stations Standard Specifications Proof pressure Max. operating pressure Set pressure range Ambient and fluid temperature Fluid Construction.5MPa.0MPa 0.05 to 0.85MPa 5 to 60 C(Non-freezing) Air Relieving style Port Size/Weight Piping Port size Rc(PT) Body End plate Pressure gauge port size Rc(PT) Weight (kg) Regulator End plate Weight by Number of Stations Stations (kg).5-5

6 /3000 Option: Pressure Gauge (Max. pressure indication.0mpa) Flow Characteristics Supply pressure: 0.7MPa Option: Mounting Bolt Assembly Part No Option: Bracket Assembly Dimensions Hexagon socket head cap screw (M5 x 70) Hexagon socket head cap screw (M6 x 85) style can be used as a single regulator. Qty. 4 4 Note With flat washer With flat washer Pressure Characteristics Initial setting P: 0.7MPa P: 0.MPa Q: 0 l/min (ANR) Part No. A B C D E F G.3.3 Precautions Be sure to read before handling. Refer to p.0-6 and 0-7 for Safety Instructions and common precautions on the products mentioned in this catalogue, and refer to p..0- and.0-3 for precautions on every series. Warning q The adjustment handle must be operated manually. Using a tool to turn the handle could lead to damage. w Set up the regulator while verifying the pressure that is indicated on the primary and the secondary pressure gauges. Turning the handle excessively could damage the internal parts. Caution q Release the lock to adjust the pressure. After the adjustment, engage the lock. Failure to observe this procedure could damage the handle or cause the secondary pressure to fluctuate. A) On the type, pull the adjustment handle to release the lock and push the adjustment handle to engage the lock. If it does not lock easily, turn the handle slightly clockwise or counterclockwise before pushing it. Mounting/Adjustment B) On the type, pull the adjustment handle to release the lock. (An orange colored line is provided at the bottom of the adjustment handle for visual checking.) Push the adjustment handle to engage the lock. If it does not lock easily, turn the handle slightly clockwise or counterclockwise; then, push it until the orange colored line is no longer visible. wturning the pressure adjustment handle clockwise increases the secondary pressure and turning it counterclockwise decreases the pressure. e Make sure to check the primary pressure before setting the pressure. The secondary pressure must be set to 85% or less of the primary pressure. Failure to observe this procedure could cause the secondary pressure to fluctuate. r In the case of the common style, supply pressure from the two ports from both ends. Failure to observe this procedure could lead to an excessive pressure drop.

7 Construction Regulator Manifold /3000 Component Parts No. Description Material q Body Aluminum die cast w Bonnet Polyacetal Replacement Parts No. e r t y u i Description Diaphragm ass'y Valve ass'y Valve spring Valve Material Brass/ Stainless steel Note Chromate/Painted silver Description No. Component Qty. 3496A 3639A 3630 Part No..5 X 8.5 X X 0.5 X JIS B40 P3 8 X 5 X.5 355A 3649A 3640 JIS B40 P5 35 X 3 X Component Parts Assembly Regulator o End plate ass'y Bracket ass'y!0!!!3!!3 Regulator End plate R End plate L Bracket Bracket Bracket A Bracket B Hex. socket set head cap screw Bracket A Bracket B Hex. socket head cap screw set -A-0 -A-0 -A-0 -A A 3636B (Except for ) Part No. 3646A B (Except for ) How to Order 500 A () When adding n stations to ARM B: Regulator n pcs. Bracket ass'y n pcs. () When regulators, end plate assembly and bracket assembly are assembled to make the manifold of n stations. Regulator n pcs. Bracket ass'y n pcs. End plate ass'y pc..5-7

8 /3000 Dimensions Dimensions A 6 7 B C D E F G H I J K L M N O P Dimensions by Number of Stations L L L3 L L L Manifold stations